AVM FRITZ!Box Fon WLAN 6840
This box is using a Lantiq SoC, see soc.lantiq The box is currently supported as “stable” in LEDE since 17.01 (reboot). The DECT does not work and is not supported due to missing PIGLET and DECT Driver (AVM driver is closed source). If you need DECT and/ or fully phone support, you should take a look at freetz. Phone works only via SIP with asterisk or another SIP package and a wifi or ethernet SIP phone.
Supported Versions
Version/Model | Launch Date | OpenWrt Version Supported | Model Specific Notes |
---|---|---|---|
v1 | 2011 | WIP |
Hardware Highlights
Info
Rev B | |
---|---|
Architecture | VR9-MIPS32 34Kc |
CPU-Cores | 2 |
Vendor | Lantiq |
Bootloader | EVA |
System-On-Chip | PSB80920EL V1.1 |
CPU/Speed | 500 MHz |
S-Flash-Chip | MX25L2006 |
S-Flash size | 256 KiB |
N-Flash-Chip | HY27UF081G2A |
N-Flash size | 128 MiB |
RAM-Chip | |
RAM size | 128 MiB |
Modem | Yes LTE |
Wireless | 2.4GHz 802.11bgn |
Ethernet | 4x 1 Gbit/s w/ vlan support |
Phone | 1x FXS |
USB | Yes |
Serial | Yes |
Flash Layout
The OEM Flash layout is:
FRITZ!Box 6840 OEM Flash Layout | |||||||||
---|---|---|---|---|---|---|---|---|---|
Layer0 | 128MiB | ||||||||
Layer1 | mtd0 reserved-kernel 4MiB | mtd1 reserved-filesystem 48MiB | mtd2 Kernel 4MiB | mtd3 filesystem 48MiB | mtd4 config 2MiB | mtd5 nand-filesystem 22MiB |
Serial
Bootlogs
OEM bootlog
(AVM) EVA Revision: 1.1475 Version: 2475 (C) Copyright 2005 AVM Date: Nov 19 2012 Time: 11:51:38 (0) 2 0x0-0x741D [FLASH:] MACRONIX Uniform-Flash 256kB 256 Bytes WriteBuffer [FLASH:](Eraseregion [0] 4 sectors a 64kB) [NAND:] 128MB MICRON 2048 Pagesize 128k Blocksize 1024 Blocks 8Bit 1 CS [SYSTEM:] VR9 on 500MHz/250MHz/250MHz .Infineon PHY11G detected Eva_AVM >..................................................... Lantiq xDSL CPE VR9 phym = 08000000, mem = 08000000, max_pfn = 00008000 Reserving memory for CP1 @0xa8000000, size 0x00000000 plat_device_tree_setup: AVM hardware subrevision 5 plat_device_tree_setup: using Fallback device-tree of AVM hardware subrevision 2 DT: d0 0d fe ed 00 00 10 a5 [ 0.000000] Linux version 3.10.73 (jpluschke@GU_C16_vr9) (gcc version 4.8.3 (Buildroot 2014.08) ) #1 SMP Wed Feb 8 18:16:22 CET 2017 [ 0.000000] [env_init] 0x810179e0[0] [ 0.000000] [env_init] 0x81017a20[1] [ 0.000000] [env_init] 0x81017b20[2] [ 0.000000] [env_init] switch to ram location [ 0.000000] [init_avm_kernel_config] AVM Kernel Config (ptr 80847000) [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: module memory entry [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: version info entry [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 0 found [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 1 found [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 2 found [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x07ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x07ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] free_area_init_node: node 0, pgdat 8083dde0, node_mem_map 81004000 [ 0.000000] Normal zone: 256 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] [module-alloc] use 0xcc8000 bytes at 0x81105000 [ 0.000000] [0]lsmtc_smp_setup tcstatus=18102400 [ 0.000000] 1 available secondary CPU TC(s) [ 0.000000] [avm_cache_set_coherency]: setting cache coherency for HWRevision=177 to write back allocate [ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] PERCPU: Embedded 7 pages/cpu @81dd1000 s7072 r8192 d13408 u32768 [ 0.000000] pcpu-alloc: s7072 r8192 d13408 u32768 alloc=8*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 [ 0.000000] Kernel command line: console=ttyS0,115200n8r nor_size=0MB sflash_size=256KB nand_size=128MB ethaddr=5C:49:79:4D:A3:00 [ 0.000000] [NAND] nand_size = 0x8000000 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=000643da [ 0.000000] Readback ErrCtl register=000643da [ 0.000000] Memory: 107368k/131072k available (5583k kernel code, 23704k reserved, 2948k data, 292k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:181 [ 0.000000] SRSConf0 0x3feffbfe: SRS1: 0xffffffff, SRS2 0xffffffff, SRS3 0xffffffff [ 0.000000] Lantiq ICU driver, version 3.0.1, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.020000] Calibrating delay loop... 331.77 BogoMIPS (lpj=1658880) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Security Framework initialized [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] I-cache flushes single-threaded [ 0.090000] D-cache flushes single-threaded [ 0.090000] Limit of 2 TCs set [ 0.090000] TLB of 32 entry pairs shared by 2 VPEs [ 0.090000] VPE 0: TC 0, VPE 1: TC 1 [ 0.090000] IPI buffer pool of 8 buffers [ 0.090000] CPU1 revision is: 00019556 (MIPS 34Kc) [ 0.170000] TC 1 going on-line as CPU 1 [ 0.170000] Brought up 2 CPUs [ 0.170000] [yield_context_init] cpu=1 tc=2 mask=301 [ 0.180000] [yield_context_init] cpu=0 tc=3 mask=2410 [ 0.180000] devtmpfs: initialized [ 0.200000] pinctrl core: initialized pinctrl subsystem [ 0.200000] Creating Config Table [ 0.200000] [avm_generate_hw_config_table_from_device_tree] gpio_cnt: 39 [ 0.210000] NET: Registered protocol family 16 [ 0.220000] FPU Affinity set after 5000 emulations [ 0.220000] avm_check_cpu_features: mips-options: 0x006d638b icache.flags 0x00000000 dcache.flags 0x00000004 isa_level 0x00000063 ases 00000031 [ 0.230000] [TFFS3_Early_Init] called [ 0.240000] avm_alloc_page_extension node_extension_table[0] entries=32768 (size=131072) alloced [ 0.240000] Reboot Status is: Power-On [ 0.250000] [avmnet] [avmnet_cfg_init] Driver version: 6.247 - Revision 1496:3622 - Mi 8. Feb 18:15:17 CET 2017 [ 0.260000] Port 0 PLL REGFILE [ 0.260000] PCIE_PHY_PLL_CTRL1 0x8e39 [ 0.260000] PCIE_PHY_PLL_CTRL2 0x0183 [ 0.260000] PCIE_PHY_PLL_CTRL3 0x0042 [ 0.260000] PCIE_PHY_PLL_CTRL4 0x0000 [ 0.260000] PCIE_PHY_PLL_CTRL5 0x0000 [ 0.260000] PCIE_PHY_PLL_CTRL6 0x0000 [ 0.260000] PCIE_PHY_PLL_CTRL7 0x0000 [ 0.260000] PCIE_PHY_PLL_A_CTRL1 0x120e [ 0.260000] PCIE_PHY_PLL_A_CTRL2 0x39d7 [ 0.260000] PCIE_PHY_PLL_A_CTRL3 0x0900 [ 0.260000] PCIE_PHY_PLL_STATUS 0x0000 [ 0.260000] TX1 REGFILE [ 0.260000] PCIE_PHY_TX1_CTRL1 0x0009 [ 0.260000] PCIE_PHY_TX1_CTRL2 0x2e00 [ 0.260000] PCIE_PHY_TX1_CTRL3 0x1fff [ 0.260000] PCIE_PHY_TX1_A_CTRL1 0x0810 [ 0.260000] PCIE_PHY_TX1_A_CTRL2 0x0706 [ 0.260000] PCIE_PHY_TX1_MOD1 0x0000 [ 0.260000] PCIE_PHY_TX1_MOD2 0x0000 [ 0.260000] PCIE_PHY_TX1_MOD3 0x0180 [ 0.260000] TX2 REGFILE [ 0.260000] PCIE_PHY_TX2_CTRL1 0x0009 [ 0.260000] PCIE_PHY_TX2_CTRL2 0x3096 [ 0.260000] PCIE_PHY_TX2_A_CTRL1 0x8010 [ 0.260000] PCIE_PHY_TX2_A_CTRL2 0x4707 [ 0.260000] PCIE_PHY_TX2_MOD1 0x0000 [ 0.260000] PCIE_PHY_TX2_MOD2 0x0000 [ 0.260000] PCIE_PHY_TX2_MOD3 0x0180 [ 0.260000] RX1 REGFILE [ 0.260000] PCIE_PHY_RX1_CTRL1 0x0001 [ 0.260000] PCIE_PHY_RX1_CTRL2 0x3000 [ 0.260000] PCIE_PHY_RX1_CDR 0x0235 [ 0.260000] PCIE_PHY_RX1_EI 0x0004 [ 0.260000] PCIE_PHY_RX1_A_CTRL 0x6803 [ 0.270000] Port 0 PLL REGFILE [ 0.270000] PCIE_PHY_PLL_CTRL1 0x38e4 [ 0.270000] PCIE_PHY_PLL_CTRL2 0x03ee [ 0.270000] PCIE_PHY_PLL_CTRL3 0x0000 [ 0.270000] PCIE_PHY_PLL_CTRL4 0x1b72 [ 0.270000] PCIE_PHY_PLL_CTRL5 0xfae3 [ 0.270000] PCIE_PHY_PLL_CTRL6 0x3a04 [ 0.270000] PCIE_PHY_PLL_CTRL7 0x0002 [ 0.270000] PCIE_PHY_PLL_A_CTRL1 0x120e [ 0.270000] PCIE_PHY_PLL_A_CTRL2 0x39d7 [ 0.270000] PCIE_PHY_PLL_A_CTRL3 0x2900 [ 0.270000] PCIE_PHY_PLL_STATUS 0x0070 [ 0.270000] TX1 REGFILE [ 0.270000] PCIE_PHY_TX1_CTRL1 0x0009 [ 0.270000] PCIE_PHY_TX1_CTRL2 0x2e00 [ 0.270000] PCIE_PHY_TX1_CTRL3 0x1fff [ 0.270000] PCIE_PHY_TX1_A_CTRL1 0x0810 [ 0.270000] PCIE_PHY_TX1_A_CTRL2 0x0706 [ 0.270000] PCIE_PHY_TX1_MOD1 0x1ffe [ 0.270000] PCIE_PHY_TX1_MOD2 0xfffe [ 0.270000] PCIE_PHY_TX1_MOD3 0x0001 [ 0.270000] TX2 REGFILE [ 0.270000] PCIE_PHY_TX2_CTRL1 0x0009 [ 0.270000] PCIE_PHY_TX2_CTRL2 0x3096 [ 0.270000] PCIE_PHY_TX2_A_CTRL1 0x8010 [ 0.270000] PCIE_PHY_TX2_A_CTRL2 0x4707 [ 0.270000] PCIE_PHY_TX2_MOD1 0x1ffe [ 0.270000] PCIE_PHY_TX2_MOD2 0xfffe [ 0.270000] PCIE_PHY_TX2_MOD3 0x0001 [ 0.270000] RX1 REGFILE [ 0.270000] PCIE_PHY_RX1_CTRL1 0x0001 [ 0.270000] PCIE_PHY_RX1_CTRL2 0x3000 [ 0.270000] PCIE_PHY_RX1_CDR 0x0235 [ 0.270000] PCIE_PHY_RX1_EI 0x0004 [ 0.270000] PCIE_PHY_RX1_A_CTRL 0x6803 [ 0.870000] Lantiq PCIe Root Complex driver, version 2.0.0, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.920000] bio: create slab <bio-0> at 0 [ 0.920000] PCI host bridge to bus 0000:00 [ 0.930000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff] [ 0.930000] pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff] [ 0.940000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.950000] pci 0000:00:00.0: [1bef:0011] type 01 class 0x060000 [ 0.950000] ifx_pcie_rc_class_early_fixup port 0: fixed pcie host bridge to pci-pci bridge [ 0.960000] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.960000] pci 0000:01:00.0: [168c:abcd] type 00 class 0x020000 [ 0.960000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x0001ffff 64bit] [ 0.960000] pci 0000:01:00.0: reg 30: [mem 0x00000000-0x0000ffff pref] [ 0.960000] pci 0000:01:00.0: supports D1 [ 0.960000] pci 0000:01:00.0: PME# supported from D0 D1 D3hot [ 0.960000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.960000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 0.960000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff] [ 0.960000] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref] [ 0.970000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit] [ 0.970000] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref] [ 0.980000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.980000] pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff] [ 0.990000] pci 0000:00:00.0: bridge window [mem 0x1c100000-0x1c1fffff pref] [ 0.990000] NET: Registered protocol family 8 [ 1.000000] NET: Registered protocol family 20 [ 1.000000] Switching to clocksource MIPS [ 1.050000] NET: Registered protocol family 2 [ 1.050000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 1.060000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 1.060000] TCP: Hash tables configured (established 1024 bind 1024) [ 1.070000] TCP: reno registered [ 1.070000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 1.080000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 1.090000] avm_pa: try to activate hw accelaration for pid 1 (ipv4) [ 1.090000] NET: Registered protocol family 1 [ 1.100000] PCI: CLS 0 bytes, default 32 [ 1.100000] Lantiq CGU driver, version 1.1.32, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.120000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17, (c) 2009 Infineon Technologies AG skb_shared_size:184 [ 1.130000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.140000] fuse init (API version 7.22) [ 1.140000] yaffs: yaffs built Feb 8 2017 18:14:21 Installing. [ 1.140000] msgmni has been set to 209 [ 1.150000] io scheduler noop registered (default) [ 1.150000] [avm_membench_init] [ 1.490000] ttyS0 at MMIO 0x1e100c00 (irq = 107) is a PORT_IFX_ASC [ 1.500000] ifx_usif_uart_init: uart_register_driver failed [ 1.500000] avm_net_trace: Up and running. [ 1.510000] [loadcontrol] set auto - scale=1 [ 1.510000] [avm] configured: watchdog event debug [ 1.510000] AVM_WATCHDOG: Watchdog Driver for AR7 Hardware (Version 1.0, build: Feb 8 2017 18:14:21) [ 1.510000] Lantiq Thermal Sensor driver, version 1.0.3, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.520000] ifx_pmu_init: Major 244 [ 1.520000] Lantiq PMU driver, version 1.2.6, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.530000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.540000] Infineon Technologies RCU driver version 1.0.7 [ 1.560000] loop: module loaded [ 1.560000] nbd: registered device at major 43 [ 1.590000] Generic platform RAM MTD, (c) 2004 Simtec Electronics [ 1.590000] [HSNAND] Hardware-ECC activated [ 1.600000] ONFI param page 0 valid [ 1.600000] ONFI flash detected [ 1.600000] NAND device: Manufacturer ID: 0x2c, Chip ID: 0xf1 (Micron MT29F1G08ABADAWP), 128MiB, page size: 2048, OOB size: 64 [ 1.610000] Scanning device for bad blocks [ 1.710000] Creating 6 MTD partitions on "ifx_hsnand": [ 1.710000] 0x000000000000-0x000000400000 : "reserved-kernel" [ 1.720000] 0x000000400000-0x000003400000 : "reserved-filesystem" [ 1.730000] 0x000003400000-0x000003800000 : "kernel" [ 1.740000] 0x000003800000-0x000006800000 : "filesystem" [ 1.740000] 0x000006800000-0x000006a00000 : "config" [ 1.750000] 0x000006a00000-0x000008000000 : "nand-filesystem" [ 1.760000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_hsnand [ 1.770000] {ifx_sflash_setbaudrate} VR9 A21 high baudrate support [ 1.770000] SPI Device: MX25P2005 0xC2 (MX) 0x20 0x12 [ 1.770000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_sflash [ 1.770000] Creating 3 MTD partitions on "ifx_sflash": [ 1.780000] 0x000000000000-0x000000020000 : "urlader" [ 1.790000] 0x000000020000-0x000000030000 : "tffs (1)" [ 1.790000] 0x000000030000-0x000000040000 : "tffs (2)" [ 1.800000] Lantiq SPI flash driver, version 2.0.2, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.810000] tun: Universal TUN/TAP device driver, 1.6 [ 1.810000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.820000] IFX SWITCH API, Version 1.1.8.5 [ 1.820000] SWAPI: Registered character device [switch_api] with major no [81] [ 1.830000] Switch API: PCE MicroCode loaded !! [ 1.830000] i2c /dev entries driver [ 1.830000] cpuidle: using governor ladder [ 1.830000] cpuidle: using governor menu [ 1.840000] AVM PA for Linux 3.10.73 [ 1.840000] AVM PA skb pktinfo at offset 136 size 208 [ 1.850000] [loadcontrol]module avm_pa registered [ 1.850000] u32 classifier [ 1.850000] Performance counters on [ 1.860000] Actions configured [ 1.860000] ipip: IPv4 over IPv4 tunneling driver [ 1.870000] TCP: cubic registered [ 1.870000] NET: Registered protocol family 10 [ 1.870000] avm_pa: try to activate hw accelaration for pid 2 (ipv6) [ 1.880000] sit: IPv6 over IPv4 tunneling driver [ 1.890000] NET: Registered protocol family 17 [ 1.890000] Bridge broadcast ratelimiter registered [ 1.890000] KOAM is loaded successfully. [ 1.890000] l2tp_core: L2TP core driver, V2.0 [ 1.900000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 1.900000] l2tp_netlink: L2TP netlink interface [ 1.910000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 1.910000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 1.920000] 8021q: 802.1Q VLAN Support v1.8 [ 1.930000] Key type dns_resolver registered [ 1.930000] <ifx_fix_timing> [ 1.940000] [TFFS3_Init] No storage module registered, trying legacy fallback [ 1.940000] [TFFS3_Register_LGCY] Called [ 1.950000] [TFFS3_LGCY_Configure] Called [ 1.950000] [TFFS3_LGCY_Setup] using mtd7(tffs (1)), mtd8(tffs (2)) [ 1.960000] [TFFS3_LGCY_Setup] mtd "tffs (1)": segment value 4 [ 1.960000] [TFFS3_LGCY_Setup] mtd "tffs (2)": segment value 5 [ 1.970000] [TFFS3_LGCY_Setup] Using segment 5 (avail: 4 + 5) [ 1.970000] [TFFS3_LGCY_Setup] mtd8 size=0x10000 [ 1.980000] TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 3.0) [ 1.980000] [rescan_segment] Called with mode=2 [ 1.980000] TFFS: Clearing index for update [ 1.990000] Adam2 environment variables API installed. [ 2.000000] AVM Simple Profiling enabled Version 3.0 [ 2.000000] [simple-profiling]:2 performance counters implemented, NEW_34K [ 2.010000] [simple-profiling]Enable Performance Counter 0 for Data cache load/stores (User Supervisor Kernel Exception TC-ID=0) all cores tc: 0 [ 2.020000] [simple-profiling]Enable Performance Counter 1 for Data cache load/store misses (User Supervisor Kernel Exception TC-ID=0) all cores tc: 0 [ 2.030000] [simple-profiling]Enable Performance Counter 0 for Data cache load/stores (User Supervisor Kernel Exception TC-ID=1) all cores tc: 1 [ 2.050000] [simple-profiling]Enable Performance Counter 1 for Data cache load/store misses (User Supervisor Kernel Exception TC-ID=1) all cores tc: 1 [ 2.060000] [simple-profiling]Enable Performance Counter 0 for Main pipeline stalls (P) (User Supervisor Kernel Exception TC-ID=2) all cores tc: 2 [ 2.070000] [simple-profiling]Enable Performance Counter 1 for Cycles (P) (User Supervisor Kernel Exception TC-ID=2) all cores tc: 2 [ 2.080000] [simple-profiling]Enable Performance Counter 0 for Data cache load/stores (User Supervisor Kernel Exception TC-ID=3) all cores tc: 3 [ 2.100000] [simple-profiling]Enable Performance Counter 1 for Data cache load/store misses (User Supervisor Kernel Exception TC-ID=3) all cores tc: 3 [ 2.110000] [simple-profiling]all cores:performance-mode (round-robin): cpus on [ 2.120000] {avmnet_cfg_netinit} [ 2.120000] [avmnet] No config found for HWRev 177, HWSubRev 5, Profile-ID 0, trying base config for HWSubRev [ 