Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revisionBoth sides next revision
toh:aruba:ap-303h-nand [2024/04/20 21:40] – created ryanrstoh:aruba:ap-303h-nand [2024/04/20 22:33] – install log ryanrs
Line 34: Line 34:
  
 power cycle, warm reboot not enough power cycle, warm reboot not enough
 +
 +
 +
 +
 +==== OpenWrt bootlog ====
 +<WRAP bootlog>
 +<nowiki>
 +APBoot 2.1.4.7 (build 57679)
 +Built: 2016-12-08 at 15:41:41
 +
 +Model: AP-303H
 +DRAM:  512 MiB
 +Flash: Detected MX25L3205D: total 4 MiB
 +NAND:  Detected MX35LFxGE4AB: total 128 MiB
 +Power: 802.3at POE
 +Net:   eth0
 +Radio: ipq4029#0, ipq4029#1
 +Reset: cold
 +**** Configuration Reset Requested by User ****
 +Clearing state... 
 +Checking OS image and flags
 +Invalid image format version: 0x0
 +Continuing with OS clear
 +512 bytes written to volume aos0
 +Erasing UBIFS ...OK
 +done
 +
 +Purging environment... 
 +preserving os_partition (1)
 +Erasing SPI flash...Writing to SPI flash...done
 +Erasing SPI flash...Writing to SPI flash...done
 +FIPS:  passed 
 +
 +Hit <Enter> to stop autoboot:  2  0 
 +apboot> mtdparts
 +
 +device nand0 <nand0>, # parts = 3
 + #: name size offset mask_flags
 + 0: aos0                0x02000000 0x00000000 0
 + 1: aos1                0x02000000 0x02000000 0
 + 2: ubifs               0x04000000 0x04000000 0
 +
 +active partition: nand0,0 - (aos0) 0x02000000 @ 0x00000000
 +
 +defaults:
 +mtdids  : nand0=nand0
 +mtdparts: none
 +apboot> ubi part aos0
 +apboot> ubi info
 +UBI: MTD device name:            "mtd=0"
 +UBI: MTD device size:            32 MiB
 +UBI: physical eraseblock size:   131072 bytes (128 KiB)
 +UBI: logical eraseblock size:    126976 bytes
 +UBI: number of good PEBs:        256
 +UBI: number of bad PEBs:         0
 +UBI: smallest flash I/O unit:    2048
 +UBI: VID header offset:          2048 (aligned 2048)
 +UBI: data offset:                4096
 +UBI: max. allowed volumes:       128
 +UBI: wear-leveling threshold:    4096
 +UBI: number of internal volumes: 1
 +UBI: number of user volumes:     1
 +UBI: available PEBs:             4
 +UBI: total number of reserved PEBs: 252
 +UBI: number of PEBs reserved for bad PEB handling: 4
 +UBI: max/mean erase counter: 12/4
 +apboot> ubi info layout
 +UBI: volume information dump:
 +UBI: vol_id          0
 +UBI: reserved_pebs   244
 +UBI: alignment       1
 +UBI: data_pad        0
 +UBI: vol_type        3
 +UBI: name_len        4
 +UBI: usable_leb_size 126976
 +UBI: used_ebs        244
 +UBI: used_bytes      30982144
 +UBI: last_eb_bytes   126976
 +UBI: corrupted       0
 +UBI: upd_marker      0
 +UBI: name            aos0
 +
 +UBI: volume information dump:
 +UBI: vol_id          2147479551
 +UBI: reserved_pebs   2
 +UBI: alignment       1
 +UBI: data_pad        0
 +UBI: vol_type        3
 +UBI: name_len        13
 +UBI: usable_leb_size 126976
 +UBI: used_ebs        2
 +UBI: used_bytes      253952
 +UBI: last_eb_bytes   2
 +UBI: corrupted       0
 +UBI: upd_marker      0
 +UBI: name            layout volume
 +
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> ubi part aos1
 +apboot> ubi part aos1             ubi info layout               ubi info
 +UBI: MTD device name:            "mtd=1"
 +UBI: MTD device size:            32 MiB
 +UBI: physical eraseblock size:   131072 bytes (128 KiB)
 +UBI: logical eraseblock size:    126976 bytes
 +UBI: number of good PEBs:        256
 +UBI: number of bad PEBs:         0
 +UBI: smallest flash I/O unit:    2048
 +UBI: VID header offset:          2048 (aligned 2048)
 +UBI: data offset:                4096
 +UBI: max. allowed volumes:       128
 +UBI: wear-leveling threshold:    4096
 +UBI: number of internal volumes: 1
 +UBI: number of user volumes:     1
 +UBI: available PEBs:             4
 +UBI: total number of reserved PEBs: 252
 +UBI: number of PEBs reserved for bad PEB handling: 4
 +UBI: max/mean erase counter: 7/5
 +apboot> ubi info        ubi part aos1             ubi info layout
 +UBI: volume information dump:
 +UBI: vol_id          0
 +UBI: reserved_pebs   244
 +UBI: alignment       1
 +UBI: data_pad        0
 +UBI: vol_type        3
 +UBI: name_len        4
 +UBI: usable_leb_size 126976
 +UBI: used_ebs        244
 +UBI: used_bytes      30982144
 +UBI: last_eb_bytes   126976
 +UBI: corrupted       0
 +UBI: upd_marker      0
 +UBI: name            aos1
 +
 +UBI: volume information dump:
 +UBI: vol_id          2147479551
 +UBI: reserved_pebs   2
 +UBI: alignment       1
 +UBI: data_pad        0
 +UBI: vol_type        3
 +UBI: name_len        13
 +UBI: usable_leb_size 126976
 +UBI: used_ebs        2
 +UBI: used_bytes      253952
 +UBI: last_eb_bytes   2
 +UBI: corrupted       0
 +UBI: upd_marker      0
 +UBI: name            layout volume
 +
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> ubi part ubifs
 +apboot> ubi part ubifs              ubi info layout               ubi info
 +UBI: MTD device name:            "mtd=2"
 +UBI: MTD device size:            64 MiB
 +UBI: physical eraseblock size:   131072 bytes (128 KiB)
 +UBI: logical eraseblock size:    126976 bytes
 +UBI: number of good PEBs:        511
 +UBI: number of bad PEBs:         1
 +UBI: smallest flash I/O unit:    2048
 +UBI: VID header offset:          2048 (aligned 2048)
 +UBI: data offset:                4096
 +UBI: max. allowed volumes:       128
 +UBI: wear-leveling threshold:    4096
 +UBI: number of internal volumes: 1
 +UBI: number of user volumes:     4
 +UBI: available PEBs:             4
 +UBI: total number of reserved PEBs: 507
 +UBI: number of PEBs reserved for bad PEB handling: 10
 +UBI: max/mean erase counter: 11/9
 +apboot> ubi info        ubi part ubifs              ubi info layout
 +UBI: volume information dump:
 +UBI: vol_id          0
 +UBI: reserved_pebs   25
 +UBI: alignment       1
 +UBI: data_pad        0
 +UBI: vol_type        3
 +UBI: name_len        6
 +UBI: usable_leb_size 126976
 +UBI: used_ebs        25
 +UBI: used_bytes      3174400
 +UBI: last_eb_bytes   126976
 +UBI: corrupted       0
 +UBI: upd_marker      0
 +UBI: name            kernel
 +
 +UBI: volume information dump:
 +UBI: vol_id          1
 +UBI: reserved_pebs   32
 +UBI: alignment       1
 +UBI: data_pad        0
 +UBI: vol_type        3
 +UBI: name_len        6
 +UBI: usable_leb_size 126976
 +UBI: used_ebs        32
 +UBI: used_bytes      4063232
