Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| ru:toh:asus:asus_wl-330ge [2018/02/17 19:11] – ↷ Links adapted because of a move operation | ru:toh:asus:asus_wl-330ge [2018/03/04 10:31] – bobafetthotmail | ||
|---|---|---|---|
| Line 47: | Line 47: | ||
| ===== Installation ===== | ===== Installation ===== | ||
| - | - → [[doc:howto: | + | - → [[:downloads]] |
| - | - → [[docs:user-guide: | + | - → [[docs: |
| - → [[about/ | - → [[about/ | ||
| Line 60: | Line 60: | ||
| ==== Flash Layout ==== | ==== Flash Layout ==== | ||
| - | Please check out the article [[doc:techref:Flash.Layout]]. It contains an example and a couple of explanations. | + | Please check out the article [[docs:techref:flash.layout]]. It contains an example and a couple of explanations. |
| ==== OEM easy installation ==== | ==== OEM easy installation ==== | ||
| Line 76: | Line 76: | ||
| ==== OEM installation using the TFTP method ==== | ==== OEM installation using the TFTP method ==== | ||
| - | -> [[docs:user-guide: | + | -> [[docs: |
| === Specific values you need === | === Specific values you need === | ||
| Line 88: | Line 88: | ||
| ==== Upgrading OpenWrt ==== | ==== Upgrading OpenWrt ==== | ||
| - | -> [[docs:user-guide: | + | -> [[docs: |
| If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. | If you have already installed OpenWrt and like to reflash for e.g. upgrading to a new OpenWrt version you can upgrade using the mtd command line tool. It is important that you put the firmware image into the ramdisk (/tmp) before you start flashing. | ||
| Line 118: | Line 118: | ||
| ===== Basic configuration ===== | ===== Basic configuration ===== | ||
| - | -> [[doc:howto:basic.config|Basic configuration]] After flashing, proceed with this.\\ | + | -> [[docs:guide-quick-start:checks_and_troubleshooting|Basic configuration]] After flashing, proceed with this.\\ |
| Set up your Internet connection, configure wireless, configure USB port, etc. | Set up your Internet connection, configure wireless, configure USB port, etc. | ||
| Line 142: | Line 142: | ||
| ==== Failsafe mode ==== | ==== Failsafe mode ==== | ||
| - | -> [[doc:howto:generic.failsafe]] | + | -> [[docs:guide-user:troubleshooting: |
| ==== Buttons ==== | ==== Buttons ==== | ||
| - | -> [[docs:user-guide: | + | -> [[docs: |
| The Linksys WRT54GL has two buttons. They are Reset and Secure Easy Setup. Here, we merely name the buttons, so we can use them in the above Howto: | The Linksys WRT54GL has two buttons. They are Reset and Secure Easy Setup. Here, we merely name the buttons, so we can use them in the above Howto: | ||
| Line 182: | Line 182: | ||
| ==== Serial ==== | ==== Serial ==== | ||
| - | -> [[doc: | + | -> [[docs: |
| How to connect to the Serial Port of this specific device: | How to connect to the Serial Port of this specific device: | ||
| Line 189: | Line 189: | ||
| ==== JTAG ==== | ==== JTAG ==== | ||
| - | -> [[doc: | + | -> [[docs: |
| How to connect to the JTAG Port of this specific device: | How to connect to the JTAG Port of this specific device: | ||
| Line 197: | Line 197: | ||
| ===== Debricking ===== | ===== Debricking ===== | ||
| - | -> [[docs:user-guide: | + | -> [[docs: |
| ===== Bootloader Mods ===== | ===== Bootloader Mods ===== | ||
| - | - you could read about [[doc: | + | - you could read about [[docs: |
| ===== Hardware mods ===== | ===== Hardware mods ===== | ||
| - | - as a beginner, you really should inform yourself about [[doc: | + | - as a beginner, you really should inform yourself about [[docs: |
| ==== 128MiB RAM Mod ==== | ==== 128MiB RAM Mod ==== | ||