Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| inbox:toh:zyxel:nbg7815_armor_g5 [2024/10/09 06:26] – minor error fixing pwned | inbox:toh:zyxel:nbg7815_armor_g5 [2024/12/13 11:35] – [Hardware] pwned | ||
|---|---|---|---|
| Line 10: | Line 10: | ||
| ===== Hardware ===== | ===== Hardware ===== | ||
| - | ^ CPU ^ Ram ^ Flash ^ Network | + | ^ Architecture |
| - | | Qualcomm IPQ8074A @ 2.2 GHz | 1 GB | 4 GB eMMC + 8 MB SPI NOR | 1x 1/2.5/5/10 GbE 1x 1/2.5 GbE 4x 1 GbE | a/ | + | ^ Vendor |
| - | < | + | ^ Bootloader |
| - | ^ Architecture | + | ^ System-On-Chip |
| - | ^ Vendor | + | ^ CPU/ |
| - | ^ Bootloader | + | ^ Flash-Chip |
| - | ^ System-On-Chip | + | ^ Flash size | 4 GB eMMC + 8 MB SPI NOR | |
| - | ^ CPU/ | + | ^ RAM |
| - | ^ Flash-Chip | + | ^ Bluetooth |
| - | ^ Flash size | 4 GB eMMC + 8 MB SPI NOR | | + | ^ Wireless |
| - | ^ RAM | + | ^ Wireless |
| - | ^ Bluetooth | + | ^ Ethernet |
| - | ^ Wireless | + | ^ Ethernet |
| - | ^ Wireless | + | ^ Switch |
| - | ^ Ethernet | + | ^ USB |
| - | ^ Ethernet | + | ^ [[# |
| - | ^ Switch | + | ^ PSU |
| - | ^ USB | + | |
| - | ^ [[# | + | |
| - | ^ PSU | + | |
| - | </ | + | |
| \\ | \\ | ||
| Line 269: | Line 265: | ||
| <tabbox Step 6>< | <tabbox Step 6>< | ||
| - | cat <<' | + | cat <<' |
| # check files | # check files | ||
| Line 332: | Line 328: | ||
| - [[#Opening the case|Open the device case.]] | - [[#Opening the case|Open the device case.]] | ||
| - Connect to the device via [[# | - Connect to the device via [[# | ||
| - | - [[#U-Boot access|Access the device via bootloader.]] | + | - [[#Bootloader/U-Boot access|Access the device via bootloader.]] |
| - [[#TFTP boot OpenWrt|TFTP boot OpenWrt]] to either reinstall or fix a broken installation | [[#TFTP flash OEM firmware|TFTP flash OEM firmware]] to purge OpenWrt. | - [[#TFTP boot OpenWrt|TFTP boot OpenWrt]] to either reinstall or fix a broken installation | [[#TFTP flash OEM firmware|TFTP flash OEM firmware]] to purge OpenWrt. | ||
| \\ | \\ | ||
| Line 338: | Line 334: | ||
| ==== Opening the case ==== | ==== Opening the case ==== | ||
| - | <WRAP BOX> | + | - Remove the two rubber crosses from the device' bottom side. |
| - | FIXME //Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, | + | - Unscrew the two screws appearing after step 1. |
| - | </ | + | - Remove the socket. |
| + | - After step 3. another four screws | ||
| + | - Around the device' | ||
| + | - Keep the device with bottom side up and pry it up carefully around the case to remove the bottom side. Start at the side where the connectors are lead out. | ||
| + | |||
| + | *) You will likely break some of them. Especially those on the left or right side. The clips at the front' | ||
| + | \\ | ||
| + | |||
| + | {{media: | ||
| + | {{media: | ||
| + | {{media: | ||
| ==== Serial ==== | ==== Serial ==== | ||
| Line 399: | Line 405: | ||
| <tabbox password> | <tabbox password> | ||
| < | < | ||
| - | sh tool.sh | + | sh tool.sh 013D72FF0710 |
| </ | </ | ||
| - Put the output from paragraph 4. in the terminal and press enter:\\ \\ < | - Put the output from paragraph 4. in the terminal and press enter:\\ \\ < | ||