ASUS RT-AC88U

RT-AC88U

Asus RT-AC88U is an AC3100 router featuring 9 Ethernet ports over the integrated Broadcom and the external Realtek switch.

ModelVersionSoCCPU MHzCPU CoresFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
RT-AC88UBroadcom BCM4709C0KFEBG14002128512Broadcom BCM4366C0b/g/na/n/ac-9-1x 2.0, 1x 3.0
 Creating 3 MTD partitions on "brcmnand.0":
 0x000000000000-0x000000080000 : "boot"
 0x000000080000-0x000000200000 : "nvram"
 0x000000200000-0x000008000000 : "firmware"
 2 trx partitions found on MTD device firmware
 Creating 2 MTD partitions on "firmware":
 0x00000000001c-0x000000400000 : "linux"
 0x000000400000-0x000007e00000 : "ubi"
  • Boot to CFE Recovery Mode by holding the reset button while power-on.
  • Connect to the router with an ethernet cable.
  • Set IPv4 address of the computer to 192.168.1.2 subnet 255.255.255.0.
  • Reset NVRAM.
  • Upload the OpenWrt image.

CFE bootloader may reject flashing the image due to image integrity check. In that case, follow the instructions below.

  • Rename the OpenWrt image as firmware.trx.
  • Run a TFTP server on the computer and make it serve the firmware.trx file.
  • Run the URL below on a browser or curl.

http://192.168.1.1/do.htm?cmd=flash+-noheader+192.168.1.2:firmware.trx+flash0.trx

generic.debrick

In case of being unable to reach the CFE recovery web page, reset NVRAM by holding the WPS button while power-on until the LEDs flicker.

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

Interface Name Description
wan Interface for WAN Port
lan1 Interface for LAN 1 Port
lan2 Interface for LAN 2 Port
lan3 Interface for LAN 3 Port
lan4 Interface for LAN 4 Port
extsw Interface for Realtek Switch Ports

LAN5-8 ports (Realtek switch) work without the ability of configuring VLANs or ports individually. Reach this switch over the “extsw” interface.

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The ASUS RT-AC88U has the following buttons:

BUTTON Event
Reset Reset
WPS WPS
Wi-Fi Kill radios
LED Kill LEDs (doesn't work)
General
Brand ASUS
Model RT-AC88U
Versions
Device Type WiFi Router
Availability Available 2022
Comments - general
OpenWrt Support
Supported Since Commit https://git.openwrt.org/?p=openwrt/openwrt.git;a=commit;h=72b9b721d707b7f70109eb70b2a9f22449ceba08
Supported Since Release
Supported Current Release snapshot
Unsupported
Hardware
Bootloader CFE
Target bcm53xx
System-On-Chip Broadcom BCM4709C0KFEBG
CPU MHz 1400
Flash MB 128
RAM MB 512
Network
Ethernet 100M ports -
Ethernet Gbit ports 9
Switch Realtek RTL8365MB
Modem -
VLAN Yes
Comments - network ports
Wireless
WLAN 2.4GHz b/g/n
WLAN 5.0GHz a/n/ac
WLAN Hardware Broadcom BCM4366C0
Detachable Antennas 4
Comments - WLAN
Interfaces
USB ports 1x 2.0, 1x 3.0
SATA ports -
Serial Yes
JTAG Yes
Comments - USB & SATA ports
Misc
LED count 7
Button count 4
Power supply 19 VDC, 2.37 A
Links
Forum Topic URL
WikiDevi URL https://wikidevi.wi-cat.ru/ASUS_RT-AC88U
OEM device homepage URL https://www.asus.com/Networking-IoT-Servers/WiFi-Routers/ASUS-WiFi-Routers/RT-AC88U/
Firmware OEM Stock URL https://www.asus.com/Networking-IoT-Servers/WiFi-Routers/ASUS-WiFi-Routers/RT-AC88U/HelpDesk_BIOS/
Firmware OpenWrt Install URL https://downloads.openwrt.org/releases/22.03.0-rc5/targets/bcm53xx/generic/openwrt-22.03.0-rc5-bcm53xx-generic-asus_rt-ac88u-squashfs.trx
Firmware OpenWrt Upgrade URL https://downloads.openwrt.org/releases/22.03.0-rc5/targets/bcm53xx/generic/openwrt-22.03.0-rc5-bcm53xx-generic-asus_rt-ac88u-squashfs.trx
Edit the underlying data View/Edit data

Wireless LEDs can be configured via NVRAM variables.

  • 0:ledbh9 → Behaviour of 2.4GHz LED
  • 1:ledbh9 → Behaviour of 5GHz LED
  • 0x7 makes the wireless LEDs on, when radios are enabled, and blink when there's activity
  • 0x88 makes the wireless LEDs off by default and blink when there's activity

Example:

 nvram set 0:ledbh9=0x7 && nvram commit

Restart the router for the changes to take effect.

                                       CPU
                                ┌───────────────┐
                                │ gmac1 │ gmac2 │
                                └───┼───────┼───┘
                                    │       │
                                    └──┐ ┌──┘
                          ┌────────────┼─┼┐
                          │0 1 2 3 4 5 7 8│ BCM53012
                          └┼─┼─┼─┼─┼─┼────┘
                           │ │ │ │ └─┼──────────────┐
                           │ │ │ └───┼───────┐      │
                           │ │ └─────┼─┐     │      │
                           │ └───┐   │ │     │      │
                       ┌───┼─────┼───┘ │     │      │
              ┌────────┼┐  │     │     │     │      │
    RTL8365MB │0 1 2 3 6│  │     │     │     │      │
              └┼─┼─┼─┼──┘  │     │     │     │      │
   ┌───────────┘ │ │ │     │     │     │     │      │
   │     ┌───────┘ │ │     │     │     │     │      │         CPU0   CPU1
   │     │     ┌───┘ │     │     │     │     │      │          │       │
   │     │     │     │     │     │     │     │      │          │       │
┌──┼─────┼─────┼─────┼─────┼─────┼─────┼─────┼──────┼──┐   ┌───┼───────┼───┐
│ Lan5  Lan6  Lan7  Lan8  Lan4  Lan3  Lan2  Lan1 │ Wan │   │ Wlan0 │ Wlan1 │
└──────────────────────────────────────────────────────┘   └───────────────┘

RTL8365MB switch product page: https://www.realtek.com/en/products/communications-network-ics/item/rtl8365mb-vc-cg

Note: This will void your warranty!

  • To remove the cover and open the device, remove rubber feet and screws. Opening the plastic case will be painful, try not to break the tiny plastic pieces.

