Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
inbox:toh:wudoumi:wudoumi_wdm-k10_rev5 [2023/09/17 15:00] – [Flash Layout] cyrevoltinbox:toh:wudoumi:wudoumi_wdm-k10_rev5 [2023/09/17 17:34] – [Opening the case] cyrevolt
Line 13: Line 13:
 <color orange>**work in progress :)**</color> <color orange>**work in progress :)**</color>
  
 +see [[https://github.com/orangecms/ubis-openwrt/tree/wudoumi-k10]]
  
 /*** if info available: uncomment and fill in /*** if info available: uncomment and fill in
Line 82: Line 83:
 | vlan1 (eth0.1)   | WAN port      |     DHCP               | | vlan1 (eth0.1)   | WAN port      |     DHCP               |
 | wl0              | WiFi          |     Enabled            | | wl0              | WiFi          |     Enabled            |
-</WRAP> 
  
  
-/*** if info available: uncomment and fill in 
 ==== Buttons ==== ==== Buttons ====
 -> [[docs:guide-user:hardware:hardware.button]] on howto use and configure the hardware button(s). -> [[docs:guide-user:hardware:hardware.button]] on howto use and configure the hardware button(s).
Line 96: Line 95:
 | Power-on  |  power-on / charge check  | | Power-on  |  power-on / charge check  |
 </WRAP> </WRAP>
-***/ 
- 
  
 ===== Hardware ===== ===== Hardware =====
Line 119: Line 116:
 Please check out the article [[docs:techref:flash.layout|Flash layout]]. It contains examples and explanations that describe how to document the flash layout. Please check out the article [[docs:techref:flash.layout|Flash layout]]. It contains examples and explanations that describe how to document the flash layout.
  
-  WDM-K10  Flash Layout stock firmware      ^^^^^^ + WDM-K10  Flash Layout                                                                                                                                                      ||||||| 
-^ Layer0                             W25Q64BV spi0.0: W25Q64BV      8192KiB      ||||| +^ Layer0                   W25Q64BV spi0.0: W25Q64BV      8192KiB                                                                                                            |||||| 
-^ Layer1       |  mtd0 **//u-boot//** 192KiB    mtd1 **//u-boot env//** 64KiB    | mtd2 **//factory//** 64KiB  |||  mtd3 **//kernel uimage//** 7872KiB +^ Layer1                  |  mtd0 **//u-boot//** 192KiB               mtd1 **//u-boot env//** 64KiB  | mtd2 **//factory//** 64KiB        |||  mtd3 **//kernel uimage//** 7872KiB 
-^ mountpoint   |  none                        |  none                              | none                        |||  /                                   | +^ mountpoint              |  none                                    |  none                           | none                              |||  /                                   | 
-^ filesystem   |  none                        |  none                              | none                        |||  initramfs                           |+^ filesystem              |  none                                    |  none                           | none                              |||  initramfs or something?             |
  
 </WRAP> </WRAP>
Line 129: Line 126:
 ==== Photos ==== ==== Photos ====
  
-{{ media:wdm-k10_stickered.jpg?200|Wudoumi WDM-K10}} +{{media:wudoumi:wdm-k10:wdm-k10_covers-removed.jpg?360|covers removed}} 
- +{{media:wdm-k10_pcb-sandwich.jpg?360|3 PCBs and battery side view}} 
-{{ media:wudoumi:wdm-k10:wdm-k10_covers-removed.jpg?300|covers removed}} +{{media:wdm-k10_case-open.jpg?360|case open, PCB out}}
- +
-{{ media:wdm-k10_pcb-sandwich.jpg?400|3 PCBs and battery side view}} +
- +
-<WRAP clear/> +
-{{ media:wdm-k10_case-open.jpg?400|case open, PCB out}}+
  
  
 ==== Opening the case ==== ==== Opening the case ====
 +
 +| {{:meta:icons:tango:48px-emblem-important.svg.png?nolink}} | Keep in mind that the battery is always attached, so be very careful with the PCB when using tools and working on it to avoid damage. |
  
 <WRAP BOX> <WRAP BOX>
 The case can be easily opened using plastic tools. Best start next to the WiFi icon above the LEDs, and go all around to detach the top cover. The case can be easily opened using plastic tools. Best start next to the WiFi icon above the LEDs, and go all around to detach the top cover.
  
-The bigger bottom part is held by four screws. Flip the device, then pull up the cover.+The bigger bottom part is held by four screws. Remove them, flip the device, then pull up the cover off.
  
 From now on, "bottom" refers to the side holding the battery and the boards. From now on, "bottom" refers to the side holding the battery and the boards.
Line 161: Line 155:
 The UART RX and TX pins are as marked in the photo. The UART RX and TX pins are as marked in the photo.
 </WRAP> </WRAP>
 +
 +If you want to access the UART, you will need to solder wires. Since there are so many ports you may not need, you can route them out e.g. through the compact flash card slot.
