ASUS Lyra (MAP-AC2200)

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

asus-lyra-map-ac2200-front.jpg

The Asus Lyra (MAP-AC2200) is a MU-MIMO Tri-Band WiFi router, which has one 2.4GHz and two 5GHz WiFi Interfaces, making it an interesting choice for wireless backhaul or repeater applications. The radios support MCS 0-9 (up through 256 QAM) for devices and paths that are compatible with those high-density modulations.

Note: The first 5 GHz radio (IPQ4019) is limited to ch. 36-64. The second 5 GHz radio (QCA9886), is limited to ch. 100-140. This is consistent with OEM firmware and is a result of the ART data and the data in the OEM firmware's cal data.

It has one 1G LAN port and one 1G WAN port, with six internal antennas.

The device is equipped with a Bluetooth chip. It is powered by an external 12V, 2A power adapter and supports DFS and 256QAM.

Install OpenWrt (generic explanation)

FIXME Please add the installation procedure here.

FIXME Find out flash layout, then add the flash layout table here (copy, paste, modify the example).

Please check out the article Flash layout. It contains examples and explanations that describe how to document the flash layout.

Note: Reset router to factory defaults if it has been previously configured. Installing OpenWrt on this device requires a two-step process, first writing the initramfs image from the OEM firmware - and then finalizing the installation by sysupgrading the real device firmware.

  1. Enable ssh in the OEM firmware (use port 22).
  2. Copy openwrt-ipq40xx-generic-asus_map-ac2200-initramfs-fit-uImage.itb via scp to /tmp/
  3. mtd-write -d linux -i /tmp/openwrt-ipq40xx-generic-asus_map-ac2200-initramfs-fit-uImage.itb
  4. reboot -f
  5. Now use the Ethernet port right beside the power connector.
  6. When booting, the LED will breathe in multiple colors, then blink blue, and when ready, will have a steady blue color.
  7. Wait for it to reboot. It will now have the IP 192.168.1.1, and the login will be root without a password.
  8. Copy openwrt-ipq40xx-generic-asus_map-ac2200-squashfs-sysupgrade.bin via scp to /tmp/
  9. sysupgrade -n /tmp/openwrt-ipq40xx-generic-asus_map-ac2200-squashfs-sysupgrade.bin
  10. Wait for it to reboot
  11. ssh to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

generic.flashing.tftp

The Asus MAP-AC2200 doesn't have a reliable push-button tftp recovery, as it can't deal with changed UBI partitioning (OEM and OpenWrt differ in this regard). Recovering the MAP-AC2200 requires opening the device and attaching a serial console to the unpopulated header “J35” (2mm spacing), the pinout is: 3.3v - RX - TX - GND (square is VCC).

Prepare your tftp server (192.168.1.70) and provide “asus_map-ac2200-initramfs-fit-uImage.itb” as “HIVESPOT.trx” to the MAP-AC2200.

Interrupt u-boot at the boot screen, pressing “1”, if you followed the default settings below, you can keep the defaults (press [ENTER]):

Please choose the operation: 
   1: Load System code to SDRAM via TFTP.
   2: Load System code then write to Flash via TFTP.
   3: Boot System code via Flash (default).
   4: Entr boot command line interface.
   7: Load Boot Loader code then write to Flash via Serial.
   9: Load Boot Loader code then write to Flash via TFTP.


You choosed 1


   1: Load System code to SDRAM via TFTP.
 Please Input new ones /or Ctrl-C to discard
	Input device IP (192.168.1.1) ==:

	Input server IP (192.168.1.70) ==:

	Input Linux Kernel filename (HIVESPOT.trx) ==:

Once the initramfs image has booted, sysupgrade can be used to install a known-working sysupgrade image of OpenWrt from the login shell provided on the serial console.

Specific values needed for tftp

Bootloader tftp client IPv4 address 192.168.1.1
Firmware tftp image Latest OpenWrt release (NOTE: Name must contain “asus_map-ac2200-initramfs-fit-uImage.itb”)
TFTP window start select “1: Load System code to SDRAM via TFTP.” manually over serial
TFTP client required IP address 192.168.1.70

generic.sysupgrade

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. The command line method for upgrading is:

  • sysupgrade

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, then enter the following commands:
cd /tmp
wget https://downloads.openwrt.org/snapshots/targets/ipq40xx/generic/openwrt-ipq40xx-generic-asus_map-ac2200-squashfs-sysupgrade.bin
sysupgrade /tmp/openwrt-ipq40xx-generic-asus_map-ac2200-squashfs-sysupgrade.bin

→ see “OEM easy installation”

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

FIXME Please fill in real values for this device, then remove the EXAMPLEs

The default network configuration is:

Interface Name Description Default configuration
br-lan EXAMPLE LAN & WiFi EXAMPLE 192.168.1.1/24
vlan0 (eth0.0) EXAMPLE LAN ports (1 to 4) EXAMPLE None
vlan1 (eth0.1) EXAMPLE WAN port EXAMPLE DHCP
wl0 EXAMPLE WiFi EXAMPLE Disabled

FIXME Please fill in real values for this device, then remove the EXAMPLEs

Numbers 0-3 are Ports 1-4 as labeled on the unit, number 4 is the Internet (WAN) on the unit, 5 is the internal connection to the router itself. Don't be fooled: Port 1 on the unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on.

Port Switch port
Internet (WAN) EXAMPLE 4
LAN 1 EXAMPLE 3

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

FIXME Please fill in real values for this device, then remove the EXAMPLEs

The Asus Lyra (MAP-AC2200) has the following buttons:

BUTTON Event
EXAMPLE Reset reset
EXAMPLE Secure Easy Setup ses
EXAMPLE No buttons at all. -

Front:
asus-lyra-map-ac2200-front-glow.jpg

Sides:
asus-lyra-map-ac2200-sides.jpg

Bottom label:

Note: This will void your warranty!

  • Peel off four (4) of the five (5) rubber feet (the one at the top may remain)
  • then remove four (4) Torx T10 screws.
  • Open the case with a spudger – there are latches spread around, but they probably won't break the first time you pop the lid off.

Main PCB:

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

Serial connection parameters
for Asus Lyra (MAP-AC2200)
115200, 8N1

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

None so far.

