Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| inbox:toh:xiaomi:mi_wifi_range_extender_ac1200_model_ra75 [2022/12/17 07:03] – Corrected tag "wallplug" to "wall_plug" hardfalcon | inbox:toh:xiaomi:mi_wifi_range_extender_ac1200_model_ra75 [2024/05/01 20:03] – [Debricking] jdeisenh | ||
|---|---|---|---|
| Line 1: | Line 1: | ||
| ====== Xiaomi Mi WiFi Range Extender AC1200 Model RA75 ====== | ====== Xiaomi Mi WiFi Range Extender AC1200 Model RA75 ====== | ||
| - | This is compact, wall-wart type range extender with 2x2 Wifi5 Dual band hardware. 20€ in 2022 in Germany, taxes included. | + | {{: |
| + | |||
| + | This is a compact, wall-wart type range extender with 2x2 Wifi5 dual band hardware. 20€ in 2022 in Germany, taxes included. | ||
| Installation is done through an app, there is no HTML UI. | Installation is done through an app, there is no HTML UI. | ||
| - | If you don't mind some soldering, this is a very capable hardware for the price that runs openwrt | + | If you don't mind some soldering, this is a very capable hardware for the price that runs OpenWrt |
| - | Major hardware | + | Major hardware |
| - | {{:media: | + | Warning: There is a newer version on the market, Model RC04. This looks identical, but is quite a bit harder to install. Avoid. |
| - | ===== OpenWrt support | + | ===== Supported Versions |
| + | <!-- ToH: { | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | } --> | ||
| - | This is almost the same hardware as [[: | + | Supported in snapshots, since 2023-01-14. |
| - | Note: Make sure to use the firmware of the chinese version linked above, not the ' | + | |
| - | Somewhat cleaner support is available as a patch, but currently stuck in the merge pipeline for lack of reviewers. | ||
| This box does not run a HTML UI, it is configured through an app. For this reason, you cannot use OpenWrtInvasion. | This box does not run a HTML UI, it is configured through an app. For this reason, you cannot use OpenWrtInvasion. | ||
| You have to install it by opening the box, soldering an UART connector, connect an UART 3V Interface, flash via shell and TFTP. | You have to install it by opening the box, soldering an UART connector, connect an UART 3V Interface, flash via shell and TFTP. | ||
| + | |||
| + | This is almost the same hardware as [[: | ||
| Please note that right now, there is no way back to the stock firmware. (For lack of trying, and why would anybody?) | Please note that right now, there is no way back to the stock firmware. (For lack of trying, and why would anybody?) | ||
| - | ===== Supporting activities ===== | ||
| - | OpenWrt forum thread: https:// | + | There seems to be a new version available from 2023 'Model RC04' with a different wifi chip. This is almost |
| + | ** Supporting activities ** | ||
| - | ===== Experimental firmware ===== | + | OpenWrt forum thread: https:// |
| - | Use the firmware from [[:toh:xiaomi:mi_router_4a_mir4a_100m]] | + | ===== Hardware Highlights ===== |
| - | As with other 'wall wart' type devices, you will end up with the only ethernet port being the WAN port, which does not allow you to access the device. | + | <!-- ToH: { |
| - | You have to change this to a LAN port on the serial console. | + | " |
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | " | ||
| + | } --> | ||
| - | ===== Hardware highlights | + | ===== Installation |
| - | ^ CPU ^ Ram ^ Flash ^ Network | + | <!-- ToH: { |
| - | | MT7628DAN @ 580 MHz | 64 MiB | 16 MiB | 1x 100 | b/g/n/ac 2x2 Dual band | no | Yes | ? | | + | " |
| + | " | ||
| + | " | ||
| + | " | ||
| + | | ||
| + | " | ||
| + | } --> | ||
| + | ** Alternative firmware ** | ||
| + | If you must or want to run a pre-2022 release version, you can use the one for mi-router-4a-100m. | ||
| + | Warning: (*not* mi-router-4a-100m-intl). | ||
| + | Buttons and LED definitions are wrong, and the LAN interface does not exist, the only ethernet is the WAN interface). | ||
| + | It follows that you have to disable the firewall or adjust the network config from the serial console, otherwise the device will be inacessible. | ||
| - | ===== Installation ===== | ||
| - | /* | ||
| - | - → [[: | ||
| - | - → [[docs: | ||
| - | - → [[: | ||
| - | */ | ||
| ==== Installing OpenWrt ==== | ==== Installing OpenWrt ==== | ||
| - | Only known way to install *right now* is open the box, solder | + | Only known way to install *right now* is the old school way of opening |
| + | There is one screw under the barcode, right side. Header is standard. See FCC DB for photos. | ||
| From there, its rather easy: | From there, its rather easy: | ||
| Line 62: | Line 85: | ||
| -> [[docs: | -> [[docs: | ||
| - | As long as you haven' | + | The standard method of debricking common to xiaomi devices |
| - | /*** if info available: uncomment and fill in | ||
| ===== Failsafe mode ===== | ===== Failsafe mode ===== | ||
| -> [[docs: | -> [[docs: | ||
| - | ***/ | ||
| + | Use the hidden reset button near the ethernet connector for failsafe mode, when the led starts blinking fast. The big WPS button on the front doesn' | ||
| Line 145: | Line 167: | ||
| - | There is a single screw under the barcode label, right side. Removing the screw beneath, you can split the unit into the power supply and the wifi part. | + | There is a single screw under the barcode label, right side. Removing the screw beneath, you can split the unit into the power supply and the wifi part. The ' |
| + | {{: | ||
| ==== Serial ==== | ==== Serial ==== | ||
| -> [[docs: | -> [[docs: | ||
| Line 859: | Line 882: | ||
| ===== Tags ===== | ===== Tags ===== | ||
| - | {{tag> | + | {{tag> |