| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision |
| ru:toh:tp-link:tl-wr1043nd [2018/02/17 20:21] – ↷ Links adapted because of a move operation | ru:toh:tp-link:tl-wr1043nd [2018/06/11 17:35] – link fixed tmomas |
|---|
| ====== TP-Link TL-WR1043ND ====== | ====== TP-Link TL-WR1043ND ====== |
| Одно из недорогих устройств, с поддержкой Gigabit Ethernet. Производитель указывает: 3 съемные всенаправленные антенны (RP-SMA разъем) и максимальную мощность передатчика в 24dBm (251 mw, v1.x, v2.x). Примечание: максимальная мощность передатчика и перечень доступных для использования каналов может отличатся в некоторых странах! | Одно из недорогих устройств, с поддержкой Gigabit Ethernet. Производитель указывает: 3 съемные всенаправленные антенны (RP-SMA разъем) и максимальную мощность передатчика в 24dBm (251 mw, v1.x, v2.x). Примечание: максимальная мощность передатчика и перечень доступных для использования каналов может отличатся в некоторых странах! |
| | |
| ===== Поддерживаемые версии ===== | ===== Поддерживаемые версии ===== |
| ^ Версия/Модель ^ H/W Ревизия ^ Дата запуска ^ S/N ^ Поддержка версии OpenWrt ^ Спецификация модели ^ | ^ Версия/Модель ^ H/W Ревизия ^ Дата запуска ^ S/N ^ Поддержка версии OpenWrt ^ Спецификация модели ^ |
| |
| ===== Установка ===== | ===== Установка ===== |
| - [[doc:howto:obtain.firmware]] Вы //должны// загрузить стабильную версию прошивки, в имени которой содержатся слова Factory и SquashFS. | - [[:downloads]] Вы //должны// загрузить стабильную версию прошивки, в имени которой содержатся слова Factory и SquashFS. |
| - [[docs:user-guide:generic.flashing]] Затем, загрузить этот файл прошивки на ваш роутер. | - [[docs:guide-user:installation:generic.flashing]] Затем, загрузить этот файл прошивки на ваш роутер. |
| * Самый //быстрый// способ - это скачать готовый [[http://downloads.openwrt.org/snapshots/trunk/ar71xx/openwrt-ar71xx-generic-tl-wr1043nd-v1-squashfs-factory.bin|собранный trunk образ]], имя файла - openwrt-ar71xx-tl-wr1043nd-v1-squashfs-factory.bin. | * Самый //быстрый// способ - это скачать готовый [[http://downloads.openwrt.org/snapshots/trunk/ar71xx/openwrt-ar71xx-generic-tl-wr1043nd-v1-squashfs-factory.bin|собранный trunk образ]], имя файла - openwrt-ar71xx-tl-wr1043nd-v1-squashfs-factory.bin. |
| * Wi-Fi работает сразу после установки прошивки. | * Wi-Fi работает сразу после установки прошивки. |
| * Самый //надежный// способ - скачать готовый [[http://downloads.openwrt.org/backfire/10.03.1/ar71xx/|стабильный образ прошивки]], имя файла - openwrt-ar71xx-tl-wr1043nd-v1-squashfs-factory.bin. | * Самый //надежный// способ - скачать готовый [[http://downloads.openwrt.org/backfire/10.03.1/ar71xx/|стабильный образ прошивки]], имя файла - openwrt-ar71xx-tl-wr1043nd-v1-squashfs-factory.bin. |
| * Внимание! Этот образ прошивки **не имеет** модулей поддержки Wi-Fi. Вы можете легко установить недостающие пакеты на раздел jffs2 позже: ''opkg update'', затем: ''opkg install kmod-ath9k wpad-mini''. **UPDATE: Backfire (10.03.1, r29592) имеет все модули wifi внутри прошивки.** | * Внимание! Этот образ прошивки **не имеет** модулей поддержки Wi-Fi. Вы можете легко установить недостающие пакеты на раздел jffs2 позже: ''opkg update'', затем: ''opkg install kmod-ath9k wpad-mini''. **UPDATE: Backfire (10.03.1, r29592) имеет все модули wifi внутри прошивки.** |
| * Вы всегда можете [[doc:howto:obtain.firmware.generate|собрать]] прошивку сами, на основе Kamikaze или Backfire. Выберите платформу 'Atheros AR71xx/AT7240/AR913x' и используйте 'TP-Link WR1043ND v1' профиль для сборки. | * Вы всегда можете [[docs:guide-user:additional-software:imagebuilder|собрать]] прошивку сами, на основе Kamikaze или Backfire. Выберите платформу 'Atheros AR71xx/AT7240/AR913x' и используйте 'TP-Link WR1043ND v1' профиль для сборки. |
