ZyXEL NBG7815 (Armor G5)

AX6000 (1200+4800 Mbps) 12-Stream Multi-Gigabit WiFi 6 Router. 2.4GHz AX: 4×4 (Tx/Rx) 1024 QAM 20/40 MHz, up to 1.2 Gbps. 5GHz AX: 8×8 (Tx/Rx) 1024 QAM 20/40/80/160 MHz, up to 4.8 Gbps.

Zyxel NBG7815 (Armor G5) Zyxel NBG7815 (Armor G5)

ZyXEL NBG7815 product page

CPU Ram Flash Network Wifi USB Serial
Qualcomm IPQ8074A @ 2.2 GHz 1 GB 4 GB eMMC + 8 MB SPI NOR 1x 1/2.5/5/10 GbE 1x 1/2.5 GbE 4x 1 GbE a/b/g/n/ac/ax 1x 3.1 Gen2 Yes

Click to display ⇲

Click to hide ⇱

Architecture ARMv8
Vendor Qualcomm
Bootloader U-Boot + ZyXEL zLoader
System-On-Chip Qualcomm IPQ8074A
CPU/Speed Quad Core 2.2 GHz
Flash-Chip Kingston EMMC04G-M627 + Winbond W25Q64DW
Flash size 4 GB eMMC + 8 MB SPI NOR
RAM 1 GB 2x Nanya NT5CC256M16ER-EK
Bluetooth CSR8811 using HSUART
Wireless QCN5024 bgn+ax
Wireless QCN5054 an+ac+ax
Ethernet 4x 10/100/1000 Mbps + 1x 1/2.5 GbE + 1x 1/2.5/5/10 GbE
Ethernet ETH chip1: IPQ8074A + ETH chip2: QCA8081 + ETH chip3: Aquantia AQR113C
Switch Qualcomm Atheros QCA8075
USB 1x 3.1 Gen2
Serial TTL 115200, 8N1, 3.3V
PSU 19VDC 2.1A


You only need one of the available sysupgrade images. The other available images are needed for special purposes only.

Other images (factory, initramfs)


Currently (state of 2024) OpenWrt officially does not support the integrated FAN, the integrated LED.

  • LED: PR 15504
  • FAN: PR 14210
  • 5G 160MHz channel width is not supported officially. There is hack available. For those doing their own builds.

:!: The device can really run hot due to the disabled fan leading to throttling and instabilities. Esp. if an USB device is connected. You be advised to either deploy an active cooler directed to the device itself or making your own build integrating the patch referenced above for proper cooling. To the state of 2024 this FAN patch is not working reliable. But there are others (simpler, script based) solutions available (which could disappear/change over time) e. g.: by asvio, by ddimension, by psychowood, by pwned-pixel. There are more available just ask/look within the Forum Support Thread

To install OpenWrt on this device Root/SSH access is required. You can gain Root/SSH access with the following process using a terminal application. For Windows the most known is putty. For Linux/MAC OS choose any you want resp. its default terminal application.

  1. Disconnect the WAN cable of the router. Do not plug in back the WAN cable during the whole process!
  2. Reset the device to factory defaults by pushing and holding the reset button for ~15 seconds immediately after turning it on. The LED should light up orange.
  3. After ~5-10 minutes, when the LED is constant dark blue, connect your computer to one of the yellow LAN ports and wait for the connection to be established.
  4. Do not setup the router yet! Access the device via Telnet using address: 192.168.123.1 / port 23. On the prompt (NBG7815 login) login with username: root / password: nbg7815@2019 E. g. On a Linux Terminal: telnet 192.168.123.1 -p 23 using the password nbg7815@2019
  5. Enable permanent Root/SSH access for this device by copy and paste the script lines from below. It will prevent a root password change which happens after finishing the setup and enable dropbear/SSH.
  6. Reboot the device.
  7. Check if SSH access is working by using address: 192.168.123.1 / port: 22 / username: root / password: OpenWrt E. g. On a Linux Terminal: ssh -oStrictHostKeyChecking=no -oUserKnownHostsFile=/dev/null root@192.168.123.1 -p 22 using the password OpenWrt

Enable Root/SSH access

awk '/ckNowChangeDefaultCg/{f=0} f{$0="#" $0} /#dropbear/{f=1} 1' /rom/etc/init.d/preboot > /etc/init.d/preboot

echo -e 'OpenWrt\nOpenWrt' | passwd root
cp /etc/shadow /etc/shadow.bak

sed -i '/exit 0/i \
 \
uci set dropbear.setting.enable=1 \
uci commit dropbear \
uci set network.general.auto_ip_change=0 \
uci commit network \
/etc/init.d/dropbear enable \
/etc/init.d/dropbear restart \
chmod +w /etc/shadow \
cp /etc/shadow.bak /etc/shadow \
chmod -w /etc/shadow \
 \
 \' /etc/rc.local

chmod -w /etc/init.d/preboot
chmod -w /etc/config/dropbear
chmod -w /etc/rc.local
chmod -w /etc/shadow


Before you modify the device it is always a good idea to make a backup of the flash drive(s) installed. The generic process is described here.
We have one 8MB SPI NOR flash chip and one 4GB emmc flash chip. For both you can use dd. The partition layout of both chips is described here.
You can spare out the last two big partitions on the emmc chip if you want. They are not important. Transfer the files either via USB or ssh/scp.

:!: Do not power off the device during the process!

  1. Login as root via SSH.
  2. Change to directory /tmp/ApplicationData.
  3. Get the OpenWrt Firmware onto your router by either a) or b):
    a) The device to has internet access for downloading the OpenWrt firmware file to the device using wget.
    b) Download the OpenWrt firmware to your computer and move the file to a FAT or NTFS formatted USB drive. Connect the USB drive to your router and mount the USB device. Copy the file to /tmp/ApplicationData.
  4. Extract the firmware file.
  5. Determine the bootconfig of the device and flash OpenWrt to the currently not active kernel and rootfs partitions.
  6. Mark the partitions to boot OpenWrt.
  7. Reboot the device.

Semi-automatic (Step 2-7)

cd /tmp/ApplicationData
wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin https://downloads.openwrt.org/snapshots/targets/qualcommax/ipq807x/openwrt-qualcommax-ipq807x-zyxel_nbg7815-squashfs-sysupgrade.bin
wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh
sh flash_to_openwrt.sh

Step 2-6

# Author: Karol Przybylski <itor@o2.pl>
# https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh

# Step 2
cd /tmp/ApplicationData

# Step 3
wget -O zyxel_nbg7815-squashfs-sysupgrade.bin https://downloads.openwrt.org/snapshots/targets/qualcommax/ipq807x/openwrt-qualcommax-ipq807x-zyxel_nbg7815-squashfs-sysupgrade.bin
if [ ! -f "/tmp/ApplicationData/zyxel_nbg7815-squashfs-sysupgrade.bin" ]; then
     echo "Cannot find image zyxel_nbg7815-squashfs-sysupgrade.bin"
     exit 1
fi

# Step 4
tar xvf zyxel_nbg7815-squashfs-sysupgrade.bin

# Step 5
primaryboot_hlos=$(cat /proc/boot_info/0:HLOS/primaryboot)
if [ $primaryboot_hlos -eq 0 ]; then
     dd if=/dev/zero of=/dev/mmcblk0p7
     dd if=/tmp/ApplicationData/sysupgrade-zyxel_nbg7815/kernel of=/dev/mmcblk0p7
     echo 1 > /proc/boot_info/0:HLOS/primaryboot
else
     dd if=/dev/zero of=/dev/mmcblk0p3
     dd if=/tmp/ApplicationData/sysupgrade-zyxel_nbg7815/kernel of=/dev/mmcblk0p3
     echo 0 > /proc/boot_info/0:HLOS/primaryboot
fi

primaryboot_rootfs=$(cat /proc/boot_info/rootfs/primaryboot)
if [ $primaryboot_rootfs -eq 0 ]; then
     dd if=/dev/zero of=/dev/mmcblk0p8
     dd if=/tmp/ApplicationData/sysupgrade-zyxel_nbg7815/root of=/dev/mmcblk0p8
     echo 1 > /proc/boot_info/rootfs/primaryboot
else
     dd if=/dev/zero of=/dev/mmcblk0p4
     dd if=/tmp/ApplicationData/sysupgrade-zyxel_nbg7815/root of=/dev/mmcblk0p4
     echo 0 > /proc/boot_info/rootfs/primaryboot
fi

# Step 6
mkdir /tmp/ApplicationData/boot
cat /proc/boot_info/getbinary_bootconfig > /tmp/ApplicationData/boot/bootconfig_new.bin
echo 1 > /proc/mtd_writeable
dd if=/tmp/ApplicationData/boot/bootconfig_new.bin 2>/dev/null | mtd -e "/dev/mtd2" write - "/dev/mtd2" 2>/dev/null
dd if=/tmp/ApplicationData/boot/bootconfig_new.bin 2>/dev/null | mtd -e "/dev/mtd3" write - "/dev/mtd3" 2>/dev/null
echo 0 > /proc/mtd_writeable
sync

:!: For reference: initial commit nbg7815

OpenWrt is currently not using the dual partition layout writing the opposite/not active kernel/rootfs partitions during upgrade. So we can easy go back to OEM firmware by just setting the active kernel and rootfs partitions Back to OEM firmware (1). In case this changes in future or you have flashed the other partitions as well you can flash the OEM firmware with proper rootfs and kernel image too Back to OEM firmware (2). Another option would be using the TFTP flash OEM firmware process from section Debricking.

Be carefull with this process. :!: Do not power off the device during the process!

  1. Login via SSH to the router.
  2. To use this method it is required to install kmod-mtd-rw first: opkg update && opkg install kmod-mtd-rw.
  3. Change directory to /tmp.
  4. Copy & paste the code from script Step 4 below.
  5. Execute the script with sh change_boot_partition.sh.
  6. Reboot the device.
  7. After reboot force a reflash of OEM firmware via WebGui using one of the provided OEM firmware files to purge OpenWrt entirely.

Step 4

cat <<'EOF' > /tmp/change_boot_partition.sh
# Script to changing active boot partitions 
# Author: Karol Przybylski <itor@o2.pl>
# Orginal script: https://github.com/itorK/nbg7815_tools/blob/main/change_boot_partition.sh // It lacks the insmod mtd-rw i_want_a_brick=1

openwrt_type=$(cat /etc/openwrt_release|grep DISTRIB_TARGET|cut -f 2 -d "'")

if [ ${openwrt_type} == "ipq807x/generic" ]; then
  echo "OpenWrt release"
  boot_part=$(hexdump -e '1/1 "%01x|"' -n 1 -s 168 -C /dev/mtd2|cut -f 1 -d "|"|head -n1)

  dd if=/dev/mtd2 of=boot.bin bs=336 count=1

  if [ ${boot_part} -eq 0 ]; then
    printf '\x01' | dd of=boot.bin bs=1 seek=168 count=1 conv=notrunc
  else
    printf '\x00' | dd of=boot.bin bs=1 seek=168 count=1 conv=notrunc

  fi
  insmod mtd-rw i_want_a_brick=1
  mtd write boot.bin /dev/mtd2
  mtd write boot.bin /dev/mtd3
fi

if [ ${openwrt_type} == "ipq/ipq807x_64" ]; then
  echo "Original Zyxel Firmware"
  primaryboot_hlos=$(cat /proc/boot_info/0:HLOS/primaryboot)
  if [ $primaryboot_hlos -eq 0 ]; then
       echo 1 > /proc/boot_info/0:HLOS/primaryboot
  else
       echo 0 > /proc/boot_info/0:HLOS/primaryboot
  fi
  
  mkdir /tmp/ApplicationData/boot
  cat /proc/boot_info/getbinary_bootconfig > /tmp/ApplicationData/boot/bootconfig_new.bin
  echo 1 > /proc/mtd_writeable
  dd if=/tmp/ApplicationData/boot/bootconfig_new.bin 2>/dev/null | mtd -e "/dev/mtd2" write - "/dev/mtd2" 2>/dev/null
  dd if=/tmp/ApplicationData/boot/bootconfig_new.bin 2>/dev/null | mtd -e "/dev/mtd3" write - "/dev/mtd3" 2>/dev/null
  echo 0 > /proc/mtd_writeable
  sync
fi
EOF


:!: Be carefull with this process. Make sure you write the correct images to the correct partitions! Do not power off the device during the process!

  1. Download OEM firmware: see below
  2. Extract rootfs and kernel. Already extracted v8: kernel, rootfs
  3. Login via SSH to the router.
  4. To use this method it is required to install kmod-mtd-rw first: opkg update && opkg install kmod-mtd-rw
  5. Copy the files to the router to /tmp (e. g. using scp or an usb drive). Rename them to kernel resp. rootfs.
  6. Flash the kernel and rootfs to the currently not active partitions. Copy & paste the code from and execute the script with sh flash_kernel_rootfs.sh..
  7. Copy & paste the code from script Step 4 from Back to OEM firmware (1) and execute the script with sh change_boot_partition.sh.
  8. Reboot the device.
  9. After reboot force a reflash of OEM firmware via WebGui using one of the provided OEM firmware files to purge OpenWrt entirely.

Step 6

cat <<'EOF' > /tmp/flash_kernel_rootfs.sh
# check files

if [ ! -f "/tmp/rootfs" ]; then
     echo "rootfs image"
     exit 1
fi

if [ ! -f "/tmp/kernel" ]; then
     echo "kernel image"
     exit 1
fi

# get bootconfig

mtd_part=$(grep -i "\"0:bootconfig"\" /proc/mtd | awk -F: '{print $1}')
bootconfig=$(hexdump -v -e '1/1 "%01x|"' -n 1 -s 168 -C /dev/"$mtd_part" | cut -f 1 -d "|" | head -n1)

# write rootfs and kernel; mmcblk0p3=0/mmcblk0p4=0 mmcblk0p7=1/mmcblk0p8=1

if [ "${bootconfig}" -eq 1 ]; then
	dd if=/dev/zero of=/dev/mmcblk0p7
	dd if=/tmp/kernel of=/dev/mmcblk0p7
	dd if=/dev/zero of=/dev/mmcblk0p8
	dd if=/tmp/root of=/dev/mmcblk0p8
	sync
fi
if [ "${bootconfig}" -eq 0 ]; then
	dd if=/dev/zero of=/dev/mmcblk0p3
	dd if=/tmp/kernel of=/dev/mmcblk0p3
	dd if=/dev/zero of=/dev/mmcblk0p4
	dd if=/tmp/root of=/dev/mmcblk0p4
	sync
fi
EOF


There is no official publicly available ressource to download the firmware files for this cloud managed router. You can retrieve the firmware file by forcing a firmware upgrade and catching the temporary valid random cloudflare link by yourself (this is limited to the latest firmware only). Firmware files version 6-8 were uploaded to mega.nz:

Firmware sha256sum
V1.00(ABSK.8)C0.bin 1213e94cab334a9317ea405d95817255ba8970c3d2cd0fa4f16b92847ff8906c
V1.00(ABSK.7)C0.bin 3a6cd0a4a15fa88bfe4e05d77e562ccd6dfb9bc61994d411155d94710192a884
V1.00(ABSK.6)C0.bin 96e1e992552883e2a720e443f0ee5d31ba9b12bdd231786daed7d8425483e0f4

To get the rootfs and kernel image you have to extract them from the firmware file: rootfs=openwrt-ipq-ipq807x_64-squashfs-root.img, kernel=openwrt-ipq-ipq807x_64-qcom-ipq807x-zyxel-fit-uImage.itb.padded. To do so you would need a Linux machine with u-boot tools installed using dumpimage. Extracted rootfs and kernel for v8:

Firmware sha256sum
kernel_v8 9661a36422f357b3072ff5d1dd4e43c89410d8dd2267b343ca2e7f2cc608f6d3
rootfs_v8 cff590a82bb30ddced01e1d6514083519471aa4ca36e99a22d6fa74824075398


In case you've lost the access to your device e. g. due to wrong configuration you can try the failsafe mode, a factory reset or a tftp boot/flash to recover your device:

Failsafe mode and factory reset procedures: → failsafe_and_factory_reset

In case neither the failsafe mode nor a factory reset does bring back a working unit you can try to recover your device by the following steps:

  1. Connect to the device via serial connection using a terminal application e. g. putty and an USB to TTL/USB to Serial adapter.
  2. TFTP boot OpenWrt to either reinstall or fix a broken installation | TFTP flash OEM firmware to purge OpenWrt.


  1. Remove the two rubber crosses from the device' bottom side.
  2. Unscrew the two screws appearing after step 1.
  3. Remove the socket.
  4. After step 3. another four screws appear. Remove them as well.
  5. Around the device' case there are eleven clips* inside (two on each side, four in front and three in back) tying the upper shell with the bottom side.
  6. Keep the device with bottom side up and pry it up carefully around the case to remove the bottom side. Start at the side where the connectors are lead out.

*) You will likely break some of them. Especially those on the left or right side. The clips at the front's case are very tight clipped because of the case' shape and the fact that there are four of them.

nbg7815_open_1.jpg nbg7815_open_2.jpg nbg7815_open_3.jpg

General information about the serial port and its usage:

Serial Port connectors of this specific device:

Serial connection parameters TTL 115200, 8N1, 3.3V

:!: Connect RX, TX, GND cable to your USB to TTL/USB to Serial adapter only!

