Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
Next revisionBoth sides next revision
toh:adb:p.dg_a4001n1 [2014/05/19 01:35] ralloditoh:adb:p.dg_a4001n1 [2019/02/12 22:20] – 432 warning added tmomas
Line 1: Line 1:
 +====== ADB P.DG A4001N1 ======
  
 +{{section>meta:infobox:432_warning#infobox_for_dataentries&noheader&nofooter&noeditbutton}}
 +{{section>meta:infobox:broadcom_dsl#infobox_for_dataentries&noheader&nofooter&noeditbutton}}
 +
 +===== Supported Versions =====
 +---- datatable ----
 +cols    : Model, Versions, Supported Current Rel, OEM device homepage URL_url, OWrt Forum Topic URL_url, Device Techdata_pageid
 +headers : Model, Version, Current Release, OEM Info, Forum Topic, Technical Data
 +align   : c,c,c,c,c,c,c
 +filter  : Model=P.DG A4001N1
 +----
 +
 +
 +===== Hardware Highlights =====
 +---- datatable ----
 +cols    : Model, Versions, CPU, CPU MHz, Flash MB_mbflashs, RAM MB_mbram, WLAN Hardware, WLAN 2.4GHz, WLAN 5.0GHz, Ethernet 100M ports_, Ethernet Gbit ports_, Modem, USB ports_
 +header  : Model, Version,SoC,CPU MHz,Flash MB,RAM MB,WLAN Hardware,WLAN2.4,WLAN5.0,100M ports,Gbit ports,Modem,USB
 +align   : c,c,c,c,c,c,c,c,c,c,c,c,c
 +filter  : Model=P.DG A4001N1
 +----
 +
 +
 +===== Installation =====
 +---- datatable ----
 +cols    : Model, Versions, Supported Current Rel, Firmware OpenWrt Install URL_url, Firmware OpenWrt Upgrade URL_url, Firmware OEM Stock URL_url
 +headers : Model, Version, Current Release, Firmware OpenWrt Install, Firmware OpenWrt Upgrade, Firmware OEM Stock
 +align   : c,c,c
 +filter  : Model=P.DG A4001N1
 +----
 +
 +==== Flashing ANY Firmware ====
 +You must set your TCP/IP v4 protocol to:
 +  - IP: 192.168.1.2
 +  - Netmask: 255.255.255.0
 +  - Gateway: 192.168.1.1
 +  - DNS: (optional, can be blank).
 +
 +Option 1: Works if flashing from the original firmware from telefonica. Access:
 +  - ''%%http://192.168.1.1/main.html%%''
 +  - username 1234
 +  - password 1234
 +  - select update firmware and proceed
 +
 +Option 2 (does not always work):
 +  - Power off the router.
 +  - Press reset button near the antenna.
 +  - Keep it pressed while powering up during ~20+ seconds.
 +  - Acces to ''%%http://192.168.1.1%%'' and upload binary file.
 +  - Wait until router reboots.
 +
 +===== Hardware =====
 +==== Info ====
 +^ [[wp>Instruction set|Architecture]]  | [[wp>MIPS architecture|MIPS]]   |
 +^ Vendor                               | [[wp>Broadcom]]                 |
 +^ [[docs:techref:bootloader]]          | [[docs:techref:bootloader:cfe]]  |
 +^ Bootloader version                   | 1.0.37-106.24                   |
 +^ [[docs:techref:hardware:soc|System-On-Chip]]  | Broadcom BCM6328          |
 +^ [[docs:techref:hardware:cpu|CPU]]/Speed       | BMIPS4350 v7.5 / 320 MHz  |
 +^ Board ID        | 963281T_TEF                       |
 +^ Flash-Chip      | MX25L128                          |
 +^ Flash size      | 16 MiB                            |
 +^ RAM             | 32 MiB                            |
 +^ Wireless        | BCM43225 (14e4:a8d8) 802.11b/g/ |
 +^ Wireless power  | ? mW                              |
 +^ Ethernet        | Internal BRCM6328 Switch          |
 +^ USB             | yes    |
 +^ Power adapter   | ?      |
 +^ Power margin    | ?      |
 +^ Antenna         | 2x     |
 +^ Antenna gain    | ? dBi  |
 +^ [[docs:techref:hardware:port.serial|Serial]]  | [[#Serial|Yes]]  |
 +^ [[docs:techref:hardware:port.jtag|JTAG]]      | [[#JTAG|?]]      |
 +
 +==== Photos ====
 +=== Router ===
 +{{:media:adb:a4001n1.jpg?400}}
 +
 +==== JTAG ====
 +-> [[docs:techref:hardware:port.jtag]] general information about the JTAG port, JTAG cable, etc.