 +UBI: last_eb_bytes   126976
 +UBI: corrupted       0
 +UBI: upd_marker      0
 +UBI: name            rootfs
 +
 +UBI: volume information dump:
 +UBI: vol_id          2
 +UBI: reserved_pebs   431
 +UBI: alignment       1
 +UBI: data_pad        0
 +UBI: vol_type        3
 +UBI: name_len        11
 +UBI: usable_leb_size 126976
 +UBI: used_ebs        431
 +UBI: used_bytes      54726656
 +UBI: last_eb_bytes   126976
 +UBI: corrupted       0
 +UBI: upd_marker      0
 +UBI: name            rootfs_data
 +
 +UBI: volume information dump:
 +UBI: vol_id          3
 +UBI: reserved_pebs   5
 +UBI: alignment       1
 +UBI: data_pad        0
 +UBI: vol_type        3
 +UBI: name_len        5
 +UBI: usable_leb_size 126976
 +UBI: used_ebs        5
 +UBI: used_bytes      634880
 +UBI: last_eb_bytes   126976
 +UBI: corrupted       0
 +UBI: upd_marker      0
 +UBI: name            ubifs
 +
 +UBI: volume information dump:
 +UBI: vol_id          2147479551
 +UBI: reserved_pebs   2
 +UBI: alignment       1
 +UBI: data_pad        0
 +UBI: vol_type        3
 +UBI: name_len        13
 +UBI: usable_leb_size 126976
 +UBI: used_ebs        2
 +UBI: used_bytes      253952
 +UBI: last_eb_bytes   2
 +UBI: corrupted       0
 +UBI: upd_marker      0
 +UBI: name            layout volume
 +
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> setenv bootargs_openwrt "setenv bootargs console=ttyMSM0,9600n8 mtdparts=spi0.1:0x2000000(aos0),0x2000000(aos1),0x4000000(ubi)"
 +apboot> setenv nandboot_openwrt "run bootargs_openwrt; ubi part ubifs; ubi read 0x85000000 kernel; set fdt_high 0x87000000; bootm 0x85000000"
 +apboot> setenv ramboot_openwrt "run bootargs_openwrt; setenv ipaddr 192.168.5.49; setenv serverip 192.168.5.30; netget; set fdt_high 0x87000000; bootm"
 +apboot> setenv bootcmd "run nandboot_openwrt"
 +apboot> printenv
 +autoload=n
 +autostart=yes
 +baudrate=9600
 +boardname=Aberlour
 +bootargs=console=ttyMSM0,9600n8 rdinit=/sbin/init ubi.mtd=aos0 ubi.mtd=aos1 ubi.mtd=ubifs
 +bootargs_openwrt=setenv bootargs console=ttyMSM0,9600n8 mtdparts=spi0.1:0x2000000(aos0),0x2000000(aos1),0x4000000(ubi)
 +bootcmd=run nandboot_openwrt
 +bootdelay=2
 +bootfile=ipq40xx.ari
 +ethaddr=20:4c:03:22:87:58
 +mtddevname=aos0
 +mtddevnum=0
 +mtdids=nand0=nand0
 +mtdparts=mtdparts=nand0:0x2000000@0x0(aos0),0x2000000@0x2000000(aos1),0x4000000@0x4000000(ubifs)
 +nandboot_openwrt=run bootargs_openwrt; ubi part ubifs; ubi read 0x85000000 kernel; set fdt_high 0x87000000; bootm 0x85000000
 +os_partition=1
 +partition=nand0,0
 +ramboot_openwrt=run bootargs_openwrt; setenv ipaddr 192.168.5.49; setenv serverip 192.168.5.30; netget; set fdt_high 0x87000000; bootm
 +servername=aruba-master
 +
 +Environment size: 855/65532 bytes
 +apboot> saveenv
 +Saving Environment to SPI Flash...
 +Erasing SPI flash...Writing to SPI flash...done
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> 
 +apboot> run ramboot_openwrt
 +eth0 up: 1 Gb/s full duplex
 +Using eth0 device
 +TFTP from server 192.168.5.30; our IP address is 192.168.5.49
 +Filename 'ipq40xx.ari'.
 +Load address: 0x84000000
 +Loading: *#################################################################
 + ##########################################
 + 821.3 KiB/s
 +done
 +Bytes transferred = 6835196 (684bfc hex)
 +Invalid image format version: 0x684bfc
 +Uncompressing Kernel Image ... OK
 +ipq: fdt fixup unable to find compatible node
 +[    0.000000] Booting Linux on physical CPU 0x0
 +[    0.000000] Linux version 5.15.150 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 12.3.0 r23809-234f1a2efa) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Fri Mar 22 22:09:42 2024
 +[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
 +[    0.000000] CPU: div instructions available: patching division code
 +[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
 +[    0.000000] OF: fdt: Machine model: Aruba AP-303H
 +[    0.000000] Memory policy: Data cache writealloc
 +[    0.000000] Zone ranges:
 +[    0.000000]   Normal   [mem 0x0000000080000000-0x000000009fffffff]
 +[    0.000000]   HighMem  empty
 +[    0.000000] Movable zone start for each node
 +[    0.000000] Early memory node ranges
 +[    0.000000]   node   0: [mem 0x0000000080000000-0x0000000087dfffff]
 +[    0.000000]   node   0: [mem 0x0000000087e00000-0x0000000087ffffff]
 +[    0.000000]   node   0: [mem 0x0000000088000000-0x000000009fffffff]
 +[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff]
 +[    0.000000] percpu: Embedded 12 pages/cpu s19660 r8192 d21300 u49152
 +[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129920
 +[    0.000000] Kernel command line: console=ttyMSM0,9600n8 mtdparts=spi0.1:0x2000000(aos0),0x2000000(aos1),0x4000000(ubi)
 +[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
 +[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
 +[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
 +[    0.000000] Memory: 494572K/524288K available (6751K kernel code, 610K rwdata, 1020K rodata, 13312K init, 246K bss, 29716K reserved, 0K cma-reserved, 0K highmem)
 +[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
 +[    0.000000] rcu: Hierarchical RCU implementation.
 +[    0.000000] Tracing variant of Tasks RCU enabled.
 +[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
 +[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
 +[    0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt).
 +[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns
 +[    0.000001] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns
 +[    0.000026] Switching to timer-based delay loop, resolution 20ns
 +[    0.000341] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
 +[    0.000368] CPU: Testing write buffer coherency: ok
 +[    0.000430] pid_max: default: 32768 minimum: 301
 +[    0.001280] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
 +[    0.001310] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
 +[    0.003382] qcom_scm: convention: smc legacy
 +[    0.004605] Setting up static identity map for 0x80300000 - 0x8030003c
 +[    0.004783] rcu: Hierarchical SRCU implementation.
 +[    0.005386] smp: Bringing up secondary CPUs ...
 +[    0.008999] smp: Brought up 1 node, 4 CPUs
 +[    0.009040] SMP: Total of 4 processors activated (384.00 BogoMIPS).
 +[    0.009056] CPU: All CPU(s) started in SVC mode.
