ASUS RT-AX89X B
Only B revisions of the AX89X are supported, check the bottom sticker before you proceed!
Supported Versions
Hardware Highlights
Installation
Installation instructions: -------------------------- 1. Upload openwrt-qualcommax-ipq807x-asus_rt-ax89x-initramfs-factory.trx via the stock firmware. Administration -> Firmware Upgrade -> Manual Firmware update (Upload) After flashing, the device will reboot with OpenWrt initramfs, and it can be accessed via any of the LAN ports, using SSH with the usual OpenWrt default credentials. Note: If you reboot the device at this point, it'll revert back to the Asus firmware. 2. Run sysupgrade from within the OpenWrt initramfs: * Copy (using scp, or wget) openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin to the /tmp/ folder of the running initramfs image. * Install OpenWrt by executing sysupgrade -n /tmp/openwrt-qualcommax-ipq807x-asus_rt-ax89x-squashfs-sysupgrade.bin
Ramdisks (initramfs)
Standard Uboot ; has serial and tftp boot prompt.
Debricking
→ generic.debrick Update: Successful debrick can be accomplished with the default uboot ; meaning easy recovery is possible !
Method:
- Setup interface on Host PC with ip 192.168.50.75/24 (not the Router will ONLY accept tftp put over this IP) ; $ip a a 192.168.50.75/24 dev <NICDEV>
- The HostNIC and recovery is performed ONLY over the 1G WAN port NIC (this is the 'blue') NIC port next to the 10G Copper port.
- Find valid recovery .trx
- Run tftp to 192.168.50.1 ; $tftp 192.168.50.1
- Unplug DC barrel jack whilst holding down the reset switch with a pointy thing
- Leave Power Button Depressed(on)
- Replug DC barrel jack whilst still holding reset switch with a pointy thing ; release after first LED indication
- Power LED will flash slowly
- Use TFTP client to put target firmware in bin mode; set trace to show progess; $tftp>trace ; $tftp>bin; $tftp>put <validfile>.trx
- Trace will show transfer ; wait for router to reboot.
Note - this WILL NOT clear the NVRAM ; meaning you will need to connect with the user-pass/network setup previously. A reset can be performed with the stock firmware, with a 30/30/30 reset method from powered up state.
Hardware
Main SoC
Photos
Album here:
Opening the case
Note: This will possibly void your warranty in some jurisdictions. Here in NZ 'Void if removed' stickers are a 100% illegal and in breach of our Consumer laws. IANAL.
- Remove two of the Bottom case pads which hide two Screws
- Remove the lower portion of the Serial/Info Sticky on the bottom revealing the third through screw
- Work an edge around the lip of the top cover circling the top case caseful several times wiggling it up and down with the edge to release clips
Hardware notes
Excellent Next-gen target, Qualcomm Soc, Dual 10Gbit ports, 1 Copper (with 802.3bz 2.5/5/10G fallback sense) and an SFP+ cage; so can take an SFP+ ONT or DAC/Fibre. And 9 Gigabit ports attached to 3 separate phys-macs and 2 different switches internally. Qualcomm ipq8074 8×8 Radio with WiFi 6 (802.11ax) support.
JTAG
→ port.jtag general information about the JTAG port, JTAG cable, etc.
There is a JTAG port with male headers soldered, there also appears to be a free and exposed set of I2C pins in addition to the JTAG meaning there are free GPIO's on the SoC. Router requires DC powering so leave the VCC pin unconnected.
How to connect to the JTAG Port of this specific device:
Photo of PCB with markings
Bootlogs
OEM bootlog
Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00114 S - IMAGE_VARIANT_STRING=HAACANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x000002e5 B - 205 - PBL, Start B - 2748 - bootable_media_detect_entry, Start B - 3454 - bootable_media_detect_success, Start B - 3459 - elf_loader_entry, Start B - 6286 - auth_hash_seg_entry, Start B - 6546 - auth_hash_seg_exit, Start B - 78027 - elf_segs_hash_verify_entry, Start B - 150014 - PBL, End B - 165096 - SBL1, Start B - 218166 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4 B - 224785 - pm_device_init, Start B - 349194 - PM_SET_VAL:Skip D - 123647 - pm_device_init, Delta B - 351451 - pm_driver_init, Start D - 5398 - pm_driver_init, Delta B - 358009 - clock_init, Start D - 2196 - clock_init, Delta B - 361913 - boot_flash_init, Start D - 8601 - boot_flash_init, Delta B - 374265 - boot_config_data_table_init, Start D - 3080 - boot_config_data_table_init, Delta - (575 Bytes) B - 381768 - Boot Setting : 0x00000618 B - 385672 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:0 B - 392596 - sbl1_ddr_set_params, Start B - 396469 - cpr_init, Start D - 1067 - cpr_init, Delta B - 401685 - Pre_DDR_clock_init, Start B - 405772 - Pre_DDR_clock_init, End B - 409157 - DDR Type : PCDDR3 B - 414769 - do ddr sanity test, Start D - 976 - do ddr sanity test, Delta B - 419619 - DDR: Start of HAL DDR Boot Training B - 424346 - DDR: End of HAL DDR Boot Training B - 429928 - DDR: Checksum to be stored on flash is -1518788596 B - 440206 - Image Load, Start D - 246013 - QSEE Image Loaded, Delta - (1376536 Bytes) B - 686311 - Image Load, Start D - 610 - SEC Image Loaded, Delta - (2048 Bytes) B - 693936 - Image Load, Start D - 43188 - DEVCFG Image Loaded, Delta - (32033 Bytes) B - 737185 - Image Load, Start D - 22936 - RPM Image Loaded, Delta - (99896 Bytes) B - 760182 - Image Load, Start D - 107055 - APPSBL Image Loaded, Delta - (691864 Bytes) B - 867359 - QSEE Execution, Start D - 30 - QSEE Execution, Delta B - 873123 - USB D+ check, Start D - 0 - USB D+ check, Delta B - 879589 - SBL1, End D - 716689 - SBL1, Delta S - Flash Throughput, 7042 KB/s (2202952 Bytes, 312797 us) S - DDR Frequency, 466 MHz S - Core 0 Frequency, 1651 MHz U-Boot 2016.01 (May 21 2019 - 10:52:55 +0800) RT-AX89U bootloader version: 1.1.1.3 DRAM: smem ram ptable found: ver: 1 len: 4 ASUS RT-AX89U gpio init : buttons 1 GiB NAND: ONFI device found ID = 1590aaef Vendor = ef Device = aa SF: Unsupported flash IDs: manuf ff, jedec ffff, ext_jedec ffff ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 256 MiB MMC: *** Warning - bad CRC, using default environment In: serial@78B3000 Out: serial@78B3000 Err: serial@78B3000 Check bootloader area ... machid: 8010000 Net: MAC0 addr:0:aa:bb:cc:dd:e0 PORT0/5/6_PAD_CTRL 0x05080000/01000000/00000080 PORT0/5/6_STATUS 0x0000007e/00001280/00000230 8075 PHY ID1: 0x4d 8075 PHY ID2: 0xd0b1 switch_mac_mode: 0x5/ff/2 EDMA ver 1 hw init Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7) RxDesc:1 (15-15) RxFill:1 (7-7) ipq807x_edma_alloc_rings: successfull ipq807x_edma_setup_ring_resources: successfull ipq807x_edma_configure_rings: successfull ipq807x_edma_hw_init: successfull eth0 ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=2", size 252 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 2016, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 347767136 ubi0: available PEBs: 0, total reserved PEBs: 2016, PEBs reserved for bad PEB handling: 40 UBI: vol_id reserved_pebs alignment data_pad vol_type usable_leb_size used_ebs used_bytes last_eb_bytes corrupted upd_marker name_len name UBI: 0 3 1 0 dynamic 1f000 3 5d000 1f000 0 0 5 nvram UBI: 1 3 1 0 dynamic 1f000 3 5d000 1f000 0 0 7 Factory UBI: 2 3 1 0 dynamic 1f000 3 5d000 1f000 0 0 8 Factory2 UBI: 3 33a 1 0 dynamic 1f000 33a 6406000 1f000 0 0 5 linux UBI: 5 471 1 0 dynamic 1f000 471 89af000 1f000 0 0 5 jffs2 UBI: 7fffefff 2 1 0 dynamic 1f000 2 3e000 2 0 0 d layout volume UBI volume [jffs2] id 5 mismatch! (expect 4) Read 5d000 bytes from volume Factory offset 0 to 4a082720 EEPROM set 0: OK (version 19) Read 5d000 bytes from volume Factory2 offset 0 to 4a082720 EEPROM set 1: OK (version 19) Read 5d000 bytes from volume Factory offset 0 to 4a0e2ba0 Select EEPROM set 0 at offset 0x0. Please choose the operation: 1: Load System code to SDRAM via TFTP. 2: Load System code then write to Flash via TFTP. 3: Boot System code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: Boot System code via Flash (default). RT-AX89U bootloader version: 1.1.1.3 MAC Address: A8:5E:45:95:DB:50 Read 40 bytes from volume linux offset 0 to 4b000000 Read 30b92b8 bytes from volume linux offset 40 to 4b000040 ## Booting kernel from Legacy Image at 4b000000 ... Image Name: Image Type: ARM Linux Kernel Image (lzma compressed) Data Size: 51090104 Bytes = 48.7 MiB Load