User Tools

Site Tools


toh:avm:fritz.box.wlan.3370

AVM FRITZ!Box WLAN 3370

FRITZ!Box WLAN 3370

Supported Versions

Hardware Highlights

ModelVersionSoCCPU CoresCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
FRITZ!Box WLAN 3370Lantiq XWAY VRX288500128NAND, 512NAND128Atheros AR9380b/g/na/n-4VDSL22x 2.0

Installation

Since commit 0b62fe5e OpenWrt can be installed using the EVA/Adam2 bootloader. Within the same HW revision 5 of the FRITZ!Box 3370 different NAND flash chips are used and the correct image has to be chosen.

Please read the detailed commit message before try install.

Box does not get bricked if false firmware is flashed → reboot loop → flash other NAND firmware version.

Micron MT29F1G08ABADA NAND flash chip on AVM FRITZ!Box WLAN 3370 → 128MB NAND Flash Memory

ST-Micro NAND04GW3B2DN6 NAND flash chip on AVM FRITZ!Box WLAN 3370 → 512MB NAND Flash Memory
(works with hynix-image)

Hynix HY27UF081G2M NAND chip on AVM FRITZ!Box WLAN 3370 → 128MB NAND Flash Memory

generic hints: install OpenWrtflashing via FTP

Flash Layout

First let's have a quick view at the Flash Layout with the stock firmware and after OpenWrt has been installed. When you later want to understand, what mtd/sysupgrade do, have a second look here:

Overview

FIXME

Installation LAN and serial (optional)

hints: EVA FTP install/recovery

connect host LAN cable to FritzBox LAN port and establish serial connection (optional) - see serial for further details

  1. set your host IP to 192.168.178.x (subnet 255.255.255.0)
  2. open a Terminal in the directory where the files to flash are
  3. power on FRITZ!Box
  4. establish an FTP connection within 5seconds to 192.168.178.1
    ftp -n 192.168.178.1

    or serial (optional): interrupt boot pressing a key, when Eva_AVM > appears in a Serial Port Terminal (e.g. GtkTerm opened as root user)

  5. issue the following FTP commands - :!: some boxes seem to reboot after 30s - see commit, so be quick → copy/paste f.e. with a Clipboard Manager → firmware flashing is done within a few seconds

If something goes wrong → do not panic → try again - bootloader is not touched.

ftp> quote USER adam2
ftp> quote PASS adam2
ftp> binary
ftp> debug
ftp> passive
ftp> quote SETENV linux_fs_start 0
ftp> quote MEDIA FLSH
ftp> put /path/to/openwrt-lantiq-xrx200-avm_fritz3370-rev2-micron-squashfs-eva-kernel.bin mtd1
ftp> put /path/to/openwrt-lantiq-xrx200-avm_fritz3370-rev2-micron-squashfs-eva-filesystem.bin mtd0
ftp> quote REBOOT
ftp> quit

This is printed:

vasilis74@devuan:~/FritzBox3370$ ftp -n 192.168.178.1
Connected to 192.168.178.1.
220 ADAM2 FTP Server ready
ftp> quote USER adam2
331 Password required for adam2
ftp> quote PASS adam2
230 User adam2 successfully logged in
ftp> binary
200 Type set to BINARY
ftp> debug
Debugging on (debug=1).
ftp> passive
Passive mode on.
ftp> quote SETENV linux_fs_start 0
---> SETENV linux_fs_start 0
200 SETENV command successful
ftp> quote MEDIA FLSH
---> MEDIA FLSH
200 Media set to MEDIA_FLASH
ftp> put /home/vasilis74/FritzBox3370/openwrt-19.07.0-lantiq-xrx200-avm_fritz3370-rev2-hynix-squashfs-eva-kernel.bin mtd1
local: /home/vasilis74/FritzBox3370/openwrt-19.07.0-lantiq-xrx200-avm_fritz3370-rev2-hynix-squashfs-eva-kernel.bin remote: mtd1
ftp: setsockopt (ignored): Permission denied
---> PASV
227 Entering Passive Mode (192,168,178,1,12,3)
---> STOR mtd1
150 Opening BINARY data connection
226 Transfer complete
2006235 bytes sent in 1.39 secs (1.3805 MB/s)
ftp> put /home/vasilis74/FritzBox3370/openwrt-19.07.0-lantiq-xrx200-avm_fritz3370-rev2-hynix-squashfs-eva-filesystem.bin mtd0
local: /home/vasilis74/FritzBox3370/openwrt-19.07.0-lantiq-xrx200-avm_fritz3370-rev2-hynix-squashfs-eva-filesystem.bin remote: mtd0
ftp: setsockopt (ignored): Permission denied
---> PASV
227 Entering Passive Mode (192,168,178,1,12,12)
---> STOR mtd0
150 Opening BINARY data connection
226 Transfer complete
4456448 bytes sent in 3.03 secs (1.4025 MB/s)
ftp> quote REBOOT
221 Thank you for using the FTP service on ADAM2
ftp> quit
221 Goodbye.

Upgrading OpenWrt

LuCI Web Upgrade Process

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

Terminal Upgrade Process

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There are two command line methods for upgrading:

  • sysupgrade
  • mtd

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
sysupgrade /tmp/xxx.abc

mtd

If sysupgrade does not support this router, use mtd.

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget http://downloads.openwrt.org/snapshots/trunk/XXX/xxx.abc
mtd write /tmp/xxx.abc firmware && reboot

Debricking

Failsafe mode

Basic configuration

After flashing, proceed with Basic configuration.
Set up your Internet connection, configure wireless, configure USB port, etc.

Hardware

Info

General
Brand AVM
Model FRITZ!Box WLAN 3370
Versions
Device Type WiFi Router
Availability Discontinued
Comments - general See also https://boxmatrix.info/wiki/FRITZ!Box_WLAN_3370 (old http://www.wehavemorefun.de/fritzbox/3370)
OpenWrt Support
Supported Since Commit https://git.lede-project.org/?p=source.git;a=commit;h=a57ffc09a766c5a05f47e60b3800bbf87ff8ac60
Supported Since Release 15.05
Supported Current Release 19.07.4
Unsupported
Hardware
Bootloader EVA
Target lantiq
System-On-Chip
CPU MHz 500
Flash MB 128NAND, 512NAND
RAM MB 128
Network
Ethernet 100M ports -
Ethernet Gbit ports 4
Switch Lantiq GSWIP (built-in SoC switch)
Modem VDSL2
VLAN ¿
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz a/n
WLAN Hardware Atheros AR9380
Detachable Antennas -
Comments - WLAN
Interfaces
USB ports 2x 2.0
SATA ports -
Serial Yes
JTAG Yes
Comments - USB & SATA ports
Misc
LED count 5
Button count 1
Power supply 12 VDC, 1.4 A
Links
Forum Topic URL
WikiDevi URL https://wikidevi.wi-cat.ru/AVM_FRITZ!Box_WLAN_3370
OEM device homepage URL
Firmware OEM Stock URL ftp://ftp.avm.de/archive/fritz.box/fritzbox.wlan_3370/firmware/
Firmware OpenWrt Install URL
Firmware OpenWrt Upgrade URL https://downloads.openwrt.org/releases/19.07.4/targets/lantiq/xrx200/
Edit the underlying data View/Edit data
Architecture MIPS32
Vendor Lantiq
Bootloader
System-On-Chip VR9: VRX288
CPU Cores 2
CPU MIPS 34Kc V1.2 2×500 Mhz
xDSL
VoIP
Flash-Chip
Flash size 256 KiB + 128/512MiB
RAM 128 MiB
Wireless AR9380
Switch Soc-integrated
DSL Lantiq VRX288 + VRX206
USB Yes 2 x 2.0
Serial Yes
JTAG Yes

Photos

Front:
FIXME Insert photo of front of the casing

Back:
FIXME Insert photo of back of the casing

Opening the case

Note: This will void your warranty!

Instructions found on BoxMatrix

  • Remove the 2 rubber stands close to the wallmount holes, they hide 2 of the screws
  • Open the 4 Torx 8 screws
  • Lift the casing top carefully, front hook easily breaks

Main PCB
AVM FRITZ!Box WLAN 3370 with Hynix HY27UF081G2M NAND chip

Serial

port.serial general information about the serial port, serial port cable, etc.
https://www.zebradem.com/wiki/index.php?title=Serielle_Konsole for information specific to Fritz!Boxes

How to connect to the Serial Port of this specific device:

Seen from the rear of the device, the most left of the 4 holes is square cut while the others are round.

Pin 1 [ ] 2 3 4
Function VCC RX TX GND

Serial connectors holes, rear side.

Serial connection with a MAX3232/RS232 TTL to Serial Port Converter.

Serial connection parameters
for FRITZ!Box WLAN 3370
115200, 8N1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to JTAG interface, and how to reflash the device with JTAG tools