 +[    0.015818] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
 +[    0.015992] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
 +[    0.016030] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
 +[    0.016430] pinctrl core: initialized pinctrl subsystem
 +[    0.018514] NET: Registered PF_NETLINK/PF_ROUTE protocol family
 +[    0.018910] DMA: preallocated 256 KiB pool for atomic coherent allocations
 +[    0.020307] thermal_sys: Registered thermal governor 'step_wise'
 +[    0.020764] cpuidle: using governor ladder
 +[    0.020833] cpuidle: using governor menu
 +[    0.029322] gpio-435 (USB-power): hogged as output/high
 +[    0.049493] cryptd: max_cpu_qlen set to 1000
 +[    0.054368] usbcore: registered new interface driver usbfs
 +[    0.054449] usbcore: registered new interface driver hub
 +[    0.054543] usbcore: registered new device driver usb
 +[    0.054602] pps_core: LinuxPPS API ver. 1 registered
 +[    0.054616] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
 +[    0.054645] PTP clock support registered
 +[    0.056962] clocksource: Switched to clocksource arch_sys_counter
 +[    0.058394] NET: Registered PF_INET protocol family
 +[    0.058665] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
 +[    0.059883] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
 +[    0.059943] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
 +[    0.059966] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
 +[    0.060030] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
 +[    0.060227] TCP: Hash tables configured (established 4096 bind 4096)
 +[    0.060401] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
 +[    0.060453] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
 +[    0.060802] NET: Registered PF_UNIX/PF_LOCAL protocol family
 +[    0.060858] PCI: CLS 0 bytes, default 64
 +[    0.063925] workingset: timestamp_bits=14 max_order=17 bucket_order=3
 +[    0.070297] squashfs: version 4.0 (2009/01/31) Phillip Lougher
 +[    0.070340] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.202798] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
 +[    0.207463] bam-dma-engine 8e04000.dma: num-channels unspecified in dt
 +[    0.207517] bam-dma-engine 8e04000.dma: num-ees unspecified in dt
 +[    0.209587] tcsr 1953000.ess_tcsr: setting ess interface select = 0
 +[    0.209728] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
 +[    0.209837] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
 +[    0.209938] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
 +[    0.210358] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
 +[    0.212749] msm_serial 78af000.serial: msm_serial: detected port #0
 +[    0.212819] msm_serial 78af000.serial: uartclk = 1843200
 +[    0.212934] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 34, base_baud = 115200) is a MSM
 +[    0.212985] msm_serial: console setup on port #0
 +[    6.896436] printk: console [ttyMSM0] enabled
 +[    6.953251] msm_serial 78b0000.serial: msm_serial: detected port #1
 +[    7.003778] msm_serial 78b0000.serial: uartclk = 48000000
 +[    7.076712] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 35, base_baud = 3000000) is a MSM
 +[    7.143732] msm_serial: driver initialized
 +[    7.251609] loop: module loaded
 +[    7.295575] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
 +[    7.331900] spi-nor spi0.0: mx25l3205d (4096 Kbytes)
 +[    7.418439] 15 fixed-partitions partitions found on MTD device spi0.0
 +[    7.477759] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions
 +[    7.553764] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions
 +[    7.631219] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions
 +[    7.708973] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions
 +[    7.787472] Creating 15 MTD partitions on "spi0.0":
 +[    7.865210] 0x000000000000-0x000000040000 : "sbl1"
 +[    7.923107] 0x000000040000-0x000000060000 : "mibib"
 +[    7.981466] 0x000000060000-0x0000000c0000 : "qsee"
 +[    8.038730] 0x0000000c0000-0x0000000d0000 : "cdt"
 +[    8.097488] 0x0000000d0000-0x0000000e0000 : "ddrparams"
 +[    8.154405] 0x0000000e0000-0x0000000f0000 : "appsblenv"
 +[    8.214766] 0x0000000f0000-0x0000001f0000 : "appsbl"
 +[    8.277260] 0x0000001f0000-0x000000200000 : "ART"
 +[    8.339813] 0x000000200000-0x000000370000 : "osss"
 +[    8.395019] 0x000000370000-0x000000380000 : "pds"
 +[    8.451197] 0x000000380000-0x000000390000 : "apcd"
 +[    8.508564] 0x000000390000-0x0000003a0000 : "mfginfo"
 +[    8.564802] 0x0000003a0000-0x0000003b0000 : "fcache"
 +[    8.626177] 0x0000003b0000-0x0000003c0000 : "u-boot-env-bak"
 +[    8.686617] 0x0000003c0000-0x000000400000 : "u-boot-env"
 +[    8.761414] spi-nand spi0.1: Macronix SPI NAND was found.
 +[    8.817316] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
 +[    8.881212] mtd: Found partition defined in DT for aos0. Assigning OF node to support nvmem.
 +[    8.881236] 3 cmdlinepart partitions found on MTD device spi0.1
 +[    9.079779] Creating 3 MTD partitions on "spi0.1":
 +[    9.147481] 0x000000000000-0x000002000000 : "aos0"
 +[    9.303567] 0x000002000000-0x000004000000 : "aos1"
 +[    9.401009] 0x000004000000-0x000008000000 : "ubi"
 +[    9.710793] i2c_dev: i2c /dev entries driver
 +[    9.711137] i2c_qup 78b7000.i2c: using default clock-frequency 100000
 +[    9.753421] sdhci: Secure Digital Host Controller Interface driver
 +[    9.826519] sdhci: Copyright(c) Pierre Ossman
 +[    9.899406] sdhci-pltfm: SDHCI platform and OF driver helper
 +[    9.956819] NET: Registered PF_INET6 protocol family
 +[   10.023220] Segment Routing with IPv6
 +[   10.080772] In-situ OAM (IOAM) with IPv6
 +[   10.123470] NET: Registered PF_PACKET protocol family
 +[   10.171394] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
 +[   10.231084] 8021q: 802.1Q VLAN Support v1.8
 +[   10.387025] Registering SWP/SWPB emulation handler
 +[   10.466254] qca8k-ipq4019 c000000.switch: configuring for fixed/internal link mode
 +[   10.492420] qca8k-ipq4019 c000000.switch: Link is Up - 1Gbps/Full - flow control rx/tx
 +[   10.590291] qca8k-ipq4019 c000000.switch lan1 (uninitialized): PHY [90000.mdio-1:01] driver [Qualcomm QCA8075] (irq=POLL)
 +[   10.760275] qca8k-ipq4019 c000000.switch lan2 (uninitialized): PHY [90000.mdio-1:02] driver [Qualcomm QCA8075] (irq=POLL)
 +[   10.890368] qca8k-ipq4019 c000000.switch lan3 (uninitialized): PHY [90000.mdio-1:03] driver [Qualcomm QCA8075] (irq=POLL)
 +[   11.021879] qca8k-ipq4019 c000000.switch wan (uninitialized): PHY [90000.mdio-1:04] driver [Qualcomm QCA8075] (irq=POLL)
 +[   11.073305] DSA: treˇ[   11.263102] Freeing unused kernel image (initmem) memory: 13312K
 +[   11.263404] Run /init as init process
 +[   11.788521] init: Console is alive
 +[   11.788892] init: - watchdog -
 +[   11.825738] kmodloader: loading kernel modules from /etc/modules-boot.d/*
 +[   11.955845] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
 +[   11.955929] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
 +[   12.008310] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x0000008002010010
 +[   12.098723] xhci-hcd xhci-hcd.0.auto: irq 104, io mem 0x06000000
 +[   12.211335] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
 +[   12.286161] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
 +[   12.349688] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
 +[   12.441057] hub 1-0:1.0: USB hub found
 +[   12.519531] hub 1-0:1.0: 1 port detected
 +[   12.567982] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
 +[   12.613902] hub 2-0:1.0: USB hub found
 +[   12.710154] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
 +[   12.756071] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
 +[   12.844613] init: - preinit -
 +[   12.906971] usb 1-1: new full-speed USB device number 2 using xhci-hcd
 +[   13.108228] random: jshn: uninitialized urandom read (4 bytes read)
 +[   13.117100] usb 1-1: device descriptor read/64, error -71
 +[   13.154186] random: jshn: uninitialized urandom read (4 bytes read)
 +[   13.263597] random: jshn: uninitialized urandom read (4 bytes read)
 +[   13.437087] usb 1-1: device descriptor read/64, error -71
 +[   13.516666] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode
 +[   13.517533] qca8k-ipq4019 c000000.switch lan1: configuring for phy/psgmii link mode
 +[   13.598196] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
 +[   13.746974] usb 1-1: new full-speed USB device number 3 using xhci-hcd
 +[   13.957005] usb 1-1: device descriptor read/64, error -71
 +[   14.226999] usb 1-1: device descriptor read/64, error -71
 +[   14.347200] usb usb1-port1: attempt power cycle
 +[   14.518456] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
 +[   14.532109] random: procd: uninitialized urandom read (4 bytes read)
 +Press the [f] key and hit [enter] to enter failsafe mode
 +Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
 +[   14.816989] usb 1-1: new full-speed USB device number 4 using xhci-hcd
 +[   14.817153] usb 1-1: Device not responding to setup address.
