Search

You can find the results of your search below.

GL.iNet GL-MT3000
254 Hits, Last modified:
0_channel_group() 1640: invalid ch_band 0 [ 20.861556] 7981@C14L1,vht80_channel_group() 1571: invalid ch_band 0 ... channel_group() 1571: invalid ch_band 0 [ 26.829615] 7981@C14L1,vht160_channel_group() 1640: invalid ch_band 0 [ 26.836054] 7981@C14L1,vht80_channel_group() 1571: invalid ch_band 0 [ 26.842402] 7981@C14L1,vht160_channel_group() 1640: invalid ch_band 0
GL.iNet GL-MT1300 (Beryl) v1
118 Hits, Last modified:
=0x7615 [ 18.609578] mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 [ 18.614616] AP Driver version-5.0.2.0 [ ... for HIF_MT yet! MACVersion=0x0 [ 18.625286] mt7615_init()--> [ 18.628153] Use the default ePAeLNA ... e! [ 18.632571] Use the default /etc_ro/wlan/MT7615E_EEPROM1.bin bin image! [ 18.639190] <--mt7615_init() [ 18.647843] <-- RTMPAllocTxRxRingMemory, St
GL.iNet GL-AP1300
76 Hits, Last modified:
nnot enable. Maybe the USB cable is bad? [ 73.546159] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 73.551574] usb usb2-port1: cannot disa... 76.646680] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 76.652132] usb usb2-port1: cannot disa... 32) [ 76.766971] IPv6: ADDRCONF(NETDEV_UP): lo: link is not ready [ 76.770388] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 76.778196] IPv6: ADDRCONF(NETDEV
GL.iNet GL-AR750S
68 Hits, Last modified:
nch (git-18.196.56128-9112198) / OpenWrt 18.06.0-rc1 r7090-d2aa3a1b62'' Announced in July, 2018, this... d the reset button, power on, wait until the led blinks 5 times and stays on, then release reset button.... >> Standard size for photos: add ?400 to the medialink */ /* When uploadi... kets). They are lightly adhered and should easily reveal two recessed screw heads. Remove the two scre
GL.iNet GL-MV1000 (Brume) / GL.iNet GL-MV1000W (Brume-W)
57 Hits, Last modified:
s * If you have no time to write certain stuff, link to [[docs:start]] * [[docs:guide-user:base-syst... .g. ''ip addr add dev $yournic 192.168.1.2/24; ip link set $yournic up''. If you’re already in an ''192.... new partition (e.g. ''/dev/mmcblk1p3''). - ''mkdir /mnt/bigroot; mount /dev/mmcblk1p3 /mnt/bigroot''... >> Standard size for photos: add ?400 to the medialink */ /* When uploadi
GL.iNet GL-B2200
56 Hits, Last modified:
* * of the firmware for this device. Provide links to firmware images, * * active t... M Hash algo: crc32 Hash value: 3dd0c135 Hash algo: sha1 Hash value: f7bf... 21 [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d [ 0.000000] CPU: P... : implementor 41 architecture 2 part 30 variant 7 rev 5 [ 0.159568] clocksource: jiffies: mask: 0xff
GL.iNet GL-B1300
51 Hits, Last modified:
>> Standard size for photos: add ?400 to the medialink */ /* When uploadi... wn on the picture with the serial cable connected reverse Rx & Tx because they're labelled from the USB... Image at 84000000 ... Using 'config@ap.dk01.1-c1' configuration Trying 'kernel@1' kernel subima... FIT Image at 84000000 Using 'config@ap.dk01.1-c1' configuration Trying 'fdt@ap.dk01.1-c1' FDT b
GL.iNet GL-MT300A
32 Hits, Last modified:
up ephy on device rt2880-pinmux [ 0.850000] ralink_soc_eth 10100000.ethernet: Error applying setting, reverse things back [ 0.860000] gsw: setting port4 to ephy mode [ 0.870000] ralink_soc_eth 10100000.ethernet eth0 (uninitialized): port 1 link up (100Mbps/Full duplex) [ 0.880000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver [ 0.8
GL.iNet GL-MT300N V1
25 Hits, Last modified:
>> Standard size for photos: add ?400 to the medialink */ /* When uploadi... with Reset Button | | 3.3VD | - | 3.3V | | LINK4 | 44 | Unused | | LINK3 | 43 | Shared with toggle switch on side of device | ==== PoE ==== ... f the plastic part filled, GLI claims this is to prevent confusion over the 3 way toggle, but to keep t
GL.iNet GL-USB150 (aka Microuter)
20 Hits, Last modified:
Reset router to factory defaults if it has been previously configured. * Browse to ''<nowiki>http://... vironment size: 1203/32764 bytes uboot> tftpboot Link down: eth1 Ethernet mode (duplex/speed): 1/100 Mb... bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Atheros AR9330 rev 1 [ 0.000000] Determined physical RAM map: [
  • Last modified: 2024/01/03 12:05
  • by aparcar