Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
inbox:tp-link:tp-link_mr200_v4 [2019/03/12 19:18] – Links to supporting activities added tmomasinbox:toh:tp-link:tp-link_mr200_v4 [2021/01/13 05:13] (current) – [TP-Link Archer MR200 v4] mctifa
Line 6: Line 6:
 | {{page>meta:infobox:construction&noheader&nofooter&noeditbtn}} | | {{page>meta:infobox:construction&noheader&nofooter&noeditbtn}} |
  
-//Write a short, relevant description of the device. Include a technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about right. A picture is good, too. Edit the page to see how to add pictures.// 
  
-LTE Dual band router with 4 fast (100mbps) ethernet ports. +LTE Dual band router with 4 fast (100mbps) Ethernet ports.
- +
-/*****/ +
-/* How to add images ========> http://wiki.openwrt.org/meta/adding_images_to_openwrt_wiki */ +
-/*****/ +
- +
-{{ media:example:genericrouter1.png?200|Generic Router}}+
  
 +{{ :media:tplink:mr200_v4_overview.png?nolink&400|}}
  
 ===== OpenWrt support ===== ===== OpenWrt support =====
Line 44: Line 38:
 ===== Hardware highlights ===== ===== Hardware highlights =====
 ^ CPU               ^ Ram      ^ Flash   ^ Network     ^ WLAN           ^ USB   ^ Serial   ^ JTag   ^ ^ CPU               ^ Ram      ^ Flash   ^ Network     ^ WLAN           ^ USB   ^ Serial   ^ JTag   ^
-| MT7628 @ 580MHz    64 MiB  |  8 MiB  |  4x 10/100  |  ac/n/a/b/g/ |       Yes    |      |+| MT7628 @ 580MHz    64 MiB  |  8 MiB  |  4x 10/100  |  ac/n/a/b/g/ |       Yes    |      |
  
  
Line 112: Line 106:
 ===== Hardware ===== ===== Hardware =====
 ==== Info ==== ==== Info ====
-^ Architecture     EXAMPLE MIPS                             +^ Architecture      Ramips                      
-^ Vendor           EXAMPLE Ralink                           +^ Vendor            | Ralink                      
-^ Bootloader       EXAMPLE U-Boot                           +^ Bootloader        | U-Boot                      
-^ System-On-Chip   EXAMPLE Ralink RT3052 MIPS 24K V4.12   +^ System-On-Chip    Mediatek MT7628DAN        
-^ CPU/Speed        EXAMPLE 451 MHz                          +^ CPU/Speed         580 MHz                     
-^ Flash-Chip       EXAMPLE unkown                           +^ Flash-Chip        W25Q64BV                    
-^ Flash size       EXAMPLE MiB                            +^ Flash size        | 8 MB                        
-^ RAM              EXAMPLE 64 MiB                           +^ RAM               | 64 MB                       
-^ Wireless         | EXAMPLE RT2860v2 2.4GHz 802.11bgn        +^ Wireless 2.4GHz   | 802.11b/g/  300Mbps       | 
-^ Ethernet         EXAMPLE 10/100 Mbit/s wvlan support    +^ Wireless 5  GHz   | 802.11ac/n/ 433Mbps       | 
-^ USB              EXAMPLE 1x 2.0                           +^ Modem             | QualComm 9207 LTE, 3G       
-^ Serial           | EXAMPLE [[#Serial|Yes]]                  +^ Ethernet          10/100Mbps LAN Ports      | 
-^ JTAG             EXAMPLE [[#JTAG|Not populated]]          |+^ :::               | 1 10/100Mbps LAN/WAN Port   
 +^ USB               No                          
 +^ Serial            | Yes                         
 +^ JTAG              No                          |
  
  
Line 143: Line 140:
 /* Thanks, your wiki administration - Oct. 2015 */ /* Thanks, your wiki administration - Oct. 2015 */
  
-**Insert photo of front of the casing** +**Front PCB** 
 +{{ :media:tplink:tplink_mr200_v4_front.jpg?nolink&400 |}}
 **Insert photo of back of the casing** **Insert photo of back of the casing**
  
Line 160: Line 157:
 -> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc. -> [[docs:techref:hardware:port.serial]] general information about the serial port, serial port cable, etc.
  