| |
| It appears that in order to use the "Firmware upgrade" option in the original firmware for installing OpenWRT, the WR1043ND must be connected to internet, or at least to a dhcp server on its WAN port - otherwise it won't flash the OpenWRT image, but come up with original firmware again after reboot. UPDATE: not a problem with hardware v1.8 running stock firmware 20110429: leaving connected back to back the Windows client PC performing the upgrade was good enough. | It appears that in order to use the "Firmware upgrade" option in the original firmware for installing OpenWRT, the WR1043ND must be connected to internet, or at least to a dhcp server on its WAN port - otherwise it won't flash the OpenWRT image, but come up with original firmware again after reboot. UPDATE: not a problem with hardware v1.8 running stock firmware 20110429: leaving connected back to back the Windows client PC performing the upgrade was good enough. |
| |
| ==== Flash Layout ==== | ==== Flash Layout ==== |
| Для лучшего понимания, пожалуйста прочтите [[doc:techref:Flash.Layout]]. Там вы найдете много полезной информации. | Для лучшего понимания, пожалуйста прочтите [[docs:techref:flash.layout]]. Там вы найдете много полезной информации. |
| |
| Теперь рассмотрим краткую характеристику разделов флеш-памяти конкретного устройства: | Теперь рассмотрим краткую характеристику разделов флеш-памяти конкретного устройства: |
| ^ Layer2 | | mtd1 **//kernel//** 1280KiB | mtd2 **//rootfs//** 6720KiB || | | ^ Layer2 | | mtd1 **//kernel//** 1280KiB | mtd2 **//rootfs//** 6720KiB || | |
| ^ <color magenta>mountpoint</color> | | | <color magenta>''/''</color> || | | ^ <color magenta>mountpoint</color> | | | <color magenta>''/''</color> || | |
| ^ filesystem | | | [[doc:techref:filesystems#mini_fo|mini_fo]] || | | ^ filesystem | | | [[docs:techref:filesystems#mini_fo|mini_fo]] || | |
| ^ Layer3 | | | | mtd3 **//rootfs_data//** 5184KiB | | | ^ Layer3 | | | | mtd3 **//rootfs_data//** 5184KiB | | |
| ^ Size in KiB | 128KiB | 1280KiB | 1536KiB | 5184KiB | 64KiB | | ^ Size in KiB | 128KiB | 1280KiB | 1536KiB | 5184KiB | 64KiB | |
| ^ Name | **//u-boot//** | **//kernel//** | | **//rootfs_data//** | **//art//** | | ^ Name | **//u-boot//** | **//kernel//** | | **//rootfs_data//** | **//art//** | |
| ^ <color magenta>mountpoint</color> | //none// | //none// | <color magenta>''/rom''</color> | <color magenta>''/overlay''</color> | //none// | | ^ <color magenta>mountpoint</color> | //none// | //none// | <color magenta>''/rom''</color> | <color magenta>''/overlay''</color> | //none// | |
| ^ filesystem | //none// | //none// | [[doc:techref:filesystems#SquashFS]] | [[doc:techref:filesystems#JFFS2]] | //none// | | ^ filesystem | //none// | //none// | [[docs:techref:filesystems#SquashFS]] | [[docs:techref:filesystems#JFFS2]] | //none// | |
| |
| ART = Atheros Radio Test - раздел, который содержит MAC-адреса и данные калибровки wifi (EEPROM). Если раздел отсутствует либо поврежден, - драйвер ath9k не может быть запущен (и соответственно, беспроводная связь работать не будет).\\ | ART = Atheros Radio Test - раздел, который содержит MAC-адреса и данные калибровки wifi (EEPROM). Если раздел отсутствует либо поврежден, - драйвер ath9k не может быть запущен (и соответственно, беспроводная связь работать не будет).\\ |
| |
| ==== Обновление OpenWrt ==== | ==== Обновление OpenWrt ==== |
