OpenWrt 24.10.5 - Service Release - 19. December 2025
_______ ________ __
| |.-----.-----.-----.| | | |.----.| |_
| - || _ | -__| || | | || _|| _|
|_______|| __|_____|__|__||________||__| |____|
|__| W I R E L E S S F R E E D O M
-----------------------------------------------------
OpenWrt 24.10.5, r29087-d9c5716d1d
-----------------------------------------------------
The OpenWrt community is proud to announce the newest stable release of the OpenWrt 24.10 stable series.
Download firmware images via the Firmware Selector or directly from our download servers:
An upgrade from OpenWrt 23.05 to OpenWrt 24.10 is supported in many cases with the help of the sysupgrade utility which will also attempt to preserve the configuration. A configuration backup is advised nonetheless when upgrading to OpenWrt 24.10. (see “Upgrading” below).
About OpenWrt
The OpenWrt Project is a Linux operating system targeting embedded devices. It is a complete replacement for the vendor-supplied firmware of a wide range of wireless routers and non-network devices. See the Table of Hardware for supported devices. For more information about OpenWrt project organization, see the About OpenWrt pages.
Announcements about new releases and security fixes
Do you want to be informed about important changes such as new releases and security fixes?
We have a new mailing list for this, as well as RSS options: see Important changes and announcements.
Main changes between OpenWrt 24.10.4 and OpenWrt 24.10.5
Only the main changes are listed below. See changelog-24.10.5 for the full changelog.
Security fixes
Device support
- Added new devices:
- mediatek: ASUS TUF-AX4200Q
- mediatek: Cudy WR3000P v1
- mediatek: ipTIME AX7800M-6E
- mediatek: Konka KOMI A31
- mediatek: Totolink X6000R
- mediatek: WAVLINK WL-WN536AX6 Rev a
- ramips: Cudy AP1300 Outdoor v1
- ramips: Cudy C200P
- ramips: Cudy R700
- ramips: Cudy RE1200 Outdoor v1
- ramips: Hongdian H8850 v20
- rockchip: LinkEase EasePi R1
- rockchip: Lunzn FastRhino R66S
- airoha: Many improvements
- ath79: TP-Link Archer C60 v2: fix 5GHz Wifi
- bmips: Sagem @ST3864OP: fix LEDs
- ipq4019: AVM FritzBox 7530: fix RX frame length on DSL interface
- ipq806x: migrate wifi configuration when downgrading from kernel 6.12
- mediatek: Cudy AP3000 v1: fix IPv4 address missing on interface in failsafe mode
- mediatek: Cudy WR3000H: fix Ethernet port order
- mediatek: Zbtlink ZBT Z8102AX V2: fix ubi size
- mpc85xx: p1010: Sophos RED 15w : Fix NAND partitions
- mpc85xx: p1010: Watchguard Firebox T10: fix boot
- mvebu: GL.iNet GL-MV1000: fix sdhci1 controller
- ramips: Improve eMMC and SD Card support
Various fixes and improvements
- ath11k: fix transmit queue flushing
- dropbear: backport security fixes
- dropbear: enable configurable port forwarding options
- imagebuilder: fix image generation for some devices
- kernel: add support for ESMT F50L1G41LC flash chip (found on recent Cudy boards)
- kernel: add support for Fudan Micro FM25S01BI3 flash chip
- mwl8k: improve stability of AP mode
- odhcpd: fix memory leaks
- ppp: add reqprefix, norelease and ac_mac options
Core components update
- Linux kernel: update from 6.6.110 to 6.6.119
- mac80211: update from 6.12.52 to 6.12.61
- mt76: update from 2025-09-15 to 2025-11-06
- wireless-regdb: update from 2025.07.10 to 2025.10.07
Upgrading to 24.10
Sysupgrade can be used to upgrade a device from 23.05 to 24.10, and configuration will be preserved in most cases. For for upgrades inside the OpenWrt 24.10 stable series for example from a OpenWrt 24.10 release candidate Attended Sysupgrade is supported in addition which allows preserving the installed packages too.
Sysupgrade from 22.03 to 24.10 is not officially supported.
There is no configuration migration path for users of the ipq806x target for Qualcomm Atheros IPQ806X SoCs because it switched to DSA. You have to upgrade without saving the configuration.
Image version mismatch. image 1.1 device 1.0 Please wipe config during upgrade (force required) or reinstall. Config cannot be migrated from swconfig to DSA Image check failed
User of the Linksys E8450 aka. Belkin RT3200 running OpenWrt 23.05 or earlier will need to run installer version v1.1.3 or later in order to reorganize the UBI layout for the 24.10 release. A detailed description is in the OpenWrt wiki. Updating without using the installer will break the device. Sysupgrade will show a warning before doing an incompatible upgrade.
Users of the Xiaomi AX3200 aka. Redmi AX6S running OpenWrt 23.05 or earlier have to follow a special upgrade procedure described in the wiki. This will increase the flash memory available for OpenWrt. Updating without following the guide in the wiki break the device. Sysupgrade will show a warning before doing an incompatible upgrade.
Users of Zyxel GS1900 series switches running OpenWrt 23.05 or earlier have to perform a new factory install with the initramfs image due to a changed partition layout. Sysupgrade will show a warning before doing an incompatible upgrade and is not possible. After upgrading, the config file /etc/config/system should not be restored from a backup, as this will overwrite the new compat_version value.
Known issues
- LEDs for Airoha AN8855 are not yet supported. Devices like the Xiaomi AX3000T with an Airoha switch will have their switch LEDs powered off. This issue will be addressed in an upcoming OpenWrt SNAPSHOT and the OpenWrt 24.10 minor release.
- 5GHz WiFi is non-functional on certain devices with ath10k chipsets. Affected models include the Phicomm K2T, TP-Link Archer C60 v3 and possibly others. For details, see issue #14541.
Final notes
As always, a big thank you goes to all our active package maintainers, testers, documenters, and supporters.
Have fun!
The OpenWrt Community