Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Next revision
Previous revision
Next revisionBoth sides next revision
ru:toh:asus:wl500gp [2014/07/03 06:14] – created johnny8921.gmail.comru:toh:asus:wl500gp [2018/03/03 20:34] – ↷ Links adapted because of a move operation
Line 1: Line 1:
 +====== ASUS WL-500g Premium ======
  
 +В линейке <wrap em>WL-500g Premium</wrap> выпущены две модели: ''[[http://www.asus.com/ru/Networking/WL500g_Premium/|ASUS WL-500g Premium]]'', она же ''ASUS WL-500gP V1'', и ''[[http://www.asus.com/ru/Networking/WL500gP_V2/specifications/|ASUS WL-500gP V2]]''. У разных моделей разные процессоры.
 +
 +ASUS WL-500gP является одним из лучших маршрутизаторов с Linux на борту: большие объёмы RAM и Flash, два порта USB 2.0 и быстрый процессор. В V1 есть miniPCI слот, который позволяет менять радиомодуль. В V2 убран miniPCI слот и полностью обновлена элементная база, которая стала компактней и с меньшим энергопотреблением.
 +
 +===== Поддерживаемые версии =====
 +^ Версия/Модель ^ S/N ^ Версия OpenWrt  ^ Примечание ^
 +| v1 | - | Backfire 10.03 и новее | Радиомодуль в miniPCI слоте, заменяем ;\\ антенна   **слева** (если смотреть с лицевой стороны) |
 +| v2 | - | Backfire 10.03 и новее | Большинство элементов встроены в  SoC;\\ антенна **справа** (если смотреть с лицевой стороны) |
 +
 +**Note:** Релиз Chaos Calmer 15.05.1 нормально работает на обоих версиях маршрутизатора.
 +
 +**Note:** Все старые сведения и остальные догадки и замечания вида "По-моему работает, но вот это не работает" читайте [[toh:asus:wl500gp|на английском]].
 +
 +===== Hardware Highlights =====
 +^ версия ^ CPU ^ Ram ^ Flash ^ Сеть ^ USB ^ Serial ^ JTag ^
 +| v1 | Broadcom BCM4704@264Mhz | 32MiB | 8MiB | 4 x 1 | 2x 2.0 | Yes | No |
 +| v2 | Broadcom BCM5354@240Mhz | 32MiB | 8MiB | 4 x 1 | 2x 2.0 | Yes | No |
 +
 +===== Установка =====
 +
 +Этот раздел содержит инструкции по установке и обновлению OpenWrt.  Сначала мы даем ссылки на скачивание файлов, а ниже будет инструкция по установке.
 +
 +==== Выбираем правильный образ ===
 +=== Backfire (10.03.1) ===
 +WL-500gP поддерживает 2 версии:
 +  *[[http://downloads.openwrt.org/backfire/10.03/brcm-2.4/openwrt-brcm-2.4-squashfs.trx|brcm-2.4]]
 +    * Использует устаревшее ядро 2.4
 +    * Использует только драйвер broadcom для поддержки радиомодуля в v2.
 +    * **РЕКОМЕНДУЕТСЯ ДЛЯ  v2**
 +  *[[http://downloads.openwrt.org/backfire/10.03/brcm47xx/openwrt-brcm47xx-squashfs.trx|brcm47xx]]
 +    * Использует ядро 2.6, Это быстрей и больше функций
 +    * Использует open source драйвер b43, который не всегда корректно работает на v2
 +    * **РЕКОМЕНДУЕТСЯ ДЛЯ v1**
 +    * Upgrade with [[http://downloads.openwrt.org/backfire/10.03.1/brcm47xx/openwrt-brcm47xx-squashfs.trx|brcm47xx Backfire 10.03.1]] works seamlessy on V.1, with restored config from 10.03
 +
 +=== Attitude adjustment (12.09) ===
 +  *[[http://downloads.openwrt.org/attitude_adjustment/12.09/brcm47xx/generic/|brcm47xx/53xx]]
 +    * Использует ядро 3.3.8
 +    * Быстрее предыдущих версий, потребляет больше RAM памяти, больше функций доступно
 +    * Может использовать любой open source broadcom драйвер хоть wl, хоть b43.
 +
 +=== Chaos Calmer (15.05) ===
 +  *[[https://downloads.openwrt.org/chaos_calmer/15.05/brcm47xx/generic/openwrt-15.05-brcm47xx-generic-squashfs.trx | brcm47xx trx image]]
 +    * Использует ядро 3.18.20
 +    * Протестировано 15.09.2015 на V1, установлено с помощью sysupgrade поверх 14.07.
 +  *  [[https://downloads.openwrt.org/chaos_calmer/15.05/brcm47xx/legacy/openwrt-15.05-brcm47xx-legacy-asus-wl-500gp-v1-squashfs.trx | brcm47xx legacy ASUS WL-500gP V1 trx image]], [[https://downloads.openwrt.org/chaos_calmer/15.05/brcm47xx/legacy/openwrt-15.05-brcm47xx-legacy-asus-wl-500gp-v2-squashfs.trx | brcm47xx legacy ASUS WL-500gP V2 trx image]] — Установка из веб-интерфейса заводской прошивки.
 +
 +=== Chaos Calmer (15.05.1) ===
 +ASUS WL-500gP V1
 +  *[[https://downloads.openwrt.org/chaos_calmer/15.05.1/brcm47xx/legacy/openwrt-15.05.1-brcm47xx-legacy-asus-wl-500gp-v1-squashfs.trx | firmware upgrade trx image]]
 +
 +ASUS WL-500gP V2
 +  *[[https://downloads.openwrt.org/chaos_calmer/15.05.1/brcm47xx/legacy/openwrt-15.05.1-brcm47xx-legacy-asus-wl-500gp-v2-squashfs.trx | firmware upgrade trx image]]
 +    * Использует ядро 3.18.23
 +    * Протестировано 24.04.2016 на V2, установлено из стоковой прошивки стандартной процедурой обновления.
 +==== OEM простая установка ====
 +Начиная с OpenWRT Chaos Calmer 15.05 загружаем образ openwrt-*-brcm47xx-legacy-asus-wl-500gp-v?-squashfs.trx на странице обновления маршрутизатора, кликаем "Загрузить" и дожидаемся обновления странички.