-How to connect to the Serial Port of this specific device:\\ +How to connect to the Serial Port of MR-200 V4
-**Insert photo of PCB with markings for serial port**+ 
 + 
 +{{ :media:tplink:tp_link_mr200_v4_serial.jpg?nolink&400 |}} 
 + 
 +{{ :media:tplink:mr_200_v4_serial_connection.jpg?nolink&400 |}}
  
-<WRAP BOX> 
-FIXME //Replace EXAMPLE by real values.// 
-</WRAP> 
  
-^ Serial connection parameters\\ for TP-Link MR200 v4 | EXAMPLE 115200, 8N1 |+^ Serial connection parameters\\ for TP-Link MR200 v4 | 115200, 8N1 |
  
 ==== JTAG ==== ==== JTAG ====
Line 178: Line 176:
 ==== OEM bootlog ==== ==== OEM bootlog ====
 <WRAP bootlog> <WRAP bootlog>
-<nowiki>COPY HERE THE BOOTLOG WITH THE ORIGINAL FIRMWARE</nowiki>+<nowiki>[04000D0B][04000D08] 
 +DDR Calibration DQS reg = 00008889 
 + 
 + 
 +U-Boot 1.1.3 (Oct 22 2018 - 11:01:41) 
 + 
 +Board: Ralink APSoC DRAM:  64 MB 
 +relocate_code Pointer at: 83fb4000 
 +gpiomode1 55154404. 
 +gpiomode2 05550555. 
 +######GPIO CTRL 0 for GPIO 0~31 OUTPUT tmp(0x00000030)##### 
 +######GPIO CTRL 1 for GPIO 32~64 OUTPUT tmp(0x00000f80)##### 
 +######GPIO CTRL 1 for GPIO 32~64 INPUT tmp(0x00000f80)##### 
 +flash manufacture id: ef, device id 40 17 
 +find flash: W25Q64BV 
 +============================================  
 +Ralink UBoot Version: 4.3.0.0 
 +--------------------------------------------  
 +ASIC 7628_MP (Port5<->None) 
 +DRAM component: 512 Mbits DDR, width 16 
 +DRAM bus: 16 bit 
 +Total memory: 64 MBytes 
 +Flash component: SPI Flash 
 +Date:Oct 22 2018  Time:11:01:41 
 +============================================  
 +icache: sets:512, ways:4, linesz:32 ,total:65536 
 +dcache: sets:256, ways:4, linesz:32 ,total:32768  
 + 
 + ##### The CPU freq = 580 MHZ ####  
 + estimate memory size =64 Mbytes 
 +RESET MT7628 PHY!!!!!! 
 +continue to starting system. 
 + 0  
 +disable switch phyport... 
 +    
 +3: System Boot system code via Flash.(0xbc020000) 
 +do_bootm:argc=2, addr=0xbc020000 
 +## Booting image at bc020000 ... 
 +   Uncompressing Kernel Image ... OK 
 +No initrd 
 +## Transferring control to Linux (at address 8000c150) ... 
 +## Giving linux memsize in MB, 64 
 + 
 +Starting kernel ... 
 + 
 +怘�������ff�fa�~�~f�`�������怘�怘�f30f�`� 
 +                                         �`��f��f���Linux version 2.6.36 (tp-link@Sohoidev) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 Mon Oct 22 11:05:26 CST 2018 
 + 
 + The CPU feqenuce set to 575 MHz 
 + 
 + MIPS CPU sleep mode enabled. 
 +CPU revision is: 00019655 (MIPS 24Kc) 
 +Software DMA cache coherency 
 +Determined physical RAM map: 
 + memory: 04000000 @ 00000000 (usable) 
 +Initrd not found or empty - disabling initrd 
 +Zone PFN ranges: 
 +  Normal   0x00000000 -> 0x00004000 
 +Movable zone start PFN for each node 
 +early_node_map[1] active PFN ranges 
 +    0: 0x00000000 -> 0x00004000 
 +Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256 
 +Kernel command line: console=ttyS1,115200 root=/dev/mtdblock2 rootfstype=squashfs init=/sbin/init 
 +PID hash table entries: 256 (order: -2, 1024 bytes) 
 +Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) 
 +Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) 
 +Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes. 
 +Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes 
 +Writing ErrCtl register=00039563 
 +Readback ErrCtl register=00039563 
 +Memory: 60868k/65536k available (2917k kernel code, 4668k reserved, 715k data, 184k init, 0k highmem) 
 +NR_IRQS:128 
 +console [ttyS1] enabled 
 +Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) 
 +pid_max: default: 4096 minimum: 301 
 +Mount-cache hash table entries: 512 
 +NET: Registered protocol family 16 
 +RALINK_GPIOMODE = 55154404  
 +RALINK_GPIOMODE = 55144404  
 +***** Xtal 40MHz ***** 
 +start PCIe register access 
 +RALINK_RSTCTRL = 2400000 
 +RALINK_CLKCFG1 = fdbfffc0 
 + 
 +*************** MT7628 PCIe RC mode ************* 
 +PCIE0 enabled 
 +Port 0 N_FTS = 1b105000 
 +init_rt2880pci done 
 +bio: create slab <bio-0> at 0 