 +[   15.097051] usb 1-1: Device not responding to setup address.
 +[   15.316965] usb 1-1: device not accepting address 4, error -71
 +[   15.466969] usb 1-1: new full-speed USB device number 5 using xhci-hcd
 +[   15.467098] usb 1-1: Device not responding to setup address.
 +[   15.747089] usb 1-1: Device not responding to setup address.
 +[   15.966975] usb 1-1: device not accepting address 5, error -71
 +[   15.967241] usb usb1-port1: unable to enumerate USB device
 +[   16.638746] procd: - early -
 +[   16.638973] procd: - watchdog -
 +[   17.221975] procd: - watchdog -
 +[   17.222382] procd: - ubus -
 +[   17.251326] random: ubusd: uninitialized urandom read (4 bytes read)
 +[   17.295622] random: ubusd: uninitialized urandom read (4 bytes read)
 +[   17.357823] random: ubusd: uninitialized urandom read (4 bytes read)
 +[   17.435967] procd: - init -
 +Please press Enter to activate this console.
 +[   17.827774] kmodloader: loading kernel modules from /etc/modules.d/*
 +[   17.836543] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
 +[   17.892480] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
 +[   18.068598] PPP generic driver version 2.4.2
 +[   18.069660] NET: Registered PF_PPPOX protocol family
 +[   18.663942] urngd: v1.0.2 started.
 +[   18.938945] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003900ff sub 0000:0000
 +[   18.939023] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
 +[   19.040744] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
 +[   19.208058] random: crng init done
 +[   19.258181] ath10k_ahb a000000.wifi: Loading BDF type 0
 +[   19.478659] random: 29 urandom warning(s) missed due to ratelimiting
 +[   19.533567] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 d140cd7d
 +[   20.950595] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
 +[   20.950678] ath10k_ahb a000000.wifi: msdu-desc: 2500  skid: 32
 +[   21.070542] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
 +[   21.096594] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
 +[   21.404661] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
 +[   22.441200] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003900ff sub 0000:0000
 +[   22.441286] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
 +[   22.543023] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
 +[   22.760350] ath10k_ahb a800000.wifi: Loading BDF type 0
 +[   22.993218] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 d140cd7d
 +[   24.333452] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
 +[   24.333528] ath10k_ahb a800000.wifi: msdu-desc: 2500  skid: 32
 +[   24.453011] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
 +[   24.479439] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
 +[   24.742253] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
 +[   24.870290] kmodloader: done loading kernel modules from /etc/modules.d/*
 +[   52.993270] ipqess-edma c080000.ethernet eth0: Link is Down
 +[   52.998905] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode
 +[   53.045943] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
 +[   53.054685] qca8k-ipq4019 c000000.switch lan1: configuring for phy/psgmii link mode
 +[   53.242010] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
 +[   53.333813] br-lan: port 1(lan1) entered blocking state
 +[   53.408052] br-lan: port 1(lan1) entered disabled state
 +[   53.471002] device lan1 entered promiscuous mode
 +[   53.532995] device eth0 entered promiscuous mode
 +[   53.609390] qca8k-ipq4019 c000000.switch lan2: configuring for phy/psgmii link mode
 +[   53.649157] br-lan: port 2(lan2) entered blocking state
 +[   53.735163] br-lan: port 2(lan2) entered disabled state
 +[   53.798077] device lan2 entered promiscuous mode
 +[   53.868686] qca8k-ipq4019 c000000.switch lan3: configuring for phy/psgmii link mode
 +[   53.920578] br-lan: port 3(lan3) entered blocking state
 +[   54.006996] br-lan: port 3(lan3) entered disabled state
 +[   54.069848] device lan3 entered promiscuous mode
 +[   54.141319] qca8k-ipq4019 c000000.switch wan: configuring for phy/psgmii link mode
 +[   57.278123] qca8k-ipq4019 c000000.switch wan: Link is Up - 1Gbps/Full - flow control off
 +[   57.278211] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready
 +
 +
 +
 +BusyBox v1.36.1 (2024-03-22 22:09:42 UTC) built-in shell (ash)
 +
 +  _______                     ________        __
 +       |.-----.-----.-----.|  |  |  |.----.|  |_
 +     ||  _  |  -__|     ||  |  |  ||   _||   _|
 + |_______||   __|_____|__|__||________||__|  |____|
 +          |__| W I R E L E S S   F R E E D O M
 + -----------------------------------------------------
 + OpenWrt 23.05.3, r23809-234f1a2efa
 + -----------------------------------------------------
 +=== WARNING! =====================================
 +There is no root password defined on this device!
 +Use the "passwd" command to set up a new password
 +in order to prevent unauthorized SSH logins.