  
 ^ Serial connection parameters\\ for Wudoumi WDM-K10 | 57600, 8N1 | ^ Serial connection parameters\\ for Wudoumi WDM-K10 | 57600, 8N1 |
Line 170: Line 166:
 ==== OEM bootlog ==== ==== OEM bootlog ====
 <WRAP bootlog> <WRAP bootlog>
-TODO+<nowiki> 
 +[04020D09][04020C0E] 
 +DDR Calibration DQS reg = 00008889 
 + 
 + 
 +U-Boot 1.1.3 (Nov 12 2016 - 18:49:00) 
 + 
 +Board: Ralink APSoC DRAM:  64 MB 
 +relocate_code Pointer at: 83fb8000 
 +****************************** 
 +Software System Reset Occurred 
 +****************************** 
 +flash manufacture id: ef, device id 40 17 
 +find flash: W25Q64BV 
 +============================================  
 +Ralink UBoot Version: 4.3.0.0 
 +--------------------------------------------  
 +ASIC 7628_MP (Port5<->None) 
 +DRAM component: 512 Mbits DDR, width 16 
 +DRAM bus: 16 bit 
 +Total memory: 64 MBytes 
 +Flash component: SPI Flash 
 +Date:Nov 12 2016  Time:18:49:00 
 +============================================  
 +icache: sets:512, ways:4, linesz:32 ,total:65536 
 +dcache: sets:256, ways:4, linesz:32 ,total:32768  
 + 
 + ##### The CPU freq = 575 MHZ ####  
 + estimate memory size =64 Mbytes 
 +RESET MT7628 PHY!!!!!! 
 +Please choose the operation:  
 +   1: Load system code to SDRAM via TFTP.  
 +   2: Load system code then write to Flash via TFTP.  
 +   3: Boot system code via Flash (default). 
 +   4: Entr boot command line interface. 
 +   7: Load Boot Loader code then write to Flash via Serial.  
 +   9: Load Boot Loader code then write to Flash via TFTP.  
 + 4  3  2  1  0  
 +    
 +3: System Boot system code via Flash. 
 +## Booting image at bc050000 ... 
 +   Image Name:   Linux Kernel Image 
 +   Image Type:   MIPS Linux Kernel Image (lzma compressed) 
 +   Data Size:    7149886 Bytes =  6.8 MB 
 +   Load Address: 80000000 
 +   Entry Point:  8000c150 
 +   Verifying Checksum ... OK 
 +   Uncompressing Kernel Image ... OK 
 +No initrd 
 +## Transferring control to Linux (at address 8000c150) ... 
 +## Giving linux memsize in MB, 64 
 + 
 +Starting kernel ... 
 + 
 + 
 +LINUX started... 
 + 
 + THIS IS ASIC 
 +Linux version 2.6.36 (root@jimith--machine) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #740 Mon Dec 18 03:53:21 CST 2017 
 + 
 + The CPU feqenuce set to 575 MHz 
 + 
 + MIPS CPU sleep mode enabled. 
 +CPU revision is: 00019655 (MIPS 24Kc) 
 +Software DMA cache coherency 
 +Determined physical RAM map: 
 + memory: 04000000 @ 00000000 (usable) 
 +Initrd not found or empty - disabling initrd 
 +Zone PFN ranges: 
 +  Normal   0x00000000 -> 0x00004000 
 +Movable zone start PFN for each node 
 +early_node_map[1] active PFN ranges 
 +    0: 0x00000000 -> 0x00004000 
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256 
 +Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0 
 +PID hash table entries: 256 (order: -2, 1024 bytes) 
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) 
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) 
 +Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes. 
 +Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes 
 +Writing ErrCtl register=000797e0 
 +Readback ErrCtl register=000797e0 
 +Memory: 53732k/65536k available (4538k kernel code, 11768k reserved, 1275k data, 5108k init, 0k highmem) 
 +NR_IRQS:128 
 +console [ttyS1] enabled 
 +Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) 
 +pid_max: default: 32768 minimum: 301 
 +Mount-cache hash table entries: 512 
 +NET: Registered protocol family 16 
 +RALINK_GPIOMODE = 54154445  
 +RALINK_GPIOMODE = 54144445  
 +***** Xtal 40MHz ***** 
 +start PCIe register access 
 +RALINK_RSTCTRL = 2400000 
 +RALINK_CLKCFG1 = fdbfffc0 
 + 
 +*************** MT7628 PCIe RC mode ************* 
 +PCIE0 no card, disable it(RST&CLK) 
 +bio: create slab <bio-0> at 0 
 +vgaarb: loaded 
 +SCSI subsystem initialized 
 +usbcore: registered new interface driver usbfs 
 +usbcore: registered new interface driver hub 
 +usbcore: registered new device driver usb 
 +cfg80211: Calling CRDA to update world regulatory domain 
 +Switching to clocksource Ralink Systick timer 
 +NET: Registered protocol family 2 
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes) 
 +TCP established hash table entries: 2048 (order: 2, 16384 bytes) 
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes) 
 +TCP: Hash tables configured (established 2048 bind 2048) 
 +TCP reno registered 
 +UDP hash table entries: 256 (order: 0, 4096 bytes) 
 +UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) 
 +NET: Registered protocol family 1 
 +RT3xxx EHCI/OHCI init. 
 +NTFS driver 2.1.29 [Flags: R/W]. 
 +exFAT: Version 1.2.6 
 +fuse init (API version 7.15) 
 +msgmni has been set to 104 
 +Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) 
 +io scheduler noop registered (default) 
 +doit 
 +Ralink gpio driver initialized 
 +Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled 
 +serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A 
 +serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A 
 +brd: module loaded 
 +Loading iSCSI transport class v2.0-870. 
