ZyXEL VMG8825-T50

The ZyXEL VMG8825-T50 is a cheap but modern modem/router that is provided by ISP's. It supports ADSL, and has an ethernet WAN port. The device has built in Wifi 2.4/5Ghz with support up to Wifi AC. It has 4 ethernet port for the LAN network, one USB 2.0 port and one usb 3.0 port. The firmware on it is fairly restrictive, but not as bad as some other modems. Appears to run some pretty old software.

VMG8825-T50

Not supported.

CPU Ram Flash Network WLAN USB Serial JTag
Econet EN7516 @ 900 MHz 512 MiB 2Gb 1+4x 10/100/1000 bgn/ac 1x 2.0, 1x 3.0 Yes no
Architecture MIPS
Vendor MediaTek/EcoNet
Bootloader ZyXEL zloader v1.4.4
System-On-Chip EcoNet EN7516 - MIPS32® 1004K™ V4.12
CPU/Speed Dual core 2×900 MHz
Flash-Chip Winbond W25M02GV
Flash size 2Gb
RAM 512MB
Wireless MT7615 Wi-Fi 5 (b/g/n/ac)
Ethernet 1x WAN, 4x LAN (10/100/1000Mbit/s w/ vlan support)
Switch Built in to SoC
USB 1x 2.0, 1x 3.0
Serial Yes
JTAG No

You only need to remove to Philips screws at the back of the unit. After that, you will be able to separate the back and front plastic pieces of the device. The parts are still hold together with clips, if you insert a small plastic part in the gap between the two pieces you should be able to pry it open fairly easily.

I've used this USB to serial adapter to connect to the device: https://www.kiwi-electronics.nl/usb-to-ttl-serial-kabel?lang=en

Shows what pins to connect to for serial console Shows what pins to connect to for serial console

Serial connection parameters
for ZyXEL VMG8825-T50
115200, 8N1

BGA IC Xtal:1 DDR3 init. DRAMC init done. Calculate size. DRAM size=512MB Set new TRFC. ddr-1333 7516DRAMC V1.0 (0) Press 'x' or 'b' key in 1 secs to enter or skip bootloader upgrade. EN751627 at Fri May 15 15:20:05 CST 2020 version 1.1 free bootbase Set SPI Clock to 50 Mhz spi_nand_probe: mfr_id=0xef, dev_id=0xab Using Flash ECC. Detected SPI NAND Flash : _SPI_NAND_DEVICE_ID_W25M02G, Flash Size=0x10000000 bmt pool size: 163 BMT & BBT Init Success ZyXEL zloader v1.4.4 (05/15/2020 - 15:20:04) Multiboot client version: 2.4 Not found TC Phy Not found TC Phy Not found TC Phy Not found TC Phy Not found TC Phy GE Rext AnaCal Done! (4)(0x1c) Hit any key to stop autoboot: 0 main tclinux.bin have ZYXEL trx header! main tclinux.bin Start to decrypt RSA! ==> boot flag = 0 from main Decompress to 80002000 free_mem_ptr=80950000 free_mem_ptr_end=807B0000 Uncompressing [LZMA] ... done. Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 3.18.21 (howard@TWPCZT02587-03) (gcc version 4.6.3 (OpenWrt GCC 4.6.3 unknown) ) #2 SMP Fri May 15 16:39:01 CST 2020 memsize:432MB EcoNet EN751627 SOC prom init bootconsole [early0] enabled CPU0 revision is: 0001992f (MIPS 1004Kc) Determined physical RAM map: memory: 1affe000 @ 00002000 (usable) Wasting 64 bytes for tracking 2 unused pages Zone ranges: Normal [mem 0x00002000-0x1affffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x00002000-0x1affffff] Initmem setup node 0 [mem 0x00002000-0x1affffff] Detected 3 available secondary CPU(s) Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. PERCPU: Embedded 9 pages/cpu @81364000 s6272 r8192 d22400 u36864 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 109726 Kernel command line: log_buf_len individual max cpu contribution: 4096 bytes log_buf_len total cpu_extra contributions: 12288 bytes log_buf_len min size: 16384 bytes log_buf_len: 32768 bytes early log buf free: 14280(87%) PID hash table entries: 2048 (order: 1, 8192 bytes) Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Writing ErrCtl register=0007c95f Readback ErrCtl register=0007c95f nmi base is 813fc200 Memory: 431420K/442360K available (4925K kernel code, 216K rwdata, 936K rodata, 240K init, 541K bss, 10940K reserved) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 Hierarchical RCU implementation. NR_IRQS:64 tc3162_time_init: Init bus timeout and watchdog CPU frequency 900.00 MHz plat_time_init: Entered, mips_timer_ack ptr is [80007378] Using 200.000 MHz high precision timer. r4k_clockevent_init: setup_irq OK, irq is [52] console [ttyS0] enabled console [ttyS0] enabled bootconsole [early0] disabled bootconsole [early0] disabled Calibrating delay loop... 589.00 BogoMIPS (lpj=2945024) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys net_cls Initializing cgroup subsys blkio Initializing cgroup subsys debug 34K sync es set to 0. Config7: 0x80090500 launch: starting cpu1 launch: cpu1 gone! Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. CPU1 revision is: 0001992f (MIPS 1004Kc) Synchronize counters for CPU 1: done. launch: starting cpu2 launch: cpu2 gone! Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. CPU2 revision is: 0001992f (MIPS 1004Kc) Synchronize counters for CPU 2: done. launch: starting cpu3 launch: cpu3 gone! Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. CPU3 revision is: 0001992f (MIPS 1004Kc) Synchronize counters for CPU 3: done. Brought up 4 CPUs devtmpfs: initialized NET: Registered protocol family 16 PCIe 7516 PHY init PCIe driver version: 751627.1.20170815 EN751627 pcie_init check pcie link up status: isRC0_LINKUP=1 isRC1_LINKUP=1 registering PCI controller with io_map_base unset Initializing Ecnt Event Netlink Socket Initializing Econet Event Netlink Socket nl_sk = 9ad58800 usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] pci_bus 0000:00: root bus resource [io 0x1f600000-0x1f61ffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff] pci 0000:00:01.0: BAR 8: assigned [mem 0x20100000-0x201fffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff] pci 0000:02:00.0: BAR 0: assigned [mem 0x20100000-0x201fffff 64bit] pci 0000:00:01.0: PCI bridge to [bus 02] pci 0000:00:01.0: bridge window [mem 0x20100000-0x201fffff] NET: Registered protocol family 8 NET: Registered protocol family 20 Switched to clocksource MIPS NET: Registered protocol family 2 TCP established hash table entries: 4096 (order: 2, 16384 bytes) TCP bind hash table entries: 4096 (order: 3, 32768 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 mt7512_pcie_fixup: 0x1438 = 20000014 mt7512_pcie_rc0_retrain: 80 = 01408c12 80 = 01608c12 RC0 Link Traing Result: 10120008 mt7512_pcie_fixup: 0x3438 = 20100014 mt7512_pcie_rc1_retrain: 80 = 01408c12 80 = 01608c12 RC1 Link Traing Result: 10120008 TC3162 hardware watchdog module loaded. USB overcurrent protection. futex hash table entries: 1024 (order: 4, 65536 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher ntfs: driver 2.1.31 [Flags: R/W DEBUG]. msgmni has been set to 842 io scheduler noop registered (default) ttyS0 at I/O 0xbfbf0003 (irq = 5, base_baud = 7200) is a TC3162 ECNT ring buffer init success Init UART2 and