Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
toh:asus:rt-g32 [2015/12/31 08:36] – links fixed tmomastoh:asus:rt-g32 [2019/02/12 22:11] (current) – 432 warning added tmomas
Line 1: Line 1:
 +====== ASUS RT-G32 ======
  
 +{{section>meta:infobox:432_warning#infobox_for_dataentries&noheader&nofooter&noeditbutton}}
 +
 +**Ralink**, Rev B1/C1 model.
 +
 +The device is a wireless N router with 
 +  * 1 not-detachable antenna
 +  * 4 Port 100/10 Switch
 +  * 1 Port 100/10 Wan Interface
 +  * 4 MB Flash
 +  * 16 MB SDRAM for Rev B1 or 32 MB - for Rev C1
 +
 +===== Hardware =====
 +==== Info ====
 +| **Architecture:**     | MIPS                    |
 +| **Vendor:**           | Asus                    |
 +| **Bootloader:**       | U-Boot                  |
 +| **System-On-Chip:**   | RT3052/RT3050F          |
 +| **CPU Speed:**        | 320 Mhz                 |
 +| **Flash-Chip:**       | MX25L3205D              |
 +| **Flash size:**       | 4 MiB                   |
 +| **RAM:**              | 16/32 MiB               |
 +| **Wireless:**         | RT2860                  |
 +| **Ethernet:**         | Switch in CPU           |
 +| **USB:**              | 1x2.0 (unsoldered)      |
 +| **Serial:**           | [[#Serial|Yes]]         |
 +| **JTAG:**             | N/A                     |
 +
 +===== Photos =====
 +{{media:asus:rt-g32.jpg?400|Asus RT-G32-B1 PCB layout}}
 +
 +===== Opening the case =====
 +**Note:** This will void your warranty!
 +
 +  - There are two screws underneath the rubber feet at the front of the device. Remove those.
 +  - Two additional screws are freely removeable at the bottom of the case. Don't forget these ;-)
 +  - Remove the top of the case with the transparent plastic piece.
 +
 +
 +===== Serial =====
 +The serial port is located between the FCC logo and the CE logo.\\
 +It's pinout is fairly documented by the PCB print: GND|RX|TX|VCC(3.3) (direction as seen from the front of the device).
 +The bootloader (U-Boot) and the original Asus firmware use a baudrate of 57600 with 8N1.
 +
 +
 +===== Compiling OpenWrt =====
 +**  NOTE: ** OpenWrt currently support this device only since attitude_adjustment.
 +
 +Get sources of openwrt & patch it:
 +
 +<code>svn://svn.openwrt.org/openwrt/branches/attitude_adjustment openwrt
 +cd openwrt</code>
 +
 +
 +Then compile openwrt in standard way, Target System ⇒ "Ralink RT288x/RT305x", Subtarget ⇒ "RT305x based boards":
 +
 +<code>make menuconfig
 +make</code>
 +
 +
 +===== Installation =====
 +==== Flashing via TFTP-Server (Only for Rev. B1) ====
 +
 +**NOTE:** Configured TFTP server needed!
 +
 +  * After successfull compiling firmware, move bin/ramips/openwrt-ramips-rt305x-rt-g32-b1-squashfs-sysupgrade.bin file into your TFTP server's directory.
 +  * Then rename that binary file to "ASUS_G32V2" - it must have exacly this name without extension.
 +  * Set Your server's IP-Address to 192.168.1.254/24
 +  * Then connect router to the network
 +  * Push and keep "Reset" button
 +  * Turn on router.
 +  * After 5 seconds - release "Reset button".
 +  * Wait about 3 minutes, the router will flash new firmware.
 +
 +==== Flashing via TFTP-Client Push (Only for Rev. C1) ====
 +
 +  * Fot this revision use firmware for RT-N10+ asus device
 +  * After successfull compiling firmware, rename bin/ramips/openwrt-ramips-rt305x-rt-n10-plus-squashfs-sysupgrade.bin file into something shorter, for example RT-G32.C1.bin.
