Actiontec C1000A

Common router supplied with CenturyLink (Qwest) ISP subscriptions.

OEM source code available from Actiontec Support - http://opensource.actiontec.com/c1000x.html

SoC Ram Flash Network USB Serial JTag
Broadcom 63168 64 MiB 64 MiB 4 Yes Yes ?

Forum: https://forum.openwrt.org/viewtopic.php?id=51792

Instruction set MIPS
Vendor Broadcom
bootloader cfe
Board ID C1000B
System-On-Chip Broadcom BCM63168
CPU @Frq Dual core BMIPS4350 v8.0 @ 400 MHz
Flash size 64 MiB
Flash Chip NAND512W3A2CN6
RAM size 64 MiB
RAM Chip DDR2
Wireless 802.11b/g/n integrated (SoC)
switch Broadcom BCM53125 / 4x Gigabit ethernet
Modem aDSL2/vDSL2
USB Yes 1 x 2.0
Serial Yes
JTAG Likely

Front:
front

Back:
back

Board:
top bottom

Baud 115200 Data Bits 8 Stop Bits 1 No Parity No Flow Control

CFE version 1.0.38-114.170 for BCM963268 (32bit,SP,BE) Build Date: Tue Nov 25 12:26:31 PST 2014 (yirun@yirun-desktop) Copyright (C) 2000-2011 Broadcom Corporation. NAND flash device: name ST NAND512W3A2CN6, id 0x2076 block 16KB size 65536KB External switch id = 53125 Chip ID: BCM63168C0, MIPS: 400MHz, DDR: 400MHz, Bus: 200MHz Main Thread: TP0 Memory Test Passed Total Memory: 67108864 bytes (64MB) Boot Address: 0xb8000000 Board IP address : 192.168.0.21:ffffff00 Host IP address : 192.168.0.100 Gateway IP address : 192.168.0.1 Run from flash/host (f/h) : f Default host run file name : vmlinux Default host flash file name : bcm963xx_fs_kernel Boot delay (0-9 seconds) : 5 Boot image (0=latest, 1=previous) : 0 Board Id (0-28) : C1000B Number of MAC Addresses (1-32) : 16 Base MAC Address : 20:76:00:59:b0:10 PSI Size (1-64) KBytes : 64 Enable Backup PSI [0|1] : 1 System Log Size (0-256) KBytes : 0 Main Thread Number [0|1] : 0 Board Serial Number : CVPA2212503450 Factory FW Version : CAC001-31.30L.8 WPS PIN : 33771571 WPA KEY : 9cth2kpuds95eu Admin Password : h7Vg7xb7 This is one CFE built for CENTURYLINK C1000A *** Press any key to stop auto run (5 seconds) *** Auto run second count down: 0 Booting from latest image (0xb8004000) ... image check : verified the image blocks 1 to 1306 Decompression OK! Entry at 0x80333eb0 Closing network. Disabling Switch ports. Flushing Receive Buffers... 0 buffers found. Closing DMA Channels. Starting program at 0x80333eb0 Linux version 2.6.30 (yirun@yirun-desktop) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 SMP PREEMPT Tue Nov 25 12:30:32 PST 2014 BCM Flash API. Flash device is not found. C1000B prom init DSL SDRAM reserved: 0x180000 Zone PFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00003e80 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00003e80 On node 0 totalpages: 16000 free_area_init_node: node 0, pgdat 8040c120, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 93 pages used for memmap Normal zone: 11811 pages, LIFO batch:1 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 15875 Kernel command line: root=mtd:rootfs ro rootfstype=jffs2 console=ttyS0,115200 wait instruction: enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes PID hash table entries: 256 (order: 8, 1024 bytes) Allocating memory for DSP module core and