UART3, still need to trun on for using. ttyS20 at I/O 0xbfbf0300 (irq = 4, base_baud = 7200) is a TC3162 ttyS30 at I/O 0xbfbe1000 (irq = 3, base_baud = 7200) is a TC3162 brd: module loaded SPI Flash Init Start Found no SPI flash device IS_SPIFLASH=0x0, IS_NANDFLASH=0x2, (0xBFA10114)=0x6) Set SPI Clock to 50 Mhz spi_nand_probe: mfr_id=0xef, dev_id=0xab Using Flash ECC. Detected SPI NAND Flash : _SPI_NAND_DEVICE_ID_W25M02G, Flash Size=0x10000000 spi nand flash tc3162: flash device 0x01000000 at 0x1c000000 EN7512 mtd init: spi nand probe enter [spi_nand_setup] : Enter nand: device found, Manufacturer ID: 0xef, Chip ID: 0xab nand: Unknown _SPI_NAND_DEVICE_ID_W25M02G nand: 256MiB, SLC, page size: 2048, OOB size: 64 nand_scan_ident ok [spi_nand_setup]: chip size = 0x10000000, erase_shift=0x11 bmt pool size: 163 BMT & BBT Init Success parsing <0[bootloader],0[romfile],56M[tclinux],-[tclinux_slave],1M[wwan],4M[data],1M[rom-d],118M[misc]> partition 11: name <misc>, offset ffffffff, size 7600000, mask flags 0 partition 10: name <rom-d>, offset ffffffff, size 100000, mask flags 0 partition 9: name <data>, offset ffffffff, size 400000, mask flags 0 partition 8: name <wwan>, offset ffffffff, size 100000, mask flags 0 partition 7: name <tclinux_slave>, offset ffffffff, size ffffffff, mask flags 0 partition 4: name <tclinux>, offset ffffffff, size 3800000, mask flags 0 partition 1: name <romfile>, offset ffffffff, size fffffffe, mask flags 0 partition 0: name <bootloader>, offset ffffffff, size fffffffe, mask flags 0 Creating 13 MTD partitions on "EN7512-SPI_NAND": 0x000000000000-0x000000040000 : "bootloader" 0x000000040000-0x000000080000 : "romfile" 0x000000080000-0x00000028ccdd : "kernel" mtd: partition "kernel" doesn't end on an erase block -- force read-only 0x00000028ccdd-0x0000016ccce1 : "rootfs" mtd: partition "rootfs" doesn't start on an erase block boundary -- force read-only 0x000000080000-0x000003880000 : "tclinux" 0x000003880000-0x000003a8cc01 : "kernel_slave" mtd: partition "kernel_slave" doesn't end on an erase block -- force read-only 0x000003a8cc01-0x000004e0cc05 : "rootfs_slave" mtd: partition "rootfs_slave" doesn't start on an erase block boundary -- force read-only 0x000003880000-0x000006ee0000 : "tclinux_slave" 0x000006ee0000-0x000006fe0000 : "wwan" 0x000006fe0000-0x0000073e0000 : "data" 0x0000073e0000-0x0000074e0000 : "rom-d" 0x0000074e0000-0x00000eae0000 : "misc" 0x00000eae0000-0x00000eba0000 : "reservearea" rootfs PPP generic driver version 2.4.2 PPP BSD Compression module registered PPP Deflate Compression module registered NET: Registered protocol family 24 usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver usbserial usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver cypress_m8 usbserial: USB Serial support registered for DeLorme Earthmate USB usbserial: USB Serial support registered for HID->COM RS232 Adapter usbserial: USB Serial support registered for Nokia CA-42 V2 Adapter usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device hidraw: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver GACT probability NOT on u32 classifier Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (6740 buckets, 26960 max) ctnetlink v0.93: registering with nfnetlink. nf_conntrack_rtsp v0.7 loading nf_nat_rtsp v0.7 loading nf_tables: (c) 2007-2009 Patrick McHardy <kaber@trash.net> nf_tables_compat: (c) 2012 Pablo Neira Ayuso <pablo@netfilter.org> xt_time: kernel timezone is -0000 ip_tables: (C) 2000-2006 Netfilter Core Team ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully TCP: cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. 8021q: 802.1Q VLAN Support v1.8 tc3162ser_startup VFS: Mounted root (squashfs filesystem) readonly on device 31:3. Freeing unused kernel memory: 240K (805f4000 - 80630000) mknod: /dev/ppp: File exists mknod: /dev/ptmx: File exists mknod: /dev/ptyp0: File exists mknod: /dev/ptyp1: File exists mknod: /dev/ptyp2: File exists mknod: /dev/ttyp0: File exists mknod: /dev/ttyp1: File exists mknod: /dev/ttyp2: File exists mknod: /dev/watchdog: File exists mknod: /dev/ttyS20: File exists mknod: /dev/ttyS30: File exists mknod: /dev/hwnat0: File exists mknod: /dev/acl0: File exists mknod: /dev/ac0: File exists mknod: /dev/mtr0: File exists **************prepare var***************** busybox init and set aff init started: BusyBox v1.20.1 (2020-05-15 14:51:49 CST) chmod: /userfs/profile.cfg: Read-only file system TCSUPPORT_IPV6 /dev created at preinit Reading MT7615 2.4G EEPROM from flash reservearea mtd[readflash]:device=reservearea tclen=1024 tcoffset=0 Unlocking reservearea ... Reading from reservearea to /etc/RT30xxEEPROM.bin ... Reading MT7615 5G EEPROM from flash reservearea mtd[readflash]:device=reservearea tclen=1024 tcoffset=131072 Unlocking reservearea ... Reading from reservearea to /etc/Wireless/RT2860AP_AC/RT30xxEEPROM.bin ... Reading MT7615 2.4G CALDATA from flash reservearea mtd[readflash]:device=reservearea tclen=36864 tcoffset=4096 Unlocking reservearea ... Reading from reservearea to /etc/CALDATA_default.bin ... Reading MT7615 5G CALDATA from flash reservearea mtd[readflash]:device=reservearea tclen=36864 tcoffset=135168 Unlocking reservearea ... Reading from reservearea to /etc/Wireless/RT2860AP_AC/CALDATA_default.bin ... insmod ETH_LAN driver Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful Exec. Successful install dmt for mt7510 TCSUPPORT_WLAN TCSUPPORT_WLAN_MT7615 TCSUPPORT_MAP_FILTER ifconfig: SIOCGIFFLAGS: No such device **************lan port init***************** four ports device eth0 is not a slave of br0 taskset: invalid number '0x8' date: invalid date '010100002012' /etc/init.d/rcS: line 1457: /userfs/bin/wpa_supplicant: not found CO-FW parameter.......... PRODUCT_NAME_VOIP_CHECK=1 MTK DSP support voip_loader start START CHECK ZARLIN ZSI [SLIC] le9642 Loading le9642,slic num:1 Loading common init mod-ksocket init mod-acodec init mod-foip3 voip loader end taskset: invalid number '0x8' taskset: invalid number '0x8' taskset: invalid number '0x8' taskset: invalid number '0x8' taskset: invalid number '0x8' wan ether support TCSUPPORT_WLAN_SW_RPS VDSP_GetInstance:278 /proc/net/skbmgr_4k_limit ??? Jan 1 00:00:28 crond[433]: crond: crond (busybox 1.20.1) started, log level 8 START disable Lan and Wan... ln: /dev/log: File exists 1970-01-01 00:00:29 dnsmasq<454>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 23 bind server socket 3 on /var/lib/.sock/zcfg_sockaddr23 successfully dnsmasq: unknown user or group: root 1970-01-01 00:00:29 zcmd<459>, zcmd.c:6172, main(), INFO: Start ZCMD daemon 1970-01-01 00:00:29 zcmd<460>, uitimer.c:95, UITimerProc(), INFO: thread starts killall: zywifid_run.sh: no process killed zcfg_schema.bin killall: zywifid: no process killed 1970-01-01 00:00:30 zywifid<474>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 40 bind server socket 3 on /var/lib/.sock/zcfg_sockaddr40 successfully *reg=0000001c value:68106810 Load NComm TMS Module. zywifid> [ALERT] wifi_module_init:1082: load libzywl_001_ecn.so .......... Find MTD Device /dev/mtd1 with name romfile. mtd.oobsize 64 mtd.writesize 2048 romfile type ffff romfile size 4294967295 romfile crc 65535 zywifid> [ALERT] main:1211: Check and fix Wifi MAC address...... Please press Enter to activate this console. rm: can't remove '/tmp/wifiScanTime*': No such file or directory MAX Number of Interface Stack is 254 Enter zcmdTr98MapTableInit zcmdTr98ParmAttrNodeBuild: zcmdTr98ParmAttrNodeBuild: obj 67176 3,1,0,0,0,0 nSetParmAttr 1 setParmAttrNodeLst Add, n=1 zcmdTr98ParmAttrNodeBuild: obj 67176 4,1,0,0,0,0 nSetParmAttr 1 setParmAttrNodeLst Add, n=2 zcmdTr98ParmAttrNodeBuild: obj 67176 5,1,0,0,0,0 nSetParmAttr 1 setParmAttrNodeLst Add, n=3 zcmdTr98ParmAttrNodeBuild: obj 67176 6,1,0,0,0,0 nSetParmAttr 1 setParmAttrNodeLst Add, n=4 zcmdTr98ParmAttrNodeBuild: obj 67176 7,1,0,0,0,0 nSetParmAttr 1 setParmAttrNodeLst Add, n=5 zcmdTr98ParmAttrNodeBuild: obj 67176 8,1,0,0,0,0 nSetParmAttr 1 setParmAttrNodeLst Add, n=6 zcmdTr98ParmAttrNodeBuild: obj 67176 9,1,0,0,0,0 nSetParmAttr 1 setParmAttrNodeLst Add, n=7 zcmdTr98ParmAttrNodeBuild: obj 67176 10,1,0,0,0,0 nSetParmAttr 1 setParmAttrNodeLst Add, n=8 zcmdTr98ParmAttrNodeBuild: obj 67176 11,1,0,0,0,0 nSetParmAttr 1 setParmAttrNodeLst Add, n=9 zcmdTr98ParmAttrNodeBuild: obj 64788 1,0,0,0,0,0 nSetParmAttr 1 setParmAttrNodeLst Add, n=10 zcmdTr98ParmAttrNodeBuild: obj 14568 0,0,0,0,0,0 nSetParmAttr 2 setParmAttrNodeLst Add, n=11 zcmdTr98ParmAttrNodeBuild: obj 16920 0,0,0,0,0,0 nSetParmAttr 1 setParmAttrNodeLst Add, n=12 zcmdTr98ParmAttrNodeBuild: obj 112704 0,0,0,0,0,0 nSetParmAttr 2 setParmAttrNodeLst Add, n=13 zcmdTr98ParmAttrNodeBuild: obj 87144 1,0,0,0,0,0 nSetParmAttr 3 setParmAttrNodeLst Add, n=14 mainDhcpPoolInfo[0]= 1 [1 0] mainDhcpPoolInfo[1]= 0 [0 0] mainDhcpPoolInfo[2]= 0 [0 0] mainDhcpPoolInfo[3]= 0 [0 0] mainDhcpPoolInfo[4]= 0 [0 0] mainDhcpPoolInfo[5]= 0 [0 0] mainDhcpPoolInfo[6]= 0 [0 0] mainDhcpPoolInfo[7]= 0 [0 0] mainDhcpPoolInfo[8]= 0 [0 0] mainDhcpPoolInfo[9]= 0 [0 0] mainDhcpPoolInfo[10]= 0 [0 0] mainDhcpPoolInfo[11]= 0 [0 0] mainDhcpPoolInfo[12]= 0 [0 0] mainDhcpPoolInfo[13]= 0 [0 0] mainDhcpPoolInfo[14]= 0 [0 0] mainDhcpPoolInfo[15]= 0 [0 0] zcmdTr98MapTableInit End 1970-01-01 00:00:31 zcmd<459>, zcmd.c:6279, main(), INFO: tr98 map table inited zcmdReleaseTr98ObjParamMapping: no this object mapping zcmdReleaseTr98ObjParamMapping: object 86172 has mapping object zcmdReleaseTr98ObjParamMapping: object index attr zcmdReleaseTr98ObjParamMapping: object index 1 zcmdReleaseTr98ObjParamMapping: Release object 86172 mapping with data zcmdTr98MappingGrpQry: obj 86172 1,0,0,0,0,0 queried group 0 zcmdTr98MtRecognizeRDMappingOnRelease: objnum 86172, List obj 86172 zcmdTr98MappingGrpQry: obj 87144 1,0,0,0,0,0 queried group 0 zcmdTr98MtRecognizeRDMappingOnRelease: objnum 87144, List obj 87144 setParmAttrNodeLst Delete, n=13 =====zcmdTr98MtObjDelete=====seqnum=181 =====zcmdTr181MtObjDelete=====oid=87144 =====zcmdTr98MtObjDelete=====seqnum=180 =====zcmdTr181MtObjDelete=====oid=86172 1970-01-01 00:00:31 zcmd<459>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 1 bind server socket 4 on /var/lib/.sock/zcfg_sockaddr1 successfully 1970-01-01 00:00:31 zcmd<501>, zcmd_config_apply.c:1557, zcmdModuleConfigHandleTask(), INFO: thread starts 1970-01-01 00:00:31 zcmd<501>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 69 bind server socket 5 on /var/lib/.sock/zcfg_sockaddr69 successfully 1970-01-01 00:00:31 zcmd<500>, zcmd_config_apply.c:1639, zcmdConfigApplyTask(), INFO: thread starts 1970-01-01 00:00:31 zcmd<500>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 67 bind server socket 6 on /var/lib/.sock/zcfg_sockaddr67 successfully /bin/sh: dsldiagd: not found 1970-01-01 00:00:31 esmd<511>, esmd.c:2126, main(), INFO: ESMD Start ESMD msg server init... 1970-01-01 00:00:31 esmd<511>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 2 bind server socket 0 on /var/lib/.sock/zcfg_sockaddr2 successfully [ESMD] Initial kernel monitor ... kernelFd=7 1970-01-01 00:00:31 zcmd<519>, zcmd.c:5637, zcmdActiveZtr69(), INFO: thread starts Find MTD Device /dev/mtd8 with name wwan. mtd.oobsize 64 mtd.writesize 2048 FW_WATCHER Start Notice: zyUtilUpdateWWANPackage, No WWAN Package in Flash! wwanpackage info: revision is 1.18 1970-01-01 00:00:31 esmd<526>, esmd.c:1992, timer_thread(), INFO: thread starts zyUtilTcpSvrInit 1970-01-01 00:00:31 esmd<525>, esmd.c:1611, _esmd_thread(), INFO: ESMD ground thread starts 1970-01-01 00:00:31 esmd<525>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 66 bind server socket 9 on /var/lib/.sock/zcfg_sockaddr66 successfully 1970-01-01 00:00:31 esmd<524>, esmd.c:1603, _esmd_thread(), INFO: ESMD usr config thread starts zcmdBeInit(): DL opening... Initial begui_customization.... Initial bedevice.... Chain MACFILTER already exists. devObj->DeviceSummary = InternetGatewayDevice:1.4[](Baseline:1,EthernetLAN:2,WiFiLAN:1,ADSLWAN:1,ADSL2WAN:1,VDSL2WAN:1,PTMWAN:1,EthernetWAN:1,QoS:1,Time:1,IPPing:1),VoiceService:1[](Endpoint:1,SIPEndpoint:1,TAEndpoint:1) Initial bedsl.... sh: you need to specify whom to kill Initial beatmlink.... Initial beptmlink.... Jan 1 00:00:33 crond[637]: crond: crond (busybox 1.20.1) started, log level 8 Initial belog.... killall: tty_log_echo: no process killed killall: mailsend: no process killed Set interval time = 60 second killall: syslog-ng: no process killed Error resolving user; user='root' Initial besysinfo.... Initial beaccount.... mkdir: can't create directory '/var/tmp': File exists chmod: /data/zcfg_predef.json: No such file or directory chmod: /data/zcfg_predef.json: No such file or directory Initial bedevinfo.... 