AUKEY WF-R8

The AUKEY WF-R8 is an AC1200 WiFi range extender based on the MediaTek MT7628AN with two Fast Ethernet ports, a 802.11n 2T/2R 2.4 GHz 300Mbps and a 802.11ac 2T/2R 5 GHz 867 Mbps wireless interfaces.

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
WF-R8MediaTek MT7628ANMediaTek MT7628AN864MediaTek MT7628AN, MediaTek MT7612Eb/g/na/n/ac2---

The WF-R8 ships with a Linux 2.6 kernel. It features a web interface through lighttpd and a telnet open on port 2323 or 23.

The web interface is very simple, although it does not offer much options.

Configuration files can also be modified using telnet, but the modifications will be erased upon reboot. Permanent changes must be done by modifying values stored in NVRAM, using the tool ralink_init.

The stock firmware web interface does not seem to accept the OpenWrt images.

OpenWrt images can be flashed from within the U-boot bootloader via TFTP.

Some devices may have a restricted boot loader that pretends to try TFTP recovery but does not request anything.

In these cases, you may want to flash a working boot loader for that device. A good summary on this topic can be found here. The unlocked bootloader can be found here.

  1. Set your computer to 192.168.10.100
  2. Set up a TFTP server on your computer
  3. Rename the OpenWrt xxxx-sysupgrade.bin image as firmware.bin and place it in the root folder of the TFTP server
  4. Power off the device and connect an Ethernet cable from its LAN port to your computer
  5. Press the WPS button (and keep it pressed)
  6. Power on the device
  7. After a few seconds, when the LAN LED stops blinking very fast, release the WPS button
  8. After one minute or so, OpenWrt will be running and accessible as with any other device, normally at 192.168.1.1. If nothing happens, retry with the WAN/LAN port.
Architecture MIPS 24KEc V5.5 (ramips)
Vendor MediaTek
Bootloader U-boot 1.1.3
System-On-Chip MediaTek MT7628AN
CPU Speed 580MHz
RAM memory 64 MB DDR2
Flash memory 8 MB (8192 KiB)
Flash chip GD25Q64B (64M-bit Serial Flash)
Wired network 2 x Ethernet 100 Mbps (switched)
Ethernet chip MediaTek mtk_soc_eth (SoC)
Ethernet switch MediaTek rt305x (SoC)
Wireless network 1 2.4 GHz 802.11n MiMo 2×2:2
Wireless chip 1 MediaTek mt76_wmac (SoC)
Wireless network 2 5 GHz 802.11ac MiMo 2×2:2
Wireless chip 2 MediaTek MT7612EN
Wireless antennas 4 x external
USB No
Serial port Internal

FIXME Please add photos showing the PCB serial pins.

The device does not have exposed serial port pins. There are very tiny TX/RX pins labeled T/R by the bios chip and requires fine soldering

57600, 8, no parity, 1 stop, no hardware

FIXME Investigate if/how the other four LEDs work.

The WF-R8 has seven leds. Three of them show the signal strength of the repeated wlan and come preconfigured in the system. However, they don't light up in the default installation. In order to make them work, the package rssileds must be installed.

Details on how to configure the LEDs can be found here: LED configuration /etc/config/system.