initialization code Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0 Calibrating delay loop... Mount-cache hash table entries: 512 Broadcom Logger v0.1 Nov 25 2014 12:27:00 Primary instruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes Total Flash size: 0K with -1 sectors Internal 1P2 VREG will be shutdown if unused...Used, leave it on (00008bb1-0000861b=1430>=300) registering PCI controller with io_map_base unset registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized pci 0000:00:00.0: reg 10 32bit mmio: [0x10004000-0x10005fff] pci 0000:00:00.0: supports D1 D2 pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff] pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff] PCI: Setting latency timer of device 0000:01:00.0 to 64 BLOG v3.0 Initialized BLOG Rule v1.0 Initialized Broadcom IQoS v0.1 Nov 25 2014 12:30:20 initialized Broadcom GBPM v0.1 Nov 25 2014 12:30:21 initialized PCI: Setting latency timer of device 0000:01:00.0 to 64 Driver 'sd' needs updating - please use bus_type methods bcm963xx_mtd driver v2.0 ##init_brcm_physmap exit -->brcmnand_scan: CS=0, numchips=1, csi=0 NAND_CS_NAND_XOR=00000000 Disabling XOR on CS#0 brcmnand_scan: Calling brcmnand_probe for CS=0 B4: NandSelect=40000001, nandConfig=04042300, chipSelect=0 brcmnand_read_id: CS0: dev_id=20762076 After: NandSelect=40000001, nandConfig=04042300 Block size=00004000, erase shift=14 timing1 not adjusted: 6574845b timing2 not adjusted: 00001e96 brcmnand_adjust_acccontrol: gAccControl[CS=0]=00000000, ACC=f7ff1010 brcmnand_scan: Done brcmnand_probe brcmnand_scan: B4 nand_select = 40000001 brcmnand_scan: After nand_select = 40000001 100 CS=0, chip->ctrl->CS[0]=0 ECC level 15, threshold at 1 bits reqEccLevel=0, eccLevel=15 190 eccLevel=15, chip->ecclevel=15, acc=f7ff1010 brcmnand_scan 10 200 CS=0, chip->ctrl->CS[0]=0 200 chip->ecclevel=15, acc=f7ff1010 brcmnand_scan 220 brcmnand_scan 230 brcmnand_scan 40, mtd->oobsize=16, chip->ecclayout=00000000 brcmnand_scan 42, mtd->oobsize=16, chip->ecclevel=15, isMLC=0, chip->cellinfo=0 300 CS=0, chip->ctrl->CS[0]=0 500 chip=83a38190, CS=0, chip->ctrl->CS[0]=0 -->brcmnand_default_bbt brcmnand_default_bbt: bbt_td = bbt_main_descr Bad block table Bbt0 found at page 0001ffe0, version 0x01 for chip on CS0 Bad block table 1tbB found at page 0001ffc0, version 0x01 for chip on CS0 brcmnand_scan 99 Creating 6 MTD partitions on "brcmnand.0": 0x000000008000-0x000001d80000 : "rootfs" 0x000001d84000-0x000003afc000 : "rootfs_update" 0x000003b00000-0x000003f00000 : "data" 0x000000000000-0x000000004000 : "nvram" 0x000000004000-0x000000008000 : "tag" 0x000001d80000-0x000001d84000 : "tag_update" PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM PCI: Enabling device 0000:00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 0000:00:09.0 to 64 brcmboard: brcm_board_init entry SES: Button Interrupt 0x1 is enabled sesBtn_mapIntr: is_sesBtn_irq_shared=0, sesBtn_irq=1 SES: LED GPIO 0x8012 is enabled PCIe: No device found - Powering down brcm_board_init: isShared=0, rstToDflt_irq=0 Total # RxBds=1448 bcmPktDmaBds_init: Broadcom Packet DMA BDs initialized