1970-01-01 00:00:35 zcmd<518>, zcfg_msg.c:419, _msg_send(), ERROR: fail to sendto /var/lib/.sock/zcfg_sockaddr9, errno = 2(No such file or directory), srcEid = 1, dstEid = 9, type = 273 without reply, oid = 0 1970-01-01 00:00:35 zcmd<518>, zcfg_msg.c:822, zcfg_msg_sendAndGetReply(), ERROR: fail to send message. ret = -5 Initial beethlink.... Initial beethintf.... auto, Auto-negotiation enabled. No common media type was autonegotiated! This is extremely unusual and typically indicates a configuration error. Perhaps the advertised capability set was intentionally limited. Link is down auto, Auto-negotiation enabled. No common media type was autonegotiated! This is extremely unusual and typically indicates a configuration error. Perhaps the advertised capability set was intentionally limited. Link is down auto, Auto-negotiation enabled. No common media type was autonegotiated! This is extremely unusual and typically indicates a configuration error. Perhaps the advertised capability set was intentionally limited. Link is down auto, Auto-negotiation enabled. No common media type was autonegotiated! This is extremely unusual and typically indicates a configuration error. Perhaps the advertised capability set was intentionally limited. Link is down Initial bewifi_radio.... Initial bewifi_ssid.... Initial bewifi_ap.... Initial bebridging.... Initial bebridgingbr.... Initial bebridgePort.... device ra0 is not a slave of br0 interface ra1 does not exist! device rai0 is not a slave of br0 interface rai1 does not exist! interface rai3 does not exist! Initial bebridgeFilter.... Initial bewifi.... Initial beipiface.... zywifid:Config> [ERROR] zyWifiUpdateLanInfo:404: No wifi interface on module(ECN). /bin/sh: zy1905App: not found zcmdTr98SyncTr98WANConnectNum: obj 65676 seqnum 204 zcmdTr98SyncTr98WANConnectNum: obj 65676 seqnum 204 zcmdTr98SyncTr98WANConnectNum: obj 65676 seqnum 204 zcmdTr98SyncTr98WANConnectNum: obj 65676 seqnum 204 zcmdTr98SyncTr98WANConnectNum: obj 65676 seqnum 204 zcmdTr98SyncTr98WANConnectNum: obj 65676 seqnum 204 zcmdTr98SyncTr98WANConnectNum: obj 65676 seqnum 204 zcmdTr98SyncTr98WANConnectNum: obj 65676 seqnum 204 zcmdTr98SyncTr98WANConnectNum: obj 65676 seqnum 204 zcfgBeWanInitIntfMark : Enter zcfgBeWanInitIntfMark: Init IfMark Done !! Initial benatIntf.... modprobe: module nf_nat_ftp not found in modules.dep modprobe: module nf_conntrack_ftp not found in modules.dep modprobe: module nf_nat_ftp not found in modules.dep ftp switch turn on sip switch turn on modprobe: module nf_conntrack_rtsp not found in modules.dep rtsp switch turn on pptp switch turn on Initial bev4addr.... Initial bev6addr.... Initial bev6prefix.... Initial beusbhost.... Initial beusbintf.... Initial beusbport.... Initial berouter.... Initial berainfo.... Initial bedhcp4_server.... Initial bedhcp4_serverpool.... Initial bedhcp4_serverpool_staticaddr.... Initial bedhcp4_serverpool_option.... Initial bedhcp4_serversubnet.... restart DNSMASQ... killall: dnsmasq: no process killed 1970-01-01 00:01:11 dnsmasq<1222>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 23 bind server socket 9 on /var/lib/.sock/zcfg_sockaddr23 successfully Initial bedhcp4_relay.... Initial bedhcp6_server.... Initial bedhcp6_serverpool.... Initial bevlanTerm.... Initial bepppiface.... zcmdTr98SyncTr98WANConnectNum: obj 63672 seqnum 218 Initial bepppifaceipcp.... Initial bedhcp4_client.... Initial bedhcp6_client.... 1970-01-01 00:01:11 zcmd<518>, be_dhcp6_client_config_init.c:29, beConfigBoot(), INFO: boot Dhcp6 Client Initial beradvd.... Initial bedns.... Initial bedns_route.... Initial bedns_server.... zcmdTr98MtRecognizeRDMappingOnRelease: objnum 87708, List obj 87708 zcmdTr98MtRecognizeRDMappingOnRelease: objnum 87708, List obj 87708 zcmdTr98MtRecognizeRDMappingOnRelease: objnum 87708, List obj 87708 Initial benat_port_map.... Initial benat_port_trigger.... Initial benat_addr_mapping.... Initial begre_tunnel.... modprobe ip_gre modprobe: module ip_gre not found in modules.dep Initial besessCtl.... /bin/sh: can't create /proc/zy_nf_ct_udp_STB_port: nonexistent directory /bin/sh: can't create /proc/zy_nf_ct_udp_STB_timeout: nonexistent directory Initial befirewall.... getL1InterfaceUpstream: 561 USB.Interface.1 getL1InterfaceUpstream: 561 USB.Interface.1 Initial betr69.... Initial beddns.... Initial betime.... Initial bediagnostic.... killall: tmsctl: no process killed Initial beschedule.... Initial beparenCtl.... Initial beqos.... Initial beqosQueue.... Initial beqosClass.... Initial beqosShaper.... Initial beqosPolicer.... Initial be6rd.... Initial beigmp.... cp: can't stat '/etc/mcpd_igmp.conf': No such file or directory beigmp! /bin/sh: can't create /proc/zy_igmp_noipsrcaddr_enable: nonexistent directory restart DNSMASQ... [beIgmpCreateCfg](122) Failed. Initial besnmp.... Boot SNMP Initial bemld.... 1970-01-01 00:01:13 dnsmasq<1314>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 23 bind server socket 9 on /var/lib/.sock/zcfg_sockaddr23 successfully cp: can't stat '/etc/mcpd_mld.conf': No such file or directory cat: can't open '/var/run/ecmh.pid': No such file or directory sh: you need to specify whom to kill Initial bevcAutoHunt.... Initial bevlanAutoHunt.... Initial beupnp.... Initial bemacfilter.... Initial bemacfilter_whitelist.... Initial beuserinterface.... Initial beremoMgmt.... Initial bechangehosticon.... Initial behosts.... Initial behostshost.... Initial becert.... Initial beportmirror.... Initial bedslite.... Initial beSTBVendorID.... Initial berip.... killall: ripd: no process killed writing RSA key Initial betr64.... Initial bewwanbackup.... Initial besamba.... Initial http with port(443), SSL enable. Initial http with port(80), SSL disable. 1970-01-01 00:01:15 zhttpd<1347>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 15 bind server socket 58 on /var/lib/.sock/zcfg_sockaddr15 successfully wwanbackup info: WWANBACKUP start wwanbackup info: WWANBACKUP_DEBUG is 0 starting smbd. samba start ok Initial bevoiceSrv.... Initial bevoiceCap.... Initial bevoiceCapSip.... bePppIfaceSet: PPP.Interface.1 bePppIfaceSet : Enable new or enable existing Initial bevoiceCapCodec.... Initial bevoiceCommon.... Initial bevoiceProf.... Initial bevoiceProfSip.... Initial bevoiceProfFaxT38.... Initial bevoiceProfNumberingPlan.... Initial bevoiceProfNumberingPlanPrefixInfo.... Initial bevoiceProfRTP.... Initial bevoiceProfRTPSRTP.... Initial bevoiceLine.... Initial bevoiceLineSip.... Initial bevoiceLineProc.... Initial bevoiceLineCallingFeatures.... Initial bevoiceLineCodecList.... Initial bevoiceLineStats.... Initial bevoiceLineRinger.... Initial bevoiceLineRingerDescription.... Initial bevoicePhyIntf.... Initial bevoiceSpeedDialBookList.... Initial bevoiceCallPolicyBook.... Initial bevoiceCallPolicyBookList.... Initial bevoiceCallStatus.... Initial bednsentry.... Initial bezx.... Initial bedlna.... Initial bevlangroup.... Initial beTFTPServerName.... Initial bespeedtest.... Initial beoneconnect.... Initial beoneconnectPCRule.... Initial bePwrMgmt.... Initial bewifi_easymesh.... Initial bewifi_onessid.... Back-end module init finished Initial USB driver... turn on ztr69 zcfgFeTr98QueryHandleRoutInit cwmp_get_acsInfo: reset redirect server 1970-01-01 00:01:18 ztr69<1557>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 9 bind server