 +osst :I: Tape driver with OnStream support version 0.99.4 
 +osst :I: $Id: //WIFI_SOC/MP/SDK_4_3_0_0/RT288x_SDK/source/linux-2.6.36.x/drivers/scsi/osst.c#1 $ 
 +SCSI Media Changer driver v0.25  
 +flash manufacture id: ef, device id 40 17 
 +W25Q64BV(ef 40170000) (8192 Kbytes) 
 +mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 
 +Creating 5 MTD partitions on "raspi": 
 +0x000000000000-0x000000800000 : "ALL" 
 +0x000000000000-0x000000030000 : "Bootloader" 
 +0x000000030000-0x000000040000 : "Config" 
 +0x000000040000-0x000000050000 : "Factory" 
 +0x000000050000-0x000001000000 : "Kernel" 
 +mtd: partition "Kernel" extends beyond the end of device "raspi" -- size truncated to 0x7b0000 
 +rdm_major = 253 
 +GMAC1_MAC_ADRH -- : 0x0000009a 
 +GMAC1_MAC_ADRL -- : 0xd5515246 
 +Ralink APSoC Ethernet Driver Initilization. v3.1  256 rx/tx descriptors allocated, mtu = 1500! 
 +GMAC1_MAC_ADRH -- : 0x0000009a 
 +GMAC1_MAC_ADRL -- : 0xd5515246 
 +PROC INIT OK! 
 +PPP generic driver version 2.4.2 
 +PPP Deflate Compression module registered 
 +PPP BSD Compression module registered 
 +PPP MPPE Compression module registered 
 +NET: Registered protocol family 24 
 +PPTP driver version 0.8.5 
 +IMQ driver loaded successfully. 
 + Hooking IMQ after NAT on PREROUTING. 
 + Hooking IMQ before NAT on POSTROUTING. 
 + 
 + 
 +=== pAd = c0147000, size = 1459768 === 
 + 
 +<-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x 
 +<-- RTMPAllocAdapterBlock, Status=0 
 +RtmpChipOpsHook(492): Not support for HIF_MT yet! 
 +mt7628_init()--> 
 +mt7628_init(FW(8a00), HW(8a01), CHIPID(7628)) 
 +e2.bin mt7628_init(1135)::(2), pChipCap->fw_len(63888) 
 +mt_bcn_buf_init(218): Not support for HIF_MT yet! 
 +<--mt7628_init() 
 +Netfilter messages via NETLINK v0.30. 
 +nf_conntrack version 0.5.0 (839 buckets, 3356 max) 
 +ctnetlink v0.93: registering with nfnetlink. 
 +matchsize=264 
 +xt_time: kernel timezone is -0000 
 +IPVS: Registered protocols (TCP, UDP, SCTP, AH, ESP) 
 +IPVS: Connection hash table configured (size=4096, memory=32Kbytes) 
 +IPVS: ipvs loaded. 
 +IPv4 over IPv4 tunneling driver 
 +GRE over IPv4 demultiplexor driver 
 +gre: can't add protocol 
 +GRE over IPv4 tunneling driver 
 +ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone 
 +ipt_CLUSTERIP: ClusterIP Version 0.8 loaded successfully 
 +arp_tables: (C) 2002 David S. Miller 
 +TCP cubic registered 
 +NET: Registered protocol family 10 
 +NET: Registered protocol family 17 
 +L2TP core driver, V2.0 
 +PPPoL2TP kernel driver, V2.0 
 +802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> 
 +All bugs added by David S. Miller <davem@redhat.com> 
 +Warning: unable to open an initial console. 
 +Freeing unused kernel memory: 5108k freed 
 +Algorithmics/MIPS FPU Emulator v1.5 
 +Welcome to 
 +     __   ___  _____  _____    _______ ______  _____  _   ___ 
 +    |  \ /   ||  ___||  __ \ | ||  __  ||__  __||  ___|| | /  / 
 +    |      || |__  | |  \ \| || |  | |  | |   | |__  | |/  / 
 +    |  | |   ||  ___|| |  | || || |__| |  | |    ___||    \ 
 +    |  | |   || |___ | |__/ /| ||  __  |  | |   | |___ | |\  \ 
 +    |__| |___||_____||_____/ |_||_|  |_|  |_|   |_____||_| \__\ 
 + 
 +         = Everyday Genius = 
 +              
 +init: can't log to /dev/tty5 
 +starting pid 136, tty '/dev/ttyS1': '/bin/sh' 
 + 
 + 
 +BusyBox v1.12.1 (2015-06-26 10:56:45 CST) built-in shell (ash) 
 +Enter 'help' for a list of built-in commands. 
 + 
 +# TX_BCN DESC a211e000 size = 320 
 +RX[0] DESC a2121000 size = 1024 
 +RX[1] DESC a2122000 size = 1024 
 +E2pAccessMode=0 
 +cfg_mode=9 
 +cfg_mode=9 
 +wmode_band_equal(): Band Equal! 
 +AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD 
 +APSDCapable[0]=0 
 +APSDCapable[1]=0 
 +APSDCapable[2]=0 
 +APSDCapable[3]=0 
 +APSDCapable[4]=0 
 +APSDCapable[5]=0 
 +APSDCapable[6]=0 
 +APSDCapable[7]=0 
 +APSDCapable[8]=0 
 +APSDCapable[9]=0 
 +APSDCapable[10]=0 
 +APSDCapable[11]=0 
 +APSDCapable[12]=0 
 +APSDCapable[13]=0 
 +APSDCapable[14]=0 
 +APSDCapable[15]=0 
 +default ApCliAPSDCapable[0]=0 
 +Key1Str is Invalid key length(0) or Type(0) 
 +Key2Str is Invalid key length(0) or Type(0) 
 +Key3Str is Invalid key length(0) or Type(0) 
 +Key4Str is Invalid key length(0) or Type(0) 
 +load fw image from fw_header_image 
 +AndesMTLoadFwMethod1(2182)::pChipCap->fw_len(63888) 
 +FW Version:20151201 
 +FW Build Date:20151201183641 
 +CmdAddressLenReq:(ret = 0) 
 +CmdFwStartReq: override = 1, address = 1048576 
 +CmdStartDLRsp: WiFI FW Download Success 
 +MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC) 
 +efuse_probe: efuse = 10000012 
 +RtmpChipOpsEepromHook::e2p_type=2, inf_Type=4 
 +RtmpEepromGetDefault::e2p_dafault=2 
 +RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2 
 +NVM is FLASH mode 
 +1. Phy Mode = 14 
 +Country Region from e2p = ffff 
 +tssi_1_target_pwr_g_band = 26 
 +2. Phy Mode = 14 
 +3. Phy Mode = 14 
 +NICInitPwrPinCfg(11): Not support for HIF_MT yet! 
