Search

You can find the results of your search below.

Raspberry Pi @toh:raspberry_pi_foundation
109 Hits, Last modified:
====== Raspberry Pi ====== The Raspberry Pi is a [[wp>single-board computer]] without an [[docs:techref:hardware:switch|Ethernet Network Switch]]. Raspberry Pi 1 and Zero support only soft-float (armel) which is slower than hard-float. Raspberry Pi 2 and 3 are compiled with the ARM hard-float kern
Meraki MR18 installation using JTAG and OpenOCD @toh:meraki:mr18
29 Hits, Last modified:
use of the JTAG, which we're going to do using a Raspberry Pi and open source software. An overview of the proc... he JTAG * Connect both of these interfaces to a Raspberry Pi * Upload an installation kernel into the device... process {{:media:meraki:mr18-reprogramming-using-raspberry-pi.jpg?200|}} ==== Disassembly ==== Remove the rub... meraki:mr18-uart.jpg?200|}} Connect these to the Raspberry Pi's own UART using jumper wire: ^ Raspberry Pi ^ M
Thomson TG784 @toh:thomson
12 Hits, Last modified:
pi ==== For tjtag, flashing the bootloader (using Raspberry Pi 1 B+) takes ~100 seconds. With Pi 2, ~60 seconds. <WRAP center round info 100%> When using Raspberry Pi 2 or 3 and receiving "device not found" errors after running tjtag, use the fork designed for Raspberry Pi 3 and compile with Pi 3 parameter. </WRAP> Note that the tjtag-pi needs word bytes swapped. If this is not already done, th
BT Home Hub 2.0 Type A @toh:bt
10 Hits, Last modified:
m of JTAG hardware** (although this can be just a Raspberry Pi). According to a couple of [[http://openwrt.ebil... t firmware: * [[https://github.com/oxplot/tjtag-pi|tjtag-pi]] via a Raspberry Pi has been used [[https://forum.openwrt.org/viewtopic.php?pid=282665#p282665|three times successfull... * would be better to populate the whole low-pass Pi filter (C136--C138 + C113) to filter power supply
TP-Link Archer MR200 v1 @toh:tp-link
10 Hits, Last modified:
ery is possible by using a CH340a Programmer or a Raspberry Pi, SOIC8 connector/adapter is required, refer to **... rom the board. SOIC8 Adapter is required. **For Raspberry Pi** | Flash Pin | Meaning | Raspberry Pi | | 1 | CS | 24 | | 2 | DO ... ions between the flash chip and the programmer or Raspberry Pi, refer to **Connecting to Flash Chip** for more i
Raspberry Pi Foundation @toh:raspberry_pi_foundation
6 Hits, Last modified:
====== Raspberry Pi Foundation ====== ~~NOCACHE~~ <columns> **Device pages** {{pagequery>* @:toh:raspberry_pi_foundation; cols=1; sort=title; hidestart; hideju... Techdata pages** {{pagequery>Techdata @toh:hwdata:raspberry_pi_foundation; fulltext; cols=1; sort=title; hidesta
TP-Link TL-WPA8630P v2 @toh:tp-link
6 Hits, Last modified:
e"). You can also use a 3.3V UART on an SBC (e.g. Raspberry Pi), but it might be inconsisent when capturing earl... on/Coreboot-ThinkPads/wiki/Hardware-Flashing-with-Raspberry-Pi|Raspberry Pi]]) * ''flashrom'' >= 1.2 Instructions: * Sep
Aruba AP-105 @toh:aruba
4 Hits, Last modified:
ocumentation/hardware/raspberrypi/spi/README.md | Raspberry Pi]]. === Generic Process === If you are not usin... * That your SPI reader is a linux SPI Dev (ex, a Raspberry Pi wired to the SPI Flash) 1. Create a full dump of
Raspberry Pi @toh:hwdata:raspberry_pi_foundation
4 Hits, Last modified:
====== Raspberry Pi ====== ~~NOTRANS~~ **Techdata + Device pages** ---- datatable ---- cols : %title%, Device... header : Techdata page, Device page filter : %class%=techdata filter : Brand=Raspberry Pi sort : %title% ----
Creator Ci40 (Marduk) 02KZ/5+ @toh:creator
4 Hits, Last modified:
faces for external Click boards | ^ Raspberry Pi Interface | Raspberry Pi B+ interface (not simultaneous with Click boards)
TP-Link TL-WR741ND @toh:tp-link
2 Hits, Last modified:
overy_for_TL_MR3020]]. I would recommend you use Raspberry Pi for TFTP server. And you need to connect to seri
Astoria Networks / Arcadyan ARV7519RW22-A-LT (Orange Livebox 2.1) @toh:arcadyan
2 Hits, Last modified:
etup serial console conection (Its posible to use Raspberry Pi and it's UART I/O port) **Attention do it with a
Arcadyan VRV9510KWAC23 (AKA Livebox Next) @toh:arcadyan
2 Hits, Last modified:
etup serial console conection (Its posible to use Raspberry Pi and it's UART I/O port) - Terminal software wit
Meraki MR18 @toh:meraki
2 Hits, Last modified:
(though this not difficult; a method using only a Raspberry Pi is described below) In the event that you have a
MikroTik RB750Gr3 (non-native support, obsoleted with OpenWrt-19.07) @toh:mikrotik
2 Hits, Last modified:
ino]] or a [[https://www.flashrom.org/RaspberryPi|Raspberry Pi]]. == Constructing the image == It's possible
Pine64 PINE A64+ @toh:pine64
2 Hits, Last modified:
Pine64 RockPro64 v2.1 @toh:pine64
2 Hits, Last modified:
Arcadyan AR7516 (aka EE Brightbox 1) @toh:arcadyan
2 Hits, Last modified:
  • Last modified: 2022/09/05 19:03
  • by hauke