 +  * Set your server's IP-Address to 192.168.1.15/24
 +  * Then connect router to the network
 +  * Push and keep "Reset" button
 +  * Turn on router.
 +  * After 5 seconds - release "Reset button".
 +  * Push firmware into the router.
 +  * Wait about 3 minutes, the router will flash new firmware.
 +
 +==== Pushing firmware into router ====
 +For aftp
 +<code>atftp --option "mode octet" --verbose -p -l RT-G32.C1.bin 192.168.1.1</code>
 +For tftp client on linux/Mac
 +<code>tftp 192.168.1.1
 +tftp>binary
 +tftp>put RT-G32.C1.bin</code>
 +For tftp client on Winows
 +<code>tftp -i 192.168.1.1 put RT-G32.C1.bin</code>
 +
 +
 +==== Flashing via U-Boot ====
 +
 +**NOTE:** Serial connection and configured TFTP server needed!
 +
 +  *   After successfull compiling firmware, move bin/ramips/openwrt-ramips-rt305x-rt-g32-b1-squashfs-sysupgrade.bin file into your TFTP server's directory.
 +  *   Then rename firmware to something shorter, for example "rt-g32-b1.bin" (the file name must be shorter than 32 symbols).
 +  *   Connect serial port to device (speed is 57600 8N1).
 +  *   When you power on device, and see U-Boot log, immediatly push "2" once.
 +You will see this message:
 +<code>2: System Load Linux Kernel then write to Flash via TFTP. 
 + Warning!! Erase Linux in Flash then burn new one. Are you sure?(Y/N)</code>
 +  *   Push "y", and enter: device IP, then TFTP server's IP, and then openwrt's firmware file name:
 +<code>
 + Please Input new ones /or Ctrl-C to discard
 +        Input device IP (192.168.1.1) ==:10.10.1.1
 +        Input server IP (192.168.1.2) ==:10.10.1.72
 +        Input Linux Kernel filename () ==:rt-g32-b1.bin
 +</code>
 +
 + If TFTP server installed correctly, the firmware would be downloaded at ~30 seconds.
 +Then it will be flashed into device (It will take about 2 minutes).
 +
 +
 +===== Bootlogs =====
 +==== OEM bootlog ====
 +<WRAP bootlog>
 +<nowiki>U-Boot 1.1.3 (Nov 12 2009 - 00:08:59)
 +
 +Board: Ralink APSoC DRAM:  16 MB
 +relocate_code Pointer at: 80fb4000
 +spi_wait_nsec: 3e 
 +spi deice id: c2 20 16 c2 20 (2016c220)
 +find flash: mx25l3205d
 +raspi_read: from:30000 len:1000 
 +*** Warning - bad CRC, using default environment
 +
 +============================================ 
 +
 +Ralink UBoot Version: 3.3
 +-------------------------------------------- 
 +ASIC 3052_MP2 (Port5<->None)
 +DRAM component: 128 Mbits SDR
 +DRAM bus: 16 bit
 +Total memory: 16 MBytes
 +Flash component: SPI Flash
 +Date:Nov 12 2009  Time:00:08:59
 +============================================ 
 +icache: sets:256, ways:4, linesz:32 ,total:32768
 +dcache: sets:128, ways:4, linesz:32 ,total:16384 
 +
 + ##### The CPU freq = 320 MHZ #### 
 +
 +SDRAM bus set to 16 bit 
 + SDRAM size =16 Mbytes
 +GPIO 10 not detect
 +
 +Please choose the operation: 
 +   1: Load system code to SDRAM via TFTP. 
 +   2: Load system code then write to Flash via TFTP. 
 +   3: Boot system code via Flash (default).
 +   4: Entr boot command line interface.
 +   9: Load Boot Loader code then write to Flash via TFTP. 
 + 1  0 
 +
 +3: System Boot system code via Flash.
 +## Booting image at bf050000 ...