Address: 42208000 Entry Point: 42208000 Verifying Checksum ... OK CRC check good on phy fw file (0x512A) PHYFW:Loading IRAM...........done. PHYFW:Loading DRAM..............done. phy fw image load good CRC-16 matches (0x56D5) AQR PHY ID1: 0x3a1 AQR PHY ID2: 0xb4e2 ## Booting kernel from Legacy Image at 4b000000 ... Image Name: Image Type: ARM Linux Kernel Image (lzma compressed) Data Size: 51090104 Bytes = 48.7 MiB Load Address: 42208000 Entry Point: 42208000 Uncompressing Kernel Image ... OK Loading Device Tree to 4a0c8000, end 4a0de0c0 ... OK Using machid 0x8010000 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.60 (root@asus) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Tue Feb 4 12:11:36 CST 2020 [ 0.000000] CPU: ARMv7 Processor [410fd034] revision 4 (ARMv7), cr=10c0383d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] Machine model: Qualcomm Technologies, Inc. IPQ807x/AP-HK01 [ 0.000000] Ignoring memory range 0x40000000 - 0x42000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] PERCPU: Embedded 12 pages/cpu @bd7cb000 s19392 r8192 d21568 u49152 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 225600 [ 0.000000] Kernel command line: console=ttyMSM0,115200n8 rootfstype=squashfs root=/dev/mtdblock4 swiotlb=1 ubi.mtd=UBI_DEV [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Memory: 894432K/910336K available (5047K kernel code, 220K rwdata, 1624K rodata, 252K init, 257K bss, 15904K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xbe800000 - 0xff800000 (1040 MB) [ 0.000000] lowmem : 0x80000000 - 0xbe000000 ( 992 MB) [ 0.000000] pkmap : 0x7fe00000 - 0x80000000 ( 2 MB) [ 0.000000] modules : 0x7f000000 - 0x7fe00000 ( 14 MB) [ 0.000000] .text : 0x80208000 - 0x8088c1c0 (6673 kB) [ 0.000000] .init : 0x8088d000 - 0x808cc000 ( 252 kB) [ 0.000000] .data : 0x808cc000 - 0x80903214 ( 221 kB) [ 0.000000] .bss : 0x80906000 - 0x80946714 ( 258 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Invalid signature of oopsbuf: 41-40-00-48-15-9C-28-55 (len 817998946) [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:16 nr_irqs:16 16 [ 0.000000] Architected cp15 timer(s) running at 19.20MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000003] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.000009] Switching to timer-based delay loop, resolution 52ns [ 0.000376] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000) [ 0.000383] pid_max: default: 32768 minimum: 301 [ 0.000426] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000431] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000692] CPU: Testing write buffer coherency: ok [ 0.000912] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.000941] Setting up static identity map for 0x42208280 - 0x422082d8 [ 0.050136] MSM Memory Dump base table set up [ 0.050149] MSM Memory Dump apps data table set up [ 0.080186] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.110162] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 [ 0.140176] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 [ 0.140199] Brought up 4 CPUs [ 0.140209] SMP: Total of 4 processors activated (153.60 BogoMIPS). [ 0.140212] CPU: All CPU(s) started in SVC mode. [ 0.140423] devtmpfs: initialized [ 0.150708] VFP support v0.3: implementor 41 architecture 3 part 40 variant 3 rev 4 [ 0.150898] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.150913] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.151138] pinctrl core: initialized pinctrl subsystem [ 0.151693] NET: Registered protocol family 16 [ 0.152226] DMA: preallocated 2048 KiB pool for atomic coherent allocations [ 0.180039] cpuidle: using governor ladder [ 0.210048] cpuidle: using governor menu [ 0.216094] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ! [ 0.224369] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. [ 0.224377] hw-breakpoint: maximum watchpoint size is 8 bytes. [ 0.225486] CPU: IPQ8074, SoC Version: 1.2 [ 0.225657] <CORE> glink_init: IPC Logging Disabled [ 0.225870] <CORE> glink_core_register_transport: IPC Logging disabled [ 0.225912] msm_glink_smem_native_xprt rx fifo not found [ 0.226096] <CORE> glink_core_register_transport: IPC Logging disabled [ 0.226120] glink_core_link_up glink is up [ 0.251086] SCSI subsystem initialized [ 0.252553] cfg80211: World regulatory domain updated: [ 0.252558] cfg80211: DFS Master region: unset [ 0.252562] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 0.252567] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 0.252573] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 0.252577] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 0.252582] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 0.252587] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 0.252592] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 0.252596] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 0.252600] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 0.252773] clocksource: Switched to clocksource arch_sys_counter [ 0.254973] NET: Registered protocol family 2 [ 0.255250] TCP established hash table entries: 8192 (order: 3, 32768 bytes) [ 0.255291] TCP bind hash table entries: 8192 (order: 4, 65536 bytes) [ 0.255360] TCP: Hash tables configured (established 8192 bind 8192) [ 0.255387] UDP hash table entries: 512 (order: 2, 16384 bytes) [ 0.255405] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes) [ 0.255490] NET: Registered protocol family 1 [ 0.256364] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available [ 0.259832] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.262135] Key type asymmetric registered [ 0.262143] Asymmetric key parser 'x509' registered [ 0.262164] io scheduler noop registered [ 0.262170] io scheduler deadline registered (default) [ 0.262187] io scheduler cfq registered [ 0.266356] NET: Registered protocol family 27 [ 0.266364] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled [ 0.266372] qmi_log_init: IPC Logging disabled [ 0.266375] qmi_log_init: IPC Logging disabled [ 0.266422] msm_rpm_log_probe: OK [ 0.267043] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set [ 0.269159] msm_serial 78b3000.serial: msm_serial: detected port #0 [ 0.269182] msm_serial 78b3000.serial: uartclk = 3686400 [ 0.269206] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 22, base_baud = 230400) is a MSM [ 0.269221] msm_serial: console setup on port #0 [ 0.931515] console [ttyMSM0] enabled [ 0.936579] msm_serial: driver initialized [ 0.939969] msm_serial_hsl_init: driver initialized [ 0.944521] brd: module loaded [ 0.949666] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xaa [ 0.951642] nand: Winbond W29N02GZ [ 0.958180] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.961540] 2 ofpart partitions found on MTD device qcom_nand.0 [ 0.968938] Creating 2 MTD partitions on "qcom_nand.0": [ 0.974748] 0x000000000000-0x0000003e0000 : "Bootloader" [ 0.982747] 0x000000400000-0x000010000000 : "UBI_DEV" [ 1.140716] spmi spmi-0: PMIC Arb Version-2 (0x20010000) [ 1.142197] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 1.148019] IMQ driver loaded successfully. (numdevs = 8, numqueues = 1, imq_dev_accurate_stats = 1) [ 1.151424] Hooking IMQ after NAT on PREROUTING. [ 1.160550] Hooking IMQ before NAT on POSTROUTING. [ 1.165433] libphy: Fixed MDIO Bus: probed [ 1.610277] qca-mdio 90000.mdio: Could not find phy-reset-gpio [ 1.610353] libphy: qca_mdio: probed [ 1.615976] qca-mdio 90000.mdio: qca-mdio driver was registered [ 1.618879] PPP generic driver version 2.4.2 [ 1.624491] PPP MPPE Compression module registered [ 1.628881] NET: Registered protocol family 24 [ 1.633512] PPTP driver version 0.8.5 [ 1.637975] cnss: Unable to create IPC log context! [ 1.641701] cnss: Platform driver probed successfully. [ 1.646479] cnss: Platform driver probed successfully. [ 1.651644] i2c /dev entries driver [ 1.657712] gpio-fan gpio-fan: GPIO fan initialized [ 1.664778] [ 1.664778] Version Rollback Feature Disabled [ 1.665969] SPMI VADC - Min ch: 0 Max ch: 15 [ 1.672317] u32 classifier [ 1.675249] Performance counters on [ 1.677766] nf_conntrack version 0.5.0 (13975 buckets, 55900 max) [ 1.681822] xt_time: kernel timezone is -0000 [ 1.687852] gre: GRE over IPv4 demultiplexor driver [ 1.692179] ip_tables: (C) 2000-2006 Netfilter Core