 +NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet! 
 +mt_mac_init()--> 
 +MtAsicInitMac()--> 
 +mt7628_init_mac_cr()--> 
 +MtAsicSetMacMaxLen(1276): Set the Max RxPktLen=1024! 
 +<--mt_mac_init() 
 + WTBL Segment 1 info: 
 + MemBaseAddr/FID:0x28000/
 + EntrySize/Cnt:32/128 
 + WTBL Segment 2 info: 
 + MemBaseAddr/FID:0x40000/
 + EntrySize/Cnt:64/128 
 + WTBL Segment 3 info: 
 + MemBaseAddr/FID:0x42000/64 
 + EntrySize/Cnt:64/128 
 + WTBL Segment 4 info: 
 + MemBaseAddr/FID:0x44000/128 
 + EntrySize/Cnt:32/128 
 +AntCfgInit(2940): Not support for HIF_MT yet! 
 +MCS Set = ff ff 00 00 01 
 +MtAsicSetChBusyStat(861): Not support for HIF_MT yet! 
 +CmdSlotTimeSet:(ret = 0) 
 +[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0 
 +[PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 
 +MtAsicSetRalinkBurstMode(3047): Not support for HIF_MT yet! 
 +MtAsicSetPiggyBack(796): Not support for HIF_MT yet! 
 +reload DPD from flash , 0x9F = [c600] doReload bit7[0] 
 +CmdLoadDPDDataFromFlash: Channel = 1, DoReload = 0 
 +MtAsicSetTxPreamble(3026): Not support for HIF_MT yet! 
 +MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet! 
 +MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0 
 +ap_ftkd> Initialize FT KDP Module... 
 +Main bssid = 00:9a:d5:51:52:46 
 +<==== rt28xx_init, Status=0 
 +@@@ ed_monitor_exit : ===> 
 +@@@ ed_monitor_exit : <=== 
 +mt7628_set_ed_cca: TURN OFF EDCCA  mac 0x10618 = 0xd7083f0f, EDCCA_Status=0 
 +WiFi Startup Cost (ra0): 3.236s 
 +Raeth v3.1 (Tasklet) 
 + 
 +phy_tx_ring = 0x023b2000, tx_ring = 0xa23b2000 
 + 
 +phy_rx_ring0 = 0x023b3000, rx_ring0 = 0xa23b3000 
 +GMAC1_MAC_ADRH -- : 0x0000009a 
 +GMAC1_MAC_ADRL -- : 0xd5515246 
 +RT305x_ESW: Link Status Changed 
 +device eth2 entered promiscuous mode 
 +RT305x_ESW: Link Status Changed 
 + 
 +# ;s =   device ra0 entered promiscuous mode 
 +device eth2.1 entered promiscuous mode 
 + br0: port 2(eth2.1) entering learning state 
 +br0: port 2(eth2.1) entering learning state 
 +br0: port 1(ra0) entering learning state 
 +br0: port 1(ra0) entering learning state 
 +ls -l br0: port 2(eth2.1) entering forwarding state 
 +br0: port 1(ra0) entering forwarding state 
 +/r proc 
 +dr-xr-xr-x    6 0        0               0 1118 
 +dr-xr-xr-x    6 0        0               0 1079 
 +dr-xr-xr-x    6 0        0               0 1012 
 +dr-xr-xr-x    6 0        0               0 982 
 +dr-xr-xr-x    6 0        0               0 676 
 +dr-xr-xr-x    6 0        0               0 675 
 +dr-xr-xr-x    6 0        0               0 616 
 +dr-xr-xr-x    6 0        0               0 416 
 +dr-xr-xr-x    6 0        0               0 415 
 +dr-xr-xr-x    6 0        0               0 414 
 +dr-xr-xr-x    6 0        0               0 145 
 +dr-xr-xr-x    6 0        0               0 144 
 +dr-xr-xr-x    6 0        0               0 139 
 +dr-xr-xr-x    6 0        0               0 138 
 +dr-xr-xr-x    6 0        0               0 136 
 +dr-xr-xr-x    6 0        0               0 131 
 +dr-xr-xr-x    6 0        0               0 129 
 +dr-xr-xr-x    6 0        0               0 128 
 +dr-xr-xr-x    6 0        0               0 126 
 +dr-xr-xr-x    6 0        0               0 98 
 +dr-xr-xr-x    6 0        0               0 31 
 +dr-xr-xr-x    6 0        0               0 30 
 +dr-xr-xr-x    6 0        0               0 29 
 +dr-xr-xr-x    6 0        0               0 28 
 +dr-xr-xr-x    6 0        0               0 27 
 +dr-xr-xr-x    6 0        0               0 26 
 +dr-xr-xr-x    6 0        0               0 25 
 +dr-xr-xr-x    6 0        0               0 24 
 +dr-xr-xr-x    6 0        0               0 13 
 +dr-xr-xr-x    6 0        0               0 12 
 +dr-xr-xr-x    6 0        0               0 11 
 +dr-xr-xr-x    6 0        0               0 10 
 +dr-xr-xr-x    6 0        0               0 9 
 +dr-xr-xr-x    6 0        0               0 8 
 +dr-xr-xr-x    6 0        0               0 7 
 +dr-xr-xr-x    6 0        0               0 6 
 +dr-xr-xr-x    6 0        0               0 5 
 +dr-xr-xr-x    6 0        0               0 4 
 +dr-xr-xr-x    6 0        0               0 3 
 +dr-xr-xr-x    6 0        0               0 2 
 +dr-xr-xr-x    6 0        0               0 1 
 +lrwxrwxrwx    1 0        0              64 self -> 1118 
 +lrwxrwxrwx    1 0        0              11 mounts -> self/mounts 
 +lrwxrwxrwx    1 0        0               8 net -> self/net 
 +dr-xr-xr-x    2 0        0               0 sysvipc 
 +dr-xr-xr-x    3 0        0               0 fs 
 +dr-xr-xr-x    2 0        0               0 driver 
 +dr-xr-xr-x    4 0        0               0 tty 
 +dr-xr-xr-x    4 0        0               0 bus 
 +dr-xr-xr-x    1 0        0               0 sys 
 +dr-xr-xr-x   67 0        0               0 irq 
 +-r--r--r--    1 0        0               0 misc 