 +raspi_read: from:50000 len:40 
 +   Image Name:   Linux Kernel Image
 +   Created:      2010-01-06  11:08:51 UTC
 +   Image Type:   MIPS Linux Kernel Image (lzma compressed)
 +   Data Size:    2936012 Bytes =  2.8 MB
 +   Load Address: 80000000
 +   Entry Point:  802e0000
 +raspi_read: from:50040 len:2ccccc 
 +   Verifying Checksum ... OK
 +   Uncompressing Kernel Image ... OK
 +No initrd
 +## Transferring control to Linux (at address 802e0000) ...
 +## Giving linux memsize in MB, 16
 +
 +Starting kernel ...
 +
 +
 +LINUX started...
 +
 + THIS IS ASIC
 +Linux version 2.6.21 (root@localhost.localdomain) (gcc version 3.4.2) #115 Mon Jan 4 11:49:43 EST 2010
 +
 + The CPU feqenuce set to 320 MHz
 +CPU revision is: 0001964c
 +Determined physical RAM map:
 + memory: 01000000 @ 00000000 (usable)
 +Built 1 zonelists.  Total pages: 4064
 +Kernel command line: console=ttyS1,57600n8 root=1f05
 +Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes.
 +Primary data cache 16kB, 4-way, linesize 32 bytes.
 +Synthesized TLB refill handler (20 instructions).
 +Synthesized TLB load handler fastpath (32 instructions).
 +Synthesized TLB store handler fastpath (32 instructions).
 +Synthesized TLB modify handler fastpath (31 instructions).
 +Cache parity protection disabled
 +cause = 9080001c, status = 1100ff00
 +PID hash table entries: 64 (order: 6, 256 bytes)
 +calculating r4koff... 00138800(1280000)
 +CPU frequency 320.00 MHz
 +Using 160.000 MHz high precision timer.
 +Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
 +Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +Memory: 13016k/16384k available (2595k kernel code, 3368k reserved, 344k data, 120k init, 0k highmem)
 +Mount-cache hash table entries: 512
 +NET: Registered protocol family 16
 +NET: Registered protocol family 2
 +Time: MIPS clocksource has been installed.
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 512 (order: 0, 4096 bytes)
 +TCP bind hash table entries: 512 (order: -1, 2048 bytes)
 +TCP: Hash tables configured (established 512 bind 512)
 +TCP reno registered
 +squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
 +squashfs: LZMA suppport for slax.org by jro
 +io scheduler noop registered (default)
 +Ralink gpio driver initialized
 +HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096
 +N_HDLC line discipline registered.
 +Serial: 8250/16550 driver $Revision: 1.3 $ 2 ports, IRQ sharing disabled
 +serial8250: ttyS0 at I/O 0xb0000500 (irq = 37) is a 16550A
 +serial8250: ttyS1 at I/O 0xb0000c00 (irq = 12) is a 16550A
 +loop: loaded (max 8 devices)
 +rdm_major = 254
 +===>Enter clean nat module
 +PPP generic driver version 2.4.2
 +PPP Deflate Compression module registered
 +PPP BSD Compression module registered
 +MPPE/MPPC encryption/compression module registered
 +NET: Registered protocol family 24
 +block2mtd: version $Revision: 1.1.1.1 $
 +deice id : c2 20 16 c2 20 (2016c220)
 +MX25L3205D(c2 2016c220) (4096 Kbytes)
 +mtd .name = raspi, .size = 0x00400000 (4M) .erasesize = 0x00010000 (64K) .numeraseregions = 0
 +Creating 7 MTD partitions on "raspi":
 +0x00000000-0x00400000 : "ALL"
 +0x00000000-0x00030000 : "Bootloader"
 +0x00030000-0x00040000 : "Config"
 +0x00040000-0x00050000 : "Factory"
 +0x00050000-0x00139d0c : "Kernel"
 +mtd: partition "Kernel" doesn't end on an erase block -- force read-only
 +0x00139d0c-0x01000000 : "RootFS"
 +mtd: partition "RootFS" extends beyond the end of device "raspi" -- size truncated to 0x2c62f4
 +mtd: partition "RootFS" doesn't start on an erase block boundary -- force read-only
 +0x00050000-0x01000000 : "Kernel_RootFS"
 +mtd: partition "Kernel_RootFS" extends beyond the end of device "raspi" -- size truncated to 0x3b0000
 +nf_conntrack version 0.5.0 (768 buckets, 6144 max)
 +IPv4 over IPv4 tunneling driver
 +PPTP driver version 0.8.3
 +ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone
 +netfilter PSD loaded - (c) astaro AG
 +unclean match register
 +TCP cubic registered
 +NET: Registered protocol family 1
 +NET: Registered protocol family 10
 +NET: Registered protocol family 17
 +802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
 +All bugs added by David S. Miller <davem@redhat.com>
 +GDMA1_MAC_ADRH -- : 0x00000000
 +GDMA1_MAC_ADRL -- : 0x00000000
 +Ralink APSoC Ethernet Driver Initilization. v2.00  256 rx/tx descriptors allocated, mtu = 1500!