How to connect to the JTAG Port of this specific device:
FIXME

Hardware mods

FriXtender - http://frixtender.de/

Bootlogs

OEM bootlog

ROM VER: 1.0.5 CFG 05 Initial DDR setting for SDRAM test pass Initial DDR check ok... [\] (AVM) EVA Revision: 1.1186 Version: 2186 (C) Copyright 2005 AVM Date: Apr 13 2011 Time: 14:46:06 (2) 2 0x0-0x741D [FLASH:] MACRONIX Uniform-Flash 256kB 256 Bytes WriteBuffer [FLASH:](Eraseregion [0] 4 sectors a 64kB) [NAND:] 128MB HYNIX 2048 Pagesize 128k Blocksize 1024 Blocks 8Bit 1 CS [SYSTEM:] VR9 on 500MHz/250MHz/250MHz .Infineon PHY11G detected Eva_AVM >.....................................................[] set PHYs in Reset 0x1 Lantiq xDSL CPE VR9 phym = 08000000, mem = 08000000, max_pfn = 00008000 Reserving memory for CP1 @0xa8000000, size 0x00000000 plat_device_tree_setup: AVM hardware subrevision 5 plat_device_tree_setup: using Fallback device-tree of AVM hardware subrevision 2 DT: d0 0d fe ed 00 00 09 61 [ 0.000000] Linux version 3.10.73 (jwetter@EmbeddedVM) (gcc version 4.8.3 (Buildroot 2014.08) ) #1 SMP Wed Aug 17 11:54:03 CEST 2016 [ 0.000000] [env_init] 0x8101a760[0] [ 0.000000] [env_init] 0x8101a7a0[1] [ 0.000000] [env_init] 0x8101a7e0[2] [ 0.000000] [env_init] switch to ram location [ 0.000000] [init_avm_kernel_config] AVM Kernel Config (ptr 80825000) [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: module memory entry [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: version info entry [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 0 found [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 1 found [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 2 found [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019555 (MIPS 34Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] [module-alloc] use 0xc90000 bytes at 0x81104000 [ 0.000000] PERCPU: Embedded 7 pages/cpu @81d98000 s7072 r8192 d13408 u32768 [ 0.000000] Kernel command line: console=ttyS0,115200n8r nor_size=0MB sflash_size=256KB nand_size=128MB ethaddr=24:65:11:6E:53:8E [ 0.000000] [NAND] nand_size = 0x8000000 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00000003 [ 0.000000] Readback ErrCtl register=00000003 [ 0.000000] Memory: 107752k/131072k available (5705k kernel code, 23320k reserved, 2690k data, 300k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:181 [ 0.000000] SRSConf0 0x3feffbfe: SRS1: 0xffffffff, SRS2 0xffffffff, SRS3 0xffffffff [ 0.000000] Lantiq ICU driver, version 3.0.1, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.020000] Calibrating delay loop... 331.77 BogoMIPS (lpj=1658880) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Security Framework initialized [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] CPU1 revision is: 00019555 (MIPS 34Kc) [ 0.170000] Brought up 2 CPUs [ 0.170000] [yield_context_init] cpu=1 tc=2 mask=300 [ 0.180000] [yield_context_init] cpu=0 tc=3 mask=410 [ 0.180000] devtmpfs: initialized [ 0.200000] pinctrl core: initialized pinctrl subsystem [ 0.200000] Creating Config Table [ 0.200000] [avm_generate_hw_config_table_from_device_tree] gpio_cnt: 21 [ 0.210000] NET: Registered protocol family 16 [ 0.220000] Reboot Status is: Short-PowerOff-Reboot [ 0.220000] [TFFS3_Early_Init] called [ 0.230000] [avmnet] [avmnet_cfg_init] Driver version: 6.221.2.4 - Revision 1496:3477 - Mi 17. Aug 11:53:18 CEST 2016 [ 0.850000] Lantiq PCIe Root Complex driver, version 2.0.0, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.900000] bio: create slab <bio-0> at 0 [ 0.900000] PCI host bridge to bus 0000:00 [ 0.910000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff] [ 0.910000] pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff] [ 0.920000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.930000] ifx_pcie_rc_class_early_fixup port 0: fixed pcie host bridge to pci-pci bridge [ 0.940000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff] [ 0.940000] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref] [ 0.950000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit] [ 0.960000] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref] [ 0.970000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.970000] pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff] [ 0.980000] pci 0000:00:00.0: bridge window [mem 0x1c100000-0x1c1fffff pref] [ 0.990000] NET: Registered protocol family 8 [ 0.990000] NET: Registered protocol family 20 [ 1.000000] Switching to clocksource MIPS [ 1.050000] NET: Registered protocol family 2 [ 1.050000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 1.060000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 1.060000] TCP: Hash tables configured (established 1024 bind 1024) [ 1.070000] TCP: reno registered [ 1.070000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 1.080000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 1.090000] NET: Registered protocol family 1 [ 1.090000] Lantiq CGU driver, version 1.1.32, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.110000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17, (c) 2009 Infineon Technologies AG [ 1.110000] skb_shared_size:184 [ 1.130000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.130000] fuse init (API version 7.22) [ 1.140000] msgmni has been set to 210 [ 1.140000] io scheduler noop registered (default) [ 1.480000] ttyS0 at MMIO 0x1e100c00 (irq = 107) is a PORT_IFX_ASC [ 1.490000] ifx_usif_uart_init: uart_register_driver failed [ 1.490000] avm_net_trace: Up and running. [ 1.500000] [loadcontrol] set auto - scale=1 [ 1.510000] ifx_pmu_init: Major 245 [ 1.510000] Lantiq PMU driver, version 1.2.6, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.520000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.520000] Infineon Technologies RCU driver version 1.0.7 [ 1.540000] loop: module loaded [ 1.550000] nbd: registered device at major 43 [ 1.570000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64 [ 1.590000] Scanning device for bad blocks [ 1.610000] Bad eraseblock 543 at 0x0000043e0000 [ 1.630000] badblock statistics: [ 1.630000] -------------------- [ 1.630000] start block = 0 [ 1.630000] num blocks = 1024 [ 1.630000] bad blocks = 1 [ 1.640000] [ 1.640000] >> The following table summarize all badblocks to visualize the distribution [ 1.640000] block [ start | count | size/kB ] (start block, number of blocks) [ 1.640000] --------------------------------- [ 1.660000] block [ 543 | 1 | 128 ] [ 1.670000] [ ======================= ] [ 1.670000] [ >> 1 | 128 ] [ 1.680000] Creating 6 MTD partitions on "ifx_nand": [ 1.680000] 0x000000000000-0x000000400000 : "kernel" [ 1.690000] 0x000000400000-0x000003400000 : "filesystem" [ 1.700000] 0x000003400000-0x000003800000 : "reserved-kernel" [ 1.710000] 0x000003800000-0x000006800000 : "reserved-filesystem" [ 1.710000] 0x000006800000-0x000006a00000 : "config" [ 1.720000] 0x000006a00000-0x000008000000 : "nand-filesystem" [ 1.730000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_nand [ 1.730000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_sflash [ 1.740000] Creating 3 MTD partitions on "ifx_sflash": [ 1.750000] 0x000000000000-0x000000020000 : "urlader" [ 1.760000] 0x000000020000-0x000000030000 : "tffs (1)" [ 1.760000] 0x000000030000-0x000000040000 : "tffs (2)" [ 1.770000] Lantiq SPI flash driver, version 2.0.1, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.780000] tun: Universal TUN/TAP device driver, 1.6 [ 1.780000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.790000] SWAPI: Registered character device [switch_api] with major no [81] [ 1.790000] i2c /dev entries driver [ 1.800000] cpuidle: using governor ladder [ 1.800000] cpuidle: using governor menu [ 1.810000] AVM PA 4.3.14 2015-10-21 [ 1.810000] AVM PA skb pktinfo at offset 136 size 196 [ 1.820000] [loadcontrol]module avm_pa registered [ 1.820000] ipip: IPv4 over IPv4 tunneling driver [ 1.830000] TCP: cubic registered [ 1.830000] NET: Registered protocol family 10 [ 1.830000] sit: IPv6 over IPv4 tunneling driver [ 1.840000] NET: Registered protocol family 17 [ 1.840000] l2tp_core: L2TP core driver, V2.0 [ 1.850000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 1.850000] l2tp_netlink: L2TP netlink interface [ 1.860000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 1.860000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 1.870000] 8021q: 802.1Q VLAN Support v1.8 [ 1.870000] Key type dns_resolver registered [ 1.880000] <ifx_fix_timing> [ 1.880000] [TFFS3_Init] No storage module registered, trying legacy fallback [ 1.890000] [TFFS3_Register_LGCY] Called [ 1.890000] [TFFS3_LGCY_Configure] Called [ 1.900000] [TFFS3_LGCY_Setup] using mtd7(tffs (1)), mtd8(tffs (2)) [ 1.900000] [TFFS3_LGCY_Setup] mtd "tffs (1)": segment value 2 [ 1.910000] [TFFS3_LGCY_Setup] mtd "tffs (2)": segment value 1 [ 1.920000] [TFFS3_LGCY_Setup] Using segment 2 (avail: 2 + 1) [ 1.920000] [TFFS3_LGCY_Setup] mtd7 size=0x10000 [ 1.930000] TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 3.0) [ 1.930000] [rescan_segment] Called with mode=2 [ 1.930000] TFFS: Clearing index for update [ 1.940000] Adam2 environment variables API installed. [ 1.950000] [simple-profiling]: 2 performance counters implemented, NEW_34K [ 1.950000] Enable Performance Counter 0 for Data cache load/stores (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 1.970000] Setup tcs=0x2 current_tc_mask=0x2, reg=0 [ 1.970000] [simple-profiling]: 2 performance counters implemented, NEW_34K [ 1.980000] Enable Performance Counter 1 for Data cache load/store misses (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 1.990000] Setup tcs=0x2 current_tc_mask=0x2, reg=1 [ 2.000000] {avmnet_cfg_netinit} [ 2.000000] [avmnet] No config found for HWRev 175, HWSubRev 5, Profile-ID 0, trying base config for HWSubRev [ 2.010000] [avmnet] No config found for HWRev 175, HWSubRev 5, trying base config for HWRev [ 2.020000] [avmnet] [avmnet_swi_7port_init] Init on module swi_vr9 called. [ 2.480000] [ppe_eth_init] init_hw() [ 2.480000] [init_hw] ppe_hw_init=0xff successful [ 2.490000] [ppe_eth_init] ifx_proc_file_create() [ 2.490000] [ppe_eth_init] dma_setup_init() [ 2.500000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown unicast frames 0x68 [ 2.510000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown multicast frames 0x68 [ 5.660000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth0): 24:65:11:6e:53:8e [ 5.670000] avmnet: avm_pa: register pid eth0 [ 5.670000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth1): 24:65:11:6e:53:8f [ 5.680000] avmnet: avm_pa: register pid eth1 [ 5.680000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth2): 24:65:11:6e:53:92 [ 5.690000] avmnet: avm_pa: register pid eth2 [ 5.700000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth3): 24:65:11:6e:53:93 [ 5.710000] avmnet: avm_pa: register pid eth3 [ 5.760000] SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock1 [ 5.760000] yaffs: dev is 32505857 name is "mtdblock1" ro [ 5.770000] yaffs: passed flags "" [ 5.790000] VFS: Mounted root (yaffs filesystem) readonly on device 31:1. [ 5.790000] devtmpfs: mounted [ 5.800000] Freeing unused kernel memory: 300K (80835000 - 80880000) [ 6.890000] TFFS Name Table L [ 7.000000] yaffs: dev is 32505860 name is "mtdblock4" rw [ 7.000000] yaffs: passed flags "" [ 8.680000] [avm_urlader_env_set_variable] opening ID 0x1ae for writing [ 8.790000] led_modul_Fritz_Box_3370: module license ' [ 8.790000] (C) Copyright 2012 by AVM [ 8.790000] ' taints kernel. [ 8.800000] Disabling lock debugging due to kernel taint [ 8.800000] [module-alloc-by-name] give 0x1a000 bytes at 0x81104000 to module 'led_modul_Fritz_Box_3370' (0xc76000 bytes left) [ 8.830000] [LED] use GPIO 32 for 'gpio_avm_led_power' [ 8.830000] [LED] use GPIO 38 for 'gpio_avm_led_lan_all' [ 8.840000] [LED] use GPIO 35 for 'gpio_avm_led_wlan' [ 8.840000] [LED] use GPIO 36 for 'gpio_avm_led_pppoe' [ 8.850000] [LED] use GPIO 47 for 'gpio_avm_led_info' [ 8.850000] [LED] use GPIO 34 for 'gpio_avm_led_info_red' [ 8.860000] [BUTTON] use GPIO 29 for 'gpio_avm_button_wlan' [ 8.860000] [BUTTON] use GPIO 1 for 'gpio_avm_button_power' [ 8.880000] AVM_WATCHDOG: System Init UEberwachung 120 Sekunden [ 9.380000] [module-alloc-by-name] give 0x3000 bytes at 0x8111e000 to module 'rtc_avm' (0xc73000 bytes left) [ 9.390000] rtc-avm rtc-avm.0: rtc core: registered avm as rtc0 [ 9.400000] [avm-rtc]: avm_rtc_probe: register: ret=0x87754000 [ 9.410000] [avm-rtc]: avm_rtc_probe: success [ 9.610000] [ 9.610000] [avm_debug] redirecting kernel-messages (/dev/debug)