socket 59 on /var/lib/.sock/zcfg_sockaddr9 successfully /bin/sh: /etc/init.d/mcpd.sh: not found START enable Lan and Wan... /bin/sh: /usr/sbin/zy1905: not found /bin/sh: /usr/sbin/zy1905Monitor: not found rm: can't remove '/tmp/app_sock': No such file or directory TR181 object IP.Interface.1 writing RSA key bridge name br0 Initial http with port(20443), SSL enable. database_init : /data/netprb_db_ver database_init : database_ver 18 database_init : Create Device table database_init : Create Sub Interface table database_init : Create L2 Device Functions table arp_init : arp_event->event_id 1 layer2_init : layer2_event->event_id 2 oui_init : oui_event->event_id 3 ethlink_init : ethlink_event->event_id 4 zy1905_init : zy1905_event->event_id 5 [/sbin/wwan-package-match.sh] VID 1d6b no match, exit json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory 1970-01-01 00:01:22 zupnp<1638>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 17, select() wait forever, EID = 1, type = 2 with reply, oid = 65676 1970-01-01 00:01:22 esmd<524>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 2, select() wait forever, EID = 1, type = 1 with reply, oid = 38004 [/sbin/wwan-package-match.sh] VID 1d6b no match, exit 1970-01-01 00:01:23 zhttpd_rest<1628>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 77, select() wait forever, EID = 1, type = 2 with reply, oid = 114828 1970-01-01 00:01:23 one_connect_monitor<1695>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 78, select() wait forever, EID = 1, type = 2 with reply, oid = 126708 [/sbin/usb-hotplug.sh] add /var/usb/usb1 1970-01-01 00:01:24 zupnp<1638>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 17, select() wait forever, EID = 1, type = 2 with reply, oid = 65676 1970-01-01 00:01:24 esmd<524>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 2, select() wait forever, EID = 1, type = 1 with reply, oid = 38004 json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory 1970-01-01 00:01:25 zhttpd_rest<1628>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 77, select() wait forever, EID = 1, type = 2 with reply, oid = 114828 1970-01-01 00:01:25 one_connect_monitor<1695>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 78, select() wait forever, EID = 1, type = 2 with reply, oid = 126708 1970-01-01 00:01:26 zupnp<1638>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 17, select() wait forever, EID = 1, type = 2 with reply, oid = 65676 1970-01-01 00:01:26 esmd<524>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 2, select() wait forever, EID = 1, type = 1 with reply, oid = 38004 1970-01-01 00:01:27 zhotplugd<1526>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 32, select() wait forever, EID = 1, type = 1 with reply, oid = 41016 json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory 1970-01-01 00:01:27 zhttpd_rest<1628>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 77, select() wait forever, EID = 1, type = 2 with reply, oid = 114828 json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory 1970-01-01 00:01:27 one_connect_monitor<1695>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 78, select() wait forever, EID = 1, type = 2 with reply, oid = 126708 1970-01-01 00:01:28 zupnp<1638>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 17, select() wait forever, EID = 1, type = 2 with reply, oid = 65676 1970-01-01 00:01:28 esmd<524>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 2, select() wait forever, EID = 1, type = 1 with reply, oid = 38004 1970-01-01 00:01:29 zhotplugd<1526>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 32, select() wait forever, EID = 1, type = 1 with reply, oid = 41016 1970-01-01 00:01:29 zhttpd_rest<1628>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 77, select() wait forever, EID = 1, type = 2 with reply, oid = 114828 1970-01-01 00:01:29 one_connect_monitor<1695>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 78, select() wait forever, EID = 1, type = 2 with reply, oid = 126708 json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory 1970-01-01 00:01:30 zupnp<1638>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 17, select() wait forever, EID = 1, type = 2 with reply, oid = 65676 1970-01-01 00:01:30 esmd<524>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 2, select() wait forever, EID = 1, type = 1 with reply, oid = 38004 1970-01-01 00:01:31 zhotplugd<1526>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 32, select() wait forever, EID = 1, type = 1 with reply, oid = 41016 1970-01-01 00:01:31 zhttpd_rest<1628>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 77, select() wait forever, EID = 1, type = 2 with reply, oid = 114828 1970-01-01 00:01:31 one_connect_monitor<1695>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 78, select() wait forever, EID = 1, type = 2 with reply, oid = 126708 json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory 1970-01-01 00:01:32 zupnp<1638>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 17, select() wait forever, EID = 1, type = 2 with reply, oid = 65676 1970-01-01 00:01:32 esmd<524>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 2, select() wait forever, EID = 1, type = 1 with reply, oid = 38004 1970-01-01 00:01:33 zhotplugd<1526>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 32, select() wait forever, EID = 1, type = 1 with reply, oid = 41016 1970-01-01 00:01:33 zhttpd_rest<1628>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 77, select() wait forever, EID = 1, type = 2 with reply, oid = 114828 1970-01-01 00:01:33 one_connect_monitor<1695>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 78, select() wait forever, EID = 1, type = 2 with reply, oid = 126708 json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory 1970-01-01 00:01:34 zupnp<1638>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 17, select() wait forever, EID = 1, type = 2 with reply, oid = 65676 1970-01-01 00:01:34 esmd<524>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 2, select() wait forever, EID = 1, type = 1 with reply, oid = 38004 1970-01-01 00:01:35 zhotplugd<1526>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 32, select() wait forever, EID = 1, type = 1 with reply, oid = 41016 1970-01-01 00:01:35 zcmd<459>, zcmd.c:6410, main(), WARNING: process msg type = 2 with reply, oid = 65676, from EID = 17 by 14553 ms zyExtRemoteMgmtSrvObjGet : Enter l3fwdObjGet : Enter l3fwdGetDfGwByRtTable: enter, 4 DeviceDiscRespPayload={ "ApiName": "ZYXEL RESTful API", "ModelName": "VMG8825-T50", "SoftwareVersion": "V5.50(ABPY.1)b11", "DeviceMode": "Router", "SupportedApiVersion": [ { "ApiVersion": "1.0", "LoginURI": "\/api\/v1\/UserLogin", "Protocol": "HTTPS", "HttpsPort": 