Booting Linux on physical CPU 0x0 Linux version 3.14.77 (jenkins@asuswrt-build-server) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Fri Nov 8 23:00:56 CST 2019 CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache Machine model: ASUS. MAP-AC2200 Memory policy: Data cache writealloc On node 0 totalpages: 65024 free_area_init_node: node 0, pgdat c07890c0, node_mem_map cfdfa000 Normal zone: 512 pages used for memmap Normal zone: 0 pages reserved Normal zone: 65024 pages, LIFO batch:15 PERCPU: Embedded 8 pages/cpu @cfdc8000 s8576 r8192 d16000 u32768 pcpu-alloc: s8576 r8192 d16000 u32768 alloc=8*4096 pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512 Kernel command line: root_rfs=0x0021b580 flash_type=nand ubi.mtd=UBI_DEV clk_ignore_unused PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 251232K/260096K available (4212K kernel code, 197K rwdata, 1184K rodata, 176K init, 537K bss, 8864K reserved, 0K highmem) Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0208000 - 0xc074d3bc (5397 kB) .init : 0xc074e000 - 0xc077a180 ( 177 kB) .data : 0xc077c000 - 0xc07ad420 ( 198 kB) .bss : 0xc07ad420 - 0xc0833930 ( 538 kB) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 _ Reboot message ... _______________________________________________________ >>> Emergency Sync complete >>> br0: port 4(ath2) entered disabled state >>> br0: port 3(ath1) entered disabled state >>> br0: port 2(ath0) entered disabled state >>> br0: port 1(eth1) entered disabled state >>> device eth1 left promiscuous mode >>> br0: port 1(eth1) entered disabled state >>> device ath0 left promiscuous mode >>> br0: port 2(ath0) entered disabled state >>> device ath1 left promiscuous mode >>> br0: port 3(ath1) entered disabled state >>> device ath2 left promiscuous mode >>> br0: port 4(ath2) entered disabled state >>> STOPPED EVENT for vap 0 (ce370000) >>> OL vap_start + >>> VDEV START >>> OL vap_start - >>> ol_vdev_start_resp_ev for vap 0 (ce370000) >>> su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 >>> send_vdev_up_cmd_non_tlv for vap 0 >>> Beacon mode set to staggered. Cannot enable FD >>> __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! >>> ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43 >>> STOPPED EVENT for vap 0 (ce370000) >>> [wifi0] FWLOG: [9236246] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 ) >>> [wifi0] FWLOG: [9236246] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x2 ) >>> [wifi0] FWLOG: [9236248] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) >>> [wifi0] FWLOG: [9236248] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) >>> [wifi0] FWLOG: [9236278] vap-0 VDEV_MGR_VDEV_START ( 0x985, 0x2, 0x0, 0x0 ) >>> [wifi0] FWLOG: [9236278] VDEV_MGR_VDEV_START_RESP ( 0x0 ) >>> [wifi0] FWLOG: [9236279] VDEV_MGR_HP_START_TIME ( 0x0, 0x985, 0x16f79001 ) >>> [wifi0] FWLOG: [9236279] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 ) >>> [wifi0] FWLOG: [9236279] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) >>> [wifi0] FWLOG: [9236279] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x985, 0x0, 0x0 ) >>> [wifi0] FWLOG: [9236462] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) >>> [wifi0] FWLOG: [9236462] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61d934 arg=cec184c0 >>> >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61d934 arg=cec184c0 >>> >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61df00 arg=cec184c0 >>> >>> send_vdev_delete_cmd_non_tlv for vap 0 >>> ol_ath_vap_delete: wmi_unified_vdev_delete_send done ID = 0 vap (cb1e0000) VAP Addr = 10:7b:44:XX:XX:XX: >>> ieee80211_mbo_vdetach: MBO terminated >>> ieee80211_oce_vdetach: OCE terminated >>> Suspending Target scn=cdec04c0 >>> waiting for target paused event from target >>> ol_ath_thermal_mitigation_detach: ++ >>> ol_ath_thermal_mitigation_detach: -- >>> ol_if_dfs_clist_update: called, cmd=1, nollist= (null), nentries=0 >>> ce_h2t_tx_ce_cleanup 1039 Fastpath mode ON, Cleaning up HTT Tx CEsmart_log_deinit: Smart logging Disabled >>> ol_tx_me_exit: Already Disabled !!! >>> Reset complete for wifi core id : 0 >>> hif_disable: Xhif_napi_destroy: NAPI 6 destroyed >>> hif_napi_destroy: no NAPI instances. Zapped.ath_sysfs_diag_fini: diag_fsattr >>> STOPPED EVENT for vap 0 (cd4ce000) >>> OL vap_start + >>> VDEV START >>> OL vap_start - >>> ol_vdev_start_resp_ev for vap 0 (cd4ce000) >>> ol_if_dfs_configure: called >>> ol_if_dfs_configure: ETSI domain >>> ol_if_dfs_disable: called >>> ol_if_dfs_enable: called >>> ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 >>> STOPPED EVENT for vap 0 (cd4ce000) >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61d934 arg=cb15a4c0 >>> >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61d934 arg=cb15a4c0 >>> >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61df00 arg=cb15a4c0 >>> >>> send_vdev_delete_cmd_non_tlv for vap 0 >>> ol_ath_vap_delete: wmi_unified_vdev_delete_send done ID = 0 vap (cdf28000) VAP Addr = 10:7b:44:XX:XX:XX: >>> ieee80211_mbo_vdetach: MBO terminated >>> ieee80211_oce_vdetach: OCE terminated >>> Suspending Target scn=cd2c04c0 >>> waiting for target paused event from target >>> ol_ath_thermal_mitigation_detach: ++ >>> ol_ath_thermal_mitigation_detach: -- >>> ol_if_dfs_clist_update: called, cmd=1, nollist= (null), nentries=0 >>> ce_h2t_tx_ce_cleanup 1039 Fastpath mode ON, Cleaning up HTT Tx CEsmart_log_deinit: Smart logging Disabled >>> ol_tx_me_exit: Already Disabled !!! >>> Reset complete for wifi core id : 1 >>> hif_disable: Xhif_napi_destroy: NAPI 6 destroyed >>> hif_napi_destroy: no NAPI instances. Zapped.ath_sysfs_diag_fini: diag_fsattr >>> channel is not 2.4G return faile. >>> STOPPED EVENT for vap 0 (ccb5c000) >>> OL vap_start + >>> VDEV START >>> OL vap_start - >>> ol_vdev_start_resp_ev for vap 0 (ccb5c000) >>> ol_if_dfs_configure: called >>> ol_if_dfs_configure: ETSI domain >>> ol_if_dfs_disable: called >>> ol_if_dfs_enable: called >>> ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 >>> STOPPED EVENT for vap 0 (ccb5c000) >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61d934 arg=cf3ea4c0 >>> >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61d934 arg=cf3ea4c0 >>> >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61df00 arg=cf3ea4c0 >>> >>> send_vdev_delete_cmd_non_tlv for vap 0 >>> ol_ath_vap_delete: wmi_unified_vdev_delete_send done ID = 0 vap (cb1d0000) VAP Addr = 10:7b:44:XX:XX:XX: >>> ieee80211_mbo_vdetach: MBO terminated >>> ieee80211_oce_vdetach: OCE terminated >>> Suspending Target scn=cc0c04c0 >>> waiting for target paused event from target >>> ol_ath_thermal_mitigation_detach: ++ >>> ol_ath_thermal_mitigation_detach: -- >>> ol_if_dfs_clist_update: called, cmd=1, nollist= (null), nentries=0 >>> ce_h2t_tx_ce_cleanup 1039 Fastpath mode ON, Cleaning up HTT Tx CEsmart_log_deinit: Smart logging Disabled >>> ol_tx_me_exit: Already Disabled !!! >>> hif_pci_device_reset: Reset Devicehif_pci_disable_bus: Xhif_disable: Xhif_napi_destroy: NAPI 6 destroyed >>> hif_napi_destroy: no NAPI instances. Zapped.ath_sysfs_diag_fini: diag_fsattr >>> channel is not 2.4G return faile. >>> osif_wrap_devt_detach:422 osif wrap dev table detached >>> osif_wrap_detach:475 osif wrap detached >>> ath_lowi_if_netlink_delete Going to decrement current LOWI netlink ref count: 3 >>> ol_if_dfs_teardown: called >>> ol_if_dfs_clist_update: called, cmd=1, nollist= (null), nentries=0 >>> ol_ath_phyerr_detach: called >>> channel is not 2.4G return faile. >>> ieee80211_bsteering_detach: Band steering terminated >>> ieee80211_ifdetach: ATF terminated >>> Green-AP : Green-AP : Detached >>> >>> Green-AP : Detached >>> ol_if_spectral_detach >>> SPECTRAL : Module removed (spectral = cc3dc000) >>> ol_ath_detach: remove global_ic[2]..gloabl_ic ptr:bf6a1df8 >>> ol_ath_detach: Peer Count 531 >>> ath_pci_remove >>> osif_wrap_devt_detach:422 osif wrap dev table detached >>> osif_wrap_detach:475 osif wrap detached >>> ath_lowi_if_netlink_delete Going to decrement current LOWI netlink ref count: 2 >>> ol_if_dfs_teardown: called >>> ol_if_dfs_clist_update: called, cmd=1, nollist= (null), nentries=0 >>> ol_ath_phyerr_detach: called >>> channel is not 2.4G return faile. >>> ieee80211_bsteering_detach: Band steering terminated >>> ieee80211_ifdetach: ATF terminated >>> Green-AP : Green-AP : Detached >>> >>> Green-AP : Detached >>> ol_if_spectral_detach >>> SPECTRAL : Module removed (spectral = cc30c000) >>> ol_ath_detach: remove global_ic[1]..gloabl_ic ptr:bf6a1df8 >>> ol_ath_detach: Peer Count 531 >>> ath_ahb_remove >>> ol_wifi_assoc_netlink_fini wifiassoc_nl is NULL >>> osif_wrap_devt_detach:422 osif wrap dev table detached >>> osif_wrap_detach:475 osif wrap detached >>> ath_lowi_if_netlink_delete Going to decrement current LOWI netlink ref count: 1 >>> ol_if_dfs_teardown: called >>> ol_if_dfs_clist_update: called, cmd=1, nollist= (null), nentries=0 >>> ol_ath_phyerr_detach: called >>> ieee80211_bsteering_detach: Band steering terminated >>> acfg_detach Netlink socket released >>> ieee80211_ifdetach: ATF terminated >>> Green-AP : Green-AP : Detached >>> >>> Green-AP : Detached >>> ol_if_spectral_detach >>> SPECTRAL : Module removed (spectral = cd29c000) >>> ol_ath_detach: remove global_ic[0]..gloabl_ic ptr:bf6a1df8 >>> ol_ath_detach: Peer Count 531 >>> ath_ahb_remove >>> Removing athdebug proc file >>> ath_dev: driver unloaded >>> ath_spectral: driver unloaded >>> ath_rate_atheros: driver unloaded >>> ath_tx99: driver unloaded >>> ath_hal: driver unloaded >>> ath_dfs: driver unloaded >>> ____________________________________________________________________________ Preemptible hierarchical RCU implementation. NR_IRQS:16 nr_irqs:16 16 Architected cp15 timer(s) running at 48.00MHz (virt). sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 2863311552512ns Switching to timer-based delay loop Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) CPU: Testing write buffer coherency: ok CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 Setting up static identity map for 0x802133c0 - 0x80213418 CPU1: Booted secondary processor CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 CPU2: Booted secondary processor CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 CPU3: Booted secondary processor CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 Brought up 4 CPUs SMP: Total of 4 processors activated (384.00 BogoMIPS). CPU: All CPU(s) started in SVC mode. VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 pinctrl core: initialized pinctrl subsystem regulator-dummy: no parameters NET: Registered protocol family 16 DMA: preallocated 2048 KiB pool for atomic coherent allocations cpuidle: using governor ladder cpuidle: using governor menu hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1 hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 3 hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 2 hw-breakpoint: CPU 3 failed to disable vector catch hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0 Version Rollback Feature Disabled gpiochip_add: registered GPIOs 0 to 69 on device: 1000000.pinctrl GPIO chip 1000000.pinctrl: created GPIO range 0->69 ==> 1000000.pinctrl PIN 0->69 i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2 sps:sps is ready. bio: create slab <bio-0> at 0 SD0 VccQ: 1800 <--> 3000 mV SCSI subsystem initialized msm_bus_fabric_init_driver msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus4096 ctx1 msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100 msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus1024 ctx1 Bluetooth: Core ver 2.18 NET: Registered protocol family 31 Bluetooth: HCI device and connection manager initialized Bluetooth: HCI socket layer initialized Bluetooth: L2CAP socket layer initialized Bluetooth: SCO socket layer initialized 80000.qcom,pcie supply vreg-3.3 not found, using dummy regulator 80000.qcom,pcie supply vreg-1.8 not found, using dummy regulator 80000.qcom,pcie supply vreg-0.9 not found, using dummy regulator 80000.qcom,pcie supply gdsc-vdd not found, using dummy regulator of_get_named_gpiod_flags exited with status 0 of_get_named_gpiod_flags exited with status 0 of_get_named_gpiod_flags exited with status 0 msm_pcie_enable: msm_pcie_enable: PCIe: trigger the reset of endpoint of RC0. msm_pcie_enable: msm_pcie_enable: PCIe RC0 PHY is ready! msm_pcie_enable: msm_pcie_enable: PCIe: Release the reset of endpoint of RC0. msm_pcie_enable: msm_pcie_enable: PCIe RC0 link initialized msm_pcie 80000.qcom,pcie: PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [io 0x40200000-0x402fffff] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] pci 0000:00:00.0: [17cb:1001] type 01 class 0x060400 msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0014[4] is all FFs pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit] pci 0000:00:00.0: PME# supported from D0 D3hot D3cold PCI: bus0: Fast back to back transfers disabled pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:01:00.0: [168c:0056] type 00 class 0x028000 msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 1:0x00 + 0x0014[4] is all FFs pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] pci 0000:01:00.0: PME# supported from D0 D3hot PCI: bus1: Fast back to back transfers disabled pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0028[4] is all FFs pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff 64bit] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff] msm_pcie_probe: msm_pcie_probe: RC0 is enabled in bootup Switched to clocksource arch_sys_counter NET: Registered protocol family 2 TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters available futex hash table entries: 1024 (order: 4, 65536 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 490 Key type asymmetric registered Asymmetric key parser 'x509' registered io scheduler noop registered io scheduler deadline registered (default) tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7 tcsr 1953000.ess_tcsr: setting ess interface select = 0 tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled ipq40xx-pinctrl 1000000.pinctrl: could not parse property pins msm_serial 78af000.serial: msm_serial: detected port #0 msm_serial 78af000.serial: uartclk = 1843200 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 139, base_baud = 115200) is a MSM msm_serial: console setup on port #0 console [ttyMSM0] enabled msm_serial: driver initialized msm_serial_hsl_init: driver initialized of_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]' of_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]' of_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]' of_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]' BLSP UART: Bus scaling is disabled. unregister_client_adhoc: Null cl handle passed unregister msm_serial_hs: probe of 78b0000.uart failed with error -2 msm_serial_hs module loaded of_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]' uart_tx_gpio is not available of_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]' uart_rx_gpio is not available of_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]' uart_cts_gpio is not available of_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]' uart_rfr_gpio is not available Wakeup irq not specified. BLSP UART: Bus scaling is disabled. sps: BAM device 0x07884000 is not registered yet. sps:BAM 0x07884000 is registered. 