ADB P.DG AV4202N

Devices with Broadcom WiFi chipsets have limited OpenWrt supportability (due to limited FLOSS driver availability for Broadcom chips). Consider this when choosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported. See Broadcom WiFi for details.

DSL will not work at all on devices with BCM63xx DSL chipset (due to unavailability of FLOSS driver for Broadcom chips). Consider this when choosing a device to buy, or when deciding to flash OpenWrt on your device because it is listed as supported.
See Broadcom DSL, Unsupported: DSL modem and Broadcom BCM63xx for details.

Original source code from ADB based on OpenWrt Kamikaze.

Other Names:

  • Centro grande Vx226N1
  • Pirelli PRG AV4202N

There is a version that supports fibreglass connection (the port being between the Ethernet ports and the phone port) maybe some unused pins are used in that version of the router, the original source code was supposed to also be for the router including this feature .

You must set your TCP/IP v4 protocol to:

  1. IP: 192.168.1.2
  2. Netmask: 255.255.255.0
  3. Gateway: 192.168.1.1
  4. DNS: (optional, can be blank).

Then:

  1. Power off the router.
  2. Press reset button near the antenna.
  3. Keep it pressed while powering up during ~20+ seconds.
  4. Browse to http://192.168.1.1/ and upload binary file.
  5. Wait until router reboots.
  1. Install tftpd server and configure virtual IP
    sudo su -
    apt-get install tftpd-hpa screen
    cd /var/lib/tftpboot
    wget  http://downloads.openwrt.org/snapshots/trunk/brcm63xx/openwrt-96368MVWG-generic-squashfs-cfe.bin
    cp openwrt-96368MVWG-generic-squashfs-cfe.bin bcm963xx_fs_kernel
    chmod 644 bcm963xx_fs_kernel
    /etc/init.d/tftpd-hpa restart
    ifconfig eth0:9 192.168.1.100 netmask 255.255.255.0
    # attach board eth0.1 to lan (second port, on the yellow block)
  2. plug usb to ttl cable
    cd
    screen -L /dev/ttyUSB0 115200,-parenb,-cstopb,cs8 #will generate a log file from session

    power on the router and press enter within 1 sec to get into CFE console

  3. Configure Router and Install Firmware

    CFE> help Available commands: testled test led command gpio gpio set value w Write the whole image start from beginning of the flash e Erase [m]ain Image or [r]ecovery Image or [n]vram or [p]SI or r Run program from flash image or from host depend on [f/h] flag p Print boot line and board parameter info c Change booline parameters f Write image to the flash i Erase persistent storage data b Change board parameters reset Reset the board flashimage Flashes a compressed image after the bootloader. help Obtain help for CFE commands For more information about a command, enter 'help command-name' *** command status = 0 CFE> p Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-6) : 96368_Swiss_S1 Number of MAC Addresses (1-32) : 16 Base MAC Address : 02:10:18:01:00:01 PSI Size (1-64) KBytes : 24 Main Thread Number [0|1] : 0 *** command status = 0 CFE> b Press: <enter> to use current value '-' to go previous parameter '.' to clear the current value 'x' to exit this command 96368VVW ------- 0 96368_SwissCom ------- 1 96368_Swiss_S1 ------- 2 96368MVWG ------- 3 96368SV2 ------- 4 96369PVG ------- 5 96368MBG ------- 6 Board Id (0-6) : 2 3 Number of MAC Addresses (1-32) : 16 Base MAC Address : 02:10:18:01:00:01 PSI Size (1-64) KBytes : 24 Main Thread Number [0|1] : 0 -- writeNvramData -- Resetting board... CFE version 1.0.37-102.6 [P2] for BCM96368 (32bit,SP,BE) Build Date: mer set 2 17:48:26 CEST 2009 ( root@TiglioLinux ) Copyright (C) 2000-2008 Broadcom Corporation. Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB CPU type 0x2A031: 400MHz, Bus: 160MHz, Ref: 64MHz CPU running TP0 Total memory: 67108864 bytes (64MB) Boot Address 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-6) : 96368MVWG Number of MAC Addresses (1-32) : 16 Base MAC Address : 02:10:18:01:00:01 PSI Size (1-64) KBytes : 24 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 1 web info: Waiting for connection on socket 0. CFE> CFE> e m Erasing Main Image (B8020000--B8C00000) CFE> f Loading 192.168.1.100:bcm963xx_fs_kernel ... Finished loading 3276804 bytes Increasing ...1 fs add: BFC10100 kadd: BFC10100 flash_rootfs_start_off20000 - rootfsOffset :10000 Increasing ...2 fs add: BFC20100 kadd: BFC20100 BOOT_OFFSET : F8400000 rootfsAddr : B8020100 kernelAddr : B8020100 Flashing root file system and kernel at 0xb8020000: Flashing newImgSize: 31FF04 remaining to flash ....... 00000004 . *** Image flash done *** ! Resetting board... CFE version 1.0.37-102.6 [P2] for BCM96368 (32bit,SP,BE) Build Date: mer set 2 17:48:26 CEST 2009 ( root@TiglioLinux ) Copyright (C) 2000-2008 Broadcom Corporation. Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB CPU type 0x2A031: 400MHz, Bus: 160MHz, Ref: 64MHz CPU running TP0 Total memory: 67108864 bytes (64MB) Boot Address 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.100 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 1 Board Id (0-6) : 96368MVWG Number of MAC Addresses (1-32) : 16 Base MAC Address : 02:10:18:01:00:01 PSI Size (1-64) KBytes : 24 Main Thread Number [0|1] : 0 *** Press any key to stop auto run (1 seconds) *** Auto run second count down: 0 Booting BRCM native image (0xb8020000) ...


