ADB P.DG A4001N1

CFE version 1.0.37-106.24 for A4001N TEF 0002 BCM96328 (32bit,SP,BE) Build Date: Wed Jan 26 12:59:25 CET 2011 (zu1costast@thorold) Copyright (C) 2000-2009 Broadcom Corporation. HS Serial flash device: name MX25L128, id 0xc218 size 16384KB Total Flash size: 16384K with 4096 sectors Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz Main Thread: TP0 Memory Test Passed Total Memory: 33554432 bytes (32MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.10 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : run.bin Default host flash file name : 2.bin Boot delay (0-9 seconds) : 9 Board Id (0-4) : 963281T_TEF Number of MAC Addresses (1-32) : 11 Base MAC Address : 11:22:33:44:55:66 PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 1 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 Voice Board Configuration (0-11) : *** Press any key to stop auto run (9 seconds) *** Auto run second count down: 9 web info: Waiting for connection on socket 0. web info: Waiting for connection on socket 1. web info: Waiting for connection on socket 2. web info: Waiting for connection on socket 0. web info: Waiting for connection on socket 1. web info: Upload 6818609 bytes, Broadcom image format. web info: Waiting for connection on socket 0. Flashing root file system and kernel at 0xb8800000: ..................................................... . *** Image flash done *** ! Resetting board...HELO CPUI L1CI DRAM ---- PHYS ZQDN PHYE DINT LSYN USYN MSYN LMBE PASS ---- ZBSS CODE DATA L12F MAIN CFE version 1.0.37-106.24 for A4001N TEF 0002 BCM96328 (32bit,SP,BE) Build Date: Wed Jan 26 12:59:25 CET 2011 (zu1costast@thorold) Copyright (C) 2000-2009 Broadcom Corporation. HS Serial flash device: name MX25L128, id 0xc218 size 16384KB Total Flash size: 16384K with 4096 sectors Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz Main Thread: TP0 Memory Test Passed Total Memory: 33554432 bytes (32MB) Boot Address: 0xb8000000 Board IP address : 192.168.1.1:ffffff00 Host IP address : 192.168.1.10 Gateway IP address : Run from flash/host (f/h) : f Default host run file name : run.bin Default host flash file name : 2.bin Boot delay (0-9 seconds) : 9 Boot image (0=latest, 1=previous) : 0 Board Id (0-4) : 963281T_TEF Number of MAC Addresses (1-32) : 11 Base MAC Address : 11:22:33:44:55:66 PSI Size (1-64) KBytes : 24 Enable Backup PSI [0|1] : 1 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 Voice Board Configuration (0-11) : *** Press any key to stop auto run (9 seconds) *** Auto run second count down: 0 Booting from latest image (0xb8800000) ... Code Address: 0x80010000, Entry Address: 0x80014230 Decompression OK! Entry at 0x80014230 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80014230 Linux version 2.6.30 (zu1costast@thorold) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Thu Apr 21 20:1 HS Serial flash device: name MX25L128, id 0xc218 size 16384KB 963281T_TEF prom init CPU revision is: 0002a075 (Broadcom4350) Determined physical RAM map: memory: 01f00000 @ 00000000 (usable) Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00001f00 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00001f00 On node 0 totalpages: 7936 free_area_init_node: node 0, pgdat 802f3830, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 30 pages used for memmap Normal zone: 3810 pages, LIFO batch:0 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 7874 Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200 wait instruction: enabled Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes RCU-based detection of stalled CPUs is enabled. NR_IRQS:128 PID hash table entries: 128 (order: 7, 512 bytes) console [ttyS0] enabled Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) Memory: 28088k/31744k available (2409k kernel code, 3656k reserved, 555k data, 120k init, 0k highmem) Calibrating delay loop... 319.48 BogoMIPS (lpj=159744) Mount-cache hash table entries: 512 net_namespace: 536 bytes NET: Registered protocol family 16 Total Flash size: 16384K with 4096 sectors registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] pci 0000:01:00.0: PME# supported from D0 D3hot pci 0000:01:00.0: PME# disabled pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff] pci 0000:02:00.0: supports D1 D2 pci 0000:01:00.0: PCI bridge, secondary bus 0000:02 pci 0000:01:00.0: IO window: disabled pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff pci 0000:01:00.0: PREFETCH window: disabled PCI: Enabling device 0000:01:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v2.1 Initialized NET: Registered protocol family 8 NET: Registered protocol family 20 NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 1024 (order: 1, 8192 bytes) TCP bind hash table entries: 1024 (order: 0, 4096 bytes) TCP: Hash tables configured (established 1024 bind 1024) TCP reno registered NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher squashfs: version 4.0 with LZMA457 ported by BRCM fuse init (API version 7.11) msgmni has been set to 54 io scheduler noop registered (default) pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check vendor BIOS PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods PPP generic driver version 2.4.2 PPP Deflate Compression module registered PPP BSD Compression module registered NET: Registered protocol family 24 bcm963xx_mtd driver v1.0 File system address: 0xb8800100 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: EHCI Host Controller ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500 ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: OHCI Host Controller ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver usblp Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. brcmboard: brcm_board_init entry SES: Button Interrupt 0x1 is enabled SES: LED GPIO 0x8009 is enabled initLed: led[0]: Gpio=0xffff8003, FailGpio=0xffff8005 initLed: led[1]: Gpio=0xffffffff, FailGpio=0xffffffff initLed: led[2]: Gpio=0xffffffff, FailGpio=0xffffffff initLed: led[3]: Gpio=0xffff800b, FailGpio=0xffff8002 initLed: led[4]: Gpio=0xffff8009, FailGpio=0xffff800a initLed: led[5]: Gpio=0xffffffff, FailGpio=0xffffffff initLed: led[6]: Gpio=0xffffffff, FailGpio=0xffffffff initLed: led[7]: Gpio=0xffff8006, FailGpio=0xffff8007 initLed: led[8]: Gpio=0xffffffff, FailGpio=0xffffffff initLed: led[9]: Gpio=0xffffffff, FailGpio=0xffffffff initLed: led[10]: Gpio=0xffffffff, FailGpio=0xffffffff initLed: led[11]: Gpio=0xffffffff, FailGpio=0xffffffff initLed: led[12]: Gpio=0xffffffff, FailGpio=0xffffffff initLed: led[13]: Gpio=0xffff8004, FailGpio=0xffff8008 initLed: led[14]: Gpio=0xffff8006, FailGpio=0xffff8007 initLed: led[15]: Gpio=0xffff801f, FailGpio=0xffff8014 Serial: BCM63XX driver $Revision: 3.00 $ ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX ttyS1 at MMIO 0xb0000120 (irq = 47) is a BCM63XX bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Apr 21 2011 20:07:12 Broadcom Logger v0.1 Apr 21 2011 20:04:59 Mirror/redirect action on u32 classifier input device check on Actions configured TCP cubic registered NET: Registered protocol family 17 Initializing MCPD Module Ebtables v2.0 registered ebt_time registered ebt_ftos registered ebt_wmm_mark registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:0. Freeing unused kernel memory: 120k freed init started: BusyBox v1.00 (2011.04.21-18:13+0000) multi-call binary BusyBox v1.00 (2011.04.21-18:13+0000) Built-in shell (ash) Enter 'help' for a list of built-in commands. Loading drivers and kernel modules... bcmxtmcfg: module license 'Proprietary' taints kernel. Disabling lock debugging due to kernel taint bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM6328B0 Ethernet Network Device v0.1 Apr 21 2011 20:05:03 ETH Init: 180 tx BDs at 0xa194e000 ETH Init: 400 rx BDs at 0xa19f8000 ETH Init: 400 rx BDs at 0xa19f9000 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered eth0: MAC Address: 11:22:33:44:55:66 eth1: MAC Address: 11:22:33:44:55:66 eth2: MAC Address: 11:22:33:44:55:66 eth3: MAC Address: 11:22:33:44:55:66 eth0 Link UP 100 mbps full duplex message received before monitor task is initialized kerSysSendtoMonitorTask BCM63XX_USB USB Device not present insmod: cannot insert `/lib/modules/2.6.30/extra/bcm_usb.ko': Success (19): Success PCI: Enabling device 0000:02:00.