78b0000.uart: ttyQHS0 at MMIO 0x78b0000 (irq = 140, base_baud = 460800) is a MSM HS UART qca_serial_hs module loaded brd: module loaded sps: BAM device 0x07984000 is not registered yet. sps:BAM 0x07984000 is registered. msm_nand_bam_init: msm_nand_bam_init: BAM device registered: bam_handle 0xcf052600 sps:BAM 0x07984000 (va:0xd0a60000) enabled: ver:0x19, number of pipes:7 msm_nand_version_check: nand_major:1, nand_minor:4, qpic_major:1, qpic_minor:4 msm_nand_flash_onfi_probe: Found an ONFI compliant device MX30LF1G18AC msm_nand_scan: NAND Id: 0x9580f1c2 Buswidth: 8Bits Density: 128 MByte msm_nand_scan: pagesize: 2048 Erasesize: 131072 oobsize: 64 (in Bytes) msm_nand_scan: BCH ECC: 4 Bit msm_nand_scan: CFG0: 0x2a0408c0, CFG1: 0x0804745c RAWCFG0: 0x280420c0, RAWCFG1: 0x0005045d ECCBUFCFG: 0x00000203, ECCBCHCFG: 0x42040700 BAD BLOCK BYTE: 0x000001d1 2 ofpart partitions found on MTD device 7980000.qcom,nand Creating 2 MTD partitions on "7980000.qcom,nand": 0x000000000000-0x000000400000 : "Bootloader" 0x000000400000-0x000008000000 : "UBI_DEV" msm_nand_probe: NANDc phys addr 0x7980000, BAM phys addr 0x7984000, BAM IRQ 133 msm_nand_probe: Allocated DMA buffer at virt_addr 0xd0a7b000, phys_addr 0x8f058000 of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]' of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]' of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]' of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]' of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]' of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]' of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]' IMQ driver loaded successfully. (numdevs = 2, numqueues = 1) Hooking IMQ after NAT on PREROUTING. Hooking IMQ before NAT on POSTROUTING. of_get_named_gpiod_flags exited with status 0 phy_reset_gpio is 41 libphy: ipq40xx_mdio: probed ipq40xx-mdio 90000.mdio: ipq40xx-mdio driver was registered PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 i2c /dev entries driver requesting memory region failed of_get_named_gpiod_flags: can't parse gpios property of node '/soc/i2c@78b7000/lp55231@32[0]' lp5523x 0-0032: lp5523 Programmable led chip found nf_conntrack version 0.5.0 (3925 buckets, 15700 max) xt_time: kernel timezone is -0000 gre: GRE over IPv4 demultiplexor driver ip_tables: (C) 2000-2006 Netfilter Core Team arp_tables: (C) 2002 David S. Miller TCP: cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team NET: Registered protocol family 17 Bridge firewalling registered Bluetooth: RFCOMM TTY layer initialized Bluetooth: RFCOMM socket layer initialized Bluetooth: RFCOMM ver 1.11 Bluetooth: BNEP (Ethernet Emulation) ver 1.3 Bluetooth: BNEP filters: protocol multicast Bluetooth: BNEP socket layer initialized l2tp_core: L2TP core driver, V2.0 l2tp_ppp: PPPoL2TP kernel driver, V2.0 l2tp_netlink: L2TP netlink interface 8021q: 802.1Q VLAN Support v1.8 Registering SWP/SWPB emulation handler SD0 VccQ: disabling regulator-dummy: disabling UBI: attaching mtd1 to ubi0 UBI: scanning is finished UBI: attached mtd1 (name "UBI_DEV", size 124 MiB) to ubi0 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 991, bad PEBs: 1, corrupted PEBs: 0 UBI: user volume: 6, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 138/77, WL threshold: 4096, image sequence number: 2108563064 UBI: available PEBs: 20, total reserved PEBs: 971, PEBs reserved for bad PEB handling: 19 UBI: background thread "ubi_bgt0d" started, PID 74 gluebi_create: Hook read/write method of Factory. gluebi_create: Hook read/write method of Factory2. [Factory-0]: OK (ver: 41) [Factory2-0]: OK (ver: 41) Select [Factory-0] volume linux rfs_offset 21b580 mtd->size 3013000 Creating 1 MTD partitions on "linux": 0x00000021b580-0x000003013000 : "rootfs" mtd: device 6 (rootfs) set to be root filesystem volume linux2 rfs_offset 21b580 mtd->size 3013000 Creating 1 MTD partitions on "linux2": 0x00000021b580-0x000003013000 : "rootfs2" gluebi_create: skip jffs2 volume clk: Not disabling unused clocks VFS: Mounted root (squashfs filesystem) readonly on device 31:6. Freeing unused kernel memory: 176K (c074e000 - c077a000) offset 0x0 elapse 40ms found private data block and skip it nvram_commit(): pid 1 comm [init] found private data block and skip it ssdk_alloc_priv[4402]:INFO:ess-switch dts node number: 1 ssdk_dt_parse[2643]:INFO:ess-switch DT exist! ssdk_dt_parse[2672]:INFO:switch_access_mode: local bus ssdk_dt_parse_mac_mode[2271]:INFO:mac mode = 0x0 ssdk_dt_parse_mac_mode[2277]:INFO:mac mode1 doesn't exit! ssdk_dt_parse_mac_mode[2286]:INFO:mac mode2 doesn't exit! ssdk_dt_parse_uniphy[2305]:INFO:ess-uniphy DT doesn't exist! ssdk_dt_parse_scheduler_cfg[2495]:ERROR:cannot find port_scheduler_resource node ssdk_dt_parse_phy_info[2538]:INFO:qcom,port_phyinfo DT doesn't exist! ssdk_dt_parse_mdio[2575]:INFO:mdio DT exist! ssdk_dt_parse[2698]:INFO:switchreg_base_addr: 0xc000000 ssdk_dt_parse[2699]:INFO:switchreg_size: 0x80000 ssdk_dt_parse[2708]:INFO:ess-psgmii DT exist! ssdk_dt_parse[2765]:INFO:current dts led_source_num is 5 ssdk_plat_init start enable ess clk malibu_phy_api_ops_init[2505]:INFO:qca probe malibu phy driver succeeded! regi_init[4507]:INFO:Initializing DESS!! ssdk_switch_register[1588]:INFO:Chip version 0x1401 qca_link_polling_select[1282]:INFO:link-polling-required node does not exist ssdk_switch_register[1611]:INFO:polling is selected regi_init[4516]:INFO:Initializing DESS Done!! regi_init[4540]:INFO:qca-ssdk module init succeeded! QCA Hy-Fi multicast installation successfully mem_manager: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved ath_spectral: Version 2.0.0 Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reserved ath_hal: 0.9.17.1 (WRITE_EEPROM, 11D) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reserved ath_tx99: Version 2.0 Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved *********** IPQ4019 *************Wifi0 CPU frequency 250000000 hif_target_sync_ahb: Got FW signal, retries = 1hif_ahb_enable_bus: X - hif_type = 0xd, target_type = 0xbhif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4 hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON __ol_ath_attach() Allocated scn cdf804c0 __ol_ath_attach: dev name wifi0 ol_ath_attach interface_id 0 ol_target_init() BMI inited. ol_target_init() BMI Get Target Info. Chip id: 0xb, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined ol_transfer_bin_file[3815] Get Caldata for wifi0. qc98xx_verify_checksum: flash checksum passed: 0x4235 ol_transfer_bin_file 3881: Download Flash data len 12064 Board extended Data download address: 0x0 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version -1065183676 ath10k_ahb a000000.wifi: Direct firmware load failed with error 0 ath10k_ahb a000000.wifi: Falling back to user helper ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3678: downloading file 0, Download data len 4676 First OTP send param 8000 ol_ath_download_firmware :First OTP download and Execute is good address:0x5000 return param 4660 ol_ath_download_firmware:##Board Id 20 , CHIP Id 0 ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 wifi0: Selecting board data file name boardData_1_0_IPQ4019_DK04_2G.bin ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_2G.bin ath10k_ahb a000000.wifi: Direct firmware load failed with error 0 ath10k_ahb a000000.wifi: Falling back to user helper ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3678: downloading file 3, Download data len 12064 Board extended Data download address: 0x0 ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version -1065183676 ath10k_ahb a000000.wifi: Direct firmware load failed with error 0 ath10k_ahb a000000.wifi: Falling back to user helper ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3678: downloading file 0, Download data len 4676 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version -1065183676 ath10k_ahb a000000.wifi: Direct firmware load failed with error 0 ath10k_ahb a000000.wifi: Falling back to user helper ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath10k_ahb a000000.wifi: Direct firmware load failed with error 0 ath10k_ahb a000000.wifi: Falling back to user helper ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_swap_wlan_memory_expansion: length:185067 size_left:185087 dma_size_left:262144 fw_temp:d1b22004 fw_entry_size:185091 ol_swap_wlan_memory_expansion: dma_virt_addr :d1ae1000 fw_temp: d1b22008 length: 185067 Swap: bytes_left to copy: fw:16; dma_page:77077 ol_swap_wlan_memory_expansion: length:0 size_left:12 dma_size_left:77077 fw_temp:d1b4f2f7 fw_entry_size:185091 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 185067 Target address 4180b0 scn=cdf804c0 target_write_addr=4180b0 seg_info=cf219c10 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin ath10k_ahb a000000.wifi: Direct firmware load failed with error 0 ath10k_ahb a000000.wifi: Falling back to user helper ath10k_ahb a000000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3678: downloading file 1, Download data len 378664 ol_target_init() Download FW done. ERROR: No wifi_dump dts node available in the dts entry file ol_ath_attach() WMI attached. wmi_handle cf012000 wmi_unified_register_event_handler: Event id 62 is unavailable +htc_create .. HIF :ce3d0000-htc_create: (0xcf094800) htc_wmi_init() HT Create . cf094800 htc_wmi_init 7762 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 hif_enable_fastpath, Enabling fastpath mode +HWT hif_completion_thread_startup: pipe_num:0 pipe_info:0xce3d4578hif_completion_thread_startup: pipe_num:3 pipe_info:0xce3d4650hif_completion_thread_startup: pipe_num:4 pipe_info:0xce3d4698 -HWT Startup Mode-0 set <=== cfg max peer id 1056 ====> htt_peer_map_timer_init Enter pdev cd4b8000 hrtimer cd4bc948 htt_alloc_peer_map_mem : Alloc Success : host q vaddr cdc0c000 paddr 8dc0c000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from cd140000 Firmware_Build_Number:50 FW wireless modes: 0x680c num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339959b2 vht_supp_mcs:0x0000fffa btcoex_support 0, wlan_prio_gpio 0, coex_gpio_pin 0 0 0 wmi_service_coex_gpio 1, wmi_service_4_wire_coex_support 1, coex_version 0 Sending Ext resource cfg: HOST PLATFORM as 0 fw_feature_bitmap as 50 to TGT ol_ath_service_ready_event: tt_support: 1 ol_ath_service_ready_event: periodic_chan_stats: 1 ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 EXT NSS Supported idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 744 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 744, idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072, idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 6144, idx 6 req 5 num_units 0 num_unit_info 2 unit size 2052 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 531 unit_len 2052, Support not added yet for Service 91 Support not added yet for Service 92 No EXT_MSG send INIT now chunk 0 len 13568 requested , ptr 0x8dea0000 chunk 1 len 54272 requested , ptr 0x8d130000 chunk 2 len 217088 requested , ptr 0x8d1c0000 chunk 3 len 395064 requested , ptr 0x8d200000 chunk 4 len 107520 requested , ptr 0x8d1a0000 chunk 5 len 6144 requested , ptr 0x8dc40000 chunk 6 len 1089612 requested , ptr 0x8cc00000 chunk 7 len 0 requested , ptr 0x0 ol_ath_service_ready_event[4259] WAPI MBSSID 2 smart_log_init: Smart logging Enabled buf=ccd10000 (size=65536) Version = 16777216 3 status = 0 ol_ath_connect_htc() WMI is ready target uses HTT version 2.2; host uses 2.2 htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 0 ol_ath_attach() connect HTC. bypasswmi : 0 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100 ol_ath_phyerr_attach: called OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach: 3013: Netlink socket created:cf235000 ol_if_spectral_setup SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. ol_if_dfs_setup: called ol_if_dfs_attach: called; ptr=cd26998c, radar_info=ce31dbd8 dfs_attach: event log enabled by default ol_ath_rtt_meas_report_attach: called ol_ath_lowi_wmi_event_attach: called >>>> CB Set (null) ol_ath_attach() UMAC attach . BURSTING enabled by default ol_ath_attach: Set global_ic[1] ..ptr:bf6a1df8 ath_lowi_if_netlink_init LOWI Netlink successfully created osif_wrap_attach:444 osif wrap attached osif_wrap_devt_init:405 osif wrap dev table init done Wrap Attached: Wrap_com =cf233a00 ic->ic_wrap_com=cf233a00 &wrap_com->wc_devt=cf233a00 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- ol_ath_ahb_probe num_radios=0, wifi_radios[0].sc = cdf804c0 wifi_radio_type = 2 ath_sysfs_diag_init: diag_fsattr *********** IPQ4019 *************Wifi1 CPU frequency 250000000 hif_target_sync_ahb: Got FW signal, retries = 1hif_ahb_enable_bus: X - hif_type = 0xd, target_type = 0xbhif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4 hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON __ol_ath_attach() Allocated scn cd2804c0 __ol_ath_attach: dev name wifi1 ol_ath_attach interface_id 1 ol_target_init() BMI inited. ol_target_init() BMI Get Target Info. Chip id: 0xb, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined ol_transfer_bin_file[3815] Get Caldata for wifi1. qc98xx_verify_checksum: flash checksum passed: 0xaea5 ol_transfer_bin_file 3881: Download Flash data len 12064 Board extended Data download address: 0x0 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version -1065183676 ath10k_ahb a800000.wifi: Direct firmware load failed with error 0 ath10k_ahb a800000.wifi: Falling back to user helper ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3678: downloading file 0, Download data len 4676 First OTP send param 8000 ol_ath_download_firmware :First OTP download and Execute is good address:0x5400 return param 4660 ol_ath_download_firmware:##Board Id 21 , CHIP Id 0 ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 wifi1: Selecting board data file name boardData_1_0_IPQ4019_DK04_5G.bin ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_5G.bin ath10k_ahb a800000.wifi: Direct firmware load failed with error 0 ath10k_ahb a800000.wifi: Falling back to user helper ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3678: downloading file 3, Download data len 12064 Board extended Data download address: 0x0 ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version -1065183676 ath10k_ahb a800000.wifi: Direct firmware load failed with error 0 ath10k_ahb a800000.wifi: Falling back to user helper ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3678: downloading file 0, Download data len 4676 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version -1065183676 ath10k_ahb a800000.wifi: Direct firmware load failed with error 0 ath10k_ahb a800000.wifi: Falling back to user helper ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath10k_ahb a800000.wifi: Direct firmware load failed with error 0 ath10k_ahb a800000.wifi: Falling back to user helper ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_swap_wlan_memory_expansion: length:185067 size_left:185087 dma_size_left:262144 fw_temp:d1f1a004 fw_entry_size:185091 ol_swap_wlan_memory_expansion: dma_virt_addr :d1ed9000 fw_temp: d1f1a008 length: 