 +
 +**Примечания.**
 +  - Не перезагружайте маршрутизатор во избежание его окирпичивания.
 +  - Настройки заводской прошивки не сохранятся.
 +  - Если адрес IP был изменён, после обновления до OpenWRT адрес будет стандартный 192.168.1.1
 +==== OEM установка используя TRX  ====
 +Не работает. Старый метод который практически не используется и утилиту нужно давно переписать (Sep. 1st 2007, confirmed by nbd on IRC).
 +
 +FIXME does this still apply? --- //KanjiMonster 2010/04/11 13:13//
 +
 +TEST STILL FAILS on ASUS WL-500g Premium V2 with newest ASUS Firmware version 3.0.4.4 --- //porter 2011/04/28 00:18//
 +
 +TEST STILL FAILS on ASUS WL-500g Premium V1 with ASUS Firmware (not sure about the version)  --- //sup 2012/05/05 20:22//
 +
 +==== OEM установка посредством TFTP ====
 +
 +Для установки OpenWrt используя TFTP или ASUS firmware restoration tool вы должны перевести роутер в диагностический режим.
 +
 +**Note:** В диагностическом режиме маршрутизатор принимает адрес IP, хранящийся в энергонезависимой памяти, обычно это 192.168.1.1, но если вы его меняли, возможно, адрес будет другой.
 +
 +После установки прошивки адрес будет 192.168.1.1. В дальнейшем весь код будет относиться к IP 192.168.1.1
 +
 +Для перевода маршрутизатора в диагностический режим:
 +
 +  * Отключите шнур питания от маршрутизатора.
 +  * Проверьте, что на вашем компьютере установлен адрес IP 192.168.1.10 (не используйте .1).
 +  * Подключите компьютер к маршрутизатора в любой LAN порт.
 +  * Нажмите палочкой (ручкой, карандашом) черную кнопку RESTORE с задней стороны роутера и держите ее нажатой.
 +  * Вставьте разъём питания и, подождав 10 секунд, отпустите кнопку RESTORE.
 +  * Если вы увидели медленно мигающий светодиод POWER, это означает, что маршрутизатор в диагностическом режиме. Теперь он доступен по TFTP или из ASUS firmware restoration tool.
 +
 +== TFTP ==
 +
 +Когда маршрутизатор находится в диагностическом режиме, можно установить OpenWrt, используя клиент TFTP.
 +
 +  * Выполните команды (в примере указан адрес маршрутизатора 192.168.1.1, он может быть другим - см. замечание выше):
 +    * Linux, *BSD or Mac OS X
 + <code>
 +tftp 192.168.1.1
 +tftp> binary
 +tftp> trace
 +tftp> put openwrt-brcm-2.4-squashfs.trx</code>
 +    * Windows
 +    <code>tftp -i 192.168.1.1 PUT openwrt-brcm-2.4-squashfs.trx</code>
 +  * Во время загрузки один из индикаторов будет часто мигать (в такт обмену пакетами).
 +  * После того как загрузка прошивки завершена, подождите не меньше 6 минут. Сначала прошивка записывается в ОЗУ, затем прошивается в микросхему FLASH. Поэтому, если вы не хотите получить кирпич, подождите минут 10. Можете проверять готовность, пытаясь подключиться к его порту 80/TCP или 22/TCP.
 +  * Маршрутизатор презагрузитсья автоматически после завершения загрузки. Перезагрузка занимает некоторое время. Если перезагрузка не произошла автоматически, вы должны перезагрузить его вручную. Перед этим обязательно подождите время для безопасной прошивки.
 +  * Вы это сделали! Теперь попробуйте постучаться на роутер PINGом, а после уже TELNETом IP адресс: 192.168.1.1 - даже если вы использовали ранее другой) и приступайте к настройке.
 +**NOTES:**
 +  * В Windows 7 по умолчанию не установлен tftp клиент, вам нужно установить его отдельно (в остнастке панели управления "Программы и компоненты"). В более ранних версиях Windows он установлен по умолчанию.
 +  * Если TFTP не работает, то используйте atftp.
 +  * После успешной TFTP загрузки, НЕ ПЕРЕЗАГРУЖАЙТЕ РОУТЕР СРАЗУ! Можете превратить его в кирпич.
 +
 +== Automated Ping and TFTP Script ==
 +  * See: https://gist.github.com/3748339
 +  * Requires atftp
 +  <code>./ping_atftp 192.168.1.1 openwrt-brcm-2.4-squashfs.trx</code>
 +
 +== ASUS firmware restoration tool (Windows only) ==
 +Если ваша ОС Windows, то это рекомендуемый для Вас метод. Утилита поставляется на диске с роутером, или на сайте производителя. Для обновления необходимо перевести роутер в диагностический режим.
 +
 +  * Запустите программу.
 +  * Укажите на .trx файл (openwrt-brcm-2.4-squashfs.trx).
 +  * Зажмите "Загрузить". После установки роутер автоматически перезагрузиться. Установка и перезагрузка занимают какое время. Не перезагружайте и не вынимайте шнур питания если ваш роутер не перезагрузился раньше, чем через 10 минут.
 +  * Вы это сделали! Теперь попробуйте постучаться на роутер PINGом, а после уже TELNETом IP адресс: 192.168.1.1 - даже если вы использовали ранее другой) и приступайте к настройке.
 +
 +===== Upgrading OpenWrt =====
 +
 +If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing.
 +
 +== LuCI Web Upgrade Process ==
 +
 +FIXME use correct URL
 +  *Browse to http://192.168.1.1/cgi-bin/luci/mini/system/upgrade/ LuCI Upgrade URL
 +  *Upload TRX file to LuCI
 +  *Wait for reboot
 +
 +== Terminal Upgrade Process ==
 +
 +  *Login as root via SSH on 192.168.1.1
 +  *Use the following commands to upgrade.
 +
 +<code>
 +cd /tmp/
 +wget http://downloads.openwrt.org/latest/brcm-2.4/openwrt-brcm-2.4-squashfs.trx
 +sysupgrade /tmp/openwrt-brcm-2.4-squashfs.trx</code>
 +
 +If this does not work (reboot without change) try using mdt. Make sure "linux" is the correct mtd target! (cat /proc/mtd). Tested with v1 models.