 +--------------------------------------------------
 +root@OpenWrt:/# mount
 +tmpfs on / type tmpfs (rw,relatime)
 +proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
 +sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
 +cgroup2 on /sys/fs/cgroup type cgroup2 (rw,nosuid,nodev,noexec,relatime,nsdelegate)
 +tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
 +tmpfs on /dev type tmpfs (rw,nosuid,noexec,noatime,size=512k,mode=755)
 +devpts on /dev/pts type devpts (rw,nosuid,noexec,noatime,mode=600,ptmxmode=000)
 +debugfs on /sys/kernel/debug type debugfs (rw,noatime)
 +bpffs on /sys/fs/bpf type bpf (rw,nosuid,nodev,noexec,noatime,mode=700)
 +root@OpenWrt:/# cat /proc/mt
 +root@OpenWrt:/# cat /proc/mtd 
 +dev:    size   erasesize  name
 +mtd0: 00040000 00010000 "sbl1"
 +mtd1: 00020000 00010000 "mibib"
 +mtd2: 00060000 00010000 "qsee"
 +mtd3: 00010000 00010000 "cdt"
 +mtd4: 00010000 00010000 "ddrparams"
 +mtd5: 00010000 00010000 "appsblenv"
 +mtd6: 00100000 00010000 "appsbl"
 +mtd7: 00010000 00010000 "ART"
 +mtd8: 00170000 00010000 "osss"
 +mtd9: 00010000 00010000 "pds"
 +mtd10: 00010000 00010000 "apcd"
 +mtd11: 00010000 00010000 "mfginfo"
 +mtd12: 00010000 00010000 "fcache"
 +mtd13: 00010000 00010000 "u-boot-env-bak"
 +mtd14: 00040000 00010000 "u-boot-env"
 +mtd15: 02000000 00020000 "aos0"
 +mtd16: 02000000 00020000 "aos1"
 +mtd17: 04000000 00020000 "ubi"
 +root@OpenWrt:/# ubinfo -a
 +UBI version:                    1
 +Count of UBI devices:           0
 +UBI control device major/minor: 10:126
 +root@OpenWrt:/# ubidetach -p /dev/mtd17
 +ubidetach: error!: cannot detach "/dev/mtd17"
 +           error 19 (No such device)
 +root@OpenWrt:/# ubiformat /dev/mtd17
 +ubiformat: mtd17 (nand), size 67108864 bytes (64.0 MiB), 512 eraseblocks of 131072 bytes (128.0 KiB), min. I/O size 2048 bytes
 +
 +libscan: scanning eraseblock 511 -- 100 % complete  
 +ubiformat: 4 eraseblocks have valid erase counter, mean value is 10
 +ubiformat: 507 eraseblocks are supposedly empty
 +ubiformat: 1 bad eraseblocks found, numbers: 126
 +ubiformat: warning!: only 4 of 511 eraseblocks have valid erase counter
 +ubiformat: erase counter 0 will be used for all eraseblocks
 +ubiformat: note, arbitrary erase counter value may be specified using -e option
 +ubiformat: continue? (y/N) y
 +ubiformat: use erase counter 0 for all eraseblocks
 +
 +ubiformat: formatting eraseblock 511 -- 100 % complete  
 +root@OpenWrt:/# 
 +root@OpenWrt:/# ubiformat /dev/mtd176
 +ubiformat: mtd16 (nand), size 33554432 bytes (32.0 MiB), 256 eraseblocks of 131072 bytes (128.0 KiB), min. I/O size 2048 bytes
 +
 +libscan: scanning eraseblock 255 -- 100 % complete  
 +ubiformat: 256 eraseblocks have valid erase counter, mean value is 5
 +
 +ubiformat: formatting eraseblock 255 -- 100 % complete  
 +root@OpenWrt:/# 
 +root@OpenWrt:/# ubiformat /dev/mtd165
 +ubiformat: mtd15 (nand), size 33554432 bytes (32.0 MiB), 256 eraseblocks of 131072 bytes (128.0 KiB), min. I/O size 2048 bytes
 +
 +libscan: scanning eraseblock 255 -- 100 % complete  
 +ubiformat: 256 eraseblocks have valid erase counter, mean value is 4
 +
 +ubiformat: formatting eraseblock 255 -- 100 % complete  
 +root@OpenWrt:/# scp ryan@192.168.5.20:aruba-ap-303h/openwrt-23.05.3-fa3757f605bb-ipq40xx-generic-aruba_ap-303h-squashfs-sysupgrade.bin /tmp/openwrt-sysupgrade.bin
 +
 +Host '192.168.5.20' is not in the trusted hosts file.
 +(ssh-ed25519 fingerprint SHA256:pYIKrQTXM/ebww3nCZ2jHyhDyl4S9+dmYl6yn3nsAMM)
 +Do you want to continue connecting? (y/n) y
 +ryan@192.168.5.20's password: 
 +
 +openwrt-23.05.3-fa3757f605bb-ipq40xx-generic-   0%    0     0.0KB/  --:-- ETA
 +openwrt-23.05.3-fa3757f605bb-ipq40xx-generic- 100% 6901KB   6.7MB/  00:01    
 +root@OpenWrt:/# sysupgrade -n /tmp/openwrt-sysupgrade.bin
 +Sat Apr 20 19:50:30 UTC 2024 upgrade: Commencing upgrade. Closing all shell sessions.
 +- watchdog -
 +Watchdog did not previously reset the system
 +Sat Apr 20 19:50:31 UTC 2024 upgrade: Sending TERM to remaining processes ...
 +Sat Apr 20 19:50:35 UTC 2024 upgrade: Sending KILL to remaining processes ...
 +[  361.756610] stage2 (4182): drop_caches: 3
 +Sat Apr 20 19:50:41 UTC 2024 upgrade: Switching to ramdisk...
 +Sat Apr 20 19:50:43 UTC 2024 upgrade: Performing system upgrade...
 +verifying sysupgrade tar file integrity
 +[  364.584178] ubi0: attaching mtd17
 +[  365.847870] ubi0: scanning is finished
 +[  365.877077] ubi0: attached mtd17 (name "ubi", size 64 MiB)
 +[  365.879185] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
 +[  365.944843] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
 +[  366.027135] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
 +[  366.109423] ubi0: good PEBs: 511, bad PEBs: 1, corrupted PEBs: 0
 +[  366.190659] ubi0: user volume: 0, internal volumes: 1, max. volumes count: 128
 +[  366.265671] ubi0: max/mean erase counter: 0/0, WL threshold: 4096, image sequence number: 315897415
 +[  366.350042] ubi0: available PEBs: 488, total reserved PEBs: 23, PEBs reserved for bad PEB handling: 19
 +[  366.457355] ubi0: background thread "ubi_bgt0d" started, PID 4880
 +UBI device number 0, total 511 LEBs (64884736 bytes, 61.8 MiB), available 488 LEBs (61964288 bytes, 59.0 MiB), LEB size 126976 bytes (124.0 KiB)
 +Volume ID 0, size 25 LEBs (3174400 bytes, 3.0 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "kernel", alignment 1
 +Volume ID 1, size 32 LEBs (4063232 bytes, 3.8 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs", alignment 1
 +Set volume size to 54726656
 +Volume ID 2, size 431 LEBs (54726656 bytes, 52.1 MiB), LEB size 126976 bytes (124.0 KiB), dynamic, name "rootfs_data", alignment 1
 +sysupgrade
 +APBoot 2.1.4.7 (build 57679)
 +Built: 2016-12-08 at 15:41:41
 +
 +Model: AP-303H
 +DRAM:  512 MiB
 +Flash: Detected MX25L3205D: total 4 MiB
 +NAND:  Detected MX35LFxGE4AB: total 128 MiB
 +Power: 802.3at POE
 +Volume aos0 not found!
 +Creating dynamic volume aos0 of size 30982144
 +Volume aos1 not found!
 +Creating dynamic volume aos1 of size 30982144
 +Volume ubifs not found!
 +Creating dynamic volume ubifs of size 634880
 +Net:   eth0
 +Radio: ipq4029#0, ipq4029#1
 +Reset: warm
 +FIPS:  passed 
 +
 +Hit <Enter> to stop autoboot:  2  1  0 
 +No size specified -> Using max size (3174400)
 +Uncompressing Kernel Image ... 