185067 Swap: bytes_left to copy: fw:16; dma_page:77077 ol_swap_wlan_memory_expansion: length:0 size_left:12 dma_size_left:77077 fw_temp:d1f472f7 fw_entry_size:185091 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 185067 Target address 4180b0 scn=cd2804c0 target_write_addr=4180b0 seg_info=ccdf5510 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin [wifi0] FWLOG: [42957] WAL_DBGID_RST_STATS ( 0x1 ath10k_ahb a800000.wifi: Direct firmware load failed with error 0 ath10k_ahb a800000.wifi: Falling back to user helper , 0x1, 0x96c, 0x0 ) [wifi0] FWLOG: [42984] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi0] FWLOG: [42984] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12 ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfully ol_transfer_bin_file 3678: downloading file 1, Download data len 378664 , 0x1e, 0x94c, 0x94c, 0x0 ) [wifi0] FWLOG: [42984] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi0] FWLOG: [42984] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi0] FWLOG: [43093] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0xa10, 0x160, 0x0, 0x12 ) [wifi0] FWLOG: [43093] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0x0, 0x12, 0x10, 0x12 ) random: nonblocking pool is initialized ol_target_init() Download FW done. ERROR: No wifi_dump dts node available in the dts entry file ol_ath_attach() WMI attached. wmi_handle cd350000 wmi_unified_register_event_handler: Event id 62 is unavailable +htc_create .. HIF :cd2c0000-htc_create: (0xcf097000) htc_wmi_init() HT Create . cf097000 htc_wmi_init 7762 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 hif_enable_fastpath, Enabling fastpath mode +HWT hif_completion_thread_startup: pipe_num:0 pipe_info:0xcd2c4578hif_completion_thread_startup: pipe_num:3 pipe_info:0xcd2c4650hif_completion_thread_startup: pipe_num:4 pipe_info:0xcd2c4698 -HWT Startup Mode-0 set <=== cfg max peer id 1056 ====> htt_peer_map_timer_init Enter pdev ccab8000 hrtimer ccabc948 htt_alloc_peer_map_mem : Alloc Success : host q vaddr ccac2000 paddr 8cac2000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from cc740000 Firmware_Build_Number:50 FW wireless modes: 0x1f9001 num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339959b2 vht_supp_mcs:0x0000fffa wmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0 Sending Ext resource cfg: HOST PLATFORM as 0 fw_feature_bitmap as 50 to TGT ol_ath_service_ready_event: tt_support: 1 ol_ath_service_ready_event: periodic_chan_stats: 1 ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 EXT NSS Supported idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 744 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 744, idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072, idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 6144, idx 6 req 5 num_units 0 num_unit_info 2 unit size 2052 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 531 unit_len 2052, Support not added yet for Service 91 Support not added yet for Service 92 No EXT_MSG send INIT now chunk 0 len 13568 requested , ptr 0x8dc04000 chunk 1 len 54272 requested , ptr 0x8c730000 chunk 2 len 217088 requested , ptr 0x8c7c0000 chunk 3 len 395064 requested , ptr 0x8c000000 chunk 4 len 107520 requested , ptr 0x8c7a0000 chunk 5 len 6144 requested , ptr 0x8dc10000 chunk 6 len 1089612 requested , ptr 0x8c200000 chunk 7 len 0 requested , ptr 0x0 ol_ath_service_ready_event[4259] WAPI MBSSID 2 smart_log_init: Smart logging Enabled buf=cc310000 (size=65536) Version = 16777216 3 status = 0 ol_ath_connect_htc() WMI is ready htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 1 target uses HTT version 2.2; host uses 2.2 ol_ath_attach() connect HTC. bypasswmi : 0 ol_ath_attach: low_5ghz: 5490 high_5gh: 5850 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 ol_regdmn_init_channels: c 5180 out of range [5490..5850] ol_regdmn_init_channels: c 5200 out of range [5490..5850] ol_regdmn_init_channels: c 5220 out of range [5490..5850] ol_regdmn_init_channels: c 5240 out of range [5490..5850] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 ol_regdmn_init_channels: c 5180 out of range [5490..5850] ol_regdmn_init_channels: c 5200 out of range [5490..5850] ol_regdmn_init_channels: c 5220 out of range [5490..5850] ol_regdmn_init_channels: c 5240 out of range [5490..5850] ol_regdmn_init_channels: c 5180 out of range [5490..5850] ol_regdmn_init_channels: c 5220 out of range [5490..5850] ol_regdmn_init_channels: c 5200 out of range [5490..5850] ol_regdmn_init_channels: c 5240 out of range [5490..5850] ol_regdmn_init_channels: c 5180 out of range [5490..5850] ol_regdmn_init_channels: c 5200 out of range [5490..5850] ol_regdmn_init_channels: c 5220 out of range [5490..5850] ol_regdmn_init_channels: c 5240 out of range [5490..5850] ol_regdmn_init_channels: c 5180 out of range [5490..5850] ol_regdmn_init_channels: c 5220 out of range [5490..5850] ol_regdmn_init_channels: c 5200 out of range [5490..5850] ol_regdmn_init_channels: c 5240 out of range [5490..5850] Add VHT80 channel: 5210 Add VHT80 channel: 5775 ol_regdmn_init_channels: c 5180 out of range [5490..5850] ol_regdmn_init_channels: c 5200 out of range [5490..5850] ol_regdmn_init_channels: c 5220 out of range [5490..5850] ol_regdmn_init_channels: c 5240 out of range [5490..5850] Skipping VHT80 channel 5825 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100 ol_ath_phyerr_attach: called OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach: Offload using existing sock cf235000 ol_if_spectral_setup SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. ol_if_dfs_setup: called ol_if_dfs_attach: called; ptr=cc06998c, radar_info=ce31dbd8 dfs_attach: event log enabled by default ol_ath_rtt_meas_report_attach: called ol_ath_lowi_wmi_event_attach: called >>>> CB Set (null) ol_ath_attach() UMAC attach . BURSTING enabled by default ol_ath_attach: Set global_ic[2] ..ptr:bf6a1df8 ath_lowi_if_netlink_init Incremented LOWI netlink ref count: 2 osif_wrap_attach:444 osif wrap attached osif_wrap_devt_init:405 osif wrap dev table init done Wrap Attached: Wrap_com =ce94f400 ic->ic_wrap_com=ce94f400 &wrap_com->wc_devt=ce94f400 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- ol_ath_ahb_probe num_radios=1, wifi_radios[1].sc = cd2804c0 wifi_radio_type = 2 ath_sysfs_diag_init: diag_fsattr ath_ol_pci: (Atheros/multi-bss) hif_pci_enable_bus: con_mode = 0x0, device_id = 0x56PCI: enabling device 0000:00:00.0 (0144 -> 0147) PCI: enabling device 0000:01:00.0 (0140 -> 0142) hif_pci_enable_bus: hif_enable_pci done *********** QCA9888 *************hif_pci_enable_bus: hif_type = 0xe, target_type = 0xchif_pci_enable_bus: hif_pci_probe_tgt_wakeup donehif_target_sync: Loop checking FW signalhif_target_sync: Got FW signal, retries = 0hif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_set_hia_extnd: E chip_id 0xc chip_revision 0x0 CLOCK PLL skipped hif_set_hia_extnd: setting the target pll frac ffffffff intval ffffffff hif_set_hia_extnd: no frac provided, skipping pre-configuring PLL hif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_pci_configure_legacy_irq: Ehif_pci_configure_legacy_irq: X, ret = 0hif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4 hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON __ol_ath_attach() Allocated scn cc0c04c0 __ol_ath_attach: dev name wifi2 ol_ath_attach interface_id 2 ol_target_init() BMI inited. ol_target_init() BMI Get Target Info. Chip id: 0xc, chip version: 0x1000000 CE WAR Disabled NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file defined ol_transfer_bin_file[3815] Get Caldata for wifi2. qc98xx_verify_checksum: flash checksum passed: 0xe839 ol_transfer_bin_file 3881: Download Flash data len 12064 Board extended Data download address: 0x0 Board data initialized ol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version 0 ath_ol_pci 0000:01:00.0: Direct firmware load failed with error 0 ath_ol_pci 0000:01:00.0: Falling back to user helper ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3678: downloading file 0, Download data len 9116 First OTP send param 8000 Switching to Tx Mode-1 Threshold 280 [wifi1] FWLOG: [45349] WAL_DBGID_RST_STATS ( 0x1, 0x1, 0x1464, 0x0 ) [wifi1] FWLOG: [45390] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi1] FWLOG: [45390] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi1] FWLOG: [45390] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45 ol_ath_download_firmware :First OTP download and Execute is good address:0x4400 return param 4660 ol_ath_download_firmware:##Board Id 17 , CHIP Id 0 , 0x1e, 0x94c, 0x94c, 0x0 ) [wifi1] FWLOG: [45390] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 wifi2: Selecting board data file name boardData_2_0_QCA9888_5G_Y9484.bin ol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9888/hw.2/boardData_2_0_QCA9888_5G_Y9484.bin ath_ol_pci 0000:01:00.0: Direct firmware load failed with error 0 ath_ol_pci 0000:01:00.0: Falling back to user helper ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3678: downloading file 3, Download data len 12064 0x1e<6>Board extended Data download address: 0x0 , 0x94c, 0x94c, 0x0 ) [wifi1] FWLOG: [45492] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0xa10, 0x160, 0x10, 0x0 ) [wifi1] FWLOG: [45492] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0x10, 0x0, 0x10, 0x12 ) ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version 0 ath_ol_pci 0000:01:00.0: Direct firmware load failed with error 0 ath_ol_pci 0000:01:00.0: Falling back to user helper ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3678: downloading file 0, Download data len 9116 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version 0 ath_ol_pci 0000:01:00.0: Direct firmware load failed with error 0 ath_ol_pci 0000:01:00.0: Falling back to user helper ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath_ol_pci 0000:01:00.0: Direct firmware load failed with error 0 ath_ol_pci 0000:01:00.0: Falling back to user helper ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_swap_wlan_memory_expansion: length:261907 size_left:261927 dma_size_left:262144 fw_temp:d3201004 fw_entry_size:261931 ol_swap_wlan_memory_expansion: dma_virt_addr :d2fb6000 fw_temp: d3201008 length: 261907 Swap: bytes_left to copy: fw:16; dma_page:237 ol_swap_wlan_memory_expansion: length:0 size_left:12 dma_size_left:237 fw_temp:d3240f1f fw_entry_size:261931 Swap: wrong length read:0 ol_swap_wlan_memory_expansion: Swap total_bytes copied: 261907 Target address 41b0c8 scn=cc0c04c0 target_write_addr=41b0c8 seg_info=cc3fa510 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=QCA9888/hw.2/athwlan.bin swap_filename=/lib/firmware/QCA9888/hw.2/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: QCA9888/hw.2/athwlan.bin ath_ol_pci 0000:01:00.0: Direct firmware load failed with error 0 ath_ol_pci 0000:01:00.0: Falling back to user helper ath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfully ol_transfer_bin_file 3678: downloading file 1, Download data len 388448 Switching to Tx Mode-1 Threshold 280 ol_target_init() Download FW done. ERROR: No wifi_dump dts node available in the dts entry file ol_ath_attach() WMI attached. wmi_handle ccac6000 wmi_unified_register_event_handler: Event id 62 is unavailable +htc_create .. HIF :cc098000-htc_create: (0xcc091800) htc_wmi_init() HT Create . cc091800 htc_wmi_init 7762 host_enable 0 nss_nwifi_offload 0 ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0 hif_enable_fastpath, Enabling fastpath mode +HWT hif_completion_thread_startup: pipe_num:0 pipe_info:0xcc09c578hif_completion_thread_startup: pipe_num:3 pipe_info:0xcc09c650hif_completion_thread_startup: pipe_num:4 pipe_info:0xcc09c698 -HWT Startup Mode-0 set <=== cfg max peer id 1056 ====> htt_peer_map_timer_init Enter pdev cb880000 hrtimer cb884948 htt_alloc_peer_map_mem : Alloc Success : host q vaddr cb910000 paddr 8b910000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pkts ol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from cb500000 Firmware_Build_Number:50 FW wireless modes: 0x1f9001 num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339979b2 vht_supp_mcs:0x0000fffa wmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0 Sending Ext resource cfg: HOST PLATFORM as 0 fw_feature_bitmap as 50 to TGT ol_ath_service_ready_event: tt_support: 1 ol_ath_service_ready_event: periodic_chan_stats: 1 ol_ath_service_ready_event: sw_cal_support_check_flag: 1 Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17 EXT NSS Supported idx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256, idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024, idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096, idx 0 req 1 num_units 0 num_unit_info 2 unit size 896 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 896, idx 4 req 5 num_units 0 num_unit_info 2 unit size 2068 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 4 num_units 531 unit_len 2068, Support not added yet for Service 91 Support not added yet for Service 92 No EXT_MSG send INIT now chunk 0 len 13568 requested , ptr 0x8d3f8000 chunk 1 len 54272 requested , ptr 0x8b560000 chunk 2 len 217088 requested , ptr 0x8b580000 chunk 3 len 475776 requested , ptr 0x8b600000 chunk 4 len 1098108 requested , ptr 0x8b000000 chunk 5 len 0 requested , ptr 0x0 ol_ath_service_ready_event[4259] WAPI MBSSID 2 smart_log_init: Smart logging Enabled buf=cb110000 (size=65536) Version = 16777216 3 status = 0 ol_ath_connect_htc() WMI is ready htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 2 target uses HTT version 2.2; host uses 2.2 ol_ath_attach() connect HTC. bypasswmi : 0 ol_ath_attach: low_5ghz: 5150 high_5gh: 5330 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 ol_regdmn_init_channels: c 5745 out of range [5150..5330] ol_regdmn_init_channels: c 5765 out of range [5150..5330] ol_regdmn_init_channels: c 5785 out of range [5150..5330] ol_regdmn_init_channels: c 5805 out of range [5150..5330] ol_regdmn_init_channels: c 5825 out of range [5150..5330] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 ol_regdmn_init_channels: c 5745 out of range [5150..5330] ol_regdmn_init_channels: c 5765 out of range [5150..5330] ol_regdmn_init_channels: c 5785 out of range [5150..5330] ol_regdmn_init_channels: c 5805 out of range [5150..5330] ol_regdmn_init_channels: c 5825 out of range [5150..5330] ol_regdmn_init_channels: c 5745 out of range [5150..5330] ol_regdmn_init_channels: c 5785 out of range [5150..5330] ol_regdmn_init_channels: c 5765 out of range [5150..5330] ol_regdmn_init_channels: c 5805 out of range [5150..5330] ol_regdmn_init_channels: c 5745 out of range [5150..5330] ol_regdmn_init_channels: c 5765 out of range [5150..5330] ol_regdmn_init_channels: c 5785 out of range [5150..5330] ol_regdmn_init_channels: c 5805 out of range [5150..5330] ol_regdmn_init_channels: c 5825 out of range [5150..5330] ol_regdmn_init_channels: c 5745 out of range [5150..5330] ol_regdmn_init_channels: c 5785 out of range [5150..5330] ol_regdmn_init_channels: c 5765 out of range [5150..5330] ol_regdmn_init_channels: c 5805 out of range [5150..5330] Add VHT80 channel: 5210 Add VHT80 channel: 5775 ol_regdmn_init_channels: c 5745 out of range [5150..5330] ol_regdmn_init_channels: c 