  1. Connect the USB-to-serial adapter to the router and PC. Open up a serial console program.
  2. Reboot the device and interrupt autoboot by pressing any key. You will end up with a shell prompt: NBG7815>

    Zyxel zloader v1.0.0 (2020-01-06 - 08:24)
    
    Multiboot clinent version: 2.0
    ipq807x_eth_halt: done
    eth0 PHY0 Down Speed :10 Half duplex
    eth0 PHY1 Down Speed :10 Half duplex
    eth0 PHY2 Down Speed :10 Half duplex
    eth0 PHY3 Down Speed :10 Half duplex
    eth0 PHY4 Down Speed :10 Half duplex
    10M speed not supported
    ipq807x_eth_halt: done
    Ethernet interface failed to initialized!
    
    **Hit any key to stop autoboot:  3**
    
    NBG7815>
  3. To get access to the bootloader you first need a seed/passcode. You will obtain it by typing ATSE NBG7815 into the console prompt:

    NBG7815> ATSE NBG7815
    NBG7815> 013D72FF0710

    013D72FF0710 is the resulting seed/passcode :!: This seed/passcode is always different for each boot → You have to do the same procedure on every reboot to access u-boot!

  4. Generate the password:

    :!: Do not enter the code below it into the current shell! We have to open a new terminal application. We have distinguish here between Windows and Linux users!

    Linux: Copy and paste the code from below into a newly opened terminal. First use calc script and then generate password executing the script using the seed/passcode generated in section 3.

    Windows you can use ZynPass to calculate the password.

    calc script

    cat <<'EOF' > tool.sh
    ror32() {
      echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) ))
    }
    v="0x$1"
    a="0x${v:2:6}"
    b=$(( $a + 0x10F0A563))
    c=$(( 0x${v:12:14} & 7 ))
    p=$(( $(ror32 $b $c) ^ $a ))
    printf "ATEN 1,%X\n" $p
    EOF

    password

    sh tool.sh 013D72FF0710

    The resulting password looks like: ATEN 1,10F0A563

  5. Put the output from paragraph 4. in the terminal and press enter:

    NBG7815> ATEN 1,10F0A563
  6. Now Enter ATGU for full u-boot access. You will end up with a new prompt: ZYXEL#

    NBG7815> ATGU
    
    ZYXEL#


  1. Download OpenWrt Firmware/Other images (factory, initramfs) choosing an itb firmware file.
  2. Setup your PC/Workstation assigning the static IP 192.168.1.99.
  3. Install and configure TFTP server. Your router's u-boot environment is acting as client. → tftpserver. Put the firmware file downloaded in the tftp download directory and make sure the firewall is turned off or configured properly (port 69/udp has to be open).
  4. Connect your PC/Workstation via LAN cable to the router.
  5. Power up your router and get access to u-boot as describe above. Step 1-6 reaching ZYXEL# prompt.
  6. Enter tftpboot and the name of firmware file e. g. openwrt-qualcommax-ipq807x-zyxel_nbg7815-initramfs-uImage.itb:
    ZYXEL# tftpboot openwrt-qualcommax-ipq807x-zyxel_nbg7815-initramfs-uImage.itb
  7. After the file is uploaded (this takes a while) you may proceed with entering bootm into the shell:
    ZYXEL# bootm
  8. If OpenWrt is up you can try to fix your issues. E. g. fixing wrong config preventing booting the device, reinstall OpenWrt using sysupgrade, reinstall OpenWrt as described here or install OEM firmware like here.


  1. Download the OEM firmware.
  2. Setup your PC/Workstation assigning the static IP 192.168.1.99.
  3. Install and configure TFTP server. Your router's u-boot environment is acting as client. → tftpserver. Put the firmware file downloaded in the tftp download directory and make sure the firewall is turned off or configured properly (port 69/udp has to be open).
  4. Connect your PC/Workstation via LAN cable to the router.
  5. Power up your router and get access to u-boot as describe above. Step 1-2 is enough (no need unlock).
  6. Enter ATUR and the name of the downloaded firmware file e. g. ATUR V1.00(ABSK.8)C0.bin:
    NBG7815> ATUR V1.00(ABSK.8)C0.bin

    :!: Do not power off the device during the process!

Zyxel NBG7815 (Armor G5) PCB (1) Zyxel NBG7815 (Armor G5) PCB (2)

spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
m25p80 spi32766.0: found w25q64dw, expected n25q128a11
m25p80 spi32766.0: w25q64dw (8192 Kbytes)
22 ofpart partitions found on MTD device spi32766.0
Creating 22 MTD partitions on "spi32766.0":

0x000000000000-0x000000050000 : "0:SBL1"
0x000000050000-0x000000060000 : "0:MIBIB"
0x000000060000-0x000000080000 : "0:BOOTCONFIG"
0x000000080000-0x0000000a0000 : "0:BOOTCONFIG1"
0x0000000a0000-0x000000220000 : "0:QSEE"
0x000000220000-0x0000003a0000 : "0:QSEE_1"
0x0000003a0000-0x0000003b0000 : "0:DEVCFG"
0x0000003b0000-0x0000003c0000 : "0:DEVCFG_1"
0x0000003c0000-0x0000003d0000 : "0:APDP"
0x0000003d0000-0x0000003e0000 : "0:APDP_1"
0x0000003e0000-0x000000420000 : "0:RPM"
0x000000420000-0x000000460000 : "0:RPM_1"
0x000000460000-0x000000470000 : "0:CDT"
0x000000470000-0x000000480000 : "0:CDT_1"
0x000000480000-0x000000540000 : "0:APPSBL"
0x000000540000-0x000000600000 : "0:APPSBL_1"
0x000000600000-0x000000610000 : "0:APPSBLENV"
0x000000610000-0x000000650000 : "0:ART"
0x000000650000-0x0000006d0000 : "0:ETHPHYFW"
0x0000006d0000-0x0000006e0000 : "0:CRT"
0x0000006e0000-0x0000006f0000 : "DUAL_FLAG"
0x0000006f0000-0x000000800000 : "RESERVED"

cat /proc/mtd

dev:    size   erasesize  name
mtd0: 00050000 00010000 "0:sbl1"
mtd1: 00010000 00010000 "0:mibib"
mtd2: 00020000 00010000 "0:bootconfig"
mtd3: 00020000 00010000 "0:bootconfig1"
mtd4: 00180000 00010000 "0:qsee"
mtd5: 00180000 00010000 "0:qsee_1"
mtd6: 00010000 00010000 "0:devcfg"
mtd7: 00010000 00010000 "0:devcfg_1"
mtd8: 00010000 00010000 "0:apdp"
mtd9: 00010000 00010000 "0:apdp_1"
mtd10: 00040000 00010000 "0:rpm"
mtd11: 00040000 00010000 "0:rpm_1"
mtd12: 00010000 00010000 "0:cdt"
mtd13: 00010000 00010000 "0:cdt_1"
mtd14: 000c0000 00010000 "0:appsbl"
mtd15: 000c0000 00010000 "0:appsbl_1"
mtd16: 00010000 00010000 "0:appsblenv"
mtd17: 00040000 00010000 "0:art"
mtd18: 00080000 00010000 "0:ethphyfw"
mtd19: 00010000 00010000 "0:crt"
mtd20: 00010000 00010000 "dual_flag"
mtd21: 00110000 00010000 "reserved"
mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
Waiting for root device PARTUUID=a0bb3852-36cc-ac69-a1a2-6bd39ff56f0a...
mmc0: MAN_BKOPS_EN bit is not set
mmc0: new high speed MMC card at address 0001
mmcblk0: mmc0:0001 M62704 3.53 GiB
mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB
GPT: device [179:4] (rootfs) set to be root filesystem
mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11

sgdisk -p /dev/mmcblk0

Disk /dev/mmcblk0: 7405568 sectors, 3.5 GiB
Sector size (logical/physical): 512/512 bytes
Disk identifier (GUID): 98101B32-BBE2-4BF2-A06E-2BB33D000C20
Partition table holds up to 12 entries
Main partition table begins at sector 2 and ends at sector 4
First usable sector is 34, last usable sector is 7405534
Partitions will be aligned on 2-sector boundaries
Total free space is 282557 sectors (138.0 MiB)

Number  Start (sector)    End (sector)  Size       Code  Name
   1              34           16417   8.0 MiB     FFFF  rootfs_data
   2           16418           18465   1024.0 KiB  FFFF  header
   3           18466           30753   6.0 MiB     FFFF  0:HLOS
   4           30754          153633   60.0 MiB    FFFF  rootfs
   5          153634          161825   4.0 MiB     FFFF  0:WIFIFW
   6          161826          163873   1024.0 KiB  FFFF  header_1
   7          163874          176161   6.0 MiB     FFFF  0:HLOS_1
   8          176162          299041   60.0 MiB    FFFF  rootfs_1
   9          299042          307233   4.0 MiB     FFFF  0:WIFIFW_1
  10          307234         1355809   512.0 MiB   FFFF  nbg
  11         1355810         7122977   2.8 GiB     FFFF  appdata



Format: Log Type - Time(microsec) - Message - Optional Info
Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00147
S - IMAGE_VARIANT_STRING=HAABANAZA
S - OEM_IMAGE_VERSION_STRING=CRM
S - Boot Config, 0x000002e1
B -       203 - PBL, Start
B -      2737 - bootable_media_detect_entry, Start
B -      2885 - bootable_media_detect_success, Start
B -      2889 - elf_loader_entry, Start
B -     11481 - auth_hash_seg_entry, Start
B -     11721 - auth_hash_seg_exit, Start
B -    252687 - elf_segs_hash_verify_entry, Start
B -    313206 - PBL, End
B -    340502 - SBL1, Start
B -    394914 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4
B -    401685 - pm_device_init, Start
B -    528626 - PM_SET_VAL:Skip
D -    126239 - pm_device_init, Delta
B -    530913 - pm_driver_init, Start
D -      5368 - pm_driver_init, Delta
B -    537349 - clock_init, Start
D -      2135 - clock_init, Delta
B -    541405 - boot_flash_init, Start
D -     16470 - boot_flash_init, Delta
B -    561627 - boot_config_data_table_init, Start
D -      1006 - boot_config_data_table_init, Delta - (575 Bytes)
B -    569282 - Boot Setting :  0x00000618
B -    573003 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:241
B -    580110 - sbl1_ddr_set_params, Start
B -    583922 - CPR configuration: 0x30c
B -    587308 - cpr_init, Start
B -    590175 - Rail:0 Mode: 5 Voltage: 824000
B -    595299 - CL CPR settled at 776000mV
B -    598105 - Rail:1 Mode: 5 Voltage: 888000
B -    602405 - Rail:1 Mode: 7 Voltage: 928000
D -     16439 - cpr_init, Delta
B -    609176 - Pre_DDR_clock_init, Start
B -    613202 - Pre_DDR_clock_init, End
B -    616588 - DDR Type : PCDDR3
B -    622352 - do ddr sanity test, Start
D -      1067 - do ddr sanity test, Delta
B -    627080 - DDR: Start of HAL DDR Boot Training
B -    631838 - DDR: End of HAL DDR Boot Training
B -    637511 - DDR: Checksum to be stored on flash is 1873222707
B -    647911 - Image Load, Start
D -    335866 - QSEE Image Loaded, Delta - (1373936 Bytes)
B -    983869 - Image Load, Start
D -        61 - SEC Image Loaded, Delta - (0 Bytes)
B -    991524 - Image Load, Start
D -      9791 - DEVCFG Image Loaded, Delta - (26004 Bytes)
B -   1001406 - Image Load, Start
D -     30897 - RPM Image Loaded, Delta - (105964 Bytes)
B -   1032394 - Image Load, Start
D -    144631 - APPSBL Image Loaded, Delta - (588472 Bytes)
B -   1177147 - QSEE Execution, Start
D -        61 - QSEE Execution, Delta
B -   1182973 - USB D+ check, Start
D -         0 - USB D+ check, Delta
B -   1189347 - SBL1, End
D -    851163 - SBL1, Delta
S - Flash Throughput, 4428 KB/s  (2095623 Bytes,  473169 us)
S - DDR Frequency, 466 MHz
S - Core 0 Frequency, 1651 MHz
U-Boot 2016.01 (Jan 06 2020 - 08:24:12 +0000)

DRAM:  smem ram ptable found: ver: 1 len: 4
1 GiB
NAND:  Not an ONFI device
ONFI probe failed
ID = ffffffff
Vendor = ff
Device = ff
qpic_nand: unknown NAND device manufacturer: ff device: ff
U-Boot BUG at drivers/mtd/mtdcore.c:420!
SPI_ADDR_LEN=3
SF: Detected W25Q64DW with page size 256 Bytes, erase size 4 KiB, total 8 MiB
ipq_spi: page_size: 0x100, sector_size: 0x1000, size: 0x800000
8 MiB
MMC:   <NULL>: 0
In:    serial@78B3000
Out:   serial@78B3000
Err:   serial@78B3000
machid: 80100f1
Setting bus to 0
Valid chip addresses: 40
Net:   MAC0 addr:bc:cf:4f:ff:1b:a0
PHY ID1: 0x4d
PHY ID2: 0xd0b1
PHY ID1: 0x4d
PHY ID2: 0xd101
SPI_ADDR_LEN=3
SF: Detected W25Q64DW with page size 256 Bytes, erase size 4 KiB, total 8 MiB
device 0 offset 0x650000, size 0x80000
SF: 524288 bytes @ 0x650000 Read: OK
CRC check good on phy fw file (0x4B33)
PHYFW:Loading IRAM...........done.
PHYFW:Loading DRAM..............done.
phy fw image load good CRC-16 matches (0x6FFA)
PHY ID1: 0x31c3
PHY ID2: 0x1c12
EDMA ver 1 hw init
Num rings - TxDesc:1 (0-0) TxCmpl:1 (7-7)
RxDesc:1 (15-15) RxFill:1 (7-7)
ipq807x_edma_alloc_rings: successfull
ipq807x_edma_setup_ring_resources: successfull
ipq807x_edma_configure_rings: successfull
ipq807x_edma_hw_init: successfull
eth0
SPI_ADDR_LEN=3
SF: Detected W25Q64DW with page size 256 Bytes, erase size 4 KiB, total 8 MiB
device 0 offset 0x530000, size 0x10000
SF: 65536 bytes @ 0x530000 Read: OK
## Booting kernel from Legacy Image at 44000000 ...
   Image Name:   Zyxel zloader
   Image Type:   ARM U-Boot Standalone Program (gzip compressed)
   Data Size:    15340 Bytes = 15 KiB
   Load Address: 5f000000
   Entry Point:  5f00000c
   Verifying Checksum ... OK
   Uncompressing Standalone Program ... OK
Zyxel zloader v1.0.0 (2020-01-06 - 08:24)

Multiboot clinent version: 2.0
ipq807x_eth_halt: done
eth0 PHY0 up Speed :1000 Full duplex
eth0 PHY1 Down Speed :10 Half duplex
eth0 PHY2 Down Speed :10 Half duplex
eth0 PHY3 up Speed :1000 Full duplex
eth0 PHY4 up Speed :1000 Full duplex
10M speed not supported
ipq807x_eth_init: done