 +usbcore: registered new interface driver usbfs 
 +usbcore: registered new interface driver hub 
 +usbcore: registered new device driver usb 
 +pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) 
 +pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] 
 +pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] 
 +pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff] 
 +pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff] 
 +pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x20000000-0x200fffff] 
 +pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff] 
 +pci 0000:01:00.1: BAR 0: set to [mem 0x20100000-0x201fffff] (PCI address [0x20100000-0x201fffff] 
 +pci 0000:00:00.0: PCI bridge to [bus 01-01] 
 +pci 0000:00:00.0:   bridge window [io  disabled] 
 +pci 0000:00:00.0:   bridge window [mem 0x20000000-0x201fffff] 
 +pci 0000:00:00.0:   bridge window [mem pref disabled] 
 +BAR0 at slot 0 = 0 
 +bus=0x0, slot = 0x0 
 +res[0]->start = 0 
 +res[0]->end = 0 
 +res[1]->start = 20200000 
 +res[1]->end = 2020ffff 
 +res[2]->start = 0 
 +res[2]->end = 0 
 +res[3]->start = 0 
 +res[3]->end = 0 
 +res[4]->start = 0 
 +res[4]->end = 0 
 +res[5]->start = 0 
 +res[5]->end = 0 
 +bus=0x1, slot = 0x0 
 +res[0]->start = 20000000 
 +res[0]->end = 200fffff 
 +res[1]->start = 0 
 +res[1]->end = 0 
 +res[2]->start = 0 
 +res[2]->end = 0 
 +res[3]->start = 0 
 +res[3]->end = 0 
 +res[4]->start = 0 
 +res[4]->end = 0 
 +res[5]->start = 0 
 +res[5]->end = 0 
 +bus=0x1, slot = 0x0 
 +res[0]->start = 20100000 
 +res[0]->end = 201fffff 
 +res[1]->start = 0 
 +res[1]->end = 0 
 +res[2]->start = 0 
 +res[2]->end = 0 
 +res[3]->start = 0 
 +res[3]->end = 0 
 +res[4]->start = 0 
 +res[4]->end = 0 
 +res[5]->start = 0 
 +res[5]->end = 0 
 +Switching to clocksource Ralink Systick timer 
 +NET: Registered protocol family 2 
 +IP route cache hash table entries: 1024 (order: 0, 4096 bytes) 
 +TCP established hash table entries: 2048 (order: 2, 16384 bytes) 
 +TCP bind hash table entries: 2048 (order: 1, 8192 bytes) 
 +TCP: Hash tables configured (established 2048 bind 2048) 
 +TCP reno registered 
 +NET: Registered protocol family 1 
 +RT3xxx EHCI/OHCI init. 
 +squashfs: version 4.0 (2009/01/31) Phillip Lougher 
 +fuse init (API version 7.15) 
 +msgmni has been set to 118 
 +io scheduler noop registered 
 +io scheduler deadline registered (default) 
 +Ralink gpio driver initialized 
 +i2cdrv_major = 218 
 +Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled 
 +serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A 
 +serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A 
 +brd: module loaded 
 +flash manufacture id: ef, device id 40 17 
 +W25Q64BV(ef 40170000 flash_version = 1) (8192 Kbytes) 
 +mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 
 +Creating 6 MTD partitions on "raspi": 
 +0x000000000000-0x000000020000 : "boot" 
 +0x000000020000-0x000000160000 : "kernel" 
 +0x000000160000-0x0000007d0000 : "rootfs" 
 +mtd: partition "rootfs" set to be root filesystem 
 +0x0000007d0000-0x0000007e0000 : "config" 
 +0x0000007e0000-0x0000007f0000 : "romfile" 
 +0x0000007f0000-0x000000800000 : "radio" 
 +Register flash device:flash0 
 +PPP generic driver version 2.4.2 
 +PPP MPPE Compression module registered 
 +NET: Registered protocol family 24 
 +PPTP driver version 0.8.5 
 +tun: Universal TUN/TAP device driver, 1.6 
 +tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> 
 +ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver 
 +FM_OUT value: u4FmOut = 0(0x00000000) 
 +FM_OUT value: u4FmOut = 126(0x0000007E) 
 +FM detection done! loop = 1 
 +SR calibration value u1SrCalVal = 7 
 +rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller 
 +rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 
 +rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 
 +rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00 
 +hub 1-0:1.0: USB hub found 
 +hub 1-0:1.0: 1 port detected 
 +ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver 
