tion table
sd 0:0:0:0: [sda] Attached SCSI disk
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
ata2.00: ... /block/sdc/device). Returning 3
grep: /var/tmp/devlink: No such file or directory
create_devlink:Using new routine.
linuxrc:c... odules.dep
=== checkroot.sh ===
grep: /var/tmp/devlink: No such file or directory
create_devlink:Using new routine.
swapon: c... ering SWP/SWPB emulation handler
[ 1.558875] ata2: SATA link down (SStatus 0 SControl F300)
[ 6.223833] ran
s
* If you have no time to write certain stuff, link to [[docs:start]]
* [[docs:guide-user:base-syst... *
* of the firmware for this device. Provide links to firmware images, *
* active t... Reset router to factory defaults if it has been previously configured.
* Browse to ''<nowiki>http://... >> Standard size for photos: add ?400 to the medialink */
/* When uploadi
s
* If you have no time to write certain stuff, link to [[docs:start]]
* [[docs:guide-user:base-syst... copy the image file to the device you identified previously, for example:
dd if=/home/username/Downl... >> Standard size for photos: add ?400 to the medialink */
/* When uploadi... MMC1
NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NO
s
* If you have no time to write certain stuff, link to [[docs:start]]
* [[docs:guide-user:base-syst... copy the image file to the device you identified previously, for example:
dd if=/home/username/Downl... >> Standard size for photos: add ?400 to the medialink */
/* When uploadi... MMC1
NOTICE: BL3-1: Running on H5 (1718) in SRAM A2 (@0x44000)
NOTICE: Configuring SPC Controller
NO
*
* of the firmware for this device. Provide links to firmware images, *
* active t... e the reset button after 5 seconds and power LED blinking.
- Upload OpenWrt sysupgrade image via TFTP:... t needs to be pressed until the power LED starts blinking slowly. Window starts at this point |
^ TFTP... )
RT-N56UB1 bootloader version: 1.0.0.0
Board: Ralink APSoC DRAM: 128 MB
ASUS RT-N56UB1 gpio init : wp
.500] eth1 Link UP 100 mbps full duplex
[21474555.505] eth4 Link UP 1000 mbps full duplex
[21474555.545] insmod: a... 0 Is Not Present -- Create It
[21474574.945] eth1 Link DOWN.
<08/09 17:16:02> Create the Default Route e... ........ NAS EAPD WPS started
[21474575.980] eth1 Link UP 100 mbps full duplex
<08/09 17:16:03> check_nt... ddress to master interface
<08/09 17:16:03> eth1: link up, device will be up
<08/09 17:16:03> >>> dhcps_
d, outdoor ethernet router/bridge with integrated directional 5G/NR MIMO antennas. It has a WiFi radio,... ctivities =====
// * OpenWrt forum thread: (add link)
***/
/*** if info available: uncomment and fi... ware =====
//List experimental firmware download links here.//
//None at this time.//
* External image (add link)
* trunk image (add link)
* ...
***/
=====
allow better sensitivity in noisy environment.
**Reverse engineering the control protocol of the filte... mage as shown above
- scp the image to the /tmp directory of your device
- Install OpenWrt using <c... uide-user:installation:generic.sysupgrade]]
==== Revert to stock firmware (untested) ====
You can fla... mware is not touched by OpenWrt, so you will also revert to the config used before OpenWrt.
- scp yo
fwupdate.real binary (which is in fact just a symlink to ubntbox) must be patched:
<code bash>
hexdump ... >> Standard size for photos: add ?400 to the medialink */
/* When uploadi... ze passed from bootloader = 16
[ 0.000000] CPU revision is: 0001974c (MIPS 74Kc)
[ 0.000000] ath_... 64 not registered
[ 13.325000] spectral_init_netlink 54 NULL SKB
[ 13.325000] ol_ath_set_dscp_tid_ma
F(NETDEV_UP): br-lan: link is not ready
[ 27.869505] eth0: link up (1000Mbps/Full duplex)
[ 27.874271] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 27.962503] br-home: port 1(eth0... 8.064836] IPv6: ADDRCONF(NETDEV_CHANGE): br-home: link becomes ready
[ 28.071923] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[ 34.455267] IPv6: ADDRCONF(NETDE
airmax/liteap-ac/|Ubiquiti LiteAP AC]] (LAP-120) previously known as LiteBeam™ ac AP (LBE-5AC-16-120) i... fwupdate.real binary (which is in fact just a symlink to ubntbox) must be patched:
<code bash>
hexdump... de bash>
md5sum /tmp/fwupdate.real
1e51abce9abe5da2b89d91e8980a35f0 /tmp/fwupdate.real
</code>
Afte... fwupdate.real binary (which is in fact just a symlink to ubntbox) must be patched:
<code bash>
hexdump
It consists of two devices:
* the **LAP-120** (previously known as LiteBeam™ AC AP or LBE-5AC-16-120)... Reset router to factory defaults if it has been previously configured.
* Browse to ''<nowiki>http://... fe mode =====
During power on, the blue LED will blink for a few seconds. During this time, press the "R... ct (i.e. a paper clip) a few times until the LED blinks faster. In a few moments the device will enter f
*
* of the firmware for this device. Provide links to firmware images, *
* active t... wd" command to set up a new password
in order to prevent unauthorized SSH logins.
---------------------... >> Standard size for photos: add ?400 to the medialink */
/* When uploadi... ing cores 0x3
Linux version 4.9.79-UBNT (ubnt@8b46a25fc5c7) (gcc version 4.7.0 (Cavium Inc. Version: S