5765 out of range [5150..5330] ol_regdmn_init_channels: c 5785 out of range [5150..5330] ol_regdmn_init_channels: c 5805 out of range [5150..5330] ol_regdmn_init_channels: c 5825 out of range [5150..5330] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100 ol_ath_phyerr_attach: called OL Resmgr Init-ed ieee80211_bsteering_attach: Band steering initialized acfg_attach: Offload using existing sock cf235000 ol_if_spectral_setup SPECTRAL : get_capability not registered HAL_CAP_PHYDIAG : Capable SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237) SPECTRAL : get_capability not registered HAL_CAP_RADAR : Capable SPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242) SPECTRAL : get_capability not registered HAL_CAP_SPECTRAL_SCAN : Capable SPECTRAL : get_tsf64 not registered spectral_init_netlink 78 NULL SKB Green-AP : Green-AP : Attached Green-AP : Attached rate power table override is only supported for AR98XX ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. ol_if_dfs_setup: called ol_if_dfs_attach: called; ptr=cb1a198c, radar_info=ce31dbb0 dfs_attach: event log enabled by default ol_ath_rtt_meas_report_attach: called ol_ath_lowi_wmi_event_attach: called >>>> CB Set (null) ol_ath_attach() UMAC attach . BURSTING enabled by default ol_ath_attach: Set global_ic[3] ..ptr:bf6a1df8 ath_lowi_if_netlink_init Incremented LOWI netlink ref count: 3 osif_wrap_attach:444 osif wrap attached osif_wrap_devt_init:405 osif wrap dev table init done Wrap Attached: Wrap_com =cc7bc800 ic->ic_wrap_com=cc7bc800 &wrap_com->wc_devt=cc7bc800 __ol_ath_attach: needed_headroom reservation 60 ol_ath_thermal_mitigation_attach: -- ol_ath_pci_probe num_radios=2, wifi_radios[2].sc = cc0c04c0 wifi_radio_type = 2 ath_sysfs_diag_init: diag_fsattr isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100 isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 ol_regdmn_init_channels: c 5180 out of range [5490..5850] ol_regdmn_init_channels: c 5200 out of range [5490..5850] ol_regdmn_init_channels: c 5220 out of range [5490..5850] ol_regdmn_init_channels: c 5240 out of range [5490..5850] ol_regdmn_init_channels: c 5260 out of range [5490..5850] ol_regdmn_init_channels: c 5280 out of range [5490..5850] ol_regdmn_init_channels: c 5300 out of range [5490..5850] ol_regdmn_init_channels: c 5320 out of range [5490..5850] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 ol_regdmn_init_channels: c 5180 out of range [5490..5850] ol_regdmn_init_channels: c 5200 out of range [5490..5850] ol_regdmn_init_channels: c 5220 out of range [5490..5850] ol_regdmn_init_channels: c 5240 out of range [5490..5850] ol_regdmn_init_channels: c 5260 out of range [5490..5850] ol_regdmn_init_channels: c 5280 out of range [5490..5850] ol_regdmn_init_channels: c 5300 out of range [5490..5850] ol_regdmn_init_channels: c 5320 out of range [5490..5850] ol_regdmn_init_channels: c 5180 out of range [5490..5850] ol_regdmn_init_channels: c 5220 out of range [5490..5850] ol_regdmn_init_channels: c 5260 out of range [5490..5850] ol_regdmn_init_channels: c 5300 out of range [5490..5850] ol_regdmn_init_channels: c 5200 out of range [5490..5850] ol_regdmn_init_channels: c 5240 out of range [5490..5850] ol_regdmn_init_channels: c 5280 out of range [5490..5850] ol_regdmn_init_channels: c 5320 out of range [5490..5850] ol_regdmn_init_channels: c 5180 out of range [5490..5850] ol_regdmn_init_channels: c 5200 out of range [5490..5850] ol_regdmn_init_channels: c 5220 out of range [5490..5850] ol_regdmn_init_channels: c 5240 out of range [5490..5850] ol_regdmn_init_channels: c 5260 out of range [5490..5850] ol_regdmn_init_channels: c 5280 out of range [5490..5850] ol_regdmn_init_channels: c 5300 out of range [5490..5850] ol_regdmn_init_channels: c 5320 out of range [5490..5850] ol_regdmn_init_channels: c 5180 out of range [5490..5850] ol_regdmn_init_channels: c 5220 out of range [5490..5850] ol_regdmn_init_channels: c 5260 out of range [5490..5850] ol_regdmn_init_channels: c 5300 out of range [5490..5850] ol_regdmn_init_channels: c 5200 out of range [5490..5850] ol_regdmn_init_channels: c 5240 out of range [5490..5850] ol_regdmn_init_channels: c 5280 out of range [5490..5850] ol_regdmn_init_channels: c 5320 out of range [5490..5850] Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 ol_regdmn_init_channels: c 5180 out of range [5490..5850] ol_regdmn_init_channels: c 5200 out of range [5490..5850] ol_regdmn_init_channels: c 5220 out of range [5490..5850] ol_regdmn_init_channels: c 5240 out of range [5490..5850] ol_regdmn_init_channels: c 5260 out of range [5490..5850] ol_regdmn_init_channels: c 5280 out of range [5490..5850] ol_regdmn_init_channels: c 5300 out of range [5490..5850] ol_regdmn_init_channels: c 5320 out of range [5490..5850] Skipping VHT80 channel 5580 Skipping VHT80 channel 5660 Skipping VHT80 channel 5680 Skipping VHT80 channel 5700 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100 freq=106 isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 ol_regdmn_init_channels: c 5500 out of range [5150..5330] ol_regdmn_init_channels: c 5520 out of range [5150..5330] ol_regdmn_init_channels: c 5540 out of range [5150..5330] ol_regdmn_init_channels: c 5560 out of range [5150..5330] ol_regdmn_init_channels: c 5580 out of range [5150..5330] ol_regdmn_init_channels: c 5660 out of range [5150..5330] ol_regdmn_init_channels: c 5680 out of range [5150..5330] ol_regdmn_init_channels: c 5700 out of range [5150..5330] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 ol_regdmn_init_channels: c 5500 out of range [5150..5330] ol_regdmn_init_channels: c 5520 out of range [5150..5330] ol_regdmn_init_channels: c 5540 out of range [5150..5330] ol_regdmn_init_channels: c 5560 out of range [5150..5330] ol_regdmn_init_channels: c 5580 out of range [5150..5330] ol_regdmn_init_channels: c 5660 out of range [5150..5330] ol_regdmn_init_channels: c 5680 out of range [5150..5330] ol_regdmn_init_channels: c 5700 out of range [5150..5330] ol_regdmn_init_channels: c 5500 out of range [5150..5330] ol_regdmn_init_channels: c 5540 out of range [5150..5330] ol_regdmn_init_channels: c 5660 out of range [5150..5330] ol_regdmn_init_channels: c 5520 out of range [5150..5330] ol_regdmn_init_channels: c 5560 out of range [5150..5330] ol_regdmn_init_channels: c 5680 out of range [5150..5330] ol_regdmn_init_channels: c 5500 out of range [5150..5330] ol_regdmn_init_channels: c 5520 out of range [5150..5330] ol_regdmn_init_channels: c 5540 out of range [5150..5330] ol_regdmn_init_channels: c 5560 out of range [5150..5330] ol_regdmn_init_channels: c 5580 out of range [5150..5330] ol_regdmn_init_channels: c 5660 out of range [5150..5330] ol_regdmn_init_channels: c 5680 out of range [5150..5330] ol_regdmn_init_channels: c 5700 out of range [5150..5330] ol_regdmn_init_channels: c 5500 out of range [5150..5330] ol_regdmn_init_channels: c 5540 out of range [5150..5330] ol_regdmn_init_channels: c 5660 out of range [5150..5330] ol_regdmn_init_channels: c 5520 out of range [5150..5330] ol_regdmn_init_channels: c 5560 out of range [5150..5330] ol_regdmn_init_channels: c 5680 out of range [5150..5330] Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 ol_regdmn_init_channels: c 5500 out of range [5150..5330] ol_regdmn_init_channels: c 5520 out of range [5150..5330] ol_regdmn_init_channels: c 5540 out of range [5150..5330] ol_regdmn_init_channels: c 5560 out of range [5150..5330] ol_regdmn_init_channels: c 5580 out of range [5150..5330] ol_regdmn_init_channels: c 5660 out of range [5150..5330] ol_regdmn_init_channels: c 5680 out of range [5150..5330] ol_regdmn_init_channels: c 5700 out of range [5150..5330] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100 freq=58 isCountryCodeValid: EEPROM regdomain 0x0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150 ol_regdmn_init_channels: c 5500 out of range [5150..5330] ol_regdmn_init_channels: c 5520 out of range [5150..5330] ol_regdmn_init_channels: c 5540 out of range [5150..5330] ol_regdmn_init_channels: c 5560 out of range [5150..5330] ol_regdmn_init_channels: c 5580 out of range [5150..5330] ol_regdmn_init_channels: c 5660 out of range [5150..5330] ol_regdmn_init_channels: c 5680 out of range [5150..5330] ol_regdmn_init_channels: c 5700 out of range [5150..5330] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080 ol_regdmn_init_channels: c 5500 out of range [5150..5330] ol_regdmn_init_channels: c 5520 out of range [5150..5330] ol_regdmn_init_channels: c 5540 out of range [5150..5330] ol_regdmn_init_channels: c 5560 out of range [5150..5330] ol_regdmn_init_channels: c 5580 out of range [5150..5330] ol_regdmn_init_channels: c 5660 out of range [5150..5330] ol_regdmn_init_channels: c 5680 out of range [5150..5330] ol_regdmn_init_channels: c 5700 out of range [5150..5330] ol_regdmn_init_channels: c 5500 out of range [5150..5330] ol_regdmn_init_channels: c 5540 out of range [5150..5330] ol_regdmn_init_channels: c 5660 out of range [5150..5330] ol_regdmn_init_channels: c 5520 out of range [5150..5330] ol_regdmn_init_channels: c 5560 out of range [5150..5330] ol_regdmn_init_channels: c 5680 out of range [5150..5330] ol_regdmn_init_channels: c 5500 out of range [5150..5330] ol_regdmn_init_channels: c 5520 out of range [5150..5330] ol_regdmn_init_channels: c 5540 out of range [5150..5330] ol_regdmn_init_channels: c 5560 out of range [5150..5330] ol_regdmn_init_channels: c 5580 out of range [5150..5330] ol_regdmn_init_channels: c 5660 out of range [5150..5330] ol_regdmn_init_channels: c 5680 out of range [5150..5330] ol_regdmn_init_channels: c 5700 out of range [5150..5330] ol_regdmn_init_channels: c 5500 out of range [5150..5330] ol_regdmn_init_channels: c 5540 out of range [5150..5330] ol_regdmn_init_channels: c 5660 out of range [5150..5330] ol_regdmn_init_channels: c 5520 out of range [5150..5330] ol_regdmn_init_channels: c 5560 out of range [5150..5330] ol_regdmn_init_channels: c 5680 out of range [5150..5330] Add VHT80 channel: 5210 Add VHT80 channel: 5290 Add VHT80 channel: 5530 ol_regdmn_init_channels: c 5500 out of range [5150..5330] ol_regdmn_init_channels: c 5520 out of range [5150..5330] ol_regdmn_init_channels: c 5540 out of range [5150..5330] ol_regdmn_init_channels: c 5560 out of range [5150..5330] ol_regdmn_init_channels: c 5580 out of range [5150..5330] ol_regdmn_init_channels: c 5660 out of range [5150..5330] ol_regdmn_init_channels: c 5680 out of range [5150..5330] ol_regdmn_init_channels: c 5700 out of range [5150..5330] ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100 ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100 freq=58 [wifi2] FWLOG: [24124] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi2] FWLOG: [24124] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi2] FWLOG: [24124] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi2] FWLOG: [24124] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 ) [wifi2] FWLOG: [24124] WAL_DBGID_TX_AC_BUFFER_SET ( 0x100, 0x11e1a300 ) [wifi2] FWLOG: [24223] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0xa10, 0x160, 0x10, 0x0 ) [wifi2] FWLOG: [24223] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0x10, 0x0, 0x10, 0x12 ) [wifi2] FWLOG: [24665] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x199 [wifi0] FWLOG: [49413] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x199, 0x130, 0x0, 0x32 ) , 0x130, 0x30, 0x0 ) [wifi2] FWLOG: [24665] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x30, 0x0, 0x30, 0x0 ) [wifi2] FWLOG: [24741] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x199, 0x130, 0x30, 0x0 ) [wifi2] FWLOG: [24741] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x30, 0x0, 0x30, 0x0 ) [wifi1] FWLOG: [49499] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x199, 0x130, 0x30, 0x0 ) [wifi1] FWLOG: [49499] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x30, 0x0, 0x30, 0x0 ) wlan_vap_create : enter. devhandle=0xcdf804c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 10:7b:44:XX:XX:XX: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xcdf804c0, vap=0xcb1a8000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! Enabling TX checksum bit for the vap ath0 features 4000 Enabling SG bit for the vap ath0 features 4000 Enabling SG bit for the vap ath0 features 4000 Enabling TSO bit for the vap ath0 features 4000 Enabling LRO bit for the vap ath0 features 4000 VAP device ath0 created osifp: (cf3facc0) os_if: (cb1a8000) Switching to Tx Mode-1 Threshold 280 wlan_vap_create : enter. devhandle=0xcd2804c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 10:7b:44:XX:XX:XX: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xcd2804c0, vap=0xcb1b8000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! Enabling TX checksum bit for the vap ath1 features 4000 Enabling SG bit for the vap ath1 features 4000 Enabling SG bit for the vap ath1 features 4000 Enabling TSO bit for the vap ath1 features 4000 Enabling LRO bit for the vap ath1 features 4000 VAP device ath1 created osifp: (cf3fccc0) os_if: (cb1b8000) wlan_vap_create : enter. devhandle=0xcc0c04c0, opmode=IEEE80211_M_HOSTAP, flags=0x1 send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 10:7b:44:XX:XX:XX: ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xcc0c04c0, vap=0xcb5e8000, opmode=IEEE80211_M_HOSTAP, flags=0x1. __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! Enabling TX checksum bit for the vap ath2 features 4000 Enabling SG bit for the vap ath2 features 4000 Enabling SG bit for the vap ath2 features 4000 Enabling TSO bit for the vap ath2 features 4000 Enabling LRO bit for the vap ath2 features 4000 VAP device ath2 created osifp: (cf3fecc0) os_if: (cb5e8000) UBIFS: background thread "ubifs_bgt0_5" started, PID 390 UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 5, name "jffs2" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 17649664 bytes (16 MiB, 139 LEBs), journal size 2666496 bytes (2 MiB, 21 LEBs) UBIFS: reserved for root: 0 bytes (0 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID E92FXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX, small LPT model usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 xhci-hcd xhci-hcd.0.auto: ## USB3 port 0/1 addr(d3830430) s1(000002a0) --> (000002a0) xhci-hcd xhci-hcd.0.auto: irq 164, io mem 0x08a00000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd xhci-hcd.1.auto: xHCI Host Controller xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 xhci-hcd xhci-hcd.1.auto: irq 168, io mem 0x06000000 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd xhci-hcd.1.auto: xHCI Host Controller xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19) xhci-hcd xhci-hcd.1.auto: remove, state 4 usb usb4: USB disconnect, device number 1 xhci-hcd xhci-hcd.1.auto: Host not halted after 16000 microseconds. xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered xhci-hcd xhci-hcd.1.auto: remove, state 1 usb usb3: USB disconnect, device number 1 xhci-hcd xhci-hcd.1.auto: Host not halted after 16000 microseconds. xhci-hcd xhci-hcd.1.auto: Host controller not halted, aborting reset. xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered xhci-hcd xhci-hcd.0.auto: remove, state 1 usb usb2: USB disconnect, device number 1 xhci-hcd