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:02:00.0 to 64 wl:srom not detected,using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm43225_map.bin wl0: Broadcom BCMa8d8 802.11 Wireless Controller 5.60.120.1.cpePDG_TEF_SP_4.06L4.2 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered Auto-negotiation enabled. The autonegotiated media type is 100baseTx-FD. Link is up mii register 26 is 0x4000 ===== Release Version PDG_TEF_SP_4.06L.4 (build timestamp 110421_2011) ===== factoryCfg = 0 iptables v1.4.0: can't initialize iptables table `nat': iptables who? (do you need to insmod?) Perhaps iptables or your kernel needs to be upgraded. sendto: Network is unreachable ip_tables: (C) 2000-2006 Netfilter Core Team device eth0 entered promiscuous mode br0: port 1(eth0) entering forwarding state device eth1 entered promiscuous mode device eth2 entered promiscuous mode device eth3 entered promiscuous mode device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state ssk:error:23.000:BcmAdsl_Initialize=0xC00A50D8, g_pFnNotifyCallback=0xC00D5E04 rutDsl_CfgProfileInit:2015:rutDsl_CfgProfileInit() WLmngr Daemon is running optarg=0 shmId=0 wlevt_init@107: opened loopback socket 4 wlevt is ready for new msg... pSdramPHY=0xA1FFFFF8, 0x840002 0x40099 AdslCoreSharedMemInit: shareMemAvailable=484928 AdslCoreHwReset: AdslOemDataAddr = 0xA1F6AEB4 dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered XTM Init: 400 rx BDs at 0xa0bb5000 XTM Init: 100 rx BDs at 0xa0b12000 Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (496 buckets, 1984 max) iptables: No chain/target/match by that name monitor task is initialized pid= 244 There is no Predefined DevicePin in CFE WPS Device PIN = 29942275 backup_psi_number_blk=6 result=24576 device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state backup_psi_number_blk=6 result=24576 Setting SSID: "ESRO2" Setting SSID: "wlwl0.1 (): not using net_device_ops yet 0_Guest1" Setting SSID: "wlwl0.2 (): not using net_device_ops yet 0_Guest2" Setting SSID: "wlwl0.3 (): not using net_device_ops yet 0_Guest3" br0: port 5(wl0) entering disabled state wlctl: Unsupported wlctl: Unsupported wlctl: Unsupported wlctl: Undefined error chanspec 0x2b01 selected device wl0 left promiscuous mode br0: port 5(wl0) entering disabled state device wl0 entered promiscuous mode br0: port 5(wl0) entering forwarding state Reaped 1381 UPnP daemon is ready to run

[ 0.000000] Linux version 3.3.8 (noltari@skynet) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #4 Mon Jun 25 11:34:01 CEST 2012 [ 0.000000] Detected Broadcom 0x6328 CPU revision 10b0 [ 0.000000] CPU frequency is 320 MHz [ 0.000000] 32MB of RAM installed [ 0.000000] registering 32 GPIOs [ 0.000000] gpiochip_add: registered GPIOs 0 to 31 on device: bcm63xx-gpio [ 0.000000] board_bcm963xx: Boot address 0xb8000000 [ 0.000000] board_bcm963xx: CFE version: A4001N-V0003 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350) [ 0.000000] board_bcm963xx: board name: 963281T_TEF [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 02000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone PFN ranges: [ 0.000000] Normal 0x00000000 -> 0x00002000 [ 0.000000] Movable zone start PFN for each node [ 0.000000] Early memory PFN ranges [ 0.000000] 0: 0x00000000 -> 0x00002000 [ 0.000000] On node 0 totalpages: 8192 [ 0.000000] free_area_init_node: node 0, pgdat 802a39f0, node_mem_map 81000000 [ 0.000000] Normal zone: 64 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 8128 pages, LIFO batch:0 [ 0.000000] Reserving 0MB of memory at 0MB for crashkernel [ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768 [ 0.000000] pcpu-alloc: 0 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128 [ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200 [ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes) [ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes. [ 0.000000] Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes [ 0.000000] Memory: 29384k/32768k available (2240k kernel code, 3384k reserved, 400k data, 200k init, 0k highmem) [ 0.000000] NR_IRQS:128 [ 0.000000] Calibrating delay loop... 318.46 BogoMIPS (lpj=636928) [ 0.036000] pid_max: default: 32768 minimum: 301 [ 0.040000] Mount-cache hash table entries: 512 [ 0.048000] NET: Registered protocol family 16 [ 0.280000] registering PCI controller with io_map_base unset [ 0.288000] bio: create slab <bio-0> at 0 [ 0.292000] PCI host bridge to bus 0000:00 [ 0.296000] pci_bus 0000:00: root bus resource [mem 0x10f00000-0x11efffff] [ 0.300000] pci_bus 0000:00: root bus resource [ 0x00000000 flags 0x0] [ 0.304000] pci 0000:00:00.0: [14e4:6328] type 1 class 0x000604 [ 0.304000] pci 0000:00:00.0: PME# supported from D0 D3hot [ 0.304000] pci 0000:01:00.0: [14e4:a8d8] type 0 class 0x000280 [ 0.304000] pci 0000:01:00.0: reg 10: [mem 0x00000000-0x00003fff 64bit] [ 0.304000] pci 0000:01:00.0: supports D1 D2 [ 0.304000] pci 0000:00:00.0: BAR 8: assigned [mem 0x10f00000-0x10ffffff] [ 0.308000] pci 0000:01:00.0: BAR 0: assigned [mem 0x10f00000-0x10f03fff 64bit] [ 0.312000] pci 0000:00:00.0: PCI bridge to [bus 01-01] [ 0.316000] pci 0000:00:00.0: bridge window [mem 0x10f00000-0x10ffffff] [ 0.320000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 0.324000] Switching to clocksource MIPS [ 0.332000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002) [ 0.340000] bcma: Found chip with id 0xA8D9, rev 0x01 and package 0x0A [ 0.344000] bcma: Core 0 found: ChipCommon (manuf 0x4BF, id 0x800, rev 0x22, class 0x0) [ 0.352000] bcma: Core 1 found: IEEE 802.11 (manuf 0x4BF, id 0x812, rev 0x17, class 0x0) [ 0.360000] bcma: Core 2 found: PCIe (manuf 0x4BF, id 0x820, rev 0x0F, class 0x0) [ 0.444000] bcma: Failed to get SPROM: -71 [ 0.452000] bcma: Bus registered [ 0.456000] NET: Registered protocol family 2 [ 0.460000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.468000] TCP established hash table entries: 1024 (order: 1, 8192 bytes) [ 0.476000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.480000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.488000] TCP reno registered [ 0.492000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.496000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.504000] NET: Registered protocol family 1 [ 0.508000] PCI: CLS 0 bytes, default 16 [ 0.512000] audit: initializing netlink socket (disabled) [ 0.516000] type=2000 audit(0.516:1): initialized [ 0.524000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.528000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.540000] msgmni has been set to 57 [ 0.544000] io scheduler noop registered [ 0.548000] io scheduler deadline registered (default) [ 0.556000] bcm63xx_uart.0: ttyS0 at MMIO 0xb0000100 (irq = 36) is a bcm63xx_uart [ 0.564000] console [ttyS0] enabled, bootconsole disabled [ 0.580000] m25p80 spi0.0: found mx25l12805d, expected m25p80 [ 0.588000] m25p80 spi0.0: mx25l12805d (16384 Kbytes) [ 0.592000] bcm63xxpart: CFE boot tag found with version 6 and board type 963281T_TEF [ 0.600000] bcm63xxpart: Partition 0 is CFE offset 0 and length 10000 [ 0.608000] bcm63xxpart: Partition 1 is kernel offset 10100 and length eff00 [ 0.616000] bcm63xxpart: Partition 2 is rootfs offset 100000 and length ef0000 [ 0.620000] bcm63xxpart: Partition 3 is nvram offset ff0000 and length 10000 [ 0.628000] bcm63xxpart: Partition 4 is linux offset 10000 and length fe0000 [ 0.636000] bcm63xxpart: Spare partition is offset 2e0004 and length d0fffc [ 0.644000] 5 bcm63xxpart partitions found on MTD device spi0.0 [ 0.648000] Creating 5 MTD partitions on "spi0.0": [ 0.656000] 0x000000000000-0x000000010000 : "CFE" [ 0.664000] 0x000000010100-0x000000100000 : "kernel" [ 0.668000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.684000] 0x000000100000-0x000000ff0000 : "rootfs" [ 0.692000] mtd: partition "rootfs" set to