Main PCB:

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Serial connection parameters
for ASUS RT-AC88U
115200, 8N1, 3.3V

Connecting a serial cable before powering on the device will hang the bootloader. Connect the pins after powering on the device.

port.jtag general information about the JTAG port, JTAG cable, etc.

None so far.

Digital core power voltage set to 1.05V SHMOO VER 1.13 PKID07DC06011801080000000000001A103F01000000 S300001E7 00001420 RDLYW0 00000005 RDENW0 00000036 RDQSW0 0000000000111111111122222222223333333333444444444455555555556666 0123456789012345678901234567890123456789012345678901234567890123 00 ------+++++++++++++++++++++++X+++++++++++++++++++++++----------- 01 -------------+++++++++++++++++++++++X+++++++++++++++++++++++---- 02 -------------+++++++++++++++++++++++X+++++++++++++++++++++++---- 03 -----------++++++++++++++++++++++X++++++++++++++++++++++-------- 04 -------+++++++++++++++++++++++X++++++++++++++++++++++----------- 05 --------+++++++++++++++++++++++X+++++++++++++++++++++++--------- 06 ---------+++++++++++++++++++++X+++++++++++++++++++++------------ 07 -------+++++++++++++++++++++++X+++++++++++++++++++++++---------- 08 ---+++++++++++++++++++++++++X++++++++++++++++++++++++----------- 09 -----++++++++++++++++++++++++X+++++++++++++++++++++++----------- 10 ---++++++++++++++++++++++++X++++++++++++++++++++++++------------ 11 ---++++++++++++++++++++++X+++++++++++++++++++++----------------- 12 --++++++++++++++++++++++++X++++++++++++++++++++++++------------- 13 --+++++++++++++++++++++++X++++++++++++++++++++++---------------- 14 ---++++++++++++++++++++++++X++++++++++++++++++++++++------------ 15 -+++++++++++++++++++++++X++++++++++++++++++++++----------------- PW0 0000000000111111111122222222223333333333444444444455555555556666 0123456789012345678901234567890123456789012345678901234567890123 00 --+++++++++++++++++++++++++X+++++++++++++++++++++++++----------- 01 -------++++++++++++++++++++++++++X++++++++++++++++++++++++++---- 02 -------++++++++++++++++++++++++++X++++++++++++++++++++++++++---- 03 ------+++++++++++++++++++++++++X++++++++++++++++++++++++-------- 04 ++++++++++++++++++++++++++X++++++++++++++++++++++++++----------- 05 ---++++++++++++++++++++++++++X+++++++++++++++++++++++++--------- 06 ---++++++++++++++++++++++++X++++++++++++++++++++++++------------ 07 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++---------- 08 -++++++++++++++++++++++++++X+++++++++++++++++++++++++----------- 09 ---+++++++++++++++++++++++++X++++++++++++++++++++++++----------- 10 ++++++++++++++++++++++++++X+++++++++++++++++++++++++------------ 11 -+++++++++++++++++++++++X++++++++++++++++++++++----------------- 12 +++++++++++++++++++++++++X+++++++++++++++++++++++++------------- 13 +++++++++++++++++++++++X+++++++++++++++++++++++----------------- 14 -+++++++++++++++++++++++++X+++++++++++++++++++++++++------------ 15 +++++++++++++++++++++++X+++++++++++++++++++++++----------------- NW0 0000000000111111111122222222223333333333444444444455555555556666 0123456789012345678901234567890123456789012345678901234567890123 00 -------++++++++++++++++++++++++X++++++++++++++++++++++++-------- 01 -------------+++++++++++++++++++++++++X+++++++++++++++++++++++-- 02 --------------+++++++++++++++++++++++++X++++++++++++++++++++++-- 03 -----------+++++++++++++++++++++++X+++++++++++++++++++++++------ 04 -------++++++++++++++++++++++++X+++++++++++++++++++++++--------- 05 --------++++++++++++++++++++++++X+++++++++++++++++++++++-------- 06 ----------+++++++++++++++++++++++X++++++++++++++++++++++-------- 07 -------++++++++++++++++++++++++X+++++++++++++++++++++++--------- 08 ---++++++++++++++++++++++++++X+++++++++++++++++++++++++--------- 09 -----+++++++++++++++++++++++++X++++++++++++++++++++++++--------- 10 --+++++++++++++++++++++++++X+++++++++++++++++++++++++----------- 11 ----+++++++++++++++++++++++X++++++++++++++++++++++-------------- 12 -+-++++++++++++++++++++++++X++++++++++++++++++++++++------------ 13 -+++++++++++++++++++++++++X++++++++++++++++++++++++------------- 14 --++++++++++++++++++++++++++X+++++++++++++++++++++++++---------- 15 -+++++++++++++++++++++++X+++++++++++++++++++++++---------------- WRDQW0 0000000000111111111122222222223333333333444444444455555555556666 0123456789012345678901234567890123456789012345678901234567890123 00 ++++++++++++++++++++++X+++++++++++++++++++++------------+++++++- 01 +++++++++++++++++++++++++X++++++++++++++++++++++++------+++++++- 02 +++++++++++++++++++++++++X+++++++++++++++++++++++++--------++++- 03 +++++++++++++++++++++++++X+++++++++++++++++++++++++------++++++- 04 ++++++++++++++++++++++X+++++++++++++++++++++-------------++++++- 05 +++++++++++++++++++++++X++++++++++++++++++++++----------+++++++- 06 +++++++++++++++++++++++X+++++++++++++++++++++++----------++++++- 07 +++++++++++++++++++++++X+++++++++++++++++++++++---------+++++++- 08 ++++++++++++++++++++++X++++++++++++++++++++++-----------+++++++- 09 ++++++++++++++++++++++++X+++++++++++++++++++++++-------++++++++- 10 ++++++++++++++++++++++++X+++++++++++++++++++++++-------++++++++- 11 ++++++++++++++++++++++X+++++++++++++++++++++-----------++++++++- 12 ++++++++++++++++++++++X+++++++++++++++++++++-----------++++++++- 13 +++++++++++++++++++++X+++++++++++++++++++++-------------+++++++- 14 ++++++++++++++++++++++X+++++++++++++++++++++------------+++++++- 15 +++++++++++++++++++++X++++++++++++++++++++--------------+++++++- WRDMW0 00000023 WRDMW0 00000022 ADDR 0000000000111111111122222222223333333333444444444455555555556666 0123456789012345678901234567890123456789012345678901234567890123 00 ++++++++++++++++++++S++++++++++X++++++++++++++++++++++++++++++++ Decompressing...done CFE version 7.14.131.1608 (r589038) based on BBP 1.0.37 for BCM947XX (32bit,SP,) Build Date: 二 11月 17 16:33:56 CST 2015 (ham@xpdev) Copyright (C) 2000-2008 Broadcom Corporation. Init Arena Init Devs. Boot partition size = 262144(0x40000) DDR Clock: 800 MHz Info: DDR frequency set from clkfreq=1400,*800* et2: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.131.1608 (r589038) CPU type 0x0: 1400MHz Tot mem: 524288 KBytes CFE mem: 0x00F00000 - 0x017ABEC8 (9092808) Data: 0x00F5401C - 0x00F549C4 (2472) BSS: 0x00F549D0 - 0x00FA9EC8 (349432) Heap: 0x00FA9EC8 - 0x017A9EC8 (8388608) Stack: 0x017A9EC8 - 0x017ABEC8 (8192) Text: 0x00F00000 - 0x00F4A1E0 (303584) rtl8354mb initialized(0)(retry 0) rtk port_phyEnableAll ok rtk port_macForceLink_set ext_Port1 ok get ok, chk 0x1311:1016(0x1016), 0x1305:c010(b4~b7:0x1) Device eth0: hwaddr 04-D9-F5-52-D8-90, ipaddr 192.168.1.1, mask 255.255.255.0 gateway not set, nameserver not set Null Rescue Flag. boot the image... go load Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null) Loading: TFTP Server. ..tftp retry wait 0 Failed. Could not load :: Timeout occured Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null) Loading: .... 4486208 bytes read Entry at 0x00008000 Closing network. Starting program at 0x00008000 console [ttyS0] enabled, bootconsole disabled serial8250.0: ttyS1 at MMIO 0x18000400 (irq = 117) is a 16550 brd: module loaded loop: module loaded pflash: found no supported devices bcmsflash: found no supported devices Boot partition size = 524288(0x80000) lookup_nflash_rootfs_offset: offset = 0x200000 nflash: squash filesystem with lzma found at block 30 Creating 4 MTD partitions on "nflash": 0x000000000000-0x000000080000 : "boot" 0x000000080000-0x000000200000 : "nvram" 0x000000200000-0x000004000000 : "linux" 0x0000003c2af4-0x000004000000 : "rootfs" PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 === PPTP init === Mirror/redirect action on u32 classifier Performance counters on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (8045 buckets, 32180 max) ctnetlink v0.93: registering with nfnetlink. xt_time: kernel timezone is -0000 ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team NET: Registered protocol family 17 NET: Registered protocol family 15 L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> Registering the dns_resolver key type Northstar brcmnand NAND Flash Controller driver, Version 0.1 (c) Broadcom Inc. 2012 NAND device: Manufacturer ID: 0xc8, Chip ID: 0xd1 (Unknown NAND 128MiB 3,3V 8-bit) Spare area=64 eccbytes 56, ecc bytes located at: 2 3 4 5 6 7 8 9 10 11 12 13 14 15 18 19 20 21 22 23 24 25 26 27 28 29 30 31 34 35 36 37 38 39 40 41 42 43 44 45 46 47 50 51 52 53 54 55 56 57 58 59 60 61 62 63 Available 7 bytes at (off,len): (1,1) (16,2) (32,2) (48,2) (0,0) (0,0) (0,0) (0,0) Scanning device for bad blocks Options: NO_AUTOINCR,NO_READRDY, Creating 1 MTD partitions on "brcmnand": 0x000004000000-0x000008000000 : "brcmnand" VFS: Mounted root (squashfs filesystem) readonly on device 31:3. devtmpfs: mounted Freeing init memory: 288K init_main start 1: set_action 0 Hit ENTER for console...