 +dr-xr-xr-x    3 0        0               0 scsi 
 +-r--r--r--    1 0        0               0 mtd 
 +-r--r--r--    1 0        0               0 execdomains 
 +-r--r--r--    1 0        0               0 ioports 
 +-r--r--r--    1 0        0               0 iomem 
 +-r--r--r--    1 0        0               0 timer_list 
 +-r--r--r--    1 0        0               0 modules 
 +-r--r--r--    1 0        0               0 buddyinfo 
 +-r--r--r--    1 0        0               0 pagetypeinfo 
 +-r--r--r--    1 0        0               0 vmstat 
 +-r--r--r--    1 0        0               0 zoneinfo 
 +-r--------    1 0        0               0 vmallocinfo 
 +-rw-r--r--    1 0        0               0 slabinfo 
 +-r--r--r--    1 0        0               0 filesystems 
 +-r--r--r--    1 0        0               0 locks 
 +-r--r--r--    1 0        0               0 cmdline 
 +-r--r--r--    1 0        0               0 cpuinfo 
 +-r--r--r--    1 0        0               0 devices 
 +-r--r--r--    1 0        0               0 interrupts 
 +-r--r--r--    1 0        0               0 loadavg 
 +-r--r--r--    1 0        0               0 meminfo 
 +-r--r--r--    1 0        0               0 stat 
 +-r--r--r--    1 0        0               0 uptime 
 +-r--r--r--    1 0        0               0 version 
 +-r--r--r--    1 0        0               0 softirqs 
 +-r--------    1 0        0       2147278848 kcore 
 +-r--------    1 0        0               0 kmsg 
 +-r--r--r--    1 0        0               0 crypto 
 +-r--r--r--    1 0        0               0 diskstats 
 +-r--r--r--    1 0        0               0 partitions 
 +dr-xr-xr-x    2 0        0               0 mt7628 
 +# cat Jan  1 00:00:23 miniupnpd[3075]: WPS listening on port 7777 
 +/proehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 130(0x00000082) 
 +FM detection done! loop = 1 
 +SR calibration value u1SrCalVal = 6 
 +rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller 
 +rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 
 +crt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 
 +rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00 
 +usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 
 +usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 
 +usb usb1: Product: Ralink EHCI Host Controller 
 +usb usb1: Manufacturer: Linux 2.6.36 ehci_hcd 
 +usb usb1: SerialNumber: rt3xxx 
 +hub 1-0:1.0: USB hub found 
 +hub 1-0:1.0: 1 port detected 
 +ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver 
 +rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller 
 +rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 
 +rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 
 +usb usb2: New USB device found, idVendor=1d6b, idProduct=0001 
 +usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 
 +usb usb2: Product: RT3xxx OHCI Controller 
 +usb usb2: Manufacturer: Linux 2.6.36 ohci_hcd 
 +usb usb2: SerialNumber: rt3xxx-ohci 
 +hub 2-0:1.0: USB hub found 
 +hub 2-0:1.0: 1 port detected 
 +usb 1-1: new high speed USB device using rt3xxx-ehci and address 2 
 +usb 1-1: New USB device found, idVendor=1a40, idProduct=0101 
 +usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0 
 +usb 1-1: Product: USB 2.0 Hub 
 +hub 1-1:1.0: USB hub found 
 +hub 1-1:1.0: 4 ports detected 
 +/usb 1-1.3: new high speed USB device using rt3xxx-ehci and address 3 
 +usb 1-1.3: New USB device found, idVendor=058f, idProduct=6364 
 +usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3 
 +usb 1-1.3: Product: Mass Storage Device 
 +usb 1-1.3: Manufacturer: Generic 
 +usb 1-1.3: SerialNumber: 058F63646476 
 +cpu# cat /proc/cpuinfo  
 +system type : MT7628 
 +processor :
 +cpu model : MIPS 24Kc V5.5 
 +BogoMIPS : 386.04 
 +wait instruction : yes 
 +microsecond timers : yes 
 +tlb_entries : 32 
 +extra interrupt vector : yes 
 +hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb] 
 +ASEs implemented : mips16 dsp 
 +shadow register sets : 1 
 +core : 0 
 +VCED exceptions : not available 
 +VCEI exceptions : not available 
 + 
 +# # cat /proc/cpuinfo     usbcore: registered new interface driver usbserial 
 +USB Serial support registered for generic 
 +usbcore: registered new interface driver usbserial_generic 
 +usbserial: USB Serial Driver core 
 + usbcore: registered new interface driver cdc_acm 
 +cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters 
 +USB Serial support registered for GSM modem (1-port) 
 +usbcore: registered new interface driver option 
 +option: v0.7.2:USB Driver for GSM modems 
 + USB Serial support registered for cp210x 
 +usbcore: registered new interface driver cp210x 
 +cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver 
 + usbcore: registered new interface driver cdc_ether 
 +usbcore: registered new interface driver cdc_subset 
 +Initializing USB Mass Storage driver... 
