Search

You can find the results of your search below.

Belkin F9K1115 v2 (AC 1750 DB)
9 Hits, Last modified:
usb-storage 4-1:1.0 [576380.990000] scsi 0:0:0:0: Direct-Access Corsair Voyager 3.0 1.00 PQ: ... dline registered (default) [ 0.680000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ ... r] to select the debug level [ 7.720000] eth0: link up (1000Mbps/Full duplex) [ 9.400000] jffs2: n... : switching to jffs2 overlay [ 9.450000] eth0: link down [ 9.460000] procd: - early - [ 9.46000
Belkin F9K1109 v1
14 Hits, Last modified:
* * of the firmware for this device. Provide links to firmware images, * * active t... otloader. So you are using u-boot to update flash directly without loading the stock firmware. This ski... e=4096 N_HDLC line discipline registered. Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 2 ports, IRQ s... nnection refused /tmp/twonky_cmd: No such file or directory WaitUntilTwonkyRPCReady: count 19, ret 0 tw
Belkin F7D4401
8 Hits, Last modified:
1 - ?? Pin 2 - TX Pin 3 - RX Pin 4 - GND Directions are relative from the router (I.E plug you... 8) io scheduler noop registered (default) Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ s... rage USB Mass Storage support registered. wl0: wl_link_up: link up wl1: wl_link_up: link up vlan1: dev_set_allmulti(master, 1)</nowiki> </WRAP>\\ ==== OpenWr
Belkin F7D3302 and F7D7302
9 Hits, Last modified:
tart]] if you have no time to write certain stuff link to this | | [[docs:guide-quick-start:checks_and_t... nWrt release]]««««here««««** **DO NOT PROVIDE OWN LINKS to http://downloads.openwrt.org/** ==== Flash L... ines where the other USB port just uses two 0 Ohm links. Don't blame me if you try this and you fry some... 8) io scheduler noop registered (default) Serial: 8250/16550 driver $Revision: 1.1.1.1 $ 4 ports, IRQ s
Belkin F7C027
9 Hits, Last modified:
| | **RAM:** Winbond W9825G6JH - The W9825G6JH is a 256M (32MB) SDRAM | | **Flash:** mx25L12835emi - 128Mbit (16MB) SPI Flash ... io scheduler noop registered (default) reg1_gpio_dir ori = [0x003FABFF] #############################... ####################################### reg1_gpio_dir after 1 = [0x003FABFF] reg1_gpio_dir after 2 = [0
Belkin F7C030
10 Hits, Last modified:
io scheduler noop registered (default) reg1_gpio_dir ori = [0x003FEBFF] #############################... ####################################### reg1_gpio_dir after 1 = [0x003FEBFF] reg1_gpio_dir after 2 = [0x003FEBFF] Ralink gpio driver initialized Gemtek LED ... e to Factory Defaults ################### Serial: 8250/16550 driver $Revision: 1.8 $ 2 ports, IRQ shari
  • Last modified: 2020/12/09 22:33
  • by hauke