be root filesystem [ 0.696000] mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=D10000 [ 0.704000] 0x0000002e0000-0x000000ff0000 : "rootfs_data" [ 0.712000] 0x000000ff0000-0x000001000000 : "nvram" [ 0.720000] 0x000000010000-0x000000ff0000 : "linux" [ 0.764000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec [ 0.772000] Registered led device: 963281T_TEF:green:power [ 0.772000] Registered led device: 963281T_TEF:red:stop [ 0.772000] Registered led device: 963281T_TEF:green:inet [ 0.772000] Registered led device: 963281T_TEF:red:inet-fail [ 0.776000] Registered led device: 963281T_TEF:green:ppp [ 0.776000] Registered led device: 963281T_TEF:red:ppp-fail [ 0.776000] Registered led device: 963281T_TEF:green:3g [ 0.776000] Registered led device: 963281T_TEF:red:3g-fail [ 0.776000] Registered led device: 963281T_TEF:green:wlan [ 0.776000] Registered led device: 963281T_TEF:red:wlan-fail [ 0.776000] Registered led device: 963281T_TEF:green:eth [ 0.780000] Registered led device: 963281T_TEF:red:eth-fail [ 0.780000] TCP westwood registered [ 0.784000] NET: Registered protocol family 17 [ 0.788000] 8021q: 802.1Q VLAN Support v1.8 [ 0.800000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2. [ 0.808000] Freeing unused kernel memory: 200k freed [ 3.396000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex [ 3.452000] roboswitch: Probing device eth0: [ 3.456000] bcm63xx_enet: could not find a used port with phy_id 0, assuming phy is external [ 3.464000] No Robo switch in managed mode found, phy_id = 0xffffffff [ 3.472000] roboswitch: Probing device eth1: No such device [ 3.476000] roboswitch: Probing device eth2: No such device [ 3.480000] roboswitch: Probing device eth3: No such device [ 9.436000] jffs2_scan_eraseblock(): End of filesystem marker found at 0x10000 [ 9.444000] jffs2_build_filesystem(): unlocking the mtd device... done. [ 9.448000] jffs2_build_filesystem(): erasing all blocks after the end marker... done. [ 101.636000] JFFS2 notice: (335) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 104.920000] Compat-wireless backport release: compat-wireless-2012-06-14 [ 104.924000] Backport based on wireless-testing.git master-2012-06-14 [ 104.932000] compat.git: wireless-testing.git [ 104.992000] cfg80211: Calling CRDA to update world regulatory domain [ 104.996000] cfg80211: World regulatory domain updated: [ 105.004000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) [ 105.012000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 105.020000] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 105.028000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) [ 105.036000] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 105.044000] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) [ 105.432000] NET: Registered protocol family 10 [ 105.496000] There is already a switch registered on the device 'eth0' [ 105.504000] roboswitch: Probing device eth1: No such device [ 105.508000] roboswitch: Probing device eth2: No such device [ 105.516000] roboswitch: Probing device eth3: No such device [ 106.152000] b43-phy0: Broadcom 43225 WLAN found (core revision 23) [ 106.156000] Broadcom 43xx driver loaded [ Features: PNL ] [ 106.192000] Button Hotplug driver version 0.4.1 [ 106.512000] PPP generic driver version 2.4.2 [ 106.884000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 107.088000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 107.236000] NET: Registered protocol family 24 [ 107.272000] nf_conntrack version 0.5.0 (462 buckets, 1848 max) [ 107.644000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 107.932000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0 [ 112.084000] bcm63xx_enetsw bcm63xx_enetsw.0: link UP on Port 4, 100Mbps, full-duplex [ 112.092000] device eth0 entered promiscuous mode [ 112.100000] br-lan: port 1(eth0) entered forwarding state [ 112.104000] br-lan: port 1(eth0) entered forwarding state [ 114.108000] br-lan: port 1(eth0) entered forwarding state [ 122.920000] eth0: no IPv6 routers present