| -> [[docs:user-guide:generic.sysupgrade]] | -> [[docs:guide-user:installation:generic.sysupgrade]] |
| |
| |
| ==== Назад, к родной прошивке ==== | ==== Назад, к родной прошивке ==== |
| -> [[docs:user-guide:generic.uninstall]] | -> [[docs:guide-user:installation:generic.uninstall]] |
| |
| {{page>meta:infobox:dangerous&noheader&nofooter&noeditbtn}} | {{page>meta:infobox:dangerous&noheader&nofooter&noeditbtn}} |
| |
| This has been confirmed by [[https://forum.openwrt.org/viewtopic.php?pid=110583#p110583|supertom64]] | This has been confirmed by [[https://forum.openwrt.org/viewtopic.php?pid=110583#p110583|supertom64]] |
| |
| |
| |
| ===== Основные настройки ===== | ===== Основные настройки ===== |
| После прошивки, начинайте [[doc:howto:basic.config|Базовую настройку]].\\ | После прошивки, начинайте [[docs:guide-quick-start:checks_and_troubleshooting|Базовую настройку]].\\ |
| Сконфигурируйте ваше Интернет-соединение, настройте беспроводную связь, USB-порты, и т.д. | Сконфигурируйте ваше Интернет-соединение, настройте беспроводную связь, USB-порты, и т.д. |
| | |
| ===== Специальные настройки ===== | ===== Специальные настройки ===== |
| ==== Интерфейс ==== | ==== Интерфейс ==== |
| |
| Некоторые нюансы, касающиеся версии 10.03.1-rc4 на аппаратной версии 1.8 смотрите [[https://forum.openwrt.org/viewtopic.php?pid=123269#p123269|здесь]]. | Некоторые нюансы, касающиеся версии 10.03.1-rc4 на аппаратной версии 1.8 смотрите [[https://forum.openwrt.org/viewtopic.php?pid=123269#p123269|здесь]]. |
| | |
| ==== Безопасный режим ==== | ==== Безопасный режим ==== |
| -> [[doc:howto:generic.failsafe|OpenWrt Failsafe Mode]] | -> [[docs:guide-user:troubleshooting:failsafe_and_factory_reset|OpenWrt Failsafe Mode]] |
| |
| Включите ваш маршрутизатор. После того, как индикатор 'SYS' начнет мигать, нажмите и удерживайте кнопку //QSS// (Находится на передней панели справа), до тех пор, пока индикатор 'SYS' не начнет мигать быстрее. | Включите ваш маршрутизатор. После того, как индикатор 'SYS' начнет мигать, нажмите и удерживайте кнопку //QSS// (Находится на передней панели справа), до тех пор, пока индикатор 'SYS' не начнет мигать быстрее. |
| </code> | </code> |
| в течении 1 секунды. Затем используйте этот метод - [[#OEM installation using the TFTP and RS232 method]] | в течении 1 секунды. Затем используйте этот метод - [[#OEM installation using the TFTP and RS232 method]] |
| |
| |
| |
| | **[[wp>Instruction set|Architecture]]:** | [[wp>MIPS architecture|MIPS]] | | | **[[wp>Instruction set|Architecture]]:** | [[wp>MIPS architecture|MIPS]] | |
| | **Vendor:** | [[wp>Qualcomm Atheros]] | | | **Vendor:** | [[wp>Qualcomm Atheros]] | |
| | **[[doc:techref:Bootloader]]:** | [[doc:techref:bootloader:uboot|U-Boot]] | | | **[[docs:techref:bootloader]]:** | [[docs:techref:bootloader:uboot|U-Boot]] | |
| | **[[doc:hardware:soc|System-On-Chip]]:** | AR9132 rev 2 (MIPS 24Kc V7.4) | | | **[[docs:techref:hardware:soc|System-On-Chip]]:** | AR9132 rev 2 (MIPS 24Kc V7.4) | |
| | **[[doc:hardware:cpu|CPU]]/Speed** | 24Kc V7.4 400 Mhz | | | **[[docs:techref:hardware:cpu|CPU]]/Speed** | 24Kc V7.4 400 Mhz | |
| | **Flash-Chip:** | [[http://www.spansion.com/Support/Datasheets/S25FL064P_00_03_e.pdf|ST 25P64V6P]] | | | **Flash-Chip:** | [[http://www.spansion.com/Support/Datasheets/S25FL064P_00_03_e.pdf|ST 25P64V6P]] | |
| | **Flash size:** | 8192 KiB | | | **Flash size:** | 8192 KiB | |
| | **RAM:** | 32 MiB | | | **RAM:** | 32 MiB | |
| | **Wireless:** | Atheros AR9103 2.4ghz 802.11bgn | | | **Wireless:** | Atheros AR9103 2.4ghz 802.11bgn | |