 +
 +N/A
 +
 +==== Serial ====
 +-> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc.
 +
 +How to connect to the Serial Port of this specific device:\\
 +{{:media:adb:a4001n1_serial.jpg?400}}
 +
 +===== GPIO =====
 +==== LEDs ====
 +Read: [[docs:guide-user:base-system:led_configuration|System configuration: Leds]] to configure the leds
 +^ Pin   ^ Event       ^ Active   ^
 +| 4     | power       | Low      |
 +| 8     | stop        | Low      |
 +| 11    | inet        | Low      |
 +| 2     | inet-fail   | Low      |
 +| 3     | ppp         | Low      |
 +| 5     | ppp-fail    | Low      |
 +| 6     | 3g          | Low      |
 +| 7     | 3g-fail     | Low      |
 +| 9     | wlan        | Low      |
 +| 10    | wlan-fail   | Low      |
 +| 31    | eth         | Low      |
 +| 20    | eth-fail    | Low      |
 +
 +==== Buttons ====
 +-> [[docs:guide-user:hardware:hardware.button]] on howto use and configure the hardware button(s).
 +^ Pin   ^ Event   ^ Active   ^
 +| 23    | reset   | Low      |
 +| 24    | wlan    | Low      |
 +
 +
 +
 +===== Bootlogs =====
 +==== OEM Bootlog ====
 +<WRAP bootlog>
 +<nowiki>CFE version 1.0.37-106.24 for A4001N TEF 0002 BCM96328 (32bit,SP,BE)
 +Build Date: Wed Jan 26 12:59:25 CET 2011 (zu1costast@thorold)
 +Copyright (C) 2000-2009 Broadcom Corporation.
 +
 +HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
 +Total Flash size: 16384K with 4096 sectors
 +Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
 +Main Thread: TP0
 +Memory Test Passed
 +Total Memory: 33554432 bytes (32MB)
 +Boot Address: 0xb8000000
 +
 +Board IP address                  : 192.168.1.1:ffffff00  
 +Host IP address                   : 192.168.1.10  
 +Gateway IP address                :   
 +Run from flash/host (f/h)         : f  
 +Default host run file name        : run.bin  
 +Default host flash file name      : 2.bin  
 +Boot delay (0-9 seconds)          : 9  
 +Board Id (0-4)                    : 963281T_TEF  
 +Number of MAC Addresses (1-32)    : 11  
 +Base MAC Address                  : 11:22:33:44:55:66  
 +PSI Size (1-64) KBytes            : 24  
 +Enable Backup PSI [0|1]           : 1  
 +System Log Size (0-256) KBytes    : 0  
 +Main Thread Number [0|1]          : 0  
 +Voice Board Configuration (0-11)  :   
 +
 +*** Press any key to stop auto run (9 seconds) ***
 +Auto run second count down: 9
 +web info: Waiting for connection on socket 0.
 +web info: Waiting for connection on socket 1.
 +web info: Waiting for connection on socket 2.
 +web info: Waiting for connection on socket 0.
 +web info: Waiting for connection on socket 1.
 +web info: Upload 6818609 bytes, Broadcom image format.
 +web info: Waiting for connection on socket 0.
 +
 +Flashing root file system and kernel at 0xb8800000: .....................................................