 +APBoot 2.1.4.7 (build 57679)
 +Built: 2016-12-08 at 15:41:41
 +
 +Model: AP-303H
 +DRAM:  512 MiB
 +Flash: Detected MX25L3205D: total 4 MiB
 +NAND:  Detected MX35LFxGE4AB: total 128 MiB
 +Power: 802.3at POE
 +Net:   eth0
 +Radio: ipq4029#0, ipq4029#1
 +Reset: cold
 +FIPS:  passed 
 +
 +Hit <Enter> to stop autoboot:  2  1  0 
 +No size specified -> Using max size (3174400)
 +Uncompressing Kernel Image ... OK
 +ipq: fdt fixup unable to find compatible node
 +[    0.000000] Booting Linux on physical CPU 0x0
 +[    0.000000] Linux version 5.15.150 (builder@buildhost) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 12.3.0 r23809-234f1a2efa) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 SMP Fri Mar 22 22:09:42 2024
 +[    0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
 +[    0.000000] CPU: div instructions available: patching division code
 +[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
 +[    0.000000] OF: fdt: Machine model: Aruba AP-303H
 +[    0.000000] Memory policy: Data cache writealloc
 +[    0.000000] Zone ranges:
 +[    0.000000]   Normal   [mem 0x0000000080000000-0x000000009fffffff]
 +[    0.000000]   HighMem  empty
 +[    0.000000] Movable zone start for each node
 +[    0.000000] Early memory node ranges
 +[    0.000000]   node   0: [mem 0x0000000080000000-0x0000000087dfffff]
 +[    0.000000]   node   0: [mem 0x0000000087e00000-0x0000000087ffffff]
 +[    0.000000]   node   0: [mem 0x0000000088000000-0x000000009fffffff]
 +[    0.000000] Initmem setup node 0 [mem 0x0000000080000000-0x000000009fffffff]
 +[    0.000000] percpu: Embedded 12 pages/cpu s19660 r8192 d21300 u49152
 +[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 129920
 +[    0.000000] Kernel command line: console=ttyMSM0,9600n8 mtdparts=spi0.1:0x2000000(aos0),0x2000000(aos1),0x4000000(ubi)
 +[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear)
 +[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear)
 +[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
 +[    0.000000] Memory: 506860K/524288K available (6751K kernel code, 610K rwdata, 1020K rodata, 1024K init, 246K bss, 17428K reserved, 0K cma-reserved, 0K highmem)
 +[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
 +[    0.000000] rcu: Hierarchical RCU implementation.
 +[    0.000000] Tracing variant of Tasks RCU enabled.
 +[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
 +[    0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16
 +[    0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt).
 +[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns
 +[    0.000001] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns
 +[    0.000025] Switching to timer-based delay loop, resolution 20ns
 +[    0.000339] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)
 +[    0.000368] CPU: Testing write buffer coherency: ok
 +[    0.000428] pid_max: default: 32768 minimum: 301
 +[    0.001275] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
 +[    0.001308] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear)
 +[    0.003392] qcom_scm: convention: smc legacy
 +[    0.004619] Setting up static identity map for 0x80300000 - 0x8030003c
 +[    0.004801] rcu: Hierarchical SRCU implementation.
 +[    0.005412] smp: Bringing up secondary CPUs ...
 +[    0.009037] smp: Brought up 1 node, 4 CPUs
 +[    0.009075] SMP: Total of 4 processors activated (384.00 BogoMIPS).
 +[    0.009091] CPU: All CPU(s) started in SVC mode.
 +[    0.015850] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
 +[    0.016024] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
 +[    0.016061] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
 +[    0.016451] pinctrl core: initialized pinctrl subsystem
 +[    0.018540] NET: Registered PF_NETLINK/PF_ROUTE protocol family
 +[    0.018940] DMA: preallocated 256 KiB pool for atomic coherent allocations
 +[    0.020346] thermal_sys: Registered thermal governor 'step_wise'
 +[    0.020849] cpuidle: using governor ladder
 +[    0.020919] cpuidle: using governor menu
 +[    0.029416] gpio-435 (USB-power): hogged as output/high
 +[    0.049659] cryptd: max_cpu_qlen set to 1000
 +[    0.054572] usbcore: registered new interface driver usbfs
 +[    0.054655] usbcore: registered new interface driver hub
 +[    0.054750] usbcore: registered new device driver usb
 +[    0.054809] pps_core: LinuxPPS API ver. 1 registered
 +[    0.054821] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
 +[    0.054852] PTP clock support registered
 +[    0.057127] clocksource: Switched to clocksource arch_sys_counter
 +[    0.058565] NET: Registered PF_INET protocol family
 +[    0.058834] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear)
 +[    0.060037] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear)
 +[    0.060183] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
 +[    0.060213] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear)
 +[    0.060280] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear)
 +[    0.060374] TCP: Hash tables configured (established 4096 bind 4096)
 +[    0.060530] UDP hash table entries: 256 (order: 1, 8192 bytes, linear)
 +[    0.060580] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear)
 +[    0.060930] NET: Registered PF_UNIX/PF_LOCAL protocol family
 +[    0.060989] PCI: CLS 0 bytes, default 64
 +[    0.063340] workingset: timestamp_bits=14 max_order=17 bucket_order=3
 +[    0.069281] squashfs: version 4.0 (2009/01/31) Phillip Lougher
 +[    0.069317] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.200624] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
 +[    0.204643] bam-dma-engine 8e04000.dma: num-channels unspecified in dt
 +[    0.204678] bam-dma-engine 8e04000.dma: num-ees unspecified in dt
 +[    0.206294] tcsr 1953000.ess_tcsr: setting ess interface select = 0
 +[    0.206410] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000
 +[    0.206503] tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7
 +[    0.206595] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222
 +[    0.206966] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
 +[    0.209174] msm_serial 78af000.serial: msm_serial: detected port #0
 +[    0.209237] msm_serial 78af000.serial: uartclk = 1843200
 +[    0.209338] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 34, base_baud = 115200) is a MSM
 +[    0.209384] msm_serial: console setup on port #0
 +[    6.891789] printk: console [ttyMSM0] enabled
 +[    6.948588] msm_serial 78b0000.serial: msm_serial: detected port #1
 +[    6.999124] msm_serial 78b0000.serial: uartclk = 48000000
 +[    7.072068] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 35, base_baud = 3000000) is a MSM
 +[    7.139079] msm_serial: driver initialized
 +[    7.246773] loop: module loaded
 +[    7.290935] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
 +[    7.327532] spi-nor spi0.0: mx25l3205d (4096 Kbytes)
 +[    7.413792] 15 fixed-partitions partitions found on MTD device spi0.0
 +[    7.473073] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions
 +[    7.549116] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions
 +[    7.626593] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions
 +[    7.704335] OF: Bad cell count for /soc/spi@78b5000/flash@0/partitions
 +[    7.782832] Creating 15 MTD partitions on "spi0.0":
 +[    7.860564] 0x000000000000-0x000000040000 : "sbl1"
 +[    7.918478] 0x000000040000-0x000000060000 : "mibib"
 +[    7.976807] 0x000000060000-0x0000000c0000 : "qsee"
 +[    8.034098] 0x0000000c0000-0x0000000d0000 : "cdt"
 +[    8.092511] 0x0000000d0000-0x0000000e0000 : "ddrparams"
 +[    8.149646] 0x0000000e0000-0x0000000f0000 : "appsblenv"
 +[    8.210078] 0x0000000f0000-0x0000001f0000 : "appsbl"
 +[    8.272632] 0x0000001f0000-0x000000200000 : "ART"
 +[    8.335170] 0x000000200000-0x000000370000 : "osss"
 +[    8.390467] 0x000000370000-0x000000380000 : "pds"
 +[    8.446577] 0x000000380000-0x000000390000 : "apcd"
 +[    8.503949] 0x000000390000-0x0000003a0000 : "mfginfo"
 +[    8.560189] 0x0000003a0000-0x0000003b0000 : "fcache"
 +[    8.621497] 0x0000003b0000-0x0000003c0000 : "u-boot-env-bak"
 +[    8.681988] 0x0000003c0000-0x000000400000 : "u-boot-env"
 +[    8.756572] spi-nand spi0.1: Macronix SPI NAND was found.
 +[    8.812685] spi-nand spi0.1: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64
 +[    8.876472] mtd: Found partition defined in DT for aos0. Assigning OF node to support nvmem.