Hit any key to stop autoboot:  0ipq807x_eth_halt: done

*** Booting from system 1 ***

MMC read: dev # 0, block # 163874, count 12288 ... 12288 blocks read: OK
## Loading kernel from FIT Image at 44000000 ...
   Using 'config@nbg7815' configuration
   Trying 'kernel@1' kernel subimage
     Description:  ARM64 OpenWrt Linux-4.4.60
     Type:         Kernel Image
     Compression:  gzip compressed
     Data Start:   0x440000e8
     Data Size:    4084783 Bytes = 3.9 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x41080000
     Entry Point:  0x41080000
     Hash algo:    crc32
     Hash value:   6f0d3aaa
     Hash algo:    sha1
     Hash value:   00e6f72c77acd5fed3999b0148c5a524802e1357
   Verifying Hash Integrity ... crc32+ sha1+ OK
## Loading fdt from FIT Image at 44000000 ...
   Using 'config@nbg7815' configuration
   Trying 'fdt@nbg7815' fdt subimage
     Description:  ARM64 OpenWrt qcom-ipq807x-zyxel device tree blob
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0x44439584
     Data Size:    80584 Bytes = 78.7 KiB
     Architecture: AArch64
     Hash algo:    crc32
     Hash value:   689818c1
     Hash algo:    sha1
     Hash value:   6878282b432ec6f7c84ff68feb774c222850c457
   Verifying Hash Integrity ... crc32+ sha1+ OK
   Booting using the fdt blob at 0x44439584
   Uncompressing Kernel Image ... OK
   Loading Device Tree to 4a3e9000, end 4a3ffac7 ... OK
Using machid 0x80100f1 from environment
[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034]
[    0.000000] Linux version 6.6.52 (NBG7815@R51600) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 13.3.0 r27578+1-23ac1ad951) 13.3.0, GNU ld (GNU Binutils) 2.42) #0 SMP Wed Sep 25 06:57:27 2024
[    0.000000] Machine model: Zyxel NBG7815
[    0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 KiB) nomap non-reusable nss@40000000
[    0.000000] OF: reserved mem: 0x000000004a400000..0x000000004a5fffff (2048 KiB) nomap non-reusable tzapp@4a400000
[    0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fffff (4096 KiB) nomap non-reusable bootloader@4a600000
[    0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafffff (1024 KiB) nomap non-reusable sbl@4aa00000
[    0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004abfffff (1024 KiB) nomap non-reusable smem@4ab00000
[    0.000000] OF: reserved mem: 0x000000004ac00000..0x000000004affffff (4096 KiB) nomap non-reusable memory@4ac00000
[    0.000000] OF: reserved mem: 0x000000004b000000..0x0000000050efffff (97280 KiB) nomap non-reusable wcnss@4b000000
[    0.000000] OF: reserved mem: 0x0000000050f00000..0x0000000050ffffff (1024 KiB) nomap non-reusable q6_etr_dump@50f00000
[    0.000000] OF: reserved mem: 0x0000000051000000..0x00000000510fffff (1024 KiB) nomap non-reusable m3_dump@51000000
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000040000000-0x000000007fffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   empty
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x0000000040ffffff]
[    0.000000]   node   0: [mem 0x0000000041000000-0x000000004a3fffff]
[    0.000000]   node   0: [mem 0x000000004a400000-0x00000000510fffff]
[    0.000000]   node   0: [mem 0x0000000051100000-0x000000007fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000007fffffff]
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.0 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: MIGRATE_INFO_TYPE not supported.
[    0.000000] psci: SMC Calling Convention v1.0
[    0.000000] psci: OSI mode supported.
[    0.000000] psci: [Firmware Bug]: failed to set PC mode: -1
[    0.000000] percpu: Embedded 18 pages/cpu s35240 r8192 d30296 u73728
[    0.000000] pcpu-alloc: s35240 r8192 d30296 u73728 alloc=18*4096
[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] alternatives: applying boot alternatives
[    0.000000] Kernel command line: ttyMSM0,115200n8 root=PARTUUID=1991ff67-765c-8ba9-2885-4ccd1351bfd3 rootwait
[    0.000000] Unknown kernel command line parameters "ttyMSM0,115200n8", will be passed to user space.
[    0.000000] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.000000] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 258048
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: SWIOTLB bounce buffer size adjusted to 1MB
[    0.000000] software IO TLB: area num 4.
[    0.000000] software IO TLB: mapped [mem 0x000000007eb00000-0x000000007ec00000] (1MB)
[    0.000000] Memory: 885584K/1048576K available (8256K kernel code, 892K rwdata, 2504K rodata, 1536K init, 276K bss, 162992K reserved, 0K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] Root IRQ handler: gic_handle_irq
[    0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479]
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[    0.000001] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[    0.000109] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[    0.000122] pid_max: default: 32768 minimum: 301
[    0.005263] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.005277] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes, linear)
[    0.009608] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[    0.009840] rcu: Hierarchical SRCU implementation.
[    0.009845] rcu:     Max phase no-delay instances is 1000.
[    0.010763] smp: Bringing up secondary CPUs ...
[    0.011444] Detected VIPT I-cache on CPU1
[    0.011550] CPU1: Booted secondary processor 0x0000000001 [0x410fd034]
[    0.012237] Detected VIPT I-cache on CPU2
[    0.012309] CPU2: Booted secondary processor 0x0000000002 [0x410fd034]
[    0.012979] Detected VIPT I-cache on CPU3
[    0.013045] CPU3: Booted secondary processor 0x0000000003 [0x410fd034]
[    0.013115] smp: Brought up 1 node, 4 CPUs
[    0.013124] SMP: Total of 4 processors activated.
[    0.013129] CPU features: detected: 32-bit EL0 Support
[    0.013134] CPU features: detected: CRC32 instructions
[    0.013204] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching
[    0.013211] CPU: All CPU(s) started at EL1
[    0.013214] alternatives: applying system-wide alternatives
[    0.023615] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.023642] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.025435] pinctrl core: initialized pinctrl subsystem
[    0.027205] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.027773] DMA: preallocated 128 KiB GFP_KERNEL pool for atomic allocations
[    0.027816] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.027850] DMA: preallocated 128 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.028235] thermal_sys: Registered thermal governor 'step_wise'
[    0.028293] cpuidle: using governor menu
[    0.028483] ASID allocator initialised with 65536 entries
[    0.085380] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[    0.087541] Modules: 29360 pages in range for non-PLT usage
[    0.087548] Modules: 520880 pages in range for PLT usage
[    0.092531] SCSI subsystem initialized
[    0.092726] usbcore: registered new interface driver usbfs
[    0.092760] usbcore: registered new interface driver hub
[    0.092823] usbcore: registered new device driver usb
[    0.093252] qcom_scm: convention: smc arm 64
[    0.094980] clocksource: Switched to clocksource arch_sys_counter
[    0.098803] NET: Registered PF_INET protocol family
[    0.098969] IP idents hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.101579] tcp_listen_portaddr_hash hash table entries: 512 (order: 1, 8192 bytes, linear)
[    0.101641] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.101658] TCP established hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.101744] TCP bind hash table entries: 8192 (order: 6, 262144 bytes, linear)
[    0.102019] TCP: Hash tables configured (established 8192 bind 8192)
[    0.102125] UDP hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.102164] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes, linear)
[    0.102612] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.102665] PCI: CLS 0 bytes, default 64
[    0.104346] workingset: timestamp_bits=46 max_order=18 bucket_order=0
[    0.104946] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.104954] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[    0.111672] qcom-qmp-usb-phy 58000.phy: supply vdda-phy not found, using dummy regulator
[    0.111843] qcom-qmp-usb-phy 58000.phy: supply vdda-pll not found, using dummy regulator
[    0.113368] qcom-qmp-usb-phy 78000.phy: supply vdda-phy not found, using dummy regulator
[    0.113511] qcom-qmp-usb-phy 78000.phy: supply vdda-pll not found, using dummy regulator
[    0.115301] qcom-qusb2-phy 59000.phy: supply vdd not found, using dummy regulator
[    0.115478] qcom-qusb2-phy 59000.phy: supply vdda-pll not found, using dummy regulator
[    0.115519] qcom-qusb2-phy 59000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[    0.115698] qcom-qusb2-phy 59000.phy: Registered Qcom-QUSB2 phy
[    0.115941] qcom-qusb2-phy 79000.phy: supply vdd not found, using dummy regulator
[    0.116058] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator
[    0.116116] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator
[    0.116315] qcom-qusb2-phy 79000.phy: Registered Qcom-QUSB2 phy
[    0.126923] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled
[    0.128027] msm_serial 78b1000.serial: msm_serial: detected port #1
[    0.128069] msm_serial 78b1000.serial: uartclk = 19200000
[    0.128400] 78b1000.serial: ttyMSM1 at MMIO 0x78b1000 (irq = 20, base_baud = 1200000) is a MSM
[    0.128861] msm_serial 78b3000.serial: msm_serial: detected port #0
[    0.128896] msm_serial 78b3000.serial: uartclk = 3686400
[    0.129200] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 21, base_baud = 230400) is a MSM
[    0.129231] msm_serial: console setup on port #0
[    0.129274] printk: console [ttyMSM0] enabled
[    0.974818] msm_serial: driver initialized
[    0.984110] loop: module loaded
[    0.985479] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[    0.987134] spi-nor spi0.0: w25q64dw (8192 Kbytes)
[    0.993718] 22 fixed-partitions partitions found on MTD device spi0.0
[    0.998434] Creating 22 MTD partitions on "spi0.0":
[    1.004470] 0x000000000000-0x000000050000 : "0:sbl1"
[    1.010681] 0x000000050000-0x000000060000 : "0:mibib"
[    1.014910] 0x000000060000-0x000000080000 : "0:bootconfig"
[    1.019848] 0x000000080000-0x0000000a0000 : "0:bootconfig1"
[    1.025227] 0x0000000a0000-0x000000220000 : "0:qsee"
[    1.030793] 0x000000220000-0x0000003a0000 : "0:qsee_1"
[    1.036102] 0x0000003a0000-0x0000003b0000 : "0:devcfg"
[    1.040784] 0x0000003b0000-0x0000003c0000 : "0:devcfg_1"
[    1.045969] 0x0000003c0000-0x0000003d0000 : "0:apdp"
[    1.051402] 0x0000003d0000-0x0000003e0000 : "0:apdp_1"
[    1.056400] 0x0000003e0000-0x000000420000 : "0:rpm"
[    1.061301] 0x000000420000-0x000000460000 : "0:rpm_1"
[    1.066094] 0x000000460000-0x000000470000 : "0:cdt"
[    1.071252] 0x000000470000-0x000000480000 : "0:cdt_1"
[    1.076022] 0x000000480000-0x000000540000 : "0:appsbl"
[    1.081192] 0x000000540000-0x000000600000 : "0:appsbl_1"
[    1.086238] 0x000000600000-0x000000610000 : "0:appsblenv"
[    1.091567] 0x000000610000-0x000000650000 : "0:art"
[    1.097091] 0x000000650000-0x0000006d0000 : "0:ethphyfw"
[    1.102003] 0x0000006d0000-0x0000006e0000 : "0:crt"
[    1.107270] 0x0000006e0000-0x0000006f0000 : "dual_flag"
[    1.111822] 0x0000006f0000-0x000000800000 : "reserved"
[    1.125622] spmi spmi-0: PMIC arbiter version v2 (0x20010000)
[    1.178716] i2c_dev: i2c /dev entries driver
[    1.186465] sdhci: Secure Digital Host Controller Interface driver
[    1.186507] sdhci: Copyright(c) Pierre Ossman
[    1.191541] sdhci-pltfm: SDHCI platform and OF driver helper
[    1.198157] remoteproc remoteproc0: releasing cd00000.q6v5_wcss
[    1.221409] NET: Registered PF_INET6 protocol family
[    1.222629] Segment Routing with IPv6
[    1.225535] In-situ OAM (IOAM) with IPv6
[    1.229069] NET: Registered PF_PACKET protocol family
[    1.232758] mmc0: SDHCI controller on 7824900.mmc [7824900.mmc] using ADMA 64-bit
[    1.233295] 8021q: 802.1Q VLAN Support v1.8
[    1.277063] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[    1.277387] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[    1.283192] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[    1.289828] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[    1.291654] mmc0: new HS200 MMC card at address 0001
[    1.297470] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[    1.305718] mmcblk0: mmc0:0001 M62704 3.53 GiB
[    1.310010] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[    1.320325]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11
[    1.323557] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      SVS: open-loop= 712000 uV
[    1.332040] mmcblk0boot0: mmc0:0001 M62704 2.00 MiB
[    1.335904] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      NOM: open-loop= 832000 uV
[    1.346722] mmcblk0boot1: mmc0:0001 M62704 2.00 MiB
[    1.350297] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused    TURBO: open-loop= 904000 uV
[    1.360855] mmcblk0rpmb: mmc0:0001 M62704 512 KiB, chardev (247:0)
[    1.364973] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused   STURBO: open-loop= 992000 uV
[    1.365038] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      SVS: quot[ 7]= 701, quot_offset[ 7]=   0
[    1.391019] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      NOM: quot[ 7]= 925, quot_offset[ 7]= 220
[    1.401869] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused    TURBO: quot[ 7]=1045, quot_offset[ 7]= 120
[    1.412806] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused   STURBO: quot[ 7]=1198, quot_offset[ 7]= 150
[    1.423980] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[    1.427213] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz
[    1.443562] remoteproc remoteproc0: cd00000.q6v5_wcss is available
[    1.452588] clk: Disabling unused clocks
[    1.460759] VFS: Mounted root (squashfs filesystem) readonly on device 179:4.
[    1.461242] Freeing unused kernel memory: 1536K
[    1.467033] Run /sbin/init as init process
[    1.471209]   with arguments:
[    1.471211]     /sbin/init
[    1.471212]     ttyMSM0,115200n8
[    1.471214]   with environment:
[    1.471216]     HOME=/
[    1.471217]     TERM=linux
[    1.557158] init: Console is alive
[    1.557272] init: - watchdog -
[    1.920210] kmodloader: loading kernel modules from /etc/modules-boot.d/*
[    1.932607] hwmon hwmon0: temp1_input not attached to any thermal zone
[    1.951844] gpio_button_hotplug: loading out-of-tree module taints kernel.
[    1.977696] ssdk_dt_parse_interrupt[941]:INFO:intr-gpio does not exist
[    2.037636] aquantia_phy_api_ops_init[1485]:INFO:qca probe aquantia phy driver succeeded!
[    3.915064] regi_init[2525]:INFO:Initializing HPPE Done!!
[    3.915191] regi_init[2574]:INFO:qca-ssdk module init succeeded!
[    3.921679] EDMA ver 1 hw init
[    3.925779] EDMA HW Reset completed succesfully
[    3.928423] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)
[    3.932818] RxDesc:1 (15-15) RxFill:1 (7-7)
[    3.938501] dp1: ppe offload disabled: 0 for macid 1
[    3.942194] dp1: Switch attached to macid 1 status: 0
[    4.145766] Qualcomm QCA8075 90000.mdio-1:00: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:00, irq=POLL)
[    4.146887] dp2: ppe offload disabled: 0 for macid 2
[    4.154660] dp2: Switch attached to macid 2 status: 0
[    4.235313] Qualcomm QCA8075 90000.mdio-1:01: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:01, irq=POLL)
[    4.236264] dp3: ppe offload disabled: 0 for macid 3
[    4.244207] dp3: Switch attached to macid 3 status: 0
[    4.325357] Qualcomm QCA8075 90000.mdio-1:02: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:02, irq=POLL)
[    4.326253] dp4: ppe offload disabled: 0 for macid 4
[    4.334252] dp4: Switch attached to macid 4 status: 0
[    4.425343] Qualcomm QCA8075 90000.mdio-1:03: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:03, irq=POLL)
[    4.426459] dp5: ppe offload disabled: 0 for macid 5
[    4.434239] dp5: Switch attached to macid 5 status: 0
[    4.537208] Qualcomm QCA8081 90000.mdio-1:1c: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:1c, irq=POLL)
[    4.538568] dp6-syn: ppe offload disabled: 0 for macid 6
[    4.546116] dp6-syn: Switch attached to macid 6 status: 0
[    4.560409] Aquantia AQR113C 90000.mdio-1:08: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:08, irq=POLL)
[    4.561372] **********************************************************
[    4.569321] * NSS Data Plane driver
[    4.575813] **********************************************************
[    4.595854] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    4.595904] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1
[    4.600375] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008002000010
[    4.607899] xhci-hcd xhci-hcd.1.auto: irq 42, io mem 0x08a00000
[    4.617282] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[    4.623071] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2
[    4.628637] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed
[    4.636562] hub 1-0:1.0: USB hub found
[    4.642788] hub 1-0:1.0: 1 port detected
[    4.646782] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.650946] hub 2-0:1.0: USB hub found
[    4.658862] hub 2-0:1.0: 1 port detected
[    4.662651] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[    4.666382] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 3
[    4.671722] xhci-hcd xhci-hcd.2.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000008002000010
[    4.679204] xhci-hcd xhci-hcd.2.auto: irq 43, io mem 0x08c00000
[    4.688641] xhci-hcd xhci-hcd.2.auto: xHCI Host Controller
[    4.694425] xhci-hcd xhci-hcd.2.auto: new USB bus registered, assigned bus number 4
[    4.699997] xhci-hcd xhci-hcd.2.auto: Host supports USB 3.0 SuperSpeed
[    4.707873] hub 3-0:1.0: USB hub found
[    4.714142] hub 3-0:1.0: 1 port detected
[    4.718134] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[    4.722442] hub 4-0:1.0: USB hub found
[    4.730040] hub 4-0:1.0: 1 port detected
[    4.735049] kmodloader: done loading kernel modules from /etc/modules-boot.d/*
[    4.743898] init: - preinit -
[    5.034985] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[    5.284576] hub 3-1:1.0: USB hub found
[    5.286279] hub 3-1:1.0: 4 ports detected
[    5.365219] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[    5.428212] hub 4-1:1.0: USB hub found
[    5.428620] hub 4-1:1.0: 4 ports detected
[    5.694974] usb 3-1.4: new high-speed USB device number 3 using xhci-hcd
[    5.945014] usb 4-1.2: new SuperSpeed USB device number 3 using xhci-hcd
[   11.644972] random: crng init done
[   13.772161] loop0: detected capacity change from 0 to 122880
[   13.815007] loop0: detected capacity change from 122880 to 107008
[   13.816157] mount_root: overlay filesystem in /dev/loop0 has not been formatted yet
[   14.211915] EXT4-fs (loop0): mounted filesystem b70c817e-2ac1-4ca7-8800-0c3dfeade3a2 r/w with ordered data mode. Quota mode: disabled.
[   14.212409] mount_root: overlay filesystem has not been fully initialized yet
[   14.223685] mount_root: switching to ext4 overlay
[   14.233358] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off.
[   14.236169] urandom-seed: Seed file not found (/etc/urandom.seed)
[   14.274921] procd: - early -
[   14.275089] procd: - watchdog -
[   14.815682] procd: - watchdog -
[   14.816299] procd: - ubus -
[   14.876443] procd: - init -
[   15.100327] kmodloader: loading kernel modules from /etc/modules.d/*
[   15.185051] hid: raw HID events driver (C) Jiri Kosina
[   15.194877] Bluetooth: Core ver 2.22
[   15.195103] NET: Registered PF_BLUETOOTH protocol family
[   15.197526] Bluetooth: HCI device and connection manager initialized
[   15.202837] Bluetooth: HCI socket layer initialized
[   15.209179] Bluetooth: L2CAP socket layer initialized
[   15.213772] Bluetooth: SCO socket layer initialized
[   15.220838] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[   15.223655] Bluetooth: BNEP filters: protocol multicast
[   15.229237] Bluetooth: BNEP socket layer initialized
[   15.232970] urngd: v1.0.2 started.
[   15.241697] usbcore: registered new interface driver btusb
[   15.242963] Loading modules backported from Linux version v6.9.9-0-g28fdf4518483
[   15.248138] Backport generated by backports.git v6.1.97-1-29-gf1d24a3683b2
[   15.256945] Bluetooth: HCI UART driver ver 2.3
[   15.262282] Bluetooth: HCI UART protocol H4 registered
[   15.266727] Bluetooth: HCI UART protocol BCSP registered
[   15.272614] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[   15.277328] Bluetooth: HIDP socket layer initialized
[   15.289691] NET: Registered PF_QIPCRTR protocol family
[   15.292071] Bluetooth: RFCOMM TTY layer initialized
[   15.293734] Bluetooth: RFCOMM socket layer initialized
[   15.298538] Bluetooth: RFCOMM ver 1.11
[   15.305397] hwmon hwmon1: temp1_input not attached to any thermal zone
[   15.364292] PPP generic driver version 2.4.2
[   15.365178] NET: Registered PF_PPPOX protocol family
[   15.375998] ath11k c000000.wifi: ipq8074 hw2.0
[   15.376032] ath11k c000000.wifi: FW memory mode: 0
[   15.406120] remoteproc remoteproc0: powering up cd00000.q6v5_wcss
[   15.406456] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[   16.137037] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up
[   16.181038] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[   16.188508] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0xff soc_id 0xffffffff
[   16.188544] ath11k c000000.wifi: fw_version 0x290604a5 fw_build_timestamp 2023-10-12 02:06 fw_build_id WLAN.HK.2.9.0.1-01977-QCAHKSWPL_SILICONZ-1
[   16.478435] remoteproc remoteproc0: stopped remote processor cd00000.q6v5_wcss
[   16.478484] remoteproc remoteproc0: powering up cd00000.q6v5_wcss
[   16.484812] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668
[   16.834218] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up
[   16.838076] kmodloader: done loading kernel modules from /etc/modules.d/*
[   16.878123] ath11k c000000.wifi: qmi ignore invalid mem req type 3
[   16.885564] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0xff soc_id 0xffffffff
[   16.885606] ath11k c000000.wifi: fw_version 0x290604a5 fw_build_timestamp 2023-10-12 02:06 fw_build_id WLAN.HK.2.9.0.1-01977-QCAHKSWPL_SILICONZ-1
[   17.273224] ath11k c000000.wifi: htt event 48 not handled
[   21.625758] br-lan: port 1(lan1) entered blocking state
[   21.625806] br-lan: port 1(lan1) entered disabled state
[   21.629847] nss-dp 3a001000.dp1 lan1: entered allmulticast mode
[   21.635354] nss-dp 3a001000.dp1 lan1: entered promiscuous mode
[   21.652939] br-lan: port 2(lan2) entered blocking state
[   21.652988] br-lan: port 2(lan2) entered disabled state
[   21.657135] nss-dp 3a001200.dp2 lan2: entered allmulticast mode
[   21.662406] nss-dp 3a001200.dp2 lan2: entered promiscuous mode
[   21.672480] br-lan: port 3(lan3) entered blocking state
[   21.674003] br-lan: port 3(lan3) entered disabled state
[   21.679265] nss-dp 3a001400.dp3 lan3: entered allmulticast mode
[   21.684588] nss-dp 3a001400.dp3 lan3: entered promiscuous mode
[   21.695252] br-lan: port 4(lan4) entered blocking state
[   21.696148] br-lan: port 4(lan4) entered disabled state
[   21.701313] nss-dp 3a001600.dp4 lan4: entered allmulticast mode
[   21.706735] nss-dp 3a001600.dp4 lan4: entered promiscuous mode
[   21.721744] br-lan: port 5(10g) entered blocking state
[   21.721788] br-lan: port 5(10g) entered disabled state
[   21.725913] nss-dp 3a007000.dp6-syn 10g: entered allmulticast mode
[   21.731544] nss-dp 3a007000.dp6-syn 10g: entered promiscuous mode
[   24.725128] nss-dp 3a001000.dp1 lan1: PHY Link up speed: 1000
[   24.725190] br-lan: port 1(lan1) entered blocking state
[   24.729871] br-lan: port 1(lan1) entered forwarding state
[   24.885253] nss-dp 3a001800.dp5 wan: PHY Link up speed: 1000
[   25.765089] nss-dp 3a001000.dp1 lan1: PHY Link is down
[   25.765344] br-lan: port 1(lan1) entered disabled state
[   25.845623] nss-dp 3a001600.dp4 lan4: PHY Link up speed: 1000
[   25.845671] br-lan: port 4(lan4) entered blocking state
[   25.850353] br-lan: port 4(lan4) entered forwarding state
[   27.845141] nss-dp 3a001000.dp1 lan1: PHY Link up speed: 1000
[   27.845201] br-lan: port 1(lan1) entered blocking state
[   27.849879] br-lan: port 1(lan1) entered forwarding state
Starting kernel ...