Post Installation Tasks

vi /etc/config/network #--------------------
config interface 'lan'
       option ifname 'eth0.1'
       option type 'bridge'
       option proto 'static'
       option ipaddr '192.168.123.252'
       option netmask '255.255.255.0'
       option dns '192.168.123.50'
       option gateway '192.168.123.254'
       option ip6assign '60'
#-------------------------------------------

/etc/init.d/network restart

ping 192.168.123.254

opkg update

opkg install luci

/etc/init.d/uhttpd enable

/etc/init.d/uhttpd start

passwd #set root password
Architecture MIPS
Vendor Broadcom
bootloader cfe
Board ID 96368_Swiss_S1
System-On-Chip Broadcom BCM6368
cpu/Speed BMIPS4350 v3.1 / 2x 400 MHz BMIPS Dual Core
Flash-Chip Spansion S29GL128P
Flash size 16 MiB
RAM 64 MiB
Wireless BCM4322 802.11b/g/n
Ethernet Internal BCM6368 Switch
USB 2x USB2.0
Antenna 2x
Serial Yes
JTAG Yes

The top side of the PCB with removed shield and heatsink:

The bottom side:

port.serial General information about the serial port, serial port cable, etc.

The serial header is the J5 (below the heatsink) near the SoC. The pinout is the following:

RX GND 1 2 VCC GND 3 4 TX GND 5 6 J5

*** Press any key to stop auto run (1 seconds) *** Auto run second count down: 0 Booting BRCM native image (0xb8020000) ... Code Address: 0x80010000, Entry Address: 0x80010000 LZMA: Prossible old LZMA format, trying to decompress.. Flash Checksum control skipped ... Decompression OK! Entry at 0x80010000 Closing network. Disabling Switch ports. Flushing Receive Buffers... 3 buffers found. Closing DMA Channels. Starting program at 0x80010000 [ 0.000000] Linux version 3.10.21 (openwrt@snapon) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38999) ) #1 Sat Dec 7 21:10:29 PST 2013 [ 0.000000] Detected Broadcom 0x6368 CPU revision b2 [ 0.000000] CPU frequency is 400 MHz [ 0.000000] 64MB of RAM installed [ 0.000000] registering 38 GPIOs [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.0.37-102.6 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350) [ 0.000000] board_bcm963xx: board name: 96368MVWG [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 61240k/65536k available (2440k kernel code, 4296k reserved, 704k data, 244k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.000000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) [ 0.032000] pid_max: default: 32768 minimum: 301 [ 0.036000] Mount-cache hash table entries: 512 [ 0.044000] NET: Registered protocol family 16 [ 0.060000] registering PCI controller with io_map_base unset [ 0.064000] registering PCI controller with io_map_base unset [ 0.080000] bio: create slab <bio-0> at 0 [ 0.088000] PCI host bridge to bus 0000:00 [ 0.092000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 0.096000] pci_bus 0000:00: root bus resource [io 0x8000000-0x8007fff] [ 0.100000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.116000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff] [ 0.120000] PCI host bridge to bus 0000:01 [ 0.124000] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff] [ 0.128000] pci_bus 0000:01: root bus resource [io 0x8008000-0x800ffff] [ 0.132000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] [ 0.136000] pci 0000:01:1e.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.140000] pci 0000:01:1e.0: BAR 10: assigned [mem 0x38000000-0x3fffffff] [ 0.144000] pci 0000:01:1e.0: BAR 7: assigned [io 0x8008000-0x80080ff] [ 0.148000] pci 0000:01:1e.0: BAR 8: assigned [io 0x8008400-0x80084ff] [ 0.152000] pci 0000:01:1e.0: CardBus bridge to [bus 02-05] [ 0.156000] pci 0000:01:1e.0: bridge window [io 0x8008000-0x80080ff] [ 0.160000] pci 0000:01:1e.0: bridge window [io 0x8008400-0x80084ff] [ 0.164000] pci 0000:01:1e.0: bridge window [mem 0x38000000-0x3fffffff] [ 0.168000] PCI: Enabling device 0000:01:1e.0 (0000 -> 0003) [ 0.172000] Switching to clocksource MIPS [ 0.184000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) [ 0.212000] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08 [ 0.260000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0 [ 0.268000] NET: Registered protocol family 2 [ 0.276000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.284000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.288000] TCP: Hash tables configured (established 512 bind 512) [ 0.296000] TCP: reno registered [ 0.300000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.304000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.312000] NET: Registered protocol family 1 [ 0.320000] audit: initializing netlink socket (disabled) [ 0.328000] type=2000 audit(0.328:1): initialized [ 0.332000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.340000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.352000] msgmni has been set to 119 [ 0.356000] io scheduler noop registered [ 0.360000] io scheduler deadline registered (default) [ 0.368000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart [ 0.376000] console [ttyS0] enabled, bootconsole disabled [ 0.376000] console [ttyS0] enabled, bootconsole disabled [ 0.388000] bcm63xx-rng bcm63xx-rng: registered RNG driver [ 0.400000] physmap platform flash device: 08000000 at 18000000 [ 0.404000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 