| | **Ethernet:** | [[http://www.realtek.com.tw/products/productsView.aspx?Langid=1&PNid=18&PFid=15&Level=5&Conn=4&ProdID=197|RealTek RTL8366RB 5-port Gigabit switch w/ vlan support]], [[doc:techref:swconfig]] | | | **Ethernet:** | [[http://www.realtek.com.tw/products/productsView.aspx?Langid=1&PNid=18&PFid=15&Level=5&Conn=4&ProdID=197|RealTek RTL8366RB 5-port Gigabit switch w/ vlan support]], [[docs:techref:swconfig]] | |
| | **Internet:** | н/д | | | **Internet:** | н/д | |
| | **USB:** | Yes 1 x 2.0 | | | **USB:** | Yes 1 x 2.0 | |
| | **[[doc:hardware:port.serial|Serial]]:** | [[#Serial|Yes]] | | | **[[docs:techref:hardware:port.serial|Serial]]:** | [[#Serial|Yes]] | |
| | **[[doc:hardware:port.jtag|JTAG]]:** | [[#JTAG|Yes]] | | | **[[docs:techref:hardware:port.jtag|JTAG]]:** | [[#JTAG|Yes]] | |
| |
| |
| |
| ==== Производительность ==== | ==== Производительность ==== |
| See -> [[doc:hardware:performance]] for results and [[docs:user-guide:advanced:performance]] for help for measuring | See -> [[docs:techref:hardware:performance]] for results and [[docs:guide-user:perf_and_log:performance]] for help for measuring |
| |
| ==== Потребляемая мощность ==== | ==== Потребляемая мощность ==== |
| - Push the front towards the back so the hooks are engaged, then push down the top cover. | - Push the front towards the back so the hooks are engaged, then push down the top cover. |
| - Fasten the screws and re-apply the rubber feet. | - Fasten the screws and re-apply the rubber feet. |
| | |
| ==== Serial ==== | ==== Serial ==== |
| -> [[doc:hardware:port.serial]] general information about the serial port, serial port cable, etc. | -> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc. |
| How to connect to Serial Port: | How to connect to Serial Port: |
| |
| |
| ==== JTAG ==== | ==== JTAG ==== |
| -> [[doc:hardware:port.JTAG]] общая информация про JTAG-порт, JTAG-кабель, и т.д. | -> [[docs:techref:hardware:port.jtag]] общая информация про JTAG-порт, JTAG-кабель, и т.д. |
| |
| {{:media:tplink:tl-wr1043:tl-wr1043nd_jtagport.jpg?direct&600|}} | {{:media:tplink:tl-wr1043:tl-wr1043nd_jtagport.jpg?direct&600|}} |
| |
| ==== GPIOs ==== | ==== GPIOs ==== |
| -> [[doc:hardware:port.GPIO]] | -> [[docs:techref:hardware:port.gpio]] |
| The AR913x platform provides 22 GPIOs. Some of them are used by the router for status LEDs, buttons and to communicate with the RTL8366RB. The table below shows the results of some investigation: | The AR913x platform provides 22 GPIOs. Some of them are used by the router for status LEDs, buttons and to communicate with the RTL8366RB. The table below shows the results of some investigation: |
| |
| |
| ==== Светодиоды ==== | ==== Светодиоды ==== |
| Пример конфигурации светодиодов смотрите в секции LED в [[doc/uci/system]]. | Пример конфигурации светодиодов смотрите в секции LED в [[docs:guide-user:base-system:led_configuration]]. |
| |
| WR1043ND имеет 10 светодиодов: | WR1043ND имеет 10 светодиодов: |
| |
| ==== Кнопки ==== | ==== Кнопки ==== |
| см. [[docs:user-guide:hardware:hardware.button]] | см. [[docs:guide-user:hardware:hardware.button]] |
| |
| У TP-Link TL-WR1043ND V1.х есть две кнопки: | У TP-Link TL-WR1043ND V1.х есть две кнопки: |
| В апп. версии 2.х, обе кнопки расположены сзади, возле портов, нажать на них легко пальцем. | В апп. версии 2.х, обе кнопки расположены сзади, возле портов, нажать на них легко пальцем. |
| ===== Восстановление ===== | ===== Восстановление ===== |
| -> [[docs:user-guide:generic.debrick]] | -> [[docs:guide-user:troubleshooting:generic.debrick]] |
| |