OEM bootlog

U-Boot 1.1.3 (Jun 30 2016 - 13:32:32) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fb8000 flash manufacture id: c8, device id 40 17 find flash: GD25Q64B *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.3.0.0 -------------------------------------------- ASIC 7628_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Jun 30 2016 Time:13:32:32 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 575 MHZ #### estimate memory size =64 Mbytes RESET MT7628 PHY!!!!!! Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. You choosed 3 0 3: System Boot system code via Flash. ## Booting image at bc050000 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 4761963 Bytes = 4.5 MB Load Address: 80000000 Entry Point: 8000c150 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000c150) ... ## Giving linux memsize in MB, 64 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.36 (root@ubuntusvr1) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #899 Mon Nov 7 17:37:34 CST 2016 The CPU feqenuce set to 575 MHz MIPS CPU sleep mode enabled. CPU revision is: 00019655 (MIPS 24Kc) Software DMA cache coherency Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00004000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00004000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0 PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Writing ErrCtl register=0007bab8 Readback ErrCtl register=0007bab8 Memory: 56812k/65536k available (3696k kernel code, 8724k reserved, 1022k data, 3140k init, 0k highmem) NR_IRQS:128 console [ttyS1] enabled Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 NET: Registered protocol family 16 RALINK_GPIOMODE = 54054404 RALINK_GPIOMODE = 54044404 ***** Xtal 40MHz ***** start PCIe register access RALINK_RSTCTRL = 2400000 RALINK_CLKCFG1 = fdbfffc0 *************** MT7628 PCIe RC mode ************* PCIE0 enabled Port 0 N_FTS = 1b105000 init_rt2880pci done bio: create slab <bio-0> at 0 vgaarb: loaded SCSI subsystem initialized pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit] pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit] (PCI address [0x20000000-0x200fffff] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref] pci 0000:00:00.0: PCI bridge to [bus 01-01] pci 0000:00:00.0: bridge window [io disabled] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref] BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 20200000 res[1]->end = 2020ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0 res[0]->start = 20000000 res[0]->end = 200fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource Ralink Systick timer NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 Load Ralink Timer0 Module Load Ralink Timer1 Module Load Ralink Timer2 Module fuse init (API version 7.15) msgmni has been set to 110 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) gpiomode one 0000 = 0x55144410 gpiomode 11111 = 0x0 gpiomode 22222 = 0x55 Ralink gpio driver initialized = 73 Ralink gpio driver initialized Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A brd: module loaded flash manufacture id: c8, device id 40 17 Wavlink Encryption System... Wavlink Encryption System is installing GD25Q64B(c8 40170000) (8192 Kbytes) mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 5 MTD partitions on "raspi": 0x000000000000-0x000000800000 : "ALL" 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config" 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000001000000 : "Kernel" mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000 rdm_major = 253 GMAC1_MAC_ADRH -- : 0x0000803f GMAC1_MAC_ADRL -- : 0x5db6eae1 Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500! GMAC1_MAC_ADRH -- : 0x0000803f GMAC1_MAC_ADRL -- : 0x5db6eae1 PROC INIT OK! my_net_link_3: create netlink socket ok. PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 === pAd = c0147000, size = 1352880 === <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x <-- RTMPAllocAdapterBlock, Status=0 RtmpChipOpsHook(492): Not support for HIF_MT