xhci-hcd.0.auto: Host not halted after 16000 microseconds. xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered xhci-hcd xhci-hcd.0.auto: remove, state 1 usb usb1: USB disconnect, device number 1 xhci-hcd xhci-hcd.0.auto: Host not halted after 16000 microseconds. xhci-hcd xhci-hcd.0.auto: Host controller not halted, aborting reset. xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 xhci-hcd xhci-hcd.0.auto: ## USB3 port 0/1 addr(d3860430) s1(000002a0) --> (000002a0) xhci-hcd xhci-hcd.0.auto: irq 164, io mem 0x08a00000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd xhci-hcd.1.auto: xHCI Host Controller xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 xhci-hcd xhci-hcd.1.auto: irq 168, io mem 0x06000000 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd xhci-hcd.1.auto: xHCI Host Controller xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19) usb 3-1: new full-speed USB device number 2 using xhci-hcd device eth1 entered promiscuous mode device ath0 entered promiscuous mode device ath1 entered promiscuous mode device ath2 entered promiscuous mode IPv6: ADDRCONF(NETDEV_UP): br0: link is not ready br0: port 1(eth1) entered listening state br0: port 1(eth1) entered listening state ol_wifi_assoc_netlink_receive: WiFi assoc/disassoc events being sent to PID:597 br0: port 1(eth1) entered learning state su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 [DEBUG] vap-0(ath0):set SIOC80211NWID, 4 characters DES SSID SET=lyra br0: port 2(ath0) entered listening state br0: port 2(ath0) entered listening state 8021q: adding VLAN 0 to HW filter on device ath0 [wifi0] FWLOG: [63703] WAL_DBGID_PDEV_INFO_PRINT ( 0x2, 0x0 ) [wifi0] FWLOG: [63777] WAL_DBGID_RST_STATS ( 0x6, 0x2, 0x96c, 0x0 ) [wifi0] FWLOG: [63777] WAL_DBGID_DEV_RESET ( 0xc01d, 0x3a5 ) [wifi0] FWLOG: [63829] WAL channel change freq=2412, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [64137] WAL channel change freq=2417, mode=1 flags=0 rx_ok=1 tx_ok=1 br0: topology change detected, propagating br0: port 1(eth1) entered forwarding state IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf5dce18 arg=ccd80000 osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xcb1a8000 br0: port 2(ath0) entered disabled state DEVICE IS DOWN ifname=ath0 DEVICE IS DOWN ifname=ath0 br0: port 2(ath0) entered listening state br0: port 2(ath0) entered listening state 8021q: adding VLAN 0 to HW filter on device ath0 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 [DEBUG] vap-0(ath1):set SIOC80211NWID, 9 characters DES SSID SET=lyra_5G-2 br0: port 3(ath1) entered listening state br0: port 3(ath1) entered listening state 8021q: adding VLAN 0 to HW filter on device ath1 ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf5dce18 arg=cc380000 osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xcb1b8000 br0: port 3(ath1) entered disabled state DEVICE IS DOWN ifname=ath1 DEVICE IS DOWN ifname=ath1 [wifi0] FWLOG: [64452] WAL channel change freq=2422, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [64502] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi0] FWLOG: [64502] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi0] FWLOG: [64779] WAL_DBGID_SECURITY_ENCR_EN ( ) [wifi0] FWLOG: [64779] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 ) [wifi0] FWLOG: [64806] WAL channel change freq=2412, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [65121] WAL channel change freq=2417, mode=1 flags=0 rx_ok=1 tx_ok=1 xhci-hcd xhci-hcd.1.auto: remove, state 4 usb usb4: USB disconnect, device number 1 xhci-hcd xhci-hcd.1.auto: Host not halted after 16000 microseconds. xhci-hcd xhci-hcd.1.auto: USB bus 4 deregistered xhci-hcd xhci-hcd.1.auto: remove, state 1 usb usb3: USB disconnect, device number 1 usb 3-1: USB disconnect, device number 2 br0: port 3(ath1) entered listening state br0: port 3(ath1) entered listening state 8021q: adding VLAN 0 to HW filter on device ath1 [wifi1] FWLOG: [64902] WAL_DBGID_PDEV_INFO_PRINT ( 0x2, 0x0 ) [wifi1] FWLOG: [64955] WAL_DBGID_RST_STATS ( 0x6, 0x2, 0x1464, su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 [wifi1] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 FWLOG: [64955] WAL_DBGID_DEV_RESET ( 0xc01d [DEBUG] vap-0(ath2):set SIOC80211NWID, 9 characters DES SSID SET=lyra_5G-1 , 0x3bc ) [wifi1] FWLOG: [65017] WAL channel change freq=5500, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [65127] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi1] FWLOG: [65127] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi1] FWLOG: [65445] WAL_DBGID_SECURITY_ENCR_EN ( ) [wifi1] FWLOG: [65445] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 ) br0: port 4(ath2) entered listening state br0: port 4(ath2) entered listening state 8021q: adding VLAN 0 to HW filter on device ath2 ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf5dce18 arg=cb180000 osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xcb5e8000 br0: port 4(ath2) entered disabled state DEVICE IS DOWN ifname=ath2 DEVICE IS DOWN ifname=ath2 br0: port 4(ath2) entered listening state br0: port 4(ath2) entered listening state 8021q: adding VLAN 0 to HW filter on device ath2 siwfreq Set freq vap 0 stop send + cb1a8000 [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf5dce18 arg=ccd80000 osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xcb1a8000 Set freq vap 0 stop send -cb1a8000 Set wait done --cb1a8000 [wifi2] FWLOG: [40694] WAL_DBGID_PDEV_INFO_PRINT ( 0x2, 0x0 ) [wifi2] FWLOG: [40744] WAL_DBGID_DEV_RESET ( 0xc01d, 0x43b ) [wifi2] FWLOG: [40804] WAL channel change freq=5180, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi2] FWLOG: [40914] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 siwfreq Set freq vap 0 stop send + cb5e8000 [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf5dce18 arg=cb180000 osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xcb5e8000 Set freq vap 0 stop send -cb5e8000 [wifi0] FWLOG: [65435] WAL channel change freq=2422, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [65750] WAL channel change freq=2427, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [66063] WAL channel change freq=2432, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [66145] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi0] FWLOG: [66145] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi0] FWLOG: [66210] WAL channel change freq=2412, mode=1 flags=0 rx_ok=1 tx_ok=1 Set wait done --cb5e8000 [wifi2] FWLOG: [40914] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi2] FWLOG: [41170] WAL_DBGID_SECURITY_ENCR_EN ( ) [wifi2] FWLOG: [41170] WAL_DBGID_SECURITY_MCAST_KEY_SET ( siwfreq Set freq vap 0 stop send + cb1b8000 [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf5dce18 arg=cc380000 osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xcb1b8000 Set freq vap 0 stop send -cb1b8000 0x1Set wait done --cb1b8000 [wifi1] FWLOG: [65787] WAL channel change freq=5520, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [66102] WAL channel change freq=5540, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [66316] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi1] FWLOG: [66316] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi1] FWLOG: [66374] WAL channel change freq=5500, mode=0 flags=0 rx_ok=1 tx_ok=1 br0: port 2(ath0) entered learning state [wifi2] FWLOG: [41336] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi2] FWLOG: [41336] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi2] FWLOG: [41685] WAL channel change freq=5200, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi2] FWLOG: [42000] WAL channel change freq=5220, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi2] FWLOG: [42314] WAL channel change freq=5240, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [66524] WAL channel change freq=2417, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [66839] WAL channel change freq=2422, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [67153] WAL channel change freq=2427, mode=1 flags=0 rx_ok=1 tx_ok=1 br0: port 3(ath1) entered learning state [wifi1] FWLOG: [66689] WAL channel change freq=5520, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [67004] WAL channel change freq=5540, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [67318] WAL channel change freq=5560, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [67633] WAL channel change freq=5580, mode=0 flags=0 rx_ok=1 tx_ok=1 br0: port 4(ath2) entered learning state [wifi2] FWLOG: [42628] WAL channel change freq=5260, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi2] FWLOG: [42942] WAL channel change freq=5280, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi2] FWLOG: [43256] WAL channel change freq=5300, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [67467] WAL channel change freq=2432, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [67781] WAL channel change freq=2437, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [68096] WAL channel change freq=2442, mode=1 flags=0 rx_ok=1 tx_ok=1 nf_conntrack_rtsp v0.7 loading nf_nat_rtsp v0.7 loading [wifi1] FWLOG: [67947] WAL channel change freq=5660, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [68261] WAL channel change freq=5680, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [68576] WAL channel change freq=5700, mode=0 flags=0 rx_ok=1 tx_ok=1 ---- ACS CALCULATE ---- Chan 52 pre_param 15 param 322 Chan 56 pre_param 11 param 318 Chan 60 pre_param 9 param 316 Chan 64 pre_param 7 param 314 Selected dot11 channel 60 OL vap_start + VDEV START OL vap_start - ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 ---- ACS CALCULATE ---- Chan 108 pre_param 119 param 119 Selected dot11 channel 108 OL vap_start + VDEV START OL vap_start - ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3 br0: topology change detected, propagating br0: port 2(ath0) entered forwarding state ol_vdev_start_resp_ev for vap 0 (ccac6000) send_wmm_update_cmd_non_tlv: ol_if_dfs_configure: called ol_if_dfs_configure: ETSI domain ol_if_dfs_disable: called ol_if_dfs_enable: called ol_vdev_start_resp_ev for vap 0 (cd350000) send_wmm_update_cmd_non_tlv: ol_if_dfs_configure: called ol_if_dfs_configure: ETSI domain ol_if_dfs_disable: called ol_if_dfs_enable: called [wifi2] FWLOG: [43571] WAL channel change freq=5320, mode=0 flags=0 rx_ok=1 tx_ok=1 [wifi2] FWLOG: [43884] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi2] FWLOG: [43884] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi2] FWLOG: [43902] vap-0 VDEV_MGR_VDEV_START ( 0x14b4, 0x2, 0x0, 0x1 ) [wifi2] FWLOG: [43903] WAL channel change freq=5300, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi2] [wifi0] FWLOG: [68409] WAL channel change freq=2447, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [68724] WAL channel change freq=2452, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [69038] WAL channel change freq=2457, mode=1 flags=0 rx_ok=1 tx_ok=1 FWLOG: [44111] VDEV_MGR_VDEV_START_RESP ( 0x0 ) br0: topology change detected, propagating br0: port 3(ath1) entered forwarding state [wifi1] FWLOG: [68890] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi1] FWLOG: [68890] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi1] FWLOG: [68898] vap-0 VDEV_MGR_VDEV_START ( 0x15a4, 0x2, 0x0, 0x1 ) [wifi1] FWLOG: [68898] WAL channel change freq=5540, mode=10 flags=0 rx_ok=1 tx_ok=1 [wifi1] FWLOG: [68898] WAL_DBGID_RST_STATS ( 0x2, 0x80, 0x15a4, 0x1 ) [wifi1] FWLOG: [69082] VDEV_MGR_VDEV_START_RESP ( 0x0 ) br0: topology change detected, propagating br0: port 4(ath2) entered forwarding state ---- ACS CALCULATE ---- Chan 6 pre_param 44 param 44 Chan 11 pre_param 40 param 40 Best Channel Selected 11 OL vap_start + VDEV START OL vap_start - ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43 xhci-hcd xhci-hcd.1.auto: Timeout while waiting for configure endpoint command xhci-hcd xhci-hcd.1.auto: Host not halted after 16000 microseconds. xhci-hcd xhci-hcd.1.auto: Host controller not halted, aborting reset. xhci-hcd xhci-hcd.1.auto: USB bus 3 deregistered xhci-hcd xhci-hcd.0.auto: remove, state 4 usb usb2: USB disconnect, device number 1 xhci-hcd xhci-hcd.0.auto: Host not halted after 16000 microseconds. xhci-hcd xhci-hcd.0.auto: USB bus 2 deregistered xhci-hcd xhci-hcd.0.auto: remove, state 4 usb usb1: USB disconnect, device number 1 ol_vdev_start_resp_ev for vap 0 (cf012000) send_wmm_update_cmd_non_tlv: su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1 send_vdev_up_cmd_non_tlv for vap 0 xhci-hcd xhci-hcd.0.auto: Host not halted after 16000 microseconds. xhci-hcd xhci-hcd.0.auto: Host controller not halted, aborting reset. xhci-hcd xhci-hcd.0.auto: USB bus 1 deregistered Beacon mode set to staggered. Cannot enable FD __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! [wifi0] FWLOG: [69352] WAL channel change freq=2462, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [69667] WAL channel change freq=2467, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [69981] WAL channel change freq=2472, mode=1 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [70294] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi0] FWLOG: [70294] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi0] FWLOG: [70305] vap-0 VDEV_MGR_VDEV_START ( 0x99e, 0x2, 0x0, 0x0 ) [wifi0] FWLOG: [70305] WAL channel change freq=2462, mode=7 flags=0 rx_ok=1 tx_ok=1 [wifi0] FWLOG: [70305] WAL_DBGID_RST_STATS ( 0x2, 0x80, 0x99e, 0x1 ) xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 xhci-hcd xhci-hcd.0.auto: ## USB3 port 0/1 addr(d3df0430) s1(000002a0) --> (000002a0) xhci-hcd xhci-hcd.0.auto: irq 164, io mem 0x08a00000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected xhci-hcd xhci-hcd.0.auto: xHCI Host Controller xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected xhci-hcd xhci-hcd.1.auto: xHCI Host Controller xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 xhci-hcd xhci-hcd.1.auto: irq 168, io mem 0x06000000 hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected xhci-hcd xhci-hcd.1.auto: xHCI Host Controller xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: config failed, hub doesn't have any ports! (err -19) usbcore: registered new interface driver btusb usbcore: registered new interface driver ath3k [wifi0] FWLOG: [70493] VDEV_MGR_VDEV_START_RESP ( 0x0 ) [wifi0] FWLOG: [70514] VDEV_MGR_HP_START_TIME ( 0x0, 0x99e, 0x19af000 ) [wifi0] FWLOG: [70514] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 ) [wifi0] FWLOG: [70514] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 ) [wifi0] FWLOG: [70514] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x99e, 0x0, 0x0 ) usb 3-1: new full-speed USB device number 2 using xhci-hcd usb 3-1: Direct firmware load failed with error 0 usb 3-1: Falling back to user helper usb 3-1: Firmware loaded from user helper succesfully usb 3-1: Direct firmware load failed with error 0 usb 3-1: Falling back to user helper usb 3-1: Firmware loaded from user helper succesfully usb 3-1: USB disconnect, device number 2 usb 3-1: new full-speed USB device number 3 using xhci-hcd usb 3-1: device descriptor read/64, error -110 xhci-hcd xhci-hcd.1.auto: Setup ERROR: setup context command for slot 1. usb 3-1: new full-speed USB device number 4 using xhci-hcd


Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00110 S - IMAGE_VARIANT_STRING=DAACANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x00000025 S - Reset status Config, 0x00000010 S - Core 0 Frequency, 0 MHz B - 261 - PBL, Start B - 1338 - bootable_media_detect_entry, Start B - 2608 - bootable_media_detect_success, Start B - 2622 - elf_loader_entry, Start B - 4028 - auth_hash_seg_entry, Start B - 6178 - auth_hash_seg_exit, Start B - 74217 - elf_segs_hash_verify_entry, Start B - 196008 - PBL, End B - 196032 - SBL1, Start B - 288049 - pm_device_init, Start D - 7 - pm_device_init, Delta B - 289540 - boot_flash_init, Start D - 74297 - boot_flash_init, Delta B - 368139 - boot_config_data_table_init, Start D - 13971 - boot_config_data_table_init, Delta - (419 Bytes) B - 384860 - clock_init, Start D - 7583 - clock_init, Delta B - 395878 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1 B - 399292 - sbl1_ddr_set_params, Start B - 404387 - cpr_init, Start D - 2 - cpr_init, Delta B - 408769 - Pre_DDR_clock_init, Start D - 4 - Pre_DDR_clock_init, Delta D - 13172 - sbl1_ddr_set_params, Delta B - 422074 - pm_driver_init, Start D - 2 - pm_driver_init, Delta B - 492044 - sbl1_wait_for_ddr_training, Start D - 28 - sbl1_wait_for_ddr_training, Delta B - 507587 - Image Load, Start D - 143910 - QSEE Image Loaded, Delta - (268920 Bytes) B - 651924 - Image Load, Start D - 2120 - SEC Image Loaded, Delta - (2048 Bytes) B - 662067 - Image Load, Start D - 198697 - APPSBL Image Loaded, Delta - (472859 Bytes) B - 861159 - QSEE Execution, Start D - 56 - QSEE Execution, Delta B - 867366 - SBL1, End D - 673444 - SBL1, Delta S - Flash Throughput, 2099 KB/s (744246 Bytes, 354446 us) S - DDR Frequency, 672 MHz U-Boot 2012.07-06585-ga52dc0d-dirty [local,local] (Mar 09 2017 - 11:28:27) HIVE bootloader version: 1.0.0.2 smem ram ptable found: ver: 1 len: 3 ASUS HIVE gpio init : wps / reset pin RAM Configuration: Bank #0: 80000000 256 MiB machid : 0x8010001 Maximum malloc length: 4096 KBytes mem_malloc_start/brk/end: 0x86ed0000/86ed0000/872f0000 Relocation offset: 0 NAND: ID = 9580f1c2 Vendor = c2 Device = f1 ONFI device found SF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ff ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 128 MiB *** Warning - bad CRC, using default environment PCI0 Link Intialized In: serial Out: serial Err: serial Check bootloader area ... name : offset size 0:SBL1 : 00000000 00080000 0:MIBIB : 00080000 00080000 0:QSEE : 00100000 00100000 0:CDT : 00200000 00080000 0:APPSBL : 00280000 00140000 0:APPSBLENV : 003c0000 00040000 machid: 8010001 flash_type: 2 Set ENGX pattern failed !! LP5523 Chip addresses: 32 Creating 1 MTD partitions on "nand0": 0x00400000-0x08000000 : "mtd=2" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: max. sequence number: 78095 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=2" UBI: MTD device size: 124 MiB UBI: number of good PEBs: 991 UBI: number of bad PEBs: 1 UBI: number of corrupted PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 8 UBI: available PEBs: 10 UBI: total number of reserved PEBs: 981 UBI: number of PEBs reserved for bad PEB handling: 9 UBI: max/mean erase counter: 169/79 UBI: image sequence number: 2108563064 UBI: vol_id reserved_pebs alignment data_pad vol_type usable_leb_size used_ebs used_bytes last_eb_bytes corrupted upd_marker name_len name UBI: 0 3 1 0 dynamic 1f000 3 5d000 1f000 0 0 5 nvram UBI: 1 1 1 0 dynamic 1f000 1 1f000 1f000 0 0 7 Factory UBI: 2 1 1 0 dynamic 1f000 1 1f000 1f000 0 0 8 Factory2 UBI: 3 17 1 0 dynamic 1f000 17 2c9000 1f000 0 0 5 linux UBI: 4 18d 1 0 dynamic 1f000 18d 3013000 1f000 0 0 6 linux2 UBI: 5 95 1 0 dynamic 1f000 95 120b000 1f000 0 0 5 jffs2 UBI: 6 54 1 0 dynamic 1f000 54 a2c000 1f000 0 0 6 rootfs UBI: 7 136 1 0 dynamic 1f000 136 258a000 1f000 0 0 b rootfs_data UBI: 7fffefff 2 1 0 dynamic 1f000 2 3e000 2 0 0 d layout volume UBI volume [linux] size 2c9000 smaller than 3013000! Read 0x1f000 bytes from volume [Factory] offset 0x0 to 86eb0ce0 EEPROM set 0: OK (version 41) Read 0x1f000 bytes from volume [Factory2] offset 0x0 to 86eb0ce0 EEPROM set 1: OK (version 41) Read 0x1f000 bytes from volume [Factory] offset 0x0 to 86ed1850 Select EEPROM set 0 at offset 0x0. Please choose the operation: 1: Load System code to SDRAM via TFTP. 2: Load System code then write to Flash via TFTP. 3: Boot System code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP.  1  0 3: Boot System code via Flash (default). HIVE bootloader version: 1.0.0.2 MAC Address: 10:7B:44:XX:XX:X0 Read 0x40 bytes from volume [linux] offset 0x0 to 84000000 FIT/FDT format image found at 0x84000000, size 0x002afd84 Read 0x2afdc4 bytes from volume [linux] offset 0x0 to 84000000 ## Booting kernel from FIT Image at 84000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM OpenWrt Linux-4.14.167 Type: Kernel Image Compression: lzma compressed Data Start: 0x840000e4 Data Size: 2797824 Bytes = 2.7 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: a1ff5169 Hash algo: sha1 Hash value: 69edcdce8ecfb5129717f04ac07450b0f811a079 ## Flattened Device Tree from FIT Image at 84000000 Using 'config@1' configuration Trying 'fdt@1' FDT blob subimage Description: ARM OpenWrt asus_map-ac2200 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x842ab320 Data Size: 17777 Bytes = 17.4 KiB Architecture: ARM Hash algo: crc32 Hash value: 518a6ab0 Hash algo: sha1 Hash value: c9d463f04aebef3435401e0e1efac2e3e47afc26 Booting using the fdt blob at 0x842ab320 Read 0x28 bytes from volume [linux2] offset 0x0 to 86ecfc38 Copy firmware from c049b000 to c34ae000, length 2afdc4 0x2afdc4 bytes written to volume linux2 Uncompressing Kernel Image ... OK Loading Device Tree to 86ec8000, end 86ecf570 ... OK Device nand2 not found! Using machid 0x8010001 from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.14.167 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10911-c155900f66)) #0 SMP Wed Jan 29 16:05:35 2020 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: ASUS Lyra MAP-AC2200 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 65024 [ 0.000000] free_area_init_node: node 0, pgdat c0a24280, node_mem_map cfdf9000 [ 0.000000] Normal zone: 512 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 65024 pages, LIFO batch:15 [ 0.000000] random: get_random_bytes called from 0xc09008d0 with crng_init=0 [ 0.000000] percpu: Embedded 15 pages/cpu s29388 r8192 d23860 u61440 [ 0.000000] pcpu-alloc: s29388 r8192 d23860 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64512 [ 0.000000] Kernel command line: root_rfs=0x00000000 flash_type=nand [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Memory: 249928K/260096K available (4452K kernel code, 146K rwdata, 688K rodata, 1024K init, 236K bss, 10168K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB) [ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB) [ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0208000 - 0xc0759318 (5445 kB) [ 0.000000] .init : 0xc0900000 - 0xc0a00000 (1024 kB) [ 0.000000] .data : 0xc0a00000 - 0xc0a24b80 ( 147 kB) [ 0.000000] .bss : 0xc0a26000 - 0xc0a61018 ( 237 kB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns [ 0.000007] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns [ 0.000021] Switching to timer-based delay loop, resolution 20ns [ 0.000243] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000) [ 0.000261] pid_max: default: 32768 minimum: 301 [ 0.000394] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000412] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.001001] CPU: Testing write buffer coherency: ok [ 0.001670] Setting up static identity map for 0x80300000 - 0x80300060 [ 0.001810] Hierarchical SRCU implementation. [ 0.002457] smp: Bringing up secondary CPUs ... [ 0.005139] smp: Brought up 1 node, 4 CPUs [ 0.005156] SMP: Total of 4 processors activated (384.00 BogoMIPS). [ 0.005164] CPU: All CPU(s) started in SVC mode. [ 0.009140] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.009290] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.009313] futex hash table entries: 1024 (order: 4, 65536 bytes) [ 0.009492] pinctrl core: initialized pinctrl subsystem [ 0.010405] NET: Registered protocol family 16 [ 0.010688] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.011684] cpuidle: using governor ladder [ 0.011727] cpuidle: using governor menu [ 0.028703] usbcore: registered new interface driver usbfs [ 0.028765] usbcore: registered new interface driver hub [ 0.028841] usbcore: registered new device driver usb [ 0.028887] pps_core: LinuxPPS API ver. 1 registered [ 0.028896] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.028920] PTP clock support registered [ 0.030135] clocksource: Switched to clocksource arch_sys_counter [ 0.030958] NET: Registered protocol family 2 [ 0.031627] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.031670] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.031719] TCP: Hash tables configured (established 2048 bind 2048) [ 0.031826] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.031860] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.032045] NET: Registered protocol family 1 [ 0.032090] PCI: CLS 0 bytes, default 64 [ 0.033025] No memory allocated for crashlog [ 0.033203] workingset: timestamp_bits=30 max_order=16 bucket_order=0 [ 0.036549] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.036563] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.041808] io scheduler noop registered [ 0.041827] io scheduler deadline registered (default) [ 0.043230] OF: PCI: host bridge /soc/pci@40000000 ranges: [ 0.043265] OF: PCI: IO 0x40200000..0x402fffff -> 0x40200000 [ 0.043282] OF: PCI: MEM 0x40300000..0x40ffffff -> 0x40300000 [ 0.260125] qcom-pcie 40000000.pci: link up [ 0.260276] qcom-pcie 40000000.pci: PCI host bridge to bus 0000:00 [ 0.260296] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.260312] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0x40200000-0x402fffff]) [ 0.260326] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff] [ 0.260368] pci 0000:00:00.0: [17cb:1001] type 01 class 0x060400 [ 0.260404] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit] [ 0.260462] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.260657] PCI: bus0: Fast back to back transfers disabled [ 0.260870] pci 0000:01:00.0: [168c:0056] type 00 class 0x028000 [ 0.261078] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.261742] pci 0000:01:00.0: PME# supported from D0 D3hot [ 0.262028] PCI: bus1: Fast back to back transfers disabled [ 0.262080] pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff] [ 0.262097] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff 64bit] [ 0.262121] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit] [ 0.262197] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.262213] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff] [ 0.262944] pcieport 0000:00:00.0: AER enabled with IRQ 94 [ 0.264380] bam-dma-engine 8e04000.dma: num-channels unspecified in dt [ 0.264396] bam-dma-engine 8e04000.dma: num-ees unspecified in dt [ 0.265600] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000 [ 0.265689] tcsr 1953000.ess_tcsr: setting ess interface select = 0 [ 0.265764] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222 [ 0.265991] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.267723] msm_serial 78af000.serial: msm_serial: detected port #0 [ 0.267769] msm_serial 78af000.serial: uartclk = 1843200 [ 0.267821] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 25, base_baud = 115200) is a MSM [ 0.267848] msm_serial: console setup on port #0 [ 0.868129] console [ttyMSM0] enabled [ 0.873013] msm_serial: driver initialized [ 0.880444] loop: module loaded [ 0.881971] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 0.883373] nand: Macronix MX30LF1G18AC [ 0.889969] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.893639] 7 fixed-partitions partitions found on MTD device qcom_nand.0 [ 0.901189] Creating 7 MTD partitions on "qcom_nand.0": [ 0.908032] 0x000000000000-0x000000080000 : "SBL1" [ 0.914114] 0x000000080000-0x000000100000 : "MIBIB" [ 0.918894] 0x000000100000-0x000000200000 : "QSEE" [ 0.924060] 0x000000200000-0x000000280000 : "CDT" [ 0.928486] 0x000000280000-0x0000003c0000 : "APPSBL" [ 0.933886] 0x0000003c0000-0x000000400000 : "APPSBLENV" [ 0.938105] 0x000000400000-0x000008000000 : "ubi" [ 0.951087] random: fast init done [ 1.035399] libphy: ipq40xx_mdio: probed [ 1.066132] ESS reset ok! [ 1.099109] ESS reset ok! [ 1.364121] PHY 3 single test PSGMII issue happen! [ 1.506710] PHY3 test see issue! [ 1.534776] ESS reset ok! [ 1.960494] libphy: Fixed MDIO Bus: probed [ 1.961377] EDMA using MAC@ - using [ 1.961391] 92:46:9c:XX:XX:XX [ 1.967562] EDMA using MAC@ - using [ 1.967573] 5e:c8:13:XX:XX:XX [ 2.071090] i2c /dev entries driver [ 2.071348] i2c_qup 78b7000.i2c: using default clock-frequency 100000 [ 2.200570] lp5523x 0-0032: lp5523 Programmable led chip found [ 2.225291] NET: Registered protocol family 10 [ 2.227178] Segment Routing with IPv6 [ 2.228735] NET: Registered protocol family 17 [ 2.232482] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 2.237092] 8021q: 802.1Q VLAN Support v1.8 [ 2.249965] Registering SWP/SWPB emulation handler [ 2.258298] UBI: auto-attach mtd6 [ 2.258585] ubi0: attaching mtd6 [ 2.821444] random: crng init done [ 2.860717] ubi0: scanning is finished [ 2.868810] ubi0: attached mtd6 (name "ubi", size 124 MiB) [ 2.868843] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 2.873234] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 2.880050] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 2.886925] ubi0: good PEBs: 991, bad PEBs: 1, corrupted PEBs: 0 [ 2.893691] ubi0: user volume: 8, internal volumes: 1, max. volumes count: 128 [ 2.899933] ubi0: max/mean erase counter: 144/77, WL threshold: 4096, image sequence number: 2108563064 [ 2.906979] ubi0: available PEBs: 0, total reserved PEBs: 991, PEBs reserved for bad PEB handling: 19 [ 2.916282] ubi0: background thread "ubi_bgt0d" started, PID 85 [ 2.917239] block ubiblock0_6: created from ubi0:6(rootfs) [ 2.931368] ubiblock: device ubiblock0_6 (rootfs) set to be root filesystem [ 2.936913] hctosys: unable to open rtc device (rtc0) [ 2.948593] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 2.950234] Freeing unused kernel memory: 1024K [ 3.379615] init: Console is alive [ 3.379836] init: - watchdog - [ 4.106459] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.363111] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 4.363174] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 4.367729] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x0000000002010010 [ 4.375156] xhci-hcd xhci-hcd.0.auto: irq 129, io mem 0x06000000 [ 4.385118] hub 1-0:1.0: USB hub found [ 4.390753] hub 1-0:1.0: 1 port detected [ 4.394530] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 4.398322] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 4.403660] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 4.412272] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 4.418293] hub 2-0:1.0: USB hub found [ 4.426159] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19) [ 4.430983] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.452055] init: - preinit - [ 4.760164] usb 1-1: new full-speed USB device number 2 using xhci-hcd [ 5.415017] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 5.416292] ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=100 [ 5.419769] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 8.683184] UBIFS (ubi0:7): default file-system created [ 8.683903] UBIFS (ubi0:7): background thread "ubifs_bgt0_7" started, PID 198 [ 8.737246] UBIFS (ubi0:7): UBIFS: mounted UBI device 0, volume 7, name "rootfs_data" [ 8.737284] UBIFS (ubi0:7): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 8.744100] UBIFS (ubi0:7): FS size: 45457408 bytes (43 MiB, 358 LEBs), journal size 2285568 bytes (2 MiB, 18 LEBs) [ 8.753979] UBIFS (ubi0:7): reserved for root: 2147065 bytes (2096 KiB) [ 8.764211] UBIFS (ubi0:7): media format: w4/r0 (latest is w5/r0), UUID 7C6EXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX, small LPT model [ 8.772497] mount_root: overlay filesystem has not been fully initialized yet [ 8.782670] mount_root: switching to ubifs overlay [ 8.804158] urandom-seed: Seed file not found (/etc/urandom.seed) [ 8.875324] procd: - early - [ 8.875427] procd: - watchdog - [ 9.671252] procd: - watchdog - [ 9.674148] procd: - ubus - [ 9.821384] procd: - init - [ 10.267489] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.274415] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 10.283392] hidraw: raw HID events driver (C) Jiri Kosina [ 10.290463] Bluetooth: Core ver 2.22 [ 10.290559] NET: Registered protocol family 31 [ 10.293103] Bluetooth: HCI device and connection manager initialized [ 10.297371] Bluetooth: HCI socket layer initialized [ 10.303641] urngd: v1.0.2 started. [ 10.303942] Bluetooth: L2CAP socket layer initialized [ 10.311992] Bluetooth: SCO socket layer initialized [ 10.318473] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 [ 10.321791] Bluetooth: BNEP filters: protocol multicast [ 10.327322] Bluetooth: BNEP socket layer initialized [ 10.334873] usbcore: registered new interface driver btusb [ 10.338327] Loading modules backported from Linux version v4.19.98-0-gd183c8e2647a [ 10.342865] Backport generated by backports.git v4.19.98-1-0-g8204eb99 [ 10.352610] Bluetooth: HCI UART driver ver 2.3 [ 10.356822] Bluetooth: HCI UART protocol H4 registered [ 10.361300] Bluetooth: HCI UART protocol BCSP registered [ 10.366368] Bluetooth: HCI UART protocol ATH3K registered [ 10.372961] Bluetooth: HIDP (Human Interface Emulation) ver 1.2 [ 10.377229] Bluetooth: HIDP socket layer initialized [ 10.385036] ip_tables: (C) 2000-2006 Netfilter Core Team [ 10.393348] nf_conntrack version 0.5.0 (4096 buckets, 16384 max) [ 10.414862] Bluetooth: RFCOMM TTY layer initialized [ 10.414910] Bluetooth: RFCOMM socket layer initialized [ 10.418644] Bluetooth: RFCOMM ver 1.11 [ 10.434119] xt_time: kernel timezone is -0000 [ 10.434897] usbcore: registered new interface driver ath3k [ 10.464700] PPP generic driver version 2.4.2 [ 10.465664] NET: Registered protocol family 24 [ 10.479305] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x56. [ 10.480093] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 10.486727] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 10.671786] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:01:00.0.txt failed with error -2 [ 10.671828] ath10k_pci 0000:01:00.0: Falling back to user helper [ 10.750826] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed [ 10.751198] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2 [ 10.758698] ath10k_pci 0000:01:00.0: Falling back to user helper [ 10.912123] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/ct-firmware-5.bin failed with error -2 [ 10.912176] ath10k_pci 0000:01:00.0: Falling back to user helper [ 10.983813] firmware ath10k!QCA9888!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed [ 10.984200] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/ct-firmware-2.bin failed with error -2 [ 10.992085] ath10k_pci 0000:01:00.0: Falling back to user helper [ 11.057547] firmware ath10k!QCA9888!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed [ 11.057968] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/firmware-6.bin failed with error -2 [ 11.065844] ath10k_pci 0000:01:00.0: Falling back to user helper [ 11.129819] firmware ath10k!QCA9888!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed [ 11.390841] ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000 [ 11.390887] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 11.402934] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9888-fW-012-17ba98334 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 a08ba414 [ 11.764897] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:17 crc32 f228337a [ 13.797229] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 13.797271] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32 [ 13.830809] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 13.831851] ath10k_pci 0000:01:00.0: wmi print 'free: 117888 iram: 22644 sram: 26276' [ 13.998405] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 14.145258] ath: EEPROM regdomain: 0x0 [ 14.145269] ath: EEPROM indicates default country code should be used [ 14.145274] ath: doing EEPROM country->regdmn map search [ 14.145284] ath: country maps to regdmn code: 0x3a [ 14.145292] ath: Country alpha2 being used: US [ 14.145297] ath: Regpair used: 0x3a [ 14.332452] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/fwcfg-ahb-a000000.wifi.txt failed with error -2 [ 14.332527] ath10k_ahb a000000.wifi: Falling back to user helper [ 14.902643] firmware ath10k!fwcfg-ahb-a000000.wifi.txt: firmware_loading_store: map pages failed [ 14.903026] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a000000.wifi.bin failed with error -2 [ 14.910580] ath10k_ahb a000000.wifi: Falling back to user helper [ 15.059589] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/ct-firmware-5.bin failed with error -2 [ 15.059641] ath10k_ahb a000000.wifi: Falling back to user helper [ 15.118956] firmware ath10k!QCA4019!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed [ 15.119277] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/ct-firmware-2.bin failed with error -2 [ 15.127293] ath10k_ahb a000000.wifi: Falling back to user helper [ 15.196667] firmware ath10k!QCA4019!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed [ 15.197060] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2 [ 15.204970] ath10k_ahb a000000.wifi: Falling back to user helper [ 15.274352] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed [ 15.517462] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 15.517507] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 15.529043] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-012-17ba98334 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 8f2e0e09 [ 15.618475] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 4329f4ee [ 16.927906] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 16.927955] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32 [ 16.962865] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 16.963859] ath10k_ahb a000000.wifi: wmi print 'free: 56528 iram: 23400 sram: 32520' [ 17.076965] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 17.313453] ath: EEPROM regdomain: 0x0 [ 17.313462] ath: EEPROM indicates default country code should be used [ 17.313466] ath: doing EEPROM country->regdmn map search [ 17.313473] ath: country maps to regdmn code: 0x3a [ 17.313479] ath: Country alpha2 being used: US [ 17.313482] ath: Regpair used: 0x3a [ 17.492184] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/fwcfg-ahb-a800000.wifi.txt failed with error -2 [ 17.492245] ath10k_ahb a800000.wifi: Falling back to user helper [ 17.685408] firmware ath10k!fwcfg-ahb-a800000.wifi.txt: firmware_loading_store: map pages failed [ 17.685822] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a800000.wifi.bin failed with error -2 [ 17.693392] ath10k_ahb a800000.wifi: Falling back to user helper [ 17.812964] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/ct-firmware-5.bin failed with error -2 [ 17.813008] ath10k_ahb a800000.wifi: Falling back to user helper [ 17.866598] firmware ath10k!QCA4019!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed [ 17.866944] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/ct-firmware-2.bin failed with error -2 [ 17.874904] ath10k_ahb a800000.wifi: Falling back to user helper [ 17.938738] firmware ath10k!QCA4019!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed [ 17.939020] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2 [ 17.947033] ath10k_ahb a800000.wifi: Falling back to user helper [ 18.008540] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed [ 18.008846] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000 [ 18.016506] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 18.030748] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-012-17ba98334 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 8f2e0e09 [ 18.081285] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 4329f4ee [ 19.390338] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 19.390379] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32 [ 19.439090] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 19.441105] ath10k_ahb a800000.wifi: wmi print 'free: 56528 iram: 23400 sram: 32520' [ 19.555755] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 19.675935] ath: EEPROM regdomain: 0x0 [ 19.675947] ath: EEPROM indicates default country code should be used [ 19.675952] ath: doing EEPROM country->regdmn map search [ 19.675962] ath: country maps to regdmn code: 0x3a [ 19.675969] ath: Country alpha2 being used: US [ 19.675974] ath: Regpair used: 0x3a [ 19.685101] kmodloader: done loading kernel modules from /etc/modules.d/* [ 44.611931] ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=100 [ 44.612750] br-lan: port 1(eth1) entered blocking state [ 44.617706] br-lan: port 1(eth1) entered disabled state [ 44.623341] device eth1 entered promiscuous mode [ 44.630394] br-lan: port 1(eth1) entered blocking state [ 44.633013] br-lan: port 1(eth1) entered forwarding state [ 44.638188] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 44.655401] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 45.689956] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 45.691600] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready


Space for additional notes, links to forum threads or other resources.

  • ...
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 11:13
  • by 127.0.0.1