Search

You can find the results of your search below.

OpenSSL benchmarks @docs:guide-user:perf_and_log
1627 Hits, Last modified:
| Raspberry PI 2 Model B ... | Raspberry PI 2 Model B ... | [[toh:raspberry_pi_foundation:raspberry_pi| Raspberry Pi Model B]] | ARM1176JZF-S ... | Raspberry Pi 3 B+
SoC (System on a Chip) @docs:techref:hardware
9 Hits, Last modified:
dware:soc:soc.broadcom.bcm33xx]] === brcm2708 (= Raspberry Pi) === * OpenWrt support is WIP * no, there are... ll ==== === orion === Marvell MV88F**5**18x/MV88F528x * ->[[docs:techref:hardware:soc:soc.marvell]] === kirkwood === Marvell MV88F**6**1xx/MV88F62xx * ->[[docs:techref:hardware:soc:soc.marvell]]... marvell]] ==== Moschip ==== === mcs814x === Only 2 known devices (supported). [[https://oldwiki.arch
SD card @docs:guide-user:installation:installation_methods
6 Hits, Last modified:
d. Common devices that use this procedure include Raspberry Pi and NanoPi. ==== Graphical Utilities ==== Inst... appropriately - e.g. /dev/sda PARTITION="$DEVICE"2 FS_SIZE="$(sudo unsquashfs -s "$PARTITION" | grep... appropriately - e.g. /dev/sda PARTITION="$DEVICE"2 sudo cfdisk "$DEVICE" # select resize, then writ... p://bugs.openwrt.org/index.php?do=details&task_id=2951|link]] or [[docs:guide-user:installation:openw
brcm2708 @docs:techref:targets
5 Hits, Last modified:
====== brcm2708 ====== * Broadcom 2708/2835 (used in the Raspberry Pi) This target was renamed to [[docs:techref:targets:bcm27xx|b... pported using the kernel from ​https://github.com/raspberrypi ===== Other info ===== * [[https://git.le
bcm27xx @docs:techref:targets
5 Hits, Last modified:
to bcm27xx after the 19.07 release. * Broadcom 2708/2835 (used in the Raspberry Pi) ===== Status ===== Fully supported using the kernel patches from ​https://github.com/raspberrypi ===== Other info ===== * [[https://git.le... loads.openwrt.org/snapshots/targets/bcm27xx/bcm2712/openwrt-imagebuilder-bcm27xx-bcm2712.Linux-x86_64.tar.xz|BCM2712 Imagebuilder]] ===== Devices with
CrowdSec @docs:guide-user:services
292 Hits, Last modified:
on on a dedicated device in your network (maybe a Raspberry Pi) and only install the firewall bouncer on the Ope... sec-firewall-bouncer.log</code> <code>time="15-01-2022 08:20:30" level=info msg="config is valid"</code> To check the bouncers status, use the main crowd
Irqbalance @docs:guide-user:services
39 Hits, Last modified:
letion interrupts Err: 0 </code> [[toh:raspberry_pi_foundation:raspberry_pi|Raspberry Pi 4]]: <code> CPU0 CPU1 CPU2 CPU3 3: 7646504 8443043 8250258 670362 GICv2 30 Level arch_timer 11: 172894 0 0 0
DDNS Client DuckDNS @docs:guide-user:services:ddns
3 Hits, Last modified:
listing on Github. * [[http://www.reddit.com/r/raspberry_pi/comments/1mqb9f/duckdns_a_free_ddns_just_got_bett
OpenWrt SystemReady @docs:guide-user
11 Hits, Last modified:
ng HW testing | | ADLINK | ADLINK I-Pi SMARC IMX8M Plus (2 GB LPDDR4) ... | :?: | Missing HW testing | | Raspberry Pi | Raspberry Pi 4 Model B ... | | STMicroelectronics | STMicroelectronics STM32MP157C-EV1 Evaluation board | STM32MP157C | |
Rescue from failed firmware upgrade @docs:guide-user:troubleshooting
18 Hits, Last modified:
ces (e.g. SD-cards) ===== Examples: the different Raspberry PI's, devices of PC Engines). OpenWrt devices that ... i.bin'' on an USB flash drive (must be FAT or FAT32) - Plug USB flash drive into device USB port ... after a few seconds. - The device will take ~15-20 seconds to boot a mini-web server, that provides... der either (if in doubt, try both) - http://192.168.0.1 (TP-Link and newer D-Link devices) -
  • Last modified: 2024/01/03 12:05
  • by aparcar