Search

You can find the results of your search below.

GL.iNet GL-MT1300 v1
100 Hits, Last modified:
s * If you have no time to write certain stuff, link to [[docs:start]] * [[docs:guide-user:base-syst... 0 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00010000 00010000 "factory" mtd3: 01fb0000 00010... ==== Upgrade via uboot ==== Please refer to the link: https://docs.gl-inet.com/en/3/troubleshooting/de... >> Standard size for photos: add ?400 to the medialink */ /* When uploadi
GL.iNet GL-MV1000 (Brume) / GL.iNet GL-MV1000W (Brume-W)
49 Hits, Last modified:
s * If you have no time to write certain stuff, link to [[docs:start]] * [[docs:guide-user:base-syst... .g. ''ip addr add dev $yournic 192.168.1.2/24; ip link set $yournic up''. If you’re already in an ''192.... 0 "u-boot" mtd1: 00008000 00008000 "u-boot-env" mtd2: 00008000 00008000 "factory" </code> dmesg: <cod... new partition (e.g. ''/dev/mmcblk1p3''). - ''mkdir /mnt/bigroot; mount /dev/mmcblk1p3 /mnt/bigroot''
GL.iNet GL-AP1300
74 Hits, Last modified:
nnot enable. Maybe the USB cable is bad? [ 73.546159] xhci-hcd xhci-hcd.0.auto: Cannot set link state. [ 73.551574] usb usb2-port1: cannot disa... 74.956825] ECM init complete [ 76.031111] rtc-sd2068 0-0032: rtc core: registered sd2068 as rtc0 [ 76.039167] i2c i2c-0: new_device: Instantiated device sd2068 at 0x32 [ 76.646602] usb usb2-port1: Cannot
GL.iNet GL-X300B
28 Hits, Last modified:
0 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00010000 00010000 "art" mtd3: 00fa0000 00010000 ... ==== Upgrade via uboot ==== Please refer to the link: https://docs.gl-inet.com/en/3/troubleshooting/de... >> Standard size for photos: add ?400 to the medialink */ /* When uploadi... ) [ 7.510236] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 8.574549] eth1: link up (1000Mb
GL.iNet GL-E750 (Mudi)
21 Hits, Last modified:
0 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00010000 00010000 "art" mtd3: 00200000 00010000 ... ==== Upgrade via uboot ==== Please refer to the link: https://docs.gl-inet.com/en/3/troubleshooting/de... >> Standard size for photos: add ?400 to the medialink */ /* When uploadi... [[docs:techref:bootloader]] Please refer to the link: https://docs.gl-inet.com/en/3/troubleshooting/de
GL.iNet GL-B1300
60 Hits, Last modified:
initialized [ 32.675371] acfg_attach: 3013: Netlink socket created:ced26400 [ 32.681210] SPECTRAL : get_capability not ... 64 not registered [ 32.729876] spectral_init_netlink 78 NULL SKB [ 32.734200] Green-AP : Green-AP : ... c[1] ..ptr:bfa632b8 [ 32.792215] ath_lowi_if_netlink_init LOWI Netlink successfully created [ 32.798759] osif_wrap_attach:444 osif wrap attached [ 32.80
GL.iNet GL-AR750S
56 Hits, Last modified:
18.196.56128-9112198) / OpenWrt 18.06.0-rc1 r7090-d2aa3a1b62'' Announced in July, 2018, this is an "u... d the reset button, power on, wait until the led blinks 5 times and stays on, then release reset button.... >> Standard size for photos: add ?400 to the medialink */ /* When uploadi... ions including and after ''U-Boot 1.1.4-gcf378d80-dirty (Aug 16 2018 - 07:51:15)'' should work with "an
GL.iNet GL-USB150 (aka Microuter)
19 Hits, Last modified:
** 256 KiB | mtd1 **//u-boot-env//** 64 KiB | mtd2 **//firmware//** 16000 KiB ... 0 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00fa0000 00010000 "firmware" mtd3: 00180000 0001... vironment size: 1203/32764 bytes uboot> tftpboot Link down: eth1 Ethernet mode (duplex/speed): 1/100 Mb... factory reset) button * green: the two LEDs (LED2 and LED1, left to right) * LED1 shows for act
GL.iNet GL-MT300N V1
13 Hits, Last modified:
| **mtd1** \\ ''u-boot-env'' \\ 64 KiB | **mtd2** \\ ''factory'' \\ 64 KiB | **mtd3** \\ ''firm... >> Standard size for photos: add ?400 to the medialink */ /* When uploadi... with Reset Button | | 3.3VD | - | 3.3V | | LINK4 | 44 | Unused | | LINK3 | 43 | Shared with toggle switch on side of device | ==== PoE ====
GL.iNet GL-AR300M-Lite
23 Hits, Last modified:
. It can be used by clicking the "Use WAN as LAN" link on the startpage of the latest original firmware ... 0 "u-boot" mtd1: 00010000 00010000 "u-boot-env" mtd2: 00fa0000 00010000 "firmware" mtd3: 00190000 0001... 'ndp -a'', or the like) can be used to reveal the link-local address. ==== OEM installation using the T... >> Standard size for photos: add ?400 to the medialink */ /* When uploadi
GL.iNet GL-MT300A
18 Hits, Last modified:
* * of the firmware for this device. Provide links to firmware images, * * active t... | **mtd1** \\ ''u-boot-env'' \\ 64 KiB | **mtd2** \\ ''factory'' \\ 64 KiB | **mtd3** \\ ''firm... i>U-Boot 1.1.3 (Dec 23 2015 - 18:37:46) Board: Ralink APSoC DRAM: 128 MB relocate_code Pointer2 at: 87... er deadline registered (default) [ 0.560000] ralink-usb-phy usbphy: invalid resource [ 0.560000] S
  • Last modified: 2022/04/24 10:04
  • by hauke