Digital core power voltage set to 1.05V SHMOO VER 1.13 PKID07DC06011801080000000000001A103F01000000 S300001E3 00001440 RDLYW0 00000005 RDENW0 00000036 RDQSW0 0000000000111111111122222222223333333333444444444455555555556666 0123456789012345678901234567890123456789012345678901234567890123 00 -------+++++++++++++++++++++++X++++++++++++++++++++++----------- 01 -------------+++++++++++++++++++++++X+++++++++++++++++++++++---- 02 --------------+++++++++++++++++++++++X++++++++++++++++++++++---- 03 -----------++++++++++++++++++++++X++++++++++++++++++++++-------- 04 --------++++++++++++++++++++++X+++++++++++++++++++++------------ 05 --------+++++++++++++++++++++++X+++++++++++++++++++++++--------- 06 ---------+++++++++++++++++++++X+++++++++++++++++++++------------ 07 -------+++++++++++++++++++++++X+++++++++++++++++++++++---------- 08 --+++++++++++++++++++++++++X+++++++++++++++++++++++++----------- 09 ----++++++++++++++++++++++++X+++++++++++++++++++++++------------ 10 ---++++++++++++++++++++++++X++++++++++++++++++++++++------------ 11 ---++++++++++++++++++++++X+++++++++++++++++++++----------------- 12 -+++++++++++++++++++++++++X++++++++++++++++++++++++------------- 13 -+++++++++++++++++++++++X+++++++++++++++++++++++---------------- 14 ---++++++++++++++++++++++++X+++++++++++++++++++++++------------- 15 --++++++++++++++++++++++X++++++++++++++++++++++----------------- PW0 0000000000111111111122222222223333333333444444444455555555556666 0123456789012345678901234567890123456789012345678901234567890123 00 -++++++++++++++++++++++++++X++++++++++++++++++++++++++---------- 01 --------++++++++++++++++++++++++++X+++++++++++++++++++++++++---- 02 --------++++++++++++++++++++++++++X+++++++++++++++++++++++++---- 03 ------+++++++++++++++++++++++++X++++++++++++++++++++++++-------- 04 -+++++++++++++++++++++++++X+++++++++++++++++++++++++------------ 05 ----+++++++++++++++++++++++++X+++++++++++++++++++++++++--------- 06 ----++++++++++++++++++++++++X+++++++++++++++++++++++------------ 07 ---+++++++++++++++++++++++++X+++++++++++++++++++++++++---------- 08 -++++++++++++++++++++++++++X+++++++++++++++++++++++++----------- 09 ---+++++++++++++++++++++++++X++++++++++++++++++++++++----------- 10 -+++++++++++++++++++++++++X+++++++++++++++++++++++++------------ 11 --++++++++++++++++++++++X++++++++++++++++++++++----------------- 12 +++++++++++++++++++++++++X+++++++++++++++++++++++++------------- 13 ++++++++++++++++++++++++X+++++++++++++++++++++++---------------- 14 --+++++++++++++++++++++++++X++++++++++++++++++++++++------------ 15 +++++++++++++++++++++++X+++++++++++++++++++++++----------------- NW0 0000000000111111111122222222223333333333444444444455555555556666 0123456789012345678901234567890123456789012345678901234567890123 00 ------++++++++++++++++++++++++X++++++++++++++++++++++++--------- 01 -------------+++++++++++++++++++++++++X+++++++++++++++++++++++-- 02 -------------++++++++++++++++++++++++X+++++++++++++++++++++++--- 03 -----------+++++++++++++++++++++++X+++++++++++++++++++++++------ 04 ---------+++++++++++++++++++++++X+++++++++++++++++++++++-------- 05 ---------++++++++++++++++++++++++X+++++++++++++++++++++++------- 06 ---------++++++++++++++++++++++++X+++++++++++++++++++++++------- 07 --------+++++++++++++++++++++++X+++++++++++++++++++++++--------- 08 ---++++++++++++++++++++++++++X+++++++++++++++++++++++++--------- 09 -----+++++++++++++++++++++++++X++++++++++++++++++++++++--------- 10 --+++++++++++++++++++++++++X+++++++++++++++++++++++++----------- 11 ----+++++++++++++++++++++++X++++++++++++++++++++++-------------- 12 --+++++++++++++++++++++++++X++++++++++++++++++++++++------------ 13 -+++++++++++++++++++++++++X++++++++++++++++++++++++------------- 14 ---+++++++++++++++++++++++++X++++++++++++++++++++++++----------- 15 --+++++++++++++++++++++++X++++++++++++++++++++++---------------- WRDQW0 0000000000111111111122222222223333333333444444444455555555556666 0123456789012345678901234567890123456789012345678901234567890123 00 ++++++++++++++++++++++X++++++++++++++++++++++----------++++++++- 01 +++++++++++++++++++++++++X+++++++++++++++++++++++++-----+++++++- 02 +++++++++++++++++++++++++X+++++++++++++++++++++++++-------+++++- 03 +++++++++++++++++++++++++X+++++++++++++++++++++++++------++++++- 04 ++++++++++++++++++++++X++++++++++++++++++++++------------++++++- 05 +++++++++++++++++++++++X+++++++++++++++++++++++---------+++++++- 06 +++++++++++++++++++++++X+++++++++++++++++++++++----------++++++- 07 +++++++++++++++++++++++X+++++++++++++++++++++++---------+++++++- 08 ++++++++++++++++++++++X++++++++++++++++++++++----------++++++++- 09 ++++++++++++++++++++++++X+++++++++++++++++++++++-------++++++++- 10 +++++++++++++++++++++++X+++++++++++++++++++++++-------+++++++++- 11 ++++++++++++++++++++++X++++++++++++++++++++++----------++++++++- 12 ++++++++++++++++++++++X+++++++++++++++++++++-----------++++++++- 13 +++++++++++++++++++++X++++++++++++++++++++--------------+++++++- 14 ++++++++++++++++++++++X+++++++++++++++++++++------------+++++++- 15 ++++++++++++++++++++X++++++++++++++++++++--------------++++++++- WRDMW0 00000023 WRDMW0 00000022 ADDR 0000000000111111111122222222223333333333444444444455555555556666 0123456789012345678901234567890123456789012345678901234567890123 00 ++++++++++++++++++++S++++++++++X++++++++++++++++++++++++++++++++ Decompressing...done CFE version 7.14.131.1608 (r589038) based on BBP 1.0.37 for BCM947XX (32bit,SP,) Build Date: 二 11月 17 16:33:56 CST 2015 (ham@xpdev) Copyright (C) 2000-2008 Broadcom Corporation. Init Arena Init Devs. Boot partition size = 262144(0x40000) DDR Clock: 800 MHz Info: DDR frequency set from clkfreq=1400,*800* et1: Broadcom BCM47XX 10/100/1000 Mbps Ethernet Controller 7.14.131.1608 (r589038) CPU type 0x0: 1400MHz Tot mem: 524288 KBytes CFE mem: 0x00F00000 - 0x017ABEC8 (9092808) Data: 0x00F5401C - 0x00F549C4 (2472) BSS: 0x00F549D0 - 0x00FA9EC8 (349432) Heap: 0x00FA9EC8 - 0x017A9EC8 (8388608) Stack: 0x017A9EC8 - 0x017ABEC8 (8192) Text: 0x00F00000 - 0x00F4A1E0 (303584) rtl8354mb initialized(0)(retry 0) rtk port_phyEnableAll ok rtk port_macForceLink_set ext_Port1 ok get ok, chk 0x1311:1016(0x1016), 0x1305:c010(b4~b7:0x1) Device eth0: hwaddr 04-D9-F5-52-D8-90, ipaddr 192.168.1.1, mask 255.255.255.0 gateway not set, nameserver not set Null Rescue Flag. boot the image... go load Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null) Loading: TFTP Server. ..tftp retry wait 0 ..tftp retry wait 1 ..tftp retry wait 2 ..tftp retry wait 3 ..tftp retry wait 4 Failed. Could not load :: Timeout occured Loader:raw Filesys:raw Dev:nflash0.os File: Options:(null) Loading: ... 