Jumping to AARCH64 kernel via monitor

[20/02/2023 11:33:00] Booting Linux on physical CPU 0x0
[20/02/2023 11:33:00] Initializing cgroup subsys cpuset
[20/02/2023 11:33:00] Initializing cgroup subsys cpu
[20/02/2023 11:33:00] Initializing cgroup subsys cpuacct
[20/02/2023 11:33:00] Linux version 4.4.60 (openwrt@0e6791bdf6c5) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 eb4b1a4+r49254) ) #1 SMP PREEMPT Wed Sep 29 08:31:14 UTC 2021
[20/02/2023 11:33:00] Boot CPU: AArch64 Processor [410fd034]
[20/02/2023 11:33:00] Ignoring memory range 0x40000000 - 0x41000000
[20/02/2023 11:33:00] efi: Getting EFI parameters from FDT:
[20/02/2023 11:33:00] efi: UEFI not found.
[20/02/2023 11:33:00] Reserved memory: OVERLAP DETECTED!
[20/02/2023 11:33:00] wifi_dump@51000000 (0x0000000051000000--0x0000000051600000) overlaps with wigig_dump@51200000 (0x0000000051200000--0x0000000051600000)
[20/02/2023 11:33:00] On node 0 totalpages: 228864
[20/02/2023 11:33:00] DMA zone: 3576 pages used for memmap
[20/02/2023 11:33:00] DMA zone: 0 pages reserved
[20/02/2023 11:33:00] DMA zone: 228864 pages, LIFO batch:31
[20/02/2023 11:33:00] psci: probing for conduit method from DT.
[20/02/2023 11:33:00] psci: PSCIv1.0 detected in firmware.
[20/02/2023 11:33:00] psci: Using standard PSCI v0.2 function IDs
[20/02/2023 11:33:00] psci: MIGRATE_INFO_TYPE not supported.
[20/02/2023 11:33:00] PERCPU: Embedded 15 pages/cpu @ffffffc03ef52000 s21120 r8192 d32128 u61440
[20/02/2023 11:33:00] pcpu-alloc: s21120 r8192 d32128 u61440 alloc=15*4096
[20/02/2023 11:33:00] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
[20/02/2023 11:33:00] Detected VIPT I-cache on CPU0
[20/02/2023 11:33:00] CPU features: enabling workaround for ARM erratum 845719
[20/02/2023 11:33:00] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 225288
[20/02/2023 11:33:00] Kernel command line: console=ttyMSM0,115200n8 root=PARTUUID=a0bb3852-36cc-ac69-a1a2-6bd39ff56f0a rootwait swiotlb=1
[20/02/2023 11:33:00] PID hash table entries: 4096 (order: 3, 32768 bytes)
[20/02/2023 11:33:00] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[20/02/2023 11:33:00] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[20/02/2023 11:33:00] software IO TLB [mem 0x7fe0a000-0x7fe4a000] (0MB) mapped at [ffffffc03ee0a000-ffffffc03ee49fff]
[20/02/2023 11:33:00] Memory: 887072K/915456K available (5602K kernel code, 637K rwdata, 2380K rodata, 232K init, 406K bss, 28384K reserved, 0K cma-reserved)
[20/02/2023 11:33:00] Virtual kernel memory layout:
[20/02/2023 11:33:00] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000   (   246 GB)
[20/02/2023 11:33:00] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000   (     8 GB maximum)
[20/02/2023 11:33:00] 0xffffffbdc0040000 - 0xffffffbdc1000000   (    15 MB actual)
[20/02/2023 11:33:00] fixed   : 0xffffffbffa7fd000 - 0xffffffbffac00000   (  4108 KB)
[20/02/2023 11:33:00] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000   (    16 MB)
[20/02/2023 11:33:00] modules : 0xffffffbffc000000 - 0xffffffc000000000   (    64 MB)
[20/02/2023 11:33:00] memory  : 0xffffffc000000000 - 0xffffffc03f000000   (  1008 MB)
[20/02/2023 11:33:00] .init : 0xffffffc00084e000 - 0xffffffc000888000   (   232 KB)
[20/02/2023 11:33:00] .text : 0xffffffc000080000 - 0xffffffc00084da14   (  7991 KB)
[20/02/2023 11:33:00] .data : 0xffffffc000898000 - 0xffffffc000937400   (   637 KB)
[20/02/2023 11:33:00] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[20/02/2023 11:33:00] Preemptible hierarchical RCU implementation.
[20/02/2023 11:33:00] Build-time adjustment of leaf fanout to 64.
[20/02/2023 11:33:00] NR_IRQS:64 nr_irqs:64 0
[20/02/2023 11:33:00] Architected cp15 timer(s) running at 19.20MHz (virt).
[20/02/2023 11:33:00] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns
[20/02/2023 11:33:00] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns
[20/02/2023 11:33:00] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
[20/02/2023 11:33:00] pid_max: default: 32768 minimum: 301
[20/02/2023 11:33:00] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[20/02/2023 11:33:00] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[20/02/2023 11:33:00] Initializing cgroup subsys io
[20/02/2023 11:33:00] Initializing cgroup subsys memory
[20/02/2023 11:33:00] Initializing cgroup subsys devices
[20/02/2023 11:33:00] Initializing cgroup subsys freezer
[20/02/2023 11:33:00] Initializing cgroup subsys net_cls
[20/02/2023 11:33:00] Initializing cgroup subsys pids
[20/02/2023 11:33:00] EFI services will not be available.
[20/02/2023 11:33:00] ASID allocator initialised with 65536 entries
[20/02/2023 11:33:00] MSM Memory Dump base table set up
[20/02/2023 11:33:00] MSM Memory Dump apps data table set up
[20/02/2023 11:33:00] Detected VIPT I-cache on CPU1
[20/02/2023 11:33:00] CPU1: Booted secondary processor [410fd034]
[20/02/2023 11:33:00] Detected VIPT I-cache on CPU2
[20/02/2023 11:33:00] CPU2: Booted secondary processor [410fd034]
[20/02/2023 11:33:00] Detected VIPT I-cache on CPU3
[20/02/2023 11:33:00] CPU3: Booted secondary processor [410fd034]
[20/02/2023 11:33:00] Brought up 4 CPUs
[20/02/2023 11:33:00] SMP: Total of 4 processors activated.
[20/02/2023 11:33:00] CPU: All CPU(s) started at EL1
[20/02/2023 11:33:00] alternatives: patching kernel code
[20/02/2023 11:33:00] DMI not present or invalid.
[20/02/2023 11:33:00] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[20/02/2023 11:33:00] futex hash table entries: 1024 (order: 5, 131072 bytes)
[20/02/2023 11:33:00] pinctrl core: initialized pinctrl subsystem
[20/02/2023 11:33:00] NET: Registered protocol family 16
[20/02/2023 11:33:00] cpuidle: using governor ladder
[20/02/2023 11:33:00] cpuidle: using governor menu
[20/02/2023 11:33:00] vdso: 2 pages (1 code @ ffffffc00089d000, 1 data @ ffffffc00089c000)
[20/02/2023 11:33:00] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[20/02/2023 11:33:00] DMA: preallocated 256 KiB pool for atomic allocations
[20/02/2023 11:33:00] CPU: unavail, SoC Version: 2.0
[20/02/2023 11:33:00] <CORE> glink_init: IPC Logging Disabled
[20/02/2023 11:33:00] IPC logging disabled
[20/02/2023 11:33:00] IPC logging disabled
[20/02/2023 11:33:00] IPC logging disabled
[20/02/2023 11:33:00] IPC logging disabled
[20/02/2023 11:33:00] IPC logging disabled
[20/02/2023 11:33:00] gpiochip_add: registered GPIOs 0 to 69 on device: 1000000.pinctrl
[20/02/2023 11:33:00] GPIO chip 1000000.pinctrl: created GPIO range 0->69 ==> 1000000.pinctrl PIN 0->69
[20/02/2023 11:33:00] Soc version is not 1, changing clock offsets
[20/02/2023 11:33:00] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[20/02/2023 11:33:00] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel !
[20/02/2023 11:33:00] msm_rpm_dev_probe: APSS-RPM communication over GLINK
[20/02/2023 11:33:00] sps:sps is ready.
[20/02/2023 11:33:00] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[20/02/2023 11:33:00] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2
[20/02/2023 11:33:00] of_get_named_gpiod_flags: can't parse 'gpio' property of node '/fixed-regulator@0[0]'
[20/02/2023 11:33:00] pps_core: LinuxPPS API ver. 1 registered
[20/02/2023 11:33:00] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[20/02/2023 11:33:00] PTP clock support registered
[20/02/2023 11:33:00] dmi: Firmware registration failed.
[20/02/2023 11:33:00] Advanced Linux Sound Architecture Driver Initialized.
[20/02/2023 11:33:00] clocksource: Switched to clocksource arch_sys_counter
[20/02/2023 11:33:00] NET: Registered protocol family 2
[20/02/2023 11:33:00] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[20/02/2023 11:33:00] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[20/02/2023 11:33:00] TCP: Hash tables configured (established 8192 bind 8192)
[20/02/2023 11:33:00] UDP hash table entries: 512 (order: 2, 16384 bytes)
[20/02/2023 11:33:00] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[20/02/2023 11:33:00] NET: Registered protocol family 1
[20/02/2023 11:33:00] PCI: CLS 0 bytes, default 128
[20/02/2023 11:33:00] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[20/02/2023 11:33:00] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[20/02/2023 11:33:00] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[20/02/2023 11:33:00] fuse init (API version 7.23)
[20/02/2023 11:33:00] Key type asymmetric registered
[20/02/2023 11:33:00] Asymmetric key parser 'x509' registered
[20/02/2023 11:33:00] io scheduler noop registered
[20/02/2023 11:33:00] io scheduler deadline registered (default)
[20/02/2023 11:33:00] qcom-pcie 20000000.pci: GPIO lookup for consumer perst
[20/02/2023 11:33:00] qcom-pcie 20000000.pci: using device tree for GPIO lookup
[20/02/2023 11:33:00] of_get_named_gpiod_flags: can't parse 'perst-gpios' property of node '/soc/pci@20000000[0]'
[20/02/2023 11:33:00] of_get_named_gpiod_flags: parsed 'perst-gpio' property of node '/soc/pci@20000000[0]' - status (0)
[20/02/2023 11:33:00] 20000000.pci supply vdda not found, using dummy regulator
[20/02/2023 11:33:00] 20000000.pci supply vdda_phy not found, using dummy regulator
[20/02/2023 11:33:00] 20000000.pci supply vdda_refclk not found, using dummy regulator
[20/02/2023 11:33:00] PCI host bridge /soc/pci@20000000 ranges:
[20/02/2023 11:33:00] IO 0x20200000..0x202fffff -> 0x20200000
[20/02/2023 11:33:00] MEM 0x20300000..0x20ffffff -> 0x20300000
[20/02/2023 11:33:01] qcom-pcie 20000000.pci: phy link never came up
[20/02/2023 11:33:01] qcom-pcie 20000000.pci: hostinit failed
[20/02/2023 11:33:01] qcom-pcie 20000000.pci: cannot initialize host
[20/02/2023 11:33:01] qcom-pcie: probe of 20000000.pci failed with error -110
[20/02/2023 11:33:01] qcom-pcie 10000000.pci: GPIO lookup for consumer perst
[20/02/2023 11:33:01] qcom-pcie 10000000.pci: using device tree for GPIO lookup
[20/02/2023 11:33:01] of_get_named_gpiod_flags: can't parse 'perst-gpios' property of node '/soc/pci@10000000[0]'
[20/02/2023 11:33:01] of_get_named_gpiod_flags: parsed 'perst-gpio' property of node '/soc/pci@10000000[0]' - status (0)
[20/02/2023 11:33:01] 10000000.pci supply vdda not found, using dummy regulator
[20/02/2023 11:33:01] 10000000.pci supply vdda_phy not found, using dummy regulator
[20/02/2023 11:33:01] 10000000.pci supply vdda_refclk not found, using dummy regulator
[20/02/2023 11:33:01] PCI host bridge /soc/pci@10000000 ranges:
[20/02/2023 11:33:01] IO 0x10200000..0x102fffff -> 0x10200000
[20/02/2023 11:33:01] MEM 0x10300000..0x10ffffff -> 0x10300000
[20/02/2023 11:33:02] qcom-pcie 10000000.pci: phy link never came up
[20/02/2023 11:33:02] qcom-pcie 10000000.pci: hostinit failed
[20/02/2023 11:33:02] qcom-pcie 10000000.pci: cannot initialize host
[20/02/2023 11:33:02] qcom-pcie: probe of 10000000.pci failed with error -110
[20/02/2023 11:33:02] MDSS QPIC HW Base phy_Address=0x7980000 virt=ffffff80004c0000
[20/02/2023 11:33:02] mdss_qpic_panel_probe: Panel Name = qpic lcd panel
[20/02/2023 11:33:02] mdss_fb_register: FrameBuffer[0] 800x480 registered successfully!
[20/02/2023 11:33:02] NET: Registered protocol family 27
[20/02/2023 11:33:02] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled
[20/02/2023 11:33:02] qmi_log_init: IPC Logging disabled
[20/02/2023 11:33:02] qmi_log_init: IPC Logging disabled
[20/02/2023 11:33:02] msm_rpm_log_probe: OK
[20/02/2023 11:33:02] msm-dcc b3000.dcc: DCC XPU is not specified
[20/02/2023 11:33:02] msm-dcc b3000.dcc: DCC SRAM dump setup failed
[20/02/2023 11:33:02] msm-dcc b3000.dcc: jiffies_64: 0xffff8bbe, cntvct_64: 0x77ff162c
[20/02/2023 11:33:02] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xffffff80003de004)
[20/02/2023 11:33:02] msm-dcc b3000.dcc: gcnt_lo: 0x77ff17db(0xffffff80003de000)
[20/02/2023 11:33:02] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set
[20/02/2023 11:33:02] msm_serial 78b3000.serial: msm_serial: detected port #0
[20/02/2023 11:33:02] msm_serial 78b3000.serial: uartclk = 3686400
[20/02/2023 11:33:02] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 77, base_baud = 230400) is a MSM
[20/02/2023 11:33:02] msm_serial: console setup on port #0
[20/02/2023 11:33:03] console [ttyMSM0] enabled
[20/02/2023 11:33:03] msm_serial 78b1000.serial: msm_serial: detected port #1
[20/02/2023 11:33:03] msm_serial 78b1000.serial: uartclk = 19200000
[20/02/2023 11:33:03] 78b1000.serial: ttyMSM1 at MMIO 0x78b1000 (irq = 78, base_baud = 1200000) is a MSM
[20/02/2023 11:33:03] msm_serial: driver initialized
[20/02/2023 11:33:03] msm_serial_hsl_init: driver initialized
[20/02/2023 11:33:03] brd: module loaded
[20/02/2023 11:33:03] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64
[20/02/2023 11:33:03] m25p80 spi32766.0: found w25q64dw, expected n25q128a11
[20/02/2023 11:33:03] m25p80 spi32766.0: w25q64dw (8192 Kbytes)
[20/02/2023 11:33:03] 22 ofpart partitions found on MTD device spi32766.0
[20/02/2023 11:33:03] Creating 22 MTD partitions on "spi32766.0":
[20/02/2023 11:33:03] 0x000000000000-0x000000050000 : "0:SBL1"
[20/02/2023 11:33:03] 0x000000050000-0x000000060000 : "0:MIBIB"
[20/02/2023 11:33:03] 0x000000060000-0x000000080000 : "0:BOOTCONFIG"
[20/02/2023 11:33:03] 0x000000080000-0x0000000a0000 : "0:BOOTCONFIG1"
[20/02/2023 11:33:03] 0x0000000a0000-0x000000220000 : "0:QSEE"
[20/02/2023 11:33:03] 0x000000220000-0x0000003a0000 : "0:QSEE_1"
[20/02/2023 11:33:03] 0x0000003a0000-0x0000003b0000 : "0:DEVCFG"
[20/02/2023 11:33:03] 0x0000003b0000-0x0000003c0000 : "0:DEVCFG_1"
[20/02/2023 11:33:03] 0x0000003c0000-0x0000003d0000 : "0:APDP"
[20/02/2023 11:33:03] 0x0000003d0000-0x0000003e0000 : "0:APDP_1"
[20/02/2023 11:33:03] 0x0000003e0000-0x000000420000 : "0:RPM"
[20/02/2023 11:33:03] 0x000000420000-0x000000460000 : "0:RPM_1"
[20/02/2023 11:33:03] 0x000000460000-0x000000470000 : "0:CDT"