20443 } ], "MAC": "08:26:97:DA:DD:80" } 1970-01-01 00:01:35 zhttpd_rest<1628>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 77 bind server socket 13 on /var/lib/.sock/zcfg_sockaddr77 successfully hotplug:beUsbPortSet: USB Port Alias is cpe- hotplug:beUsbPortSet: USB Port Type is Device db_init() Open database: not an error APP Agent UDP socket ready! l3fwdGetDfGwByRtTable: ifname = l3fwdGetDfGwByRtTable: No find default gateway interface!! Restarting ZyIMS VoIP ppe cmd done! ppe cmd done! [/sbin/wwan-package-match.sh] VID 1d6b no match, exit ppe cmd done! killall: voiceApp: no process killed ppe cmd done! killall: mm.exe: no process killed ppe cmd done! ppe cmd done! killall: icf.exe: no process killed ppe cmd done! json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory ppe cmd done! json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory done device ra0 is already a member of a bridge; can't enslave it to bridge br0. device ra1 is already a member of a bridge; can't enslave it to bridge br0. [/sbin/wwan-package-match.sh] VID 1d6b no match, exit bePtmLinkStatGet : Enter ============================================================================ UPnP Mapping table Dump: TR98 Object Name : UPnP service Id InternetGatewayDevice.Layer3Forwarding : urn:upnp-org:serviceId:Layer3Forwarding.1 ============================================================================ l3fwdObjGet : Enter l3fwdGetDfGwByRtTable: enter, 4 /bin/sh: zy1905App: not found l3fwdGetDfGwByRtTable: ifname = l3fwdGetDfGwByRtTable: No find default gateway interface!! [/sbin/usb-hotplug.sh] add /var/usb/usb2 json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory [MM] main(): getpid = 1882 AppRegisterSignal(): mm.exe pid = 1882 UITimer_Init()... [MM]dspDriverDeinit(): DSP & Phone Port driver is already De-initialized ==> skip the action!! UITimerProc(): The UI Timer System (thread task: 'vo-USR-UItimer', pid=1882) is running... json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory AppRegisterSignal(): voiceApp pid = 1883 UITimer_Init()... 1970-01-01 00:01:39 voiceApp<1883>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 12 bind server socket 10 on /var/lib/.sock/zcfg_sockaddr12 successfully ### ZyIMS VoIP TR-104 Config Data Init Procedure Start ### UITimerProc(): The UI Timer System (thread task: 'vo-USR-UItimer', pid=1883) is running... 1970-01-01 00:01:40 zupnp<1638>, zcfg_msg.c:598, zcfg_msg_serverInit(), INFO: EID 17 bind server socket 14 on /var/lib/.sock/zcfg_sockaddr17 successfully main(): getpid = 1881 [ENTERED]:ICF_ES INFO: AUTO_SCALE: 1 INFO: MODE_OF_OPERATION: 0 INFO: SIP_COMPACT_HDRS: NO INFO: NW_TRACE_ENABLED: YES INFO: ICF_DEF_SIP_SERVER_PORT: 6062 INFO: ICF_DEF_SIP_PROXY_PORT: 6061 INFO: TRANSPORT_MODE: 0 INFO: ICF_SYS_RESOURCE_LIMIT: 1 [ENTERING]:icf_es_init [ICF_ES]:PORT initalized succesfully icf_port_open_ipc_channel path = /var/iptk_es.chanl the open channel succeded exit from the es init icf_register_signal(): icf.exe pid = 1881 json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory 1970-01-01 00:01:42 voiceApp<1883>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 12, select() wait forever, EID = 1, type = 1 with reply, oid = 468 1970-01-01 00:01:42 esmd<524>, zcfg_msg.c:235, _msg_recv(), WARNING: EID = 2, select() wait forever, EID = 1, type = 1 with reply, oid = 61608 1970-01-01 00:01:42 zcmd<459>, zcfg_msg.c:242, _msg_recv(), WARNING: EID = 1, select() wait for 2000 milli-seconds, EID = 12, type = 2004 with reply, oid = 0 1970-01-01 00:01:42 zcmd<459>, zcfg_msg.c:844, zcfg_msg_sendAndGetReply(), ERROR: fail to receive message. ret = -1 <<Error>> beVoiceCapConfigStatsUpdate() beVoiceSendMsgToZyIMSAndGetReply failed -5 use default list 1970-01-01 00:01:42 zcmd<459>, zcmd.c:6410, main(), WARNING: process msg type = 1 with reply, oid = 468, from EID = 12 by 2031 ms hotplug:beUsbPortSet: USB Port Alias is cpe- hotplug:beUsbPortSet: USB Port Type is Device 1970-01-01 00:01:42 esmd<524>, esmd.c:1565, processRequest(), WARNING: process msg type = 235 without reply, oid = 0, from EID = 1 by 24824 ms zcmd.c line 5582, zcmdReqProcess() : get ZCFG_MSG_INIT_DATAMODEL_FIN ECONET/zcmd_wrapper.c line 2046, zcmdEnableConfigSave() : enable tr98mapTableSaveFlag and configSaveFlag tr104ConvertPortsType(): <<Error>> INVALID parameter value : '' !! tr104ConvertDialingType(): <<Error>> INVALID parameter value : '' !! tr104ConvertDialToneType(): <<Error>> INVALID parameter value : '' !! tr104ConvertReceiveToneType(): <<Error>> INVALID parameter value : '' !! tr104ConvertCallerIDType(): <<Error>> INVALID parameter value : '' !! tr104ConvertCallerIDPayloadType(): <<Error>> INVALID parameter value : '' !! tr104ConvertTASType(): <<Error>> INVALID parameter value : '' !! tr104ConvertTASType(): <<Error>> INVALID parameter value : '' !! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! tr104ConvertPortsType(): <<Error>> INVALID parameter value : '' !! tr104ConvertDialingType(): <<Error>> INVALID parameter value : '' !! tr104ConvertDialToneType(): <<Error>> INVALID parameter value : '' !! tr104ConvertReceiveToneType(): <<Error>> INVALID parameter value : '' !! tr104ConvertCallerIDType(): <<Error>> INVALID parameter value : '' !! tr104ConvertCallerIDPayloadType(): <<Error>> INVALID parameter value : '' !! tr104ConvertTASType(): <<Error>> INVALID parameter value : '' !! tr104ConvertTASType(): <<Error>> INVALID parameter value : '' !! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory tr104ConvertRegType(): <<Error>> INVALID parameter value : '' !! count =3 1=/userfs/bin/mapd_cli 2=/tmp/mapd_ctrl mapd_interface_ctrl_open failed Can't connect to /tmp/mapd_ctrl json_object_from_file: error opening file /tmp/dump.txt: No such file or directory [initALTable] second chance - dump information is not ready. Update 1905 information Error!! tr104ConvertCWStatus(): <<Error>> INVALID parameter value : '' !! tr104ConvertRegType(): <<Error>> INVALID parameter value : '' !! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! tr104ConvertCWStatus(): <<Error>> INVALID parameter value : '' !! json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory ### ZyIMS VoIP TR-104 Config Data Init Procedure Successfully Finished ### MM:voiceDspCoreInit(): Entering... [MM]dspDriverInit(): Start to initialize the DSP (& Phone Port) driver by calling 'PhoneInit(countryCode=24)'... PhoneInit(): region: 'NLD'. Country Name:NLD result:9475208 result:-9475208 VDSP_GetInstance:278 MM:voiceDspCoreInit(): after calling 'dsp_driver_itf.c/dspDriverGetInitData(initData@0x0, initDataLength=0)' to get the inited data of the MM part 'Endpoint_itf_mm.c/cmPhysEndpt[MAX_ENDPT]'... MM:voiceDspCoreInit(): after calling 'voiceEventIpcSendToVoiceApp()' to send the response message 'VOICE_DSP_INIT_RSP' back to [voiceApp]... MM:voiceDspCoreInit(): Exiting...with ret=1 & ret2=1 (MM_SUCCESS(1), MM_FAILURE(0)) [Adam] Change log level to (EVA_LOG_ERR). [GDI] Change log level to (EVA_LOG_ERR). fxsPhoneIOP_hookFlashDetecTimerSet(): <<Error>>Invalid input timer value {flashTimerMin=0, flashTimerMax=0} for the FXS phone port index-0!! The valid condition is: both values should >= 0 except these two cases - (i)both values == 0, and (ii)(flashTimerMin >= flashTimerMax) while both values > 0! fxsPhoneIOP_hookFlashDetecTimerSet(): <<Error>>Invalid input timer value {flashTimerMin=0, flashTimerMax=0} for the FXS phone port index-1!! The valid condition is: both values should >= 0 except these two cases - (i)both values == 0, and (ii)(flashTimerMin >= flashTimerMax) while both values > 0! voiceDspInit(): <<Error>> The Phone (DSP Init) Data: LocationPtr=0x00000000, Size=-1!! DSP state is Inactive , so exit PhoneInitEventCb now DSP activated success taskCreate()... voiceDspInit(): Leaving with return 0... phonePortVMWISet enters (for 'FXS' phone, phid=8 (8:All 'Ports' of the type), vmwiSigType=2 (1:SigOn,2:SigOff,0:SigNone))... in PhoneEventCb , the event 18 is not support ! in PhoneEventCb , the event 18 is not support ! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! taskCreate()... flushVoipRoutePolicy(): cmd = iptables -t mangle -F IP_ROUTE2_VOIP ### ZyIMS VoIP Start-up Procedure Finished ### zyRegionLListAdd(): <<WARN>> VoIP Country/Region Code 'MEX' is NOT supported, Skip it!! zyRegionLListAdd(): <<WARN>> VoIP Country/Region Code 'CYP' is NOT supported, Skip it!! json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory 1970-01-01 00:01:49 voiceApp<1883>, zcfg_msg.c:419, _msg_send(), ERROR: fail to sendto /var/lib/.sock/zcfg_sockaddr1-1573323, errno = 2(No such file or directory), srcEid = 12, dstEid = 1, type = 103 without reply, oid = 0 json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory get_iface_ipv4_address(): <<Error>> ioctl socket 'SIOCGIFADDR' fail for ifName() ==> try to get IP address info by searching the 'iface_ipv4_address_list[]' array database alternatively!! get_iface_ipv4_address(): <<Error>> Can't find any matched ifName() even in the 'iface_ipv4_address_list[]' array database!! mmCfgSelfIp()/SipAcctId=0: <<Error>> calling 'get_iface_ipv4_address()' to get the IP Address FAIL for the interface pProf->ZyXEL_ActiveBoundIfName='' (where pProf->name='ChangeMe', ZyXEL_BoundIfName='Multi_WAN', ZyXEL_BoundIfList='IP.Interface.4,IP.Interface.7,IP.Interface.10', ZyXEL_BoundIpAddr='') ==> return FALSE now!! mmCfgOfRtpInfo()/SipAcctId=0: <<Error>> MM -> IPTK : 'mmCfgSelfIp(ICF_CFG_SET_SELF_IP_REQ)' FAILed ==> return FALSE now!! mmIptkCfgOfSipAccount(PID = 1883): <<Error>> 'mmCfgOfRtpInfo(sipAccountId=0)' FAIL ===> try to continue processing the next SIP Account!! get_iface_ipv4_address(): <<Error>> ioctl socket 'SIOCGIFADDR' fail for ifName() ==> try to get IP address info by searching the 'iface_ipv4_address_list[]' array database alternatively!! get_iface_ipv4_address(): <<Error>> Can't find any matched ifName() even in the 'iface_ipv4_address_list[]' array database!! mmCfgSelfIp()/SipAcctId=1: <<Error>> calling 'get_iface_ipv4_address()' to get the IP Address FAIL for the interface pProf->ZyXEL_ActiveBoundIfName='' (where pProf->name='ChangeMe', ZyXEL_BoundIfName='Multi_WAN', ZyXEL_BoundIfList='IP.Interface.4,IP.Interface.7,IP.Interface.10', ZyXEL_BoundIpAddr='') ==> return FALSE now!! mmCfgOfRtpInfo()/SipAcctId=1: <<Error>> MM -> IPTK : 'mmCfgSelfIp(ICF_CFG_SET_SELF_IP_REQ)' FAILed ==> return FALSE now!! mmIptkCfgOfSipAccount(PID = 1883): <<Error>> 'mmCfgOfRtpInfo(sipAccountId=1)' FAIL ===> try to continue processing the next SIP Account!! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! rm: can't remove '/tmp/app_sock': No such file or directory aging_en: 1, aging time: 5 aging_unit: 0, aging_cnt: 4 write reg: a0, value: 4000 get_if_info for br0 interface index is 19 get_if_info OK Clean up temporary socket ppe cmd done! ppe cmd done! bind_arp: ifindex=19 Binding to ifindex 19 ppe cmd done! ppe cmd done! ppe cmd done! ppe cmd done! bind_arp: ifindex=16 Binding to ifindex 16 ppe cmd done! ppe cmd done! MAC: 0x7fa8dc2c, len = 6 0x0000 : 08 26 97 da dd 81 bind_arp: ifindex=20 Binding to ifindex 20 done bind_arp: ifindex=21 Binding to ifindex 21 bind_arp: ifindex=22 Binding to ifindex 22 bind_arp: ifindex=17 Binding to ifindex 17 rai0 bbp:2308=303 /bin/sh: can't create /proc/tc3162/lan_to_wifi_rps: nonexistent directory bind_arp: ifindex=28 Binding to ifindex 28 bind_arp: ifindex=29 Binding to ifindex 29 zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! bind_arp: ifindex=30 Binding to ifindex 30 zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! opClass = 81, chn_num = 13 opClass = 83, chn_num = 9 opClass = 84, chn_num = 9 opClass = 81, chn_num = 13 opClass = 83, chn_num = 9 opClass = 84, chn_num = 9 opClass = 81, chn_num = 13 opClass = 83, chn_num = 9 opClass = 84, chn_num = 9 device rai0 is already a member of a bridge; can't enslave it to bridge br0. killall: p1905_managerd: no process killed opClass = 81, chn_num = 13 opClass = 83, chn_num = 9 opClass = 84, chn_num = 9 device rai1 is already a member of a bridge; can't enslave it to bridge br0. opClass = 115, chn_num = 4 opClass = 118, chn_num = 4 opClass = 121, chn_num = 11 opClass = 116, chn_num = 2 opClass = 119, chn_num = 2 opClass = 122, chn_num = 5 opClass = 117, chn_num = 2 opClass = 120, chn_num = 2 opClass = 123, chn_num = 5 opClass = 128, chn_num = 4 opClass = 129, chn_num = 2 opClass = 130, chn_num = 4 opClass = 115, chn_num = 4 opClass = 118, chn_num = 4 opClass = 121, chn_num = 11 opClass = 116, chn_num = 2 opClass = 119, chn_num = 2 opClass = 122, chn_num = 5 opClass = 117, chn_num = 2 opClass = 120, chn_num = 2 opClass = 123, chn_num = 5 opClass = 128, chn_num = 4 opClass = 129, chn_num = 2 opClass = 130, chn_num = 4 opClass = 115, chn_num = 4 opClass = 118, chn_num = 4 opClass = 121, chn_num = 11 opClass = 116, chn_num = 2 opClass = 119, chn_num = 2 opClass = 122, chn_num = 5 opClass = 117, chn_num = 2 opClass = 120, chn_num = 2 opClass = 123, chn_num = 5 opClass = 128, chn_num = 4 opClass = 129, chn_num = 2 opClass = 130, chn_num = 4 device rai3 is already a member of a bridge; can't enslave it to bridge br0. opClass = 115, chn_num = 4 opClass = 118, chn_num = 4 opClass = 121, chn_num = 11 opClass = 116, chn_num = 2 opClass = 119, chn_num = 2 opClass = 122, chn_num = 5 opClass = 117, chn_num = 2 