bcmPktDma_init: Broadcom Packet DMA Library initialized bcmxtmrt: Broadcom BCM3168C0 ATM/PTM Network Device v0.5 Nov 25 2014 12:30:07 IPSEC SPU: SUCCEEDED GACT probability NOT on Mirror/redirect action on u32 classifier input device check on Actions configured VFS: Mounted root (jffs2 filesystem) readonly on device 31:0. init started: BusyBox v1.17.2 (2014-11-25 12:33:24 PST) starting pid 227, tty '': '/etc/init.d/rcS' starting pid 232, tty '': '-/bin/sh' BusyBox v1.17.2 (2014-11-25 12:33:24 PST) built-in shell (ash) Enter 'help' for a list of built-in commands. JFFS2 notice: (230) check_node_data: wrong data CRC in data node at 0x002f28cc: read 0xf4c4ab29, calculated 0xc04acbfe. Loading drivers and kernel modules... bcm96368wdt: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint brcmchipinfo: brcm_chipinfo_init entry Broadcom Ingress QoS Module Char Driver v0.1 Nov 25 2014 12:28:34 Registered<243> Broadcom Ingress QoS ver 0.1 initialized BPM: tot_mem_size=67108864B (64MB), buf_mem_size=10066320B (9MB), num of buffers=4730, buf size=2128 Broadcom BPM Module Char Driver v0.1 Nov 25 2014 12:27:24 Registered<244> [NTC bpm] bpm_set_status: BPM status : enabled NBUFF v1.0 Initialized Initialized fcache state Broadcom Packet Flow Cache Char Driver v2.2 Nov 25 2014 12:28:35 Registered<242> Created Proc FS /procfs/fcache Broadcom Packet Flow Cache registered with netdev chain Broadcom Packet Flow Cache learning via BLOG enabled. Constructed Broadcom Packet Flow Cache v2.2 Nov 25 2014 12:28:35 chipId 0x631680C0 Broadcom Forwarding Assist Processor (FAP) Char Driver v0.1 Nov 25 2014 12:28:29 Registered <241> Enabling SMISBUS PHYS_FAP_BASE[0] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done Enabling SMISBUS PHYS_FAP_BASE[1] is 0x10c01000 FAP Soft Reset Done 4ke Reset Done FAP Debug values at 0xa251e3b0 0xa259e3b0 Allocated FAP0 GSO Buffers (0xA252F438) : 1048576 bytes @ 0xA2600000 Allocated FAP1 GSO Buffers (0xA25AF438) : 1048576 bytes @ 0xA2700000 Allocated FAP0 TM SDRAM Queue Storage (a252f43c) : 341376 bytes @ a2000000 Allocated FAP1 TM SDRAM Queue Storage (a25af43c) : 341376 bytes @ a2080000 [NTC fapProto] fapReset : Reset FAP Protocol layer fapDrv_construct: FAP0: pManagedMemory=b0820650. wastage 8 bytes fapDrv_construct: FAP1: pManagedMemory=b0a20650. wastage 8 bytes bcmPktDma_bind: FAP Driver binding successfull [FAP0] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3976>, free <2680>, total<8192> [FAP1] DSPRAM : stack <0x80000000><1536>, global <0x80000600><3976>, free <2680>, total<8192> [FAP0] PSM : addr<0x80002000>, used <23452>, free <1124>, total <24576> [FAP1] PSM : addr<0x80002000>, used <23452>, free <1124>, total <24576> [FAP0] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948 [FAP1] DQM : availableMemory 14652 bytes, nextByteAddress 0xE0004948 [FAP0] GSO Buffer set to 0xA2600000 [FAP1] GSO Buffer set to 0xA2700000 [FAP0] FAP BPM Initialized. [FAP1] FAP BPM Initialized. [FAP0] FAP TM: ON [FAP1] FAP TM: ON bcmxtmcfg: bcmxtmcfg_init entry adsl: adsl_init entry Broadcom BCM63168C0 Ethernet Network Device v0.1 Nov 25 2014 12:30:00 Broadcom