 +
 +.
 +*** Image flash done *** !
 +
 +Resetting board...HELO
 +CPUI
 +L1CI
 +DRAM
 +----
 +PHYS
 +ZQDN
 +PHYE
 +DINT
 +LSYN
 +USYN
 +MSYN
 +LMBE
 +PASS
 +----
 +ZBSS
 +CODE
 +DATA
 +L12F
 +MAIN
 +
 +
 +CFE version 1.0.37-106.24 for A4001N TEF 0002 BCM96328 (32bit,SP,BE)
 +Build Date: Wed Jan 26 12:59:25 CET 2011 (zu1costast@thorold)
 +Copyright (C) 2000-2009 Broadcom Corporation.
 +
 +HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
 +Total Flash size: 16384K with 4096 sectors
 +Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
 +Main Thread: TP0
 +Memory Test Passed
 +Total Memory: 33554432 bytes (32MB)
 +Boot Address: 0xb8000000
 +
 +Board IP address                  : 192.168.1.1:ffffff00  
 +Host IP address                   : 192.168.1.10  
 +Gateway IP address                :   
 +Run from flash/host (f/h)         : f  
 +Default host run file name        : run.bin  
 +Default host flash file name      : 2.bin  
 +Boot delay (0-9 seconds)          : 9  
 +Boot image (0=latest, 1=previous) : 0  
 +Board Id (0-4)                    : 963281T_TEF  
 +Number of MAC Addresses (1-32)    : 11  
 +Base MAC Address                  : 11:22:33:44:55:66  
 +PSI Size (1-64) KBytes            : 24  
 +Enable Backup PSI [0|1]           : 1  
 +System Log Size (0-256) KBytes    : 0  
 +Main Thread Number [0|1]          : 0  
 +Voice Board Configuration (0-11)  :   
 +
 +*** Press any key to stop auto run (9 seconds) ***
 +Auto run second count down: 0
 +Booting from latest image (0xb8800000) ...
 +Code Address: 0x80010000, Entry Address: 0x80014230
 +Decompression OK!
 +Entry at 0x80014230
 +Closing network.
 +Disabling Switch ports.
 +Flushing Receive Buffers...
 +0 buffers found.
 +Closing DMA Channels.
 +Starting program at 0x80014230
 +Linux version 2.6.30 (zu1costast@thorold) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Thu Apr 21 20:1
 +HS Serial flash device: name MX25L128, id 0xc218 size 16384KB
 +963281T_TEF prom init
 +CPU revision is: 0002a075 (Broadcom4350)
 +Determined physical RAM map:
 + memory: 01f00000 @ 00000000 (usable)
 +Zone PFN ranges:
 +  DMA      0x00000000 -> 0x00001000
 +  Normal   0x00001000 -> 0x00001f00
 +Movable zone start PFN for each node
 +early_node_map[1] active PFN ranges
 +    0: 0x00000000 -> 0x00001f00
 +On node 0 totalpages: 7936
 +free_area_init_node: node 0, pgdat 802f3830, node_mem_map 81000000
 +  DMA zone: 32 pages used for memmap
 +  DMA zone: 0 pages reserved
 +  DMA zone: 4064 pages, LIFO batch:0
 +  Normal zone: 30 pages used for memmap
 +  Normal zone: 3810 pages, LIFO batch:0
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 7874
 +Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
 +wait instruction: enabled
 +Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
 +Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +RCU-based detection of stalled CPUs is enabled.
