Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
inbox:toh:wavlink:wavlink_ac1200 [2022/01/13 18:44] – Added GPL sources & clone devices. varuinbox:toh:wavlink:wavlink_ac1200 [2024/04/23 01:01] – [Table] ianchi
Line 15: Line 15:
 ===== OpenWrt support ===== ===== OpenWrt support =====
  
-<color red>**Partially supported (no WAN yet).**</color>+Preliminary support[[https://github.com/openwrt/openwrt/pull/15179|PR]] in process.
  
  
  
 ===== Supporting activities ===== ===== Supporting activities =====
-https://forum.openwrt.org/t/wl-wn572hg3-soft-hack+[[https://forum.openwrt.org/t/wl-wn572hg3-soft-hack|Forum thread]]
  
-https://www.pastiebin.com/5f1299e2c3a0b+[[https://github.com/openwrt/openwrt/pull/15179|Pull Request]]
  
-https://deviwiki.com/wiki/MediaTek_MT7620#Devices_using_MT7620A_.2F_MT7620N 
  
-===== Experimental firmware =====+===== Installation =====
  
-A partial working version can be taken from+Preliminary image can be obtained from [[https://github.com/ianchi/openwrt/releases/tag/wavlink1200-v0.1|here]]
-[[:toh:asus:rp-n53]]+
  
-  - download https://downloads.openwrt.org/releases/19.07.4/targets/ramips/mt7620/openwrt-19.07.4-ramips-mt7620-rp-n53-squashfs-sysupgrade.bin +  * Set host computer's ip to 192.168.10.100 
-  - rename to firmware.bin +  * Save sysupgrade image file as 'firmware.bin' 
-  - set host IP to 192.168.10.100 +  * Setup tftp server on computer, serving the file from root 
-  - start tftp server +  * Connect your computer to the LAN port of the WAVLINK router via an Ethernet cable 
-  - connect power to the router +  * Press and hold the reset button while powering on the router 
-  - over UART wait for uBoot menu +  * Keep it pressed for ten seconds 
-  - select option "2: Load system code then write to Flash via TFTP." +  * Wait for firmware to be uploaded
-  - done+
  
-Firmware from the Netgear [[:toh:netgear:ex3700_ex3800]] or EX6120 has also been tested working, and adds 5GHz WiFi support. This is flashed in the same way as the above. Please allow a few minutes on first boot for SSH key generation & flash initialization. If first boot fails, reflash the firmware bin and the subsequent boot should succeed. 
  
 ===== GPL Sources ===== ===== GPL Sources =====
Line 48: Line 44:
  
 ===== Hardware highlights ===== ===== Hardware highlights =====
-^ CPU                   ^ Ram      ^ Flash ^ Wi-Fi chip   ^ Network                                            ^ 2.4 GHz ^ 5 GHz          ^ USB    ^ Serial   ^ JTag ^ LEDs ^ Buttons ^ +^ CPU                ^ Ram      ^ Flash   ^ Wi-Fi chip      ^ Network                                         ^ 2.4 GHz        ^ 5 GHz          ^ USB                      ^ Serial            ^ JTag  ^ LEDs  ^ Buttons    
-| MT7620A @ 580 MHz   |  64 MiB  |  8 MiB  | MT7612E (2T2R) |  2x 10/100 (WANDC24V/0.5A, Passive PoE) | Yes, b/g/n/ac | Yes, b/g/n/ac   |  [[#USB|Yes (USB 2.0)]]   [[#Serial|Yes]]      ?    | 7 | 1 (reset) | +| MT7620A @ 580 MHz  |  64 MiB  |  8 MiB  | MT7612E (2T2R)  |  10/100 LAN + 1Gb WAN (DC24V/0.5A, Passive PoE) | Yes, b/g/n/ac  | Yes, b/g/n/ac  |  [[#USB|Yes (USB 2.0)]]  [[#Serial|Yes]]   ?    | 7     | 1 (reset)  |
  
 /*** if info available: uncomment and fill in /*** if info available: uncomment and fill in
Line 105: Line 101:
 The power LED does not seem to be on a GPIO (all GPIOs were software toggled within stock firmware for the discovery process). The stock firmware does not seem to utilize it for status messages either. The power LED does not seem to be on a GPIO (all GPIOs were software toggled within stock firmware for the discovery process). The stock firmware does not seem to utilize it for status messages either.
  