[20/02/2023 11:33:03] 0x000000470000-0x000000480000 : "0:CDT_1"
[20/02/2023 11:33:03] 0x000000480000-0x000000540000 : "0:APPSBL"
[20/02/2023 11:33:03] 0x000000540000-0x000000600000 : "0:APPSBL_1"
[20/02/2023 11:33:03] 0x000000600000-0x000000610000 : "0:APPSBLENV"
[20/02/2023 11:33:03] 0x000000610000-0x000000650000 : "0:ART"
[20/02/2023 11:33:03] 0x000000650000-0x0000006d0000 : "0:ETHPHYFW"
[20/02/2023 11:33:03] 0x0000006d0000-0x0000006e0000 : "0:CRT"
[20/02/2023 11:33:03] 0x0000006e0000-0x0000006f0000 : "DUAL_FLAG"
[20/02/2023 11:33:03] 0x0000006f0000-0x000000800000 : "RESERVED"
[20/02/2023 11:33:03] spmi spmi-0: PMIC Arb Version-2 (0x20010000)
[20/02/2023 11:33:03] libphy: Fixed MDIO Bus: probed
[20/02/2023 11:33:03] of_get_named_gpiod_flags: parsed 'phy-reset-gpio' property of node '/soc/mdio@90000[0]' - status (0)
[20/02/2023 11:33:03] of_get_named_gpiod_flags: parsed 'phy-reset-gpio' property of node '/soc/mdio@90000[1]' - status (0)
[20/02/2023 11:33:03] of_get_named_gpiod_flags: can't parse 'phy-reset-gpio' property of node '/soc/mdio@90000[2]'
[20/02/2023 11:33:03] qca-mdio 90000.mdio: Could not find phy-reset-gpio
[20/02/2023 11:33:03] libphy: qca_mdio: probed
[20/02/2023 11:33:03] qca-mdio 90000.mdio: qca-mdio driver was registered
[20/02/2023 11:33:03] Unable to create IPC log context!
[20/02/2023 11:33:03] cnss: Platform driver probed successfully.
[20/02/2023 11:33:03] Skip QCA8074V1 in V2 platform
[20/02/2023 11:33:03] cnss_genl: genl_register_family fail: -17
[20/02/2023 11:33:03] cnss: CNSS genl init failed -17
[20/02/2023 11:33:03] cnss: Platform driver probed successfully.
[20/02/2023 11:33:03] i2c /dev entries driver
[20/02/2023 11:33:03] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com
[20/02/2023 11:33:03] sdhci: Secure Digital Host Controller Interface driver
[20/02/2023 11:33:03] sdhci: Copyright(c) Pierre Ossman
[20/02/2023 11:33:03] sdhci-pltfm: SDHCI platform and OF driver helper
[20/02/2023 11:33:03] qcom_ice_get_pdevice: invalid device list
[20/02/2023 11:33:03] sdhci_msm 7824900.sdhci: sdhci_msm_ice_get_dev: ICE device not probed yet
[20/02/2023 11:33:03] sdhci_msm 7824900.sdhci: sdhci_msm_probe: required ICE device not probed yet err = -517
[20/02/2023 11:33:03] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/soc/i2c@78b6000/lp5569@32[0]'
[20/02/2023 11:33:03] lp5569x 0-0032: lp5569 Programmable led chip found
[20/02/2023 11:33:03] of_get_named_gpiod_flags: can't parse 'enable-gpio' property of node '/soc/i2c@78b6000/lp5569@35[0]'
[20/02/2023 11:33:04] lp5569x 0-0035: lp5569 Programmable led chip found
[20/02/2023 11:33:04] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed
[20/02/2023 11:33:04] ICE IRQ = 81
[20/02/2023 11:33:04]
[20/02/2023 11:33:04] Version Rollback Feature Disabled
[20/02/2023 11:33:04] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000008b04000
[20/02/2023 11:33:04] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000008b04000
[20/02/2023 11:33:04] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000008b04000
[20/02/2023 11:33:04] sps:BAM 0x0000000008b04000 is registered.<0>[    4.078636] DEV CI test message
[20/02/2023 11:33:04] subsys-restart: ssr_parse_restart_orders(): q6v5_m3 device has been added to q6v5-m3's restart group
[20/02/2023 11:33:04] subsys-restart: ssr_parse_restart_orders(): q6v5_wcss device has been added to q6v5-m3's restart group
[20/02/2023 11:33:04] remoteproc remoteproc0: q6v5-m3 is available
[20/02/2023 11:33:04] SPMI VADC - Min ch: 0 Max ch: 15
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000
[20/02/2023 11:33:04] coresight-csr 6001000.csr: CSR initialized
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000
[20/02/2023 11:33:04] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000006044000
[20/02/2023 11:33:04] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000006044000
[20/02/2023 11:33:04] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000006044000
[20/02/2023 11:33:04] sps:BAM 0x0000000006044000 is registered.<6>[    4.324410] coresight-tmc 6028000.tmc: TMC initialized
[20/02/2023 11:33:04] coresight-tmc 6027000.tmc: TMC initialized
[20/02/2023 11:33:04] coresight-funnel 6021000.funnel: FUNNEL initialized
[20/02/2023 11:33:04] coresight-funnel 6100000.funnel: FUNNEL initialized
[20/02/2023 11:33:04] coresight-funnel 6120000.funnel: FUNNEL initialized
[20/02/2023 11:33:04] coresight-funnel 61a1000.funnel: FUNNEL initialized
[20/02/2023 11:33:04] coresight-etm4x 619c000.etm: ETM 4.0 initialized
[20/02/2023 11:33:04] coresight-etm4x 619d000.etm: ETM 4.0 initialized
[20/02/2023 11:33:04] coresight-etm4x 619e000.etm: ETM 4.0 initialized
[20/02/2023 11:33:04] coresight-etm4x 619f000.etm: ETM 4.0 initialized
[20/02/2023 11:33:04] coresight-replicator-qcom 6026000.replicator: REPLICATOR 1.0 initialized
[20/02/2023 11:33:04] coresight-stm 6002000.stm: STM initialized
[20/02/2023 11:33:04] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000
[20/02/2023 11:33:04] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized
[20/02/2023 11:33:04] Netfilter messages via NETLINK v0.30.
[20/02/2023 11:33:04] nf_conntrack version 0.5.0 (6930 buckets, 27720 max)
[20/02/2023 11:33:04] ctnetlink v0.93: registering with nfnetlink.
[20/02/2023 11:33:04] NET: Registered protocol family 10
[20/02/2023 11:33:04] NET: Registered protocol family 17
[20/02/2023 11:33:04] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this.
[20/02/2023 11:33:04] Bridge firewalling registered
[20/02/2023 11:33:04] 8021q: 802.1Q VLAN Support v1.8
[20/02/2023 11:33:04] <CORE> glink_core_register_transport: IPC Logging disabled
[20/02/2023 11:33:04] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4
[20/02/2023 11:33:04] msm_glink_smem_native_xprt	rx fifo not found
[20/02/2023 11:33:04] pmd9655_s3: supplied by e-smps1-reg
[20/02/2023 11:33:04] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0
[20/02/2023 11:33:04] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1
[20/02/2023 11:33:04] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0
[20/02/2023 11:33:04] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable
[20/02/2023 11:33:04] cpr3_mem_acc_init: apc: not using memory accelerator regulator
[20/02/2023 11:33:04] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      SVS: open-loop= 712000 uV
[20/02/2023 11:33:04] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      NOM: open-loop= 832000 uV
[20/02/2023 11:33:04] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused    TURBO: open-loop= 904000 uV
[20/02/2023 11:33:04] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused   STURBO: open-loop= 992000 uV
[20/02/2023 11:33:04] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      SVS: quot[ 7]= 701, quot_offset[ 7]=   0
[20/02/2023 11:33:04] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      NOM: quot[ 7]= 925, quot_offset[ 7]= 220
[20/02/2023 11:33:04] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused    TURBO: quot[ 7]=1045, quot_offset[ 7]= 120
[20/02/2023 11:33:04] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused   STURBO: quot[ 7]=1198, quot_offset[ 7]= 150
[20/02/2023 11:33:04] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop
[20/02/2023 11:33:04] qcom,cpr3-npu-regulator a4000.npu-cpr: NPU CPR valid fuse count: 2
[20/02/2023 11:33:04] pmd9655_s4: supplied by e-smps1-reg
[20/02/2023 11:33:04] cpr3_mem_acc_init: npu: not using memory accelerator regulator
[20/02/2023 11:33:04] npu_corner: fused      NOM: open-loop= 800000 uV
[20/02/2023 11:33:04] npu_corner: fused    TURBO: open-loop= 880000 uV
[20/02/2023 11:33:04] npu_corner: fused      NOM: open-loop= 800000 uV
[20/02/2023 11:33:04] npu_corner: fused    TURBO: open-loop= 880000 uV
[20/02/2023 11:33:04] npu_corner: Normal and Cold condition init done. Default to normal.
[20/02/2023 11:33:04] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz
[20/02/2023 11:33:04] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1017600 KHz
[20/02/2023 11:33:04] qcom_ice_get_pdevice: found ice device ffffffc03cf08a00
[20/02/2023 11:33:04] qcom_ice_get_pdevice: matching platform device ffffffc03d575c00
[20/02/2023 11:33:04] of_get_named_gpiod_flags: can't parse 'cd-gpios' property of node '/soc/sdhci@7824900[0]'
[20/02/2023 11:33:04] of_get_named_gpiod_flags: can't parse 'sd-ldo-gpios' property of node '/soc/sdhci@7824900[0]'
[20/02/2023 11:33:04] sdhci_msm 7824900.sdhci: No vreg data found for vdd
[20/02/2023 11:33:04] sdhci_msm 7824900.sdhci: No vreg data found for vdd-io
[20/02/2023 11:33:04] qcom_ice 7803000.sdcc1ice: QC ICE 2.1.44 device found @0xffffff80008c8000
[20/02/2023 11:33:04] sdhci_msm 7824900.sdhci: No vmmc regulator found
[20/02/2023 11:33:04] sdhci_msm 7824900.sdhci: No vqmmc regulator found
[20/02/2023 11:33:04] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit
[20/02/2023 11:33:04] DEV CI test message
[20/02/2023 11:33:04] remoteproc remoteproc1: q6v5-wcss is available
[20/02/2023 11:33:04] hctosys: unable to open rtc device (rtc0)
[20/02/2023 11:33:04] pmd9655_ldo11: disabling
[20/02/2023 11:33:04] ALSA device list:
[20/02/2023 11:33:04] No soundcards found.
[20/02/2023 11:33:04] Waiting for root device PARTUUID=a0bb3852-36cc-ac69-a1a2-6bd39ff56f0a...
[20/02/2023 11:33:04] mmc0: MAN_BKOPS_EN bit is not set
[20/02/2023 11:33:04] mmc0: new high speed MMC card at address 0001
[20/02/2023 11:33:04] mmcblk0: mmc0:0001 M62704 3.53 GiB
[20/02/2023 11:33:04] mmcblk0rpmb: mmc0:0001 M62704 partition 3 512 KiB
[20/02/2023 11:33:04] GPT: device [179:4] (rootfs) set to be root filesystem
[20/02/2023 11:33:04] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11
[20/02/2023 11:33:04] VFS: Mounted root (squashfs filesystem) readonly on device 179:8.
[20/02/2023 11:33:04] Freeing unused kernel memory: 232K (ffffffc00084e000 - ffffffc000888000)
[20/02/2023 11:33:04] Freeing alternatives memory: 44K (ffffffc000888000 - ffffffc000893000)
[20/02/2023 11:33:05] init: Console is alive
[20/02/2023 11:33:05] init: - watchdog -
[20/02/2023 11:33:05] usbcore: registered new interface driver usbfs
[20/02/2023 11:33:05] usbcore: registered new interface driver hub
[20/02/2023 11:33:05] usbcore: registered new device driver usb
[20/02/2023 11:33:05] Button Hotplug driver version 0.4.1
[20/02/2023 11:33:05] of_get_named_gpiod_flags: parsed 'gpios' property of node '/soc/gpio_keys/button@1[0]' - status (0)
[20/02/2023 11:33:05] SCSI subsystem initialized
[20/02/2023 11:33:05] libata version 3.00 loaded.
[20/02/2023 11:33:05] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[20/02/2023 11:33:05] ehci-platform: EHCI generic platform driver
[20/02/2023 11:33:05] msm-usb-ssphy-qmp 78000.ssphy: Initializing QMP phy
[20/02/2023 11:33:05] msm-usb-ssphy-qmp 78000.ssphy: QMP PHY initialization timeout
[20/02/2023 11:33:05] msm-usb-ssphy-qmp 78000.ssphy: USB3_PHY_PCS_STATUS:68686868
[20/02/2023 11:33:06] msm-usb-ssphy-qmp 58000.ssphy: Initializing QMP phy
[20/02/2023 11:33:06] msm-usb-ssphy-qmp 58000.ssphy: QMP PHY initialization timeout
[20/02/2023 11:33:06] msm-usb-ssphy-qmp 58000.ssphy: USB3_PHY_PCS_STATUS:68686868
[20/02/2023 11:33:06] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[20/02/2023 11:33:06] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[20/02/2023 11:33:06] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x00010010
[20/02/2023 11:33:06] xhci-hcd xhci-hcd.0.auto: irq 211, io mem 0x08a00000
[20/02/2023 11:33:06] hub 1-0:1.0: USB hub found
[20/02/2023 11:33:06] hub 1-0:1.0: 1 port detected
[20/02/2023 11:33:06] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[20/02/2023 11:33:06] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[20/02/2023 11:33:06] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[20/02/2023 11:33:06] hub 2-0:1.0: USB hub found
[20/02/2023 11:33:06] hub 2-0:1.0: 1 port detected
[20/02/2023 11:33:06] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[20/02/2023 11:33:06] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3
[20/02/2023 11:33:06] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x00010010
[20/02/2023 11:33:06] xhci-hcd xhci-hcd.1.auto: irq 212, io mem 0x08c00000
[20/02/2023 11:33:06] hub 3-0:1.0: USB hub found
[20/02/2023 11:33:06] hub 3-0:1.0: 1 port detected
[20/02/2023 11:33:06] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller
[20/02/2023 11:33:06] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4
[20/02/2023 11:33:06] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM.
[20/02/2023 11:33:06] hub 4-0:1.0: USB hub found
[20/02/2023 11:33:06] hub 4-0:1.0: 1 port detected
[20/02/2023 11:33:06] usbcore: registered new interface driver usb-storage
[20/02/2023 11:33:06] usbcore: registered new interface driver uas
[20/02/2023 11:33:06] usb 3-1: new high-speed USB device number 2 using xhci-hcd
[20/02/2023 11:33:06] hub 3-1:1.0: USB hub found
[20/02/2023 11:33:06] hub 3-1:1.0: 4 ports detected
[20/02/2023 11:33:06] usb 4-1: new SuperSpeed USB device number 2 using xhci-hcd
[20/02/2023 11:33:06] hub 4-1:1.0: USB hub found
[20/02/2023 11:33:06] hub 4-1:1.0: 4 ports detected
[20/02/2023 11:33:07] init: - preinit -
[20/02/2023 11:33:07] usb 3-1.4: new high-speed USB device number 3 using xhci-hcd
[20/02/2023 11:33:07] random: procd: uninitialized urandom read (4 bytes read, 8 bits of entropy available)
[20/02/2023 11:33:07] usb-storage 3-1.4:1.0: USB Mass Storage device detected
[20/02/2023 11:33:07] scsi host0: usb-storage 3-1.4:1.0
[20/02/2023 11:33:07] usb 4-1.3: new SuperSpeed USB device number 3 using xhci-hcd
[20/02/2023 11:33:07] usb-storage 4-1.3:1.0: USB Mass Storage device detected
[20/02/2023 11:33:07] scsi host1: usb-storage 4-1.3:1.0
[20/02/2023 11:33:08] scsi 0:0:0:0: Direct-Access      USB      SanDisk 3.2Gen1 1.00 PQ: 0 ANSI: 6