 +<code>
 +cd /tmp/
 +wget [link to image]
 +mtd -r write /tmp/[image].trx linux
 +</code>
 +
 +
 +
 +
 +
 +===== Hardware =====
 +==== Info ====
 +| **Version:** | v1 | v2 |
 +| **[[wp>Instruction set|Architecture]]:**    | [[wp>MIPS architecture|MIPS]] | [[wp>MIPS architecture|MIPS]] |
 +| **Vendor:**          | [[wp>Broadcom]] | [[wp>Broadcom]] |
 +| **[[docs:techref:bootloader]]:**     | [[docs:techref:bootloader:cfe]] | [[docs:techref:bootloader:cfe]] |
 +| **[[docs:hardware:soc|System-On-Chip]]:**  | Broadcom BCM4704 | Broadcom BCM5354 |
 +| **[[docs:hardware:cpu|CPU]]/Speed**  | BMIPS3300 V0.6 / 264 MHz | :?: / 240 MHz |
 +| **Flash-Chip:** | EON EN29LV302B-70TCP\\ Spansion S29GL064A90TFIR7 | Macronix 29LV640DB |
 +| **Flash size:** | 8 MiB | 8 MiB |
 +| **RAM-Chips:** | HY5DU281622FTP-5 / DDR-400 | :?: |
 +| **RAM size:** | 32* MiB | 32 MiB |
 +| **Wireless:** | Broadcom BCM4318 802.11b/g (miniPCI) | Broadcom BCM43xx 802.11b/g (integrated) |
 +| **Ethernet:** | Robo switch {{:media:datasheets:bcm5325_pinout.png?linkonly|BCM5325E}} | Switch in CPU |
 +| **USB:** | 2x 2.0 [[http://www.via.com.tw/en/products/peripherals/usb/vt6212l/|Via VT6212L]]| 2x 2.0 |
 +| **Power adapter** | 5V DC 2.5 A / UMEC UP0181B-05PE | :?: |
 +| **[[docs:hardware:port.serial|Serial]]:** | [[#Serial|Yes]] | [[#Serial|Yes]] | 
 +| **[[docs:hardware:port.jtag|JTAG]]:** | No | Yes (pinout same as wrt54G) |
 +
 +* some older models have only 16 MiB enabled.
 +
 +==== Photos ====
 +
 +[[:oldwiki:openwrtdocs:hardware:asus/wl500gp/img_0007|{{oldwiki:openwrtdocs:hardware:asus:wl500gp:img_0007.jpg?320}}]]\\  With a Atheros Wistron CM9\\  MiniPCI WiFi card
 +
 +[[:oldwiki:openwrtdocs:hardware:asus/wl500gp/img_3505|{{oldwiki:openwrtdocs:hardware:asus:wl500gp:img_3505.jpg?320}}]]\\  With a Gigabyte GN-WIAG02 (168c:0013)\\ 802.11abg MiniPCI WiFi card (Atheros AR5212) and 2nd antenna
 +
 +==== Открытие корпуса ====
 +
 +**Note:** Это действие лишает гарантии
 +
 +Уберите 4 резиновые заглушки на ногах, под ними будет 4 винта откручиваем и поддеваем верхнюю крышку. Должна сниматься без особых усилий.
 +
 +==== Последовательный порт ====
 +=== V1 ===
 +
 +Последовательный порт готов к пайке (подгтовлен под 8-pin коннектор для подключения data-кабеля) в центре и правее верхней части. Смотри фото
 +Если не понятно по фото то ниже будет распиновка (V1):
 +| RESET |  | 
 +| GND | 3.3V_OUT | 
 +| UART_TX1 | UART_TX0 | 
 +| UART_RX1 | UART_RX0 | 
 +Pin 1 (with the square solder pad) is RX0.
 +
 +{{media:asus:wl500gpv1_serial.jpg?500x250|}}
 +=== V2 ===
 +Для (V2) tts/0 это J4 площадка под пайку:
 +| 3.3V_OUT |
 +| UART_RX0 |
 +| UART_TX0 |
 +| GND |
 +3.3V_OUT это вход рядом с подписью J4 и этот вход ближе к голотипу ASUS.
 +
 +В V1 COM-порт CMOS уровня, поэтому Вам понадобится VCC, что бы прийти к стандартному COM. Параметры 115200 baud and 8-n-1.
 +
 +Для подключени через COM V2, VCC Вам не нужен. TX COMa в UART_RX0 pin, RX COMa в UART_TX0 pin. Вот журнал загрузки через COM
 + /backfire/10.03.1/brcm47xx/openwrt-brcm47xx-squashfs.trx
 +
 +==== Buttons ====
 +The ASUS WL-500g Premium has two buttons. They are RESTORE and EZSETUP. The buttons can be used with hotplug events. E. g. [#wifitoggle WiFi toggle].
 +^ BUTTON ^ Event ^
 +| RESTORE | reset | 
 +| EZSETUP | ses | 
 +
 +ACTION: released or pressed
 +
 +
 +===== Замена радиомодуля =====
 +
 +**Note:** Только v1 !
 +
 +Стандартный радиомодуль это MiniPCI карта BCM4318. Некоторые меняют эту карту на Atheros. Эта карта работает на драйвере с открытым исходным кодом, что позволяет работать на ядре 2.6
 +Для того что бы заменить карточку необходимо открыть роутер, отсоединить антенный кабель от карточки, аккуратно отогнуть две защелки и достать карту. После это го вся операция повторяется в обратном порядке с новой картой.  
 +Установите пакеты kmod-madwifi и hostapd-mini что бы добавить новый беспроводной адаптер. 
 +
 +Отредактируйте ваш  /etc/config/wireless добавив в конце:
 +
 +| ''config 'wifi-device' 'wifi0'
 +        option 'type' 'atheros'
 +
 +config 'wifi-iface'
 +        option 'device' 'wifi0''' |
 +
 +Зайдите  [[http://sr.uz/index.php?p=223&more=1&c=1&tb=1&pb=1|сюда]] там больше примеров.