| **Примечание:** Если вы случайно брикнули свой роутер, перезаписав загрузчик попробуйте следующее: | **Примечание:** Если вы случайно брикнули свой роутер, перезаписав загрузчик попробуйте следующее: |
| |
| ===== Bootloader Mods ===== | ===== Bootloader Mods ===== |
| - you could read about [[doc:techref:bootloader]] in general and about [[doc:techref:bootloader:uboot|Das U-Boot]]/[[doc:techref:bootloader:uboot.config|Configuration of U-Boot]] in particular. | - you could read about [[docs:techref:bootloader]] in general and about [[docs:techref:bootloader:uboot|Das U-Boot]]/[[docs:techref:bootloader:uboot.config|Configuration of U-Boot]] in particular. |
| - the uboot version you find on the 1043 is a fork of mainline U-Boot version 1.1.4 from 2005-12-17 [[ftp://ftp.denx.de/pub/u-boot/|see here]]. You can / you cannot FIXME take a current mainline version of uboot and simply cross-compile it for WR1043ND! TP-Link-Version: [[http://www.tp-link.com/support/gpl.asp]]. It contains the file ''u-boot-ap83.tar.bz2'' which is about 6,06 MiB in size, deflate this as well. The deflated source code will occupy about 37MiB of space, start with reading the ''README''. | - the uboot version you find on the 1043 is a fork of mainline U-Boot version 1.1.4 from 2005-12-17 [[ftp://ftp.denx.de/pub/u-boot/|see here]]. You can / you cannot FIXME take a current mainline version of uboot and simply cross-compile it for WR1043ND! TP-Link-Version: [[http://www.tp-link.com/support/gpl.asp]]. It contains the file ''u-boot-ap83.tar.bz2'' which is about 6,06 MiB in size, deflate this as well. The deflated source code will occupy about 37MiB of space, start with reading the ''README''. |
| - also see [[ftp://ftp.denx.de/pub/u-boot/]] and compare the versions. | - also see [[ftp://ftp.denx.de/pub/u-boot/]] and compare the versions. |
| - you may be able to cross compile the code with the OpenWrt [[wp>toolchain]] [[http://buildroot.org/|Buildroot]]. See [[doc:howto:build]] for guidance. But you may need to use other toolchain to crosscompile, like the ELDK (Embedded Linux Development Kit). | - you may be able to cross compile the code with the OpenWrt [[wp>toolchain]] [[http://buildroot.org/|Buildroot]]. See [[docs:guide-developer:build-system:start]] for guidance. But you may need to use other toolchain to crosscompile, like the ELDK (Embedded Linux Development Kit). |
| - :!: **''Problem:''** you cannot test your bootloader, because for some obscure reason, you don't have write access to the flash via [[#JTAG]]. | - :!: **''Problem:''** you cannot test your bootloader, because for some obscure reason, you don't have write access to the flash via [[#JTAG]]. |
| |
| ==== Мод I²C Tiny-USB ==== | ==== Мод I²C Tiny-USB ==== |
| |
| Though not really a modification of the internal hardware, the [[doc:howto:usb.i2c-tiny-usb|I²C Tiny-USB]] adapter allows you to extend your router with an I²C bus over USB. It is not as cheap as the I²C-GPIO mod, but will not risk your warranty. Remember this bus runs at 5V level, when connecting I²C-devices. | Though not really a modification of the internal hardware, the [[docs:guide-user:hardware:usb.i2c-tiny-usb|I²C Tiny-USB]] adapter allows you to extend your router with an I²C bus over USB. It is not as cheap as the I²C-GPIO mod, but will not risk your warranty. Remember this bus runs at 5V level, when connecting I²C-devices. |
| |
| ===== Теги ===== | ===== Теги ===== |
| {{tag>GigabitEthernet 1NIC 1WNIC 5Port USB JTAG 802.11bgn ath9k 3Ant DetachableAntenna 32RAM 8Flash MIPS MIPS32 24Kc JumboFrames}} | {{tag>GigabitEthernet 1NIC 1WNIC 5Port USB JTAG 802.11bgn ath9k 3Ant DetachableAntenna 32RAM 8Flash MIPS MIPS32 24Kc JumboFrames}} |