Search

Fulltext results:

Extending the router ports with a managed switch with VLANs @docs:guide-user:network:vlan

4 Hits, Last modified: 41 hours ago

ts correctly. Quite a few devices (e.g. the [[toh:netgear:wndr3700|Netgear WNDR3700 v1]]) number their internal ports differently fro

NETGEAR WNDR4300 v1 @toh:netgear

49 Hits, Last modified: 2 days ago

of the router says //WNDR4300//. Similar to [[toh:netgear:WNDR3700]]**v4** but 3T3R. OpenWrt forum [[https://forum.openwrt.org/viewtopic.php?id=41094|thread]] on WNDR3700v4. Stock Netgear WNDR4300v1 comes pre-installed with a modified ve... ing|Install OpenWrt (generic explanation)]] The Netgear WNDR3700(v4) [[toh:netgear:wndr3700#installation|installation instructions]] are appl... tftp'd directly to the router (the chapter [[toh:netgear:wndr3700#recovery_flash_in_failsafe_mode|Recovery flash in

Unlocking the Netgear Telnet Console @toh:netgear

84 Hits, Last modified: 2 days ago

you should be dropped on a '#' prompt. * [[toh:netgear:WNDR3700]] V1.0.7.98: known to work - does not ask for use... ion you will be root at BusyBox v1.4.2. * [[toh:netgear:WNDR3800]] v1.0.0.16 Tested with the python script of telnetenable. * [[toh:netgear:WNDR4000]] v1.0.0.88 works. Does NOT ask for user... you should be dropped on a '#' prompt. * [[toh/netgear/WNDR4300]] V1.0.1.30/34/42 works with the python

Netgear D7800 @toh:netgear

20 Hits, Last modified: 2 days ago

ery mode in the bootloader, similar as some other Netgear routers e.g. WNDR3700. The following steps are from [[toh/netgear/r7800|Netgear R7800]] page which works with D7800. **Prerequisites for TFTP flashing** * A TFTP client... * A new firmware to flash in. Either an original Netgear firmware or an Openwrt "factory.img" firmware. "S

D-Link DIR-825 @toh:d-link

6 Hits, Last modified: 3 days ago

ed the bootloader/calibration data partition from Netgear WNDR3700. It's done through a full reflash, check the foru... or the binary. It turn the D-Link DIR-825 into an Netgear WNDR3700. The Netgear stock firmware does not recognize the 128 MB RAM, it only shows/uses 64 MB RAM, but it start... | | | your local LAN | Switch Netgear ProSafe 5 | 192.168.1.1 | | |

OpenSSL benchmarks @docs:guide-user:perf_and_log

28 Hits, Last modified: 3 days ago

| 45.5 | 37.1 | | r47161 | Atheros AR7161 rev 2 | NETGEAR WNDR3700v1 | MIPS 24Kc V7.4 @800MHz | 531.66 | 1.0.2d | 38... (gcc 4.7.3 linaro; mtune=24kc) | Atheros AR7161 | Netgear WNDR3700v1 | MIPS 24Kc V7.4 | 452.19 | 1.0.1c | 36851370 |... | 27.4 | 22.3 | | r36211 | Atheros AR7161 rev 2 | Netgear WNDR3700v2 | MIPS 24Kc V7.4 | 452.19 | 1.0.1e | 35389740 |... | 28.2 | 23.1 | | r36088 | Atheros AR7161 rev 2 | NETGEAR WNDR3700/WNDR3800/WNDRMAC | MIPS 24Kc V7.4 | 452.19 | 1.0.

Netgear WNDR3800 @toh:netgear

55 Hits, Last modified: 3 weeks ago

angeset/28597|r28597]] | successor to the [[toh:netgear:WNDR3700]] | | v1CHNAS | 201? | - |... ble information can already be found on the [[toh:netgear:wndr3700|WNDR3700 wiki page]]. There is also a WNDR3800-1CHNAS whi... uctions on this page and/or the one for the [[toh:netgear:WNDR3700]]. You can utilize the stock firmware's //Firmwa... FTP method ==== Doing as described in the ->[[toh:netgear:WNDR3700]]. ==== Upgrading OpenWrt ==== You should use