OpenWrt snapshot 27.02.2020

[ 0.000000] Linux version 4.19.106 (builder@buildhost) (gcc version 8.3.0 (OpenWrt GCC 8.3.0 r12320-3660a89cb9)) #0 SMP Tue Feb 25 16:50:46 2020 [ 0.000000] SoC: xRX200 rev 1.2 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019556 (MIPS 34Kc) [ 0.000000] MIPS: machine is AVM FRITZ!Box 3370 Rev. 2 (Micron NAND) [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Detected 1 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] On node 0 totalpages: 32768 [ 0.000000] Normal zone: 288 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] random: get_random_bytes called from start_kernel+0x98/0x4e4 with crng_init=0 [ 0.000000] percpu: Embedded 14 pages/cpu s26288 r8192 d22864 u57344 [ 0.000000] pcpu-alloc: s26288 r8192 d22864 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 32480 [ 0.000000] Kernel command line: console=ttyLTQ0,115200 [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=00052940 [ 0.000000] Readback ErrCtl register=00052940 [ 0.000000] Memory: 121064K/131072K available (5354K kernel code, 221K rwdata, 1488K rodata, 1240K init, 233K bss, 10008K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 500MHz [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041786 ns [ 0.000011] sched_clock: 32 bits at 250MHz, resolution 4ns, wraps every 8589934590ns [ 0.007922] Calibrating delay loop... 332.54 BogoMIPS (lpj=665088) [ 0.046032] pid_max: default: 32768 minimum: 301 [ 0.051021] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.057531] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.068080] rcu: Hierarchical SRCU implementation. [ 0.074169] smp: Bringing up secondary CPUs ... [ 0.079845] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.079863] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.079992] CPU1 revision is: 00019556 (MIPS 34Kc) [ 0.110858] Synchronize counters for CPU 1: done. [ 0.135283] smp: Brought up 1 node, 2 CPUs [ 0.145544] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.155207] futex hash table entries: 512 (order: 2, 16384 bytes) [ 0.161669] pinctrl core: initialized pinctrl subsystem [ 0.169836] NET: Registered protocol family 16 [ 0.187961] dcdc-xrx200 1f106a00.dcdc: Core Voltage : 1016 mV [ 0.201235] pinctrl-xway 1e100b10.pinmux: Init done [ 0.207611] dma-xway 1e104100.dma: Init done - hw rev: 7, ports: 7, channels: 28 [ 0.331396] PCI host bridge /fpi@10000000/pcie@d900000 ranges: [ 0.373242] usbcore: registered new interface driver usbfs [ 0.378832] usbcore: registered new interface driver hub [ 0.384250] usbcore: registered new device driver usb [ 0.390053] PCI host bridge to bus 0000:00 [ 0.394067] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff] [ 0.401007] pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff] [ 0.407951] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.414794] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.422837] pci 0000:00:00.0: [1bef:0011] type 01 class 0x060000 [ 0.422868] ifx_pcie_rc_class_early_fixup: fixed pcie host bridge to pci-pci bridge [ 0.440628] pci 0000:00:00.0: ifx_pcie_rc_class_early_fixup+0x0/0x80 took 15625 usecs [ 0.448474] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.451836] pci 0000:01:00.0: [168c:abcd] type 00 class 0x020000 [ 0.451968] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0001ffff 64bit] [ 0.452082] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.452308] pci 0000:01:00.0: supports D1 [ 0.452412] pci 0000:01:00.0: PME# supported from D0 D1 D3hot [ 0.454508] random: fast init done [ 0.457854] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.457914] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 0.457986] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff] [ 0.464685] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref] [ 0.471984] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit] [ 0.479380] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref] [ 0.486642] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.491686] pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff] [ 0.498526] pci 0000:00:00.0: bridge window [mem 0x1c100000-0x1c1fffff pref] [ 0.508874] clocksource: Switched to clocksource MIPS [ 0.516626] NET: Registered protocol family 2 [ 0.522819] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes) [ 0.530537] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.537451] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 0.543875] TCP: Hash tables configured (established 1024 bind 1024) [ 0.550456] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.556255] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.562901] NET: Registered protocol family 1 [ 0.567283] PCI: CLS 0 bytes, default 32 [ 0.568146] gptu: totally 6 16-bit timers/counters [ 0.573163] gptu: misc_register on minor 63 [ 0.577333] gptu: succeeded to request irq 126 [ 0.581825] gptu: succeeded to request irq 127 [ 0.586338] gptu: succeeded to request irq 128 [ 0.590849] gptu: succeeded to request irq 129 [ 0.595367] gptu: succeeded to request irq 130 [ 0.599865] gptu: succeeded to request irq 131 [ 0.604587] No VPEs reserved for AP/SP, not initialize VPE loader [ 0.604587] Pass maxvpes=<n> argument as kernel argument [ 0.615972] No TCs reserved for AP/SP, not initializing RTLX. [ 0.615972] Pass maxtcs=<n> argument as kernel argument [ 0.629022] Crashlog allocated RAM at address 0x3f00000 [ 0.634776] workingset: timestamp_bits=14 max_order=15 bucket_order=1 [ 0.658314] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.664100] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.685015] io scheduler noop registered [ 0.688800] io scheduler deadline registered (default) [ 0.696949] ifx_pcie_bios_map_irq port 0 dev 0000:00:00.0 slot 0 pin 1 [ 0.703521] ifx_pcie_bios_map_irq dev 0000:00:00.0 irq 144 assigned [ 0.709849] pcieport 0000:00:00.0: enabling device (0000 -> 0002) [ 0.719830] 1e100c00.serial: ttyLTQ0 at MMIO 0x1e100c00 (irq = 112, base_baud = 0) is a lantiq,asc [ 0.728772] console [ttyLTQ0] enabled [ 0.736098] bootconsole [early0] disabled [ 0.748995] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xf1 [ 0.754021] nand: Micron MT29F1G08ABADAWP [ 0.757979] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.765578] Scanning device for bad blocks [ 0.842108] 2 fixed-partitions partitions found on MTD device 14000000.flash [ 0.847766] Creating 2 MTD partitions on "14000000.flash": [ 0.853262] 0x000000000000-0x000000400000 : "kernel" [ 0.860280] 0x000000400000-0x000008000000 : "ubi" [ 0.868657] spi-lantiq-ssc 1e100800.spi: Lantiq SSC SPI controller (Rev 8, TXFS 8, RXFS 8, DMA 1) [ 0.878730] m25p80 spi0.4: mx25l2005a (256 Kbytes) [ 0.882213] 3 fixed-partitions partitions found on MTD device spi0.4 [ 0.888506] Creating 3 MTD partitions on "spi0.4": [ 0.893283] 0x000000000000-0x000000020000 : "urlader" [ 0.900041] 0x000000020000-0x000000030000 : "tffs (1)" [ 0.905822] 0x000000030000-0x000000040000 : "tffs (2)" [ 0.915254] libphy: Fixed MDIO Bus: probed [ 0.923210] wdt 1f8803f0.watchdog: Init done [ 0.932665] NET: Registered protocol family 10 [ 0.941338] Segment Routing with IPv6 [ 0.943673] NET: Registered protocol family 17 [ 0.948177] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 0.961021] 8021q: 802.1Q VLAN Support v1.8 [ 1.076418] libphy: lantiq,xrx200-mdio: probed [ 1.085625] net-xrx200: invalid MAC, using random [ 1.089537] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.4 0:00: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.4] (mii_bus:phy_addr=0:00, irq=POLL) [ 