GMAC Char Driver v0.1 Nov 25 2014 12:30:05 Registered<249> Broadcom GMAC Driver v0.1 Nov 25 2014 12:30:05 Initialized fapDrv_psmAlloc: fapIdx=1, size: 4800, offset=b0a20650 bytes remaining 7000 ETH Init: Ch:0 - 200 tx BDs at 0xb0a20650 fapDrv_psmAlloc: fapIdx=0, size: 4800, offset=b0820650 bytes remaining 7000 ETH Init: Ch:1 - 200 tx BDs at 0xb0820650 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=0, size: 4808, offset=b0821910 bytes remaining 2184 ETH Init: Ch:0 - 600 rx BDs at 0xb0821910 fapDrv_psmAlloc: wastage 8 bytes fapDrv_psmAlloc: fapIdx=1, size: 4808, offset=b0a21910 bytes remaining 2184 ETH Init: Ch:1 - 600 rx BDs at 0xb0a21910 dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered eth3: MAC Address: 20:76:00:59:B0:10 eth2: MAC Address: 20:76:00:59:B0:10 eth1: MAC Address: 20:76:00:59:B0:10 eth0: MAC Address: 20:76:00:59:B0:10 eth4: MAC Address: 20:76:00:59:B0:10 eth5: MAC Address: 20:76:00:59:B0:10 Broadcom BCM3168C0 USB Network Device v0.4a Nov 25 2014 12:28:41 usb0: MAC Address: 20 76 00 59 B0 13 usb0: Host MAC Address: 20 76 00 59 B0 14 hub 1-0:1.0: over-current change on port 2 USBD Initialization done status 0 USB Link DOWN. [NTC arl] arlEnable : Enabled ARL binding to FAP Broadcom Address Resolution Logic Processor (ARL) Char Driver v0.1 Nov 25 2014 12:27:24 Registered <245> --SMP support wl: dsl_tx_pkt_flush_len=338 wl: high_wmark_tot=3074 PCI: Setting latency timer of device 0000:00:00.0 to 64 wl: passivemode=1 wl: napimode=0 wl0: allocskbmode=1 currallocskbsz=512 Neither SPROM nor OTP has valid image wl:srom/otp not programmed, using main memory mapped srom info(wombo board) wl:loading /etc/wlan/bcm6362_map.bin srom rev:8 wl: reading /etc/wlan/bcmcmn_nvramvars.bin, file size=16 wl0: Broadcom BCM435f 802.11 Wireless Controller 6.30.102.3.cpeCAC002-31.30L76.0 dgasp: kerSysRegisterDyingGaspHandler: wl0 registered Endpoint: endpoint_init entry Endpoint: endpoint_init board id C1000B Endpoint: endpoint_init board id C1000B is not C2000A, exit. insmod: can't insert '/lib/modules/2.6.30/extra/endpointdd.ko': Operation not permitted p8021ag: p8021ag_init entry -/bin/sh: cmf: not found =====CENTURYLINK Release Version CAC002-31.30L.76/CAH005-31.30L.76 (build timestamp 141125_1231) ===== smd:error:17.435:initDls:431:Get Board ID C1000A rm: can't remove '/var/dbus/messagebus.pid': No such file or directory ssk:error:24.597:lck_checkBeforeEntry:230:lock required during cmsObj_getNextInSubTreeFlags ssk:error:24.620:rutVoice_getMaxPhysEndpt:408:failed to open file /dev/bcmendpoint0 ssk:error:24.641:rutVoice_getNumFxoEndpt:521:failed to open file /dev/bcmendpoint0 ssk:error:24.663:rutVoice_getNumFxsEndpt:464:failed to open file /dev/bcmendpoint0 ssk:error:24.685:rutVoice_getNumFxoEndpt:521:failed to open file /dev/bcmendpoint0 ###Tag1 signature(Actiontec),version(CAC002-31.30L.76),version2(CAH005-31.30L.76),imageSequence(538) ###Tag2 signature(Actiontec),version(CAC002-31.30L.76),version2(CAH005-31.30L.76),imageSequence(537) ssk:error:32.540:ctl_rut_reWriteIPv6Hosts:1059:can not open 'hostsv6'-file Host MIPS Clock divider pwrsaving is enabled