FIXME Эта страница еще не полностью переведена. Помогите завершить перевод.
(remove this paragraph once the translation is finished)

Beeline SmartBox GIGA

Beeline SmartBox GIGA — беспроводной маршрутизатор на базе платформы MT7621 с портом USB 3.0. Пока его можно приобрести за сравнительно небольшую стоимость (особенно на avito.ru) по сравнению с другими аппаратами с аналогичными характеристиками.

Beeline SmartBox GIGA

It's recommended to make a backup before you start:

* Set up a tftp server (e.g. tftpd64 for windows)

* Connect to a router using SSH shell and run the following commands:

cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10 11; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 192.168.1.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 192.168.1.2

192.168.1.2 - IP of the tftp server

* Check backups in your tftp root folder.

Install OpenWrt (generic explanation)

1. Downgrade stock (Beeline) firmware to v.1.0.02

2. Give factory OpenWrt image a shorter name, e.g. 1001.img. Or just remove all dots (except before file extension) from the file name.

3. Upload and update the firmware via the original web interface.

Remark: You might need make the 3rd step twice if your running firmware is booted from the Slot 1 (Sercomm0 bootflag). The stock firmware reverses the bootflag (Sercomm0 / Sercomm1) on each firmware update.

mtd partition start size OpenWrt specific
0 u-boot 0x0 0x100000
1 dynamic partition map 0x100000 0x100000
2 Factory 0x200000 0x100000
3 Boot Flag 0x300000 0x100000
4 kernel 0x400000 0x600000
5 Kernel 2 0xa00000 0x600000
6 File System 1 0x1000000 0x1800000 ubiconcat0
7 File System 2 0x2800000 0x1800000
8 Configuration/log 0x4000000 0x800000 ubiconcat1
9 application tmp buffer (Ftool) 0x4800000 0xc00000 ubiconcat2
10 container 0x5400000 0x2800000 ubiconcat3
11 bad block reserved ox7c00000 0x380000

See Installation section

generic.flashing.tftp

Not applicable

  • Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
  • Upload image file for sysupgrade to LuCI
  • Wait for reboot

If you don't have a GUI (LuCI) available, you can alternatively upgrade via the command line. There is a command line method for upgrading:

  • sysupgrade

Note: It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.

sysupgrade

  • Login as root via SSH on 192.168.1.1, copy images to /tmp using SCP and then enter the following commands:
cd /tmp
sysupgrade /tmp/sysupgrade.bin

1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:

    printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3

2. Optional: Update with any stock (Beeline) firmware if you want to overwrite OpenWrt in Slot 0 completely.

generic.debrick

1. Compile sercomm-recovery under the Linux:

 git clone https://github.com/danitool/sercomm-recovery.git
 make

2. Connect the router with a cable and run sercomm-recovery:

 sudo ./sercomm-recovery enp0s3 recovery_giga_stock.bin

where enp0s3 - network interface connected the router, ifconfig - list on available network interfaces

3. Wait until the router is flashed and rebooted.

Download ready recovery images for Turbo+ and GIGA.

Contcat all mtd backup into one file:

 cat mtd0 ... mtd10 > full.bin

Add OOB data:

 bbe -b ":512" -e "A 0000000000000000" full.bin -o full-oob.bin

Basic configuration After flashing, proceed with this.
Set up your Internet connection, configure wireless, configure USB port, etc.

The default network configuration is:

Interface Name Description Default configuration
br-lan LAN & WiFi 192.168.1.1/24
lan1, lan2 LAN ports (1 & 2) br-lan
wan WAN port DHCP
Port Switch port
Internet (WAN) wan
LAN 1 lan1
LAN 2 lan2

hardware.button on howto use and configure the hardware button(s). Here, we merely name the buttons, so we can use them in the above Howto.

The Beeline Smartbox GIGA has the following buttons:

BUTTON Event
Reset / WPS reset

Front:
Beeline SmartBox GIGA Case Front

Back:
Beeline SmartBox GIGA Case Rear

Backside label:
Beeline SmartBox GIGA Label

Note: This will void your warranty!

There are crews on the backplate. There are also clips around the edge of the case you will need to prize open, using, for example, a plastic card.

Main PCB:
Beeline SmartBox GIGA PCB

Beeline SmartBox GIGA PCB

Beeline SmartBox GIGA PCB

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Beeline SmartBox GIGA UART connection

Serial connection parameters
for Beeline SmartBox GIGA
57600, 8N1, 3.3V

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Original Breed for Xiaomi R3G can be used, but breedenter utility is required to enter the Breed. Breed web interface shouldn't be used for flashing firmware or EEPROM backup or recovery. Telnet should be used instead.

See Notes → Breed bootloader section for links

Breed settings for Beeline Smartbox GIGA:

Setting Value
autoboot.command boot flash 0x400100

Capacitor mod USB +5V

Problem

Hanging of Fibocom L860-GL USB modem under high upload.

Solution

Solder the C1840 capacitor in the 5V USB power circuit. The place for it is already exists. Keep the polarity of the capacitor! Rating 100-330 uF x 16V.