1.103955] Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.4 0:01: attached PHY driver [Intel XWAY PHY11G (PEF 7071/PEF 7072) v1.4] (mii_bus:phy_addr=0:01, irq=POLL) [ 1.118199] Intel XWAY PHY11G (xRX v1.2 integrated) 0:11: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:11, irq=POLL) [ 1.131926] Intel XWAY PHY11G (xRX v1.2 integrated) 0:13: attached PHY driver [Intel XWAY PHY11G (xRX v1.2 integrated)] (mii_bus:phy_addr=0:13, irq=POLL) [ 1.148253] UBI: auto-attach mtd1 [ 1.150253] ubi0: attaching mtd1 [ 1.165934] UBI: EOF marker found, PEBs from 27 will be erased [ 1.172421] ubi0: scanning is finished [ 1.214503] ubi0: volume 1 ("rootfs_data") re-sized from 9 to 943 LEBs [ 1.221226] ubi0: attached mtd1 (name "ubi", size 124 MiB) [ 1.225343] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 129024 bytes [ 1.232201] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 512 [ 1.238905] ubi0: VID header offset: 512 (aligned 512), data offset: 2048 [ 1.245694] ubi0: good PEBs: 992, bad PEBs: 0, corrupted PEBs: 0 [ 1.251683] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 1.258917] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1582649446 [ 1.268052] ubi0: available PEBs: 0, total reserved PEBs: 992, PEBs reserved for bad PEB handling: 20 [ 1.277353] ubi0: background thread "ubi_bgt0d" started, PID 469 [ 1.281034] block ubiblock0_0: created from ubi0:0(rootfs) [ 1.288929] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 1.323684] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 1.333437] Freeing unused kernel memory: 1240K [ 1.336516] This architecture does not have kernel memory protection. [ 1.343052] Run /sbin/init as init process [ 2.482048] init: Console is alive [ 2.484386] init: - watchdog - [ 3.177174] lantiq,xrx200-net 1e108000.eth eth0: port 4 got link [ 3.704735] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.833697] dwc2 1e101000.usb: 1e101000.usb supply vusb_d not found, using dummy regulator [ 3.840985] dwc2 1e101000.usb: Linked as a consumer to regulator.0 [ 3.846767] dwc2 1e101000.usb: 1e101000.usb supply vusb_a not found, using dummy regulator [ 3.957403] dwc2 1e101000.usb: DWC OTG Controller [ 3.960740] dwc2 1e101000.usb: new USB bus registered, assigned bus number 1 [ 3.967849] dwc2 1e101000.usb: irq 62, io mem 0x1e101000 [ 3.973324] dwc2 1e101000.usb: Linked as a consumer to regulator.1 [ 3.980788] hub 1-0:1.0: USB hub found [ 3.983343] hub 1-0:1.0: 1 port detected [ 3.988675] dwc2 1e106000.usb: 1e106000.usb supply vusb_d not found, using dummy regulator [ 3.995825] dwc2 1e106000.usb: Linked as a consumer to regulator.0 [ 4.001785] dwc2 1e106000.usb: 1e106000.usb supply vusb_a not found, using dummy regulator [ 4.111246] dwc2 1e106000.usb: DWC OTG Controller [ 4.114642] dwc2 1e106000.usb: new USB bus registered, assigned bus number 2 [ 4.121654] dwc2 1e106000.usb: irq 91, io mem 0x1e106000 [ 4.127137] dwc2 1e106000.usb: Linked as a consumer to regulator.2 [ 4.134617] hub 2-0:1.0: USB hub found [ 4.137256] hub 2-0:1.0: 1 port detected [ 4.143607] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.160146] init: - preinit - [ 5.165362] random: procd: uninitialized urandom read (4 bytes read) [ 9.343681] UBIFS (ubi0:1): default file-system created [ 9.349131] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 556 [ 9.433146] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 9.439620] UBIFS (ubi0:1): LEB size: 129024 bytes (126 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 9.449528] UBIFS (ubi0:1): FS size: 120250368 bytes (114 MiB, 932 LEBs), journal size 6064128 bytes (5 MiB, 47 LEBs) [ 9.460144] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 9.466769] UBIFS (ubi0:1): media format: w4/r0 (latest is w5/r0), UUID 7B831E75-D433-4212-9F02-987F3DE3AE5A, small LPT model [ 9.480618] mount_root: overlay filesystem has not been fully initialized yet [ 9.487306] mount_root: switching to ubifs overlay [ 9.523137] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off. [ 9.536259] urandom-seed: Seed file not found (/etc/urandom.seed) [ 9.771479] procd: - early - [ 9.773294] procd: - watchdog - [ 10.248950] lantiq,xrx200-net 1e108000.eth eth0: port 4 lost link [ 10.467431] procd: - watchdog - [ 10.469870] procd: - ubus - [ 10.538522] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.544656] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.550500] random: ubusd: uninitialized urandom read (4 bytes read) [ 10.558509] procd: - init - [ 11.718383] kmodloader: loading kernel modules from /etc/modules.d/* [ 11.729165] IFXOS, Version 1.5.19 (c) Copyright 2009, Lantiq Deutschland GmbH [ 11.741848] NET: Registered protocol family 8 [ 11.744753] NET: Registered protocol family 20 [ 11.762814] PPP generic driver version 2.4.2 [ 11.820216] Lantiq (VRX) DSL CPE MEI driver, version 1.5.17.6, (c) 2007-2015 Lantiq Beteiligungs-GmbH & Co. KG [ 11.840185] [ 11.840185] [ 11.840185] Lantiq CPE API Driver version: DSL CPE API V4.17.18.6 [ 11.857929] [ 11.857929] Predefined debug level: 3 [ 11.873506] Loading modules backported from Linux version v5.4-rc8-0-gaf42d3466bdc [ 11.879718] Backport generated by backports.git v5.4-rc8-1-0-g368e8c51 [ 11.899466] Infineon Technologies DEU driver version 2.0.0 [ 11.907370] IFX DEU DES initialized (multiblock). [ 11.913382] IFX DEU AES initialized (multiblock). [ 11.921710] IFX DEU ARC4 initialized (multiblock). [ 11.925839] IFX DEU SHA1 initialized. [ 11.929354] IFX DEU MD5 initialized. [ 11.932807] IFX DEU SHA1_HMAC initialized. [ 11.937024] IFX DEU MD5_HMAC initialized. [ 11.954767] NET: Registered protocol family 24 [ 11.975876] xt_time: kernel timezone is -0000 [ 12.201355] ifx_pcie_bios_map_irq port 0 dev 0000:01:00.0 slot 0 pin 1 [ 12.206630] ifx_pcie_bios_map_irq dev 0000:01:00.0 irq 144 assigned [ 12.212951] ath9k 0000:01:00.0: enabling device (0000 -> 0002) [ 12.219696] ath9k 0000:01:00.0: Direct firmware load for ath9k-eeprom-pci-0000:01:00.0.bin failed with error -2 [ 12.228906] ath9k 0000:01:00.0: Falling back to syfs fallback for: ath9k-eeprom-pci-0000:01:00.0.bin [ 12.327474] urngd: v1.0.2 started. [ 12.967147] random: crng init done [ 12.969206] random: 6 urandom warning(s) missed due to ratelimiting [ 13.699846] ath: EEPROM regdomain: 0x8114 [ 13.699864] ath: EEPROM indicates we should expect a country code [ 13.699877] ath: doing EEPROM country->regdmn map search [ 13.699889] ath: country maps to regdmn code: 0x37 [ 13.699902] ath: Country alpha2 being used: DE [ 13.699911] ath: Regpair used: 0x37 [ 13.717682] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 13.722003] ieee80211 phy0: Atheros AR9300 Rev:3 mem=0xbc000000, irq=144 [ 13.731864] kmodloader: done loading kernel modules from /etc/modules.d/* [ 39.019811] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 39.045675] device eth0 entered promiscuous mode [ 39.057775] br-lan: port 1(eth0.1) entered blocking state [ 39.061984] br-lan: port 1(eth0.1) entered disabled state [ 39.068111] device eth0.1 entered promiscuous mode [ 39.095548] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 41.065386] lantiq,xrx200-net 1e108000.eth eth0: port 4 got link [ 41.070240] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 41.100596] br-lan: port 1(eth0.1) entered blocking state [ 41.104830] br-lan: port 1(eth0.1) entered forwarding state [ 41.124475] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready BusyBox v1.31.1 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r12320-3660a89cb9 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:~#