[20/02/2023 11:33:08] sd 0:0:0:0: [sda] 240328704 512-byte logical blocks: (123 GB/115 GiB)
[20/02/2023 11:33:08] sd 0:0:0:0: [sda] Write Protect is off
[20/02/2023 11:33:08] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
[20/02/2023 11:33:08] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[20/02/2023 11:33:08] sda: sda1 sda2
[20/02/2023 11:33:08] sd 0:0:0:0: [sda] Attached SCSI removable disk
[20/02/2023 11:33:08] scsi 1:0:0:0: Direct-Access     ATA      ADATA SU650      2A   PQ: 0 ANSI: 6
[20/02/2023 11:33:08] sd 1:0:0:0: [sdb] 234441648 512-byte logical blocks: (120 GB/112 GiB)
[20/02/2023 11:33:08] sd 1:0:0:0: [sdb] Write Protect is off
[20/02/2023 11:33:08] sd 1:0:0:0: [sdb] Mode Sense: 43 00 00 00
[20/02/2023 11:33:08] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[20/02/2023 11:33:08] sdb: sdb1
[20/02/2023 11:33:08] sd 1:0:0:0: [sdb] Attached SCSI disk
[20/02/2023 11:33:09] EXT4-fs (mmcblk0p1): mounted filesystem with ordered data mode. Opts: (null)
[20/02/2023 11:33:09] mount_root: switching to jffs2 overlay
[20/02/2023 11:33:09] procd: - early -
[20/02/2023 11:33:09] procd: - watchdog -
[20/02/2023 11:33:10] procd: - ubus -
[20/02/2023 11:33:10] FAT-fs (sda): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[20/02/2023 11:33:11] random: ubusd: uninitialized urandom read (4 bytes read, 61 bits of entropy available)
[20/02/2023 11:33:11] random: ubusd: uninitialized urandom read (4 bytes read, 61 bits of entropy available)
[20/02/2023 11:33:11] random: ubusd: uninitialized urandom read (4 bytes read, 61 bits of entropy available)
[20/02/2023 11:33:11] random: ubusd: uninitialized urandom read (4 bytes read, 61 bits of entropy available)
[20/02/2023 11:33:11] random: ubusd: uninitialized urandom read (4 bytes read, 61 bits of entropy available)
[20/02/2023 11:33:11] random: ubusd: uninitialized urandom read (4 bytes read, 61 bits of entropy available)
[20/02/2023 11:33:11] random: ubusd: uninitialized urandom read (4 bytes read, 61 bits of entropy available)
[20/02/2023 11:33:11] procd: - init -
[20/02/2023 11:33:12] FAT-fs (sdb): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[20/02/2023 11:33:12] cfg80211: World regulatory domain updated:
[20/02/2023 11:33:12] cfg80211:  DFS Master region: unset
[20/02/2023 11:33:12] cfg80211:   (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[20/02/2023 11:33:12] cfg80211:   (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[20/02/2023 11:33:12] cfg80211:   (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[20/02/2023 11:33:12] ntfs: driver 2.1.32 [Flags: R/O MODULE].
[20/02/2023 11:33:12] Initializing XFRM netlink socket
[20/02/2023 11:33:12] NET: Registered protocol family 15
[20/02/2023 11:33:12] cfg80211:   (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[20/02/2023 11:33:12] cfg80211:   (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A)
[20/02/2023 11:33:12] cfg80211:   (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s)
[20/02/2023 11:33:12] cfg80211:   (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s)
[20/02/2023 11:33:12] cfg80211:   (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[20/02/2023 11:33:12] cfg80211:   (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[20/02/2023 11:33:12] ssdk_switch_device_num_init[998]:INFO:ess-switch dts node number: 1
[20/02/2023 11:33:12] ssdk_dt_get_switch_node[836]:INFO:ess-switch DT exist!
[20/02/2023 11:33:12] ssdk_dt_parse_access_mode[737]:INFO:switch_access_mode: local bus
[20/02/2023 11:33:12] ssdk_dt_parse_access_mode[750]:INFO:switchreg_base_addr: 0x3a000000
[20/02/2023 11:33:12] ssdk_dt_parse_access_mode[751]:INFO:switchreg_size: 0x1000000
[20/02/2023 11:33:12] ssdk_dt_parse_mac_mode[242]:INFO:mac mode = 0x0
[20/02/2023 11:33:12] ssdk_dt_parse_mac_mode[251]:INFO:mac mode1 = 0xf
[20/02/2023 11:33:12] ssdk_dt_parse_mac_mode[260]:INFO:mac mode2 = 0xd
[20/02/2023 11:33:12] ssdk_dt_parse_phy_info[569]:INFO:[PORT 5] port_mac_sel = QGMAC_PORT
[20/02/2023 11:33:12] ssdk_dt_parse_uniphy[279]:INFO:ess-uniphy DT exist!
[20/02/2023 11:33:12] ssdk_dt_parse_intf_mac[683]:INFO:dp1 MAC bc:cf:4f:ff:1b:a0
[20/02/2023 11:33:12] ssdk_plat_init start
[20/02/2023 11:33:12] ssdk_ppe_clock_init[464]:INFO:ppe and uniphy clock init successfully!
[20/02/2023 11:33:12] ssdk_probe[1878]:INFO:ess_rst doesn't exist!
[20/02/2023 11:33:12] HPPE initializing...
[20/02/2023 11:33:12] *************************hsl_phytype_get_by_phyid 193 phytype=7, phy_id=4dd0b1
[20/02/2023 11:33:12] <DBG> MALIBU 8075 Found, phytype=2
[20/02/2023 11:33:12] *************************hsl_phytype_get_by_phyid 193 phytype=7, phy_id=4dd0b1
[20/02/2023 11:33:12] <DBG> MALIBU 8075 Found, phytype=2
[20/02/2023 11:33:12] *************************hsl_phytype_get_by_phyid 193 phytype=7, phy_id=4dd0b1
[20/02/2023 11:33:12] <DBG> MALIBU 8075 Found, phytype=2
[20/02/2023 11:33:12] *************************hsl_phytype_get_by_phyid 193 phytype=7, phy_id=4dd0b1
[20/02/2023 11:33:12] <DBG> MALIBU 8075 Found, phytype=2
[20/02/2023 11:33:12] *************************hsl_phytype_get_by_phyid 193 phytype=7, phy_id=4dd101
[20/02/2023 11:33:12] *************************hsl_phytype_get_by_phyid 193 phytype=7, phy_id=31c31c12
[20/02/2023 11:33:12] <DBG> AQUANTIA PHY Found, phytype=3
[20/02/2023 11:33:12] malibu_phy_api_ops_init[2851]:INFO:qca probe malibu phy driver succeeded!
[20/02/2023 11:33:12] aquantia_phy_api_ops_init[2180]:INFO:qca probe aquantia phy driver succeeded!
[20/02/2023 11:33:12] qca808x_phy_api_ops_init[2125]:INFO:qca probe qca808x phy driver succeeded!
[20/02/2023 11:33:12] qca808x_ptp_register[1377]:INFO:qca808x ptp clock registered
[20/02/2023 11:33:12] regi_init[3405]:INFO:Initializing HPPE!!
[20/02/2023 11:33:13] ssdk_ppe_reset_init[738]:INFO:ppe reset successfully!
[20/02/2023 11:33:13] qca_hppe_tdm_hw_init[737]:INFO:tdm setup num=96
[20/02/2023 11:33:13] qca_hppe_portctrl_hw_init[165]:INFO:Hawkeye PPE port initializing
[20/02/2023 11:33:14] FAT-fs (sda2): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[20/02/2023 11:33:16] ssdk_switch_register[1617]:INFO:Chip version 0x1500
[20/02/2023 11:33:16] qca_link_polling_select[1279]:INFO:link-polling-required node does not exist
[20/02/2023 11:33:16] ssdk_switch_register[1642]:INFO:polling is selected
[20/02/2023 11:33:16] regi_init[3409]:INFO:Initializing HPPE Done!!
[20/02/2023 11:33:16] regi_init[3453]:INFO:qca-ssdk module init succeeded!
[20/02/2023 11:33:16] tun: Universal TUN/TAP device driver, 1.6
[20/02/2023 11:33:16] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[20/02/2023 11:33:16] EDMA ver 1 hw init
[20/02/2023 11:33:16] EDMA HW Reset completed succesfully
[20/02/2023 11:33:16] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7)
[20/02/2023 11:33:16] RxDesc:1 (15-15) RxFill:1 (7-7)
[20/02/2023 11:33:16] GMAC2(ffffffc03ab81880) Invalid MAC@ - using 82:00:b3:cf:69:43
[20/02/2023 11:33:16] GMAC3(ffffffc03ab85880) Invalid MAC@ - using aa:7b:52:7f:8a:bb
[20/02/2023 11:33:16] GMAC4(ffffffc03ab89880) Invalid MAC@ - using 8a:2b:63:d7:e3:8e
[20/02/2023 11:33:16] GMAC5(ffffffc03ab8d880) Invalid MAC@ - using 2e:19:30:c5:35:69
[20/02/2023 11:33:16] GMAC6(ffffffc039879880) Invalid MAC@ - using 82:17:be:67:b5:cf
[20/02/2023 11:33:16] **********************************************************
[20/02/2023 11:33:16] * NSS Data Plane driver
[20/02/2023 11:33:16] **********************************************************
[20/02/2023 11:33:16] l2tp_core: L2TP core driver, V2.0
[20/02/2023 11:33:16] l2tp_netlink: L2TP netlink interface
[20/02/2023 11:33:16] nss_driver - fw of size 668348  bytes copied to load addr: 40000000, nss_id : 0
[20/02/2023 11:33:16] Supported Frequencies -
[20/02/2023 11:33:16] 748.8 MHz 1.4976 GHz
[20/02/2023 11:33:16] 1.6896 GHz <1>[   16.468855]
[20/02/2023 11:33:16] ffffffbffc651600: meminfo init succeed
[20/02/2023 11:33:16] node size 2 # items 4
[20/02/2023 11:33:16] memory: 40000000 1073741824 (avl 940281856) items 4 active_cores 2
[20/02/2023 11:33:16] ffffffbffc651600: nss core 0 booted successfully
[20/02/2023 11:33:16] nss_driver - fw of size 265248  bytes copied to load addr: 40800000, nss_id : 1
[20/02/2023 11:33:16] Supported Frequencies -
[20/02/2023 11:33:16] 748.8 MHz 1.4976 GHz
[20/02/2023 11:33:16] 1.6896 GHz <1>[   16.531660]
[20/02/2023 11:33:16] ffffffbffc658700: meminfo init succeed
[20/02/2023 11:33:16] sit: IPv6 over IPv4 tunneling driver
[20/02/2023 11:33:16] node size 2 # items 4
[20/02/2023 11:33:16] memory: 40000000 1073741824 (avl 940281856) items 4 active_cores 2
[20/02/2023 11:33:16] ffffffbffc658700: nss core 1 booted successfully
[20/02/2023 11:33:16] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded.
[20/02/2023 11:33:16] gre: GRE over IPv4 demultiplexor driver
[20/02/2023 11:33:16] ip_gre: GRE over IPv4 tunneling driver
[20/02/2023 11:33:16] ip6_gre: GRE over IPv6 tunneling driver
[20/02/2023 11:33:16] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011)
[20/02/2023 11:33:16] QCA multicast snooping installed successfully
[20/02/2023 11:33:16] ip6_tables: (C) 2000-2006 Netfilter Core Team
[20/02/2023 11:33:16] QCA Hy-Fi multicast installation successfully
[20/02/2023 11:33:16] PPP generic driver version 2.4.2
[20/02/2023 11:33:16] nss_lag_init[354]:LAG Manager Installed
[20/02/2023 11:33:16] NET: Registered protocol family 24
[20/02/2023 11:33:16] tntfs: module license 'Commercial. For support email support@tuxera.com.' taints kernel.
[20/02/2023 11:33:16] Disabling lock debugging due to kernel taint
[20/02/2023 11:33:16] Tuxera NTFS driver 3021.4.23.8 [Flags: R/W MODULE].
[20/02/2023 11:33:16] Built against headers 4.4.60 #26 SMP PREEMPT Wed Jul 17 13:35:43 CST 2019 arm64
[20/02/2023 11:33:16] Running on kernel 4.4.60 #1 SMP PREEMPT Wed Sep 29 08:31:14 UTC 2021 aarch64
[20/02/2023 11:33:16] <NSS-CRYPTO>:module loaded Build_ID - 09/29/21, 07:31:58 SoC=ipq807x_64
[20/02/2023 11:33:16] cannot find nss-macsec0 node
[20/02/2023 11:33:16] cannot find nss-macsec1 node
[20/02/2023 11:33:16] cannot find nss-macsec2 node
[20/02/2023 11:33:16] nss_macsec init success
[20/02/2023 11:33:16] diag: IPC Logging disabled
[20/02/2023 11:33:16] hidraw: raw HID events driver (C) Jiri Kosina
[20/02/2023 11:33:16] u32 classifier
[20/02/2023 11:33:16] input device check on
[20/02/2023 11:33:16] Actions configured
[20/02/2023 11:33:16] Mirror/redirect action on
[20/02/2023 11:33:16] pktgen: Packet Generator for packet performance testing. Version: 2.75
[20/02/2023 11:33:16] arp_tables: (C) 2002 David S. Miller
[20/02/2023 11:33:16] Bluetooth: Core ver 2.21
[20/02/2023 11:33:16] NET: Registered protocol family 31
[20/02/2023 11:33:16] Bluetooth: HCI device and connection manager initialized
[20/02/2023 11:33:16] Bluetooth: HCI socket layer initialized
[20/02/2023 11:33:16] Bluetooth: L2CAP socket layer initialized
[20/02/2023 11:33:16] Bluetooth: SCO socket layer initialized
[20/02/2023 11:33:16] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[20/02/2023 11:33:16] Bluetooth: BNEP filters: protocol multicast
[20/02/2023 11:33:16] Bluetooth: BNEP socket layer initialized
[20/02/2023 11:33:16] usbcore: registered new interface driver btusb
[20/02/2023 11:33:16] Ebtables v2.0 registered
[20/02/2023 11:33:16] Bluetooth: HCI UART driver ver 2.3
[20/02/2023 11:33:16] Bluetooth: HCI UART protocol H4 registered
[20/02/2023 11:33:16] Bluetooth: HCI UART protocol BCSP registered
[20/02/2023 11:33:16] Bluetooth: HCI UART protocol ATH3K registered
[20/02/2023 11:33:16] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[20/02/2023 11:33:16] Bluetooth: HIDP socket layer initialized
[20/02/2023 11:33:16] ip_tables: (C) 2000-2006 Netfilter Core Team
[20/02/2023 11:33:16] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[20/02/2023 11:33:16] nf_conntrack_rtsp v0.6.21 loading
[20/02/2023 11:33:17] nf_nat_rtsp v0.6.21 loading
[20/02/2023 11:33:17] PPP MPPE Compression module registered
[20/02/2023 11:33:17] PPTP driver version 0.8.5
[20/02/2023 11:33:17] Bluetooth: RFCOMM TTY layer initialized
[20/02/2023 11:33:17] Bluetooth: RFCOMM socket layer initialized
[20/02/2023 11:33:17] Bluetooth: RFCOMM ver 1.11
[20/02/2023 11:33:17] usbcore: registered new interface driver usblp
[20/02/2023 11:33:17] xt_time: kernel timezone is -0000
[20/02/2023 11:33:17] random: nonblocking pool is initialized
[20/02/2023 11:33:21] configuring additional NSS pbufs
[20/02/2023 11:33:21] additional pbufs of size 9003008 got added to NSS
[20/02/2023 11:33:21] __mm_init_module
[20/02/2023 11:33:21] qdf_dbg_mask value is invalid
[20/02/2023 11:33:21] Using the default module debug levels instead
[20/02/2023 11:33:21] qdf_print_ctrl_register: Allocated print control object 0
[20/02/2023 11:33:21]
[20/02/2023 11:33:21] MINIDUMP VA .bss start=ffffffbffcc23700 module=qdf
[20/02/2023 11:33:21] wlan: [2161:E:CONFIG] cfg_uint_item_handler: 171: gScanProbeRepeatTime=50 - Out of range [0, 30]; Using 50
[20/02/2023 11:33:21]
[20/02/2023 11:33:21] MINIDUMP VA .bss start=ffffffbffcea4080 module=umac
[20/02/2023 11:33:21]
[20/02/2023 11:33:21] MINIDUMP VA .bss start=ffffffbffd047580 module=qca_ol=======ol_if_register_wifi3_0==========
[20/02/2023 11:33:21] wlan: [2186:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:1 with soc_ops:ffffffbffd11bd00
[20/02/2023 11:33:21] remoteproc remoteproc0: powering up q6v5-m3
[20/02/2023 11:33:21] remoteproc remoteproc0: Booting fw image IPQ8074/m3_fw.mdt, size 284
[20/02/2023 11:33:21] Sanity check passed for M3 image
[20/02/2023 11:33:21] remoteproc remoteproc0: remote processor q6v5-m3 is now up
[20/02/2023 11:33:21] wlan: [2186:I:ANY] ol_ath_ahb_ssr: 183: ol_ath_ahb_ssr: SSR event 2
[20/02/2023 11:33:21] <SSR>: glink SUBSYS_BEFOER_POWERUP reinit done