yet! mt7628_init()--> mt7628_init(FW(8a00), HW(8a01), CHIPID(7628)) e2.bin mt7628_init(1133)::(2), pChipCap->fw_len(63888) mt_bcn_buf_init(218): Not support for HIF_MT yet! <--mt7628_init() GACT probability on Mirror/redirect action on Simple TC action Loaded netem: version 1.2 u32 classifier Performance counters on input device check on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (887 buckets, 3548 max) ctnetlink v0.93: registering with nfnetlink. nf_conntrack_rtsp v0.6.21 loading NF_TPROXY: Transparent proxy support initialized, version 4.1.0 NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. matchsize=264 xt_time: kernel timezone is -0000 IPVS: Registered protocols () IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: ipvs loaded. GRE over IPv4 demultiplexor driver gre: can't add protocol nf_nat_rtsp v0.6.21 loading ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully arp_tables: (C) 2002 David S. Miller TCP cubic registered NET: Registered protocol family 17 L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> Warning: unable to open an initial console. Freeing unused kernel memory: 3140k freed Algorithmics/MIPS FPU Emulator v1.5 Welcome to __ ___ _____ _____ _ _______ ______ _____ _ ___ | \ / || ___|| __ \ | || __ ||__ __|| ___|| | / / | ^ || |__ | | \ \| || | | | | | | |__ | |/ / | | | || ___|| | | || || |__| | | | | ___|| \ | | | || |___ | |__/ /| || __ | | | | |___ | |\ \ |__| |___||_____||_____/ |_||_| |_| |_| |_____||_| \__\ = Everyday Genius = The timer is still in use... Wavlink Encryption System is unlocked. initGpio 38 Password for 'admin' changed ##### disable 1st wireless interface ##### ##### disable 2nd wireless interface ##### rmmod: rlt_wifi: No such file or directory RootMacAddress:80:3F:5D:B6:EA:E3 RootMacAddress:80:3F:5D:B6:EA:E3 register rt2860 === pAd = c0782000, size = 2190712 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc0680000, csr_addr=0xc0680000! device_id =0x7662 ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a E2pAccessMode=0 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Not Equal! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) IF(ra0) The length of WAPI PSKPassPhrase is invalid(len=0). RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=2 NVM is efuse and the information is too less to bring up the interface Force to use Flash mode NVM is FLASH mode (pAd->flash_offset = 0x48000) get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai TX_BCN DESC a2992000 size = 320 RX[0] DESC a2994000 size = 2048 RX[1] DESC a2995000 size = 1024 E2pAccessMode=0 cfg_mode=9 cfg_mode=9 wmode_band_equal(): Band Equal! AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) load fw image from fw_header_image AndesMTLoadFwMethod1(2174)::pChipCap->fw_len(63888) FW Version:20151201 FW Build Date:20151201183641 CmdAddressLenReq:(ret = 0) CmdFwStartReq: override = 1, address = 1048576 CmdStartDLRsp: WiFI FW Download Success MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC) efuse_probe: efuse = 10000002 RtmpChipOpsEepromHook::e2p_type=2, inf_Type=4 RtmpEepromGetDefault::e2p_dafault=2 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2 NVM is FLASH mode 1. Phy Mode = 14 Country Region from e2p = ffff tssi_1_target_pwr_g_band = 36 2. Phy Mode = 14 3. Phy Mode = 14 NICInitPwrPinCfg(11): Not support for HIF_MT yet! NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet! mt_mac_init()--> MtAsicInitMac()--> mt7628_init_mac_cr()--> MtAsicSetMacMaxLen(1241): Set the Max RxPktLen=1024! <--mt_mac_init() WTBL Segment 1 info: MemBaseAddr/FID:0x28000/0 EntrySize/Cnt:32/128 WTBL Segment 2 info: MemBaseAddr/FID:0x40000/0 EntrySize/Cnt:64/128 WTBL Segment 3 info: MemBaseAddr/FID:0x42000/64 EntrySize/Cnt:64/128 WTBL Segment 4 info: MemBaseAddr/FID:0x44000/128 EntrySize/Cnt:32/128 AntCfgInit(2892): Not support for HIF_MT yet! MCS Set = ff ff 00 00 01 MtAsicSetChBusyStat(826): Not support for HIF_MT yet! [PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0 [PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 MtAsicSetRalinkBurstMode(2919): Not