Beeline SmartBox GIGA capacitor mod

=================================================================== MT7621 stage1 code Mar 12 2015 14:42:52 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0x0, 1/0 = 599/425 01000000 PLL2 FB_DL: 0xc, 1/0 = 630/394 31000000 PLL4 FB_DL: 0x12, 1/0 = 704/320 49000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 0 0 1 1 1 1 000F:| 0 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0010:| 1 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0011:| 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 DRAMC_DQSCTL1[0e0]=14000000 DRAMC_DQSGCTL[124]=80000000 rank 0 coarse = 16 rank 0 fine = 40 B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 opt_dle value:9 DRAMC_DDR2CTL[07c]=C287221D DRAMC_PADCTL4[0e4]=000022B3 DRAMC_DQIDLY1[210]=0B0C0B0C DRAMC_DQIDLY2[214]=060C090D DRAMC_DQIDLY3[218]=0D060A05 DRAMC_DQIDLY4[21c]=0B050C07 DRAMC_R0DELDLY[018]=00002424 ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 11 9 11 11 13 9 12 6 1 7 10 | 5 11 7 9 5 8 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =36 DQS1 = 36 ================================================================== bit DQS0 bit DQS1 0 (1~69)35 8 (1~64)32 1 (2~67)34 9 (1~65)33 2 (1~70)35 10 (2~68)35 3 (1~71)36 11 (2~67)34 4 (1~71)36 12 (2~70)36 5 (2~71)36 13 (0~66)33 6 (1~71)36 14 (2~70)36 7 (1~71)36 15 (1~66)33 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 12 11 12 11 13 9 12 6 5 10 10 | 6 13 7 12 5 11 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqsdly_pass[1]=15, finish count=2 DQ loop=15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,8) DRAMC_DQODLY1[200]=88888888 DRAMC_DQODLY2[204]=88888888 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Aug 13 2019 - 15:27:14) Board: Ralink APSoC DRAM: 256 MB rt2880 uboot v0.00e04 05/25/2006 SERIAL_CLOCK_DIVISOR =16 kaiker,,CONFIG_BAUDRATE =57600 SDRAM SIZE:10000000 Top of RAM usable for U-Boot at: 8fd00000 Reserving 425k for U-Boot at: 8fc94000 Reserving 1028k for malloc() at: 8fb93000 Reserving 44 Bytes for Board Info at: 8fb92fd4 Reserving 36 Bytes for Global Data at: 8fb92fb0 Reserving 128k for boot params() at: 8fb72fb0 Stack Pointer at: 8fb72f98 relocate_code Pointer at: 8fc94000 Config XHCI 40M PLL Now running in RAM - U-Boot at: 8fc94000 monitor_flash_len =116956 Command "mdio": 0xa02062f0 => 0x8fc9a2f0 Command "nand": 0xa020be4c => 0x8fc9fe4c Command "reset": 0xa0215d6c => 0x8fca9d6c Command "go": 0xa020d7f8 => 0x8fca17f8 Command "bootm": 0xa020e054 => 0x8fca2054 Command "loadb": 0xa020ed14 => 0x8fca2d14 Command "tftpboot": 0xa020f344 => 0x8fca3344 Command "nm": 0xa020fb48 => 0x8fca3b48 Command "mm": 0xa020fbac => 0x8fca3bac Command "md": 0xa020fc10 => 0x8fca3c10 Command "mcmp": 0xa020f744 => 0x8fca3744 Command "saveenv": 0xa02102f4 => 0x8fca42f4 Command "setenv": 0xa0210c64 => 0x8fca4c64 Command "printenv": 0xa0210344 => 0x8fca4344 Command "?": 0xa0210f38 => 0x8fca4f38 Command "help": 0xa0210f38 => 0x8fca4f38 Command "version": 0xa0210df8 => 0x8fca4df8 Command "sc_upgrade_flag": 0xa0213d78 => 0x8fca7d78 Command "sc_boot": 0xa0213db0 => 0x8fca7db0 Command "sc_nand": 0xa0213de8 => 0x8fca7de8 Command "sc_eth_test": 0xa0213e24 => 0x8fca7e24 Command "sc_phy": 0xa0213e60 => 0x8fca7e60 Command "sc_time": 0xa0213e9c => 0x8fca7e9c Command "sc_btver": 0xa0213ed4 => 0x8fca7ed4 Command "sc_fl_map": 0xa0213f10 => 0x8fca7f10 Command "sc_endian": 0xa0213f4c => 0x8fca7f4c Command "sc_gpio": 0xa0213f88 => 0x8fca7f88 Command "sc_led": 0xa0213fc4 => 0x8fca7fc4 Command "sc_mem_usage_info": 0xa021390c => 0x8fca790c Command "sc_dl": 0xa0214000 => 0x8fca8000 Allocate 16 byte aligned buffer: 8fcca3f0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02] Device found in MTK table, ID: c2f1, EXT_ID: 809502 Support this Device in MTK table! c2f1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 *** Warning - bad CRC, using default environment icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes #Reset_MT7530 Load Standalone from 40000 SC_DEBUG: Nand Partition Table Magic Found at 100000. e[31m****************************************** Uboot StandAlone Entry ******************************************e[0m GPIO init ********************************************************* Press any key to enter Boot Command Interface ********************************************************* 0 SC_DEBUG: Nand Partition Table Magic Found at 100000. e[31m****************************************** Uboot StandAlone Entry ******************************************e[0m *************************************************** S2 Boot Version 0100, at Aug 13 2019, 15:27:09 *************************************************** SC_DEBUG: Nand Partition Table Magic Found at 100000. Ethernet is closed . Entering Firmware : Everything is OK. ************************************* Boot Flag : Sercomm1 ************************************* Fw header Magic check OK! FW header checksum should: 0x47b7b0fe, crc32 result: 0x47b7b0fe, Fw header CRC check OK! kernel : real offset: 0x00a20100, data length: 0x003dd3f8,checksum :0x67d1e2fd kernel result: 0x67d1e2fd, kernel check sum ok! rootfs: real offset: 0x02820000, data length: 0x0093e000, checksum :0x81bdb3ef rootfs result: 0x81bdb3ef, rootfs check sum ok! Kernel Addr : 0xbca20100 ## Booting image at bca20100 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 4051896 Bytes = 3.9 MB Load Address: 81001000 Entry Point: 816eb7a0 Verifying Checksum ... OK Uncompressing Kernel Image ... OK kernel addr :0xBCA20100 No initrd ## Transferring control to Linux (at address 816eb7a0) ... ## Giving linux memsize in MB, 256 Starting kernel ... LINUX started... THIS IS ASIC SDK 5.0.S.0 Linux version 3.10.14 (sercomm@pavel) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Tue Mar 10 20:27:48 MSK 2020 The CPU feqenuce set to 880 MHz GCMP present CPU0 revision is: 0001992f (MIPS 1004Kc) Software DMA cache coherency Determined physical RAM map: memory: 0fffc000 @ 00000000 (usable) memory: 00004000 @ 0fffc000 (reserved) Zone ranges: DMA [mem 0x00000000-0x00ffffff] Normal [mem 0x01000000-0x0fffbfff] Movable zone start for each node Early memory node ranges node 0: [mem 0x00000000-0x0fffbfff] Detected 3 available secondary CPU(s) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. PERCPU: Embedded 7 pages/cpu @81ca0000 s6720 r8192 d13760 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65020 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Writing ErrCtl register=00030010 Readback ErrCtl register=00030010 Memory: 248880k/262128k available (7126k kernel code, 13248k reserved, 3223k data, 268k init, 0k highmem) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 Hierarchical RCU implementation. NR_IRQS:128 console [ttyS1] enabled Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 launch: starting cpu1 launch: cpu1 gone! CPU1 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 1: done. launch: starting cpu2 launch: cpu2 gone! CPU2 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 2: done. launch: starting cpu3 launch: cpu3 gone! CPU3 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 3: done. Brought up 4 CPUs devtmpfs: initialized NET: Registered protocol family 16 release PCIe RST: RALINK_RSTCTRL = 7000000 PCIE PHY initialize ***** Xtal 40MHz ***** start MT7621 PCIe register access RALINK_RSTCTRL = 7000000 RALINK_CLKCFG1 = 77ffeff8 *************** MT7621 PCIe RC mode ************* PCIE2 no card, disable it(RST&CLK) pcie_link status = 0x3 RALINK_RSTCTRL= 3000000 *** Configure Device number setting of Virtual PCI-PCI bridge *** RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2 PCIE0 enabled PCIE1 enabled interrupt enable status: 300000 Port 1 N_FTS = 1b105000 Port 0 N_FTS = 1b105000 config reg done init_rt2880pci done bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 9: assigned [mem 0x60000000-0x601fffff pref] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] pci 0000:00:00.0: BAR 1: assigned [mem 0x60300000-0x6030ffff] pci 0000:00:01.0: BAR 1: assigned [mem 0x60310000-0x6031ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit pref] pci 0000:01:00.0: BAR 2: assigned [mem 0x60100000-0x60103fff 64bit pref] pci 0000:01:00.0: BAR 4: assigned [mem 0x60104000-0x60104fff 64bit pref] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [mem 0x60000000-0x601fffff pref] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff] pci 0000:00:01.0: PCI bridge to [bus 02] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] PCI: Enabling device 0000:00:00.0 (0004 -> 0006) PCI: Enabling device 0000:00:01.0 (0004 -> 0006) BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60300000 res[1]->end = 6030ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 BAR0 at slot 1 = 0 bus=0x0, slot = 0x1 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60310000 res[1]->end = 6031ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0, irq=0x4 res[0]->start = 60000000 res[0]->end = 600fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 60100000 res[2]->end = 60103fff res[3]->start = 0 res[3]->end = 0 res[4]->start = 60104000 res[4]->end = 60104fff res[5]->start = 0 res[5]->end = 0 bus=0x2, slot = 0x1, irq=0x18 res[0]->start = 60200000 res[0]->end = 602fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource MIPS NET: Registered protocol family 2 TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 4 CPUs re-calibrate udelay(lpj = 1167360) squashfs: version 4.0 (2009/01/31) Phillip Lougher NTFS driver 2.1.30 [Flags: R/W]. fuse init (API version 7.22) msgmni has been set to 486 io scheduler noop registered (default) reg_int_mask=0, INT_MASK= 0 HSDMA_init