2359004 bytes read Entry at 0x00008000 Closing network. Starting program at 0x00008000 Uncompressing Linux... done, booting the kernel. [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.120 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 11.2.0 r19426-2b1941e47d) 11.2.0, GNU ld (GNU Binutils) 2.37) #0 SMP Fri Jun 10 07:20:21 2022 [ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Asus RT-AC88U [ 0.000000] earlycon: ns16550 at MMIO 0x18000300 (options '115200n8') [ 0.000000] printk: bootconsole [ns16550] enabled [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Hit pending asynchronous external abort (FSR=0x00001c06) during first unmask, this is most likely caused by a firmware/bootloader bug. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] HighMem [mem 0x0000000008000000-0x000000009fffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000007ffffff] [ 0.000000] node 0: [mem 0x0000000088000000-0x000000009fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000009fffffff] [ 0.000000] On node 0 totalpages: 131072 [ 0.000000] Normal zone: 288 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 32768 pages, LIFO batch:7 [ 0.000000] HighMem zone: 98304 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 14 pages/cpu s27340 r8192 d21812 u57344 [ 0.000000] pcpu-alloc: s27340 r8192 d21812 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 130784 [ 0.000000] Kernel command line: earlycon [ 0.000000] Dentry cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Inode-cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 510312K/524288K available (5868K kernel code, 568K rwdata, 812K rodata, 1024K init, 298K bss, 13976K reserved, 0K cma-reserved, 393216K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C: DT/platform modifies aux control register: 0x0a130000 -> 0x3a530000 [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 cache controller enabled, 16 ways, 256 kB [ 0.000000] L2C-310: CACHE_ID 0x410000c8, AUX_CTRL 0x7e530001 [ 0.000008] sched_clock: 64 bits at 700MHz, resolution 1ns, wraps every 4398046511103ns [ 0.008109] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0xa17102bcf3, max_idle_ns: 440795224838 ns [ 0.019283] Switching to timer-based delay loop, resolution 1ns [ 0.025449] Calibrating delay loop (skipped), value calculated using timer frequency.. 1400.00 BogoMIPS (lpj=7000000) [ 0.036184] pid_max: default: 32768 minimum: 301 [ 0.040913] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.048298] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.056664] CPU: Testing write buffer coherency: ok [ 0.061608] CPU0: Spectre v2: using BPIALL workaround [ 0.066924] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.073091] Setting up static identity map for 0x100000 - 0x10003c [ 0.079463] rcu: Hierarchical SRCU implementation. [ 0.084447] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.092371] smp: Bringing up secondary CPUs ... [ 0.097560] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.097568] CPU1: Spectre v2: using BPIALL workaround [ 0.108432] smp: Brought up 1 node, 2 CPUs [ 0.112552] SMP: Total of 2 processors activated (2800.00 BogoMIPS). [ 0.118957] CPU: WARNING: CPU(s) started in wrong/inconsistent modes (primary CPU mode 0x13) [ 0.127455] CPU: This may indicate a broken bootloader or firmware. [ 0.135875] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.145845] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.152853] pinctrl core: initialized pinctrl subsystem [ 0.158833] NET: Registered protocol family 16 [ 0.163819] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.171389] thermal_sys: Registered thermal governor 'step_wise' [ 0.193744] clocksource: Switched to clocksource arm_global_timer [ 0.206788] NET: Registered protocol family 2 [ 0.211343] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.219134] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.227647] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.235472] TCP bind hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.242597] TCP: Hash tables configured (established 1024 bind 1024) [ 0.249102] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.255744] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.262975] NET: Registered protocol family 1 [ 0.267437] PCI: CLS 0 bytes, default 64 [ 0.273099] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.281654] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.287538] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.298035] bounce: pool size: 64 pages [ 0.301958] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 0.310822] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.318660] printk: console [ttyS0] disabled [ 0.323114] 18000300.serial: ttyS0 at MMIO 0x18000300 (irq = 26, base_baud = 7812500) is a 16550 [ 0.332044] printk: console [ttyS0] enabled [ 0.340454] printk: bootconsole [ns16550] disabled [ 0.351049] bcm2835-rng 18004000.rng: hwrng registered [ 1.035415] random: crng init done [ 1.039666] nand: device found, Manufacturer ID: 0xc8, Chip ID: 0xd1 [ 1.046090] nand: ESMT NAND 128MiB 3,3V 8-bit [ 1.050461] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.058067] iproc_nand 18028000.nand-controller: detected 128MiB total, 128KiB blocks, 2KiB pages, 16B OOB, 8-bit, BCH-8 [ 1.068979] Scanning device for bad blocks [ 1.977627] 3 fixed-partitions partitions found on MTD device brcmnand.0 [ 1.984362] Creating 3 MTD partitions on "brcmnand.0": [ 1.989512] 0x000000000000-0x000000080000 : "boot" [ 1.994832] 0x000000080000-0x000000200000 : "nvram" [ 2.000191] 0x000000200000-0x000008000000 : "firmware" [ 2.006784] 2 trx partitions found on MTD device firmware [ 2.012201] Creating 2 MTD partitions on "firmware": [ 2.017199] 0x00000000001c-0x000000400000 : "linux" [ 2.022089] mtd: partition "linux" doesn't start on an erase/write block boundary -- force read-only [ 2.031725] 0x000000400000-0x000007e00000 : "ubi" [ 2.039010] bcm_iproc 18029200.spi: using bspi-mspi mode [ 2.046279] iproc-mdio 18003000.mdio: Broadcom iProc MDIO bus registered [ 2.054525] b53-srab-switch 18007000.ethernet-switch: found switch: BCM53012, rev 0 [ 2.062390] bgmac_bcma: Broadcom 47xx GBit MAC driver loaded [ 2.068492] bcma-host-soc 18000000.axi: bus0: Found chip with id 53030, rev 0x00 and package 0x00 [ 2.077467] bcma-host-soc 18000000.axi: bus0: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x2A, class 0x0) [ 2.088045] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22 [ 2.088054] bcma-host-soc 18000000.axi: bus0: Core 1 found: Chipcommon B (manuf 0x4BF, id 0x50B, rev 0x05, class 0x0) [ 2.098788] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22 [ 2.098796] bcma-host-soc 18000000.axi: bus0: Core 2 found: DMA (manuf 0x4BF, id 0x502, rev 0x04, class 0x0) [ 2.108791] bcma-host-soc 18000000.axi: bus0: Core 3 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x07, class 0x0) [ 2.119201] bcma-host-soc 18000000.axi: bus0: Core 4 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x07, class 0x0) [ 2.129603] bcma-host-soc 18000000.axi: bus0: Core 5 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x07, class 0x0) [ 2.140022] bcma-host-soc 18000000.axi: bus0: Core 6 found: GBit MAC (manuf 0x4BF, id 0x82D, rev 0x07, class 0x0) [ 2.150382] bcma-host-soc 18000000.axi: bus0: Core 7 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x07, class 0x0) [ 2.160922] bcma-host-soc 18000000.axi: bus0: Core 8 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x07, class 0x0) [ 2.171462] bcma-host-soc 18000000.axi: bus0: Core 9 found: PCIe Gen 2 (manuf 0x4BF, id 0x501, rev 0x07, class 0x0) [ 2.182021] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22 [ 2.182029] bcma-host-soc 18000000.axi: bus0: Core 10 found: ARM Cortex A9 core (ihost) (manuf 0x4BF, id 0x510, rev 0x07, class 0x0) [ 2.194068] bcma-host-soc 18000000.axi: bus0: Core 11 found: USB 2.0 (manuf 0x4BF, id 0x504, rev 0x07, class 0x0) [ 2.204446] bcma-host-soc 18000000.axi: bus0: Core 12 found: USB 3.0 (manuf 0x4BF, id 0x505, rev 0x07, class 0x0) [ 2.214836] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22 [ 2.214843] bcma-host-soc 18000000.axi: bus0: Core 13 found: SDIO3 (manuf 0x4BF, id 0x503, rev 0x01, class 0x0) [ 2.225047] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22 [ 2.225055] bcma-host-soc 18000000.axi: bus0: Core 14 found: I2S (manuf 0x4BF, id 0x834, rev 0x03, class 0x0) [ 2.235088] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22 [ 2.235095] bcma-host-soc 18000000.axi: bus0: Core 15 found: ARM Cortex A9 JTAG (manuf 0x4BF, id 0x506, rev 0x01, class 0x0) [ 2.246434] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22 [ 2.246441] bcma-host-soc 18000000.axi: bus0: Core 16 found: Denali DDR2/DDR3 memory controller (manuf 0x4BF, id 0x507, rev 0x01, class 0x0) [ 2.259167] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22 [ 2.259173] bcma-host-soc 18000000.axi: bus0: Core 17 found: ROM (manuf 0x4BF, id 0x508, rev 0x08, class 0x0) [ 2.269230] bcma-host-soc 18000000.axi: bus0: Core 18 found: NAND flash controller (manuf 0x4BF, id 0x509, rev 0x01, class 0x0) [ 2.280839] bcma-host-soc 18000000.axi: bus0: bcma_of_get_irq() failed with rc=-22 [ 2.280846] bcma-host-soc 18000000.axi: bus0: Core 19 found: SPI flash controller (manuf 0x4BF, id 0x50A, rev 0x01, class 0x0) [ 2.292306] bcma-host-soc 18000000.axi: bus0: Flash type not supported [ 2.309752] bcma-host-soc 18000000.axi: bus0: Using SPROM revision 8 provided by platform. [ 2.309987] bgmac_bcma bcma0:3: Found PHY addr: 0 [ 2.314777] bgmac_bcma bcma0:3: Support for Roboswitch not implemented [ 2.321328] bgmac_bcma bcma0:3: Invalid MAC addr: 00:00:00:00:00:00 [ 2.327624] bgmac_bcma bcma0:3: Using random MAC: 3a:ab:f9:8c:d9:8e [ 2.334868] b53-srab-switch b53-srab-switch: invalid resource [ 2.340659] b53-srab-switch: probe of b53-srab-switch failed with error -22 [ 2.348392] bgmac_bcma bcma0:4: Found PHY addr: 30 (NOREGS) [ 2.354029] bgmac_bcma bcma0:4: Support for Roboswitch not implemented [ 2.361885] bgmac_bcma bcma0:5: Found PHY addr: 0 [ 2.366669] bgmac_bcma bcma0:5: Support for Roboswitch not implemented [ 2.373220] bgmac_bcma bcma0:5: Invalid MAC addr: 00:00:00:00:00:00 [ 2.379525] bgmac_bcma bcma0:5: Using random MAC: 56:23:b5:fa:cf:00 [ 2.387126] bgmac_bcma bcma0:6: Unsupported core_unit 3 [ 2.392412] bgmac_bcma: probe of bcma0:6 failed with error -524 [ 2.398494] pcie_iproc_bcma bcma0:7: host bridge /axi@18000000/pcie@12000 ranges: [ 2.406056] pcie_iproc_bcma bcma0:7: No bus range found for /axi@18000000/pcie@12000, using [bus 00-ff] [ 2.415669] OF: /axi@18000000/pcie@12000: Missing device_type [ 2.421430] pcie_iproc_bcma bcma0:7: non-prefetchable memory resource required [ 2.543735] pcie_iproc_bcma bcma0:7: link: UP [ 2.548220] pcie_iproc_bcma bcma0:7: PCI host bridge to bus 0000:00 [ 2.554535] pci_bus 0000:00: root bus resource [bus 00-ff] [ 2.560033] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fffffff] [ 2.566966] pci 0000:00:00.0: [14e4:d612] type 01 class 0x060400 [ 2.572986] pci_bus 0000:00: 2-byte config write to 0000:00:00.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.582720] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold [ 2.589619] PCI: bus0: Fast back to back transfers disabled [ 2.595236] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.603383] pci 0000:01:00.0: [14e4:4365] type 00 class 0x028000 [ 2.609438] pci_bus 0000:01: 2-byte config write to 0000:01:00.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.619142] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit] [ 2.625961] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x007fffff 64bit] [ 2.632768] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x000fffff 64bit pref] [ 2.640095] pci 0000:01:00.0: supports D1 D2 [ 2.645149] PCI: bus1: Fast back to back transfers disabled [ 2.650743] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.657417] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x08bfffff] [ 2.664234] pci 0000:00:00.0: BAR 9: assigned [mem 0x08c00000-0x08cfffff 64bit pref] [ 2.671994] pci 0000:01:00.0: BAR 2: assigned [mem 0x08000000-0x087fffff 64bit] [ 2.679338] pci 0000:01:00.0: BAR 4: assigned [mem 0x08c00000-0x08cfffff 64bit pref] [ 2.687120] pci 0000:01:00.0: BAR 0: assigned [mem 0x08800000-0x08807fff 64bit] [ 2.694460] pci 0000:00:00.0: PCI bridge to [bus 01] [ 2.699435] pci 0000:00:00.0: bridge window [mem 0x08000000-0x08bfffff] [ 2.706247] pci 0000:00:00.0: bridge window [mem 0x08c00000-0x08cfffff 64bit pref] [ 2.714200] pcie_iproc_bcma bcma0:8: host bridge /axi@18000000/pcie@13000 ranges: [ 2.721717] pcie_iproc_bcma bcma0:8: No bus range found for /axi@18000000/pcie@13000, using [bus 00-ff] [ 2.731340] pcie_iproc_bcma bcma0:8: non-prefetchable memory resource required [ 2.853732] pcie_iproc_bcma bcma0:8: link: UP [ 2.858223] pcie_iproc_bcma bcma0:8: PCI host bridge to bus 0001:00 [ 2.864544] pci_bus 0001:00: root bus resource [bus 00-ff] [ 2.870043] pci_bus 0001:00: root bus resource [mem 0x20000000-0x27ffffff] [ 2.876968] pci 0001:00:00.0: [14e4:d612] type 01 class 0x060400 [ 2.882987] pci_bus 0001:00: 2-byte config write to 0001:00:00.