Search

You can find the results of your search below.

Netgear WNR3500 v2
390 Hits, Last modified:
i_tbl_rev2 [wl] c00302a0 wlc_attach [wl] c019a110 gain_idx_aci_tbl_rev3 [wl] c0027c9c qm_shl32 [wl] c0042bf8 wlc_... q_tbl_rev0 [wl] c00b9d10 wlc_scan [wl] c01a1038 ant_swctrl_tbl_rev3_3 [wl] c00b5764 wlc_rateset_mcs_build [wl] c00... [wl] c002fbb8 wlc_wme_acp_set [wl] c01aa15c dot11sslpnphy_5GHz_gaintable_rev0 [wl] c0047a60 wlc_create_chspec [wl] c... t [wl] c0048914 wlc_stf_ss_update [wl] c01a1d78 pilot_tbl_rev3 [wl] c0027590 wpa_cipher [wl] c003f3f8 wlc_s
Netgear R6800
171 Hits, Last modified:
e: (-1) [SYSTEM]/bin/ip -6 route del default RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del default RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del default RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del default RTNETLINK answers: No such file or directory [SYSTEM]/bin/ip -6 route del default RTNETLI
Netgear R7800 (Nighthawk X4S AC2600)
138 Hits, Last modified:
== Info ==== ^ Architecture | ARMv7 Processor rev 0 (v7l), arm_cortex-a15_neon-vfpv4 | ^ Vendor | Netgear | ^ Bo... re" 0x000007900000-0x000007980000 : "crashdump" ata1: SATA link down (SStatus 0 SControl 300) 0x000007980000-0x00... 00-0x2900017f] port 0x100 irq 26 [ 5.497002] ata1: SATA link down (SStatus 0 SControl 300) [ 5.502597] ehci... k [ 7.388161] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready Press the [f] key and hit [enter] to
Netgear R7500
95 Hits, Last modified:
s25fl512s m25p80 spi5.0: pm25lv512 (64 Kbytes) ata1: SATA link down (SStatus 0 SControl 300) UBI: attaching mtd6... 00-0x2900017f] port 0x100 irq 26 [ 4.926138] ata1: SATA link down (SStatus 0 SControl 300) [ 4.932691] ehci... 400000.ethernet eth1: configuring for fixed/sgmii link mode [ 7.605180] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off [ 7.6129
Netgear WN2500RP v1
86 Hits, Last modified:
terface. ===== Return to Factory Firmware ===== Reverting to stock Netgear firmware "V1.0.0.30_1.0.58... interface soft-bricks router into green flashing/blinking tftp recovery state! Set your PC to a static i... ttps://forum.archive.openwrt.org/viewtopic.php?id=50571|OpenWrt forum archive]] ===== LAN/WAN router ... 3236b for chip BCM43236/3 [ 816.533189] usb 1-2: Direct firmware load for brcm/brcmfmac43236b.clm_blob
NETGEAR WN3000RP v1
73 Hits, Last modified:
s * If you have no time to write certain stuff, link to [[docs:start]] * [[docs:guide-user:base-syst... Reset router to factory defaults if it has been previously configured. * Browse to ''<nowiki>http://... >> Standard size for photos: add ?400 to the medialink */ /* When uploadi... system type : Broadcom BCM5357 chip rev 2 processor : 0 cpu model
Netgear WNDR4700 and WNDR4720
70 Hits, Last modified:
rtc/hctosys.c: unable to open rtc device (rtc0) ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F0300) ata1.00: ATA-9: WDC WD20EFRX-68AX9N0, 80.00A80, max UDMA/133 ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 1/32) ata1.00: configured for UDMA/133 blk_queue_max_hw_segm
Netgear D7800
32 Hits, Last modified:
00-0x2900017f] port 0x100 irq 26 [ 4.308941] ata1: SATA link down (SStatus 0 SControl 300) [ 4.312111] ehci... k [ 6.373646] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 7.434162] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off [ 7.434235] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 9.554166] UBIFS (ubi0:1): back
  • Last modified: 2020/12/09 22:33
  • by hauke