 +
 +После установки kmod-madwifi вы можете автоматически создать стандартный файл /etc/config/wireless для Atheros:
 +
 +<code>
 +opkg update
 +opkg install kmod-madwifi wpad-mini
 +rm -f /etc/config/wireless
 +wifi detect > /etc/config/wireless
 +</code>
 +
 +
 +===== Specific Configuration =====
 +==== Interfaces ====
 +The default network configuration is:
 +^ Interface Name ^ Description ^ Default configuration ^
 +| br-lan | LAN & WiFi | 192.168.1.1/24 | 
 +| vlan0 | LAN ports (1 to 4) |  | 
 +| vlan1 | WAN port | DHCP | 
 +| wl0/ath0 | WiFi | Disabled by default | 
 +
 +
 +LAN and WiFi is bridged to br-lan. WiFi is disabled by default for security reasons (to prevent an open access point).
 +===== Switch Ports (for VLANs) =====
 +Please note that the link between the physical ports and switch ports is different for v1 and v2 routers (see table below). 
 +
 +^ Port ^ Switch port (v1) ^ Switch port (v2) ^
 +| Internet (WAN) | 0 | 4 | 
 +| LAN 1 | 1 | 3 | 
 +| LAN 2 | 2 | 2 | 
 +| LAN 3 | 3 | 1 | 
 +| LAN 4 | 4 | 0 | 
 +| Internal connection | 5 | 5 | 
 +
 +5 is the internal connection to the router itself. Don't be fooled: Port 1 on the v2 unit is number 3 when configuring VLANs. vlan0 = eth0.0, vlan1 = eth0.1 and so on. For v1 unit, WAN is switch port 0. LAN ports are switch ports 1,2,3,4.  And LAN ports map exactly to switch ports.
 +
 +===== Failsafe mode =====
 +
 +If you forgot your password, broken one of the startup scripts, firewalled yourself or corrupted the JFFS2 partition, you can get back in by using OpenWrt's [[docs:user-guide:troubleshooting:failsafe_and_factory_reset|failsafe mode]].
 +
 +==== Boot into failsafe mode ====
 +  * Unplug the router's power cord.
 +  * Connect the router's LAN1 port directly to your PC.
 +  * Configure your PC with a static IP address between 192.168.1.2 and 192.168.1.254. E. g. 192.168.1.2 (gateway and DNS is not required).
 +  * Plug the power on and wait for the power LED to switch off
 +  * While the power LED is off press any button (RESTORE and EZSETUP will work) a few times
 +  * Power LED goes fast-blinking (about 1 time per second)
 +  * You should be able to telnet to the router at 192.168.1.1 now (no username and password)
 +
 +
 +===== Активация всей RAM =====
 +*Note:* Это актуально только для WL-500gP v1.
 +
 +На новых  ASUS WL-500g Premium вся память активирована по умолчанию. Если вы посмотрите "dmesg | grep Memory", то можете увидеть 16MiB of RAM. В спецификации указано 32MiB. Для активации 32MiB меняет sdram_init и sdram_ncdl NVRAM переменные на:
 +
 +<code>
 +nvram set sdram_init=0x0009
 +nvram set sdram_ncdl=0x10308
 +nvram commit
 +reboot
 +</code>
 +Note:
 +  * В этом нет необходимости если у Вас 10.03.1 и V1 (BCM4704) - Может быть нужно для BCM4780?  --- //sup 2012/05/05 21:02//
 +  * using a "attitude_adjustment" (beta or trunk) brcm47xx image it looks required. Otherwise you may get a memory dump while executing opkg install ... (just a "Killed"). -- ''validom 2012/11/14''
 +
 +
 +===== Basic configuration =====
 +Since this part is identical for all devices, see [[docs:guide-quick-start:checks_and_troubleshooting|Basic configuration]].
 +
 +===== Connect stuff to the USB port =====
 +To connect stuff to the USB port, please see [[docs:guide-user:hardware:usb.overview|Connect stuff to the USB port]], the package kmod-usb2 is needed. For some devices the package kmod-usb-uhci-iv might also be needed.
 +
 +===== Hardware Mods =====
 +nothing?
 +===== Bootlogs =====
 +==== V1 Attitude Adjustment bootlog ====
 +<WRAP bootlog>
 +<nowiki>root@OpenWrt:/# dmesg 
 +[    0.000000] Linux version 3.3.8 (blogic@Debian-60-squeeze-64-minimal) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 Sat Mar 23 16:01:31 UTC 2013
 +[    0.000000] CPU revision is: 00029006 (Broadcom BMIPS3300)
 +[    0.000000] bcm47xx: using ssb bus
 +[    0.000000] ssb: Found chip with id 0x4704, rev 0x09 and package 0x00
 +[    0.000000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x03, vendor 0x4243)
 +[    0.000000] ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
 +[    0.000000] ssb: Core 2 found: Fast Ethernet (cc 0x806, rev 0x06, vendor 0x4243)
 +[    0.000000] ssb: Core 3 found: USB 1.1 Hostdev (cc 0x808, rev 0x03, vendor 0x4243)
 +[    0.000000] ssb: Core 4 found: PCI (cc 0x804, rev 0x08, vendor 0x4243)
 +[    0.000000] ssb: Core 5 found: MIPS 3302 (cc 0x816, rev 0x03, vendor 0x4243)
 +[    0.000000] ssb: Core 6 found: V90 (cc 0x807, rev 0x02, vendor 0x4243)
 +[    0.000000] ssb: Core 7 found: IPSEC (cc 0x80B, rev 0x00, vendor 0x4243)
 +[    0.000000] ssb: Core 8 found: MEMC SDRAM (cc 0x80F, rev 0x02, vendor 0x4243)
 +[    0.000000] ssb: chipcommon status is 0x0
 +[    0.000000] ssb: Initializing MIPS core...