 +scsi0 : usb-storage 1-1.3:1.0 
 +usbcore: registered new interface driver usb-storage 
 +USB Mass Storage support registered. 
 + mscsi 0:0:0:0: Direct-Access     Generic- SD/MMC           1.00 PQ: 0 ANSI: 0 
 +scsi 0:0:0:1: Direct-Access     Generic- Compact Flash    1.01 PQ: 0 ANSI: 0 
 +scsi 0:0:0:2: Direct-Access     Generic- SM/xD-Picture    1.02 PQ: 0 ANSI: 0 
 +scsi 0:0:0:3: Direct-Access     Generic- MS/MS-Pro        1.03 PQ: 0 ANSI: 0 CCS 
 +sd 0:0:0:0: Attached scsi generic sg0 type 0 
 +sd 0:0:0:0: [sda] Attached SCSI removable disk 
 +sd 0:0:0:1: Attached scsi generic sg1 type 0 
 +sd 0:0:0:1: [sdb] Attached SCSI removable disk 
 +sd 0:0:0:2: Attached scsi generic sg2 type 0 
 +sd 0:0:0:2: [sdc] Attached SCSI removable disk 
 +sd 0:0:0:3: Attached scsi generic sg3 type 0 
 +# cat /proc/msd 0:0:0:3: [sdd] Attached SCSI removable disk 
 +            
 +# cat /proce/  /mem# cat /proc/meminfo  
 +MemTotal:          58840 kB 
 +MemFree:           25480 kB 
 +Buffers:               0 kB 
 +Cached:            22156 kB 
 +SwapCached:            0 kB 
 +Active:             4904 kB 
 +Inactive:          18284 kB 
 +Active(anon):       1032 kB 
 +Inactive(anon):        8 kB 
 +Active(file):       3872 kB 
 +Inactive(file):    18276 kB 
 +Unevictable:           0 kB 
 +Mlocked:               0 kB 
 +SwapTotal:             0 kB 
 +SwapFree:              0 kB 
 +Dirty:                 0 kB 
 +Writeback:             0 kB 
 +AnonPages:          1044 kB 
 +Mapped:             1148 kB 
 +Shmem:                 8 kB 
 +Slab:               7620 kB 
 +SReclaimable:       2712 kB 
 +SUnreclaim:         4908 kB 
 +KernelStack:         352 kB 
 +PageTables:          188 kB 
 +NFS_Unstable:          0 kB 
 +Bounce:                0 kB 
 +WritebackTmp:          0 kB 
 +CommitLimit:       29420 kB 
 +Committed_AS:       3952 kB 
 +VmallocTotal:    1048372 kB 
 +VmallocUsed:        2040 kB 
 +VmallocChunk:    1042380 kB 
 +# car   t /r proc/par# cat /proc/partitions  
 +major minor  #blocks  name 
 + 
 +  31        0       8192 mtdblock0 
 +  31        1        192 mtdblock1 
 +  31        2         64 mtdblock2 
 +  31        3         64 mtdblock3 
 +  31        4       7872 mtdblock4 
 +# cat /proc/dev# cat /proc/devices  
 +Character devices: 
 +  1 mem 
 +  2 pty 
 +  3 ttyp 
 +  4 ttyS 
 +  5 /dev/tty 
 +  5 /dev/console 
 +  5 /dev/ptmx 
 + 10 misc 
 + 21 sg 
 + 86 ch 
 + 90 mtd 
 +108 ppp 
 +128 ptm 
 +136 pts 
 +166 ttyACM 
 +180 usb 
 +188 ttyUSB 
 +189 usb_device 
 +206 osst 
 +251 nvram 
 +252 gpio 
 +253 rdm0 
 +254 bsg 
 + 
 +Block devices: 
 +  1 ramdisk 
 +259 blkext 
 +  8 sd 
 + 11 sr 
 + 31 mtdblock 
 + 65 sd 
 + 66 sd 
 + 67 sd 
 + 68 sd 
 + 69 sd 
 + 70 sd 
 + 71 sd 
 +128 sd 
 +129 sd 
 +130 sd 
 +131 sd 
 +132 sd 
 +133 sd 
 +134 sd 
 +135 sd 
 +# cat/  /proc/iopoty  rts 
 +# cat /proc/cpu# cat /proc/cpuinfo  
 +system type : MT7628 
 +processor :
 +cpu model : MIPS 24Kc V5.5 
 +BogoMIPS : 386.04 
 +wait instruction : yes 
 +microsecond timers : yes 
 +tlb_entries : 32 
 +extra interrupt vector : yes 
 +hardware watchpoint : yes, count: 4, address/irw mask: [0x0ffc, 0x0ffc, 0x0ffb, 0x0ffb] 
 +ASEs implemented : mips16 dsp 
 +shadow register sets : 1 
 +core : 0 
 +VCED exceptions : not available 
 +VCEI exceptions : not available 
 + 
 +# cat /proc/cmd# cat /proc/cmdline  
 +console=ttyS1,57600n8 root=/dev/ram0 console=ttyS0 
 +# m dmesh 
 +/bin/sh: dmesh: not found 
 +# dmesg 
 +eneric- MS/MS-Pro        1.03 PQ: 0 ANSI: 0 CCS 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Bad LUN (0:4) 
 +usb-storage: scsi cmd done, result=0x40000 
 +usb-storage: *** thread sleeping. 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Bad target number (1:0) 
 +usb-storage: scsi cmd done, result=0x40000 
 +usb-storage: *** thread sleeping. 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Bad target number (2:0) 
 +usb-storage: scsi cmd done, result=0x40000 
 +usb-storage: *** thread sleeping. 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Bad target number (3:0) 
 +usb-storage: scsi cmd done, result=0x40000 
 +usb-storage: *** thread sleeping. 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Bad target number (4:0) 
 +usb-storage: scsi cmd done, result=0x40000 