 +rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller 
 +rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 
 +rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 
 +hub 2-0:1.0: USB hub found 
 +hub 2-0:1.0: 1 port detected 
 +Mirror/redirect action on 
 +u32 classifier 
 +    Actions configured 
 +Netfilter messages via NETLINK v0.30. 
 +nf_conntrack version 0.5.0 (951 buckets, 3804 max) 
 +GRE over IPv4 demultiplexor driver 
 +gre: can't add protocol 
 +GRE over IPv4 tunneling driver 
 +ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux 
 +TCP cubic registered 
 +NET: Registered protocol family 10 
 +ip6_tables: (C) 2000-2006 Netfilter Core Team 
 +IPv6 over IPv4 tunneling driver 
 +NET: Registered protocol family 17 
 +NET: Registered protocol family 15 
 +Ebtables v2.0 registered 
 +802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> 
 +All bugs added by David S. Miller <davem@redhat.com> 
 +VFS: Mounted root (squashfs filesystem) readonly on device 31:2. 
 +Freeing unused kernel memory: 184k freed 
 +starting pid 35, tty '': '/etc/init.d/rcS' 
 +cp: can't stat '/etc/SingleSKU_FCC.dat': No such file or directory 
 +SCSI subsystem initialized 
 +insmod: can't insert '/lib/modules/kmdir/kernel/drivers/usb/core/usbcore.ko': No such file or directory 
 +Initializing USB Mass Storage driver... 
 +usbcore: registered new interface driver usb-storage 
 +USB Mass Storage support registered. 
 +insmod: can't insert '/lib/modules/kmdir/kernel/drivers/usb/host/ifxusb_host.ko': No such file or directory 
 +rdm_major = 253 
 +spiflash_ioctl_read, Read from 0x007ef100 length 0x6, ret 0, retlen 0x6 
 +Read MAC from flash(0x7EF100) ffffffd8-0d-17-02-40-ffffff9b 
 +GMAC1_MAC_ADRH -- : 0x0000d80d 
 +GMAC1_MAC_ADRL -- : 0x1702409b 
 +Ralink APSoC Ethernet Driver Initilization. v3.1  256 rx/tx descriptors allocated, mtu = 1500! 
 +spiflash_ioctl_read, Read from 0x007ef100 length 0x6, ret 0, retlen 0x6 
 +Read MAC from flash(0x7EF100) ffffffd8-0d-17-02-40-ffffff9b 
 +GMAC1_MAC_ADRH -- : 0x0000d80d 
 +GMAC1_MAC_ADRL -- : 0x1702409b 
 +PROC INIT OK! 
 +usbcore: registered new interface driver cdc_wdm 
 +usbcore: registered new interface driver qmi_wwan 
 +usbcore: registered new interface driver usbserial 
 +USB Serial support registered for generic 
 +usbcore: registered new interface driver usbserial_generic 
 +usbserial: USB Serial Driver core 
 +dns_init 
 +domain_name:tplinkmodem.net 
 +L2TP core driver, V2.0 
 +PPPoL2TP kernel driver, V2.0 
 +[err] syslogd[main --763] syslogd : syslogd_init 
 + 
 +usb 1-1: new high speed USB device using rt3xxx-ehci and address 2 
 +[zc] qmi_wwan_bind: in 
 +[zc] change dtr 1 
 +spiflash_ioctl_read, Read from 0x007ef100 length 0x6, ret 0, retlen 0x6 
 +Init mac d8-0d-17-02-40-9c 
 +qmi_wwan: probe of 1-1:1.0 failed with error -22 
 +usbserial_generic 1-1:1.0: generic converter detected 
 +usb 1-1: generic converter now attached to ttyUSB0 
 +[zc] qmi_wwan_bind: in 
 +[zc] change dtr 1 
 +spiflash_ioctl_read, Read from 0x007ef100 length 0x6, ret 0, retlen 0x6 
 +Init mac d8-0d-17-02-40-9c 
 +qmi_wwan: probe of 1-1:1.1 failed with error -22 
 +qmi_wwan 1-1:1.2: bogus CDC Union: master=0, slave=0 
 +qmi_wwan: probe of 1-1:1.2 failed with error -1 
 +qmi_wwan 1-1:1.3: bogus CDC Union: master=0, slave=0 
 +qmi_wwan: probe of 1-1:1.3 failed with error -1 
 +qmi_wwan 1-1:1.4: cdc-wdm0: USB WDM device 
 +[zc] qmi_wwan_bind: in 
 +[zc] change dtr 1 
 +spiflash_ioctl_read, Read from 0x007ef100 length 0x6, ret 0, retlen 0x6 
 +Init mac d8-0d-17-02-40-9c 
 +scsi0 : usb-storage 1-1:1.5 
 +scsi 0:0:0:0: Direct-Access     Linux    File-Stor Gadget 0318 PQ: 0 ANSI: 2 
 +sd 0:0:0:0: [sda] 130048 512-byte logical blocks: (66.5 MB/63.5 MiB) 
 +sd 0:0:0:0: [sda] Write Protect is off 
 +sd 0:0:0:0: [sda] Assuming drive cache: write through 
 +sd 0:0:0:0: [sda] Assuming drive cache: write through 
 + sda: 
 +sd 0:0:0:0: [sda] Assuming drive cache: write through 
 +sd 0:0:0:0: [sda] Attached SCSI removable disk 