 +[    0.000000] ssb: set_irq: core 0x0806, irq 4 => 4
 +[    0.000000] ssb: set_irq: core 0x0806, irq 5 => 5
 +[    0.000000] ssb: set_irq: core 0x0808, irq 6 => 2
 +[    0.000000] ssb: set_irq: core 0x0804, irq 2 => 6
 +[    0.000000] ssb: after irq reconfiguration
 +[    0.000000] ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I 
 +[    0.000000] ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I 
 +[    0.000000] ssb: core 0x0806, irq : 2(S)  3  4  5* 6  D  I 
 +[    0.000000] ssb: core 0x0808, irq : 2(S)* 3  4  5  6  D  I 
 +[    0.000000] ssb: core 0x0804, irq : 2(S)  3  4  5  6* D  I 
 +[    0.000000] ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I 
 +[    0.000000] ssb: core 0x0807, irq : 2(S)* 3  4  5  6  D  I 
 +[    0.000000] ssb: core 0x080b, irq : 2(S)* 3  4  5  6  D  I 
 +[    0.000000] ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
 +[    0.000000] found parallel flash.
 +[    0.000000] Unsupported SPROM revision 0 detected. Will extract v1
 +[    0.000000] ssb: Sonics Silicon Backplane found at address 0x18000000
 +[    0.000000] Serial init done.
 +[    0.000000] gpiochip_add: registered GPIOs 0 to 15 on device: bcm47xx
 +[    0.000000] Determined physical RAM map:
 +[    0.000000]  memory: 02000000 @ 00000000 (usable)
 +[    0.000000] Initrd not found or empty - disabling initrd
 +[    0.000000] Zone PFN ranges:
 +[    0.000000]   Normal   0x00000000 -> 0x00002000
 +[    0.000000] Movable zone start PFN for each node
 +[    0.000000] Early memory PFN ranges
 +[    0.000000]     0: 0x00000000 -> 0x00002000
 +[    0.000000] On node 0 totalpages: 8192
 +[    0.000000] free_area_init_node: node 0, pgdat 802da6d0, node_mem_map 81000000
 +[    0.000000]   Normal zone: 64 pages used for memmap
 +[    0.000000]   Normal zone: 0 pages reserved
 +[    0.000000]   Normal zone: 8128 pages, LIFO batch:0
 +[    0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
 +[    0.000000] pcpu-alloc: [0] 0 
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
 +[    0.000000] Kernel command line:  root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
 +[    0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
 +[    0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
 +[    0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
 +[    0.000000] Primary instruction cache 16kB, VIPT, 2-way, linesize 16 bytes.
 +[    0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +[    0.000000] Memory: 29100k/32768k available (2540k kernel code, 3668k reserved, 379k data, 168k init, 0k highmem)
 +[    0.000000] NR_IRQS:128
 +[    0.000000] console [ttyS0] enabled
 +[    0.004000] Calibrating delay loop... 262.14 BogoMIPS (lpj=524288)
 +[    0.048000] pid_max: default: 32768 minimum: 301
 +[    0.052000] Mount-cache hash table entries: 512
 +[    0.060000] NET: Registered protocol family 16
 +[    0.096000] bio: create slab <bio-0> at 0
 +[    0.108000] Switching to clocksource MIPS
 +[    0.124000] ssb: PCIcore in host mode found
 +[    0.432000] PCI host bridge to bus 0000:00
 +[    0.436000] pci_bus 0000:00: root bus resource [mem 0x40000000-0x7fffffff]
 +[    0.444000] pci_bus 0000:00: root bus resource [io  0x0100-0x07ff]
 +[    0.448000] pci 0000:00:00.0: [14e4:4704] type 0 class 0x000600
 +[    0.448000] PCI: Fixing up bridge 0000:00:00.0
 +[    0.452000] pci 0000:00:00.0: setting latency timer to 64
 +[    0.452000] PCI: Fixing up device 0000:00:00.0
 +[    0.456000] PCI: Fixing latency timer of device 0000:00:00.0 to 168
 +[    0.464000] pci 0000:00:00.0: reg 10: [mem 0x00000000-0x00001fff]
 +[    0.464000] pci 0000:00:00.0: reg 14: [mem 0x00000000-0x07ffffff pref]
 +[    0.464000] pci 0000:00:02.0: [14e4:4318] type 0 class 0x000280
 +[    0.464000] pci 0000:00:02.0: reg 10: [mem 0x00000000-0x00001fff]
 +[    0.464000] pci 0000:00:03.0: [1106:3038] type 0 class 0x000c03
 +[    0.464000] pci 0000:00:03.0: reg 20: [io  0xfce0-0xfcff]
 +[    0.464000] pci 0000:00:03.0: supports D1 D2
 +[    0.464000] pci 0000:00:03.0: PME# supported from D0 D1 D2 D3hot
 +[    0.464000] pci 0000:00:03.1: [1106:3038] type 0 class 0x000c03
 +[    0.464000] pci 0000:00:03.1: reg 20: [io  0xfce0-0xfcff]
 +[    0.464000] pci 0000:00:03.1: supports D1 D2
 +[    0.464000] pci 0000:00:03.1: PME# supported from D0 D1 D2 D3hot
 +[    0.464000] pci 0000:00:03.2: [1106:3104] type 0 class 0x000c03
 +[    0.468000] pci 0000:00:03.2: reg 10: [mem 0x00000000-0x000000ff]
 +[    0.468000] pci 0000:00:03.2: supports D1 D2
 +[    0.468000] pci 0000:00:03.2: PME# supported from D0 D1 D2 D3hot
 +[    0.472000] pci 0000:00:02.0: BAR 0: assigned [mem 0x40000000-0x40001fff]
 +[    0.480000] pci 0000:00:03.2: BAR 0: assigned [mem 0x40002000-0x400020ff]
 +[    0.488000] pci 0000:00:03.0: BAR 4: assigned [io  0x0400-0x041f]
 +[    0.492000] pci 0000:00:03.1: BAR 4: assigned [io  0x0420-0x043f]
 +[    0.504000] PCI: Enabling device 0000:00:02.0 (0000 -> 0002)
 +[    0.512000] PCI: Fixing up device 0000:00:02.0
 +[    0.516000] b43-pci-bridge 0000:00:02.0: setting latency timer to 64
 +[    0.536000] ssb: Found chip with id 0x4318, rev 0x02 and package 0x02
 +[    0.540000] ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x0D, vendor 0x4243)
 +[    0.540000] ssb: Core 1 found: IEEE 802.11 (cc 0x812, rev 0x09, vendor 0x4243)
 +[    0.540000] ssb: Core 2 found: PCI (cc 0x804, rev 0x0C, vendor 0x4243)
 +[    0.540000] ssb: Core 3 found: PCMCIA (cc 0x80D, rev 0x07, vendor 0x4243)
 +[    0.560000] ssb: chipcommon status is 0x0
 +[    0.564000] ssb: SPROM offset is 0x1000
 +[    0.568000] ssb: SPROM revision 2 detected.
