Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| inbox:toh:wavlink:wavlink_ac1200 [2021/05/25 18:31] – ↷ Links adapted because of a move operation tmomas | inbox:toh:wavlink:wavlink_ac1200 [2024/04/23 01:01] – [Table] ianchi | ||
|---|---|---|---|
| Line 9: | Line 9: | ||
| {{ media: | {{ media: | ||
| + | Also known as:\\ | ||
| + | - [[https:// | ||
| + | - Wavlink AERIAL HD4 | ||
| ===== OpenWrt support ===== | ===== OpenWrt support ===== | ||
| - | <color red> | + | Preliminary support. [[https:// |
| ===== Supporting activities ===== | ===== Supporting activities ===== | ||
| - | https:// | + | [[https:// |
| - | https://www.pastiebin.com/5f1299e2c3a0b | + | [[https://github.com/openwrt/ |
| - | https:// | ||
| - | ===== Experimental firmware | + | ===== Installation |
| + | |||
| + | Preliminary image can be obtained from [[https:// | ||
| + | |||
| + | * Set host computer' | ||
| + | * Save sysupgrade image file as ' | ||
| + | * Setup tftp server on computer, serving the file from root | ||
| + | * Connect your computer to the LAN port of the WAVLINK router via an Ethernet cable | ||
| + | * Press and hold the reset button while powering on the router | ||
| + | * Keep it pressed for ten seconds | ||
| + | * Wait for firmware to be uploaded | ||
| - | A partial working version can be taken from: | + | ===== GPL Sources ===== |
| - | [[: | + | |
| - | - download https://downloads.openwrt.org/releases/19.07.4/ | + | Available via FTP here: [[ftp://ftp.pearl.de/treiber/NX4812_open_source.tar.gz|GPL Sources]]\\ |
| - | - rename | + | Please note, this FTP will not produce directory listings if browsed manually, the file will need to be downloaded directly. The filesize is 1, |
| - | - set host IP to 192.168.10.100 | + | |
| - | - start tftp server | + | |
| - | - connect power to the router | + | |
| - | - over UART wait for uBoot menu | + | |
| - | - select option "2: Load system code then write to Flash via TFTP." | + | |
| - | - done | + | |
| ===== Hardware highlights ===== | ===== Hardware highlights ===== | ||
| - | ^ CPU | + | ^ CPU ^ Ram ^ Flash |
| - | | MT7620A @ 580 MHz | + | | MT7620A @ 580 MHz | 64 MiB | 8 MiB | MT7612E (2T2R) |
| /*** if info available: uncomment and fill in | /*** if info available: uncomment and fill in | ||
| Line 90: | Line 96: | ||
| ^ BUTTON | ^ BUTTON | ||
| | Reset | | Reset | ||
| + | |||
| + | ==== GPIO ==== | ||
| + | |||
| + | The power LED does not seem to be on a GPIO (all GPIOs were software toggled within stock firmware for the discovery process). The stock firmware does not seem to utilize it for status messages either. | ||
| + | |||
| + | ^ GPIO ^ FUNCTION | ||
| + | | 1 | Reset Button | Active Low | | ||
| + | | 12 | Wifi Signal Mid LED | Active Low | | ||
| + | | 13 | Wifi Signal High LED | Active Low | | ||
| + | | 41 | LAN LED | Active Low | | ||
| + | | 43 | Wifi Signal Low LED | Active Low | | ||
| + | | 44 | WAN LED | Active Low | | ||
| + | | 72 | Wifi LED | Active Low | | ||
| ==== Connectors ==== | ==== Connectors ==== | ||
| The following connectors can be found on the PCB: | The following connectors can be found on the PCB: | ||
| - | ^ Connector | + | ^ Connector |
| | J1 | POE | Center Tap (CT1, CT2) and Signal Path (SP1, SP2) | | | J1 | POE | Center Tap (CT1, CT2) and Signal Path (SP1, SP2) | | ||
| - | | J2 | RS232 | VCC (3.3V), TX, RX, GND | + | | J2 | RS232 | VCC (3.3V), TX, RX, GND | |
| | J3 | USB | D+ middle towards J4, D- middle towards J2 | | | J3 | USB | D+ middle towards J4, D- middle towards J2 | | ||
| | J4 | 24V | 2x 24V, 2x GND | | | J4 | 24V | 2x 24V, 2x GND | | ||
| Line 163: | Line 182: | ||
| ===== Hardware ===== | ===== Hardware ===== | ||
| ==== Info ==== | ==== Info ==== | ||
| - | ^ Architecture | + | ^ Architecture |
| - | ^ Vendor | + | ^ Vendor |
| - | ^ Bootloader | + | ^ Bootloader |
| - | ^ System-On-Chip | + | ^ System-On-Chip |
| - | ^ CPU/ | + | ^ CPU/ |
| - | ^ Flash-Chip | + | ^ Flash-Chip |
| - | ^ Flash size | + | ^ Flash size | 8 MiB |
| - | ^ RAM | 64 MiB | + | ^ RAM |
| - | ^ Wireless | + | ^ Wireless |
| - | ^ Ethernet | + | ^ Ethernet |
| - | ^ Switch | + | ^ Switch |
| - | ^ USB | 1x 2.0 | + | ^ USB |
| - | ^ Serial | + | ^ Serial |
| - | ^ JTAG | + | ^ JTAG | [[#JTAG|not yet identified]] |
| ==== Components ==== | ==== Components ==== | ||
| Line 274: | Line 293: | ||
| http:// | http:// | ||
| + | |||
| + | Please note that this (as well as serial console login) has been removed in newer firmware versions (WN572HG3-A_2021.07.21.bin). You will need [[http:// | ||
| ==== Telnet ==== | ==== Telnet ==== | ||
| Line 292: | Line 313: | ||
| ==== Antennas ==== | ==== Antennas ==== | ||
| <WRAP BOX> | <WRAP BOX> | ||
| - | Advice, while you are in there strengthen the antenna connectors with more solder and epoxy. | + | Advice: while you are in there strengthen the antenna connectors with more solder and epoxy. |
| </ | </ | ||