OpenWRT->AVMrecovery

Runnig the .exe found at AVM's server ftp://ftp.avm.de/archive/fritz.box/fritzbox.wlan_3370/x_misc/english/ in a Windows machine (if you have one), setting: a static IP 192.168.178.2 , Subnet Mask 255.255.255.0 , Gateway 192.168.178.1

ROM VER: 1.0.5 CFG 05 Initial DDR setting for SDRAM test pass Initial DDR check ok... [/] (AVM) EVA Revision: 1.1186 Version: 2186 (C) Copyright 2005 AVM Date: Apr 13 2011 Time: 14:46:06 (2) 2 0x0-0x741D [FLASH:] MACRONIX Uniform-Flash 256kB 256 Bytes WriteBuffer [FLASH:](Eraseregion [0] 4 sectors a 64kB) [NAND:] 128MB HYNIX 2048 Pagesize 128k Blocksize 1024 Blocks 8Bit 1 CS [SYSTEM:] VR9 on 500MHz/250MHz/250MHz .Infineon PHY11G detected Eva_AVM > . Eva_AVM > flash . . Eva_AVM > flash . .....................................................[] set PHYs in Reset 0x1 Lantiq xDSL CPE VR9 phym = 06b9bf00, mem = 06b9bf00, max_pfn = 00006b9b Reserving memory for CP1 @0xa6b9bf00, size 0x00000000 plat_device_tree_setup: AVM hardware subrevision 5 plat_device_tree_setup: using Fallback device-tree of AVM hardware subrevision 2 DT: d0 0d fe ed 00 00 09 61 [ 0.000000] Linux version 3.10.73 (jwetter@EmbeddedVM) (gcc version 4.8.3 (Buildroot 2014.08) ) #1 SMP Wed Aug 17 11:54:03 CEST 2016 [ 0.000000] [env_init] 0x8101a760[0] [ 0.000000] [env_init] 0x8101a7a0[1] [ 0.000000] [env_init] 0x8101a7e0[2] [ 0.000000] [env_init] switch to ram location [ 0.000000] [init_avm_kernel_config] AVM Kernel Config (ptr 80825000) [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: module memory entry [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: version info entry [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 0 found [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 1 found [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 2 found [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019555 (MIPS 34Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 06b9bf00 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] [module-alloc] use 0xc90000 bytes at 0x810dc000 [ 0.000000] PERCPU: Embedded 7 pages/cpu @81d70000 s7072 r8192 d13408 u32768 [ 0.000000] Kernel command line: mtdram1=0x86b9bf00,0x88000000 console=ttyS0,115200n8r nor_size=0MB sflash_size=256KB nand_size=128MB ethaddr=24:65:11:6E:53:8E [ 0.000000] [mtdram_setup] mtdram1 0x06b9bf00-0x07ffffff [ 0.000000] [NAND] nand_size = 0x8000000 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=0007e2b1 [ 0.000000] Readback ErrCtl register=0007e2b1 [ 0.000000] Memory: 87028k/110188k available (5705k kernel code, 23160k reserved, 2690k data, 300k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:181 [ 0.000000] SRSConf0 0x3feffbfe: SRS1: 0xffffffff, SRS2 0xffffffff, SRS3 0xffffffff [ 0.000000] Lantiq ICU driver, version 3.0.1, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.020000] Calibrating delay loop... 331.77 BogoMIPS (lpj=1658880) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Security Framework initialized [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] CPU1 revision is: 00019555 (MIPS 34Kc) [ 0.170000] Brought up 2 CPUs [ 0.170000] [yield_context_init] cpu=1 tc=2 mask=300 [ 0.180000] [yield_context_init] cpu=0 tc=3 mask=410 [ 0.180000] devtmpfs: initialized [ 0.200000] pinctrl core: initialized pinctrl subsystem [ 0.200000] Creating Config Table [ 0.200000] [avm_generate_hw_config_table_from_device_tree] gpio_cnt: 21 [ 0.210000] NET: Registered protocol family 16 [ 0.220000] Reboot Status is: Power-On [ 0.220000] [TFFS3_Early_Init] called [ 0.230000] [avmnet] [avmnet_cfg_init] Driver version: 6.221.2.4 - Revision 1496:3477 - Mi 17. Aug 11:53:18 CEST 2016 [ 0.850000] Lantiq PCIe Root Complex driver, version 2.0.0, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.900000] bio: create slab <bio-0> at 0 [ 0.900000] PCI host bridge to bus 0000:00 [ 0.910000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff] [ 0.910000] pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff] [ 0.920000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.930000] ifx_pcie_rc_class_early_fixup port 0: fixed pcie host bridge to pci-pci bridge [ 0.940000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff] [ 0.940000] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref] [ 0.950000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit] [ 0.950000] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref] [ 0.960000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.960000] pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff] [ 0.970000] pci 0000:00:00.0: bridge window [mem 0x1c100000-0x1c1fffff pref] [ 0.970000] NET: Registered protocol family 8 [ 0.980000] NET: Registered protocol family 20 [ 0.980000] Switching to clocksource MIPS [ 1.030000] NET: Registered protocol family 2 [ 1.030000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 1.040000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 1.040000] TCP: Hash tables configured (established 1024 bind 1024) [ 1.050000] TCP: reno registered [ 1.050000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 1.060000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 1.070000] NET: Registered protocol family 1 [ 1.070000] Lantiq CGU driver, version 1.1.32, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.090000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17, (c) 2009 Infineon Technologies AG [ 1.090000] skb_shared_size:184 [ 1.110000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.110000] fuse init (API version 7.22) [ 1.120000] msgmni has been set to 169 [ 1.120000] io scheduler noop registered (default) [ 1.460000] ttyS0 at MMIO 0x1e100c00 (irq = 107) is a PORT_IFX_ASC [ 1.460000] ifx_usif_uart_init: uart_register_driver failed [ 1.470000] avm_net_trace: Up and running. [ 1.470000] [loadcontrol] set auto - scale=1 [ 1.480000] ifx_pmu_init: Major 245 [ 1.480000] Lantiq PMU driver, version 1.2.6, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.490000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.500000] Infineon Technologies RCU driver version 1.0.7 [ 1.520000] loop: module loaded [ 1.520000] nbd: registered device at major 43 [ 1.550000] [ifx_jffs2_parser_function] exit on mtd ram-filesystem [ 1.560000] [ifx_ext2fs_parser_function] found partition @pos 0x264200 [ 1.570000] 2 find_ext2fs partitions found on MTD device ram-filesystem [ 1.570000] Creating 2 MTD partitions on "ram-filesystem": [ 1.580000] 0x000000264200-0x000001464100 : "rootfs_ram" [ 1.590000] 0x000000000000-0x000000264200 : "kernel_ram" [ 1.590000] mtd-ram mtd-ram: registered mtd device [ 1.600000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64 [ 1.610000] Scanning device for bad blocks [ 1.630000] Bad eraseblock 543 at 0x0000043e0000 [ 1.650000] badblock statistics: [ 1.650000] -------------------- [ 1.650000] start block = 0 [ 1.650000] num blocks = 1024 [ 1.650000] bad blocks = 1 [ 1.670000] [ 1.670000] >> The following table summarize all badblocks to visualize the distribution [ 1.670000] block [ start | count | size/kB ] (start block, number of blocks) [ 1.670000] --------------------------------- [ 1.690000] block [ 543 | 1 | 128 ] [ 1.700000] [ ======================= ] [ 1.700000] [ >> 1 | 128 ] [ 1.700000] Creating 6 MTD partitions on "ifx_nand": [ 1.710000] 0x000000000000-0x000000400000 : "kernel" [ 1.720000] 0x000000400000-0x000003400000 : "filesystem" [ 1.720000] 0x000003400000-0x000003800000 : "reserved-kernel" [ 1.730000] 0x000003800000-0x000006800000 : "reserved-filesystem" [ 1.740000] 0x000006800000-0x000006a00000 : "config" [ 1.750000] 0x000006a00000-0x000008000000 : "nand-filesystem" [ 1.750000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_nand [ 1.760000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_sflash [ 1.770000] Creating 3 MTD partitions on "ifx_sflash": [ 1.770000] 0x000000000000-0x000000020000 : "urlader" [ 1.780000] 0x000000020000-0x000000030000 : "tffs (1)" [ 1.790000] 0x000000030000-0x000000040000 : "tffs (2)" [ 1.790000] Lantiq SPI flash driver, version 2.0.1, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.800000] tun: Universal TUN/TAP device driver, 1.6 [ 1.810000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.810000] SWAPI: Registered character device [switch_api] with major no [81] [ 1.820000] i2c /dev entries driver [ 1.820000] cpuidle: using governor ladder [ 1.830000] cpuidle: using governor menu [ 1.830000] AVM PA 4.3.14 2015-10-21 [ 1.830000] AVM PA skb pktinfo at offset 136 size 196 [ 1.840000] [loadcontrol]module avm_pa registered [ 1.840000] ipip: IPv4 over IPv4 tunneling driver [ 1.850000] TCP: cubic registered [ 1.850000] NET: Registered protocol family 10 [ 1.860000] sit: IPv6 over IPv4 tunneling driver [ 1.860000] NET: Registered protocol family 17 [ 1.870000] l2tp_core: L2TP core driver, V2.0 [ 1.870000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 1.880000] l2tp_netlink: L2TP netlink interface [ 1.880000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 1.890000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 1.890000] 8021q: 802.1Q VLAN Support v1.8 [ 1.900000] Key type dns_resolver registered [ 1.900000] <ifx_fix_timing> [ 1.910000] [TFFS3_Init] No storage module registered, trying legacy fallback [ 1.910000] [TFFS3_Register_LGCY] Called [ 1.920000] [TFFS3_LGCY_Configure] Called [ 1.920000] [TFFS3_LGCY_Setup] using mtd10(tffs (1)), mtd11(tffs (2)) [ 1.930000] [TFFS3_LGCY_Setup] mtd "tffs (1)": segment value 1 [ 1.930000] [TFFS3_LGCY_Setup] mtd "tffs (2)": segment value 1 [ 1.940000] [TFFS3_LGCY_Setup] Using segment 1 (avail: 1 + 1) [ 1.950000] [TFFS3_LGCY_Setup] mtd11 size=0x10000 [ 1.950000] TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 3.0) [ 1.950000] [rescan_segment] Called with mode=2 [ 1.950000] TFFS: Clearing index for update [ 1.970000] Adam2 environment variables API