 +[    0.588000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:02.0
 +[    0.600000] NET: Registered protocol family 2
 +[    0.604000] IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.612000] TCP established hash table entries: 1024 (order: 1, 8192 bytes)
 +[    0.620000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +[    0.624000] TCP: Hash tables configured (established 1024 bind 1024)
 +[    0.632000] TCP reno registered
 +[    0.636000] UDP hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.640000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
 +[    0.648000] NET: Registered protocol family 1
 +[    0.652000] PCI: CLS 0 bytes, default 16
 +[    0.664000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
 +[    0.668000] JFFS2 version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
 +[    0.680000] msgmni has been set to 56
 +[    0.684000] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254)
 +[    0.692000] io scheduler noop registered
 +[    0.696000] io scheduler deadline registered (default)
 +[    0.704000] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
 +[    0.732000] serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
 +[    0.760000] serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
 +[    0.804000] serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
 +[    0.832000] serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
 +[    0.844000] bcm47xx_pflash: flash init: 0x1c000000 0x02000000
 +[    0.852000] Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x001301
 +[    0.860000] Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
 +[    0.864000] Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
 +[    0.864000] Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
 +[    0.864000] Amd/Fujitsu Extended Query Table at 0x0040
 +[    0.868000]   Amd/Fujitsu Extended Query version 1.3.
 +[    0.872000] number of CFI chips: 1
 +[    0.876000] bcm47xx_pflash: Flash device: 0x2000000 at 0x1fc00000
 +[    0.884000] bcm47xx_part: bootloader size: 262144
 +[    0.892000] bcm47xx_part: Looking for dual image
 +[    0.900000] bcm47xx_part: TRX offset : 0
 +[    0.904000] 4 bcm47xx partitions found on MTD device Physically mapped flash
 +[    0.912000] Creating 4 MTD partitions on "Physically mapped flash":
 +[    0.920000] 0x000000000000-0x000000040000 : "cfe"
 +[    0.932000] 0x000000040000-0x0000007f0000 : "linux"
 +[    0.940000] 0x000000133c00-0x0000007f0000 : "rootfs"
 +[    0.944000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +[    0.964000] mtd: partition "rootfs" set to be root filesystem
 +[    0.968000] mtd: partition "rootfs_data" created automatically, ofs=310000, len=4E0000 
 +[    0.976000] 0x000000310000-0x0000007f0000 : "rootfs_data"
 +[    0.988000] 0x0000007f0000-0x000000800000 : "nvram"
 +[    1.000000] bcm47xx_sflash: error registering platform driver: -19
 +[    1.008000] bcm47xx_nflash: error registering platform driver: -19
 +[    1.016000] b44: Broadcom 44xx/47xx 10/100 PCI ethernet driver version 2.0
 +[    1.028000] b44 ssb0:0: eth0: Broadcom 44xx/47xx 10/100 PCI ethernet driver 00:1e:8c:02:35:7f
 +[    1.044000] b44 ssb0:1: eth1: PHY Reset would not complete
 +[    1.048000] b44 ssb0:1: eth1: Broadcom 44xx/47xx 10/100 PCI ethernet driver 40:10:18:00:00:2d
 +[    1.060000] BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
 +[    1.068000] TCP cubic registered
 +[    1.072000] NET: Registered protocol family 17
 +[    1.076000] Bridge firewalling registered
 +[    1.080000] 8021q: 802.1Q VLAN Support v1.8
 +[    1.096000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
 +[    1.104000] Freeing unused kernel memory: 168k freed
 +[    4.320000] diag: Detected 'ASUS WL-500g Premium'
 +[    4.376000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
 +[    4.384000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
 +[    5.520000] roboswitch: Probing device eth0: found a 5325! It's a 5350.
 +[   12.808000] JFFS2 notice: (351) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 6 of xref (0 dead, 2 orphan) found.
 +[   13.204000] b44 ssb0:0: eth0: powering down PHY
 +[   17.316000] Compat-drivers backport release: compat-drivers-2012-09-04-2-gddac993
 +[   17.324000] Backport based on wireless-testing.git master-2012-09-07
 +[   17.332000] compat.git: wireless-testing.git
 +[   17.392000] cfg80211: Calling CRDA to update world regulatory domain
 +[   17.396000] cfg80211: World regulatory domain updated:
 +[   17.404000] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
 +[   17.412000] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   17.420000] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[   17.428000] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +[   17.436000] cfg80211:   (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   17.444000] cfg80211:   (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +[   18.304000] b43-phy0: Broadcom 4318 WLAN found (core revision 9)
 +[   18.352000] b43-phy0: Found PHY: Analog 3, Type 2 (G), Revision 7
 +[   18.380000] Broadcom 43xx driver loaded [ Features: PNL ]
 +[   18.460000] Broadcom 43xx-legacy driver loaded [ Features: PLID ]
 +[   18.888000] PPP generic driver version 2.4.2
 +[   19.388000] ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
 +[   19.392000] Registered led device: b43-phy0::tx
 +[   19.392000] Registered led device: b43-phy0::rx
 +[   19.392000] Registered led device: b43-phy0::assoc
 +[   19.392000] Registered led device: b43-phy0::radio
 +[   19.420000] ip_tables: (C) 2000-2006 Netfilter Core Team
 +[   19.696000] NET: Registered protocol family 24
 +[   19.740000] nf_conntrack version 0.5.0 (457 buckets, 1828 max)
 +[   23.816000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
 +[   23.820000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
 +[   27.124000] b44 ssb0:0: eth0: powering down PHY
 +[   27.148000] b44 ssb0:0: eth0: Link is up at 100 Mbps, full duplex
 +[   27.152000] b44 ssb0:0: eth0: Flow control is off for TX and off for RX
 +[   27.184000] device eth0.0 entered promiscuous mode
 +[   27.188000] device eth0 entered promiscuous mode
 +[   27.200000] br-lan: port 1(eth0.0) entered forwarding state
 +[   27.204000] br-lan: port 1(eth0.0) entered forwarding state
 +[   29.208000] br-lan: port 1(eth0.0) entered forwarding state</nowiki>
 +</WRAP>\\
 +
 +==== V2 Backfire bootlog ====
 +<WRAP bootlog>
 +<nowiki>Decompressing..........done
 +
 +
 +CFE version 1.0.37 for BCM947XX (32bit,SP,LE)
 +Build Date: Mon Apr 16 14:41:05 CST 2007 (root@localhost.localdomain)
 +Copyright (C) 2000,2001,2002,2003 Broadcom Corporation.