 +GDMA1_MAC_ADRH -- : 0x000090e6
 +GDMA1_MAC_ADRL -- : 0xbabef887
 +PROC INIT OK!
 +
 + phy_id0 = 81808100 ,Port0_Status=Link down
 +VFS: Mounted root (squashfs filesystem) readonly.
 +Freeing unused kernel memory: 120k freed
 +
 +init started: BusyBox v1.12.1 (2009-12-26 10:56:46 EST)
 +
 +starting pid 11, tty ' ': '/etc_ro/rcS'
 +Algorithmics/MIPS FPU Emulator v1.5
 +devpts: called with bogus options
 +m
 +set nvram pid=17
 +mount: cannot read /etc/fstab: No such file or directory
 +192.168.1.1
 +2.0.0.5
 +Password for 'admin' changed
 +
 +phy_tx_ring = 0x00ae1000, tx_ring = 0xa0ae1000
 +
 +phy_rx_ring = 0x00000000, rx_ring = 0x00000000
 +RT305x_ESW: Link Status Changed
 +
 +phy_id0 = 0 ,Port0_Status=Link down
 +CDMA_CSG_CFG = 81000007
 +GDMA1_FWD_CFG = 710000
 +brctl: bridge br0: No such device
 +eth2.1: dev_set_promiscuity(master, 1)
 +device eth2 entered promiscuous mode
 +device eth2.1 entered promiscuous mode
 +switch reg write offset=14, value=405555
 +switch reg write offset=50, value=2001
 +switch reg write offset=98, value=7f3f
 +switch reg write offset=e4, value=3f
 +switch reg write offset=40, value=1001
 +switch reg write offset=44, value=1001
 +switch reg write offset=48, value=1002
 +switch reg write offset=70, value=ffff506f
 +/etc_ro/rcS: line 67: FlowCounter: not found
 +
 +starting pid 161, tty '/dev/ttyS1': '/bin/sh'
 +
 +
 +BusyBox v1.12.1 (2009-12-26 10:56:46 EST) built-in shell (ash)
 +Enter 'help' for a list of built-in commands.
 +
 +# killall: crond: no process killed
 +Jan  1 00:00:06 crond[167]: crond (busybox 1.12.1) started, log level 8
 +
 +
 +Commit crc = a7f24398
 +Set: phy[1].reg[0] = 3900
 +Set: phy[2].reg[0] = 3900
 +Set: phy[3].reg[0] = 3900
 +Set: phy[0].reg[0] = 3900
 +rt2860v2_ap: module license 'unspecified' taints kernel.