installed. [ 1.970000] [simple-profiling]: 2 performance counters implemented, NEW_34K [ 1.980000] Enable Performance Counter 0 for Data cache load/stores (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 1.990000] Setup tcs=0x2 current_tc_mask=0x2, reg=0 [ 2.000000] [simple-profiling]: 2 performance counters implemented, NEW_34K [ 2.000000] Enable Performance Counter 1 for Data cache load/store misses (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 2.020000] Setup tcs=0x2 current_tc_mask=0x2, reg=1 [ 2.030000] {avmnet_cfg_netinit} [ 2.030000] [avmnet] No config found for HWRev 175, HWSubRev 5, Profile-ID 0, trying base config for HWSubRev [ 2.040000] [avmnet] No config found for HWRev 175, HWSubRev 5, trying base config for HWRev [ 2.050000] [avmnet] [avmnet_swi_7port_init] Init on module swi_vr9 called. [ 2.510000] [ppe_eth_init] init_hw() [ 2.510000] [init_hw] ppe_hw_init=0xff successful [ 2.510000] [ppe_eth_init] ifx_proc_file_create() [ 2.520000] [ppe_eth_init] dma_setup_init() [ 2.520000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown unicast frames 0x68 [ 2.530000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown multicast frames 0x68 [ 5.700000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth0): 24:65:11:6e:53:8e [ 5.710000] avmnet: avm_pa: register pid eth0 [ 5.710000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth1): 24:65:11:6e:53:8f [ 5.720000] avmnet: avm_pa: register pid eth1 [ 5.730000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth2): 24:65:11:6e:53:92 [ 5.740000] avmnet: avm_pa: register pid eth2 [ 5.740000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth3): 24:65:11:6e:53:93 [ 5.750000] avmnet: avm_pa: register pid eth3 [ 5.800000] VFS: Mounted root (ext2 filesystem) readonly on device 31:0. [ 5.800000] devtmpfs: mounted [ 5.810000] Freeing unused kernel memory: 300K (80835000 - 80880000) [ 6.560000] led_modul_Fritz_Box_3370: module license ' [ 6.560000] (C) Copyright 2012 by AVM [ 6.560000] ' taints kernel. [ 6.570000] Disabling lock debugging due to kernel taint [ 6.580000] [module-alloc-by-name] give 0x1a000 bytes at 0x810dc000 to module 'led_modul_Fritz_Box_3370' (0xc76000 bytes left) [ 6.600000] [LED] use GPIO 32 for 'gpio_avm_led_power' [ 6.600000] [LED] use GPIO 38 for 'gpio_avm_led_lan_all' [ 6.610000] [LED] use GPIO 35 for 'gpio_avm_led_wlan' [ 6.610000] [LED] use GPIO 36 for 'gpio_avm_led_pppoe' [ 6.620000] [LED] use GPIO 47 for 'gpio_avm_led_info' [ 6.620000] [LED] use GPIO 34 for 'gpio_avm_led_info_red' [ 6.630000] [BUTTON] use GPIO 29 for 'gpio_avm_button_wlan' [ 6.630000] [BUTTON] use GPIO 1 for 'gpio_avm_button_power' [ 8.310000] yaffs: dev is 32505860 name is "mtdblock4" rw [ 8.310000] yaffs: passed flags "" [ 12.670000] TFFS Name Table L [ 12.680000] [avm_urlader_env_set_variable] opening ID 0x1aa for writing [ 25.280000] Res ROM VER: 1.0.5 CFG 05 Initial DDR setting for SDRAM test pass Initial DDR check ok... [\] (AVM) EVA Revision: 1.1186 Version: 2186 (C) Copyright 2005 AVM Date: Apr 13 2011 Time: 14:46:06 (2) 2 0x0-0x741D [FLASH:] MACRONIX Uniform-Flash 256kB 256 Bytes WriteBuffer [FLASH:](Eraseregion [0] 4 sectors a 64kB) [NAND:] 128MB HYNIX 2048 Pagesize 128k Blocksize 1024 Blocks 8Bit 1 CS [SYSTEM:] VR9 on 500MHz/250MHz/250MHz .Infineon PHY11G detected Eva_AVM >.....................................................[] set PHYs in Reset 0x1 Lantiq xDSL CPE VR9 phym = 08000000, mem = 08000000, max_pfn = 00008000 Reserving memory for CP1 @0xa8000000, size 0x00000000 plat_device_tree_setup: AVM hardware subrevision 5 plat_device_tree_setup: using Fallback device-tree of AVM hardware subrevision 2 DT: d0 0d fe ed 00 00 09 61 [ 0.000000] Linux version 3.10.73 (jwetter@EmbeddedVM) (gcc version 4.8.3 (Buildroot 2014.08) ) #1 SMP Wed Aug 17 11:54:03 CEST 2016 [ 0.000000] [env_init] 0x8101a760[0] [ 0.000000] [env_init] 0x8101a7a0[1] [ 0.000000] [env_init] 0x8101a7e0[2] [ 0.000000] [env_init] switch to ram location [ 0.000000] [init_avm_kernel_config] AVM Kernel Config (ptr 80825000) [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: module memory entry [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: version info entry [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 0 found [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 1 found [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 2 found [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019555 (MIPS 34Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] [module-alloc] use 0xc90000 bytes at 0x81104000 [ 0.000000] PERCPU: Embedded 7 pages/cpu @81d98000 s7072 r8192 d13408 u32768 [ 0.000000] Kernel command line: console=ttyS0,115200n8r nor_size=0MB sflash_size=256KB nand_size=128MB ethaddr=24:65:11:6E:53:8E [ 0.000000] [NAND] nand_size = 0x8000000 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=0007e2b0 [ 0.000000] Readback ErrCtl register=0007e2b0 [ 0.000000] Memory: 107752k/131072k available (5705k kernel code, 23320k reserved, 2690k data, 300k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:181 [ 0.000000] SRSConf0 0x3feffbfe: SRS1: 0xffffffff, SRS2 0xffffffff, SRS3 0xffffffff [ 0.000000] Lantiq ICU driver, version 3.0.1, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.020000] Calibrating delay loop... 331.77 BogoMIPS (lpj=1658880) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Security Framework initialized [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] CPU1 revision is: 00019555 (MIPS 34Kc) [ 0.170000] Brought up 2 CPUs [ 0.170000] [yield_context_init] cpu=1 tc=2 mask=300 [ 0.180000] [yield_context_init] cpu=0 tc=3 mask=410 [ 0.180000] devtmpfs: initialized [ 0.200000] pinctrl core: initialized pinctrl subsystem [ 0.200000] Creating Config Table [ 0.200000] [avm_generate_hw_config_table_from_device_tree] gpio_cnt: 21 [ 0.210000] NET: Registered protocol family 16 [ 0.220000] Reboot Status is: Soft-Reboot [ 0.220000] [TFFS3_Early_Init] called [ 0.230000] [avmnet] [avmnet_cfg_init] Driver version: 6.221.2.4 - Revision 1496:3477 - Mi 17. Aug 11:53:18 CEST 2016 [ 0.850000] Lantiq PCIe Root Complex driver, version 2.0.0, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.900000] bio: create slab <bio-0> at 0 [ 0.900000] PCI host bridge to bus 0000:00 [ 0.910000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff] [ 0.910000] pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff] [ 0.920000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.930000] ifx_pcie_rc_class_early_fixup port 0: fixed pcie host bridge to pci-pci bridge [ 0.940000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff] [ 0.940000] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref] [ 0.950000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit] [ 0.950000] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref] [ 0.960000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.960000] pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff] [ 0.970000] pci 0000:00:00.0: bridge window [mem 0x1c100000-0x1c1fffff pref] [ 0.970000] NET: Registered protocol family 8 [ 0.980000] NET: Registered protocol family 20 [ 0.980000] Switching to clocksource MIPS [ 1.030000] NET: Registered protocol family 2 [ 1.030000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 1.040000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 1.040000] TCP: Hash tables configured (established 1024 bind 1024) [ 1.050000] TCP: reno registered [ 1.050000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 1.060000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 1.070000] NET: Registered protocol family 1 [ 1.070000] Lantiq CGU driver, version 1.1.32, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.080000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17, (c) 2009 Infineon Technologies AG [ 1.080000] skb_shared_size:184 [ 1.100000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.100000] fuse init (API version 7.22) [ 1.110000] msgmni has been set to 210 [ 1.110000] io scheduler noop registered (default) [ 1.460000] ttyS0 at MMIO 0x1e100c00 (irq = 107) is a PORT_IFX_ASC [ 1.460000] ifx_usif_uart_init: uart_register_driver failed [ 1.470000] avm_net_trace: Up and running. [ 1.470000] [loadcontrol] set auto - scale=1 [ 1.480000] ifx_pmu_init: Major 245 [ 1.480000] Lantiq PMU driver, version 1.2.6, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.490000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.500000] Infineon Technologies RCU driver version 1.0.7 [ 1.520000] loop: module loaded [ 1.520000] nbd: registered device at major 43 [ 1.550000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64 [ 1.560000] Scanning device for bad blocks [ 1.580000] Bad eraseblock 543 at 0x0000043e0000 [ 1.600000] badblock statistics: [ 1.600000] -------------------- [ 1.600000] start block = 0 [ 1.600000] num blocks = 1024 [ 1.600000] bad blocks = 1 [ 1.610000] [ 1.610000] >> The following table summarize all badblocks to visualize the distribution [ 1.610000] block [ start | count | size/kB ] (start block, number of blocks) [ 1.610000] --------------------------------- [ 1.640000] block [ 543 | 1 | 128 ] [ 1.640000] [ ======================= ] [ 1.640000] [ >> 1 | 128 ] [ 1.650000] Creating 6 MTD partitions on "ifx_nand": [ 1.660000] 0x000000000000-0x000000400000 : "kernel" [ 1.660000] 0x000000400000-0x000003400000 : "filesystem" [ 1.670000] 0x000003400000-0x000003800000 : "reserved-kernel" [ 1.680000] 0x000003800000-0x000006800000 : "reserved-filesystem" [ 1.690000] 0x000006800000-0x000006a00000 : "config" [ 1.690000] 0x000006a00000-0x000008000000 : "nand-filesystem" [ 1.700000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_nand [ 1.710000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_sflash [ 1.720000] Creating 3 MTD partitions on "ifx_sflash": [ 1.720000] 0x000000000000-0x000000020000 : "urlader" [ 1.730000] 0x000000020000-0x000000030000 : "tffs (1)" [ 1.740000] 0x000000030000-0x000000040000 : "tffs (2)" [ 1.740000] Lantiq SPI flash driver, version 2.0.1, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.750000] tun: Universal TUN/TAP device driver, 1.6 [ 1.750000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.760000] SWAPI: Registered character device [switch_api] with major no [81] [ 1.770000] i2c /dev entries driver [ 1.770000] cpuidle: using governor ladder [ 1.780000] cpuidle: using governor menu [ 1.780000] AVM PA 4.3.14 2015-10-21 [ 1.780000] AVM PA skb pktinfo at offset 136 size 196 [ 1.790000] [loadcontrol]module avm_pa registered [ 1.790000] ipip: IPv4 over IPv4 tunneling driver [ 1.800000] TCP: cubic registered [ 1.800000] NET: Registered protocol family 10 [ 1.810000] sit: IPv6 over IPv4 tunneling driver [ 1.810000] NET: Registered protocol family 17 [ 1.820000] l2tp_core: L2TP core driver, V2.0 [ 1.820000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 1.830000] l2tp_netlink: L2TP netlink interface [ 1.830000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 1.840000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 1.840000] 8021q: 802.1Q VLAN Support v1.8 [ 1.850000] Key type dns_resolver registered [ 1.850000] <ifx_fix_timing> [ 1.860000] [TFFS3_Init] No storage module registered, trying legacy fallback [ 1.860000] [TFFS3_Register_LGCY] Called [ 1.870000] [TFFS3_LGCY_Configure] Called [ 1.870000] [TFFS3_LGCY_Setup] using mtd7(tffs (1)), mtd8(tffs (2)) [ 1.880000] [TFFS3_LGCY_Setup] mtd "tffs (1)": segment value 1 [ 1.880000] [TFFS3_LGCY_Setup] mtd "tffs (2)": segment value 1 [ 1.890000] [TFFS3_LGCY_Setup] Using segment 1 (avail: 1 + 1) [ 1.890000] [TFFS3_LGCY_Setup] mtd8 size=0x10000 [ 1.900000] TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 3.0) [ 1.900000] [rescan_segment] Called with mode=2 [ 1.900000] TFFS: Clearing index for update [ 1.920000] Adam2 environment variables API installed. [ 1.920000] [simple-profiling]: 2 performance counters implemented, NEW_34K [ 1.930000] Enable Performance Counter 0 for Data cache load/stores (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 1.940000] Setup tcs=0x2 current_tc_mask=0x2, reg=0 [ 1.950000] [simple-profiling]: 2 performance counters implemented, NEW_34K [ 1.950000] Enable Performance Counter 1 for Data cache load/store misses (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 1.970000] Setup tcs=0x2 current_tc_mask=0x2, reg=1 [ 1.970000] {avmnet_cfg_netinit} [ 1.980000] [avmnet] No config found for HWRev 175, HWSubRev 5, Profile-ID 0, trying base config for HWSubRev [ 1.990000] [avmnet] No config found for HWRev 175, HWSubRev 5, trying base config for HWRev [ 1.990000] [avmnet] [avmnet_swi_7port_init] Init on module swi_vr9 called. [ 2.450000] [ppe_eth_init] init_hw() [ 2.460000] [init_hw] ppe_hw_init=0xff successful [ 2.460000] [ppe_eth_init] ifx_proc_file_create() [ 2.470000] [ppe_eth_init] dma_setup_init() [ 2.470000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown unicast frames 0x68 [ 2.480000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown multicast frames 0x68 [ 5.720000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth0): 24:65:11:6e:53:8e [ 5.730000] avmnet: avm_pa: register pid eth0 [ 5.740000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth1): 24:65:11:6e:53:8f [ 5.750000] avmnet: avm_pa: register pid eth1 [ 5.750000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth2): 24:65:11:6e:53:92 [ 5.760000] avmnet: avm_pa: register pid eth2 [ 5.760000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth3): 24:65:11:6e:53:93 [ 5.770000] avmnet: avm_pa: register pid eth3 [ 5.820000] SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock1 [ 5.830000] yaffs: dev is 32505857 name is "mtdblock1" ro [ 5.830000] yaffs: passed flags "" [ 5.850000] VFS: Mounted root (yaffs filesystem) readonly on device 31:1. [ 5.860000] devtmpfs: mounted [ 5.860000] Freeing unused kernel memory: 300K (80835000 - 80880000) [ 6.960000] TFFS Name Table L [ 7.000000] [MTD4]: name = "config" [ 7.000000] [MTD4]: erase: mtd size 0x200000 block size 0x20000 erase block count 0x10 [ 7.010000] [MTD4]: erase all blocks. [ 7.010000] [MTD4]: erase block 0(0x0) from 16(0x10) [ 7.020000] [MTD4]: erase block 1(0x1) from 16(0x10) [ 7.030000] [MTD4]: erase block 2(0x2) from 16(0x10) [ 7.030000] [MTD4]: erase block 3(0x3) from 16(0x10) [ 7.040000] [MTD4]: erase block 4(0x4) from 16(0x10) [ 7.040000] [MTD4]: erase block 5(0x5) from 16(0x10) [ 7.050000] [MTD4]: erase block 6(0x6) from 16(0x10) [ 7.050000] [MTD4]: erase block 7(0x7) from 16(0x10) [ 7.060000] [MTD4]: erase block 8(0x8) from 16(0x10) [ 7.060000] [MTD4]: erase block 9(0x9) from 16(0x10) [ 7.070000] [MTD4]: erase block 10(0xa) from 16(0x10) [ 7.070000] [MTD4]: erase block 11(0xb) from 16(0x10) [ 7.080000] [MTD4]: erase block 12(0xc) from 16(0x10) [ 7.090000] [MTD4]: erase block 13(0xd) from 16(0x10) [ 7.090000] [MTD4]: erase block 14(0xe) from 16(0x10) [ 7.100000] [MTD4]: erase block 15(0xf) from 16(0x10) [ 7.160000] yaffs: dev is 32505860 name is "mtdblock4" rw [ 7.170000] yaffs: passed flags "" [ 7.430000] ------------[ cut here ]------------ [ 7.430000] WARNING: at mm/page_alloc.c:1520 get_page_from_freelist+0x610/0x620() [ 7.440000] Call Trace: [ 7.440000] ---[ end trace f21a5ec257bdf6db ]--- [ 9.380000] [avm_urlader_env_set_variable] opening ID 0x1ae for writing [ 9.480000] led_modul_Fritz_Box_3370: module license ' [ 9.480000] (C) Copyright 2012 by AVM [ 9.480000] ' taints kernel. [ 9.490000] Disabling lock debugging due to kernel taint [ 9.500000] [module-alloc-by-name] give 0x1a000 bytes at 0x81104000 to module 'led_modul_Fritz_Box_3370' (0xc76000 bytes left) [ 9.520000] [LED] use GPIO 32 for 'gpio_avm_led_power' [ 9.520000] [LED] use GPIO 38 for 'gpio_avm_led_lan_all' [ 9.530000] [LED] use GPIO 35 for 'gpio_avm_led_wlan' [ 9.530000] [LED] use GPIO 36 for 'gpio_avm_led_pppoe' [ 9.540000] [LED] use GPIO 47 for 'gpio_avm_led_info' [ 9.540000] [LED] use GPIO 34 for 'gpio_avm_led_info_red' [ 9.550000] [BUTTON] use GPIO 29 for 'gpio_avm_button_wlan' [ 9.550000] [BUTTON] use GPIO 1 for 'gpio_avm_button_power' [ 9.570000] AVM_WATCHDOG: System Init UEberwachung 120 Sekunden [ 10.680000] [module-alloc-by-name] give 0x3000 bytes at 0x8111e000 to module 'rtc_avm' (0xc73000 bytes left) [ 10.690000] rtc-avm rtc-avm.0: rtc core: registered avm as rtc0 [ 10.690000] [avm-rtc]: avm_rtc_probe: register: ret=0x876fa400 [ 10.700000] [avm-rtc]: avm_rtc_probe: success [ 10.900000] [ 10.900000] [avm_debug] redirecting kernel-messages (/dev/debug) ROM VER: 1.0.5 CFG 05 Initial DDR setting for SDRAM test pass Initial DDR check ok... [/] (AVM) EVA Revision: 1.1186 Version: 2186 (C) Copyright 2005 AVM Date: Apr 13 2011 Time: 14:46:06 (2) 2 0x0-0x741D [FLASH:] MACRONIX Uniform-Flash 256kB 256 Bytes WriteBuffer [FLASH:](Eraseregion [0] 4 sectors a 64kB) [NAND:] 128MB HYNIX 2048 Pagesize 128k Blocksize 1024 Blocks 8Bit 1 CS [SYSTEM:] VR9 on 500MHz/250MHz/250MHz .Infineon PHY11G detected Eva_AVM >.....................................................[] set PHYs in Reset 0x1 Lantiq xDSL CPE VR9 phym = 08000000, mem = 08000000, max_pfn = 00008000 Reserving memory for CP1 @0xa8000000, size 0x00000000 plat_device_tree_setup: AVM hardware subrevision 5 plat_device_tree_setup: using Fallback device-tree of AVM hardware subrevision 2 DT: d0 0d fe ed 00 00 09 61 [ 0.000000] Linux version 3.10.73 (jwetter@EmbeddedVM) (gcc version 4.8.3 (Buildroot 2014.08) ) #1 SMP Wed Aug 17 11:54:03 CEST 2016 [ 0.000000] [env_init] 0x8101a760[0] [ 0.000000] [env_init] 0x8101a7a0[1] [ 0.000000] [env_init] 0x8101a7e0[2] [ 0.000000] [env_init] switch to ram location [ 0.000000] [init_avm_kernel_config] AVM Kernel Config (ptr 80825000) [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: module memory entry [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: version info entry [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 0 found [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 1 found [ 0.000000] [init_avm_kernel_config] AVM Kernel Config: device-tree for subrev 2 found [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019555 (MIPS 34Kc) [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 08000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] [module-alloc] use 0xc90000 bytes at 0x81104000 [ 0.000000] PERCPU: Embedded 7 pages/cpu @81d98000 s7072 r8192 d13408 u32768 [ 0.000000] Kernel command line: console=ttyS0,115200n8r nor_size=0MB sflash_size=256KB nand_size=128MB ethaddr=24:65:11:6E:53:8E [ 0.000000] [NAND] nand_size = 0x8000000 [ 0.000000] PID hash table entries: 512 (order: -1, 2048 bytes) [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Writing ErrCtl register=0007e2b0 [ 0.000000] Readback ErrCtl register=0007e2b0 [ 0.000000] Memory: 107752k/131072k available (5705k kernel code, 23320k reserved, 2690k data, 300k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:181 [ 0.000000] SRSConf0 0x3feffbfe: SRS1: 0xffffffff, SRS2 0xffffffff, SRS3 0xffffffff [ 0.000000] Lantiq ICU driver, version 3.0.1, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.000000] Console: colour dummy device 80x25 [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.000000] console [ttyS0] enabled, bootconsole disabled [ 0.020000] Calibrating delay loop... 331.77 BogoMIPS (lpj=1658880) [ 0.080000] pid_max: default: 32768 minimum: 301 [ 0.080000] Security Framework initialized [ 0.080000] Mount-cache hash table entries: 512 [ 0.090000] CPU1 revision is: 00019555 (MIPS 34Kc) [ 0.170000] Brought up 2 CPUs [ 0.170000] [yield_context_init] cpu=1 tc=2 mask=300 [ 0.180000] [yield_context_init] cpu=0 tc=3 mask=410 [ 0.180000] devtmpfs: initialized [ 0.200000] pinctrl core: initialized pinctrl subsystem [ 