 +usb-storage: *** thread sleeping. 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Bad target number (5:0) 
 +usb-storage: scsi cmd done, result=0x40000 
 +usb-storage: *** thread sleeping. 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Bad target number (6:0) 
 +usb-storage: scsi cmd done, result=0x40000 
 +usb-storage: *** thread sleeping. 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Bad target number (7:0) 
 +usb-storage: scsi cmd done, result=0x40000 
 +usb-storage: *** thread sleeping. 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Command TEST_UNIT_READY (6 bytes) 
 +usb-storage:  00 00 00 00 00 00 
 +usb-storage: Bulk Command S 0x43425355 T 0x5 L 0 F 0 Trg 0 LUN 0 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0x5 R 0 Stat 0x1 
 +usb-storage: -- transport indicates command failure 
 +usb-storage: Issuing auto-REQUEST_SENSE 
 +usb-storage: Bulk Command S 0x43425355 T 0x6 L 18 F 128 Trg 0 LUN 0 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries 
 +usb-storage: Status code 0; transferred 18/18 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk data transfer result 0x0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0x6 R 0 Stat 0x0 
 +usb-storage: -- Result from auto-sense is 0 
 +usb-storage: -- code: 0xf0, key: 0x2, ASC: 0x3a, ASCQ: 0x0 
 +usb-storage: Not Ready: Medium not present 
 +usb-storage: scsi cmd done, result=0x2 
 +usb-storage: *** thread sleeping. 
 +sd 0:0:0:0: Attached scsi generic sg0 type 0 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Command TEST_UNIT_READY (6 bytes) 
 +usb-storage:  00 00 00 00 00 00 
 +usb-storage: Bulk Command S 0x43425355 T 0x7 L 0 F 0 Trg 0 LUN 0 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0x7 R 0 Stat 0x1 
 +usb-storage: -- transport indicates command failure 
 +usb-storage: Issuing auto-REQUEST_SENSE 
 +usb-storage: Bulk Command S 0x43425355 T 0x8 L 18 F 128 Trg 0 LUN 0 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries 
 +usb-storage: Status code 0; transferred 18/18 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk data transfer result 0x0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0x8 R 0 Stat 0x0 
 +usb-storage: -- Result from auto-sense is 0 
 +usb-storage: -- code: 0xf0, key: 0x2, ASC: 0x3a, ASCQ: 0x0 
 +usb-storage: Not Ready: Medium not present 
 +usb-storage: scsi cmd done, result=0x2 
 +usb-storage: *** thread sleeping. 
 +sd 0:0:0:0: [sda] Attached SCSI removable disk 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Command TEST_UNIT_READY (6 bytes) 
 +usb-storage:  00 00 00 00 00 00 
 +usb-storage: Bulk Command S 0x43425355 T 0x9 L 0 F 0 Trg 0 LUN 1 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0x9 R 0 Stat 0x1 
 +usb-storage: -- transport indicates command failure 
 +usb-storage: Issuing auto-REQUEST_SENSE 
 +usb-storage: Bulk Command S 0x43425355 T 0xa L 18 F 128 Trg 0 LUN 1 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries 
 +usb-storage: Status code 0; transferred 18/18 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk data transfer result 0x0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0xa R 0 Stat 0x0 
 +usb-storage: -- Result from auto-sense is 0 
 +usb-storage: -- code: 0xf0, key: 0x2, ASC: 0x3a, ASCQ: 0x0 
 +usb-storage: Not Ready: Medium not present 
 +usb-storage: scsi cmd done, result=0x2 
 +usb-storage: *** thread sleeping. 
 +sd 0:0:0:1: Attached scsi generic sg1 type 0 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Command TEST_UNIT_READY (6 bytes) 
 +usb-storage:  00 00 00 00 00 00 
 +usb-storage: Bulk Command S 0x43425355 T 0xb L 0 F 0 Trg 0 LUN 1 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0xb R 0 Stat 0x1 
 +usb-storage: -- transport indicates command failure 
 +usb-storage: Issuing auto-REQUEST_SENSE 
 +usb-storage: Bulk Command S 0x43425355 T 0xc L 18 F 128 Trg 0 LUN 1 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries 
 +usb-storage: Status code 0; transferred 18/18 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk data transfer result 0x0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0xc R 0 Stat 0x0 
 +usb-storage: -- Result from auto-sense is 0 
 +usb-storage: -- code: 0xf0, key: 0x2, ASC: 0x3a, ASCQ: 0x0 
 +usb-storage: Not Ready: Medium not present 
 +usb-storage: scsi cmd done, result=0x2 
 +usb-storage: *** thread sleeping. 