support for HIF_MT yet! MtAsicSetPiggyBack(763): Not support for HIF_MT yet! reload DPD from flash , 0x9F = [c600] doReload bit7[0] CmdLoadDPDDataFromFlash: Channel = 11, DoReload = 0 MtAsicSetTxPreamble(2898): Not support for HIF_MT yet! CmdSlotTimeSet:(ret = 0) MtAsicAddSharedKeyEntry(1308): Not support for HIF_MT yet! The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2 MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0 Main bssid = 80:3f:5d:b6:ea:e3 <==== rt28xx_init, Status=0 The 7628 UUID MacAddress = 80:3f:5d:b6:ea:e3 The 7628 UUID MacAddress = 80:3f:5d:b6:ea:e3 mt7628_set_ed_cca: TURN OFF EDCCA mac 0x10618 = 0xd7083f0f, EDCCA_Status=0 WiFi Startup Cost (ra0): 0.916s build time = 20141115060606a rom patch for E3 IC platform = ALPS hw/sw version = ▒▒ patch version = FW Version:0.0.00 Build:1 Build Time:201511101431____ fw for E3 IC RX[0] DESC a2b59000 size = 4096 RX[1] DESC a2b5a000 size = 4096 E2pAccessMode=0 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Not Equal! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 default ApCliAPSDCapable[0]=0 Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) IF(ra0) The length of WAPI PSKPassPhrase is invalid(len=0). 1. Phy Mode = 49 get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (171) drivers/net/wireless/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:2890 assert (ad->TxPower[choffset].Channel == 42)failed Country Region from e2p = ffff mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0 mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=1, ePA_type=0 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=15, low_temp_slope=9 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=13, low_temp_slope=16 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=-7, tc_upper_bound=4 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=-7, tc_upper_bound=5 mt76x2_get_external_lna_gain::LNA type=0x0, BLNAGain=0xffffff8c, ALNAGain0=0xffffff8c, ALNAGain1=0xffffff8c, ALNAGain2=0xffffff8c 2. Phy Mode = 49 3. Phy Mode = 49 andes_pci_fw_init 0x1300 = 00073200 AntCfgInit: primary/secondary ant 0/1 andes_load_cr:cr_type(2) ChipStructAssign(): MT76x2 hook ! MCS Set = ff ff 00 00 01 mt76x2_bbp_adjust():rf_bw=2, ext_ch=3, PrimCh=40, HT-CentCh=38, VHT-CentCh=42 APStartUp(): AP Set CentralFreq at 42(Prim=40, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) mt76x2_calibration(channel = 42) @@@ ed_monitor_exit : ===> @@@ ed_monitor_exit : <=== Main bssid = 80:3f:5d:b6:ea:e4 mt76x2_reinit_agc_gain:original agc_vga0 = 0x48, agc_vga1 = 0x48 mt76x2_reinit_agc_gain:updated agc_vga0 = 0x48, agc_vga1 = 0x48 mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x33, hi_lna1 = 0x33 mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x33, hi_lna1 = 0x33 original vga value(chain0) = 48 original vga value(chain1) = 48 <==== rt28xx_init, Status=0 get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! ifconfig: ioctl 0x8913 failed: No such device brctl: bridge br0: No such device or address ##### configVIF ##### killall: wandaemRaeth v3.1 (on: no process kTaskletilled ) phy_tx_ring = 0x01d5e000, tx_ring = 0xa1d5e000 phy_rx_ring0 = 0x01d60000, rx_ring0 = 0xa1d60000 GMAC1_MAC_ADRH -- : 0x0000803f GMAC1_MAC_ADRL -- : 0x5db6eae1 RT305x_ESW: Link Status Changed ======>>>>> RT305x_ESW: Link Status Changed ======>>>>> p0 = 0 p1 = 0 p2 = 0 p3 = 0 p4 = 0 hotplug 0 vconfig: ioctl error for rem: No such device vconfig: ioctl error for rem: No such device rmmod: 8021q: No such file or directory device eth2 entered promiscuous mode ##### 1010101010101 config-vlan.sh 2 LLLLW config Ralink ESW vlan partition (LLLLW) ##### switch reg write offset=14, value=405555 switch reg write offset=50, value=2001 switch reg write offset=98, value=7f3f switch reg write offset=e4, value=3f switch reg write offset=40, value=1001 switch reg write offset=44, value=1001 switch reg write offset=48, value=1002 switch reg write offset=70, value=ffff506f done. device ra0 entered promiscuous mode device eth2.1 entered promiscuous mode device rai0 entered