 +
 +Initializing Arena
 +Initializing Devices.
 +Boot partition size = 131072(0x20000)
 +et0: Broadcom BCM47xx 10/100 Mbps Ethernet Controller 4.130.23.0
 +CPU type 0x29029: 240MHz
 +Total memory: 32768 KBytes
 +
 +Total memory used by CFE:  0x80400000 - 0x8049A790 (632720)
 +Initialized Data:          0x80430720 - 0x80432D10 (9712)
 +BSS Area:                  0x80432D10 - 0x80434790 (6784)
 +Local Heap:                0x80434790 - 0x80498790 (409600)
 +Stack Area:                0x80498790 - 0x8049A790 (8192)
 +Text (code) segment:       0x80400000 - 0x80430720 (198432)
 +Boot area (physical):      0x0049B000 - 0x004DB000
 +Relocation Factor:         I:00000000 - D:00000000
 +
 +Device eth0:  hwaddr 00-1F-XX-XX-XX-XX, ipaddr 192.168.1.1, mask 255.255.255.0
 +        gateway not set, nameserver not set
 +Null Rescue Flag.
 +Loader:raw Filesys:tftp Dev:eth0 File:: Options:(null)
 +Loading: TFTP Server.
 +Failed.
 +Could not load :: Timeout occured
 +Loader:raw Filesys:raw Dev:flash0.os File: Options:(null)
 +Loading: .. 4092 bytes read
 +Entry at 0x80001000
 +Closing network.
 +Starting program at 0x80001000
 +Linux version 2.6.32.27 (jow@nd-build-02.linux-appliance.net) (gcc version 4.3.3 (GCC) ) #5 Wed Dec 21 05:56:26 CET 2011
 +CPU revision is: 00029029 (Broadcom BCM3302)
 +ssb: chipcommon status is 0x0
 +ssb: Initializing MIPS core...
 +ssb: set_irq: core 0x0806, irq 4 => 4
 +ssb: set_irq: core 0x0816, irq 5 => 2
 +ssb: set_irq: core 0x0812, irq 2 => 5
 +ssb: after irq reconfiguration
 +ssb: core 0x0800, irq : 2(S)  3* 4  5  6  D  I
 +ssb: core 0x0806, irq : 2(S)  3  4* 5  6  D  I
 +ssb: core 0x0816, irq : 2(S)* 3  4  5  6  D  I
 +ssb: core 0x0819, irq : 2(S)  3  4  5  6* D  I
 +ssb: core 0x080f, irq : 2(S)  3  4  5  6  D  I*
 +ssb: core 0x0812, irq : 2(S)  3  4  5* 6  D  I
 +ssb: core 0x081c, irq : 2(S)  3  4  5  6  D  I*
 +ssb: Sonics Silicon Backplane found at address 0x18000000
 +Serial init done.
 +Determined physical RAM map:
 + memory: 02000000 @ 00000000 (usable)
 +Initrd not found or empty - disabling initrd
 +Zone PFN ranges:
 +  Normal   0x00000000 -> 0x00002000
 +Movable zone start PFN for each node
 +early_node_map[1] active PFN ranges
 +    0: 0x00000000 -> 0x00002000
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
 +Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
 +PID hash table entries: 128 (order: -3, 512 bytes)
 +Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
 +Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
 +Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
 +Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
 +Memory: 29496k/32768k available (2332k kernel code, 3272k reserved, 355k data, 136k init, 0k highmem)
 +Hierarchical RCU implementation.
 +NR_IRQS:128
 +console [ttyS0] enabled
 +Calibrating delay loop... 239.61 BogoMIPS (lpj=479232)
 +Mount-cache hash table entries: 512
 +NET: Registered protocol family 16
 +bio: create slab <bio-0> at 0
 +Switching to clocksource MIPS
 +NET: Registered protocol family 2
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP established hash table entries: 1024 (order: 1, 8192 bytes)
 +TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
 +TCP: Hash tables configured (established 1024 bind 1024)
 +TCP reno registered
 +NET: Registered protocol family 1
 +squashfs: version 4.0 (2009/01/31) Phillip Lougher
 +Registering mini_fo version $Id$
 +JFFS2 version 2.2. (NAND) (SUMMARY)  ?? 2001-2006 Red Hat, Inc.
 +msgmni has been set to 57
 +io scheduler noop registered
 +io scheduler deadline registered (default)
 +Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
 +serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
 +serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
 +serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
 +serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
 +flash init: 0x1c000000 0x02000000
 +Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
 + CFI mfr 0x000000c2
 + CFI id  0x000022cb
 + Amd/Fujitsu Extended Query Table at 0x0040
 +  Amd/Fujitsu Extended Query version 1.1.
 +number of CFI chips: 1
 +cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
 +Flash device: 0x800000 at 0x1fc00000
 +bootloader size: 131072
 +Creating 4 MTD partitions on "Physically mapped flash":
 +0x000000000000-0x000000020000 : "cfe"
 +0x000000020000-0x0000007f0000 : "linux"
 +0x0000000fb000-0x0000007f0000 : "rootfs"
 +mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
 +mtd: partition "rootfs" set to be root filesystem
 +mtd: partition "rootfs_data" created automatically, ofs=2E0000, len=510000
 +0x0000002e0000-0x0000007f0000 : "rootfs_data"
 +0x0000007f0000-0x000000800000 : "nvram"
 +b44.c:v2.0
 +eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:1f:xx:xx:xx:xx
 +BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
 +TCP westwood registered
 +NET: Registered protocol family 17
 +802.1Q VLAN Support v1.8 Ben Greear <@candelatech.com>
 +All bugs added by David S. Miller <@redhat.com>
 +VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
 +Freeing unused kernel memory: 136k freed
 +Please be patient, while OpenWrt loads ...