 +[    8.876499] 3 cmdlinepart partitions found on MTD device spi0.1
 +[    9.075115] Creating 3 MTD partitions on "spi0.1":
 +[    9.142853] 0x000000000000-0x000002000000 : "aos0"
 +[    9.271304] 0x000002000000-0x000004000000 : "aos1"
 +[    9.341531] 0x000004000000-0x000008000000 : "ubi"
 +[    9.537042] i2c_dev: i2c /dev entries driver
 +[    9.537397] i2c_qup 78b7000.i2c: using default clock-frequency 100000
 +[    9.579613] sdhci: Secure Digital Host Controller Interface driver
 +[    9.652764] sdhci: Copyright(c) Pierre Ossman
 +[    9.725656] sdhci-pltfm: SDHCI platform and OF driver helper
 +[    9.782623] NET: Registered PF_INET6 protocol family
 +[    9.849136] Segment Routing with IPv6
 +[    9.906984] In-situ OAM (IOAM) with IPv6
 +[    9.949728] NET: Registered PF_PACKET protocol family
 +[    9.997606] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.
 +[   10.057288] 8021q: 802.1Q VLAN Support v1.8
 +[   10.213271] Registering SWP/SWPB emulation handler
 +[   10.272500] qca8k-ipq4019 c000000.switch: configuring for fixed/internal link mode
 +[   10.318655] qca8k-ipq4019 c000000.switch: Link is Up - 1Gbps/Full - flow control rx/tx
 +[   10.420418] qca8k-ipq4019 c000000.switch lan1 (uninitialized): PHY [90000.mdio-1:01] driver [Qualcomm QCA8075] (irq=POLL)
 +[   10.580537] qca8k-ipq4019 c000000.switch lan2 (uninitialized): PHY [90000.mdio-1:02] driver [Qualcomm QCA8075] (irq=POLL)
 +[   10.720524] qca8k-ipq4019 c000000.switch lan3 (uninitialized): PHY [90000.mdio-1:03] driver [Qualcomm QCA8075] (irq=POLL)
 +[   10.852038] qca8k-ipq4019 c000000.switch wan (uninitialized): PHY [90000.mdio-1:04] driver [Qualcomm QCA8075] (irq=POLL)
 +[   10.899478] DSA: tree 0 setup
 +[   11.031690] UBI: auto-attach mtd17
 +[   11.064256] ubi0: attaching mtd17
 +[   12.147143] random: crng init done
 +[   12.239728] ubi0: scanning is finished
 +[   12.265317] ubi0 warning: 0xc0709018: cannot reserve enough PEBs for bad PEB handling, reserved 14, need 19
 +[   12.272124] ubi0: attached mtd17 (name "ubi", size 64 MiB)
 +[   12.386692] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes
 +[   12.453349] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048
 +[   12.535634] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096
 +[   12.617927] ubi0: good PEBs: 511, bad PEBs: 1, corrupted PEBs: 0
 +[   12.699169] ubi0: user volume: 4, internal volumes: 1, max. volumes count: 128
 +[   12.774176] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 315897415
 +[   12.858553] ubi0: available PEBs: 0, total reserved PEBs: 511, PEBs reserved for bad PEB handling: 14
 +[   12.965869] ubi0: background thread "ubi_bgt0d" started, PID 132
 +[   12.967884] block ubiblock0_1: created from ubi0˛[   13.232586] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.
 +[   13.234635] Freeing unused kernel image (initmem) memory: 1024K
 +[   13.347386] Run /sbin/init as init process
 +[   13.930144] init: Console is alive
 +[   13.930511] init: - watchdog -
 +[   15.187773] kmodloader: loading kernel modules from /etc/modules-boot.d/*
 +[   15.446114] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
 +[   15.446200] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
 +[   15.498569] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x0000008002010010
 +[   15.588999] xhci-hcd xhci-hcd.0.auto: irq 104, io mem 0x06000000
 +[   15.701600] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
 +[   15.776432] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
 +[   15.839957] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed
 +[   15.931355] hub 1-0:1.0: USB hub found
 +[   16.009839] hub 1-0:1.0: 1 port detected
 +[   16.058160] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
 +[   16.104193] hub 2-0:1.0: USB hub found
 +[   16.200431] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
 +[   16.246319] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
 +[   16.337722] init: - preinit -
 +[   16.397134] usb 1-1: new full-speed USB device number 2 using xhci-hcd
 +[   16.607208] usb 1-1: device descriptor read/64, error -71
 +[   16.877187] usb 1-1: device descriptor read/64, error -71
 +[   17.147236] usb 1-1: new full-speed USB device number 3 using xhci-hcd
 +[   17.297268] usb 1-1: device descriptor read/64, error -71
 +[   17.567268] usb 1-1: device descriptor read/64, error -71
 +[   17.687504] usb usb1-port1: attempt power cycle
 +[   17.689410] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode
 +[   17.727907] qca8k-ipq4019 c000000.switch lan1: configuring for phy/psgmii link mode
 +[   17.823143] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
 +[   18.317133] usb 1-1: new full-speed USB device number 4 using xhci-hcd
 +[   18.317282] usb 1-1: Device not responding to setup address.
 +[   18.597245] usb 1-1: Device not responding to setup address.
 +[   18.786704] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
 +[   18.817201] usb 1-1: device not accepting address 4, error -71
 +Press the [f] key and hit [enter] to enter failsafe mode
 +Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
 +[   19.007147] usb 1-1: new full-speed USB device number 5 using xhci-hcd
 +[   19.587130] usb 1-1: device not accepting address 5, error -71
 +[   19.587377] usb usb1-port1: unable to enumerate USB device
 +[   20.989010] UBIFS (ubi0:2): default file-system created
 +[   20.991335] UBIFS (ubi0:2): Mounting in unauthenticated mode
 +[   21.037264] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 239
 +[   21.255932] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data"
 +[   21.255998] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes
 +[   21.337309] UBIFS (ubi0:2): FS size: 53456896 bytes (50 MiB, 421 LEBs), max 431 LEBs, journal size 2666496 bytes (2 MiB, 21 LEBs)
 +[   21.456047] UBIFS (ubi0:2): reserved for root: 2524900 bytes (2465 KiB)
 +[   21.595616] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 07C7E3FF-218C-4877-B3BD-7B58AA6C14CA, small LPT model
 +[   21.677557] mount_root: overlay filesystem has not been fully initialized yet
 +[   21.810895] mount_root: switching to ubifs overlay
 +[   21.905628] urandom-seed: Seed file not found (/etc/urandom.seed)
 +[   22.181651] procd: - early -
 +[   22.181877] procd: - watchdog -
 +[   22.867962] procd: - watchdog -
 +[   23.018810] procd: - ubus -
 +[   23.194968] procd: - init -
 +Please press Enter to activate this console.
 +[   23.964844] kmodloader: loading kernel modules from /etc/modules.d/*
 +[   24.185831] Loading modules backported from Linux version v6.1.24-0-g0102425ac76b
 +[   24.185891] Backport generated by backports.git v5.15.92-1-44-gd6ea70fafd36
 +[   24.374761] PPP generic driver version 2.4.2
 +[   24.375945] NET: Registered PF_PPPOX protocol family
 +[   24.881233] urngd: v1.0.2 started.