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.892712] pci 0001:00:00.0: PME# supported from D0 D3hot D3cold [ 2.899598] PCI: bus0: Fast back to back transfers disabled [ 2.905214] pci 0001:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 2.913363] pci 0001:01:00.0: [14e4:4365] type 00 class 0x028000 [ 2.919413] pci_bus 0001:01: 2-byte config write to 0001:01:00.0 offset 0x4 may corrupt adjacent RW1C bits [ 2.929117] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x00007fff 64bit] [ 2.935937] pci 0001:01:00.0: reg 0x18: [mem 0x00000000-0x007fffff 64bit] [ 2.942744] pci 0001:01:00.0: reg 0x20: [mem 0x00000000-0x000fffff 64bit pref] [ 2.950070] pci 0001:01:00.0: supports D1 D2 [ 2.955121] PCI: bus1: Fast back to back transfers disabled [ 2.960718] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01 [ 2.967382] pci 0001:00:00.0: BAR 8: assigned [mem 0x20000000-0x20bfffff] [ 2.974200] pci 0001:00:00.0: BAR 9: assigned [mem 0x20c00000-0x20cfffff 64bit pref] [ 2.981961] pci 0001:01:00.0: BAR 2: assigned [mem 0x20000000-0x207fffff 64bit] [ 2.989305] pci 0001:01:00.0: BAR 4: assigned [mem 0x20c00000-0x20cfffff 64bit pref] [ 2.997082] pci 0001:01:00.0: BAR 0: assigned [mem 0x20800000-0x20807fff 64bit] [ 3.004419] pci 0001:00:00.0: PCI bridge to [bus 01] [ 3.009394] pci 0001:00:00.0: bridge window [mem 0x20000000-0x20bfffff] [ 3.016208] pci 0001:00:00.0: bridge window [mem 0x20c00000-0x20cfffff 64bit pref] [ 3.024159] pcie_iproc_bcma bcma0:9: host bridge /axi@18000000/pcie@14000 ranges: [ 3.031675] pcie_iproc_bcma bcma0:9: No bus range found for /axi@18000000/pcie@14000, using [bus 00-ff] [ 3.041299] pcie_iproc_bcma bcma0:9: non-prefetchable memory resource required [ 3.163735] pcie_iproc_bcma bcma0:9: PHY or data link is INACTIVE! [ 3.169937] pcie_iproc_bcma bcma0:9: no PCIe EP device detected [ 3.176726] bcm47xx-wdt bcm47xx-wdt.0: BCM47xx Watchdog Timer enabled (30 seconds, Software Timer) [ 3.185798] bcma-host-soc 18000000.axi: bus0: Bus registered [ 3.192336] NET: Registered protocol family 10 [ 3.197814] Segment Routing with IPv6 [ 3.201545] NET: Registered protocol family 17 [ 3.206102] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 3.219296] 8021q: 802.1Q VLAN Support v1.8 [ 3.223542] Registering SWP/SWPB emulation handler [ 3.231005] b53-srab-switch 18007000.ethernet-switch: found switch: BCM53012, rev 0 [ 3.357740] b53-srab-switch 18007000.ethernet-switch lan4 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] (irq=POLL) [ 3.370172] b53-srab-switch 18007000.ethernet-switch lan3 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] (irq=POLL) [ 3.382570] b53-srab-switch 18007000.ethernet-switch lan2 (uninitialized): PHY [dsa-0.0:02] driver [Generic PHY] (irq=POLL) [ 3.394976] b53-srab-switch 18007000.ethernet-switch lan1 (uninitialized): PHY [dsa-0.0:03] driver [Generic PHY] (irq=POLL) [ 3.407431] b53-srab-switch 18007000.ethernet-switch wan (uninitialized): PHY [dsa-0.0:04] driver [Generic PHY] (irq=POLL) [ 3.420088] b53-srab-switch 18007000.ethernet-switch: Using legacy PHYLIB callbacks. Please migrate to PHYLINK! [ 3.430946] DSA: tree 0 setup [ 3.434249] UBI: auto-attach mtd4 [ 3.437592] ubi0: attaching mtd4 [ 4.068983] ubi0: scanning is finished [ 4.081365] ubi0: attached mtd4 (name "ubi", size 122 MiB) [ 4.086909] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.093813] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.100612] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.107599] ubi0: good PEBs: 976, bad PEBs: 0, corrupted PEBs: 0 [ 4.113615] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 4.120862] ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 145045326 [ 4.129933] ubi0: available PEBs: 0, total reserved PEBs: 976, PEBs reserved for bad PEB handling: 20 [ 4.139226] ubi0: background thread "ubi_bgt0d" started, PID 455 [ 4.146089] block ubiblock0_0: created from ubi0:0(rootfs) [ 4.151603] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 4.162418] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 4.170386] Freeing unused kernel memory: 1024K [ 4.203854] Run /sbin/init as init process [ 4.207957] with arguments: [ 4.207960] /sbin/init [ 4.207962] with environment: [ 4.207964] HOME=/ [ 4.207967] TERM=linux [ 4.406746] init: Console is alive [ 4.410350] init: - watchdog - [ 4.689876] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.755786] usbcore: registered new interface driver usbfs [ 4.761380] usbcore: registered new interface driver hub [ 4.766793] usbcore: registered new device driver usb [ 4.775033] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 4.782343] ehci-fsl: Freescale EHCI Host controller driver [ 4.789523] ehci-platform: EHCI generic platform driver [ 4.797389] ehci-platform 18021000.usb: EHCI Host Controller [ 4.799892] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.803101] ehci-platform 18021000.usb: new USB bus registered, assigned bus number 1 [ 4.810164] ohci-platform: OHCI generic platform driver [ 4.817373] ehci-platform 18021000.usb: irq 45, io mem 0x18021000 [ 4.822654] ohci-platform 18022000.usb: Generic Platform OHCI controller [ 4.835447] ohci-platform 18022000.usb: new USB bus registered, assigned bus number 2 [ 4.843387] ohci-platform 18022000.usb: irq 45, io mem 0x18022000 [ 4.853799] ehci-platform 18021000.usb: USB 2.0 started, EHCI 1.00 [ 4.860496] hub 1-0:1.0: USB hub found [ 4.864391] hub 1-0:1.0: 2 ports detected [ 4.918297] hub 2-0:1.0: USB hub found [ 4.922114] hub 2-0:1.0: 2 ports detected [ 4.953233] xhci-hcd 18023000.usb: xHCI Host Controller [ 4.958526] xhci-hcd 18023000.usb: new USB bus registered, assigned bus number 3 [ 4.966184] xhci-hcd 18023000.usb: hcc params 0x02501164 hci version 0x100 quirks 0x0000100000010010 [ 4.975389] xhci-hcd 18023000.usb: irq 46, io mem 0x18023000 [ 4.982555] hub 3-0:1.0: USB hub found [ 4.986414] hub 3-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 4.993713] xhci-hcd 18023000.usb: xHCI Host Controller [ 4.999010] xhci-hcd 18023000.usb: new USB bus registered, assigned bus number 4 [ 5.006452] xhci-hcd 18023000.usb: Host supports USB 