 +
 +
 +=== pAd = c0009000, size = 495344 ===
 +
 +<-- RTMPAllocAdapterBlock, Status=0
 +cat: can't open '/etc/l2wSchedule.txt': No such file or directory
 +cat: can't open '/etc/urlSchedule.txt': No such file or directory
 +killall: crontab: no process killed
 +RX DESC a06e6000  size = 2048
 +<-- RTMPAllocTxRxRingMemory, Status=0
 +Key1Str is Invalid key length(0) or Type(0)
 +Key2Str is Invalid key length(0) or Type(0)
 +Key3Str is Invalid key length(0) or Type(0)
 +Key4Str is Invalid key length(0) or Type(0)
 +1. Phy Mode = 0
 +2. Phy Mode = 0
 +3. Phy Mode = 0
 +MCS Set = 00 00 00 00 00
 +SYNC - BBP R4 to 20MHz.l
 +Main bssid = 90:e6:ba:be:f8:87
 +<==== rt28xx_init, Status=0
 +0x1300 = 00064380
 +Terminate the task(RtmpWscTask) with pid(267)!
 +RX DESC a0af8000  size = 2048
 +<-- RTMPAllocTxRxRingMemory, Status=0
 +Key1Str is Invalid key length(0) or Type(0)
 +Key2Str is Invalid key length(0) or Type(0)
 +Key3Str is Invalid key length(0) or Type(0)
 +Key4Str is Invalid key length(0) or Type(0)
 +1. Phy Mode = 0
 +2. Phy Mode = 0
 +3. Phy Mode = 0
 +MCS Set = 00 00 00 00 00
 +SYNC - BBP R4 to 20MHz.l
 +Main bssid = 90:e6:ba:be:f8:87
 +<==== rt28xx_init, Status=0
 +0x1300 = 00064380
 +==> Finish wirelss Basic Setting
 +==> Start Init WPS config
 +<== End Init WPS config
 +device ra0 entered promiscuous mode
 +killall: rt2860apd: no process killed
 +switch reg write offset=40, value=1001
 +switch reg write offset=44, value=1001
 +switch reg write offset=48, value=1002
 +switch reg write offset=70, value=ffff506f
 +killall: udhcpc: no process killed
 +killall: ntpclient: no process killed
 +killall: l2tp_dod.sh: no process killed
 +killall: accel-pptp.sh: no process killed
 +killall: config-pptp.sh: no process killed
 +killall: config-l2tp.sh: no process killed
 +killall: igmpproxy: no process killed
 +killall: ping: no process killed
 +eth2.2: Setting MAC address to  90 e6 ba be f8 87.
 +VLAN (eth2.2):  Underlying device (eth2) has same MAC, not checking promiscious mode.
 +udhcpc (v1.12.1) started
 +iptables: No chain/target/match by that name
 +clean nat conn: clean all of the connection track
 +killall: udhcpd: no process killed
 +time.nist.gov: Unknown host
 +br0: port 2(ra0) entering learning state
 +br0: port 1(eth2.1) entering learning state
 +killall: udhcpd: no process killed
 +Set: phy[1].reg[0] = 3100
 +rmmod: nf_nat_pptp: No such file or directory
 +rmmod: nf_conntrack_pptp: No such file or directory
 +rmmod: nf_nat_proto_gre: No such file or directory
 +rmmod: nf_conntrack_proto_gre: No such file or directory
 +iptables: No chain/target/match by that name
 +clean nat conn: clean all of the connection track
 +Set: phy[2].reg[0] = 3100
 +Set: phy[3].reg[0] = 3100
 +Set: phy[0].reg[0] = 3100
 +cat: can't open '/etc/l2wSchedule.txt': No such file or directory
 +killall: crontab: no process killed
 +webdir=/etc_ro/web
 +config ok
 +killall: miniupnpd: no process killed
 +iptables: No chain/target/match by that name
 +iptables v1.3.5: Couldn't find target `MINIUPNPD'
 +
 +Try `iptables -h' or 'iptables --help' for more information.
 +iptables v1.3.5: Couldn't find target `MINIUPNPD'
 +
 +Try `iptables -h' or 'iptables --help' for more information.
 +iptables: No chain/target/match by that name
 +iptables: No chain/target/match by that name
 +iptables v1.3.5: Couldn't find target `MINIUPNPD'
 +
 +Try `iptables -h' or 'iptables --help' for more information.