0.416000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.420000] Amd/Fujitsu Extended Query version 1.3. [ 0.428000] number of CFI chips: 1 [ 0.432000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368MVWG [ 0.440000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000 [ 0.444000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 11ff00 [ 0.452000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length ea0000 [ 0.460000] bcm63xxpart: Partition 3 is nvram offset fe0000 and length 20000 [ 0.468000] bcm63xxpart: Partition 4 is linux offset 20000 and length fc0000 [ 0.476000] bcm63xxpart: Spare partition is offset 340004 and length c9fffc [ 0.480000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0 [ 0.488000] Creating 5 MTD partitions on "physmap-flash.0": [ 0.496000] 0x000000000000-0x000000020000 : "CFE" [ 0.504000] 0x000000020100-0x000000140000 : "kernel" [ 0.508000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.524000] 0x000000140000-0x000000fe0000 : "rootfs" [ 0.536000] mtd: device 2 (rootfs) set to be root filesystem [ 0.540000] mtd: partition "rootfs_data" created automatically, ofs=0x340000, len=0xca0000 [ 0.548000] 0x000000340000-0x000000fe0000 : "rootfs_data" [ 0.560000] 0x000000fe0000-0x000001000000 : "nvram" [ 0.568000] 0x000000020000-0x000000fe0000 : "linux" [ 0.580000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542) [ 0.632000] b53_common: found switch: BCM63xx, rev 0 [ 0.640000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 0.652000] TCP: cubic registered [ 0.656000] NET: Registered protocol family 17 [ 0.660000] Bridge firewalling registered [ 0.664000] 8021q: 802.1Q VLAN Support v1.8 [ 0.684000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 0.696000] Freeing unused kernel memory: 244K (80323000 - 80360000) procd: Console is alive procd: - watchdog - procd: - preinit - ifconfig: SIOCGIFFLAGS: No such device Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.452000] Button Hotplug driver version 0.4.1 mount_root: jffs2 is not ready - EOF marker found ifconfig: SIOCGIFFLAGS: No such device procd: - early - procd: - watchdog - procd: - ubus - procd: - init - Please press Enter to activate this console. [ 11.560000] NET: Registered protocol family 10 [ 11.600000] nf_conntrack version 0.5.0 (960 buckets, 3840 max) [ 11.620000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 11.664000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093 [ 11.672000] Backport generated by backports.git backports-20130802-0-gdb67a3f [ 11.688000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.784000] xt_time: kernel timezone is -0000 [ 11.872000] cfg80211: Calling CRDA to update world regulatory domain [ 11.884000] cfg80211: World regulatory domain updated: [ 11.888000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 11.896000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 11.904000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 11.912000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 11.920000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 11.928000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 11.936000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) [ 12.124000] PPP generic driver version 2.4.2 [ 12.136000] NET: Registered protocol family 24 [ 12.196000] b43-phy0: Broadcom 43222 WLAN found (core revision 16) [ 12.248000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6 [ 12.280000] Broadcom 43xx driver loaded [ Features: PNL ] [ 19.160000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex [ 26.136000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 26.156000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 26.160000] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 27.304000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex [ 27.324000] device eth0.1 entered promiscuous mode [ 27.332000] device eth0 entered promiscuous mode [ 27.344000] br-lan: port 1(eth0.1) entered forwarding state [ 27.348000] br-lan: port 1(eth0.1) entered forwarding state [ 28.300000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 29.352000] br-lan: port 1(eth0.1) entered forwarding state