[20/02/2023 11:33:21] remoteproc remoteproc1: powering up q6v5-wcss
[20/02/2023 11:33:21] remoteproc remoteproc1: Booting fw image IPQ8074/q6_fw.mdt, size 668
[20/02/2023 11:33:21] Sanity check passed for the image
[20/02/2023 11:33:22] glink_core_link_up glink is up
[20/02/2023 11:33:22] glink_xprt_open_event
[20/02/2023 11:33:22] Subsystem error monitoring/handling services are up
[20/02/2023 11:33:22] remoteproc remoteproc1: remote processor q6v5-wcss is now up
[20/02/2023 11:33:22] wlan: [2186:I:ANY] ol_ath_ahb_ssr: 183: ol_ath_ahb_ssr: SSR event 3
[20/02/2023 11:33:22] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled
[20/02/2023 11:33:22] cnss: QMI WLFW service connected, state: 0x1
[20/02/2023 11:33:22] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, ffffffbffc87c2c8
[20/02/2023 11:33:22] cnss: device_id : 0xfffe mem mode : [0]
[20/02/2023 11:33:22] cnss: No board_id entry in device tree
[20/02/2023 11:33:22] cnss: BDF location : 0x000000004b0c0000
[20/02/2023 11:33:22] cnss: BDF IPQ8074/bdwlan.bin size 131072
[20/02/2023 11:33:22] cnss: BDF download response , result: 0, err: 0x0
[20/02/2023 11:33:22] cnss: per device BDF location : 0x000000004b0e0000
[20/02/2023 11:33:22] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000
[20/02/2023 11:33:22] cnss: BDF download response , result: 0, err: 0x0
[20/02/2023 11:33:22] wlan: [2186:I:ANY] pld_ahb_wlan_enable: 681: cnss_mode: Cold boot calibration
[20/02/2023 11:33:23] Coldboot calibration wait started
[20/02/2023 11:33:23] Coldboot calibration wait ended
[20/02/2023 11:33:23] wlan: [2186:I:ANY] ol_ath_do_cold_boot_calibration: 467: Coldboot calib successful: radio_id 0x65534
[20/02/2023 11:33:23] cnss: QMI WLFW service disconnected, state: 0x7
[20/02/2023 11:33:23] wlan: [2186:I:ANY] init_ath_pci_3_0: 151: 6ath_ol_pci_wifi3.0:  (Atheros/multi-bss)
[20/02/2023 11:33:23]
[20/02/2023 11:33:23] MINIDUMP VA .bss start=ffffffbffd11c180 module=wifi_3_0
[20/02/2023 11:33:23] wlan: [2193:I:ANY] ol_ath_ahb_ssr: 183: ol_ath_ahb_ssr: SSR event 0
[20/02/2023 11:33:23] remoteproc remoteproc1: stopped remote processor q6v5-wcss
[20/02/2023 11:33:23] wlan: [2193:I:ANY] ol_ath_ahb_ssr: 183: ol_ath_ahb_ssr: SSR event 1
[20/02/2023 11:33:23] glink_core_link_down glink is down
[20/02/2023 11:33:23] <SSR>: glink SUBSYS_AFTER_SHUTDOWN cleanup done
[20/02/2023 11:33:23] remoteproc remoteproc0: stopped remote processor q6v5-m3
[20/02/2023 11:33:23] glink_xprt_close_event
[20/02/2023 11:33:23]
[20/02/2023 11:33:23] MINIDUMP VA .bss start=ffffffbffd23a580 module=qca_ol
[20/02/2023 11:33:23] =======ol_if_register_wifi3_0==========
[20/02/2023 11:33:23] wlan: [2198:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:1 with soc_ops:ffffffbffd30ed00
[20/02/2023 11:33:23] remoteproc remoteproc0: powering up q6v5-m3
[20/02/2023 11:33:23] remoteproc remoteproc0: Booting fw image IPQ8074/m3_fw.mdt, size 284
[20/02/2023 11:33:23] Sanity check passed for M3 image
[20/02/2023 11:33:23] remoteproc remoteproc0: remote processor q6v5-m3 is now up
[20/02/2023 11:33:23] wlan: [2198:I:ANY] ol_ath_ahb_ssr: 183: ol_ath_ahb_ssr: SSR event 2
[20/02/2023 11:33:23] <SSR>: glink SUBSYS_BEFOER_POWERUP reinit done
[20/02/2023 11:33:23] remoteproc remoteproc1: powering up q6v5-wcss
[20/02/2023 11:33:23] remoteproc remoteproc1: Booting fw image IPQ8074/q6_fw.mdt, size 668
[20/02/2023 11:33:23] Sanity check passed for the image
[20/02/2023 11:33:24] glink_core_link_up glink is up
[20/02/2023 11:33:24] glink_xprt_open_event
[20/02/2023 11:33:24] Subsystem error monitoring/handling services are up
[20/02/2023 11:33:24] remoteproc remoteproc1: remote processor q6v5-wcss is now up
[20/02/2023 11:33:24] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled
[20/02/2023 11:33:24] wlan: [2198:I:ANY] ol_ath_ahb_ssr: 183: ol_ath_ahb_ssr: SSR event 3
[20/02/2023 11:33:24] cnss: QMI WLFW service connected, state: 0x1
[20/02/2023 11:33:24] cnss: device_id : 0xfffe mem mode : [0]
[20/02/2023 11:33:24] cnss: No board_id entry in device tree
[20/02/2023 11:33:24] cnss: BDF location : 0x000000004b0c0000
[20/02/2023 11:33:24] cnss: BDF IPQ8074/bdwlan.bin size 131072
[20/02/2023 11:33:24] cnss: BDF download response , result: 0, err: 0x0
[20/02/2023 11:33:24] cnss: per device BDF location : 0x000000004b0e0000
[20/02/2023 11:33:24] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000
[20/02/2023 11:33:24] cnss: BDF download response , result: 0, err: 0x0
[20/02/2023 11:33:24] wlan: [2198:I:ANY] pld_ahb_wlan_enable: 689: cnss_mode: Mission mode
[20/02/2023 11:33:24] wlan: [2198:I:ANY] qca_napi_create: 357: qca_napi_create: napi instance 0 created on pipe 4
[20/02/2023 11:33:24] wlan: [2198:I:ANY] __ol_ath_attach: 3064: Allocated soc ffffffc034d80880
[20/02/2023 11:33:24] btcoex_support 0 wlan_prio_gpio 0
[20/02/2023 11:33:24] wlan: [2198:E:CONFIG] cfg_uint_item_handler: 171: dp_int_timer_threshold_tx=1000 - Out of range [8, 100]; Using 1000
[20/02/2023 11:33:24] wlan: [2198:I:ANY] osif_nss_wifi_soc_setup: 186: nss-wifili:#1 register wifili function for soc
[20/02/2023 11:33:24] wlan: [2198:I:ANY] osif_nss_wifi_soc_setup: 198: nss register id -1 nss config 3 Target Type 18
[20/02/2023 11:33:24] wlan: [2198:I:ANY] __ol_ath_attach: 3278: dev name soc0
[20/02/2023 11:33:24] wlan: [2198:I:ANY] ol_ath_soc_attach: 6591: WMI attached. wmi_handle ffffffc035093000
[20/02/2023 11:33:24] wlan: [2198:I:ANY] htc_wmi_init: 5958: htc_wmi_init() HT Create . ffffffc03627f000
[20/02/2023 11:33:24] wlan: [2198:I:ANY] htc_wmi_init: 5965: htc_wmi_init() Skipping BMI Done.
[20/02/2023 11:33:24] wlan: [2198:I:ANY] htc_wmi_init: 6022: [htc_wmi_init:6022] host_enable 0 nss_nwifi_offload 0
[20/02/2023 11:33:24] wlan: [2198:I:ANY] ol_target_init_complete: 6140: CDP soc attach success
[20/02/2023 11:33:24] wlan: [2198:I:ANY] ol_target_init_complete: 6147: Soc attach success NSS config 0
[20/02/2023 11:33:24] wlan: [2198:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ffffffc03627f000, ep 2, value 1
[20/02/2023 11:33:24] wlan: [2198:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ffffffc03627f000, ep 3, value 1
[20/02/2023 11:33:24] wlan: [167:I:TIF] init_deinit_atf_config_enable: 605: Airtime Fairness: num_peers=1058 num_active_peer=0
[20/02/2023 11:33:24] wlan: [167:I:TIF] HE_CAP Info = 1a08010d
[20/02/2023 11:33:24] wlan: [167:I:TIF] Num HW modes = 2
[20/02/2023 11:33:24] wlan: [167:I:TIF] Num PHY = 3
[20/02/2023 11:33:24] wlan: [167:I:TIF] Preferred HW Mode = 1 Num Radios = 2
[20/02/2023 11:33:24] wlan: [167:I:TIF] init_deinit_add_11ax_modes: 1403: Adding 11ax regulatory modes,
[20/02/2023 11:33:24] wlan: [167:I:TIF] init_deinit_add_11ax_modes: 1406:  phy_id = 0 wireless modes = f97f9001
[20/02/2023 11:33:24] wlan: [167:I:TIF] init_deinit_add_11ax_modes: 1403: Adding 11ax regulatory modes,
[20/02/2023 11:33:24] wlan: [167:I:TIF] init_deinit_add_11ax_modes: 1406:  phy_id = 1 wireless modes = 680680c
[20/02/2023 11:33:24] wlan: [167:I:TIF] init_deinit_add_11ax_modes: 1403: Adding 11ax regulatory modes,
[20/02/2023 11:33:24] wlan: [167:I:TIF] init_deinit_add_11ax_modes: 1406:  phy_id = 2 wireless modes = 397f9001
[20/02/2023 11:33:24] wlan: [167:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 390: dfs_offload 1
[20/02/2023 11:33:24] wlan: [167:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 1038: dfs->dfs_psoc_idx: 0
[20/02/2023 11:33:24] wlan: [167:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 1044: dfs_soc_obj->num_dfs_privs: 1
[20/02/2023 11:33:24] wlan: [167:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 362: Do not allocate DFS object for 2G, pdev_id = 1
[20/02/2023 11:33:24] wlan: [167:I:TIF] init_deinit_update_pdev_tgt_info: 1064: CDP PDEV ATTACH success
[20/02/2023 11:33:24] wlan: [167:I:TIF] init_deinit_update_pdev_tgt_info: 1064: CDP PDEV ATTACH success
[20/02/2023 11:33:24] wlan: [167:I:ANY] copy_fw_abi_version_tlv: 6258: copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0
[20/02/2023 11:33:25] wlan: [167:I:ANY] dp_peer_map_attach_wifi3: 9983: dp_peer_map_attach_wifi3 max_peers 1111, max_ast_index: 4112
[20/02/2023 11:33:25]
[20/02/2023 11:33:25] wlan: [167:I:ANY] ready_extract_init_status_tlv: 8002: ready_extract_init_status_tlv:0
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_connect_htc: 1219: WMI is ready
[20/02/2023 11:33:25] wlan: [2198:E:WMI] wmi_unified_register_event_handler: Event id 37 is unavailable
[20/02/2023 11:33:25] wlan: [2198:E:WMI] wmi_unified_register_event_handler: Event id 141 is unavailable
[20/02/2023 11:33:25] wlan: [2198:E:WMI] wmi_unified_register_event_handler: Event id 137 is unavailable
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_soc_attach: 6665: connect HTC
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_soc_attach: 6666: bypasswmi : 0
[20/02/2023 11:33:25] wlan: [2198:E:WMI] wmi_unified_register_event_handler: Event id 38 is unavailable
[20/02/2023 11:33:25] wlan: [2198:E:WMI] wmi_unified_register_event_handler: Event id 138 is unavailable
[20/02/2023 11:33:25] wlan: [2198:E:WMI] wmi_unified_register_event_handler: Event id 139 is unavailable
[20/02/2023 11:33:25] wlan: [2198:E:WMI] wmi_unified_register_event_handler: Event id 55 is unavailable
[20/02/2023 11:33:25] wlan: [2198:E:WMI] wmi_unified_register_event_handler: Event id 49 is unavailable
[20/02/2023 11:33:25] wlan: [2198:E:WMI] wmi_unified_register_event_handler: Event id 25 is unavailable
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_soc_attach: 6741: ol_ath_soc_attach() UMAC attach .
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ath_lowi_if_netlink_init: 177: ath_lowi_if_netlink_init LOWI Netlink successfully created
[20/02/2023 11:33:25] wlan: [2198:I:ANY] __ol_ath_attach: 3392: pdev_netdev name wifi0
[20/02/2023 11:33:25] wlan: [2198:I:ANY] __ol_ath_attach: 3437: Skip txrx_pdev_attach_target
[20/02/2023 11:33:25] wlan: [2198:I:ANY] __ol_ath_attach: 3461: BURSTING enabled by default
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pdev_attach: 7206: interface_id 0
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pdev_regdmn_init: 6895:  phy id = 0 Modes supported
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pdev_regdmn_init: 6902:  11b = 0 11g = 0 11a = 1 11n = 1 11ac = 1 11ax = 1
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pdev_regdmn_init: 6910:  Reg cap - phy_id = 0 supp_bnd = 2, modes = f97f9001, lo_2g = 0, hi_2g = 0 lo_g5 = 4910, hi_5g = 6000
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_update_wireless_modes: 1318: wireless_modes = f97f9001 before update
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_update_wireless_modes: 1333: Wireless_modes = f97f9001 after update
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_update_ext_caps: 1842: 11ax 5G supported case
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed
[20/02/2023 11:33:25] ieee80211_cbs_init CBS Inited
[20/02/2023 11:33:25] wlan: [2198:I:ANY] acfg_attach: 3457: acfg_attach: 3457: Netlink socket created:ffffffc035090800
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_if_eeprom_attach: 1459: rate power table override is only supported for AR98XX
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_stats_attach: 2071: periodic_chan_stats: 1
[20/02/2023 11:33:25] wlan: [2198:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 25
[20/02/2023 11:33:25] wlan: [0:I:ANY] ol_ath_pdev_attach: 7542: Set global_ic[1], ptr:ffffffbffcea43e8
[20/02/2023 11:33:25] wlan: [0:I:ANY] dp_lag_soc_enable: 88: pdev(ffffffc036f0ce88) Enabling DBDC Repeater 1
[20/02/2023 11:33:25] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 44: pdev(ffffffc036f0ce88) is_primary 1
[20/02/2023 11:33:25] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pdev_attach: 7660: Pdev = 0 Number of peers = 529
[20/02/2023 11:33:25] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 11903: twt enabled.
[20/02/2023 11:33:25]
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_ucfg_set_rx_pkt_protocol_tagging: 1828: Set RX packet type TAG, opcode : 0, pkt_type : 18, metadata : 0xca0,pdev_id = 0, REO dest ring = 5
[20/02/2023 11:33:25]
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 583: ( 1) chan  36 blocked from cfg
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 583: ( 2) chan 132 blocked from cfg
[20/02/2023 11:33:25] wlan: [2198:I:ANY] osif_wrap_attach: 239: osif wrap attached
[20/02/2023 11:33:25]
[20/02/2023 11:33:25] wlan: [2198:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done
[20/02/2023 11:33:25]
[20/02/2023 11:33:25] wlan: [2198:I:ANY] osif_wrap_attach: 247:  Wrap Attached: Wrap_com =ffffffc035090000 ic->ic_wrap_com=ffffffc035090000 &wrap_com->wc_devt=ffffffc035090000
[20/02/2023 11:33:25]
[20/02/2023 11:33:25] wlan: [2198:I:ANY] __ol_ath_attach: 3641: needed_headroom reservation 60
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_enable_fraglist: 2931: Enabled Fraglist bit for the radio wifi0 features 41
[20/02/2023 11:33:25] wlan: [2198:I:ANY] wlan_cfg80211_init: 9619: Number of 5G channels: 25
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ieee80211_cfg80211_radio_attach: 9713: ic: 0xffffffc033b00880, wdev: 0xffffffc033b10a70, wiphy: 0xffffffc0350edaa0, netdev: 0xffffffc033b00000
[20/02/2023 11:33:25] wlan: [2198:I:ANY] __ol_ath_attach: 3392: pdev_netdev name wifi1
[20/02/2023 11:33:25] wlan: [2198:I:ANY] __ol_ath_attach: 3437: Skip txrx_pdev_attach_target
[20/02/2023 11:33:25] wlan: [2198:I:ANY] __ol_ath_attach: 3461: BURSTING enabled by default
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pdev_attach: 7206: interface_id 1
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pdev_regdmn_init: 6895:  phy id = 1 Modes supported
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pdev_regdmn_init: 6902:  11b = 1 11g = 1 11a = 0 11n = 1 11ac = 1 11ax = 1