-^ GPIO ^ FUNCTION             ^ STATE       +^ GPIO ^ FUNCTION             ^ STATE      
-| 1 | Reset Button        | Active Low  +| 1 | Reset Button        | Active Low | 
-| 12 | Wifi Signal Mid LED  | Active High +| 12 | Wifi Signal Mid LED  | Active Low 
-| 13 | Wifi Signal High LED | Active High +| 13 | Wifi Signal High LED | Active Low 
-| 41 | LAN LED        | Active High +| 41 | LAN LED        | Active Low 
-| 43 | Wifi Signal Low LED  | Active High +| 43 | Wifi Signal Low LED  | Active Low 
-| 44 | WAN LED        | Active High +| 44 | WAN LED        | Active Low 
-| 72 | Wifi LED        | Active High |+| 72 | Wifi LED        | Active Low |
  
 ==== Connectors ==== ==== Connectors ====
Line 186: Line 182:
 ===== Hardware ===== ===== Hardware =====
 ==== Info ==== ==== Info ====
-^ Architecture     | MIPS 24KEc                             +^ Architecture    | MIPS 24KEc                                    
-^ Vendor           | Mediatek                           +^ Vendor          | Mediatek                                      
-^ Bootloader       | U-Boot 1.1.3 (Jan 20 2018 - 15:44:18)| +^ Bootloader      | U-Boot 1.1.3 (Jan 20 2018 - 15:44:18)         
-^ System-On-Chip   | MT7620A ver:2 eco:6 - MIPS 24K V4.12   +^ System-On-Chip  | MT7620A ver:2 eco:6 - MIPS 24K V4.12          
-^ CPU/Speed        | MT7620A @ 580 MHz                +^ CPU/Speed       | MT7620A @ 580 MHz                             
-^ Flash-Chip       | GD25Q64B                         +^ Flash-Chip      | GD25Q64B                                      
-^ Flash size       | 8 MiB                            +^ Flash size      | 8 MiB                                         
-^ RAM              | 64 MiB                           +^ RAM             | 64 MiB                                        
-^ Wireless         | MT7620A 2.4GHz 802.11bgn, MT7610E 5 GHz a/ac| +^ Wireless        | MT7620A 2.4GHz 802.11bgn, MT7610E 5 GHz a/ac  
-^ Ethernet         | 10/100 Mbit/s w/ vlan support    +^ Ethernet        1x 10/100Mb LAN + 1x 1Gb-WAN (vlan support)   
-^ Switch           | MT7530WU         +^ Switch          | MT7530WU                                      
-^ USB              | 1x 2.0                           +^ USB             | 1x 2.0                                        
-^ Serial           | [[#Serial|Yes]]                  +^ Serial          | [[#Serial|Yes]]                               
-^ JTAG             | [[#JTAG|not yet identified]]          |+^ JTAG            | [[#JTAG|not yet identified]]                  |
  
 ==== Components ==== ==== Components ====
Line 298: Line 294:
 http://ip/webcmd.shtml http://ip/webcmd.shtml
  
-Please note that this (as well as serial console login) has been removed in newer firmware versions (WN572HG3-A_2021.07.21.bin). You will need WN572HG3-WAVLINK_WO_20200717.bin or earlier.+Please note that this (as well as serial console login) has been removed in newer firmware versions (WN572HG3-A_2021.07.21.bin). You will need [[http://files.wavlink.com/fw/OUTDOOR%20AP/WN572HG3-WAVLINK_WO_20200717.bin]] or earlier.
  
 ==== Telnet ==== ==== Telnet ====
  • Last modified: 2024/05/01 20:02
  • by ianchi