root@OpenWrt:/# cat /proc/mtd ############################# dev: size erasesize name mtd0: 00020000 00020000 "CFE" mtd1: 0011ff00 00020000 "kernel" mtd2: 00ea0000 00020000 "rootfs" mtd3: 00ca0000 00020000 "rootfs_data" mtd4: 00020000 00020000 "nvram" mtd5: 00fc0000 00020000 "linux" root@OpenWrt:/tmp/root# df ############################### Filesystem 1K-blocks Used Available Use% Mounted on rootfs 12928 1348 11580 10% / /dev/root 2048 2048 0 100% /rom tmpfs 30740 1052 29688 3% /tmp tmpfs 30740 8 30732 0% /tmp/root tmpfs 512 0 512 0% /dev /dev/mtdblock3 12928 1348 11580 10% /overlay overlayfs:/overlay 12928 1348 11580 10% / root@OpenWrt:/tmp/root# free ############################# total used free shared buffers Mem: 61484 21260 40224 0 1688 -/+ buffers: 19572 41912 Swap: 0 0 0 # demesg ################################################# root@OpenWrt:~# dmesg [ 0.000000] Linux version 3.10.21 (openwrt@snapon) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38999) ) #1 Sat Dec 7 21:10:29 PST 2013 [ 0.000000] Detected Broadcom 0x6368 CPU revision b2 [ 0.000000] CPU frequency is 400 MHz [ 0.000000] 64MB of RAM installed [ 0.000000] registering 38 GPIOs [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: 1.0.37-102.6 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a031 (Broadcom BMIPS4350) [ 0.000000] board_bcm963xx: board name: 96368MVWG [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] On node 0 totalpages: 16384 [ 0.000000] free_area_init_node: node 0, pgdat 8030cc20, node_mem_map 81000000 [ 0.000000] Normal zone: 128 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 16384 pages, LIFO batch:3 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: [0] 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Memory: 61240k/65536k available (2440k kernel code, 4296k reserved, 704k data, 244k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.028000] Calibrating delay loop... 397.82 BogoMIPS (lpj=795648) [ 0.032000] pid_max: default: 32768 minimum: 301 [ 0.036000] Mount-cache hash table entries: 512 [ 0.044000] NET: Registered protocol family 16 [ 0.060000] registering PCI controller with io_map_base unset [ 0.064000] registering PCI controller with io_map_base unset [ 0.080000] bio: create slab <bio-0> at 0 [ 0.088000] PCI host bridge to bus 0000:00 [ 0.092000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff] [ 0.096000] pci_bus 0000:00: root bus resource [io 0x8000000-0x8007fff] [ 0.100000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.104000] pci 0000:00:01.0: [14e4:a8d6] type 00 class 0x028000 [ 0.104000] pci 0000:00:01.0: reg 10: [mem 0x00000000-0x00003fff] [ 0.116000] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 00 [ 0.116000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30003fff] [ 0.120000] PCI host bridge to bus 0000:01 [ 0.124000] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff] [ 0.128000] pci_bus 0000:01: root bus resource [io 0x8008000-0x800ffff] [ 0.132000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff] [ 0.136000] pci 0000:01:1e.0: [14e4:6368] type 02 class 0x060700 [ 0.136000] pci 0000:01:1e.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.140000] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 05 [ 0.140000] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 05 [ 0.140000] pci 0000:01:1e.0: BAR 10: assigned [mem 0x38000000-0x3fffffff] [ 0.144000] pci 0000:01:1e.0: BAR 7: assigned [io 0x8008000-0x80080ff] [ 0.148000] pci 0000:01:1e.0: BAR 8: assigned [io 0x8008400-0x80084ff] [ 0.152000] pci 0000:01:1e.0: CardBus bridge to [bus 02-05] [ 0.156000] pci 0000:01:1e.0: bridge window [io 0x8008000-0x80080ff] [ 0.160000] pci 0000:01:1e.0: bridge window [io 0x8008400-0x80084ff] [ 0.164000] pci 0000:01:1e.0: bridge window [mem 0x38000000-0x3fffffff] [ 0.168000] PCI: Enabling device 0000:01:1e.0 (0000 -> 0003) [ 0.172000] pci 0000:01:1e.0: setting latency timer to 64 [ 0.172000] Switching to clocksource MIPS [ 0.184000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002) [ 0.192000] b43-pci-bridge 0000:00:01.0: setting latency timer to 64 [ 0.212000] ssb: Found chip with id 0xA8D6, rev 0x00 and package 0x08 [ 0.220000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x1E, vendor 0x4243) [ 0.220000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x10, vendor 0x4243) [ 0.220000] ssb: Core 2 found: PCI (cc 0x804, rev 0x0E, vendor 0x4243) [ 0.260000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0 [ 0.268000] NET: Registered protocol family 2 [ 0.276000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.284000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.288000] TCP: Hash tables configured (established 512 bind 512) [ 0.296000] TCP: reno registered [ 0.300000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.304000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.312000] NET: Registered protocol family 1 [ 0.316000] PCI: CLS 0 bytes, default 16 [ 0.320000] audit: initializing netlink socket (disabled) [ 0.328000] type=2000 audit(0.328:1): initialized [ 0.332000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.340000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.352000] msgmni has been set to 119 [ 0.356000] io scheduler noop registered [ 0.360000] io scheduler deadline registered (default) [ 0.368000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 10) is a bcm63xx_uart [ 0.376000] console [ttyS0] enabled, bootconsole disabled [ 0.388000] bcm63xx-rng bcm63xx-rng: registered RNG driver [ 0.400000] physmap platform flash device: 08000000 at 18000000 [ 