 +[   25.842756] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003900ff sub 0000:0000
 +[   25.842829] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
 +[   25.944559] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
 +[   26.161895] ath10k_ahb a000000.wifi: Loading BDF type 0
 +[   26.505540] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 d140cd7d
 +[   27.798731] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
 +[   27.798811] ath10k_ahb a000000.wifi: msdu-desc: 2500  skid: 32
 +[   27.918381] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
 +[   27.944716] ath10k_ahb a000000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
 +[   28.280224] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
 +[   29.888293] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003900ff sub 0000:0000
 +[   29.888368] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0
 +[   29.990100] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 6b2b5c5b
 +[   30.207452] ath10k_ahb a800000.wifi: Loading BDF type 0
 +[   30.440286] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 d140cd7d
 +[   31.780595] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16  peers: 48  tid: 96
 +[   31.780674] ath10k_ahb a800000.wifi: msdu-desc: 2500  skid: 32
 +[   31.900151] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186  msdu-desc: 2500  sw-crypt: 0 ct-sta: 0'
 +[   31.926581] ath10k_ahb a800000.wifi: wmi print 'free: 53252 iram: 13432 sram: 35752'
 +[   32.190270] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-nvmem max-sta 32 raw 0 hwcrypto 1
 +[   32.323315] kmodloader: done loading kernel modules from /etc/modules.d/*
 +[   55.798151] ipqess-edma c080000.ethernet eth0: Link is Down
 +[   55.803293] ipqess-edma c080000.ethernet eth0: configuring for fixed/internal link mode
 +[   55.850711] ipqess-edma c080000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx
 +[   55.861417] qca8k-ipq4019 c000000.switch lan1: configuring for phy/psgmii link mode
 +[   56.046945] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
 +[   56.139009] br-lan: port 1(lan1) entered blocking state
 +[   56.212977] br-lan: port 1(lan1) entered disabled state
 +[   56.275908] device lan1 entered promiscuous mode
 +[   56.337873] device eth0 entered promiscuous mode
 +[   56.413594] qca8k-ipq4019 c000000.switch lan2: configuring for phy/psgmii link mode
 +[   56.454111] br-lan: port 2(lan2) entered blocking state
 +[   56.540063] br-lan: port 2(lan2) entered disabled state
 +[   56.602922] device lan2 entered promiscuous mode
 +[   56.673285] qca8k-ipq4019 c000000.switch lan3: configuring for phy/psgmii link mode
 +[   56.725404] br-lan: port 3(lan3) entered blocking state
 +[   56.811855] br-lan: port 3(lan3) entered disabled state
 +[   56.874738] device lan3 entered promiscuous mode
 +[   56.947003] qca8k-ipq4019 c000000.switch wan: configuring for phy/psgmii link mode
 +[   60.158327] qca8k-ipq4019 c000000.switch wan: Link is Up - 1Gbps/Full - flow control off
 +[   60.158415] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready
 +
 +
 +
 +BusyBox v1.36.1 (2024-04-17 05:04:46 UTC) built-in shell (ash)
 +
 +  _______                     ________        __
 +       |.-----.-----.-----.|  |  |  |.----.|  |_
 +     ||  _  |  -__|     ||  |  |  ||   _||   _|
 + |_______||   __|_____|__|__||________||__|  |____|
 +          |__| W I R E L E S S   F R E E D O M
 + -----------------------------------------------------
 + OpenWrt 23.05.3, r23809-234f1a2efa
 + -----------------------------------------------------
 +=== WARNING! =====================================
 +There is no root password defined on this device!
 +Use the "passwd" command to set up a new password
 +in order to prevent unauthorized SSH logins.
 +--------------------------------------------------
 +root@OpenWrt:/# cat /proc/mtd
 +dev:    size   erasesize  name
 +mtd0: 00040000 00010000 "sbl1"
 +mtd1: 00020000 00010000 "mibib"
 +mtd2: 00060000 00010000 "qsee"
 +mtd3: 00010000 00010000 "cdt"
 +mtd4: 00010000 00010000 "ddrparams"
 +mtd5: 00010000 00010000 "appsblenv"
 +mtd6: 00100000 00010000 "appsbl"
 +mtd7: 00010000 00010000 "ART"
 +mtd8: 00170000 00010000 "osss"
 +mtd9: 00010000 00010000 "pds"
 +mtd10: 00010000 00010000 "apcd"
 +mtd11: 00010000 00010000 "mfginfo"
 +mtd12: 00010000 00010000 "fcache"
 +mtd13: 00010000 00010000 "u-boot-env-bak"
 +mtd14: 00040000 00010000 "u-boot-env"
 +mtd15: 02000000 00020000 "aos0"
 +mtd16: 02000000 00020000 "aos1"
 +mtd17: 04000000 00020000 "ubi"
 +root@OpenWrt:/# ubinfo -a
 +UBI version:                    1
 +Count of UBI devices:           1
 +UBI control device major/minor: 10:126
 +Present UBI devices:            ubi0
 +
 +ubi0
 +Volumes count:                           4
 +Logical eraseblock size:                 126976 bytes, 124.0 KiB
 +Total amount of logical eraseblocks:     511 (64884736 bytes, 61.8 MiB)
 +Amount of available logical eraseblocks: 0 (0 bytes)
 +Maximum count of volumes                 128
 +Count of bad physical eraseblocks:       1
 +Count of reserved physical eraseblocks:  14
 +Current maximum erase counter value:     1
 +Minimum input/output unit size:          2048 bytes
 +Character device major/minor:            245:0
 +Present volumes:                         0, 1, 2, 3
 +
 +Volume ID:   0 (on ubi0)
 +Type:        dynamic
 +Alignment:   1
 +Size:        25 LEBs (3174400 bytes, 3.0 MiB)
 +State:       OK
 +Name:        kernel
 +Character device major/minor: 245:1
 +-----------------------------------
 +Volume ID:   1 (on ubi0)
 +Type:        dynamic
 +Alignment:   1
 +Size:        32 LEBs (4063232 bytes, 3.8 MiB)
 +State:       OK
 +Name:        rootfs
 +Character device major/minor: 245:2
 +-----------------------------------
 +Volume ID:   2 (on ubi0)
 +Type:        dynamic
 +Alignment:   1
 +Size:        431 LEBs (54726656 bytes, 52.1 MiB)
 +State:       OK
 +Name:        rootfs_data
 +Character device major/minor: 245:3
 +-----------------------------------
 +Volume ID:   3 (on ubi0)
 +Type:        dynamic
 +Alignment:   1
 +Size:        5 LEBs (634880 bytes, 620.0 KiB)
 +State:       OK
 +Name:        ubifs
 +Character device major/minor: 245:4
 +root@OpenWrt:/# mount
 +/dev/root on /rom type squashfs (ro,relatime,errors=continue)
 +proc on /proc type proc (rw,nosuid,nodev,noexec,noatime)
 +sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime)
 +cgroup2 on /sys/fs/cgroup type cgroup2 (rw,nosuid,nodev,noexec,relatime,nsdelegate)
 +tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
 +/dev/ubi0_2 on /overlay type ubifs (rw,noatime,assert=read-only,ubi=0,vol=2)
 +overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work)
 +tmpfs on /dev type tmpfs (rw,nosuid,noexec,noatime,size=512k,mode=755)
 +devpts on /dev/pts type devpts (rw,nosuid,noexec,noatime,mode=600,ptmxmode=000)
 +debugfs on /sys/kernel/debug type debugfs (rw,noatime)
 +bpffs on /sys/fs/bpf type bpf (rw,nosuid,nodev,noexec,noatime,mode=700)
 +root@OpenWrt:/# df -h
 +Filesystem                Size      Used Available Use% Mounted on
 +/dev/root                 4.0M      4.0M         0 100% /rom
 +tmpfs                   248.0M     64.0K    247.9M   0% /tmp
 +/dev/ubi0_2              46.5M    156.0K     43.9M   0% /overlay
 +overlayfs:/overlay       46.5M    156.0K     43.9M   0% /
 +tmpfs                   512.0K            512.0K   0% /dev
 +root@OpenWrt:/# 
 +root@OpenWrt:/# 
 +root@OpenWrt:/# 
 +root@OpenWrt:/# 
 +root@OpenWrt:/# 
 +</nowiki>
 +</WRAP>\\
  • Last modified: 2024/04/20 22:52
  • by ryanrs