Search

You can find the results of your search below.

Netgear WNDR3700 and WNDR37AV @toh:netgear
153 Hits, Last modified:
====== Netgear WNDR3700 and WNDR37AV ====== {{:media:netgear:wndr3700:wndr3700_v2_general_view.png?300|}} <WRAP 80%> <tabbox Hardware Highlights> ... orm like v1 and v2, NAND flash, same PCB as [[toh:netgear:WNDR4300]], but only 2T2R. May be labeled as WNDR3700-100PES on the packaging's side panel (like some v... topic.php?id=56737|Forum thread]]. | | WNDR37AV | Netgear has sold a number of WNDR3700v2 units in boxes marked WNDR37AV. The hardware is
Netgear R7800 (Nighthawk X4S AC2600) @toh:netgear
140 Hits, Last modified:
ery mode in the bootloader, similar as some other Netgear routers e.g. WNDR3700. **Prerequisites for TFTP flashing** * A TFTP... * A new firmware to flash in. Either an original Netgear firmware or an Openwrt "factory.img" firmware. "S... is no requirement to wait for 10 flashes although Netgear apparently says that in official advice. You can ... arm_cortex-a15_neon-vfpv4 | ^ Vendor | Netgear | ^ Bootloader | U-Boot | ^ System-On-Chip
Unlocking the Netgear Telnet Console @toh:netgear
84 Hits, Last modified:
you should be dropped on a '#' prompt. * [[toh:netgear:WNDR3700]] V1.0.7.98: known to work - does not ask for use... ion you will be root at BusyBox v1.4.2. * [[toh:netgear:WNDR3800]] v1.0.0.16 Tested with the python script of telnetenable. * [[toh:netgear:WNDR4000]] v1.0.0.88 works. Does NOT ask for user... you should be dropped on a '#' prompt. * [[toh/netgear/WNDR4300]] V1.0.1.30/34/42 works with the python
Netgear WNDR3800 @toh:netgear
55 Hits, Last modified:
angeset/28597|r28597]] | successor to the [[toh:netgear:WNDR3700]] | | v1CHNAS | 201? | - |... ble information can already be found on the [[toh:netgear:wndr3700|WNDR3700 wiki page]]. There is also a WNDR3800-1CHNAS whi... uctions on this page and/or the one for the [[toh:netgear:WNDR3700]]. You can utilize the stock firmware's //Firmwa... FTP method ==== Doing as described in the ->[[toh:netgear:WNDR3700]]. ==== Upgrading OpenWrt ==== You should use
NETGEAR WNDR4300 v1 @toh:netgear
49 Hits, Last modified:
of the router says //WNDR4300//. Similar to [[toh:netgear:WNDR3700]]**v4** but 3T3R. OpenWrt forum [[https://forum.openwrt.org/viewtopic.php?id=41094|thread]] on WNDR3700v4. Stock Netgear WNDR4300v1 comes pre-installed with a modified ve... ing|Install OpenWrt (generic explanation)]] The Netgear WNDR3700(v4) [[toh:netgear:wndr3700#installation|installation instructions]] are appl... tftp'd directly to the router (the chapter [[toh:netgear:wndr3700#recovery_flash_in_failsafe_mode|Recovery flash in
Netgear D7800 @toh:netgear
20 Hits, Last modified:
ery mode in the bootloader, similar as some other Netgear routers e.g. WNDR3700. The following steps are from [[toh/netgear/r7800|Netgear R7800]] page which works with D7800. **Prerequisites for TFTP flashing** * A TFTP client... * A new firmware to flash in. Either an original Netgear firmware or an Openwrt "factory.img" firmware. "S
Netgear WNDR4000 @toh:netgear
7 Hits, Last modified:
ter : Model=WNDR4000 ---- Same hardware as [[toh:netgear:WNDR3700|WNDR3700v3]] ===== Installation ===== ---- datatable ---... 8. Download Firmware .zip File from [[https://www.netgear.com/support/product/WNDR4000#download|Netgear]] (tested with WNDR4000-V1.0.0.90_9.1.79.chk) 9. start [[ht... : Broadcom BCM4716 machine : Netgear WNDR4000 processor : 0 cpu model
D-Link DIR-825 @toh:d-link
6 Hits, Last modified:
ed the bootloader/calibration data partition from Netgear WNDR3700. It's done through a full reflash, check the foru... or the binary. It turn the D-Link DIR-825 into an Netgear WNDR3700. The Netgear stock firmware does not recognize the 128 MB RAM, it only shows/uses 64 MB RAM, but it start... | | | your local LAN | Switch Netgear ProSafe 5 | 192.168.1.1 | | |
  • Last modified: 2020/12/09 22:33
  • by hauke