Team [ 1.696850] arp_tables: (C) 2002 David S. Miller [ 1.702635] NET: Registered protocol family 10 [ 1.707804] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 1.711216] NET: Registered protocol family 17 [ 1.716663] NET: Registered protocol family 15 [ 1.721000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 1.725445] Bridge firewalling registered [ 1.738192] l2tp_core: L2TP core driver, V2.0 [ 1.742078] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 1.746421] 8021q: 802.1Q VLAN Support v1.8 [ 1.751180] Registering SWP/SWPB emulation handler [ 1.759690] pmd9655_s4: supplied by e-smps1-reg [ 1.760140] cpr3_mem_acc_init: npu: not using memory accelerator regulator [ 1.764489] npu_corner: fused NOM: open-loop= 808000 uV [ 1.771419] npu_corner: fused TURBO: open-loop= 864000 uV [ 1.777506] pmd9655_s3: supplied by e-smps1-reg [ 1.782949] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0 [ 1.787130] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 3 [ 1.793853] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0 [ 1.801391] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable [ 1.808877] cpr3_mem_acc_init: apc: not using memory accelerator regulator [ 1.818041] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV [ 1.824987] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 824000 uV [ 1.834982] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 880000 uV [ 1.844782] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 952000 uV [ 1.854621] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 648, quot_offset[ 7]= 0 [ 1.864399] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 887, quot_offset[ 7]= 235 [ 1.875251] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]= 985, quot_offset[ 7]= 95 [ 1.886185] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1127, quot_offset[ 7]= 140 [ 1.897193] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop [ 1.908945] ubi0: attaching mtd1 [ 2.082292] random: nonblocking pool is initialized [ 2.889130] ubi0: scanning is finished [ 2.894880] ubi0: attached mtd1 (name "UBI_DEV", size 252 MiB) [ 2.894898] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 2.899593] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 2.906463] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 2.913313] ubi0: good PEBs: 2016, bad PEBs: 0, corrupted PEBs: 0 [ 2.920078] ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128 [ 2.926335] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 347767136 [ 2.933456] ubi0: available PEBs: 0, total reserved PEBs: 2016, PEBs reserved for bad PEB handling: 40 [ 2.942400] ubi0: background thread "ubi_bgt0d" started, PID 204 [ 2.951991] gluebi_create: Hook read/write method of Factory. [ 2.958304] gluebi_create: Hook read/write method of Factory2. [ 3.001633] [Factory-0]: OK (ver: 19) [ 3.039290] [Factory2-0]: OK (ver: 19) [ 3.039303] Select [Factory-0] [ 3.042669] Found DTB, length 130c1 [ 3.045005] Creating 1 MTD partitions on "linux": [ 3.048340] 0x0000002a468c-0x000006406000 : "rootfs" [ 3.053508] mtd: device 6 (rootfs) set to be root filesystem [ 3.058239] gluebi_create: skip jffs2 volume [ 3.068015] pmd9655_ldo11: disabling [ 3.068685] Override root device as 31:6 [ 3.073691] VFS: Mounted root (squashfs filesystem) readonly on device 31:6. [ 3.077696] devtmpfs: mounted [ 3.082737] Freeing unused kernel memory: 252K (8088d000 - 808cc000) init_main start /dev/nvram: No such file or directory [ 3.576297] offset 0x38800 elapse 10ms 1: set_action 0 Hit ENTER for console... firmware version: 3.0.0.4.384_81377-gc8d8dff bootloader version: RT-AX89U-01-01-01-03 firmware version: 3.0.[ 5.628727] bled: GPIO#20: netdev eth5. [ 5.634882] bled: GPIO#47: switch ports mask 0. [ 5.636001] bled: GPIO#36: netdev eth4. [ 5.641208] bled: GPIO#35: switch ports mask 0. [ 5.644967] bled: GPIO#18: netdev ath1. [ 5.650151] bled: GPIO#19: netdev ath0. 0.4 [1 init:init_nvram +6] init_nvram for model(93) set_basic_ifname_vars: WAN eth3 LAN eth1 eth2 eth0.1 [eth1 eth2 eth0.1 ath1 ath0 eth5 eth4] WIRED [eth1 eth2 eth0.1 eth5 eth4] 2G ath1 5G ath0 60G N/A USB usb AP_LAN N/A DW_WAN vlan2 DW_LAN 1 wan_ifnames: vlan10 usb [ 6.298958] ssdk_switch_device_num_init[842]:INFO:ess-switch dts node number: 2 [ 6.302632] ssdk_dt_get_switch_node[737]:INFO:ess-switch DT exist! [ 6.309569] ssdk_dt_parse_access_mode[638]:INFO:switch_access_mode: local bus [ 6.315738] ssdk_dt_parse_access_mode[651]:INFO:switchreg_base_addr: 0x3a000000 [ 6.322854] ssdk_dt_parse_access_mode[652]:INFO:switchreg_size: 0x1000000 [ 6.330141] ssdk_dt_parse_mac_mode[213]:INFO:mac mode = 0xb [ 6.336567] ssdk_dt_parse_mac_mode[222]:INFO:mac mode1 = 0xe [ 6.342119] ssdk_dt_parse_mac_mode[231]:INFO:mac mode2 = 0xd [ 6.347791] ssdk_dt_parse_uniphy[250]:INFO:ess-uniphy DT exist! [ 6.353523] ssdk_dt_parse_intf_mac[584]:INFO:dp1 MAC a8:5e:45:95:db:55 [ 6.359322] ssdk_dt_parse_intf_mac[584]:INFO:dp2 MAC a8:5e:45:95:db:55 [ 6.365835] ssdk_dt_parse_intf_mac[584]:INFO:dp3 MAC a8:5e:45:95:db:55 [ 6.372341] ssdk_dt_parse_intf_mac[584]:INFO:dp4 MAC a8:5e:45:95:db:55 [ 6.378852] ssdk_dt_parse_intf_mac[584]:INFO:dp5 MAC a8:5e:45:95:db:55 [ 6.385368] ssdk_dt_parse_intf_mac[584]:INFO:dp6 MAC a8:5e:45:95:db:55 [ 6.391869] ssdk_plat_init start [ 6.474482] ssdk_ppe_clock_init[463]:INFO:ppe and uniphy clock init successfully! [ 6.478155] HPPE initializing... [ 6.481194] malibu_phy_api_ops_init[2825]:INFO:qca probe malibu phy driver succeeded! [ 6.486938] aquantia_phy_api_ops_init[2169]:INFO:qca probe aquantia phy driver succeeded! [ 6.487323] sfp_phy_init[219]:INFO:sfp phy init for port 0x20! [ 6.491932] sfp_phy_probe[41]:INFO:sfp phy is probed! [ 6.491967] regi_init[3283]:INFO:Initializing HPPE!! hotplug net INTERFACE=miireg ACTION=add [ 6.702775] ssdk_ppe_reset_init[728]:INFO:ppe reset successfully! [ 6.708542] qca_hppe_tdm_hw_init[453]:INFO:tdm setup num=96 [ 8.364832] ssdk_switch_register[1617]:INFO:Chip version 0x1500 [ 8.367810] ssdk_switch_register[1642]:INFO:polling is selected [ 8.373707] regi_init[3287]:INFO:Initializing HPPE Done!! [ 8.378609] ssdk_dt_get_switch_node[737]:INFO:ess-switch DT exist! [ 8.385339] ssdk_dt_parse_access_mode[638]:INFO:switch_access_mode: mdio [ 8.391496] ssdk_dt_parse_mac_mode[213]:INFO:mac mode = 0x12 [ 8.397831] ssdk_dt_parse_mac_mode[222]:INFO:mac mode1 = 0xff [ 8.403478] ssdk_dt_parse_mac_mode[231]:INFO:mac mode2 = 0xf [ 8.409212] ssdk_dt_parse[800]:INFO:switch node is qca83xx! [ 8.414156] ssdk_plat_init start [ 8.480465] f1_phy_api_ops_init[1513]:INFO:qca probe f1 phy driver succeeded! [ 8.483440] qca803x_phy_api_ops_init[2029]:INFO:qca probe qca803x phy driver succeeded! [ 8.490949] regi_init[3273]:INFO:Initializing ISISC!! [ 8.497641] ssdk_switch_register[1617]:INFO:Chip version 0x1302 [ 8.503591] qca_link_polling_select[1284]:INFO:the interrupt number is:8d [ 8.509819] ssdk_switch_register[1652]:INFO:interrupt is selected [ 10.152772] regi_init[3277]:INFO:Initializing ISISC Done!! [ 10.154729] regi_init[3327]:INFO:qca-ssdk module init succeeded! [ 10.174819] EDMA ver 1 hw init [ 10.175062] EDMA HW Reset completed succesfully [ 10.176785] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7) [ 10.181182] RxDesc:1 (15-15) RxFill:1 (7-7) hotplug net INTERFACE=eth0 ACTION=add hotplug net INTERFACE=eth2 ACTION=add[ 10.200283] ********************************************************** [ 10.200786] * NSS Data Plane driver [ 10.208175] ********************************************************** hotplug net INTERFACE=eth1 ACTION=add hotplug net INTERFACE=eth4 ACTION=add hotplug net INTERFACE=eth3 ACTION=adhotplug net: add net eth3. hotplug net INTERFACE=eth3 ACTION=add: wait 1 seconds... hotplug net INTERFACE=eth5 ACTION=add [ 10.316576] nss_driver - fw of size 804672 bytes copied to load addr: 40000000, nss_id : 0 [ 10.317903] Supported Frequencies - [ 10.323792] 748.8 MHz 1.4976 GHz [ 10.329705] 1.6896 GHz [ 10.330748] hotplug net INTERFACE=qca-nss-dev0 ACTION=add hotplug net INTERFACE=qca-nss-dev1 ACTION=add hotplug net INTERFACE=qca-nss-dev4 ACTION=add hotplug net INTERFACE=qca-nss-dev3 ACTION=add hotplug net INTERFACE=qca-nss-dev5 ACTION=add hotplug net INTERFACE=qca-nss-dev6 ACTION=add hotplug net INTERFACE=qca-nss-dev7 ACTION=add hotplug net INTERFACE=qca-nss-dev8 