 +iptables v1.3.5: Couldn't find target `MINIUPNPD'
 +
 +Try `iptables -h' or 'iptables --help' for more information.
 +iptables: No chain/target/match by that name
 +restart ok
 +br0: topology change detected, propagating
 +br0: port 2(ra0) entering forwarding state
 +br0: topology change detected, propagating
 +br0: port 1(eth2.1) entering forwarding state
 +time.nist.gov: Unknown host</nowiki>
 +</WRAP>\\
 +
 +
 +==== OpenWrt bootlog ====
 +
 +<WRAP bootlog>
 +<nowiki>U-Boot 1.1.3 (Nov 12 2009 - 00:08:59)
 +
 +Board: Ralink APSoC DRAM:  16 MB
 +relocate_code Pointer at: 80fb4000
 +spi_wait_nsec: 3e 
 +spi deice id: c2 20 16 c2 20 (2016c220)
 +find flash: mx25l3205d
 +raspi_read: from:30000 len:1000 
 +raspi_read: from:30000 len:1000 
 +============================================ 
 +Ralink UBoot Version: 3.3
 +-------------------------------------------- 
 +ASIC 3052_MP2 (Port5<->None)
 +DRAM component: 128 Mbits SDR
 +DRAM bus: 16 bit
 +Total memory: 16 MBytes
 +Flash component: SPI Flash
 +Date:Nov 12 2009  Time:00:08:59
 +============================================ 
 +icache: sets:256, ways:4, linesz:32 ,total:32768
 +dcache: sets:128, ways:4, linesz:32 ,total:16384 
 +
 + ##### The CPU freq = 320 MHZ #### 
 +
 +SDRAM bus set to 16 bit 
 + SDRAM size =16 Mbytes
 +GPIO 10 not detect
 +
 +Please choose the operation: 
 +   1: Load system code to SDRAM via TFTP. 
 +   2: Load system code then write to Flash via TFTP. 
 +   3: Boot system code via Flash (default).
 +   4: Entr boot command line interface.
 +   9: Load Boot Loader code then write to Flash via TFTP. 
 + 0 
 +   
 +3: System Boot system code via Flash.
 +## Booting image at bf050000 ...
 +raspi_read: from:50000 len:40 
 +   Image Name:   MIPS OpenWrt Linux-2.6.37.6
 +   Created:      2011-05-26  15:52:55 UTC
 +   Image Type:   MIPS Linux Kernel Image (lzma compressed)
 +   Data Size:    774839 Bytes = 756.7 kB
 +   Load Address: 80000000
 +   Entry Point:  80000000
 +raspi_read: from:50040 len:bd2b7 
 +   Verifying Checksum ... OK
 +   Uncompressing Kernel Image ... OK
 +No initrd
 +## Transferring control to Linux (at address 80000000) ...
 +## Giving linux memsize in MB, 16
 +
 +Starting kernel ...
 +
 +Linux version 2.6.37.6 (tipok@mythbox) (gcc version 4.5.2 (Linaro GCC 4.5-2011.02-0) ) #1 Thu May 26 18:52:48 EEST 2011
 +bootconsole [early0] enabled
 +CPU revision is: 0001964c (MIPS 24Kc)
 +Ralink RT3350   id:1 rev:2 running at 320.00 MHz
 +Determined physical RAM map:
 + memory: 01000000 @ 00000000 (usable)
 +Initrd not found or empty - disabling initrd
 +Zone PFN ranges:
 +  Normal   0x00000000 -> 0x00001000
 +Movable zone start PFN for each node
 +early_node_map[1] active PFN ranges
 +    0: 0x00000000 -> 0x00001000
 +Built 1 zonelists in Zone order, mobility grouping off.  Total pages: 4064
 +Kernel command line:  board=RT-G32-revB mtdparts=spi-flash.0:192k(u-boot)ro,64k(u-boot-env)ro,64k(factory)ro,832k(kernel),2944k(rootfs),3776k@0x50000(firmware) console=ttyS1,576002
 +PID hash table entries: 64 (order: -4, 256 bytes)
 +Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
 +Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
 +Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes.