 +NR_IRQS:128
 +PID hash table entries: 128 (order: 7, 512 bytes)
 +console [ttyS0] enabled
 +Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
 +Memory: 28088k/31744k available (2409k kernel code, 3656k reserved, 555k data, 120k init, 0k highmem)
 +Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
 +Mount-cache hash table entries: 512
 +net_namespace: 536 bytes
 +NET: Registered protocol family 16
 +Total Flash size: 16384K with 4096 sectors
 +registering PCI controller with io_map_base unset
 +registering PCI controller with io_map_base unset
 +bio: create slab <bio-0> at 0
 +SCSI subsystem initialized
 +usbcore: registered new interface driver usbfs
 +usbcore: registered new interface driver hub
 +usbcore: registered new device driver usb
 +pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]
 +pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]
 +pci 0000:01:00.0: PME# supported from D0 D3hot
 +pci 0000:01:00.0: PME# disabled
 +pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
 +pci 0000:02:00.0: supports D1 D2
 +pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
 +pci 0000:01:00.0:   IO window: disabled
 +pci 0000:01:00.0:   MEM window: 0x10f00000-0x10ffffff
 +pci 0000:01:00.0:   PREFETCH window: disabled
 +PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:01:00.0 to 64
 +BLOG v2.1 Initialized
 +NET: Registered protocol family 8
 +NET: Registered protocol family 20
 +NET: Registered protocol family 2
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 1024 (order: 1, 8192 bytes)
 +TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP: Hash tables configured (established 1024 bind 1024)
 +TCP reno registered
 +NET: Registered protocol family 1
 +squashfs: version 4.0 (2009/01/31) Phillip Lougher
 +squashfs: version 4.0 with LZMA457 ported by BRCM
 +fuse init (API version 7.11)
 +msgmni has been set to 54
 +io scheduler noop registered (default)
 +pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check vendor BIOS
 +PCI: Setting latency timer of device 0000:01:00.0 to 64
 +Driver 'sd' needs updating - please use bus_type methods
 +PPP generic driver version 2.4.2
 +PPP Deflate Compression module registered
 +PPP BSD Compression module registered
 +NET: Registered protocol family 24
 +bcm963xx_mtd driver v1.0
 +File system address: 0xb8800100
 +ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
 +PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:00:0a.0 to 64
 +ehci_hcd 0000:00:0a.0: EHCI Host Controller
 +ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
 +ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
 +ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500
 +ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
 +usb usb1: configuration #1 chosen from 1 choice
 +hub 1-0:1.0: USB hub found
 +hub 1-0:1.0: 1 port detected
 +ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
 +PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:00:09.0 to 64
 +ohci_hcd 0000:00:09.0: OHCI Host Controller
 +ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
 +ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
 +usb usb2: configuration #1 chosen from 1 choice
 +hub 2-0:1.0: USB hub found
 +hub 2-0:1.0: 1 port detected
 +usbcore: registered new interface driver usblp
 +Initializing USB Mass Storage driver...
 +usbcore: registered new interface driver usb-storage
 +USB Mass Storage support registered.
 +brcmboard: brcm_board_init entry
 +SES: Button Interrupt 0x1 is enabled
 +SES: LED GPIO 0x8009 is enabled
 +initLed: led[0]: Gpio=0xffff8003, FailGpio=0xffff8005
 +initLed: led[1]: Gpio=0xffffffff, FailGpio=0xffffffff
 +initLed: led[2]: Gpio=0xffffffff, FailGpio=0xffffffff
 +initLed: led[3]: Gpio=0xffff800b, FailGpio=0xffff8002
 +initLed: led[4]: Gpio=0xffff8009, FailGpio=0xffff800a
 +initLed: led[5]: Gpio=0xffffffff, FailGpio=0xffffffff
 +initLed: led[6]: Gpio=0xffffffff, FailGpio=0xffffffff
 +initLed: led[7]: Gpio=0xffff8006, FailGpio=0xffff8007
 +initLed: led[8]: Gpio=0xffffffff, FailGpio=0xffffffff
 +initLed: led[9]: Gpio=0xffffffff, FailGpio=0xffffffff
 +initLed: led[10]: Gpio=0xffffffff, FailGpio=0xffffffff
 +initLed: led[11]: Gpio=0xffffffff, FailGpio=0xffffffff
 +initLed: led[12]: Gpio=0xffffffff, FailGpio=0xffffffff
 +initLed: led[13]: Gpio=0xffff8004, FailGpio=0xffff8008
 +initLed: led[14]: Gpio=0xffff8006, FailGpio=0xffff8007
 +initLed: led[15]: Gpio=0xffff801f, FailGpio=0xffff8014
 +Serial: BCM63XX driver $Revision: 3.00 $
 +ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
 +ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX
 +bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Apr 21 2011 20:07:12
 +Broadcom Logger v0.1 Apr 21 2011 20:04:59
 +Mirror/redirect action on
 +u32 classifier
 +    input device check on 
 +    Actions configured 
 +TCP cubic registered
 +NET: Registered protocol family 17
 +Initializing MCPD Module
 +Ebtables v2.0 registered
 +ebt_time registered
 +ebt_ftos registered
 +ebt_wmm_mark registered
 +802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
 +All bugs added by David S. Miller <davem@redhat.com>
 +VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
 +Freeing unused kernel memory: 120k freed
 +init started:  BusyBox v1.00 (2011.04.21-18:13+0000) multi-call binary
 +
 +
 +BusyBox v1.00 (2011.04.21-18:13+0000) Built-in shell (ash)
 +Enter 'help' for a list of built-in commands.
