Search

You can find the results of your search below.

OpenSSL Benchmarks @docs:guide-user:perf_and_log
674 Hits, Last modified:
| 3300.5 | 248.2 | 281.5 | | r44379 | Broadcom BCM2709 | Raspberry PI 2 Model B | ARMv7 Processor rev 5 (v7l) | 38.40 *... | 1484.6 | 144.7 | 119.0 | | r44379 | Broadcom BCM2709 | Raspberry PI 2 Model B | ARMv7 Processor rev 5 (v7l) | 38.4 | ... .2 | 36.2 | 29.8 | | r36088 Attitude Adjustment (12.09) | Broadcom BCM2708 | [[toh:raspberry_pi_foundation:raspberry_pi| Raspberry Pi Model B]] | ARM1176JZF-S | 697.95 | 1.0.1e | 1... 405380 | 2143570 | 1.7 | 58.2 | 5.8 | 4.7 | | r10121 | Broadcom BCM2710 | Raspberry Pi 3 B+ | 1.4GHz 64-bit 4 core ARM Cortex A53 | 38.4
TP-Link TD-W8970 v1 @toh:tp-link
559 Hits, Last modified:
y.com/6labs/blog/demystifying-hardware-security-%E2%80%93-part-iii/|spi programing post]] when I'm writing flash one of ... 0.810955] bootconsole [early0] disabled [ 0.824383] m25p80 spi0.4: w25q128 (16384 Kbytes) [ 0.827718] 4 ofpart partitions found on MTD device spi0.4 [ 0.833136] Creating 4 MTD partitions on "spi0.4": [ 0... 00000fd0000-0x000001000000 : "boardconfig" [ 1.225352] spi-lantiq 1e100800.spi: Lantiq SPI controller (TXFS 8, RXFS 8, DMA 32) [ 1.334775
Raspberry Pi @toh:raspberry_pi_foundation
447 Hits, Last modified:
ingle-board computers]] without one. OpenWrt for Raspberry Pi 2 is compiled with the ARM hard-float kernel ABI (a... ect&0x135|}} ===== Supported Versions ===== The Raspberry Pi is supported in the **brcm2708** target.\\ Subtargets are **bcm2708** for Raspberry Pi 1, **bcm2709** for the Raspberry Pi 2, **bcm2710** for the Raspberry Pi 3, **bcm2711** for the Raspberry Pi 4.\\ \\ **bcm2709** subtarget can be used for **bcm2710** and **bcm2711** devices.\\ This subta
TP-Link TL-WPA8630P v2 @toh:tp-link
333 Hits, Last modified:
SOIC-8 clip with a flash programmer or SBC (e.g. Raspberry Pi). You will need to ask on the forums for a firmwa... ootm_linux 212 set commandline = console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/sbin/init board=AP152 mtdparts=spi0.0:128k(factory-uboot),128k(u-boot),1024k(uImage)... T) linux_params_init 268 line = console=ttyS0,115200 root=31:03 rootfstype=squashfs init=/sbin/init board=AP152 mtdparts=spi0.0:128k(factory-uboot),128k(u-boot),1024k(uImage)... rg 5: board=AP152 [ 0.000000] arg 6: mtdparts=spi0.0:128k(factory-uboot),128k(u-boot),1024k(uImage),6784k(rootfs),64k(mib0),64k(ART) [ 0
BT Home Hub 2.0 Type A @toh:bt
227 Hits, Last modified:
m of JTAG hardware** (although this can be just a Raspberry Pi). According to a couple of [[http://openwrt.ebil... t firmware: * [[https://github.com/oxplot/tjtag-pi|tjtag-pi]] via a Raspberry Pi has been used [[https://forum.openwrt.org/viewtopic.php?pid=282665#p282665|three times successfully]], at least once [[https://forum.openwrt.org/viewtopic.php?pid=317966#... -0x000000fe0000 : "linux" [ 0.588000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542) [ 0.596000] spi_gpio spi_gpio.1: master is un
SD card @docs:guide-user:installation:installation_methods
7 Hits, Last modified:
[[toh:pcengines:apu#installation1|APU]] * [[toh:raspberry_pi_foundation:raspberry_pi#how_to_flash_openwrt_to_an_sd_card|RPi]] * [[docs:techref:hardware:soc:soc.allwinner.s... this example, the squashfs partiton is ''/dev/sde2''. - You can find the offset, by running ''lose... ) <code>losetup -d -o <offset> /dev/loop0 /dev/sde2</code> - Run filesystem checks <code>fsck.f2fs ... Model!=@@Model@@ filter : installation method(s)=SD card sort : Brand limit : 25 ----
  • Last modified: 2020/12/09 22:33
  • by hauke