 +Primary data cache 16kB, 4-way, VIPT, no aliases, linesize 32 bytes
 +Writing ErrCtl register=00006bf0
 +Readback ErrCtl register=00006bf0
 +Memory: 13776k/16384k available (1781k kernel code, 2608k reserved, 299k data, 144k init, 0k highmem)
 +SLUB: Genslabs=9, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
 +NR_IRQS:48
 +console [ttyS1] enabled, bootconsole disabled
 +console [ttyS1] enabled, bootconsole disabled
 +Calibrating delay loop... 212.99 BogoMIPS (lpj=1064960)
 +pid_max: default: 32768 minimum: 301
 +Mount-cache hash table entries: 512
 +NET: Registered protocol family 16
 +MIPS: machine is Asus RT-G32 revB
 +bio: create slab <bio-0> at 0
 +Switching to clocksource MIPS
 +NET: Registered protocol family 2
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 512 (order: 0, 4096 bytes)
 +TCP bind hash table entries: 512 (order: -1, 2048 bytes)
 +TCP: Hash tables configured (established 512 bind 512)
 +TCP reno registered
 +UDP hash table entries: 256 (order: 0, 4096 bytes)
 +UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +NET: Registered protocol family 1
 +squashfs: version 4.0 (2009/01/31) Phillip Lougher
 +JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +msgmni has been set to 26
 +io scheduler noop registered
 +io scheduler deadline registered (default)
 +Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
 +serial8250: ttyS0 at MMIO 0x10000500 (irq = 13) is a 16550A
 +serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A
 +m25p80 spi0.0: mx25l3205d (4096 Kbytes)
 +Creating 6 MTD partitions on "spi-flash":
 +0x000000000000-0x000000030000 : "u-boot"
 +0x000000030000-0x000000040000 : "devdata"
 +0x000000040000-0x000000050000 : "devconf"
 +0x000000050000-0x000000120000 : "kernel"
 +0x000000120000-0x000000400000 : "rootfs"
 +mtd: partition "rootfs" set to be root filesystem
 +mtd: partition "rootfs_data" created automatically, ofs=250000, len=1B0000 
 +0x000000250000-0x000000400000 : "rootfs_data"
 +0x000000050000-0x000000400000 : "openwrt"
 +TCP westwood registered
 +NET: Registered protocol family 17
 +802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
 +All bugs added by David S. Miller <davem@redhat.com>
 +VFS: Mounted root (squashfs filesystem) readonly on device 31:4.
 +Freeing unused kernel memory: 144k freed
 +- preinit -
 +Press the [f] key and hit [enter] to enter failsafe mode
 +- regular preinit -
 +JFFS2 notice: (286) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 32 of xref (0 dead, 4 orphan) found.
 +switching to jffs2
 +- init -
 +
 +Please press Enter to activate this console. Compat-wireless backport release: compat-wireless-2011-05-11-1-g501c91f
 +Backport based on wireless-testing.git master-2011-05-13
 +device eth0.1 entered promiscuous mode
 +device eth0 entered promiscuous mode
 +cfg80211: Calling CRDA to update world regulatory domain
 +br-lan: port 1(eth0.1) entering forwarding state
 +br-lan: port 1(eth0.1) entering forwarding state
 +PPP generic driver version 2.4.2
 +ip_tables: (C) 2000-2006 Netfilter Core Team
 +NET: Registered protocol family 24
 +cfg80211: World regulatory domain updated:
 +cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
 +cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +nf_conntrack version 0.5.0 (217 buckets, 868 max)</nowiki>
 +</WRAP>\\
 +
 +===== Tags =====
 +[[meta:tags|How to add tags]]
 +{{tag>ramips rt3050 FastEthernet MIPS MIPS32 24KEc 4flash}}