ACTION=adhotplug net INTERFACE=qca-nss-dev2 ACTION=add [ 10.379822] node size 2 # items 4 [ 10.379842] memory: 40000000 1073741824 (avl 926916608) items 4 [ 10.382109] 7f2bc058: nss core 0 booted successfully [ 10.395160] nss_driver - fw of size 343360 bytes copied to load addr: 40800000, nss_id : 1 [ 10.395846] Supported Frequencies - [ 10.402347] 748.8 MHz 1.4976 GHz [ 10.408285] 1.6896 GHz [ 10.409328] hotplug net INTERFACE=qca-nss-dev9 ACTION=add hotplug net INTERFACE=qca-nss-dev10 ACTION=add hotplug net INTE[ 10.424136] node size 2 # items 4 [ 10.426703] memory: 40000000 1073741824 (avl 927219712) items 4 [ 10.426722] 7f2bea80: nss core 1 booted successfully [ 10.439881] QCA multicast snooping installed successfully RFACE=qca-nss-dev11 ACTION=add hotplug net INTERFACE=qca-nss-dev12 ACTION=add hotplug net INTERFACE=qca-nss-dev13 ACTION=add [ 10.456341] QCA Hy-Fi multicast installation successfully hotplug net INTERFACE=qca-nss-dev15 ACTION=add hotplug net INTE[ 10.465427] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded. RFACE=qca-nss-dev16 ACTION=add hotplug net INTERFACE=qca-nss-dev14 ACTION=add hotplug net INTERFACE=qca-nss-dev17 ACTION=add [ 10.556897] ECM init [ 10.556945] ECM database jhash random seed: 0x6c6917bb [ 10.578888] ECM init complete [ 10.665060] <NSS-CRYPTO>:module loaded Build_ID - 02/04/20, 13:21:12 SoC= [ 10.668186] crypto bench loaded - Build_ID - 02/04/20, 13:21:12 hotplug net INTERFACE=ipsecdummy ACTION=add [ 10.716150] sit: IPv6 over IPv4 tunneling driver hotplug net INTERFACE=sit0 ACTION=add hotplug net INTERFACE=ip6tnl0 ACTION=add config_switch(0x04df): link down all ports AQR PHY firmware 3.5 build 10.1 hotplug net INTERFACE=eth0.1 ACTION=add config_qca8075_8337_8035_8033_aqr107_LANWANPartition: LAN/P.WAN/S.WAN portmask 000006ff/00000100/00000000 Upstream eth3 (unit 0) config_switch(0x050f): ISP Profile/STB: manual/0 initialize_Vlan: LAN/P.WAN/S.WAN portmask 000006ff/00000100/00000000 Upstream eth3 (unit 0) __setup_vlan: vid 10 prio 0 mask 0x02000210 qca8075_8337_8035_8033_aqr107_vlan_set: vtype 1 upstream_if eth3 vid 10 prio 0 mbr 0x100 untag 0x0 hotplug net INTERFACE=vlan10 ACTION=add config_switch(0x0687): link up wan port(s) [ 11.083906] configuring additional NSS pbufs [ 11.103466] additional pbufs of size 7802880 got added to NSS [ 11.111642] mem_manager: module license 'unspecified' taints kernel. [ 11.111670] Disabling lock debugging due to kernel taint [ 11.117357] __mm_init_module [ 11.145853] qdf_dbg_mask value is invalid [ 11.145872] Using the default module debug levels instead [ 11.148835] qdf_print_ctrl_register: Allocated print control object 0 hotplug net INTERFACE=eth3 ACTION=add: wait 1 seconds... hotplug net INTERFACE=eth3 ACTION=add: wait 1 seconds... [ 12.573297] <SSR>: glink SUBSYS_BEFOER_POWERUP reinit done [ 12.573361] remoteproc0: q6v5-wcss is available [ 12.577666] remoteproc0: Note: remoteproc is still under development and considered experimental. [ 12.582449] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed. [ 12.603861] remoteproc0: powering up q6v5-wcss [ 12.609994] remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 796 [ 12.610211] Sanity check passed for the image [ 13.182884] eth0: PHY Link up speed: 1000 [ 13.465540] glink_core_link_up glink is up [ 13.465673] allocate_rx_intent rx intent id 1 allocated [ 13.465707] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled [ 13.465870] Subsystem error monitoring/handling services are up [ 13.465881] remoteproc0: remote processor q6v5-wcss is now up [ 13.465924] wlan: [689: I:ANY] ol_ath_ahb_ssr: SSR event 3 [ 13.491787] allocate_rx_intent rx intent id 2 allocated [ 13.497256] allocate_rx_intent rx intent id 3 allocated [ 13.502374] allocate_rx_intent rx intent id 4 allocated [ 13.507587] allocate_rx_intent rx intent id 5 allocated [ 13.512795] glink_xprt_open_event [ 13.519335] cnss: QMI WLFW service connected, state: 0x1 [ 13.521485] cnss: device_id : 0xffff mem mode : [0] [ 13.527419] Memory for FW, va: 0x4be40000, pa: 0x0x4be40000, size: 0x3d4000 [ 13.540605] cnss: BDF location : 0x4be00000 [ 13.540625] cnss: BDF IPQ8074/bdwlan.bin size 131072 [ 13.543855] cnss: BDF download response , result: 0, err: 0 [ 13.565149] cnss: per device BDF location : 0x4be20000 [ 13.565266] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000 [ 13.571571] cnss: BDF download response , result: 0, err: 0 [ 13.676773] wlan: [689: I:ANY] cnss_mode: Cold boot calibration [ 14.286286] Coldboot calibration wait started [ 14.287703] allocate_rx_intent rx intent id 6 allocated [ 14.289794] deallocate_rx_intent rx intent id 6 deallocated [ 14.295076] allocate_rx_intent rx intent id 6 allocated [ 14.300406] deallocate_rx_intent rx intent id 6 deallocated [ 14.305783] allocate_rx_intent rx intent id 6 allocated [ 14.311142] deallocate_rx_intent rx intent id 6 deallocated [ 14.316530] allocate_rx_intent rx intent id 6 allocated [ 14.322083] deallocate_rx_intent rx intent id 6 deallocated [ 14.327325] allocate_rx_intent rx intent id 6 allocated [ 14.332665] deallocate_rx_intent rx intent id 6 deallocated [ 14.338124] deallocate_rx_intent rx intent id 6 deallocated [ 14.343715] deallocate_rx_intent rx intent id 6 deallocated [ 14.349250] deallocate_rx_intent rx intent id 6 deallocated [ 14.354824] deallocate_rx_intent rx intent id 6 deallocated [ 14.360359] deallocate_rx_intent rx intent id 6 deallocated [ 14.686412] Coldboot calibration wait ended [ 14.687041] wlan: [689: I:ANY] Coldboot calib successful: radio_id 0x65535 [ 14.687053] cnss: QMI WLFW service disconnected, state: 0x9 [ 14.697097] ath_ol_pci: (Atheros/multi-bss) [ 14.704552] wlan: [747: I:ANY] ol_ath_ahb_ssr: SSR event 0 [ 14.731855] remoteproc0: stopped remote processor q6v5-wcss [ 14.732051] glink_core_link_down glink is down [ 14.736656] <SSR>: glink SUBSYS_AFTER_SHUTDOWN cleanup done [ 14.772786] glink_xprt_close_event [ 14.892870] qdf_print_ctrl_cleanup: Print control object 0 cleaned up [ 14.922888] __mm_exit_module [ 14.955877] __mm_init_module [ 14.958843] qdf_dbg_mask value is invalid [ 14.958863] Using the default module debug levels instead [ 14.961900] qdf_print_ctrl_register: Allocated print control object 0 [ 15.962793] <SSR>: glink SUBSYS_BEFOER_POWERUP reinit done [ 15.962858] remoteproc0: q6v5-wcss is available [ 15.967194] remoteproc0: Note: remoteproc is still under development and considered experimental. [ 15.971965] remoteproc0: THE BINARY FORMAT IS NOT YET FINALIZED, and backward compatibility isn't yet guaranteed. [ 15.986878] remoteproc0: powering up q6v5-wcss [ 15.996985] remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 796 [ 15.997215] Sanity check passed for the image [ 16.403463] glink_core_link_up glink is up [ 16.403594] glink_xprt_open_event [ 16.403799] Subsystem error monitoring/handling services are up [ 16.403815] remoteproc0: remote processor q6v5-wcss is now up [ 16.403911] wlan: [758: I:ANY] ol_ath_ahb_ssr: SSR event 3 [ 16.421517] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled [ 16.540624] cnss: QMI WLFW service connected, state: 0x9 [ 16.540647] cnss: device_id : 0xffff mem mode : [0] [ 16.545266] Memory for FW, va: 0x4be40000, pa: 0x0x4be40000, size: 0x3d4000 [ 16.555731] cnss: BDF location : 0x4be00000 [ 16.556534] cnss: BDF IPQ8074/bdwlan.bin size 131072 [ 16.561009] cnss: BDF download response , result: 0, err: 0 [ 16.578869] cnss: per device BDF location : 0x4be20000 [ 16.578982] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000 [ 16.585280] cnss: BDF download response , result: 0, err: 0 [ 16.609179] wlan: [758: I:ANY] cnss_mode: Mission mode [ 16.616575] wlan: [758: I:ANY] qca_napi_create: napi instance 0 created on pipe 4 [ 16.616689] wlan: [758: I:ANY] __ol_ath_attach(): Allocated soc b4f80500 [ 16.623107] btcoex_support 0 wlan_prio_gpio 0 [ 16.629910] wlan: [758: I:ANY] nss-wifili:#1 register wifili function for soc [ 16.634103] wlan: [758: I:ANY] nss register id -1 nss config 1 Target Type 14 [ 16.641256] wlan: [758: I:ANY] __ol_ath_attach: dev name soc0 [ 16.648603] wlan: [758: I:ANY] Skipping BMI [ 16.654332] wlan: [758: I:ANY] ol_ath_soc_attach() WMI attached. wmi_handle b8fa7400 [ 16.658259] wlan: [758: I:ANY] htc_wmi_init() HT Create . b6abd000 [ 16.666220] wlan: [758: I:ANY] htc_wmi_init() Skipping BMI Done. [ 16.672269] wlan: [758: I:ANY] htc_wmi_init 5307 host_enable 0 nss_nwifi_offload 0 [ 16.678481] wlan: [758: I:TIF] init_deinit_set_init_cmd_dev_params: 785: AC Minfree buf allocation through module param (umac.ko) [ 16.687253] wlan: [758: I:TIF] init_deinit_set_init_cmd_dev_params: 786: OL_ACBKMinfree : 0 [ 16.697652] wlan: [758: I:TIF] init_deinit_set_init_cmd_dev_params: 787: OL_ACBEMinfree : 0 [ 16.706174] wlan: [758: I:TIF] init_deinit_set_init_cmd_dev_params: 788: OL_ACVIMinfree : 0 [ 16.714576] wlan: [758: I:TIF] init_deinit_set_init_cmd_dev_params: 789: OL_ACVOMinfree : 0 [ 16.723088] wlan: [758: I:TIF] init_deinit_set_init_cmd_dev_params: 809: num_peers 1058, num_vdevs 17, num_tids 8540 [ 16.723102] send_filled_buffers_to_user: Send Failed -3 drop_count = 1 [ 16.744787] wlan: [758: I:ANY] CDP soc attach success [ 16.748245] wlan: [758: I:ANY] Soc attach success NSS config 3 [ 16.753405] wlan: [758: I:ANY] htc_set_async_ep: htc_handle b6abd000, ep 2, value 1 [ 16.759115] wlan: [758: I:ANY] htc_set_async_ep: htc_handle b6abd000, ep 3, value 1 [ 16.767230] wlan: [739: I:ANY] SVC ready arrival: 16.764443 [ 16.774334] wlan: [739: I:ANY] SVC ready execution: 16.764460 [ 16.780231] wlan: [739: I:ANY] SVC ready time to schedule: 0.000017 [ 16.785886] wlan: [739: I:TIF] init_deinit_populate_phy_reg_cap: 334: FW wireless modes 0x7f9001 [ 16.792395] wlan: [739: I:TIF] init_deinit_service_ready_event_handler: 118: TT support 1, Wide BW Scan 1, SW cal 1 [ 16.801176] wlan: [739: I:ANY] num_rf_chain:0x00000008 [ 16.811658] wlan: [739: I:ANY] ht_cap_info:0x0000081f [ 16.816951] wlan: [739: I:ANY] vht_cap_info:0x738fe9fa [ 16.821895] wlan: [739: I:ANY] vht_supp_mcs:0x0000fffa [ 16.827456] wlan: [739: I:TIF] init_deinit_service_ready_event_handler: 154: WMI mgmt service enabled [ 16.832410] wlan: [739: I:TIF] init_deinit_service_ready_event_handler: 173: Wait for EXT message [ 16.841706] wlan: [739: I:ANY] SVC ext ready arrival: 16.764467 [ 16.850548] wlan: [739: I:ANY] SVC ext ready execution: 16.838937 [ 16.856639] wlan: [739: I:ANY] SVC ext ready time to schedule:0.074470 [ 16.862610] wlan: [739: I:ANY] Num chain mask tables: 3 [ 16.869122] wlan: [739: I:ANY] Dumping chain mask combo data [ 16.874332] wlan: [739: I:ANY] table_id : 0 Num valid chainmasks: 25 [ 16.880232] wlan: [739: I:ANY] table_id : 1 Num valid chainmasks: 7 [ 16.886572] wlan: [739: I:ANY] table_id : 2 Num valid chainmasks: 8 [ 16.892556] wlan: [739: I:ANY] chain mask combo end [ 16.898809] wlan: [739: I:TIF] init_deinit_populate_hw_mode_capability: 223: num_hw_modes 2 [ 16.903679] wlan: [739: I:TIF] init_deinit_populate_mac_phy_capability: 164: hw_mode_id 1 phy_bit_map 0x3 [ 16.912012] wlan: [739: I:TIF] init_deinit_populate_mac_phy_capability: 187: total_mac_phy_cnt 2 [ 16.921735] wlan: [739: I:TIF] init_deinit_populate_hw_mode_capability: 246: num radios is 2 [ 16.930588] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1072: HE_CAP Info = 1a000109 [ 16.939009] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1073: Num HW modes = 2 [ 16.948123] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1074: Num PHY = 2 [ 16.957077] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1075: HW mode and MAC PHY CAP [ 16.965140] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1082: idx = 0 hw_mode_id = 1 pdev_id = 0 phy_id = 0 [ 16.974524] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1084: 11G support = 0 [ 16.985972] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1085: 11A support = 1 [ 16.994825] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1086: 11N support = 1 [ 17.003765] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1087: 11AC support = 1 [ 17.012702] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1088: 11AX support = 1 [ 17.021648] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1090: Supported bands = 2 [ 17.030590] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1092: Ampdu density = 0 [ 17.039877] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1094: Max BW supported 2G = 1 [ 17.048732] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1096: 2G - HT cap info = 381f [ 17.058368] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1098: 2G - VHT cap info = 738fe992 [ 17.067917] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1100: 2G - Supported VHT MCS =fffa [ 17.077812] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1102: 2G - HE cap = b6abe2e8 [ 17.087795] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1104: 2G - HE supp MCS = fffa [ 17.097430] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1106: 2G - TX chain mask = 3 [ 17.106987] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1108: 2G - RX chain mask = 3 [ 17.116529] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1113: HE_CAP_PHY_INFO_2G[0] = 0 HE_CAP_PHY_INFO_2G[1]=0 HE_CAP_PHY_INFO_2G [2]=0 [ 17.125652] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1116: 2G - HE_PPET5G_NUMSS_M1 =0 HE_PPET5G_RU_MASK=0 [ 17.139881] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1118: 5G - Max BW supported = 4 [ 17.151076] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1120: 5G - HT cap info = 381f [ 17.160799] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1122: 5G - VHT cap info = 738fe9fa [ 17.170520] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1124: 5G - Supported VHT MCS aaaa [ 17.180418] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1126: 5G - HE cap = b6abe30c [ 17.190486] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1128: 5G - HE supp MCS = ffaaaaaa [ 17.199945] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1130: 5G - tx chain mask = ff [ 17.209671] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1132: 5G - RX chain mask = 255 [ 17.219220] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1137: HE_CAP_PHY_INFO_5G[0] = 800c601c HE_CAP_PHY_INFO_5G[1]= 4801f02 HE_CAP_PHY_INFO_5G [2]=0 [ 17.228691] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1140: 5G - HE_PPET5G_NUMSS_M1 = 7 HE_PPET5G_RU_MASK=f [ 17.243795] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1142: chain mask tableid= 0 [ 17.255417] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1082: idx = 1 hw_mode_id = 1 pdev_id = 1 phy_id = 1 [ 17.264539] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1084: 11G support = 1 [ 17.275901] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1085: 11A support = 0 [ 17.284757] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1086: 11N support = 1 [ 17.293697] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1087: 11AC support = 1 [ 17.302633] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1088: 11AX support = 1 [ 17.311579] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1090: Supported bands = 1 [ 17.320519] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1092: Ampdu density = 0 [ 17.329807] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1094: Max BW supported 2G = 1 [ 17.338663] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1096: 2G - HT cap info = 381f [ 17.348298] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1098: 2G - VHT cap info = 738b6992 [ 17.357848] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1100: 2G - Supported VHT MCS =ffaa [ 17.367743] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1102: 2G - HE cap = b6abe3b8 [ 17.377738] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1104: 2G - HE supp MCS = ffaa [ 17.387363] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1106: 2G - TX chain mask = f [ 17.396909] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1108: 2G - RX chain mask = 15 [ 17.406459] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1113: HE_CAP_PHY_INFO_2G[0] = 800c6002 HE_CAP_PHY_INFO_2G[1]=4800302 HE_CAP_PHY_INFO_2G [2]=0 [ 17.415931] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1116: 2G - HE_PPET5G_NUMSS_M1 =3 HE_PPET5G_RU_MASK=3 [ 17.430940] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1118: 5G - Max BW supported = 1 [ 17.442222] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1120: 5G - HT cap info = 381f [ 17.451943] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1122: 5G - VHT cap info = 738b69b2 [ 