promiscuous mode ##### enable 2nd wireless interface ##### br0: port 3(rai0) entering learning state br0: port 3(rai0) entering learning state br0: port 2(eth2.1) entering learning state br0: port 2(eth2.1) entering learning state br0: port 1(ra0) entering learning state br0: port 1(ra0) entering learning state route: ioctl 0x890c failed: No such process route: ioctl 0x890b failed: Network is unreachable ifconfig: ioctl 0x8914 failed: Cannot assign requested address ifconfig: ioctl 0x8914 failed: Cannot assign requested address dhcp status 0 lan.sh route: ioctl 0x890c failed: No such process device eth2.2 entered promiscuous mode br0: port 4(eth2.2) entering learning state br0: port 4(eth2.2) entering learning state ifconfig: ioctl 0x8913 failed: No such device /bin/radvd.sh: line 7: cannot create /proc/sys/net/ipv6/conf/all/forwarding: nonexistent directory rm: cannot remove '/etc/radvd.conf': No such file or directory /sbin/internet.sh: line 1273: long_loop: not found route: ioctl 0x890c failed: No such process sh: miniupnpd.sh: not found killall: rt2860apd: no process killed sh: miniupnpd.sh: not found killall: rtinicapd: no process killed killall: wapid: no process killed iptables v1.4.10: Couldn't load target `macipport_filter':File not found Try `iptables -h' or 'iptables --help' for more information. iptables: No chain/target/match by that name. iptables v1.4.10: Couldn't load target `web_filter':File not found Try `iptables -h' or 'iptables --help' for more information. iptables: No chain/target/match by that name. iptables v1.4.10: Couldn't load target `malicious_filter':File not found Try `iptables -h' or 'iptables --help' for more information. iptables: No chain/target/match by that name. iptables v1.4.10: Couldn't load target `malicious_input_filter':File not found Try `iptables -h' or 'iptables --help' for more information. iptables: No chain/target/match by that name. iptables v1.4.10: Couldn't load target `port_trigger':File not found Try `iptables -h' or 'iptables --help' for more information. iptables: No chain/target/match by that name. iptables v1.4.10: Couldn't load target `trigger_prerouting':File not found Try `iptables -h' or 'iptables --help' for more information. iptables: No chain/target/match by that name. sh: /bin/super_dmz: not found br0: port 3(rai0) entering forwarding state br0: port 2(eth2.1) entering forwarding state iptables v1.4.10: Couldn't load target `br0: port 1(ra0) entering forwarding state port_forward':File not found Try `iptables -h' or 'iptables --help' for more information. iptables: No chain/target/match by that name. iptables v1.4.10: Couldn't load target `DMZ':File not found Try `iptables -h' or 'iptables --help' for more information. iptables: No chain/target/match by that name. 30 0 432000 0 br0: port 4(eth2.2) entering forwarding state sh: ddns.sh: not found switch register base addr to system register 0xb0000000 dut mac=80:3F:5D:B6:EA:E1 Filter_State=1 write offset 0x64, value 0x1 webs: Listening for HTTP requests at address 192.168.2.15 QoSInit warning, can't get bandwidth string from UI. warning, can't get bandwidth string from UI. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. ifconfig: ioctl 0x8913 failed: No such device ifconfig: ioctl 0x8913 failed: No such device 1969-12-31 19:00:19: (log.c.97) server started init: can't log to /dev/tty5 starting pid 2942, tty '/dev/ttyS1': '/bin/sh' BusyBox v1.12.1 (2016-11-07 16:57:22 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. # ping_router failed! help Built-in commands: ------------------- . : break cd chdir continue eval exec exit export false hash help local pwd read readonly return set shift source times trap true type ulimit umask unset wait #


printenv output:

bootcmd=tftp
bootdelay=5
baudrate=57600
ethaddr="00:AA:BB:CC:DD:10"
ipaddr=192.168.10.101
serverip=192.168.10.100
bootfile=firmware.bin
stdin=serial
stdout=serial
stderr=serial

Environment size: 177/4092 bytes


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/06/17 11:21
  • by thegoliath