hsdma_phy_tx_ring0 = 0x00c00000, hsdma_tx_ring0 = 0xa0c00000 hsdma_phy_rx_ring0 = 0x00c04000, hsdma_rx_ring0 = 0xa0c04000 TX_CTX_IDX0 = 0 TX_DTX_IDX0 = 0 RX_CRX_IDX0 = 3ff RX_DRX_IDX0 = 0 set_fe_HSDMA_glo_cfg HSDMA_GLO_CFG = 465 Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A serial8250: ttyS2 at MMIO 0x1e000e00 (irq = 28) is a 16550A brd: module loaded MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error Allocate 16 byte aligned buffer: 81a77dd0 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02, 00809502] Device found in MTK table, ID: c2f1, EXT_ID: 809502 alloctare : (mtd->writesize + mtd->oobsize) * page_per_block is 135168 Support this Device in MTK table! c2f1 NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Macronix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64 [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Scanning device for bad blocks Bad eraseblock 22 at 0x0000002c0000 Signature matched and data read! load_fact_bbt success 1023 00 00 00 00 00 30 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 SC_DEBUG: Go to read Magic at 100000 page: 200 SC_DEBUG: NAND Partition Table Magic was found at 100000. page: 201 SC_DEBUG: part 0,real_offset 00000000, real_length 00100000 page: 201 SC_DEBUG: part 1,real_offset 00100000, real_length 00100000 page: 201 SC_DEBUG: part 2,real_offset 00200000, real_length 00120000 page: 201 SC_DEBUG: part 3,real_offset 00320000, real_length 00100000 page: 201 SC_DEBUG: part 4,real_offset 00420000, real_length 00600000 page: 201 SC_DEBUG: part 5,real_offset 00a20000, real_length 00600000 page: 201 SC_DEBUG: part 6,real_offset 01020000, real_length 01800000 page: 201 SC_DEBUG: part 7,real_offset 02820000, real_length 01800000 page: 201 SC_DEBUG: part 8,real_offset 04020000, real_length 00800000 page: 201 SC_DEBUG: part 9,real_offset 04820000, real_length 00c00000 page: 201 SC_DEBUG: part 10,real_offset 05420000, real_length 02800000 page: 201 SC_DEBUG: part 11,real_offset 07c20000, real_length 00360000 Creating 12 MTD partitions on "MT7621-NAND": 0x000000000000-0x000000100000 : "Boot Loader" 0x000000100000-0x000000200000 : "dynamic partition map" 0x000000200000-0x000000320000 : "Factory" 0x000000320000-0x000000420000 : "Boot Flag" 0x000000420000-0x000000a20000 : "Kernel 1" 0x000000a20000-0x000001020000 : "Kernel 2" 0x000001020000-0x000002820000 : "File System 1" 0x000002820000-0x000004020000 : "File System 2" 0x000004020000-0x000004820000 : "Configuration/log" 0x000004820000-0x000005420000 : "application tmp buffer (Ftool)" 0x000005420000-0x000007c20000 : "container" 0x000007c20000-0x000007f80000 : "bad block reserved" [mtk_nand] probe successfully! PPP generic driver version 2.4.2 PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 register mt_drv === pAd = c0181000, size = 8000960 === <-- RTMPAllocAdapterBlock, Status=0 pAd->PciHif.CSRBaseAddress =0xc0080000, csr_addr=0xc0080000! RTMPInitPCIeDevice():device_id=0x7663 mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a01, pAd->ChipID=0x7663 mt7663_init()--> <--mt7663_init() <-- RTMPAllocTxRxRingMemory, Status=0 get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) get_wdev_by_idx: invalid idx(0) add_oom_notifier() rdm_major = 253 set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288071 Ralink APSoC Ethernet Driver Initilization. v3.1 4096 rx/tx descriptors allocated, mtu = 1500! set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288011 <0> !! create link_status PROC !!!!! PROC INIT OK! usbcore: registered new interface driver usb-storage Ralink APSoC Hardware Watchdog Timer GACT probability on Mirror/redirect action on Failed to load ipt action u32 classifier Performance counters on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (3888 buckets, 15552 max) ctnetlink v0.93: registering with nfnetlink. NF_TPROXY: Transparent proxy support initialized, version 4.1.0 NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. IPVS: Registered protocols () IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: Creating netns size=776 id=0 IPVS: ipvs loaded. gre: GRE over IPv4 demultiplexor driver ip_tables: (C) 2000-2006 Netfilter Core Team Type=Linux arp_tables: (C) 2002 David S. Miller TCP: cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team NET: Registered protocol family 17 Ebtables v2.0 registered l2tp_core: L2TP core driver, V2.0 l2tp_ppp: PPPoL2TP kernel driver, V2.0 8021q: 802.1Q VLAN Support v1.8 Sercomm dual images: bootflag=Sercomm1, choose /dev/mtdblock7 as rootfs VFS: Mounted root (squashfs filesystem) readonly on device 31:7. devtmpfs: mounted Freeing unused kernel memory: 268K (81a1d000 - 81a60000) init started: BusyBox v1.15.3 () starting pid 51, tty '': '/etc/rcS' mount: mounting usbfs on /proc/bus/usb failed: No such file or directory register rlt_drv === pAd = c0e81000, size = 1295256 === <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc0d80000, csr_addr=0xc0d80000! device_id =0x7603 RtmpChipOpsHook(474): Not support for HIF_MT yet! mt7603_init()--> mt_bcn_buf_init(224): Not support for HIF_MT yet! <--mt7603_init() hal_wd: module license 'sercomm' taints kernel. Disabling lock debugging due to kernel taint Init system monitor... Sercomm HWIO Driver: loaded successfully nUBI: attaching mtd8 to ubi8 UBI: scanning is finished UBI: attached mtd8 (name "Configuration/log", size 8 MiB) to ubi8 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 67/49, WL threshold: 4096, image sequence number: 679372223 UBI: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 20 UBI: background thread "ubi_bgt8d" started, PID 93 UBI device number 8, total 64 LEBs (8126464 byteUBIFS: background thread "ubifs_bgt8_0" started, PID 95 s, 7.8 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 8, volume 0, name "0" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 3809280 bytes (3 MiB, 30 LEBs), journal size 3428352 bytes (3 MiB, 27 LEBs) UBIFS: reserved for root: 0 bytes (0 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID D569DB63-F2CC-4411-9F53-3FA4254DC41A, small LPT model Started WatchDog Timer. SERIAL NUMBER: SQ1731F7F722 FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF Raeth v3.1 (Tasklet) phy_free_head is 0xc9c000!!! phy_free_tail_phy is 0xc9dff0!!! txd_pool=a0ca8000 phy_txd_pool=00CA8000 ei_local->skb_free start address is 0x8e9026cc. free_txd: 00ca8010, ei_local->cpu_ptr: 00CA8000 POOL HEAD_PTR | DMA_PTR | CPU_PTR ----------------+---------+-------- 0xa0ca8000 0x00CA8000 0x00CA8000 phy_qrx_ring = 0x00c9e000, qrx_ring = 0xa0c9e000 phy_rx_ring0 = 0x00cb0000, rx_ring[0] = 0xa0cb0000 MT7530 Reset Completed!! change HW-TRAP to 0x117c8f set LAN/WAN WLLLL GMAC1_MAC_ADRH -- : 0x000060ce GMAC1_MAC_ADRL -- : 0x866eb816 GDMA2_MAC_ADRH -- : 0x0000000c GDMA2_MAC_ADRL -- : 0x432880ba eth3: ===> VirtualIF_open MT7621 GE2 link rate to 1G CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 sc_lan_vlan_id = 1 sc_wan_vlan_id = 2 sc_special_vlan_id = 3 sc_host_queue = 3 rc_cmd=/usr/sbin/rc syslogd start Chain 'FORWARD_WIFI' doesn't exist. Chain 'INPUT_WIFI' doesn't exist. rc_cmd=/usr/sbin/rc wan_switch start rc_cmd=/usr/sbin/rc lan_switch start rc_cmd=/usr/sbin/rc dnrd start rc_cmd=/usr/sbin/rc wlan start ============guest<2> is disabled============ ============guest<3> is disabled============ ============guest<4> is disabled============ ============guest<6> is disabled============ ============guest<7> is disabled============ ============guest<8> is disabled============ Chain 'FORWARD_WIFI' doesn't exist. Chain 'INPUT_WIFI' doesn't exist. rc_cmd=/usr/sbin/rc lanip start init rc_cmd=/usr/sbin/rc firewall start ScDrvDev_ioctl: CMD: (20) is not supported rc_cmd=rc radvd restart [Jan 01 00:00:31] radvd: no linklocal address configured for br0 [Jan 01 00:00:31] radvd: can't join ipv6-allrouters on br0 iptables: Bad rule (does a matching rule exist in that chain?). rc_cmd=/usr/sbin/rc networkmap start init rc_cmd=/usr/sbin/rc qtbl start rc_cmd=/usr/sbin/rc qos start rc_cmd=/usr/sbin/rc cpm start init rc_cmd=/usr/sbin/rc wanip stop 1 rc_cmd=/usr/sbin/rc dnrd stop wid 1 rc_cmd=/usr/sbin/rc hw_nat stop 1 rc_cmd=/usr/sbin/rc qtbl stop 1 rc_cmd=/usr/sbin/rc wanip stop 0 rc_cmd=/usr/sbin/rc dnrd stop wid 0 rc_cmd=/usr/sbin/rc hw_nat stop 0 rc_cmd=/usr/sbin/rc dnrd stop wid 1 rc_cmd=/usr/sbin/rc hw_nat stop 1 rc_cmd=/usr/sbin/rc qtbl stop 0 rc_cmd=/usr/sbin/rc dnrd stop wid 0 Tue Mar 10 21:04:28 UTC 2020 rc_cmd=/usr/sbin/rc qtbl stop 1 rc_cmd=/usr/sbin/rc ntp restart 0 rc_cmd=/usr/sbin/rc httpd start rc_cmd=/usr/sbin/rc hw_nat stop 0 rc_cmd=/usr/sbin/rc qtbl stop 0 rc_cmd=/usr/sbin/rc coredump start rc_cmd=/usr/sbin/rc redirect start sh: /usr/sbin/uevent: not found rc_cmd=/usr/sbin/rc dnrd start redirect rc_cmd=/usr/sbin/rc ieee_802_1x start bind: Address already in use bind: Address already in use rc_cmd=/usr/sbin/rc srt restart rc_cmd=/usr/sbin/rc rp start Mar/10/2020 21:04:28: dhcp6_ctl_authinit: failed to open /tmp/dhcp6sctlkey: No such file or directory rc_cmd=/usr/sbin/rc udpecho start rc_cmd=/usr/sbin/rc ingress_qos start ScDrvDev_ioctl: CMD: (19) is not supported /usr/sbin/iq: failed to enable Ingress QoS rc_cmd=/usr/sbin/rc ingress_classify start rc_cmd=/usr/sbin/rc qos_remark start rc_cmd=/usr/sbin/rc ipv6wd start rc_cmd=/usr/sbin/rc pppoe_relay start rc_cmd=/usr/sbin/rc telnetd start rc_cmd=/usr/sbin/rc sshd start rc_cmd=/usr/sbin/rc igd_upnp start rc_cmd=/usr/sbin/rc dnsr start rc_cmd=/usr/sbin/rc cron start Could not load host key: /etc/ssh/ssh_host_ed25519_key rc_cmd=/usr/sbin/rc cwmp_stun start Erasing 128 Kibyte @ 20000 -- 0 % complete Erasing 128 Kibyte Smart Box GIGA login:


[ 0.000000] Linux version 5.15.45 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r19735+5-39bc566310) 11.3.0, GNU ld (GNU Binutils) 2.37) #0 SMP Mon Jun 20 14:55:19 2022 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is Beeline SmartBox GIGA [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] percpu: Embedded 11 pages/cpu s15632 r8192 d21232 u45056 [ 0.000000] pcpu-alloc: s15632 r8192 d21232 u45056 alloc=11*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=000380a8 [ 0.000000] Readback ErrCtl register=000380a8 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 248772K/262144K available (7068K kernel code, 621K rwdata, 1440K rodata, 1228K init, 242K bss, 13372K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000004] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns [ 0.016023] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.088357] pid_max: default: 32768 minimum: 301 [ 0.097730] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.112145] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.130589] rcu: Hierarchical SRCU implementation. [ 0.140413] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.156011] smp: Bringing up secondary CPUs ... [ 0.165786] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.165812] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.165827] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.165872] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.225800] Synchronize counters for CPU 1: done. [ 0.288061] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.288081] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.288092] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.288121] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.347009] Synchronize counters for CPU 2: done. [ 0.407371] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.407392] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.407403] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.407434] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.466603] Synchronize counters for CPU 3: done. [ 0.526208] smp: Brought up 1 node, 4 CPUs [ 0.538542] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.558037] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.571871] pinctrl core: initialized pinctrl subsystem [ 0.583441] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.596168] cpuidle: using governor teo [ 0.614746] FPU Affinity set after 11720 emulations [ 0.626530] clocksource: Switched to clocksource GIC [ 0.637189] NET: Registered PF_INET protocol family [ 0.647037] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.662026] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.678585] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.693755] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.707943] TCP: Hash tables configured (established 2048 bind 2048) [ 0.720649] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.733544] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.747664] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.758824] PCI: CLS 0 bytes, default 32 [ 0.769070] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.786216] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.797754] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.821429] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.832829] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.844204] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.855793] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 0.869076] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 0.886565] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0060000000 [ 0.902755] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 1.156516] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 1.170266] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 1.179927] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 1.189628] PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 1.203780] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 1.216298] pci_bus 0000:00: root bus resource [bus 00-ff] [ 1.227185] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 1.240822] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] [ 1.253145] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 1.265022] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.277467] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 1.289969] pci 0000:00:00.0: supports D1 [ 1.297837] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 1.310068] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 1.321949] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 1.334372] pci 0000:00:01.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 1.346905] pci 0000:00:01.0: supports D1 [ 1.354738] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 1.368070] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.383899] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 1.400065] pci 0000:01:00.0: [14c3:7663] type 00 class 0x000280 [ 1.411935] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit pref] [ 1.426235] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x00003fff 64bit pref] [ 1.440581] pci 0000:01:00.0: reg 0x20: [mem 0x00000000-0x00000fff 64bit pref] [ 1.455027] pci 0000:01:00.0: supports D1 D2 [ 1.463384] pci 0000:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 1.476567] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 1.507519] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 1.517810] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.529894] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff] [ 1.543373] pci 0000:00:00.0: bridge window [mem 0x00000000-0x000fffff pref] [ 1.557719] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.571110] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000 [ 1.582961] pci 0000:02:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 1.595506] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 