3.0 SuperSpeed [ 5.014396] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 5.022916] hub 4-0:1.0: USB hub found [ 5.026784] hub 4-0:1.0: 1 port detected [ 5.033226] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.041660] init: - preinit - [ 6.157303] b53-srab-switch 18007000.ethernet-switch lan1: configuring for phy/gmii link mode [ 6.165978] bgmac_bcma bcma0:4 eth1: Link is Up - 1Gbps/Full - flow control off [ 6.173426] 8021q: adding VLAN 0 to HW filter on device lan1 [ 6.243829] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 10.401595] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 10.407404] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 615 [ 10.516421] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 10.524296] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 10.534241] UBIFS (ubi0:1): FS size: 115167232 bytes (109 MiB, 907 LEBs), journal size 5713920 bytes (5 MiB, 45 LEBs) [ 10.544874] UBIFS (ubi0:1): reserved for root: 4952683 bytes (4836 KiB) [ 10.551505] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID B7109B29-AC28-4600-85E5-8B049A9447C0, small LPT model [ 10.564080] mount_root: overlay filesystem has not been fully initialized yet [ 10.571622] mount_root: switching to ubifs overlay [ 10.835661] urandom-seed: Seed file not found (/etc/urandom.seed) [ 11.037397] procd: - early - [ 11.040401] procd: - watchdog - [ 11.581042] procd: - watchdog - [ 11.584444] procd: - ubus - [ 11.642182] procd: - init - [ 12.058250] urngd: v1.0.2 started. [ 13.083020] kmodloader: loading kernel modules from /etc/modules.d/* [ 13.145382] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace [ 13.152980] Backport generated by backports.git v5.15.33-1-0-g183c4ab2 [ 13.198688] PPP generic driver version 2.4.2 [ 13.204061] NET: Registered protocol family 24 [ 13.212712] usbcore: registered new interface driver brcmfmac [ 13.218685] pci 0000:00:00.0: enabling device (0140 -> 0142) [ 13.224411] brcmfmac 0000:01:00.0: enabling device (0140 -> 0142) [ 13.344032] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4366c-pcie for chip BCM43664/4 [ 13.352905] brcmfmac 0000:01:00.0: Direct firmware load for brcm/brcmfmac4366c-pcie.asus,rt-ac88u.bin failed with error -2 [ 13.576558] brcmfmac 0000:01:00.0: Direct firmware load for brcm/brcmfmac4366c-pcie.asus,rt-ac88u.txt failed with error -2 [ 13.587732] brcmfmac 0000:01:00.0: Direct firmware load for brcm/brcmfmac4366c-pcie.txt failed with error -2 [ 13.856552] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4366c-pcie for chip BCM43664/4 [ 13.865402] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available [ 13.876711] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43664/4 wl0: Nov 5 2018 03:19:56 version 10.28.2 (r769115) FWID 01-d2cbb8fd [ 13.899154] pci 0001:00:00.0: enabling device (0140 -> 0142) [ 13.904887] brcmfmac 0001:01:00.0: enabling device (0140 -> 0142) [ 14.024172] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4366c-pcie for chip BCM43664/4 [ 14.032989] brcmfmac 0001:01:00.0: Direct firmware load for brcm/brcmfmac4366c-pcie.asus,rt-ac88u.bin failed with error -2 [ 14.047886] brcmfmac 0001:01:00.0: Direct firmware load for brcm/brcmfmac4366c-pcie.asus,rt-ac88u.txt failed with error -2 [ 14.059067] brcmfmac 0001:01:00.0: Direct firmware load for brcm/brcmfmac4366c-pcie.txt failed with error -2 [ 14.336610] brcmfmac: brcmf_fw_alloc_request: using brcm/brcmfmac4366c-pcie for chip BCM43664/4 [ 14.345447] brcmfmac: brcmf_c_process_clm_blob: no clm_blob available (err=-2), device may have limited channels available [ 14.356744] brcmfmac: brcmf_c_preinit_dcmds: Firmware: BCM43664/4 wl0: Nov 5 2018 03:19:56 version 10.28.2 (r769115) FWID 01-d2cbb8fd [ 14.389188] kmodloader: done loading kernel modules from /etc/modules.d/* [ 19.834760] bgmac_bcma bcma0:4 eth1: Link is Up - 1Gbps/Full - flow control off [ 19.842141] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 19.850801] b53-srab-switch 18007000.ethernet-switch extsw: configuring for fixed/ link mode [ 19.859508] 8021q: adding VLAN 0 to HW filter on device extsw [ 19.869111] b53-srab-switch 18007000.ethernet-switch extsw: Link is Up - 1Gbps/Full - flow control off [ 19.924310] br0: port 1(extsw) entered blocking state [ 19.929403] br0: port 1(extsw) entered disabled state [ 19.935028] device extsw entered promiscuous mode [ 19.939775] device eth1 entered promiscuous mode [ 20.214973] br0: port 1(extsw) entered blocking state [ 20.220049] br0: port 1(extsw) entered forwarding state [ 20.244486] b53-srab-switch 18007000.ethernet-switch lan1: configuring for phy/gmii link mode [ 20.259759] 8021q: adding VLAN 0 to HW filter on device lan1 [ 20.324349] br0: port 2(lan1) entered blocking state [ 20.329387] br0: port 2(lan1) entered disabled state [ 20.334951] device lan1 entered promiscuous mode [ 20.606332] b53-srab-switch 18007000.ethernet-switch lan2: configuring for phy/gmii link mode [ 20.615277] 8021q: adding VLAN 0 to HW filter on device lan2 [ 20.674074] br0: port 3(lan2) entered blocking state [ 20.679061] br0: port 3(lan2) entered disabled state [ 20.684571] device lan2 entered promiscuous mode [ 20.863919] IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready [ 20.956439] b53-srab-switch 18007000.ethernet-switch lan3: configuring for phy/gmii link mode [ 20.965291] 8021q: adding VLAN 0 to HW filter on device lan3 [ 21.024164] br0: port 4(lan3) entered blocking state [ 21.029154] br0: port 4(lan3) entered disabled state [ 21.034711] device lan3 entered promiscuous mode [ 21.307715] b53-srab-switch 18007000.ethernet-switch lan4: configuring for phy/gmii link mode [ 21.316949] 8021q: adding VLAN 0 to HW filter on device lan4 [ 21.374158] br0: port 5(lan4) entered blocking state [ 21.379142] br0: port 5(lan4) entered disabled state [ 21.384774] device lan4 entered promiscuous mode [ 21.656204] b53-srab-switch 18007000.ethernet-switch wan: configuring for phy/gmii link mode [ 21.664960] 8021q: adding VLAN 0 to HW filter on device wan [ 21.671697] b53-srab-switch 18007000.ethernet-switch wan: Link is Up - 1Gbps/Full - flow control rx/tx [ 21.724622] br0: port 6(wan) entered blocking state [ 21.729531] br0: port 6(wan) entered disabled state [ 21.734950] device wan entered promiscuous mode [ 21.843803] br0: port 6(wan) entered blocking state [ 21.848706] br0: port 6(wan) entered forwarding state


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2022/06/12 11:52
  • by arinc9