 +
 +
 +Loading drivers and kernel modules... 
 +
 +bcmxtmcfg: module license 'Proprietary' taints kernel.
 +Disabling lock debugging due to kernel taint
 +bcmxtmcfg: bcmxtmcfg_init entry
 +adsl: adsl_init entry
 +Broadcom BCM6328B0 Ethernet Network Device v0.1 Apr 21 2011 20:05:03
 +ETH Init: 180 tx BDs at 0xa194e000
 +ETH Init: 400 rx BDs at 0xa19f8000
 +ETH Init: 400 rx BDs at 0xa19f9000
 +dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered 
 +eth0: MAC Address: 11:22:33:44:55:66
 +eth1: MAC Address: 11:22:33:44:55:66
 +eth2: MAC Address: 11:22:33:44:55:66
 +eth3: MAC Address: 11:22:33:44:55:66
 +eth0 Link UP 100 mbps full duplex
 +message received before monitor task is initialized kerSysSendtoMonitorTask 
 +BCM63XX_USB USB Device not present
 +insmod: cannot insert `/lib/modules/2.6.30/extra/bcm_usb.ko': Success (19): Success
 +PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
 +PCI: Setting latency timer of device 0000:02:00.0 to 64
 +wl:srom not detected,using main memory mapped srom info(wombo board)
 +wl:loading /etc/wlan/bcm43225_map.bin
 +wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.60.120.1.cpePDG_TEF_SP_4.06L4.2
 +dgasp: kerSysRegisterDyingGaspHandler: wl0 registered 
 +Auto-negotiation enabled.
 +The autonegotiated media type is 100baseTx-FD.
 +Link is up
 +mii register 26 is 0x4000
 +
 +===== Release Version PDG_TEF_SP_4.06L.4 (build timestamp 110421_2011) =====
 +
 +factoryCfg = 0
 +iptables v1.4.0: can't initialize iptables table `nat': iptables who? (do you need to insmod?)
 +Perhaps iptables or your kernel needs to be upgraded.
 +sendto: Network is unreachable
 +ip_tables: (C) 2000-2006 Netfilter Core Team
 +device eth0 entered promiscuous mode
 +br0: port 1(eth0) entering forwarding state
 +device eth1 entered promiscuous mode
 +device eth2 entered promiscuous mode
 +device eth3 entered promiscuous mode
 +device wl0 entered promiscuous mode
 +br0: port 5(wl0) entering forwarding state
 +ssk:error:23.000:BcmAdsl_Initialize=0xC00A50D8, g_pFnNotifyCallback=0xC00D5E04
 +rutDsl_CfgProfileInit:2015:rutDsl_CfgProfileInit()
 +WLmngr Daemon is running
 +optarg=0 shmId=0 
 +wlevt_init@107: opened loopback socket 4
 +wlevt is ready for new msg...