2.130000] [avmnet] No config found for HWRev 177, HWSubRev 5, trying base config for HWRev [ 2.140000] [avmnet] [avmnet_swi_7port_init] Init on module swi_vr9 called. [ 2.600000] Loading AVM Net Common Datapath Driver for 7Port Switch...... [ 2.600000] [ppe_eth_init] init_hw() [ 2.600000] [init_hw] ppe_hw_init=0xff successful [ 2.610000] [ppe_eth_init] ifx_proc_file_create() [ 2.610000] [ppe_eth_init] dma_setup_init() [ 2.620000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown unicast frames 0x68 [ 2.630000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown multicast frames 0x68 [ 5.790000] avm_pa: try to activate hw accelaration for pid 1 (ipv4) [ 5.800000] avm_pa: tx channel activated, pid 1 (ipv4) [ 5.800000] avm_pa: try to activate hw accelaration for pid 2 (ipv6) [ 5.810000] avm_pa: tx channel activated, pid 2 (ipv6) [ 5.820000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth0): 5c:49:79:4d:a3:00 [ 5.830000] avmnet: avm_pa: register pid eth0 [ 5.830000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth1): 5c:49:79:4d:a3:01 [ 5.840000] avmnet: avm_pa: register pid eth1 [ 5.840000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth2): 5c:49:79:4d:a3:04 [ 5.850000] avmnet: avm_pa: register pid eth2 [ 5.850000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth3): 5c:49:79:4d:a3:05 [ 5.860000] avmnet: avm_pa: register pid eth3 [ 5.910000] SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock3 [ 5.920000] yaffs: dev is 32505859 name is "mtdblock3" ro [ 5.920000] yaffs: passed flags "" [ 5.930000] yaffs: yaffs: Attempting MTD mount of 31.3,"mtdblock3" [ 5.930000] yaffs: auto selecting yaffs2 [ 5.950000] yaffs: yaffs_read_super: is_checkpointed 1 [ 5.950000] VFS: Mounted root (yaffs filesystem) readonly on device 31:3. [ 5.960000] devtmpfs: mounted [ 5.960000] Freeing unused kernel memory: 292K (80857000 - 808a0000) [ 7.070000] TFFS Name Table L [ 7.210000] yaffs: dev is 32505860 name is "mtdblock4" rw [ 7.220000] yaffs: passed flags "" [ 7.220000] yaffs: yaffs: Attempting MTD mount of 31.4,"mtdblock4" [ 7.250000] yaffs: yaffs_read_super: is_checkpointed 0 [ 9.130000] led_modul_Fritz_Box_6840: module license '(C) Copyright 2012 by AVM' taints kernel. [ 9.140000] Disabling lock debugging due to kernel taint [ 9.150000] [module-alloc-by-name] give 0x1d000 bytes at 0x81105000 to module 'led_modul_Fritz_Box_6840' (0xcab000 bytes left) [ 9.170000] [LED] use GPIO 32 for 'gpio_avm_led_power' [ 9.180000] [LED] use GPIO 38 for 'gpio_avm_led_internet' [ 9.180000] [LED] use GPIO 35 for 'gpio_avm_led_dect' [ 9.190000] [LED] use GPIO 36 for 'gpio_avm_led_wlan' [ 9.190000] [LED] use GPIO 47 for 'gpio_avm_led_info' [ 9.200000] [LED] use GPIO 34 for 'gpio_avm_led_info_red' [ 9.200000] [BUTTON] use GPIO 29 for 'gpio_avm_button_wlan' [ 9.210000] [BUTTON] use GPIO 1 for 'gpio_avm_button_dect' [ 9.230000] AVM_WATCHDOG: System Init UEberwachung 120 Sekunden [ 9.630000] [module-alloc-by-name] give 0x3000 bytes at 0x81122000 to module 'rtc_avm' (0xca8000 bytes left) [ 9.650000] rtc-avm rtc-avm.0: rtc core: registered avm as rtc0 [ 9.650000] [avm-rtc]: avm_rtc_probe: register: ret=0x87711800 [ 9.660000] [avm-rtc]: avm_rtc_probe: success [ 9.850000] [avm_debug] redirecting kernel-messages (/dev/debug) [ 9.880000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x7d62) [ 9.880000] {micron_read_hwecc} page 0x7d62 Sec 0 1 Berr 0 OOB 0 ECC [ 9.910000] [module-alloc-by-name] give 0xe000 bytes at 0x81125000 to module 'Piglet_noemif' (0xc9a000 bytes left) [ 9.920000] [piglet]use settings for 177(1 gpio from hw_config) [ 10.020000] [piglet]patch_dectfw: c0165000, totallen = 48032(bba0) [ 10.020000] [piglet]patch_dectfw: patch_adress: a0 max_len: 26 with Version 2 Len: 17 [ 10.020000] [piglet]patch_dectfw: RFPI tag found 029663cf30 [ 10.030000] [piglet]patch_dectfw: dectmode 1 [ 10.030000] [piglet]dect_loader144xx: slow-bootmode [ 10.770000] system-load 6 loadavg 0.15 0.3 0.1 - 38 tasks:67 % curr:modprobe(7 %) max:init(36 %, pid:1) pgstat: sum=26387 free=22023 slab=2732 alloc=1718/s fault=2560/s (sleep 2) [ 10.850000] * [ 11.130000] ********************************************************************************************* [ 13.220000] [piglet]dect144xx_file_process: upload of '/lib/modules/dectfw_secondlevel_441.hex' successfull [ 15.330000] [piglet]TDM: FS: 8005 Hz CLK: 1023930 Hz [ 15.650000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x740c) [ 15.660000] {micron_read_hwecc} page 0x740c Sec 1 1 Berr 0 OOB 0 ECC [ 15.660000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x7415) [ 15.660000] {micron_read_hwecc} page 0x7415 Sec 1 1 Berr 0 OOB 0 ECC [ 15.810000] yaffs: dev is 32505861 name is "mtdblock5" rw [ 15.810000] yaffs: passed flags "" [ 15.810000] yaffs: yaffs: Attempting MTD mount of 31.5,"mtdblock5" [ 15.860000] yaffs: yaffs_read_super: is_checkpointed 0 [ 15.930000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x72c2) [ 15.930000] {micron_read_hwecc} page 0x72c2 Sec 2 1 Berr 0 OOB 0 ECC [ 16.190000] [module-alloc-by-name] give 0x75000 bytes at 0x81133000 to module 'pcmlink' (0xc25000 bytes left) [ 16.290000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x800b) [ 16.290000] {micron_read_hwecc} page 0x800b Sec 0 1 Berr 0 OOB 0 ECC [ 16.640000] [module-alloc-by-name] give 0xce000 bytes at 0x811a8000 to module 'isdn_fbox_fon5' (0xb57000 bytes left) [ 16.690000] [capi_oslib]avm_stack_attach: cpu1 -> cpu1 [ 16.690000] [pcmlink]chrony-support [ 16.710000] [isdn]PCMLINK: svnVersion: 2496 (isdn: 3215) Codecslots=6 Slics=1 Pots=1 TE=0 NT=0 