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pdev_regdmn_init: 6910:  Reg cap - phy_id = 1 supp_bnd = 1, modes = 680680c, lo_2g = 2312, hi_2g = 2732 lo_g5 = 0, hi_5g = 0
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_update_wireless_modes: 1318: wireless_modes = 680680c before update
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_update_wireless_modes: 1333: Wireless_modes = 680680c after update
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_update_ext_caps: 1850: 11ax 2G supported case
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed
[20/02/2023 11:33:25] ieee80211_cbs_init CBS Inited
[20/02/2023 11:33:25] wlan: [2198:I:ANY] acfg_attach: 3432: Offload using existing sock ffffffc035090800
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_if_eeprom_attach: 1459: rate power table override is only supported for AR98XX
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_stats_attach: 2071: periodic_chan_stats: 1
[20/02/2023 11:33:25] wlan: [2198:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 11
[20/02/2023 11:33:25] wlan: [0:I:ANY] ol_ath_pdev_attach: 7542: Set global_ic[2], ptr:ffffffbffcea43e8
[20/02/2023 11:33:25] wlan: [0:I:ANY] dp_lag_soc_enable: 88: pdev(ffffffc0304eda08) Enabling DBDC Repeater 1
[20/02/2023 11:33:25] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 44: pdev(ffffffc0304eda08) is_primary 0
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pdev_attach: 7660: Pdev = 1 Number of peers = 529
[20/02/2023 11:33:25] wlan: [2198:E:WMI] event handler already registered 0x6019
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_ucfg_set_rx_pkt_protocol_tagging: 1828: Set RX packet type TAG, opcode : 0, pkt_type : 18, metadata : 0xca0,pdev_id = 1, REO dest ring = 5
[20/02/2023 11:33:25]
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 583: ( 1) chan  36 blocked from cfg
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 583: ( 2) chan 132 blocked from cfg
[20/02/2023 11:33:25] wlan: [2198:I:ANY] osif_wrap_attach: 239: osif wrap attached
[20/02/2023 11:33:25]
[20/02/2023 11:33:25] wlan: [2198:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done
[20/02/2023 11:33:25]
[20/02/2023 11:33:25] wlan: [2198:I:ANY] osif_wrap_attach: 247:  Wrap Attached: Wrap_com =ffffffc029d56800 ic->ic_wrap_com=ffffffc029d56800 &wrap_com->wc_devt=ffffffc029d56800
[20/02/2023 11:33:25]
[20/02/2023 11:33:25] wlan: [2198:I:ANY] __ol_ath_attach: 3641: needed_headroom reservation 60
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ol_ath_enable_fraglist: 2931: Enabled Fraglist bit for the radio wifi1 features 41
[20/02/2023 11:33:25] wlan: [2198:I:ANY] wlan_cfg80211_init: 9607: Number of 2G channels: 11
[20/02/2023 11:33:25] wlan: [2198:I:ANY] ieee80211_cfg80211_radio_attach: 9713: ic: 0xffffffc033b40880, wdev: 0xffffffc033b50a70, wiphy: 0xffffffc029b002a0, netdev: 0xffffffc033b40000
[20/02/2023 11:33:25] wlan: [2198:I:ANY] wlan_pdev_operation: 729: num_radios=1, wifi_radios[0].sc = ffffffc033b00880_radio_type = 2
[20/02/2023 11:33:25] wlan: [2198:I:ANY] wlan_pdev_operation: 729: num_radios=2, wifi_radios[1].sc = ffffffc033b40880_radio_type = 2
[20/02/2023 11:33:25] wlan: [2198:I:ANY] init_ath_pci_3_0: 151: 6ath_ol_pci_wifi3.0:  (Atheros/multi-bss)
[20/02/2023 11:33:25]
[20/02/2023 11:33:25] MINIDUMP VA .bss start=ffffffbffd30f180 module=wifi_3_0
[20/02/2023 11:33:25] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[20/02/2023 11:33:25] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 11903: twt enabled.
[20/02/2023 11:33:25]
[20/02/2023 11:33:25] wlan: [2202:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:0 with soc_ops:ffffffbffd3a8558
[20/02/2023 11:33:25] wlan: [2202:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:0 with soc_ops:ffffffbffd3a8558
[20/02/2023 11:33:25] wlan: [2202:I:ANY] init_ath_pci_2_0: 143: 6ath_ol_pci_2_0:  (Atheros/multi-bss)
[20/02/2023 11:33:26] FAT-fs (sdb1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
[20/02/2023 11:33:26] ntfs: (device sdb1): parse_options(): Option iocharset is deprecated. Please use option nls=<charsetname> in the future.
[20/02/2023 11:33:26] tntfs warning (device sdb1, pid 2519): parse_options(): Disabling default option utf8 and enabling option nls=utf8.  This means that Emojis and other extended Unicode characters in filenames will not work.  Do not specify nls=utf8 option to fix this.
[20/02/2023 11:33:26] tntfs info (device sdb1, pid 2519): ntfs_fill_super(): fail_safe is enabled.
[20/02/2023 11:33:26] tntfs info (device sdb1, pid 2545): ntfs_fill_super(): fail_safe is enabled.
[20/02/2023 11:33:41] EXT4-fs (mmcblk0p11): mounted filesystem with ordered data mode. Opts: commit=1
[20/02/2023 11:33:41] EXT4-fs (mmcblk0p10): mounted filesystem with ordered data mode. Opts: commit=1
[20/02/2023 11:33:42] ECM init
[20/02/2023 11:33:42] ECM database jhash random seed: 0xa550eda5
[20/02/2023 11:33:42] ECM init complete
[20/02/2023 11:33:42] device eth0 entered promiscuous mode
[20/02/2023 11:33:42] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready
[20/02/2023 11:33:42] device eth1 entered promiscuous mode
[20/02/2023 11:33:42] br-lan: port 2(eth1) entered forwarding state
[20/02/2023 11:33:42] br-lan: port 2(eth1) entered forwarding state
[20/02/2023 11:33:42] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready
[20/02/2023 11:33:42] device eth2 entered promiscuous mode
[20/02/2023 11:33:42] br-lan: port 3(eth2) entered forwarding state
[20/02/2023 11:33:42] br-lan: port 3(eth2) entered forwarding state
[20/02/2023 11:33:43] device eth3 entered promiscuous mode
[20/02/2023 11:33:43] br-lan: port 4(eth3) entered forwarding state
[20/02/2023 11:33:43] br-lan: port 4(eth3) entered forwarding state
[20/02/2023 11:33:43] device eth5 entered promiscuous mode
[20/02/2023 11:33:43] br-lan: port 5(eth5) entered forwarding state
[20/02/2023 11:33:43] br-lan: port 5(eth5) entered forwarding state
[20/02/2023 11:33:43] eth0: PHY Link up speed: 1000
[20/02/2023 11:33:43] eth3: PHY Link up speed: 1000
[20/02/2023 11:33:43] br-lan: port 1(eth0) entered forwarding state
[20/02/2023 11:33:43] br-lan: port 1(eth0) entered forwarding state
[20/02/2023 11:33:43] br-lan: port 2(eth1) entered disabled state
[20/02/2023 11:33:43] br-lan: port 3(eth2) entered disabled state
[20/02/2023 11:33:43] __mc_netlink_receive: Disable bridge snooping!
[20/02/2023 11:33:43] br-lan: port 5(eth5) entered disabled state
[20/02/2023 11:33:43] __mc_netlink_receive: Disable bridge snooping!
[20/02/2023 11:33:44] wlan: [3822:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 13
[20/02/2023 11:33:44] wlan: [3822:I:ANY] number of channels: 2G = 13 5G = 0
[20/02/2023 11:33:44] wlan: [3837:I:ANY] wlan_cfg80211_set_hwaddr: 5439: wlan_cfg80211_set_hwaddr :bc:cf:4f:ff:1b:a2 ret: 0
[20/02/2023 11:33:44] wlan: [3839:I:ANY] ol_ath_set_config_param: 1493: set TXBF_SND_PERIOD: value 100 wmi_status 0
[20/02/2023 11:33:44] wlan: [0:I:ANY] dp_lag_soc_enable: 88: pdev(ffffffc0304eda08) Enabling DBDC Repeater 0
[20/02/2023 11:33:44] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[20/02/2023 11:33:44] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[20/02/2023 11:33:44] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[20/02/2023 11:33:44] wlan: [0:I:ANY] ol_ath_set_config_param: 2209: Disconnect_timeout value: 10
[20/02/2023 11:33:44] wlan: [0:I:ANY] ol_ath_set_config_param: 2215: Reconfiguration_timeout value:60
[20/02/2023 11:33:45] br-lan: port 4(eth3) entered forwarding state
[20/02/2023 11:33:45] br-lan: port 1(eth0) entered forwarding state
[20/02/2023 11:33:45] wlan: [4180:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 19
[20/02/2023 11:33:45] wlan: [4180:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 979: freq=58
[20/02/2023 11:33:45] wlan: [4180:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 979: freq=106
[20/02/2023 11:33:45] wlan: [4180:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 979: freq=122
[20/02/2023 11:33:45] wlan: [4180:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 19
[20/02/2023 11:33:45] wlan: [4180:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 979: freq=58
[20/02/2023 11:33:45] wlan: [4180:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 979: freq=106
[20/02/2023 11:33:45] wlan: [4180:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_init_precac_list: 979: freq=122
[20/02/2023 11:33:45] wlan: [4180:I:ANY] number of channels: 2G = 0 5G = 19
[20/02/2023 11:33:45] wlan: [3522:I:ANY] ol_acfg_handle_wifi_ioctl: 417: ol_acfg_handle_wifi_ioctl: req->cmd=75 not valid for radio interface, it's for VAP
[20/02/2023 11:33:45] wlan: [4198:I:ANY] wlan_cfg80211_set_hwaddr: 5439: wlan_cfg80211_set_hwaddr :bc:cf:4f:ff:1b:a3 ret: 0
[20/02/2023 11:33:45] wlan: [4200:I:ANY] ol_ath_set_config_param: 1493: set TXBF_SND_PERIOD: value 100 wmi_status 0
[20/02/2023 11:33:45] wlan: [0:I:ANY] dp_lag_soc_enable: 88: pdev(ffffffc036f0ce88) Enabling DBDC Repeater 0
[20/02/2023 11:33:45] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[20/02/2023 11:33:45] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[20/02/2023 11:33:45] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed
[20/02/2023 11:33:45] wlan: [0:I:ANY] ol_ath_set_config_param: 2209: Disconnect_timeout value: 10
[20/02/2023 11:33:45] wlan: [0:I:ANY] ol_ath_set_config_param: 2215: Reconfiguration_timeout value:60
[20/02/2023 11:33:48] eth0: PHY Link is down
[20/02/2023 11:33:48] eth3: PHY Link is down
[20/02/2023 11:33:48] br-lan: port 1(eth0) entered disabled state
[20/02/2023 11:33:48] br-lan: port 4(eth3) entered disabled state
[20/02/2023 11:33:50] eth0: PHY Link up speed: 1000
[20/02/2023 11:33:50] br-lan: port 1(eth0) entered forwarding state
[20/02/2023 11:33:50] br-lan: port 1(eth0) entered forwarding state
[20/02/2023 11:33:50] eth3: PHY Link up speed: 1000
[20/02/2023 11:33:50] br-lan: port 4(eth3) entered forwarding state
[20/02/2023 11:33:50] br-lan: port 4(eth3) entered forwarding state
[20/02/2023 11:33:52] br-lan: port 1(eth0) entered forwarding state
[20/02/2023 11:33:52] br-lan: port 4(eth3) entered forwarding state
[20/02/2023 11:33:53] __mc_netlink_receive: Disable bridge snooping!
[20/02/2023 11:33:59] Bluetooth: Out-of-order packet arrived, got 1 expected 0
[20/02/2023 11:34:03] __mc_netlink_receive: Enable bridge snooping!
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=bootipq
bootdelay=2
boxid=xxxxxxxxxxxxxxxx
countrycode=E1
defenv=sf probe && sf erase 0x600000 0x10000
ethact=eth0
ethaddr=BC:CF:4F:XX:XX:X0
fdt_high=0x4A400000
fdtcontroladdr=4a9674b0
flash_type=8
fwimg=norplusemmc-ipq807x_64-single.100ABSK3C0.imgroot@NBG7815:~# fw_printenv
baudrate=115200
bootargs=console=ttyMSM0,115200n8
bootcmd=bootipq
bootdelay=2
boxid=xxxxxxxxxxxxxxxx
countrycode=E1
defenv=sf probe && sf erase 0x600000 0x10000
ethact=eth0
ethaddr=BC:CF:4F:XX:XX:X0
fdt_high=0x4A400000
fdtcontroladdr=4a9674b0
flash_type=8
fwimg=norplusemmc-ipq807x_64-single.100ABSK3C0.img
ipaddr=192.168.1.1
ledB=run ledinit && i2c mw 0x40 0x18 0xff && i2c mw 0x40 0x1b 0xff && i2c mw 0x40 0x1e 0xff
ledG=run ledinit && i2c mw 0x40 0x17 0xff && i2c mw 0x40 0x1a 0xff && i2c mw 0x40 0x1d 0xff
ledR=run ledinit && i2c mw 0x40 0x16 0xff && i2c mw 0x40 0x19 0xff && i2c mw 0x40 0x1c 0xff
ledRblink=i2c mw 0x40 0x16 0xff && i2c mw 0x40 0x19 0xff && i2c mw 0x40 0x1c 0xff && sleep 1 && i2c mw 0x40 0x16 0x00 && i2c mw 0x40 0x19 0x00 && i2c mw 0x40 0x1c 0x00 && sleep 1
ledallon=run ledinit && mw 0x44000000 ffffffff 3 && i2c write 0x44000000 0x32 0x16 9 && i2c write 0x44000000 0x35 0x16 9
ledinit=i2c dev 0 && i2c probe && i2c mw 0x40 0x0 0x40 && mw 0x44000000 a0a0a0a0 3 && i2c write 0x44000000 0x40 0x7 9 && mw 0x44000000 00000000 3 && i2c write 0x44000000 0x40 0x16 9
machid=80100f1
netmask=255.255.255.0
partno=NBG7815-EU0102F
preboot=dcache off
progimg=aq_load_fw 8 && tftpboot 0x44000000 $fwimg && imgaddr=0x44000000 && source $imgaddr:script && reset
progzyxelimg=setenv machid 80100f1 && setenv bootcmd bootipq && saveenv && aq_load_fw 8 && tftpboot 0x44000000 $fwimg && imgaddr=0x44000000 && source $imgaddr:script && reset
serialnum=xxxxxxxxxxxxxxxx
serverip=192.168.1.99
soc_version_major=2
soc_version_minor=0
stderr=serial@78B3000
stdin=serial@78B3000
stdout=serial@78B3000
readonly=ro
ipaddr=192.168.1.1
ledB=run ledinit && i2c mw 0x40 0x18 0xff && i2c mw 0x40 0x1b 0xff && i2c mw 0x40 0x1e 0xff
ledG=run ledinit && i2c mw 0x40 0x17 0xff && i2c mw 0x40 0x1a 0xff && i2c mw 0x40 0x1d 0xff
ledR=run ledinit && i2c mw 0x40 0x16 0xff && i2c mw 0x40 0x19 0xff && i2c mw 0x40 0x1c 0xff
ledRblink=i2c mw 0x40 0x16 0xff && i2c mw 0x40 0x19 0xff && i2c mw 0x40 0x1c 0xff && sleep 1 && i2c mw 0x40 0x16 0x00 && i2c mw 0x40 0x19 0x00 && i2c mw 0x40 0x1c 0x00 && sleep 1
ledallon=run ledinit && mw 0x44000000 ffffffff 3 && i2c write 0x44000000 0x32 0x16 9 && i2c write 0x44000000 0x35 0x16 9
ledinit=i2c dev 0 && i2c probe && i2c mw 0x40 0x0 0x40 && mw 0x44000000 a0a0a0a0 3 && i2c write 0x44000000 0x40 0x7 9 && mw 0x44000000 00000000 3 && i2c write 0x44000000 0x40 0x16 9
machid=80100f1
netmask=255.255.255.0
partno=NBG7815-EU0102F
preboot=dcache off
progimg=aq_load_fw 8 && tftpboot 0x44000000 $fwimg && imgaddr=0x44000000 && source $imgaddr:script && reset
progzyxelimg=setenv machid 80100f1 && setenv bootcmd bootipq && saveenv && aq_load_fw 8 && tftpboot 0x44000000 $fwimg && imgaddr=0x44000000 && source $imgaddr:script && reset
serialnum=xxxxxxxxxxxxxxxx
serverip=192.168.1.99
soc_version_major=2
soc_version_minor=0
stderr=serial@78B3000
stdin=serial@78B3000
stdout=serial@78B3000
readonly=ro
This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/10/31 16:24
  • by pwned