0.404000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x0000c2 Chip ID 0x00227e [ 0.416000] physmap-flash.0: Found an alias at 0x1000000 for the chip at 0x0 [ 0.416000] Amd/Fujitsu Extended Query Table at 0x0040 [ 0.420000] Amd/Fujitsu Extended Query version 1.3. [ 0.428000] number of CFI chips: 1 [ 0.432000] bcm63xxpart: CFE boot tag found with version 6 and board type 96368MVWG [ 0.440000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000 [ 0.444000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 11ff00 [ 0.452000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length ea0000 [ 0.460000] bcm63xxpart: Partition 3 is nvram offset fe0000 and length 20000 [ 0.468000] bcm63xxpart: Partition 4 is linux offset 20000 and length fc0000 [ 0.476000] bcm63xxpart: Spare partition is offset 340004 and length c9fffc [ 0.480000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0 [ 0.488000] Creating 5 MTD partitions on "physmap-flash.0": [ 0.496000] 0x000000000000-0x000000020000 : "CFE" [ 0.504000] 0x000000020100-0x000000140000 : "kernel" [ 0.508000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.524000] 0x000000140000-0x000000fe0000 : "rootfs" [ 0.536000] mtd: device 2 (rootfs) set to be root filesystem [ 0.540000] mtd: partition "rootfs_data" created automatically, ofs=0x340000, len=0xca0000 [ 0.548000] 0x000000340000-0x000000fe0000 : "rootfs_data" [ 0.560000] 0x000000fe0000-0x000001000000 : "nvram" [ 0.568000] 0x000000020000-0x000000fe0000 : "linux" [ 0.580000] bcm63xx-spi bcm63xx-spi: at 0xb0000800 (irq 9, FIFOs size 542) [ 0.632000] b53_common: found switch: BCM63xx, rev 0 [ 0.640000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 0.652000] TCP: cubic registered [ 0.656000] NET: Registered protocol family 17 [ 0.660000] Bridge firewalling registered [ 0.664000] 8021q: 802.1Q VLAN Support v1.8 [ 0.684000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 0.696000] Freeing unused kernel memory: 244K (80323000 - 80360000) [ 7.452000] Button Hotplug driver version 0.4.1 [ 11.560000] NET: Registered protocol family 10 [ 11.600000] nf_conntrack version 0.5.0 (960 buckets, 3840 max) [ 11.620000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 11.664000] Loading modules backported from Linux version master-2013-11-05-0-gafa3093 [ 11.672000] Backport generated by backports.git backports-20130802-0-gdb67a3f [ 11.688000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.784000] xt_time: kernel timezone is -0000 [ 11.872000] cfg80211: Calling CRDA to update world regulatory domain [ 11.884000] cfg80211: World regulatory domain updated: [ 11.888000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 11.896000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 11.904000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 11.912000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 11.920000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 11.928000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (300 mBi, 2000 mBm) [ 11.936000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm) [ 12.124000] PPP generic driver version 2.4.2 [ 12.136000] NET: Registered protocol family 24 [ 12.196000] b43-phy0: Broadcom 43222 WLAN found (core revision 16) [ 12.248000] b43-phy0: Found PHY: Analog 8, Type 4 (N), Revision 6 [ 12.280000] Broadcom 43xx driver loaded [ Features: PNL ] [ 12.288000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 19.160000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex [ 26.136000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 26.156000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 27.304000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex [ 27.324000] device eth0.1 entered promiscuous mode [ 27.332000] device eth0 entered promiscuous mode [ 27.344000] br-lan: port 1(eth0.1) entered forwarding state [ 27.348000] br-lan: port 1(eth0.1) entered forwarding state [ 28.300000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 29.352000] br-lan: port 1(eth0.1) entered forwarding state [ 26.160000] jffs2_build_filesystem(): erasing all blocks after the end marker... done. [ 107.348000] jffs2: notice: (562) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 184.508000] br-lan: port 1(eth0.1) entered disabled state [ 184.524000] device eth0.1 left promiscuous mode [ 184.528000] device eth0 left promiscuous mode [ 184.532000] br-lan: port 1(eth0.1) entered disabled state [ 186.496000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex [ 188.612000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on port2, 100Mbps, full-duplex [ 188.624000] device eth0.1 entered promiscuous mode [ 188.628000] device eth0 entered promiscuous mode [ 188.636000] br-lan: port 1(eth0.1) entered forwarding state [ 188.640000] br-lan: port 1(eth0.1) entered forwarding state [ 189.608000] IPv6: ADDRCONF(NETDEV_CHANGE): eth0.1: link becomes ready [ 190.644000] br-lan: port 1(eth0.1) entered forwarding state


  • The MiniPCI connector
  • The U22 IC seems to be a SPI flash in SO16 wide package with this pinout:

  • There is an unpopulated WAN port right to the LAN ports. Population options are present for two different media interface, but with the same pinout PHY in QFN32 package. (U7 on the top, and U4 on the bottom.) These PHYs looks like an MII PHY, but I have not found a pin compatible yet.

The know pins can be seen on the following picture: (the P$[N] pins are unknown)

If you know a pin compatible one, please let us know.

  • Unpopulated Smartcard reader.
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1