1.608903] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 1.619187] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 1.631274] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff] [ 1.644755] pci 0000:00:01.0: bridge window [mem 0x00000000-0x000fffff pref] [ 1.659098] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 1.672283] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 1.685363] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.699187] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 1.712315] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.726139] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 1.739628] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x602fffff pref] [ 1.753963] pci 0000:00:01.0: BAR 8: assigned [mem 0x60300000-0x603fffff] [ 1.767449] pci 0000:00:01.0: BAR 9: assigned [mem 0x60400000-0x604fffff pref] [ 1.781780] pci 0000:00:00.0: BAR 1: assigned [mem 0x60500000-0x6050ffff] [ 1.795272] pci 0000:00:01.0: BAR 1: assigned [mem 0x60510000-0x6051ffff] [ 1.808753] pci 0000:00:00.0: BAR 7: assigned [io 0x0000-0x0fff] [ 1.820832] pci 0000:00:01.0: BAR 7: assigned [io 0x1000-0x1fff] [ 1.832939] pci 0000:01:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff 64bit pref] [ 1.848327] pci 0000:01:00.0: BAR 2: assigned [mem 0x60200000-0x60203fff 64bit pref] [ 1.863698] pci 0000:01:00.0: BAR 4: assigned [mem 0x60204000-0x60204fff 64bit pref] [ 1.879088] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.888921] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 1.901018] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 1.914493] pci 0000:00:00.0: bridge window [mem 0x60100000-0x602fffff pref] [ 1.928844] pci 0000:02:00.0: BAR 0: assigned [mem 0x60300000-0x603fffff] [ 1.942319] pci 0000:00:01.0: PCI bridge to [bus 02] [ 1.952162] pci 0000:00:01.0: bridge window [io 0x1000-0x1fff] [ 1.964255] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff] [ 1.977738] pci 0000:00:01.0: bridge window [mem 0x60400000-0x604fffff pref] [ 1.994203] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 2.008425] printk: console [ttyS0] disabled [ 2.016918] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 2.034841] printk: console [ttyS0] enabled [ 2.051380] printk: bootconsole [early0] disabled [ 2.070929] 1e000e00.uartlite3: ttyS1 at MMIO 0x1e000e00 (irq = 20, base_baud = 3125000) is a 16550A [ 2.092091] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 2.104816] nand: Macronix MX30LF1G18AC [ 2.112465] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.127568] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits [ 2.198194] scpart: Valid 'SC PART MAP' (12 partitions) found at 0x100000 [ 2.211806] 12 scpart partitions found on MTD device mt7621-nand [ 2.223774] Creating 12 MTD partitions on "mt7621-nand": [ 2.234363] 0x000000000000-0x000000100000 : "u-boot" [ 2.255576] 0x000000100000-0x000000200000 : "dynamic partition map" [ 2.279221] 0x000000200000-0x000000300000 : "Factory" [ 2.300657] 0x000000300000-0x000000400000 : "Boot Flag" [ 2.322299] 0x000000400000-0x000000a00000 : "kernel" [ 2.393738] 0x000000a00000-0x000001000000 : "Kernel 2" [ 2.465496] 0x000001000000-0x000002800000 : "File System 1" [ 2.719666] 0x000002800000-0x000004000000 : "File System 2" [ 2.973870] 0x000004000000-0x000004800000 : "Configuration/log" [ 3.067460] 0x000004800000-0x000005400000 : "application tmp buffer (Ftool)" [ 3.203715] 0x000005400000-0x000007c00000 : "container" [ 3.618659] 0x000007c00000-0x000007f80000 : "bad block reserved" [ 3.674797] Concatenating MTD devices: [ 3.682381] (0): "File System 1" [ 3.688835] (1): "Configuration/log" [ 3.695942] (2): "application tmp buffer (Ftool)" [ 3.705300] (3): "container" [ 3.711033] into device "ubi-concat" [ 3.718219] 1 fixed-partitions partitions found on MTD device ubi-concat [ 3.731561] Creating 1 MTD partitions on "ubi-concat": [ 3.741799] 0x000000000000-0x000005400000 : "ubi" [ 4.618065] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 4.634307] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 22 [ 4.652193] i2c_dev: i2c /dev entries driver [ 4.663791] NET: Registered PF_INET6 protocol family [ 4.675752] Segment Routing with IPv6 [ 4.683218] In-situ OAM (IOAM) with IPv6 [ 4.691146] NET: Registered PF_PACKET protocol family [ 4.701671] 8021q: 802.1Q VLAN Support v1.8 [ 4.715700] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 4.750738] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 4.767498] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx [ 4.777321] mt7530 mdio-bus:1f wan (uninitialized): PHY [mt7530-0:00] driver [MediaTek MT7530 PHY] (irq=24) [ 4.803747] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=25) [ 4.825826] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=26) [ 4.848607] DSA: tree 0 setup [ 4.857459] UBI: auto-attach mtd12 [ 4.864266] ubi0: attaching mtd12 [ 6.569075] ubi0: scanning is finished [ 6.593617] ubi0: attached mtd12 (name "ubi", size 84 MiB) [ 6.604622] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 6.618350] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 6.631872] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 6.645738] ubi0: good PEBs: 672, bad PEBs: 0, corrupted PEBs: 0 [ 6.657713] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 6.672098] ubi0: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 1655623215 [ 6.690300] ubi0: available PEBs: 0, total reserved PEBs: 672, PEBs reserved for bad PEB handling: 14 [ 6.708693] ubi0: background thread "ubi_bgt0d" started, PID 275 [ 6.711235] block ubiblock0_0: created from ubi0:0(rootfs) [ 6.731676] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 6.752514] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 6.770858] Freeing unused kernel image (initmem) memory: 1228K [ 6.782731] This architecture does not have kernel memory protection. [ 6.795574] Run /sbin/init as init process [ 6.803731] with arguments: [ 6.803739] /sbin/init [ 6.803745] with environment: [ 