opClass = 120, chn_num = 2 opClass = 123, chn_num = 5 opClass = 128, chn_num = 4 opClass = 129, chn_num = 2 opClass = 130, chn_num = 4 [WAPP]map_send_wirelss_inf_info send info ra0, role: wiap, dev type = 1 MAC Address = 08:26:97:da:dd:81 send info ra1, role: wiap, dev type = 1 MAC Address = 0a:26:97:da:dd:81 send info ra2, role: wiap, dev type = 1 MAC Address = 0a:26:97:ea:dd:81 send info ra3, role: wiap, dev type = 1 MAC Address = 0a:26:97:fa:dd:81 send info rai0, role: wiap, dev type = 1 MAC Address = 08:26:97:da:dd:82 send info rai1, role: wiap, dev type = 1 MAC Address = 0a:26:97:da:dd:82 send info rai2, role: wiap, dev type = 1 MAC Address = 0a:26:97:ea:dd:82 send info rai3, role: wiap, dev type = 1 MAC Address = 0a:26:97:fa:dd:82  inf_count = 8   0 name ra0 ch 2, phymode [N] role [wiap]  1 name ra1 ch 2, phymode [N] role [wiap]  2 name ra2 ch 2, phymode [N] role [wiap]  3 name ra3 ch 2, phymode [N] role [wiap]  4 name rai0 ch 52, phymode [AC] role [wiap]  5 name rai1 ch 52, phymode [AC] role [wiap]  6 name rai2 ch 52, phymode [AC] role [wiap]  7 name rai3 ch 52, phymode [AC] role [wiap] route: SIOCADDRT: File exists killall: mapd: no process killed daemon mapd attached \x00/tmp/wapp_ctrl ctrler_found [WAPP]map_send_wirelss_inf_info send info ra0, role: wiap, dev type = 1 MAC Address = 08:26:97:da:dd:81 send info ra1, role: wiap, dev type = 1 MAC Address = 0a:26:97:da:dd:81 send info ra2, role: wiap, dev type = 1 MAC Address = 0a:26:97:ea:dd:81 send info ra3, role: wiap, dev type = 1 MAC Address = 0a:26:97:fa:dd:81 send info rai0, role: wiap, dev type = 1 MAC Address = 08:26:97:da:dd:82 send info rai1, role: wiap, dev type = 1 MAC Address = 0a:26:97:da:dd:82 send info rai2, role: wiap, dev type = 1 MAC Address = 0a:26:97:ea:dd:82 send info rai3, role: wiap, dev type = 1 MAC Address = 0a:26:97:fa:dd:82 Profile Count to host = 0 rm: can't remove '/tmp/app_sock': No such file or directory bridge name br0 database_init : /data/netprb_db_ver database_init : database_ver 18 database_init : Create Device table database_init : Create Sub Interface table database_init : Create L2 Device Functions table arp_init : arp_event->event_id 1 layer2_init : layer2_event->event_id 2 oui_init : oui_event->event_id 3 ethlink_init : ethlink_event->event_id 4 zy1905_init : zy1905_event->event_id 5 agentDataRecv: Start to receiving... 0 ssid=TMNL-DADD81, autmode=0x0020, encryptype=0x0008, key=MRFNQVMQMXFBR4R9 bh_bss=0, fh_bss=1 send BH config to ra0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 1 ssid=TMNL-DADD81_guest1, autmode=0x0020, encryptype=0x0008, key=MRFNQVMQMXFBR4R9 bh_bss=0, fh_bss=1 send BH config to ra0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 2 ssid=TMNL-DADD81_guest2, autmode=0x0020, encryptype=0x0008, key=MRFNQVMQMXFBR4R9 bh_bss=0, fh_bss=1 send BH config to ra0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 3 ssid=TMNL-DADD81_guest3, autmode=0x0020, encryptype=0x0008, key=MRFNQVMQMXFBR4R9 bh_bss=0, fh_bss=1 send BH config to ra0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 1-iwpriv ra0 set AuthMode=WPA2PSK; /bin/sh: wifi_config_save: not found 2-iwpriv ra0 set EncrypType=AES; /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found 1-iwpriv ra1 set AuthMode=WPA2PSK; /bin/sh: wifi_config_save: not found 2-iwpriv ra1 set EncrypType=AES; /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found 1-iwpriv ra2 set AuthMode=WPA2PSK; /bin/sh: wifi_config_save: not found 2-iwpriv ra2 set EncrypType=AES; /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found 1-iwpriv ra3 set AuthMode=WPA2PSK; /bin/sh: wifi_config_save: not found 2-iwpriv ra3 set EncrypType=AES; /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found 0 ssid=TMNL-DADD81, autmode=0x0020, encryptype=0x0008, key=MRFNQVMQMXFBR4R9 bh_bss=0, fh_bss=1 send BH config to ra0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 1 ssid=TMNL-DADD81_guest1, autmode=0x0020, encryptype=0x0008, key=MRFNQVMQMXFBR4R9 bh_bss=0, fh_bss=1 send BH config to ra0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 2 ssid=TMNL-DADD81_guest2_5G, autmode=0x0020, encryptype=0x0008, key=MRFNQVMQMXFBR4R9 bh_bss=0, fh_bss=1 send BH config to ra0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to ra3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai0 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai1 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai2 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 send BH config to rai3 wapd sends WPAPSK = MRFNQVMQMXFBR4R9 3 ssid=29a022df555f3c37f84a367e153831c, autmode=0x0020, encryptype=0x0008, key=d46025d0ff175f7d55ae756de8952d5a bh_bss=1, fh_bss=0 send BH config to ra0 wapd sends WPAPSK = d46025d0ff175f7d55ae756de8952d5a send BH config to ra1 wapd sends WPAPSK = d46025d0ff175f7d55ae756de8952d5a send BH config to ra2 wapd sends WPAPSK = d46025d0ff175f7d55ae756de8952d5a send BH config to ra3 wapd sends WPAPSK = d46025d0ff175f7d55ae756de8952d5a send BH config to rai0 wapd sends WPAPSK = d46025d0ff175f7d55ae756de8952d5a send BH config to rai1 wapd sends WPAPSK = d46025d0ff175f7d55ae756de8952d5a send BH config to rai2 wapd sends WPAPSK = d46025d0ff175f7d55ae756de8952d5a send BH config to rai3 wapd sends WPAPSK = d46025d0ff175f7d55ae756de8952d5a 1-iwpriv rai0 set AuthMode=WPA2PSK; /bin/sh: wifi_config_save: not found 2-iwpriv rai0 set EncrypType=AES; /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found 1-iwpriv rai1 set AuthMode=WPA2PSK; /bin/sh: wifi_config_save: not found 2-iwpriv rai1 set EncrypType=AES; /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found 1-iwpriv rai2 set AuthMode=WPA2PSK; /bin/sh: wifi_config_save: not found 2-iwpriv rai2 set EncrypType=AES; /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found 1-iwpriv rai3 set AuthMode=WPA2PSK; /bin/sh: wifi_config_save: not found 2-iwpriv rai3 set EncrypType=AES; /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found /bin/sh: wifi_config_save: not found json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory json_object_from_file: error opening file /tmp/zy1905.json: No such file or directory count =3 1=/userfs/bin/mapd_cli 2=/tmp/mapd_ctrl Succesfully opened connection to mapd zywifid> [ERROR] push_wifidReqProcess:590: Ignore request handler[ZCFG_MSG_WLAN_GET_CMD(4017)]. Internal Error ~! count =3 1=/userfs/bin/mapd_cli 2=/tmp/mapd_ctrl Succesfully opened connection to mapd count =3 1=/userfs/bin/mapd_cli 2=/tmp/mapd_ctrl Succesfully opened connection to mapd count =3 1=/userfs/bin/mapd_cli 2=/tmp/mapd_ctrl Succesfully opened connection to mapd


COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2023/05/23 23:28
  • by rupurudu1