ssk:error:32.818:insertModuleByIndex:442:Failed on command . ssk:error:32.819:insertModulesWithDep:339:insmod xt_multiport.ko FAILED in insertModuleByIndex() no exist file [/var/autoreservation] error num [2],reason [No such file or directory] Netfilter messages via NETLINK v0.30. ssk:error:35.205:insertModuleByIndex:442:Failed on command . ssk:error:35.206:insertModulesWithDep:339:insmod xt_multiport.ko FAILED in insertModuleByIndex() ssk:error:36.466:insertModuleByIndex:442:Failed on command . ssk:error:36.466:insertModulesWithDep:339:insmod xt_multiport.ko FAILED in insertModuleByIndex() ssk:error:37.730:insertModuleByIndex:442:Failed on command . ssk:error:37.730:insertModulesWithDep:339:insmod xt_multiport.ko FAILED in insertModuleByIndex() ssk:error:38.983:insertModuleByIndex:442:Failed on command . ssk:error:38.984:insertModulesWithDep:339:insmod xt_multiport.ko FAILED in insertModuleByIndex() WLmngr Daemon is running optarg=0 shmId=0 killall: wlevt: no process killed wlevt is ready for new msg... ssk:error:39.936:rcl_lanAlgObject:28:switch SIP ALG to state 0 rmmod nf_conntrack_sip and nf_nat_sip rmmod: can't unload 'nf_nat_sip': unknown symbol in module, or unknown parameter rmmod: can't unload 'nf_conntrack_sip': unknown symbol in module, or unknown parameter BcmAdsl_Initialize=0xC02790F8, g_pFnNotifyCallback=0xC02BDEB4 AdslCoreLoadImage: Single line PHY lmemhdr[2]=0x100CE000, pAdslLMem[2]=0x100CE000 pSdramPHY=0xA3FFFFF8, 0x80008040 0x10280008 *** XfaceOffset: 0x65790 => 0x5FF90 *** *** PhySdramSize got adjusted: 0xEA510 => 0x1217A0 *** AdslCoreSharedMemInit: shareMemSize=67645(67648) AdslCoreHwReset: pLocSbSta=80c88000 bkupThreshold=3072 AdslCoreHwReset: AdslOemDataAddr = 0xA3FA95C4 XdslMediaSearch: current media(0) --> 0x10608700 ***BcmDiagsMgrRegisterClient: 0 *** dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered fapDrv_psmAlloc: fapIdx=1, size: 1600, offset=b0a22be0 bytes remaining 584 XTM Init: Ch:0 - 200 rx BDs at 0xb0a22be0 fapDrv_psmAlloc: fapIdx=1, size: 128, offset=b0a23220 bytes remaining 456 XTM Init: Ch:1 - 16 rx BDs at 0xb0a23220 bcmxtmrt: PTM/ATM Non-Bonding Mode configured in system bcmxtmcfg: gulBondDslMonitorValid = 1 iptables: Bad rule (does a matching rule exist in that chain?) iptables: Bad rule (does a matching rule exist in that chain?) ssk:error:41.371:rutEth_setSwitchWanPort:193:ioctl SIOCSWANPORT ewan0 returns error! ifconfig: ioctl 0x8913 failed: No such device nf_conntrack version 0.5.0 (1024 buckets, 8192 max) iptables: No chain/target/match by that name captiveEnable=0,webActiveLogEnable=0,webSiteBlockEnable=0 set NETLINK_RECV_NO_ENOBUFS ssk:error:42.210:rcl_detectWANServiceObject:321:starting detectWANService, pid=1217 ssk:error:42.224:rcl_wanOpt60Object:371:++++++++newObj->WANOption60=CTL ssk:error:42.322:ssk_init:1388:dbus-daemon is ready now. WPS Device PIN = 33771571 < SES_LED_OFF > Setting SSID: "CenturyLink3450" Setting SSID: "CenturyLink3451" Setting SSID: "CenturyLink3452" Setting SSID: "CenturyLink3453" Setting SSID: "wl0_Guest4" wlctl: Unsupported smd:error:44.378:initDls:431:Get Board ID C1000A