 +pSdramPHY=0xA1FFFFF8, 0x840002 0x40099
 +AdslCoreSharedMemInit: shareMemAvailable=484928
 +AdslCoreHwReset:  AdslOemDataAddr = 0xA1F6AEB4
 +dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered 
 +XTM Init: 400 rx BDs at 0xa0bb5000
 +XTM Init: 100 rx BDs at 0xa0b12000
 +Netfilter messages via NETLINK v0.30.
 +nf_conntrack version 0.5.0 (496 buckets, 1984 max)
 +iptables: No chain/target/match by that name
 +monitor task is initialized pid= 244 
 +There is no Predefined DevicePin in CFE
 +WPS Device PIN = 29942275
 +backup_psi_number_blk=6 result=24576
 +device wl0 left promiscuous mode
 +br0: port 5(wl0) entering disabled state
 +device wl0 entered promiscuous mode
 +br0: port 5(wl0) entering forwarding state
 +backup_psi_number_blk=6 result=24576
 +Setting SSID: "ESRO2"
 +Setting SSID: "wlwl0.1 (): not using net_device_ops yet
 +0_Guest1"
 +Setting SSID: "wlwl0.2 (): not using net_device_ops yet
 +0_Guest2"
 +Setting SSID: "wlwl0.3 (): not using net_device_ops yet
 +0_Guest3"
 +br0: port 5(wl0) entering disabled state
 +wlctl: Unsupported
 +wlctl: Unsupported
 +wlctl: Unsupported
 +wlctl: Undefined error
 +chanspec 0x2b01 selected 
 +device wl0 left promiscuous mode
 +br0: port 5(wl0) entering disabled state
 +device wl0 entered promiscuous mode
 +br0: port 5(wl0) entering forwarding state
 +Reaped 1381
 +UPnP daemon is ready to run</nowiki>
 +</WRAP>\\
 +
 +==== Openwrt Bootlog ====
 +<WRAP bootlog>
 +<nowiki>   0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #4 Mon Jun 25 11:34:01 CEST 2012
 +[    0.000000] Detected Broadcom 0x6328 CPU revision 10b0
 +[    0.000000] CPU frequency is 320 MHz
 +[    0.000000] 32MB of RAM installed
 +[    0.000000] registering 32 GPIOs
 +[    0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: bcm63xx-gpio
 +[    0.000000] board_bcm963xx: Boot address 0xb8000000
 +[    0.000000] board_bcm963xx: CFE version: A4001N-V0003
 +[    0.000000] bootconsole [early0] enabled
 +[    0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
 +[    0.000000] board_bcm963xx: board name: 963281T_TEF
 +[    0.000000] Determined physical RAM map:
 +[    0.000000]  memory: 02000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone PFN ranges:
 +[    0.000000]   Normal   0x00000000 -> 0x00002000
 +[    0.000000] Movable zone start PFN for each node
 +[    0.000000] Early memory PFN ranges
 +[    0.000000]     0: 0x00000000 -> 0x00002000
 +[    0.000000] On node 0 totalpages: 8192
 +[    0.000000] free_area_init_node: node 0, pgdat 802a39f0, node_mem_map 81000000
 +[    0.000000]   Normal zone: 64 pages used for memmap
 +[    0.000000]   Normal zone: 0 pages reserved
 +[    0.000000]   Normal zone: 8128 pages, LIFO batch:0
 +[    0.000000] Reserving 0MB of memory at 0MB for crashkernel
 +[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
 +[    0.000000] pcpu-alloc:
 +0
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
 +[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
 +[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
 +[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
 +[    0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
 +[    0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +[    0.000000] Memory: 29384k/32768k available (2240k kernel code, 3384k reserved, 400k data, 200k init, 0k highmem)
 +[    0.000000] NR_IRQS:128
 +[    0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928)
 +[    0.036000] pid_max: default: 32768 minimum: 301
 +[    0.040000] Mount-cache hash table entries: 512
 +[    0.048000] NET: Registered protocol family 16
 +[    0.280000] registering PCI controller with io_map_base unset
 +[    0.288000] bio: create slab <bio-0> at 0
 +[    0.292000] PCI host bridge to bus 0000:00
 +[    0.296000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff]
 +[    0.300000] pci_bus 0000:00: root bus resource [ 0x00000000 flags 0x0]