DECT=4 (IA3222) no HwCross DSP-EC: 0 [ 17.130000] [module-alloc-by-name] give 0x69000 bytes at 0x81276000 to module 'capi_codec' (0xaee000 bytes left) [ 17.340000] [module-alloc-by-name] give 0x50000 bytes at 0x812df000 to module 'avm_dect' (0xa9e000 bytes left) [ 17.390000] [module-alloc-by-name] give 0x5000 bytes at 0x8132f000 to module 'dect_io' (0xa99000 bytes left) [ 17.390000] [DECTDRV_ERR] fpCap ext data queueSize 2560, avmTpui 4096/36865, etsiTpui 40961/0 [ 17.890000] udevd[1272]: starting version 175 [ 18.130000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x81fc) [ 18.130000] {micron_read_hwecc} page 0x81fc Sec 1 1 Berr 0 OOB 0 ECC [ 18.150000] [module-alloc-by-name] give 0x2000 bytes at 0x81334000 to module 'usb_common' (0xa97000 bytes left) [ 18.300000] [module-alloc-by-name] give 0x35000 bytes at 0x81336000 to module 'usbcore' (0xa62000 bytes left) [ 18.320000] usbcore: registered new interface driver usbfs [ 18.320000] usbcore: registered new interface driver hub [ 18.320000] usbcore: registered new device driver usb [ 18.540000] [module-alloc-by-name] give 0x21000 bytes at 0x8136b000 to module 'ltqusb_host' (0xa41000 bytes left) [ 18.560000] LTQUSB: ltqusb_hcd: version 4.0 B140513 [ 18.560000] LTQUSB: OPTION: __PHY_LONG_PREEMP__ [ 18.560000] LTQUSB: OPTION: __UNALIGNED_BUF_ADJ__ [ 18.560000] LTQUSB: OPTION: __NEW_COC__ [ 18.560000] LTQUSB: __INTRNAKRETRY__ [ 18.560000] LTQUSB: __INTRINCRETRY__ [ 18.560000] Chip Version :000b BurstSize=4 [ 18.950000] system-load 5 loadavg 0.22 0.5 0.2 - 53 tasks:13 % curr:modprobe(2 %) max:migration/1(7 %, pid:12) pgstat: sum=26249 free=19495 slab=3228 alloc=614/s fault=1064/s (sleep 1) [ 19.170000] LTQUSB: USB core #0 soft-reset [ 19.470000] LTQUSB: USB core #0 soft-reset [ 19.470000] hcd Prot1:60 079e 1950 Prot2:70 70000 SingleXact:0 [ 19.470000] LTQUSB: ltqhcd_init: req yield ret =9 [ 19.470000] lantiq,ltqusb lantiq,ltqusb: Lantiq USB Controller [ 19.470000] lantiq,ltqusb lantiq,ltqusb: new USB bus registered, assigned bus number 1 [ 19.470000] lantiq,ltqusb lantiq,ltqusb: irq 13, io mem 0xbe101000 [ 19.470000] LTQUSB: VBus1 registered IO#14 [ 19.470000] LTQUSB: Init: Power Port (0) [ 19.470000] LTQUSB: PORT POWER gpio = 14 on, delay 500ms [ 19.980000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 19.980000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 19.980000] usb usb1: Product: Lantiq USB Controller [ 19.980000] usb usb1: Manufacturer: Linux 3.10.73 ltqusb_hcd_1 [ 19.980000] usb usb1: SerialNumber: ltqusb_hcd_1 [ 19.980000] hub 1-0:1.0: USB hub found [ 19.980000] hub 1-0:1.0: 1 port detected [ 19.980000] avm_net_trace: New net trace device 'usb1' registered with minor 161. [ 20.490000] LTQUSB: USB core #1 soft-reset [ 20.800000] LTQUSB: USB core #1 soft-reset [ 20.800000] hcd Prot1:60 079e 1950 Prot2:70 70000 SingleXact:0 [ 20.800000] LTQUSB: ltqhcd_init: req yield ret =8 [ 20.800000] lantiq,ltqusb lantiq,ltqusb: Lantiq USB Controller [ 20.800000] lantiq,ltqusb lantiq,ltqusb: new USB bus registered, assigned bus number 2 [ 20.800000] lantiq,ltqusb lantiq,ltqusb: irq 14, io mem 0xbe106000 [ 20.800000] LTQUSB: VBus2 registered IO#5 [ 20.800000] LTQUSB: Init: Power Port (0) [ 20.800000] LTQUSB: PORT POWER gpio = 5 on, delay 500ms [ 21.310000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 [ 21.310000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 21.310000] usb usb2: Product: Lantiq USB Controller [ 21.310000] usb usb2: Manufacturer: Linux 3.10.73 ltqusb_hcd_2 [ 21.310000] usb usb2: SerialNumber: ltqusb_hcd_2 [ 21.320000] [sched_delayed] sched: RT throttling activated [ 21.320000] avm_net_trace: udev device avm_net_trace161 created [ 21.320000] hub 2-0:1.0: USB hub found [ 21.320000] hub 2-0:1.0: 1 port detected [ 21.320000] avm_net_trace: New net trace device 'usb2' registered with minor 162. [ 21.340000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x85c5) [ 21.340000] {micron_read_hwecc} page 0x85c5 Sec 1 1 Berr 0 OOB 0 ECC [ 21.400000] avm_net_trace: udev device avm_net_trace162 created [ 21.730000] usb 2-1: new high-speed USB device number 2 using lantiq,ltqusb [ 21.960000] usb 2-1: New USB device found, idVendor=216f, idProduct=0041 [ 21.960000] usb 2-1: New USB device strings: Mfr=3, Product=2, SerialNumber=4 [ 21.960000] usb 2-1: Product: Altair USB Product [ 21.960000] usb 2-1: Manufacturer: Altair [ 21.960000] usb 2-1: SerialNumber: F320AF3405497 [ 21.960000] Bus#2 connect: AVM Powermeter changed to 100 mA [ 21.970000] Bus#2 config: AVM Powermeter changed to 100 mA [ 22.690000] system-load 5 loadavg 0.60 0.13 0.4 - 65 tasks:33 % curr:udevd(1 %) max:watchdog/0(11 %, pid:10) pgstat: sum=26221 free=18130 slab=3534 alloc=649/s fault=744/s (sleep 3) [ 25.390000] [module-alloc-by-name] give 0x1cd000 bytes at 0x8138c000 to module 'kdsldmod' (0x874000 bytes left) [ 25.540000] kdsldmod: init start (Jun 1 2017 17:36:04) sizeof(struct sk_buff)=448 [ 25.550000] userman: device registerd (userman_url) with major=233 [ 25.550000] kdsld: ttychannel: ldisc 8 registered [ 25.550000] PCP_NL: PCP netlink interface (multicast group 1) [ 25.550000] kdsldmod: init done (Jun 1 2017 17:36:02) [ 28.430000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x8bca) [ 28.430000] {micron_read_hwecc} page 0x8bca Sec 0 1 Berr 0 OOB 0 ECC [ 29.600000] [avm_power] eth: port 0 force normal CON t0 [ 29.600000] [avm_power] eth: port 1 force throttle CON t0 [ 29.610000] [avm_power] eth: port 2 force throttle CON t0 [ 29.610000] [avm_power] eth: port 3 force throttle CON t0 [ 30.780000] IPv6: ADDRCONF(NETDEV_UP): lan: link is not ready [ 30.780000] IPv6: ADDRCONF(NETDEV_UP): lan: link is not ready [ 30.790000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 30.790000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 30.790000] IPv6: ADDRCONF(NETDEV_UP): eth2: link is not ready [ 30.800000] IPv6: ADDRCONF(NETDEV_UP): eth3: link is not ready [ 31.810000] IPv6: ADDRCONF(NETDEV_UP): guest: link is not ready [ 31.820000] IPv6: ADDRCONF(NETDEV_UP): guest: link is not ready [ 32.930000] system-load 100% loadavg 0.67 0.16 0.5 - 63 tasks:43 % curr:ctlmgr(15 %) max:ctlmgr(15 %, pid:2283) pgstat: sum=27441 free=12813 slab=4402 alloc=1940/s fault=3128/s (sleep 11) [ 34.420000] [module-alloc-by-name] give 0x27000 bytes at 0x81559000 to module 'aae' (0x84d000 bytes left) [ 34.480000] [wlan_config] Given config is: [ 34.480000] [wlan_config] hw_interface=0 chip_type=6 (osprey) offload=1 (non) [ 34.480000] [wlan_config] hwrev=177 hwsubrev=5 maca=5c:49:79:4d:a3:00 [ 34.480000] [wlan_eeprom] Calibration data blocks found = 1 [ 34.480000] [wlan_eeprom] EEPROM #1, type "AR93xx/AR95xx": [ 34.480000] [wlan_eeprom] Customer data="xb112-041-f0000" [ 34.480000] [wlan_eeprom] regDmn=0x8114 - patching to 0 [ 34.480000] [wlan_eeprom] MinCCAPwr thresh set to 2GHz:-70,-70,-70 5GHz:-1,0,0 [ 34.480000] [wlan_eeprom] Build with ART2 4.4 [ 34.480000] avm_net_trace: New net trace device 'WLAN Management Traffic' registered with minor 128. [ 34.490000] kdsld: kdsld_vcc_preunregister: * [ 34.490000] kdsld: nr_ipv4 0 nr_ipv6 0 nr_vpn 0 [ 34.500000] avm_net_trace: udev device avm_net_trace128 created [ 34.550000] kdsld: flushing internet sessions [ 34.740000] kdsld: kdsld_vcc_preregister: prelte1 [ 34.740000] kdsld: kdsld_vcc_preregister: vcc->ifaces= (null) [ 34.740000] kdsld: IPv6: internet: link local fe80::5e49:79ff:fe4d:a303 remote :: [ 34.740000] kdsld: internet: set_rcv_ipaddr: 192.168.178.1 [ 34.890000] [module-alloc-by-name] give 0x7000 bytes at 0x81580000 to module 'adf' (0x846000 bytes left) [ 34.910000] ****Address of trace_timer :81583100 [ 34.940000] system-load 3 loadavg 0.67 0.16 0.5 - 68 tasks:19 % curr:ctlmgr(6 %) max:ctlmgr(6 %, pid:2283) pgstat: sum=27635 free=11088 slab=4592 alloc=406/s fault=673/s (sleep 0) [ 34.990000] [module-alloc-by-name] give 0x4000 bytes at 0x81587000 to module 'asf' (0x842000 bytes left) [ 35.660000] [module-alloc-by-name] give 0xb7000 bytes at 0x8158b000 to module 'ath_hal' (0x78b000 bytes left) [ 35.680000] ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D) [ 35.740000] [module-alloc-by-name] give 0x9000 bytes at 0x81642000 to module 'ath_rate_atheros' (0x782000 bytes left) [ 35.750000] ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved [ 35.870000] [module-alloc-by-name] give 0xc000 bytes at 0x8164b000 to module 'ath_spectral' (0x776000 bytes left) [ 35.890000] ath_spectral: Version 2.0.0Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved [ 35.890000] SPECTRAL module built on Mar 1 2017 15:01:52 [ 35.960000] [module-alloc-by-name] give 0x14000 bytes at 0x81657000 to module 'ath_dfs' (0x762000 bytes left) [ 36.000000] ath_dfs: Version 2.0.0Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved [ 36.500000] [module-alloc-by-name] give 0x5f000 bytes at 0x8166b000 to module 'ath_dev' (0x703000 bytes left) [ 36.550000] ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 37.430000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x8fb0) [ 37.430000] {micron_read_hwecc} page 0x8fb0 Sec 2 1 Berr 0 OOB 0 ECC [ 38.250000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x8878) [ 38.250000] {micron_read_hwecc} page 0x8878 Sec 0 1 Berr 0 OOB 0 ECC [ 38.610000] [module-alloc-by-name] give 0x119000 bytes at 0x816ca000 to module 'umac' (0x5ea000 bytes left) [ 38.750000] ath_pci: SmartAntenna-DRT-0.1 (Atheros/multi-bss) [ 38.750000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002) [ 38.750000] __ath_attach: Set global_scn[0] [ 38.760000] ART Version : 72.117 SW Image Version : 0.41.24.0.0 Board Revision : [ 38.760000] ar9300_attach: nf_2_nom -110 nf_2_max -60 nf_2_min -125 [ 38.770000] SPECTRAL : get_capability not registered [ 38.770000] HAL_CAP_PHYDIAG : Capable [ 38.770000] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231) [ 38.770000] SPECTRAL : get_capability not registered [ 38.770000] HAL_CAP_RADAR : Capable [ 38.770000] SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 236) [ 38.770000] SPECTRAL : get_capability not registered [ 38.770000] HAL_CAP_SPECTRAL_SCAN : Capable [ 38.770000] SPECTRAL : get_tsf64 not registered [ 38.770000] spectral_init_netlink 83 NULL SKB [ 38.770000] SPECTRAL : No ADVANCED SPECTRAL SUPPORT [ 38.770000] SPECTRAL :----- module attached [ 38.770000] GreenAP on wifi%d: Attached [ 38.770000] ath_get_caps[6416] rx chainmask mismatch actual 7 sc_chainmak 0 [ 38.770000] ath_get_caps[6391] tx chainmask mismatch actual 7 sc_chainmak 0 [ 38.770000] ic_num_chains=3x3 [ 38.770000] _avm_ath_ext_attach_ah:169 [ 38.780000] band steering initialized for direct attach hardware [ 38.780000] ieee80211_bsteering_attach: Band steering initialized [ 38.780000] ath_attach_dfs[13067] dfsdomain 1 [ 38.790000] SPECTRAL : module already attached [ 38.790000] osif_wrap_attach:321 osif wrap attached [ 38.790000] osif_wrap_devt_init:946 osif wrap dev table init done [ 38.800000] request_irq type = 0x80 [ 38.860000] avm_net_trace: New net trace device 'HW (2.4 + 5 GHz, wifi0)' registered with minor 129. [ 38.860000] Register net trace device succeeded with minor 129 (wifi0). [ 38.860000] wifi0: Atheros ???: mem=0x1c000000, irq=138 hw_base=0xbc000000 [ 38.870000] _avm_ath_ext_attach_ieee:151 [ 38.920000] avm_net_trace: udev device avm_net_trace129 created [ 39.080000] [module-alloc-by-name] give 0x18000 bytes at 0x817e3000 to module 'userman_mod' (0x5d2000 bytes left) [ 39.110000] userman: LAN Client Internet-Accounting and Blocking [ 39.110000] userman: device registerd with major=231 [ 39.110000] userman: init ok [ 39.300000] [module-alloc-by-name] give 0x6000 bytes at 0x817fb000 to module 'ath_pktlog' (0x5cc000 bytes left) [ 39.590000] avm_pa: prioack enable [ 39.590000] avm_pa: prioack tgetenable [ 39.590000] avm_pa: priomap: not enough parameters [ 39.590000] avm_pa: priomap: not enough parameters [ 39.590000] avm_pa: priomap: not enough parameters [ 39.590000] avm_pa: priomap: not enough parameters [ 39.650000] [module-alloc-by-name] give 0x26000 bytes at 0x81801000 to module 'krtp' (0x5a6000 bytes left) [ 39.670000] krtp: rtp_fastpath_register done [ 39.680000] krtp: krtp_init done [ 39.680000] jitterbuffer_set_config: auto_on 1 ms 50 packets 0 [ 39.680000] avm_pa: telephony_reduce 65 [ 39.680000] avm_pa: mswin 300 400 [ 39.810000] [DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 255 -> 0 [ 39.830000] [DECTDRV_ERR] fpCap ext data queueSize 2560, avmTpui 4096/36865, etsiTpui 40961/0 [ 39.880000] [DECTDRV_ERR] fpCap ext data queueSize 2560, avmTpui 4096/36865, etsiTpui 40961/0 [ 40.590000] [DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 0 -> 0 [ 40.610000] [DECTDRV_ERR] fpCap ext data queueSize 2560, avmTpui 4096/36865, etsiTpui 40961/0 [ 40.640000] [module-alloc-by-name] give 0x4000 bytes at 0x81827000 to module 'ueservice' (0x5a2000 bytes left) [ 40.660000] usbcore: registered new interface driver ueservice [ 40.660000] [DECTDRV_ERR] API_FP_MAC_START_STOP_REQ 0 -> 0 [ 40.670000] [DECTDRV_ERR] fpCap ext data queueSize 2560, avmTpui 4096/36865, etsiTpui 40961/0 [ 40.760000] [module-alloc-by-name] give 0xa000 bytes at 0x8182b000 to module 'usbnet' (0x598000 bytes left) [ 40.840000] [module-alloc-by-name] give 0x4000 bytes at 0x81835000 to module 'cdc_ether' (0x594000 bytes left) [ 40.850000] usbcore: registered new interface driver cdc_ether [ 40.880000] [module-alloc-by-name] give 0x7000 bytes at 0x81839000 to module 'ue_lte' (0x58d000 bytes left) [ 40.920000] Send concat format change command: 4 chars, control msg returned 4 [ 40.930000] usbcore: registered new interface driver ue_altair [ 41.100000] LTQUSB: LTQUSB DEV 2 EP 83 HC 1 HALT [ 41.100000] LTQUSB: LTQUSB HC HALT 2 hcchar = 0x80989a00, hcint = 0x10, hcintmsk = 0x2, hctsiz = 0x40080200 [ 41.100000] LTQUSB: LTQUSB HC HALT 5 hcchar = 0xc0989a00, hcint = 0x0, hcintmsk = 0x2, hctsiz = 0x40080200 [ 41.100000] LTQUSB: LTQUSB HC HALT 5 after 0 iterations hcchar = 0x989a00, hcint = 0x2, hcintmsk = 0x2, hctsiz = 0x40080200 [ 41.100000] LTQUSB: LTQUSB DEV 2 EP 83 HC 1 Complete dequeueing urb 836da5c0, urbd 836dd880 [ 41.100000] LTQUSB: LTQUSB need_comp = 1 complete_inuse = 0 [ 41.130000] LTE_UDEV_TTY_ADD: LTE using /dev/ttyLTE0 as AT channel [ 41.170000] ath_attach_dfs[13067] dfsdomain 1 [ 41.250000] Requested VPA id 0 and MAC 5c:49:79:4d:a3:02 [ 41.260000] avm_net_trace: New net trace device 'AP (2.4 + 5 GHz, ath0)' registered with minor 131. [ 41.260000] Register vap net trace device succeeded with minor 131 (ath0). [ 41.260000] avm_net_trace: New net trace device 'AP (2.4 + 5 GHz, ath0)' registered with minor 132. [ 41.260000] Register vap net trace device succeeded with minor 132 (ath0). [ 41.260000] VAP device ath0 created osifp: (86fdac20) os_if: (834bc000) [ 41.330000] avm_net_trace: udev device avm_net_trace131 created [ 41.330000] LTE_UDEV_UESERVICE_ADD: Found Altair bootloader, running FWLoaderApp [ 41.350000] avm_net_trace: udev device avm_net_trace132 created [ 41.350000] ath0: registered PID at AVM_PA [ 41.350000] avm_pa: try to activate hw accelaration for pid 10 (ath0) [ 41.350000] avm_pa: rx channel activated, pid 10 (ath0) [ 41.350000] avm_pa: tx channel activated, pid 10 (ath0) [ 41.350000] ath0: registered VPID at AVM_PA [ 41.350000] DES SSID SET=FRITZ!Box 6840 LTE [ 41.350000] ACFG vendor param set fail, AVM mcast-to-ucast deactivated [ 41.480000] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 [ 41.520000] DEVICE IS DOWN ifname=ath0 [ 41.520000] DEVICE IS DOWN ifname=ath0 [ 41.780000] LTE using /usr/share/lte/image.bin. [ 42.200000] Warning: node not in table 0x857e2000 [ 42.360000] 8021q: adding VLAN 0 to HW filter on device ath0 [ 42.380000] IPv6: ADDRCONF(NETDEV_CHANGE): lan: link becomes ready [ 43.070000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x8d18) [ 43.070000] {micron_read_hwecc} page 0x8d18 Sec 3 1 Berr 0 OOB 0 ECC [ 43.080000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x8d2b) [ 43.080000] {micron_read_hwecc} page 0x8d2b Sec 3 1 Berr 0 OOB 0 ECC [ 45.130000] system-load 100% loadavg 1.57 0.37 0.12 - 95 tasks:85 % curr:pidof(0 %) max:kworker/1:1H(13 %, pid:1182) pgstat: sum=28610 free=5282 slab=6058 alloc=2265/s fault=3349/s (sleep 11) [ 45.320000] AVM_WATCHDOG: System Init UEberwachung abgeschlossen (84120 ms noch verfuegbar) [ 45.360000] [avm_power] pm_ressourceinfo_scriptparse: powerdevice_systemclock: norm_power_rate=100 act_rate=100 mul=0 div=1 offset=2000 NormP=2000 mW -> SumNormP=2000 mW [ 45.360000] [avm_power] pm_ressourceinfo_scriptparse: powerdevice_loadrate: norm_power_rate=100 act_rate=71 mul=15 div=1 offset=0 NormP=1500 mW -> SumNormP=3500 mW [ 45.360000] [avm_power] pm_ressourceinfo_scriptparse: powerdevice_cpuclock: norm_power_rate=100 act_rate=100 mul=0 div=1 offset=0 NormP=0 mW -> SumNormP=3500 mW [ 45.360000] [avm_power] pm_ressourceinfo_scriptparse: powerdevice_dspclock: norm_power_rate=100 act_rate=100 mul=0 div=1 offset=1000 NormP=1000 mW -> SumNormP=4500 mW [ 45.360000] [avm_power] pm_ressourceinfo_scriptparse: powerdevice_dect: norm_power_rate=100 act_rate=0 mul=200 div=78 offset=150 NormP=406 mW -> SumNormP=4906 mW [ 45.360000] [avm_power] pm_ressourceinfo_scriptparse: powerdevice_analog: norm_power_rate=100 act_rate=0 mul=141 div=10 offset=100 NormP=1510 mW -> SumNormP=6416 mW [ 45.360000] [avm_power] pm_ressourceinfo_scriptparse: powerdevice_usb_host: norm_power_rate=500 act_rate=0 mul=55 div=10 offset=0 NormP=2750 mW -> SumNormP=9166 mW [ 45.360000] [avm_power] pm_ressourceinfo_scriptparse: powerdevice_wlan: norm_power_rate=100 act_rate=0 mul=84 div=10 offset=100 NormP=940 mW -> SumNormP=10106 mW [ 45.360000] [avm_power] pm_ressourceinfo_scriptparse: powerdevice_lte: norm_power_rate=3400 act_rate=0 mul=1 div=1 offset=0 NormP=3400 mW -> SumNormP=13506 mW [ 45.360000] [avm_power] pm_ressourceinfo_scriptparse: powerdevice_ethernet: norm_power_rate=467 act_rate=9 mul=1 div=1 offset=50 NormP=517 mW -> SumNormP=14023 mW [ 45.360000] SysRq : Changing Loglevel [ 45.360000] Loglevel set to 4 [ 45.460000] ---> reanimated debugbuffer: read=0 write=16362, written=16362 <--- [ 45.840000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x8e96) [ 45.840000] {micron_read_hwecc} page 0x8e96 Sec 0 1 Berr 0 OOB 0 ECC [ 46.980000] Info: ltqhcd_hc_start() line 2257: ZLP write without short_rw set! xfer_count:0/0 [ 47.100000] LTQUSB: LTQUSB DEV 2 EP 83 HC 1 HALT [ 47.100000] LTQUSB: LTQUSB HC HALT 2 hcchar = 0x80989a00, hcint = 0x10, hcintmsk = 0x2, hctsiz = 0x40080200 [ 47.100000] LTQUSB: LTQUSB HC HALT 5 hcchar = 0xc0989a00, hcint = 0x0, hcintmsk = 0x2, hctsiz = 0x40080200 [ 47.100000] LTQUSB: LTQUSB HC HALT 5 after 0 iterations hcchar = 0x989a00, hcint = 0x2, hcintmsk = 0x2, hctsiz = 0x40080200 [ 47.100000] LTQUSB: LTQUSB DEV 2 EP 83 HC 1 Complete dequeueing urb 836da5c0, urbd 86ff0b40 [ 47.100000] LTQUSB: LTQUSB need_comp = 1 complete_inuse = 0 [ 47.100000] LTQUSB: ltqhcd_disconnect(81384198) [ 47.100000] LTQUSB: LTQUSB DEV 2 EP 82 HC 0 HALT [ 47.100000] LTQUSB: LTQUSB HC HALT 1 [ 47.100000] ue_altair 2-1:1.0: rx shutdown, code -143 [ 47.100000] LTQUSB: ltqhcd_urb_enqueue(): port not connected [ 47.100000] ue_altair 2-1:1.0: rx_submit: usb_submit_urb failed, device gone [ 47.100000] ue_altair 2-1:1.0: rx shutdown, code -143 [ 47.100000] LTQUSB: ltqhcd_urb_enqueue(): port not connected [ 47.100000] ue_altair 2-1:1.0: rx_submit: usb_submit_urb failed, device gone [ 47.100000] ue_altair 2-1:1.0: rx shutdown, code -143 [ 47.100000] LTQUSB: ltqhcd_urb_enqueue(): port not connected [ 47.100000] ue_altair 2-1:1.0: rx_submit: usb_submit_urb failed, device gone [ 47.100000] usb 2-1: USB disconnect, device number 2 [ 47.100000] Bus#2 disconnect: AVM Powermeter changed to 0 mA [ 47.100000] ALT3100_03_00_00_00_35_3B Loading Modules ended SUCCESSFULLY Status: OK [ 47.190000] LTE_UDEV_TTY_REM: Signal token missing, do nothing [ 47.650000] system-load 7 loadavg 1.77 0.43 0.14 - 95 tasks:7 % curr:ar7cfgctl(1 %) max:ar7cfgctl(1 %, pid:2732) pgstat: sum=28659 free=4385 slab=6030 alloc=476/s fault=851/s (sleep 0) [ 47.710000] usb 2-1: new high-speed USB device number 3 using lantiq,ltqusb [ 47.960000] usb 2-1: New USB device found, idVendor=216f, idProduct=0041 [ 47.960000] usb 2-1: New USB device strings: Mfr=3, Product=2, SerialNumber=4 [ 47.960000] usb 2-1: Product: Altair USB Product [ 47.960000] usb 2-1: Manufacturer: Altair [ 47.960000] usb 2-1: SerialNumber: F320AF3405497 [ 47.960000] Bus#2 connect: AVM Powermeter changed to 100 mA [ 47.960000] Spontaneous reconnect [ 47.970000] Bus#2 config: AVM Powermeter changed to 100 mA [ 48.120000] Send concat format change command: 4 chars, control msg returned 4 [ 48.140000] [ifx_hsnand_command] read block is critical (column: 0x0 page: 0x8661) [ 48.140000] {micron_read_hwecc} page 0x8661 Sec 2 0 Berr 0 OOB 1 ECC [ 48.170000] LTE_UDEV_TTY_ADD: LTE using /dev/ttyLTE0 as AT channel [ 48.420000] LTQUSB: LTQUSB DEV 3 EP 83 HC 1 HALT [ 48.420000] LTQUSB: LTQUSB HC HALT 2 hcchar = 0x80d89a00, hcint = 0x10, hcintmsk = 0x2, hctsiz = 0x40080200 [ 48.420000] LTQUSB: LTQUSB HC HALT 5 hcchar = 0xc0d89a00, hcint = 0x10, hcintmsk = 0x2, hctsiz = 0x40080200 [ 48.420000] LTQUSB: LTQUSB HC HALT 5 after 0 iterations hcchar = 0xd89a00, hcint = 0x12, hcintmsk = 0x2, hctsiz = 0x40080200 [ 48.420000] LTQUSB: LTQUSB DEV 3 EP 83 HC 1 Complete dequeueing urb 8363f140, urbd 837bd900 [ 48.420000] LTQUSB: LTQUSB need_comp = 1 complete_inuse = 0 [ 48.480000] LTE_UDEV_UESERVICE_ADD: Found Altair firmware, sending hw_add [ 49.050000] IPv6: ADDRCONF(NETDEV_UP): lte0: link is not ready [ 49.090000] IPv6: ADDRCONF(NETDEV_UP): lte1: link is not ready [ 49.110000] IPv6: ADDRCONF(NETDEV_UP): lte2: link is not ready [ 55.170000] system-load 100% loadavg 1.70 0.44 0.15 - 89 tasks:76 % curr:wland(34 %) max:wland(34 %, pid:2369) pgstat: sum=28853 free=3661 slab=6072 alloc=852/s fault=1304/s (sleep 7) [ 58.060000] GreenAP on wifi0: Transition to Power save (WAIT) [ 58.090000] 8021q: adding VLAN 0 to HW filter on device ath0 [ 238.560000] GreenAP on wifi0: Transition to power save On [ 3451.880000] system-load 100% loadavg 0.0 0.1 0.5 - 83 tasks:0 % curr:find(0 %) max:wland(0 %, pid:2369) pgstat: sum=28523 free=3294 slab=5838 alloc=15/s fault=0/s (sleep 6)