0.200000] Creating Config Table [ 0.200000] [avm_generate_hw_config_table_from_device_tree] gpio_cnt: 21 [ 0.210000] NET: Registered protocol family 16 [ 0.220000] Reboot Status is: Soft-Reboot [ 0.220000] [TFFS3_Early_Init] called [ 0.230000] [avmnet] [avmnet_cfg_init] Driver version: 6.221.2.4 - Revision 1496:3477 - Mi 17. Aug 11:53:18 CEST 2016 [ 0.850000] Lantiq PCIe Root Complex driver, version 2.0.0, (c) 2001-2011 Lantiq Deutschland GmbH [ 0.900000] bio: create slab <bio-0> at 0 [ 0.900000] PCI host bridge to bus 0000:00 [ 0.910000] pci_bus 0000:00: root bus resource [mem 0x1c000000-0x1cffffff] [ 0.910000] pci_bus 0000:00: root bus resource [io 0x1d800000-0x1d8fffff] [ 0.920000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.930000] ifx_pcie_rc_class_early_fixup port 0: fixed pcie host bridge to pci-pci bridge [ 0.940000] pci 0000:00:00.0: BAR 8: assigned [mem 0x1c000000-0x1c0fffff] [ 0.940000] pci 0000:00:00.0: BAR 9: assigned [mem 0x1c100000-0x1c1fffff pref] [ 0.950000] pci 0000:01:00.0: BAR 0: assigned [mem 0x1c000000-0x1c01ffff 64bit] [ 0.950000] pci 0000:01:00.0: BAR 6: assigned [mem 0x1c100000-0x1c10ffff pref] [ 0.960000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.960000] pci 0000:00:00.0: bridge window [mem 0x1c000000-0x1c0fffff] [ 0.970000] pci 0000:00:00.0: bridge window [mem 0x1c100000-0x1c1fffff pref] [ 0.970000] NET: Registered protocol family 8 [ 0.980000] NET: Registered protocol family 20 [ 0.980000] Switching to clocksource MIPS [ 1.030000] NET: Registered protocol family 2 [ 1.030000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 1.040000] TCP bind hash table entries: 1024 (order: 1, 8192 bytes) [ 1.050000] TCP: Hash tables configured (established 1024 bind 1024) [ 1.050000] TCP: reno registered [ 1.050000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 1.060000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 1.070000] NET: Registered protocol family 1 [ 1.070000] Lantiq CGU driver, version 1.1.32, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.090000] IFX DMA driver, version ifxmips_dma_core.c:v1.0.17, (c) 2009 Infineon Technologies AG [ 1.090000] skb_shared_size:184 [ 1.110000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.110000] fuse init (API version 7.22) [ 1.120000] msgmni has been set to 210 [ 1.120000] io scheduler noop registered (default) [ 1.470000] ttyS0 at MMIO 0x1e100c00 (irq = 107) is a PORT_IFX_ASC [ 1.480000] ifx_usif_uart_init: uart_register_driver failed [ 1.480000] avm_net_trace: Up and running. [ 1.490000] [loadcontrol] set auto - scale=1 [ 1.490000] ifx_pmu_init: Major 245 [ 1.500000] Lantiq PMU driver, version 1.2.6, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.500000] Lantiq GPIO driver, version 1.3.2, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.510000] Infineon Technologies RCU driver version 1.0.7 [ 1.530000] loop: module loaded [ 1.540000] nbd: registered device at major 43 [ 1.560000] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64 [ 1.580000] Scanning device for bad blocks [ 1.600000] Bad eraseblock 543 at 0x0000043e0000 [ 1.620000] badblock statistics: [ 1.620000] -------------------- [ 1.620000] start block = 0 [ 1.620000] num blocks = 1024 [ 1.620000] bad blocks = 1 [ 1.630000] [ 1.630000] >> The following table summarize all badblocks to visualize the distribution [ 1.630000] block [ start | count | size/kB ] (start block, number of blocks) [ 1.630000] --------------------------------- [ 1.650000] block [ 543 | 1 | 128 ] [ 1.660000] [ ======================= ] [ 1.660000] [ >> 1 | 128 ] [ 1.670000] Creating 6 MTD partitions on "ifx_nand": [ 1.670000] 0x000000000000-0x000000400000 : "kernel" [ 1.680000] 0x000000400000-0x000003400000 : "filesystem" [ 1.690000] 0x000003400000-0x000003800000 : "reserved-kernel" [ 1.700000] 0x000003800000-0x000006800000 : "reserved-filesystem" [ 1.700000] 0x000006800000-0x000006a00000 : "config" [ 1.710000] 0x000006a00000-0x000008000000 : "nand-filesystem" [ 1.720000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_nand [ 1.720000] [TFFS3_Register_Panic_CB] registering panic callback for mtd ifx_sflash [ 1.730000] Creating 3 MTD partitions on "ifx_sflash": [ 1.740000] 0x000000000000-0x000000020000 : "urlader" [ 1.740000] 0x000000020000-0x000000030000 : "tffs (1)" [ 1.750000] 0x000000030000-0x000000040000 : "tffs (2)" [ 1.760000] Lantiq SPI flash driver, version 2.0.1, (c) 2001-2011 Lantiq Deutschland GmbH [ 1.770000] tun: Universal TUN/TAP device driver, 1.6 [ 1.770000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 1.780000] SWAPI: Registered character device [switch_api] with major no [81] [ 1.780000] i2c /dev entries driver [ 1.790000] cpuidle: using governor ladder [ 1.790000] cpuidle: using governor menu [ 1.800000] AVM PA 4.3.14 2015-10-21 [ 1.800000] AVM PA skb pktinfo at offset 136 size 196 [ 1.800000] [loadcontrol]module avm_pa registered [ 1.810000] ipip: IPv4 over IPv4 tunneling driver [ 1.810000] TCP: cubic registered [ 1.820000] NET: Registered protocol family 10 [ 1.820000] sit: IPv6 over IPv4 tunneling driver [ 1.830000] NET: Registered protocol family 17 [ 1.830000] l2tp_core: L2TP core driver, V2.0 [ 1.840000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 1.840000] l2tp_netlink: L2TP netlink interface [ 1.850000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 1.850000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 1.860000] 8021q: 802.1Q VLAN Support v1.8 [ 1.860000] Key type dns_resolver registered [ 1.870000] <ifx_fix_timing> [ 1.870000] [TFFS3_Init] No storage module registered, trying legacy fallback [ 1.880000] [TFFS3_Register_LGCY] Called [ 1.880000] [TFFS3_LGCY_Configure] Called [ 1.890000] [TFFS3_LGCY_Setup] using mtd7(tffs (1)), mtd8(tffs (2)) [ 1.890000] [TFFS3_LGCY_Setup] mtd "tffs (1)": segment value 1 [ 1.900000] [TFFS3_LGCY_Setup] mtd "tffs (2)": segment value 1 [ 1.900000] [TFFS3_LGCY_Setup] Using segment 1 (avail: 1 + 1) [ 1.910000] [TFFS3_LGCY_Setup] mtd8 size=0x10000 [ 1.910000] TFFS: tiny flash file system driver. GPL (c) AVM Berlin (Version 3.0) [ 1.920000] [rescan_segment] Called with mode=2 [ 1.920000] TFFS: Clearing index for update [ 1.930000] Adam2 environment variables API installed. [ 1.940000] [simple-profiling]: 2 performance counters implemented, NEW_34K [ 1.940000] Enable Performance Counter 0 for Data cache load/stores (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 1.960000] Setup tcs=0x2 current_tc_mask=0x2, reg=0 [ 1.960000] [simple-profiling]: 2 performance counters implemented, NEW_34K [ 1.970000] Enable Performance Counter 1 for Data cache load/store misses (User-Mode enabled Supervisor-Mode enabled Kernel-Mode enabled Exeption-Mode disable) [ 1.980000] Setup tcs=0x2 current_tc_mask=0x2, reg=1 [ 1.990000] {avmnet_cfg_netinit} [ 1.990000] [avmnet] No config found for HWRev 175, HWSubRev 5, Profile-ID 0, trying base config for HWSubRev [ 2.000000] [avmnet] No config found for HWRev 175, HWSubRev 5, trying base config for HWRev [ 2.010000] [avmnet] [avmnet_swi_7port_init] Init on module swi_vr9 called. [ 2.470000] [ppe_eth_init] init_hw() [ 2.470000] [init_hw] ppe_hw_init=0xff successful [ 2.480000] [ppe_eth_init] ifx_proc_file_create() [ 2.480000] [ppe_eth_init] dma_setup_init() [ 2.490000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown unicast frames 0x68 [ 2.500000] [avmnet] [avmnet_swi_7port_disable_learning] Configuring CPU-port to receive all unknown multicast frames 0x68 [ 5.650000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth0): 24:65:11:6e:53:8e [ 5.660000] a avm_pa: register pid eth0 [ 5.660000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth1): 24:65:11:6e:53:8f [ 5.670000] avmnet: avm_pa: register pid eth1 [ 5.670000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth2): 24:65:11:6e:53:92 [ 5.680000] avmnet: avm_pa: register pid eth2 [ 5.690000] [avmnet_set_macaddr] Setup Mac Addr for Device(eth3): 24:65:11:6e:53:93 [ 5.690000] avmnet: avm_pa: register pid eth3 [ 5.740000] SQUASHFS error: Can't find a SQUASHFS superblock on mtdblock1 [ 5.750000] yaffs: dev is 32505857 name is "mtdblock1" ro [ 5.760000] yaffs: passed flags "" [ 5.780000] VFS: Mounted root (yaffs filesystem) readonly on device 31:1. [ 5.780000] devtmpfs: mounted [ 5.790000] Freeing unused kernel memory: 300K (80835000 - 80880000) [ 6.880000] TFFS Name Table L [ 6.980000] yaffs: dev is 32505860 name is "mtdblock4" rw [ 6.990000] yaffs: passed flags "" [ 8.630000] [avm_urlader_env_set_variable] opening ID 0x1ae for writing [ 8.730000] led_modul_Fritz_Box_3370: module license ' [ 8.730000] (C) Copyright 2012 by AVM [ 8.730000] ' taints kernel. [ 8.740000] Disabling lock debugging due to kernel taint [ 8.750000] [module-alloc-by-name] give 0x1a000 bytes at 0x81104000 to module 'led_modul_Fritz_Box_3370' (0xc76000 bytes left) [ 8.770000] [LED] use GPIO 32 for 'gpio_avm_led_power' [ 8.770000] [LED] use GPIO 38 for 'gpio_avm_led_lan_all' [ 8.780000] [LED] use GPIO 35 for 'gpio_avm_led_wlan' [ 8.780000] [LED] use GPIO 36 for 'gpio_avm_led_pppoe' [ 8.790000] [LED] use GPIO 47 for 'gpio_avm_led_info' [ 8.790000] [LED] use GPIO 34 for 'gpio_avm_led_info_red' [ 8.800000] [BUTTON] use GPIO 29 for 'gpio_avm_button_wlan' [ 8.800000] [BUTTON] use GPIO 1 for 'gpio_avm_button_power' [ 8.820000] AVM_WATCHDOG: System Init UEberwachung 120 Sekunden [ 9.300000] [module-alloc-by-name] give 0x3000 bytes at 0x8111e000 to module 'rtc_avm' (0xc73000 bytes left) [ 9.310000] rtc-avm rtc-avm.0: rtc core: registered avm as rtc0 [ 9.320000] [avm-rtc]: avm_rtc_probe: register: ret=0x87750400 [ 9.320000] [avm-rtc]: avm_rtc_probe: success [ 9.530000] [ 9.530000] [avm_debug] redirecting kernel-messages (/dev/debug)


Other Resources

Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
toh/avm/fritz.box.wlan.3370.txt · Last modified: 2020/10/19 01:41 by vasilis74