ssk:error:44.540:initializeVoice:283:----It's C1000A, Disable voice feature. ifconfig: br1: error fetching interface information: Device not found ifconfig: br2: error fetching interface information: Device not found ifconfig: br3: error fetching interface information: Device not found PMD: Module entry! PMD: couldn't get any msg! PMD: couldn't get any msg! Tue Nov 25 12:31:00 UTC 2014 Broadcom Packet Flow Cache learning via BLOG enabled. Note: Loading 6300 MDK (default) driver for 63168 chip Note: Forcing 53115 driver for 53125 Switch MDK: num_switches = 2 Switch MDK: unit = 0; phy_pbmp = 0x18; config_pbmp = 0x58 status=00 Switch MDK link poll thread: uniteth4 (switch port: 11) Link UP -1 mbps half duplex =0; phypbmp=0x18 AutoNeg is disabled and Speed has changed AutoNeg is disableth5 (switch port: 12) Link UP -1 mbps half duplex ed and Speed has changed ssk:error:46.826:aei_dalVoice_CheckInitCodec:12069:getVpLineObjRet=getVpLineObj()=9804 ssk:error:46.827:setVlCLCodecList:12010:getVpLineObjRet=getVpLineObj()=9804 ssk:error:46.827:setVlCLCodecList:12023:getVpLineCodecListObjRet=cmsObj_getNextInSubTree()=0 ssk:error:46.828:aei_dalVoice_SetVaildCodecs:12123:getVpLineObjRet=getVpLineObj()=9804 Switch MDK link poll thread: unit=1; phypbmp=0xf ssk:error:47.124:ssk_main:1219:cannot handle msg type 0x10000802 acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: scan in progress ... acsd: selected channel spec: 0x1001 eth3 (switch port: 0) Link UP 1000 mbps full duplex < SES_LED_OFF > <WPS_STOP> < SES_LED_OFF > <WPS_SUCCESS> < WSC_EVENTS_PROC_SUCC > >>>>> WPS PushButton Status Change <<<<< iptables: No chain/target/match by that name iptables: Bad rule (does a matching rule exist in that chain?) captiveEnable=0,webActiveLogEnable=0,webSiteBlockEnable=0 iptables: Bad rule (does a matching rule exist in that chain?) iptables: Bad rule (does a matching rule exist in that chain?) iptables: Bad rule (does a matching rule exist in that chain?) ERROR wandev.c:701 get InternetGatewayDevice.LogLevel.2.X_AEI_COM_LogLevel error ERROR wandev.c:719 get InternetGatewayDevice.LogLevel.1.X_AEI_COM_LogLevel error ERROR rtd.c:159 fail to recv msg from msg bus! ERROR rtd.c:159 fail to recv msg from msg bus! ERROR accesscfg.c:314 base64 decode fail! rm: can't remove '/tmp/cfg.xml.gz': No such file or directory WARNING tr69_rut_route.c:98 Both PPPConn and IPConn are Disable! WARNING tr69_rut_route.c:98 Both PPPConn and IPConn are Disable! ERROR tr69_func_aei_firewall_rules.c:69 gwifname is null ERROR tr69_rut_wan6.c:2182 NOT found wan connection! ERROR tr69_rut_wan6.c:2182 NOT found wan connection! ERROR tr69_rut_wan6.c:2182 NOT found wan connection! ERROR tr69_rut_wan6.c:2182 NOT found wan connection! ERROR tr69_rut_wan6.c:2182 NOT found wan connection! ERROR tr69_rut_wan6.c:2182 NOT found wan connection! ===Actiontec xDSL Router=== Login: admin Password: > echo && /bin/sh BusyBox v1.17.2 (2014-11-25 12:33:24 PST) built-in shell (ash) Enter 'help' for a list of built-in commands. #


Insert OpenWrt Bootlog here


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2020/06/10 19:09
  • by danitool