 +[    0.304000] pci 0000:00:00.0: [14e4:6328] type 1 class 0x000604
 +[    0.304000] pci 0000:00:00.0: PME# supported from D0 D3hot
 +[    0.304000] pci 0000:01:00.0: [14e4:a8d8] type 0 class 0x000280
 +[    0.304000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00003fff 64bit]
 +[    0.304000] pci 0000:01:00.0: supports D1 D2
 +[    0.304000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff]
 +[    0.308000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit]
 +[    0.312000] pci 0000:00:00.0: PCI bridge to [bus 01-01]
 +[    0.316000] pci 0000:00:00.0:   bridge window [mem 0x10f00000-0x10ffffff]
 +[    0.320000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002)
 +[    0.324000] Switching to clocksource MIPS
 +[    0.332000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
 +[    0.340000] bcma: Found chip with id 0xA8D9, rev 0x01 and package 0x0A
 +[    0.344000] bcma: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0)
 +[    0.352000] bcma: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0)
 +[    0.360000] bcma: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0)
 +[    0.444000] bcma: Failed to get SPROM: -71
 +[    0.452000] bcma: Bus registered
 +[    0.456000] NET: Registered protocol family 2
 +[    0.460000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.468000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
 +[    0.476000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.480000] TCP: Hash tables configured (established 1024 bind 1024)
 +[    0.488000] TCP reno registered
 +[    0.492000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.496000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.504000] NET: Registered protocol family 1
 +[    0.508000] PCI: CLS 0 bytes, default 16
 +[    0.512000] audit: initializing netlink socket (disabled)
 +[    0.516000] type=2000 audit(0.516:1): initialized
 +[    0.524000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
 +[    0.528000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.540000] msgmni has been set to 57
 +[    0.544000] io scheduler noop registered
 +[    0.548000] io scheduler deadline registered (default)
 +[    0.556000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart
 +[    0.564000] console [ttyS0] enabled, bootconsole disabled
 +[    0.580000] m25p80 spi0.0: found mx25l12805d, expected m25p80
 +[    0.588000] m25p80 spi0.0: mx25l12805d (16384 Kbytes)
 +[    0.592000] bcm63xxpart: CFE boot tag found with version 6 and board type 963281T_TEF
 +[    0.600000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000
 +[    0.608000] bcm63xxpart: Partition 1 is kernel offset 10100 and length eff00
 +[    0.616000] bcm63xxpart: Partition 2 is rootfs offset 100000 and length ef0000
 +[    0.620000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000
 +[    0.628000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000
 +[    0.636000] bcm63xxpart: Spare partition is offset 2e0004 and length d0fffc
 +[    0.644000] 5 bcm63xxpart partitions found on MTD device spi0.0
 +[    0.648000] Creating 5 MTD partitions on "spi0.0":
 +[    0.656000] 0x000000000000-0x000000010000 : "CFE"
 +[    0.664000] 0x000000010100-0x000000100000 : "kernel"
 +[    0.668000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    0.684000] 0x000000100000-0x000000ff0000 : "rootfs"
 +[    0.692000] mtd: partition "rootfs" set to be root filesystem
 +[    0.696000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=D10000 
 +[    0.704000] 0x0000002e0000-0x000000ff0000 : "rootfs_data"
 +[    0.712000] 0x000000ff0000-0x000001000000 : "nvram"
 +[    0.720000] 0x000000010000-0x000000ff0000 : "linux"
 +[    0.764000] bcm63xx-wdt bcm63xx-wdt:  started, timer margin: 30 sec
 +[    0.772000] Registered led device: 963281T_TEF:green:power
 +[    0.772000] Registered led device: 963281T_TEF:red:stop
 +[    0.772000] Registered led device: 963281T_TEF:green:inet