6.803750] HOME=/ [ 6.803755] TERM=linux [ 7.365183] init: Console is alive [ 7.372435] init: - watchdog - [ 8.332389] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 8.466740] usbcore: registered new interface driver usbfs [ 8.477871] usbcore: registered new interface driver hub [ 8.488611] usbcore: registered new device driver usb [ 8.509742] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator [ 8.524831] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator [ 8.540216] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 8.550867] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1 [ 8.576708] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010 [ 8.595003] xhci-mtk 1e1c0000.xhci: irq 21, io mem 0x1e1c0000 [ 8.607769] hub 1-0:1.0: USB hub found [ 8.615399] hub 1-0:1.0: 2 ports detected [ 8.624157] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 8.634900] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2 [ 8.649895] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed [ 8.662782] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 8.679958] hub 2-0:1.0: USB hub found [ 8.687616] hub 2-0:1.0: 1 port detected [ 8.703072] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 8.736985] init: - preinit - [ 9.522222] random: jshn: uninitialized urandom read (4 bytes read) [ 9.606264] random: jshn: uninitialized urandom read (4 bytes read) [ 9.656715] random: jshn: uninitialized urandom read (4 bytes read) [ 9.934957] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 9.951508] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 9.956803] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 9.981979] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 12.186775] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 12.198447] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 411 [ 12.281452] UBIFS (ubi0:1): recovery needed [ 12.499502] UBIFS (ubi0:1): recovery completed [ 12.508528] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 12.524125] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 12.543868] UBIFS (ubi0:1): FS size: 76185600 bytes (72 MiB, 600 LEBs), max 610 LEBs, journal size 3809280 bytes (3 MiB, 30 LEBs) [ 12.567083] UBIFS (ubi0:1): reserved for root: 3598434 bytes (3514 KiB) [ 12.580250] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 4BBF3597-B4DE-421F-B3F1-C51DFE70CDB8, small LPT model [ 12.607152] mount_root: switching to ubifs overlay [ 12.635540] urandom-seed: Seeding with /etc/urandom.seed [ 12.772907] procd: - early - [ 12.778960] procd: - watchdog - [ 13.446721] procd: - watchdog - [ 13.560504] procd: - ubus - [ 13.710652] urandom_read_iter: 7 callbacks suppressed [ 13.710688] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.735591] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.748841] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.768157] procd: - init - [ 14.624537] kmodloader: loading kernel modules from /etc/modules.d/* [ 14.833207] urngd: v1.0.2 started. [ 14.931610] Loading modules backported from Linux version v5.15.33-0-g06f50ca83ace [ 14.946807] Backport generated by backports.git v5.15.33-1-0-g183c4ab2 [ 15.038797] random: crng init done [ 15.045595] random: 23 urandom warning(s) missed due to ratelimiting [ 15.143708] pci 0000:00:01.0: enabling device (0000 -> 0003) [ 15.155088] mt7603e 0000:02:00.0: enabling device (0000 -> 0002) [ 15.167298] mt7603e 0000:02:00.0: ASIC revision: 76030010 [ 16.207876] mt7603e 0000:02:00.0: Firmware Version: ap_pcie [ 16.219025] mt7603e 0000:02:00.0: Build Time: 20160107100755 [ 16.266532] mt7603e 0000:02:00.0: firmware init done [ 16.445876] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht' [ 16.457434] pci 0000:00:00.0: enabling device (0000 -> 0003) [ 16.468780] mt7615e 0000:01:00.0: enabling device (0000 -> 0002) [ 16.494972] ieee80211 phy1: Selected rate control algorithm 'minstrel_ht' [ 16.549218] PPP generic driver version 2.4.2 [ 16.559854] NET: Registered PF_PPPOX protocol family [ 16.578770] kmodloader: done loading kernel modules from /etc/modules.d/* [ 18.142125] mt7615e 0000:01:00.0: mediatek/mt7663pr2h.bin not found, switching to mediatek/mt7663pr2h_rebb.bin [ 18.293080] mt7615e 0000:01:00.0: HW/SW Version: 0x65322d31, Build Time: 2009041715da1a1 [ 18.293080] [ 18.470291] mt7615e 0000:01:00.0: N9 Firmware Version: 7663mp1827, Build Time: 20200904171623 [ 18.487408] mt7615e 0000:01:00.0: Region number: 0x3 [ 18.497403] mt7615e 0000:01:00.0: Parsing tailer Region: 0 [ 18.511604] mt7615e 0000:01:00.0: Region 0, override_addr = 0x00112c00 [ 18.524762] mt7615e 0000:01:00.0: Parsing tailer Region: 1 [ 18.536869] mt7615e 0000:01:00.0: Parsing tailer Region: 2 [ 18.548318] mt7615e 0000:01:00.0: override_addr = 0x00112c00, option = 3 [ 25.442218] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 25.468985] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 25.485622] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 25.489096] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 25.517463] br-lan: port 1(lan1) entered blocking state [ 25.527976] br-lan: port 1(lan1) entered disabled state [ 25.540614] device lan1 entered promiscuous mode [ 25.549938] device eth0 entered promiscuous mode [ 25.564068] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 25.602056] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 25.617404] br-lan: port 2(lan2) entered blocking state [ 25.627915] br-lan: port 2(lan2) entered disabled state [ 25.640752] device lan2 entered promiscuous mode [ 25.696679] mt7530 mdio-bus:1f wan: configuring for phy/gmii link mode [ 810.414812] mt7530 mdio-bus:1f lan1: Link is Up - 1Gbps/Full - flow control rx/tx [ 810.429836] br-lan: port 1(lan1) entered blocking state [ 810.440275] br-lan: port 1(lan1) entered forwarding state [ 810.451901] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready


OpenWrt unofficial firmware

Breed bootloader

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 11:13
  • by 127.0.0.1