 +diag: Detected 'ASUS WL-500g Premium V2'
 +b44: eth0: Link is up at 100 Mbps, full duplex.
 +b44: eth0: Flow control is off for TX and off for RX.
 +roboswitch: Probing device eth0: found a 5325! It's a 5350.
 +- preinit -
 +Press the [f] key and hit [enter] to enter failsafe mode
 +- regular preinit -
 +switching to jffs2
 +mini_fo: using base directory: /
 +mini_fo: using storage directory: /overlay
 +- init -
 +b44: eth0: powering down PHY
 +
 +Please press Enter to activate this console. b44: eth0: Link is up at 100 Mbps, full duplex.
 +b44: eth0: Flow control is off for TX and off for RX.
 +device eth0.0 entered promiscuous mode
 +device eth0 entered promiscuous mode
 +br-lan: port 1(eth0.0) entering forwarding state
 +Compat-wireless backport release: compat-wireless-2011-11-08-1-g4ab9b62
 +Backport based on wireless-testing.git master-2011-11-15
 +cfg80211: Calling CRDA to update world regulatory domain
 +PPP generic driver version 2.4.2
 +NET: Registered protocol family 24
 +b43-phy0: Broadcom 5354 WLAN found (core revision 13)
 +Registered led device: b43-phy0::tx
 +Registered led device: b43-phy0::rx
 +Broadcom 43xx driver loaded [ Features: PL ]
 +Broadcom 43xx-legacy driver loaded [ Features: PLID ]
 +ip_tables: (C) 2000-2006 Netfilter Core Team
 +nf_conntrack version 0.5.0 (463 buckets, 1852 max)
 +CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
 +nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
 +sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
 +cfg80211: World regulatory domain updated:
 +cfg80211:     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
 +cfg80211:     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +cfg80211:     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +cfg80211:     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
 +cfg80211:     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +cfg80211:     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
 +xt_time: kernel timezone is -0000</nowiki>
 +</WRAP>\\
 +
 +===== External Links =====
 +==== Tutorials ====
 +  * [[http://wl500g.info/showthread.php?t=12962|RAM Upgrade]]
 +  * [[http://www.marcusbrutus.soho.on.net/blog/?p=67|Adding a Bluetooth PAN]] by Marcus Brown
 +  * [[http://sr.uz/index.php?p=223&more=1&c=1&tb=1&pb=1|Example configuration for the Atheros MiniPCI card on wl-500gP (translated from Russian)]]  and [[http://sr.uz/index.php?p=220&more=1&c=1&tb=1&pb=1|The original Russian text]]
 +  * [[http://josefsson.org/openwrt/wlan.html|Setting up WDS/PSK2 on two Asus WL-500gP]] by Simon Josefsson
 +  * [[http://josefsson.org/openwrt/dongle.html|Using Huawei E220 with Asus WL-500gP]] by Simon Josefsson
 +==== Product Info Pages ====
 +  * FCC ID: MSQWL500GP [[https://gullfoss2.fcc.gov/prod/oet/forms/blobs/retrieve.cgi?attachment_id=640814&native_or_pdf=pdf|FCC pictures]]
 +  * [[http://www.xbitlabs.com/articles/other/display/asus-wl500g-premium.html|Review of the 500gP (pictures starting on page 3)]]
 +  * [[oldwiki:hardwareacceleratedcrypto|HardwareAcceleratedCrypto]]
 +  * official ASUS website: [[http://usa.asus.com/Networks/Wireless_Routers/WL500g_Premium/|v1]], [[http://usa.asus.com/Networks/Wireless_Routers/WL500gP_V2/|v2]]
 +  * [[http://www.broadcom.com/products/Wireless-LAN/802.11-Wireless-LAN-Solutions/BCM94704|Broadcom BCM94704 Reference SoC]]
 +  * [[http://www.broadcom.com/products/BCM5325|Broadcom BCM5325 Ethernet Switch]]
 +  * [[http://www.spansion.com/products/S29GL064M.html|Spansion S29GL064M90 Flash Memory Module]]
 +  * [[http://www.hynix.com/datasheet/pdf/dram/HY5DU284(8,16)22ETP(Rev0.3).pdf|Hynix HY5DU281622ETP-K SDRAM Datasheet]]
 +  * [[http://www.via.com.tw/en/products/peripherals/usb/vt6212l/|VIA Vectro VT6212L USB 2.0 Host Controller]]
 +  * [[http://www.delta.com.tw/product/cp/telecom/networking/download/pdf/LF8258_and_more.pdf|Delta Electronics LF8731 Ethernet PHY Datasheet]]
 +  * [[http://www.delta.com.tw/product/cp/telecom/networking/download/pdf/LF8275%208504%208505%208508.pdf|Delta Electronics LF8505 Ethernet PHY Datasheet]]
 +
 +==== Forum Threads ====
 +  * [[http://wl500g.info/forumdisplay.php?f=61|Dedicated Forum]]
 +  * [[http://forum.openwrt.org/viewtopic.php?id=6090|Problems with WLAN encryption]]
 +  * [[http://forum.openwrt.org/viewtopic.php?id=6071|CPU Power]]
 +  * [[http://forum.openwrt.org/viewtopic.php?id=5688|OpenWRT compatibility information]]
 +  * [[http://forum.openwrt.org/viewtopic.php?id=6362|How-to configure WAN-interface]]
 +
 +===== Tags =====
 +{{tag>bcm47xx bcm53xx bcm4704 bcm5354 FastEthernet 1NIC 1WNIC 5Port hwVLAN USB 2USB 802.11bg integrated MiniPCI 1Ant DetachableAntenna 32RAM 8Flash MIPS}}
  • Last modified: 2021/04/07 15:56
  • by tmomas