17.461667] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1124: 5G - Supported VHT MCS fffa [ 17.471562] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1126: 5G - HE cap = b6abe3dc [ 17.481544] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1128: 5G - HE supp MCS = fffefffa [ 17.491006] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1130: 5G - tx chain mask = 3 [ 17.500814] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1132: 5G - RX chain mask = 3 [ 17.510025] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1137: HE_CAP_PHY_INFO_5G[0] = 0 HE_CAP_PHY_INFO_5G[1]= 0 HE_CAP_PHY_INFO_5G [2]=0 [ 17.519402] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1140: 5G - HE_PPET5G_NUMSS_M1 = 0 HE_PPET5G_RU_MASK=0 [ 17.533633] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1142: chain mask tableid= 1 [ 17.545174] wlan: [739: I:TIF] init_deinit_print_service_ready_ex_params: 1145: Preferred HW Mode = 1 Num Radios = 2 [ 17.554294] wlan: [739: I:TIF] init_deinit_populate_phy_reg_cap: 342: num_phy_reg_cap 2 [ 17.564966] wlan: [739: I:TIF] init_deinit_add_11ax_modes: 1270: Adding 11ax regulatory modes, [ 17.572684] wlan: [739: I:TIF] init_deinit_add_11ax_modes: 1273: phy_id = 0 wireless modes = f97f9001 [ 17.581369] wlan: [739: I:TIF] init_deinit_add_11ax_modes: 1270: Adding 11ax regulatory modes, [ 17.590657] wlan: [739: I:TIF] init_deinit_add_11ax_modes: 1273: phy_id = 1 wireless modes = 680680c [ 17.599256] wlan: [739: I:ANY] Dumping chain mask combo data for table : 0 [ 17.608537] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000001 [ 17.615308] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000002 [ 17.622860] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000004 [ 17.630407] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000008 [ 17.637963] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000010 [ 17.645525] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000020 [ 17.653069] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000040 [ 17.660616] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000080 [ 17.668173] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000003 [ 17.675724] wlan: [739: I:ANY] supported_flags: 0xf0000007 chainmasks: 0x00000009 [ 17.683276] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000030 [ 17.690825] wlan: [739: I:ANY] supported_flags: 0xf0000007 chainmasks: 0x00000090 [ 17.698381] wlan: [739: I:ANY] supported_flags: 0x70000018 chainmasks: 0x00000090 [ 17.705933] wlan: [739: I:ANY] supported_flags: 0x70000018 chainmasks: 0x00000050 [ 17.713484] wlan: [739: I:ANY] supported_flags: 0x70000018 chainmasks: 0x000000a0 [ 17.721033] wlan: [739: I:ANY] supported_flags: 0x70000018 chainmasks: 0x00000011 [ 17.728588] wlan: [739: I:ANY] supported_flags: 0x70000018 chainmasks: 0x00000022 [ 17.736141] wlan: [739: I:ANY] supported_flags: 0x70000018 chainmasks: 0x00000044 [ 17.743693] wlan: [739: I:ANY] supported_flags: 0x70000018 chainmasks: 0x00000088 [ 17.751240] wlan: [739: I:ANY] supported_flags: 0xf0000007 chainmasks: 0x00000007 [ 17.758796] wlan: [739: I:ANY] supported_flags: 0xf0000007 chainmasks: 0x00000070 [ 17.766349] wlan: [739: I:ANY] supported_flags: 0x7000001f chainmasks: 0x0000000f [ 17.773908] wlan: [739: I:ANY] supported_flags: 0x7000001f chainmasks: 0x000000f0 [ 17.781449] wlan: [739: I:ANY] supported_flags: 0xf000001f chainmasks: 0x00000077 [ 17.789007] wlan: [739: I:ANY] supported_flags: 0xf000001f chainmasks: 0x000000ff [ 17.796557] wlan: [739: I:ANY] Dumping chain mask combo data for table : 1 [ 17.804110] wlan: [739: I:ANY] supported_flags: 0x68000003 chainmasks: 0x00000001 [ 17.810962] wlan: [739: I:ANY] supported_flags: 0x68000003 chainmasks: 0x00000002 [ 17.818519] wlan: [739: I:ANY] supported_flags: 0x68000003 chainmasks: 0x00000004 [ 17.826071] wlan: [739: I:ANY] supported_flags: 0x68000003 chainmasks: 0x00000008 [ 17.833624] wlan: [739: I:ANY] supported_flags: 0x68000003 chainmasks: 0x00000003 [ 17.841171] wlan: [739: I:ANY] supported_flags: 0x68000003 chainmasks: 0x00000007 [ 17.848728] wlan: [739: I:ANY] supported_flags: 0x68000003 chainmasks: 0x0000000f [ 17.856279] wlan: [739: I:ANY] Dumping chain mask combo data for table : 2 [ 17.863831] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000001 [ 17.870685] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000002 [ 17.878241] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000004 [ 17.885794] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000008 [ 17.893345] wlan: [739: I:ANY] supported_flags: 0x70000007 chainmasks: 0x00000003 [ 17.900902] wlan: [739: I:ANY] supported_flags: 0xf0000007 chainmasks: 0x00000009 [ 17.908451] wlan: [739: I:ANY] supported_flags: 0xf0000007 chainmasks: 0x00000007 [ 17.916002] wlan: [739: I:ANY] supported_flags: 0xf0000007 chainmasks: 0x0000000f [ 17.923554] wlan: [739: I:TIF] init_deinit_populate_dbr_ring_cap: 264: Num DMA Capabilities = 2 [ 17.931110] wlan: [739: I:TIF] init_deinit_derive_band_to_mac_param: 423: 5G radio -pdev_id = 0 start_freq = 4910 end_freq =6100 [ 17.939710] wlan: [739: I:TIF] init_deinit_derive_band_to_mac_param: 406: 2G radio - pdev_id = 1 start_freq = 2312 end_freq= 2732 [ 17.951625] wlan: [739: I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 326: dfs_offload 1 [ 17.963172] wlan: [739: I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 312: Do not allocate DFS object for 2G, pdev_id = 1 [ 17.988659] wlan: [739: I:TIF] init_deinit_update_pdev_tgt_info: 969: CDP PDEV ATTACH success [ 18.001870] wlan: [739: I:TIF] init_deinit_update_pdev_tgt_info: 969: CDP PDEV ATTACH success [ 18.102197] wlan: [739: I:TIF] init_deinit_prepare_send_init_cmd: 473: FW version 0x30f0e14 [ 18.102226] wlan: [739: I:TIF] init_deinit_prepare_send_init_cmd: 477: 0x283e960e [ 18.109706] wlan: [739: I:ANY] copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0 [ 18.346844] wlan: [0: I:TIF] tgt_reg_chan_list_update_handler: 101: enter [ 18.353902] wlan: [0: I:TIF] tgt_reg_chan_list_update_handler: 101: enter [ 18.354149] wlan: [739: I:ANY] WMI ready arrival: 18.351349 [ 18.359657] wlan: [739: I:ANY] WMI ready execution: 18.351364 [ 18.365393] wlan: [739: I:ANY] WMI ready time to schedule: 0.000015 [ 18.371033] wlan: [739: I:ANY] dp_peer_map_attach_wifi3 max_peers 1111, max_ast_index: 4112 [ 18.377580] wlan: [739: I:ANY] ast hash_elems: 16384, max_ast_idx: 4112 [ 18.385713] wlan: [739: I:ANY] ready_extract_init_status_tlv:0 [ 18.392226] wlan: [758: I:ANY] ol_ath_connect_htc() WMI is ready [ 18.425574] wlan: [758: I:dfs] WLAN_DEBUG_DFS_ALWAYS : wifi_dfs_psoc_enable: 408: dfs_offload 1 [ 18.425612] wlan: [758: I:ANY] ol_ath_soc_attach() connect HTC. [ 18.433310] wlan: [758: I:ANY] bypasswmi : 0 [ 18.439533] wlan: [758: I:ANY] 7ol_ath_lowi_wmi_event_attach: called [ 18.443782] wlan: [758: I:ANY] 7ol_ath_phyerr_attach: called [ 18.450882] wlan: [758: I:ANY] 7ol_ath_rtt_meas_report_attach: called [ 18.455839] wlan: [758: I:ANY] ol_ath_soc_attach() UMAC attach . [ 18.462286] wlan: [758: I:ANY] ath_lowi_if_netlink_init LOWI Netlink successfully created [ 18.468655] wlan: [758: I:ANY] __ol_ath_attach: pdev_netdev name wifi0 [ 18.476607] wlan: [758: I:ANY] Skip txrx_pdev_attach_target [ 18.483001] wlan: [758: I:ANY] BURSTING enabled by default [ 18.488558] wlan: [758: I:ANY] ol_ath_pdev_attach interface_id 0 [ 18.494089] wlan: [758: I:ANY] phy id = 0 Modes supported [ 18.500244] wlan: [758: I:ANY] 11b = 0 11g = 0 11a = 1 11n = 1 11ac = 1 11ax = 1 [ 18.505499] wlan: [758: I:ANY] Reg cap - phy_id = 0 supp_bnd = 2, modes = f97f9001, lo_2g = 0, hi_2g = 0 lo_g5 = 4910, hi_5g = 6100 [ 18.513051] wlan: [758: I:ANY] ol_ath_update_wireless_modes: wireless_modes = f97f9001 before update [ 18.525047] wlan: [758: I:ANY] ol_ath_update_wireless_modes: Wireless_modes = f97f9001 after update [ 18.534167] wlan: [758: I:ANY] ol_ath_update_ext_caps: 11ax 5G supported case [ 18.542954] wlan: [758: I:ANY] EXT NSS Supported [ 18.550513] wlan: [758: I:ANY] OL Resmgr Init-ed [ 18.555035] wlan: [758: I:ANY] acfg_attach: 3187: Netlink socket created:b6395800 [ 18.559590] wlan: [758: I:ANY] rate power table override is only supported for AR98XX [ 18.566952] wlan: [758: I:ANY] ol_ath_stats_attach: periodic_chan_stats: 1 [ 18.578340] wlan: [0: I:ANY] ol_ath_pdev_attach: Set global_ic[1] ..ptr:7fc702b4 [ 18.581341] wlan: [0: I:ANY] pdev(b8fa0004) Enabling DBDC Repeater 1 [ 18.589166] wlan: [0: E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed [ 18.595527] wlan: [0: I:ANY] pdev(b8fa0004) is_primary 1 [ 18.603610] wlan: [758: I:ANY] Pdev = 0 Number of peers = 529 [ 18.612597] wlan: [758: I:ANY] osif_wrap_attach:485 osif wrap attached [ 18.614726] wlan: [758: I:ANY] osif_wrap_devt_init:446 osif wrap dev table init done [ 18.621135] wlan: [758: I:ANY] Wrap Attached: Wrap_com =b8fa7800 ic->ic_wrap_com=b8fa7800 &wrap_com->wc_devt=b8fa7800 [ 18.629061] wlan: [758: I:ANY] __ol_ath_attach: needed_headroom reservation 60 [ 18.639588] wlan: [758: I:ANY] Enabled Fraglist bit for the radio wifi0 features 41 [ 18.647222] wlan: [758: I:ANY] ol_ath_thermal_mitigation_attach: -- [ 18.654671] wlan: [758: I:ANY] __ol_ath_attach: pdev_netdev name wifi1 [ 18.660573] wlan: [758: I:ANY] Skip txrx_pdev_attach_target [ 18.667146] wlan: [758: I:ANY] BURSTING enabled by default [ 18.672680] wlan: [758: I:ANY] ol_ath_pdev_attach interface_id 1 [ 18.678300] wlan: [758: I:ANY] phy id = 1 Modes supported [ 18.684381] wlan: [758: I:ANY] 11b = 1 11g = 1 11a = 0 11n = 1 11ac = 1 11ax = 1 [ 18.689617] wlan: [758: I:ANY] Reg cap - phy_id = 1 supp_bnd = 1, modes = 680680c, lo_2g = 2312, hi_2g = 2732 lo_g5 = 0, hi_5g = 0 [ 18.697183] wlan: [758: I:ANY] ol_ath_update_wireless_modes: wireless_modes = 680680c before update [ 18.709017] wlan: [758: I:ANY] ol_ath_update_wireless_modes: Wireless_modes = 680680c after update [ 18.717832] wlan: [758: I:ANY] ol_ath_update_ext_caps: 11ax 2G supported case [ 18.726892] wlan: [758: I:ANY] EXT NSS Supported [ 18.734165] wlan: [758: I:ANY] OL Resmgr Init-ed [ 18.738900] wlan: [758: I:ANY] acfg_attach: Offload using existing sock b6395800 [ 18.743446] wlan: [758: I:ANY] rate power table override is only supported for AR98XX [ 18.750814] wlan: [758: I:ANY] ol_ath_stats_attach: periodic_chan_stats: 1 [ 18.758791] wlan: [0: I:ANY] ol_ath_pdev_attach: Set global_ic[2] ..ptr:7fc702b4 [ 18.765288] wlan: [0: I:ANY] pdev(b8fa0884) Enabling DBDC Repeater 1 [ 18.772922] wlan: [0: E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed [ 18.779239] wlan: [0: I:ANY] pdev(b8fa0884) is_primary 0 [ 18.787377] wlan: [758: I:ANY] Pdev = 1 Number of peers = 529 [ 18.793818] wlan: [758: I:ANY] osif_wrap_attach:485 osif wrap attached [ 18.798498] wlan: [758: I:ANY] osif_wrap_devt_init:446 osif wrap dev table init done [ 18.804923] wlan: [758: I:ANY] Wrap Attached: Wrap_com =a4c2a800 ic->ic_wrap_com=a4c2a800 &wrap_com->wc_devt=a4c2a800 [ 18.812818] wlan: [758: I:ANY] __ol_ath_attach: needed_headroom reservation 60 [ 18.823316] wlan: [758: I:ANY] Enabled Fraglist bit for the radio wifi1 features 41 [ 18.831190] wlan: [758: I:ANY] ol_ath_thermal_mitigation_attach: -- [ 18.838921] wlan: [758: I:ANY] ol_ath_ahb_probe num_radios=2, wifi_radios[0].sc = b4d60500_radio_type = 2 [ 18.844586] wlan: [758: I:ANY] ol_ath_ahb_probe num_radios=2, wifi_radios[1].sc = b4d40500_radio_type = 2 [ 18.854311] wlan: [758: I:ANY] ath_sysfs_diag_init: diag_fsattr [ 18.864090] ath_ol_pci: (Atheros/multi-bss) hotplug net INTERFACE=wifi0 ACTION=add hotplug net INTERFACE=wi[ 18.878021] wlan: [832: I:ANY] __sa_init_module fi1 ACTION=add hotplug net INTERFACE=soc0 ACTION=add [ 20.901334] wlan: [0: I:TIF] tgt_reg_chan_list_update_handler: 101: enter [ 20.907775] wlan: [0: I:TIF] tgt_reg_chan_list_update_handler: 101: enter [ 20.915851] wlan: [840: I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 574: freq=58 [ 20.915878] wlan: [840: I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 574: freq=106 [ 20.923019] wlan: [840: I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 574: freq=122 [ 20.931161] wlan: [840: I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 574: freq=138 [ 20.940383] wlan: [840: I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 574: freq=58 [ 20.947660] wlan: [840: I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 574: freq=106 [ 20.955905] wlan: [840: I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 574: freq=122 [ 20.964066] wlan: [840: I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 574: freq=138 init_wl(0x09be): init_wl:create wi node create_vap(0x0785): create a wifi node ath1 from wifi1 [ 21.028017] wlan_vap_create : enter. devhandle=0xb4d40500, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 21.028060] wlan: [843: I:ANY] ol_ath_vap_create: vdev id 0 [ 21.035645] wlan: [843: I:ANY] nss-wifi:#0 VAP# vap ad580000 nss_if 32 [ 21.041484] wlan: [843: I:ANY] ol_ath_vap_set_param : Setting the following vdev params vap->iv_he_su_bfee: 0, vap->iv_he_su_bfer: 1 vap->iv_he_mu_bfee: 0, vap->iv_he_mu_bfer: 1 vap->iv_h [ 21.048185] wlan: [843: I:ANY] ol_ath_vap_set_param : WMI: he_bf_cap = 0x1a [ 21.070480] wlan: [843: I:ANY] dp_lag_pdev_set_ap_vdev pdev(b8fa0884) ap_vdev b5764a00 [ 21.077202] wlan: [843: I:ANY] nss-wifi:#0 VAP# vdev b4ffa000 vap ad580000 osif b5bb7500 nss_if 32 [ 21.085179] wlan: [843: I:ANY] update nss wifiol ctx in osdev [ 21.094202] wlan: [843: I:ANY] NSS wifi offload VAP create IF 32 nss_id -1 [ 21.100100] wlan: [843: I:ANY] ****NSS radio_if 31**** [ 21.106931] wlan: [0: I:ANY] VDEV configuration success: 0 [ 21.112086] wlan: [843: I:ANY] vap create b5bb7500 : if_num 32 [ 21.117656] wlan_vap_create : exit. devhandle=0xb4d40500, vap=0xad580000, opmode=IEEE80211_M_HOSTAP, flags=0x1. [ 21.118059] wlan: [0: I:ANY] Get MPSTA: vdev is NULL [ 21.133452] wlan: [843: I:ANY] TX Checksum Bit: 1| SG Bit: 1| TSO Bit: 1 | LRO Bit: 0 [ 21.138643] wlan: [843: I:ANY] WLAN-NSS: VAP NSS ops initialized [ 21.146413] wlan: [843: I:ANY] ol_ath_update_phymode_caps: Error Mode 0 not 2G or 5G [ 21.154771] wlan: [843: I:ANY] VAP device ath1 created osifp: (b5bb7500) os_if: (ad580000) [ 21.160339] wlan: [843: I:ANY] 3VAP device ath1 created! hotplug net INTERFACE=ath1 ACTION=add create_vap(0x0785): create a wifi node ath0 from wifi0 [ 22.172154] wlan_vap_create : enter. devhandle=0xb4d60500, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 22.172990] wlan: [854: I:ANY] ol_ath_vap_create: vdev id 1 [ 22.181516] wlan: [854: I:ANY] nss-wifi:#0 VAP# vap a4d00000 nss_if 33 [ 22.187425] wlan: [854: I:ANY] ol_ath_vap_set_param : Setting the following vdev params vap->iv_he_su_bfee: 0, vap->iv_he_su_bfer: 1 vap->iv_he_mu_bfee: 0, vap->iv_he_mu_bfer: 1 vap->iv_h [ 22.194086] wlan: [854: I:ANY] ol_ath_vap_set_param : WMI: he_bf_cap = 0x1a [ 22.216488] wlan: [854: I:ANY] dp_lag_pdev_set_ap_vdev pdev(b8fa0004) ap_vdev a4c2aa00 [ 22.223081] wlan: [854: I:ANY] nss-wifi:#0 VAP# vdev bbd40800 vap a4d00000 osif b7173500 nss_if 33 [ 22.231080] wlan: [854: I:ANY] update nss wifiol ctx in osdev [ 22.240493] wlan: [854: I:ANY] NSS wifi offload VAP create IF 33 nss_id -1 [ 22.245974] wlan: [854: I:ANY] ****NSS radio_if 30**** [ 22.252880] wlan: [0: I:ANY] VDEV configuration success: 0 [ 22.257966] wlan: [854: I:ANY] vap create b7173500 : if_num 33 [ 22.263571] wlan_vap_create : exit. devhandle=0xb4d60500, vap=0xa4d00000, opmode=IEEE80211_M_HOSTAP, flags=0x1. [ 22.269261] wlan: [0: I:ANY] Get MPSTA: vdev is NULL [ 22.279345] wlan: [854: I:ANY] TX Checksum Bit: 1| SG Bit: 1| TSO Bit: 1 | LRO Bit: 0 [ 22.284551] wlan: [854: I:ANY] WLAN-NSS: VAP NSS ops initialized [ 22.292321] wlan: [854: I:ANY] ol_ath_update_phymode_caps: Error Mode 0 not 2G or 5G [ 22.299040] wlan: [854: I:ANY] VAP device ath0 created osifp: (b7173500) os_if: (a4d00000) [ 22.306298] wlan: [854: I:ANY] 3VAP device ath0 created! hotplug net INTERFACE=ath0 ACTION=add set_nss_power_save_mode: NSS min/max freq: 187200000/1497600000 1: check_action 0: 1(init) *** ubifs: jffs2 0, 5, 144371712 1: check_action 0: 1(init) 1: set_action 7 1: set_action 0 Insert USB modules early. [ 25.871902] msm-usb-ssphy-qmp 78000.ssphy: QMP PHY initialization timeout [ 25.871927] msm-usb-ssphy-qmp 78000.ssphy: USB3_PHY_PCS_STATUS:68686868 [ 26.087556] msm-usb-ssphy-qmp 58000.ssphy: QMP PHY initialization timeout [ 26.087577] msm-usb-ssphy-qmp 58000.ssphy: USB3_PHY_PCS_STATUS:68686868 start_logger: update_lan_state(lan_, 0, 0) hotplug net INTERFACE=br0 ACTION=add _ifconfig: name=eth1 flags=1243 IFUP addr= netmask= _ifconfig: name=eth2 flags=1243 IFUP