 +sd 0:0:0:1: [sdb] Attached SCSI removable disk 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Command TEST_UNIT_READY (6 bytes) 
 +usb-storage:  00 00 00 00 00 00 
 +usb-storage: Bulk Command S 0x43425355 T 0xd L 0 F 0 Trg 0 LUN 2 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0xd R 0 Stat 0x1 
 +usb-storage: -- transport indicates command failure 
 +usb-storage: Issuing auto-REQUEST_SENSE 
 +usb-storage: Bulk Command S 0x43425355 T 0xe L 18 F 128 Trg 0 LUN 2 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries 
 +usb-storage: Status code 0; transferred 18/18 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk data transfer result 0x0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0xe R 0 Stat 0x0 
 +usb-storage: -- Result from auto-sense is 0 
 +usb-storage: -- code: 0xf0, key: 0x2, ASC: 0x3a, ASCQ: 0x0 
 +usb-storage: Not Ready: Medium not present 
 +usb-storage: scsi cmd done, result=0x2 
 +usb-storage: *** thread sleeping. 
 +sd 0:0:0:2: Attached scsi generic sg2 type 0 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Command TEST_UNIT_READY (6 bytes) 
 +usb-storage:  00 00 00 00 00 00 
 +usb-storage: Bulk Command S 0x43425355 T 0xf L 0 F 0 Trg 0 LUN 2 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0xf R 0 Stat 0x1 
 +usb-storage: -- transport indicates command failure 
 +usb-storage: Issuing auto-REQUEST_SENSE 
 +usb-storage: Bulk Command S 0x43425355 T 0x10 L 18 F 128 Trg 0 LUN 2 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries 
 +usb-storage: Status code 0; transferred 18/18 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk data transfer result 0x0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0x10 R 0 Stat 0x0 
 +usb-storage: -- Result from auto-sense is 0 
 +usb-storage: -- code: 0xf0, key: 0x2, ASC: 0x3a, ASCQ: 0x0 
 +usb-storage: Not Ready: Medium not present 
 +usb-storage: scsi cmd done, result=0x2 
 +usb-storage: *** thread sleeping. 
 +sd 0:0:0:2: [sdc] Attached SCSI removable disk 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Command TEST_UNIT_READY (6 bytes) 
 +usb-storage:  00 00 00 00 00 00 
 +usb-storage: Bulk Command S 0x43425355 T 0x11 L 0 F 0 Trg 0 LUN 3 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0x11 R 0 Stat 0x1 
 +usb-storage: -- transport indicates command failure 
 +usb-storage: Issuing auto-REQUEST_SENSE 
 +usb-storage: Bulk Command S 0x43425355 T 0x12 L 18 F 128 Trg 0 LUN 3 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries 
 +usb-storage: Status code 0; transferred 18/18 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk data transfer result 0x0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0x12 R 0 Stat 0x0 
 +usb-storage: -- Result from auto-sense is 0 
 +usb-storage: -- code: 0xf0, key: 0x2, ASC: 0x3a, ASCQ: 0x0 
 +usb-storage: Not Ready: Medium not present 
 +usb-storage: scsi cmd done, result=0x2 
 +usb-storage: *** thread sleeping. 
 +sd 0:0:0:3: Attached scsi generic sg3 type 0 
 +usb-storage: queuecommand called 
 +usb-storage: *** thread awakened. 
 +usb-storage: Command TEST_UNIT_READY (6 bytes) 
 +usb-storage:  00 00 00 00 00 00 
 +usb-storage: Bulk Command S 0x43425355 T 0x13 L 0 F 0 Trg 0 LUN 3 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0x13 R 0 Stat 0x1 
 +usb-storage: -- transport indicates command failure 
 +usb-storage: Issuing auto-REQUEST_SENSE 
 +usb-storage: Bulk Command S 0x43425355 T 0x14 L 18 F 128 Trg 0 LUN 3 CL 6 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 31 bytes 
 +usb-storage: Status code 0; transferred 31/31 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk command transfer result=0 
 +usb-storage: usb_stor_bulk_transfer_sglist: xfer 18 bytes, 1 entries 
 +usb-storage: Status code 0; transferred 18/18 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk data transfer result 0x0 
 +usb-storage: Attempting to get CSW... 
 +usb-storage: usb_stor_bulk_transfer_buf: xfer 13 bytes 
 +usb-storage: Status code 0; transferred 13/13 
 +usb-storage: -- transfer complete 
 +usb-storage: Bulk status result = 0 
 +usb-storage: Bulk Status S 0x53425355 T 0x14 R 0 Stat 0x0 
 +usb-storage: -- Result from auto-sense is 0 
 +usb-storage: -- code: 0xf0, key: 0x2, ASC: 0x3a, ASCQ: 0x0 
 +usb-storage: Not Ready: Medium not present 
 +usb-storage: scsi cmd done, result=0x2 
 +usb-storage: *** thread sleeping. 
 +sd 0:0:0:3: [sdd] Attached SCSI removable disk 
 +br0: no IPv6 routers present 
 +#  
 +</nowiki>
 </WRAP>\\ </WRAP>\\
  
  • Last modified: 2023/09/21 08:41
  • by cyrevolt