 +[    0.772000] Registered led device: 963281T_TEF:red:inet-fail
 +[    0.776000] Registered led device: 963281T_TEF:green:ppp
 +[    0.776000] Registered led device: 963281T_TEF:red:ppp-fail
 +[    0.776000] Registered led device: 963281T_TEF:green:3g
 +[    0.776000] Registered led device: 963281T_TEF:red:3g-fail
 +[    0.776000] Registered led device: 963281T_TEF:green:wlan
 +[    0.776000] Registered led device: 963281T_TEF:red:wlan-fail
 +[    0.776000] Registered led device: 963281T_TEF:green:eth
 +[    0.780000] Registered led device: 963281T_TEF:red:eth-fail
 +[    0.780000] TCP westwood registered
 +[    0.784000] NET: Registered protocol family 17
 +[    0.788000] 8021q: 802.1Q VLAN Support v1.8
 +[    0.800000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
 +[    0.808000] Freeing unused kernel memory: 200k freed
 +[    3.396000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex
 +[    3.452000] roboswitch: Probing device eth0: 
 +[    3.456000] bcm63xx_enet: could not find a used port with phy_id 0, assuming phy is external
 +[    3.464000] No Robo switch in managed mode found, phy_id = 0xffffffff
 +[    3.472000] roboswitch: Probing device eth1: No such device
 +[    3.476000] roboswitch: Probing device eth2: No such device
 +[    3.480000] roboswitch: Probing device eth3: No such device
 +[    9.436000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000
 +[    9.444000] jffs2_build_filesystem(): unlocking the mtd device... done.
 +[    9.448000] jffs2_build_filesystem(): erasing all blocks after the end marker... done.
 +[  101.636000] JFFS2 notice: (335) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found.
 +[  104.920000] Compat-wireless backport release: compat-wireless-2012-06-14
 +[  104.924000] Backport based on wireless-testing.git master-2012-06-14
 +[  104.932000] compat.git: wireless-testing.git
 +[  104.992000] cfg80211: Calling CRDA to update world regulatory domain
 +[  104.996000] cfg80211: World regulatory domain updated:
 +[  105.004000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
 +[  105.012000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[  105.020000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[  105.028000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[  105.036000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[  105.044000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[  105.432000] NET: Registered protocol family 10
 +[  105.496000] There is already a switch registered on the device 'eth0'
 +[  105.504000] roboswitch: Probing device eth1: No such device
 +[  105.508000] roboswitch: Probing device eth2: No such device
 +[  105.516000] roboswitch: Probing device eth3: No such device
 +[  106.152000] b43-phy0: Broadcom 43225 WLAN found (core revision 23)
 +[  106.156000] Broadcom 43xx driver loaded [ Features: PNL ]
 +[  106.192000] Button Hotplug driver version 0.4.1
 +[  106.512000] PPP generic driver version 2.4.2
 +[  106.884000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[  107.088000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
 +[  107.236000] NET: Registered protocol family 24
 +[  107.272000] nf_conntrack version 0.5.0 (462 buckets, 1848 max)
 +[  107.644000] ip6_tables: (C) 2000-2006 Netfilter Core Team
 +[  107.932000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
 +[  112.084000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex
 +[  112.092000] device eth0 entered promiscuous mode
 +[  112.100000] br-lan: port 1(eth0) entered forwarding state
 +[  112.104000] br-lan: port 1(eth0) entered forwarding state
 +[  114.108000] br-lan: port 1(eth0) entered forwarding state
 +[  122.920000] eth0: no IPv6 routers present</nowiki>
 +</WRAP>\\
 +
 +===== Tags =====
 +[[meta:tags|How to add tags]]
 +{{tag>bcm63xx bcm6328 16flash 32ram adsl2+}}
  • Last modified: 2024/02/12 08:58
  • by 127.0.0.1