addr= netmask= _ifconfig: name=eth0.1 flags=1243 IFUP addr= netmask= _ifconfig: name=eth5 flags=1243 IFUP addr= netmask= _ifconfig: name=eth4 flags=1243 IFUP addr= netmask= start_lan: setting MAC address of bridge br0 as A8:5E:45:95:DB:55 _ifconfig: name=br0 flags=1243 IFUP addr=192.168.50.1 netmask=255.255.255.0 _ifconfig: name=ath1 flags=0000 addr= netmask= _ifconfig: name=ath0 flags=0000 addr= netmask= gen qca config gen qca config [ 26.519439] wlan: [982: I:ANY] set TXBF_SND_PERIOD: value 100 wmi_status 0 [ 26.524973] wlan: [0: I:ANY] Disconnect_timeout value entered:10 [ 26.526541] wlan: [0: I:ANY] reconfiguration_timeout value entered:60 [ 26.541460] wlan: [994: I:ANY] EXT NSS Supported [ 26.552835] [MLME] vap-0(ath1):wlan_mlme_stop_bss: disassoc/deauth all stations. iv_node_count: 1, peer_cnt: 1 [ 26.583215] wlan: [1003: I:ANY] set TXBF_SND_PERIOD: value 100 wmi_status 0 [ 26.588790] wlan: [0: I:ANY] Disconnect_timeout value entered:10 [ 26.590368] wlan: [0: I:ANY] reconfiguration_timeout value entered:60 [ 26.606789] wlan: [1016: I:ANY] EXT NSS Supported [ 26.609694] [MLME] vap-1(ath0):wlan_mlme_stop_bss: disassoc/deauth all stations. iv_node_count: 1, peer_cnt: 1 _ifconfig: name=lo flags=1043 IFUP addr=127.0.0.1 netmask=255.0.0.0 route_manip: cmd=ADD name=lo addr=127.0.0.0 netmask=255.0.0.0 gateway=0.0.0.0 metric=0 update_lan_state(lan_, 2, 0) nat_rule: stop_nat_rules 1. start_lan 2138 # wanduck: Got LAN(-1) information: wanduck: delay 1 seconds before the first detect... [1 init:start_dnsmasq +28] begin [1 init:stop_dnsmasq +28] begin [1 init:stop_dnsmasq +28] end [1 init:start_dnsmasq +28] end start_lan_port(0) 1 decomp: fname=/var/lib/misc/rstats-speed.gz decomp: gzip -dc /var/lib/misc/rstats-speed.gz > /var/tmp/rstats-uncomp != 0 load: speed_count = 0 load: read source= save_path= load_history: fname=/var/lib/misc/rstats-history.gz decomp: fname=/var/lib/misc/rstats-history.gz ### onboarding model=RT-AX89X, reboot_time=80, connection_timeout=120, traffic_timeout=60 TZ watchdog decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0 decomp: fname=/var/lib/misc/rstats-history.gz msgget ok decomp: gzip -dc /var/lib/misc/rstats-history.gz > /var/tmp/rstats-uncomp != 0 load_history: load failed disk_monitor: starting... disk_monitor: day=5, week=6, time=18:5. disk_monitor: decide if scan the target... disk_monitor: 0: wait_second=18000... disk_monitor: 1: wait_second=18000... disk_monitor: wait_second=18000... disk_monitor: Pause... [bwdpi check] starting... rc: ==> binding interface(eth1,eth2,eth0.1,ath1,ath0,eth5,eth4) for lldpd RAST 28: ROAMAST Start... wanduck: delay 2 seconds before the first detect... wanduck: delay 3 seconds before the first detect... ecm_selection: nat_x 1 qos 0: action 1. ecm_selection: nat_x 1 qos 0: action 1. start_wan: start_wan_if(0)! [1 init:start_wan_if +30] unit=0. update_wan_state(wan0_, 0, 0) convert_wan_nvram(wan0_) update_wan_state(wan0_, 1, 0) start_wan_if(0x0670): ifup:vlan10 _ifconfig: name=vlan10 flags=1043 IFUP addr= netmask= start_wan_if(0x0674): start auth:0 start_auth:: done start_wan_if(0x067e): start udhcpc:vlan10, 0 start_wan_if(): End. Enable USB power. Start USB with the original procedure. start_usb udhcpc_wan:: deconfig _ifconfig: name=vlan10 flags=1043 IFUP addr=0.0.0.0 netmask= wan_down(vlan10) wan_down(vlan10): . stop_auth:: done route_manip: cmd=DEL name=vlan10 addr=0.0.0.0 netmask=0.0.0.0 gateway=(null) metric=0 update_wan_state(wan0_, 3, 0) update_wan_state(wan0_, 4, 3) udhcpc:: deconfig done wanduck(0): NC send SYS_WAN_CABLE_UNPLUGGED_EVENT. # Enable direct rule [ 30.765938] wlan: [1420: I:ANY] vht su bfee 0 vht mu bfee 0 vht su bfer 1 vht mu bfer 1 vht impl bf 1 vht sounding dim 3 [ 30.768131] wlan: [1421: I:ANY] ol_ath_vap_set_param : Setting the following vdev params vap->iv_he_su_bfee: 0, vap->iv_he_su_bfer: 1 vap->iv_he_mu_bfee: 0, vap->iv_he_mu_bfer: 0 vap->iv_ [ 30.776101] wlan: [1421: I:ANY] ol_ath_vap_set_param : WMI: he_bf_cap = 0x12 [ 30.800942] wlan: [1422: I:ANY] ol_ath_vap_set_param : Setting the following vdev params vap->iv_he_su_bfee: 0, vap->iv_he_su_bfer: 0 vap->iv_he_mu_bfee: 0, vap->iv_he_mu_bfer: 0 vap->iv_ [ 30.805643] wlan: [1422: I:ANY] ol_ath_vap_set_param : WMI: he_bf_cap = 0x10 [ 30.830567] wlan: [1423: I:ANY] DES SSID SET=ASUS_50 [ 30.847151] [MLME] vap-0(ath1):wlan_mlme_stop_bss: disassoc/deauth all stations. iv_node_count: 1, peer_cnt: 1 [ 30.962818] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 [ 30.972819] [MLME] vap-0(ath1):wlan_mlme_stop_bss: disassoc/deauth all stations. iv_node_count: 1, peer_cnt: 1 [ 31.013056] DEVICE IS DOWN ifname=ath1 [ 31.013085] DEVICE IS DOWN ifname=ath1 [ 31.015978] [MLME] vap-0(ath1):wlan_mlme_stop_bss: disassoc/deauth all stations. iv_node_count: 1, peer_cnt: 1 [ 31.079040] wlan: [1433: I:ANY] vht su bfee 0 vht mu bfee 0 vht su bfer 1 vht mu bfer 1 vht impl bf 1 vht sounding dim 7 [ 31.081092] wlan: [1434: I:ANY] ol_ath_vap_set_param : Setting the following vdev params vap->iv_he_su_bfee: 0, vap->iv_he_su_bfer: 1 vap->iv_he_mu_bfee: 0, vap->iv_he_mu_bfer: 0 vap->iv_ [ 31.089241] wlan: [1434: I:ANY] ol_ath_vap_set_param : WMI: he_bf_cap = 0x12 [ 31.113588] wlan: [1435: I:ANY] DES SSID SET=ASUS_50 [ 31.133156] [MLME] vap-1(ath0):wlan_mlme_stop_bss: disassoc/deauth all stations. iv_node_count: 1, peer_cnt: 1 [ 31.163018] wlan: [0: I:ANY] OL vap start id: 1 + [ 31.163089] wlan: [0: I:ANY] OL vap_start - [ 31.202828] wlan: [1441: I:ANY] Mgmt Rate:6000(kbps) | Rate Code:0x10000003 [ 31.272819] ieee80211_ioctl_siwmode: imr.ifm_active=167772800, new mode=3, valid=1 [ 31.273192] [MLME] vap-1(ath0):wlan_mlme_stop_bss: disassoc/deauth all stations. iv_node_count: 1, peer_cnt: 1 [ 31.280055] wlan: [0: I:ANY] STOPPED EVENT for vap 1 (b8fa7400) [ 31.289504] wlan: [0: I:ANY] wmi_vdev_down id: 1 [ 31.353089] DEVICE IS DOWN ifname=ath0 [ 31.353120] DEVICE IS DOWN ifname=ath0 [ 31.355967] [MLME] vap-1(ath0):wlan_mlme_stop_bss: disassoc/deauth all stations. iv_node_count: 1, peer_cnt: 1 [ 31.383028] wlan: [0: I:ANY] OL vap start id: 1 + [ 31.383105] wlan: [0: I:ANY] OL vap_start - [ 31.422812] wlan: [1020: I:ANY] Mgmt Rate:6000(kbps) | Rate Code:0x10000003 [ 31.487738] __mc_netlink_receive: Enable bridge snooping! <rc_service> [i:rc] 1456:notify_rc restart_qca_lbd[1 init:init_main +32] recv signal 10 from pid [1456:rc] (from user) cmd[0]=restart_qca_lbd [1 init:handle_notifications +32] running: 3 qca_lbd [Mastiff]init handle_notifications() end [ 31.692637] wlan: [1484: I:ANY] [ath1]Band steering events being sent to PID:1484 [ 31.692679] wlan: [1484: I:ANY] [ath0]Band steering events being sent to PID:1484 [ 34.927212] wlan: [0: I:ANY] ieee80211_derive_chan : Overriding HE40 channel with HE20 channel [ 34.927264] wlan: [0: I:ANY] OL vap start id: 0 + [ 34.934740] wlan: [0: I:ANY] OL vap_start - add_beacon_vsie: cmd=hostapd_cli set_vsie -iath1 0 DD25F832E401010102010003143C526F9F78AF5E0749AFA5ADAE2C70635AED3B9307045AED3B93 [ 35.023024] wlan: [0: I:ANY] vht su bfee 0 vht mu bfee 0 vht su bfer 1 vht mu bfer 1 vht impl bf 1 vht sounding dim 3 [ 35.023090] wlan: [0: I:ANY] Setting Rx Decap type to 2 (Ethernet) [ 35.032624] wlan: [0: I:ANY] Setting Tx Encap type to 2 (Ethernet) [ 35.038708] wlan: [0: E:FILS discovery] target_if_fd_reconfig: 157: FILS is not enabled udhcpc_wan:: leasefail [ 41.435736] wlan: [1447: I:ANY] ol_ath_vap_set_param: Now supported MCAST RATE is 1000(kbps) and rate code: 0x10000103 [ 41.437084] wlan: [1448: I:ANY] ol_ath_vap_set_param: Now supported MCAST RATE is 6000(kbps) and rate code: 0x10000003 [FAUPGRADE][auto_firmware_check:(6371)]ntp_ready false udhcpc_wan:: leasefail [FAUPGRADE][auto_firmware_check:(6371)]ntp_ready false [ 93.602805] wlan: [0: I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_cac_timeout: 119: cac expired, chan 5500 curr time 4294760 [ 93.603049] wlan: [0: I:ANY] vht su bfee 0 vht mu bfee 0 vht su bfer 1 vht mu bfer 1 vht impl bf 1 vht sounding dim 7 [ 93.612125] wlan: [0: I:ANY] Setting Rx Decap type to 2 (Ethernet) [ 93.622844] wlan: [0: I:ANY] Setting Tx Encap type to 2 (Ethernet) [ 93.628924] wlan: [0: E:FILS discovery] target_if_fd_reconfig: 157: FILS is not enabled udhcpc_wan:: leasefail [FAUPGRADE][auto_firmware_check:(6371)]ntp_ready false