 +linux_qmi_qmux_io_pwr_up_init.c: Unable to open wakelock file = /sys/power/wake_lock, error [2:No such file or directory] 
 +qmuxd: linux_qmi_read_sysfs_config: couldn't open file /sys/module/f_rmnet/parameters/rmnet_ctl_chqmuxd: linux_qmi_read_sysfs_config: couldn't open /sys/module/rmnet/parameters/rmnet_ctl_chlinux_qmi_qmux_if_configure_port_timeout: failed to open SMD timeout config=/sys/devices/virtual/smdpkt/cdc-wdm0/open_timeout errno [2:No such file or directory]linux_qmi_qmux_if_configure_port_timeout: failed to open SMD timeout config=/sys/devices/virtual/smdpkt/cdc-wdm0/open_timeout errno [2:No such file or directory]qmi_qmux_open_connection: connection is disabled for conn_id=1 
 +qmuxd: opening connection for conn_id=1 [DATA6_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=2 
 +qmuxd: opening connection for conn_id=2 [DATA7_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=3 
 +qmuxd: opening connection for conn_id=3 [DATA8_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=4 
 +qmuxd: opening connection for conn_id=4 [DATA9_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=5 
 +qmuxd: opening connection for conn_id=5 [DATA12_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=6 
 +qmuxd: opening connection for conn_id=6 [DATA13_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=7 
 +qmuxd: opening connection for conn_id=7 [DATA14_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=9 
 +qmuxd: opening connection for conn_id=9 [DATA15_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=10 
 +qmuxd: opening connection for conn_id=10 [DATA16_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=11 
 +qmuxd: opening connection for conn_id=11 [DATA17_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=21 
 +qmuxd: opening connection for conn_id=21 [SDIO_DATA1_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=22 
 +qmuxd: opening connection for conn_id=22 [SDIO_DATA2_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=23 
 +qmuxd: opening connection for conn_id=23 [SDIO_DATA3_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=24 
 +qmuxd: opening connection for conn_id=24 [SDIO_DATA4_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=25 
 +qmuxd: opening connection for conn_id=25 [SDIO_DATA5_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=26 
 +qmuxd: opening connection for conn_id=26 [SDIO_DATA6_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=27 
 +qmuxd: opening connection for conn_id=27 [SDIO_DATA7_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=28 
 +qmuxd: opening connection for conn_id=28 [SDIO_DATA8_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=29 
 +qmuxd: opening connection for conn_id=29 [MDM_DATA1_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=30 
 +qmuxd: opening connection for conn_id=30 [MDM_DATA2_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=31 
 +qmuxd: opening connection for conn_id=31 [MDM_DATA3_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=32 
 +qmuxd: opening connection for conn_id=32 [MDM_DATA4_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=33 
 +qmuxd: opening connection for conn_id=33 [MDM_DATA5_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=34 
 +qmuxd: opening connection for conn_id=34 [MDM_DATA6_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=35 
 +qmuxd: opening connection for conn_id=35 [MDM_DATA7_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=36 
 +qmuxd: opening connection for conn_id=36 [MDM_DATA8_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=48 
 +qmuxd: opening connection for conn_id=48 [SMUX0] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=49 
 +qmuxd: opening connection for conn_id=49 [MDM2_DATA1_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=50 
 +qmuxd: opening connection for conn_id=50 [MDM2_DATA2_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=51 
 +qmuxd: opening connection for conn_id=51 [MDM2_DATA3_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=52 
 +qmuxd: opening connection for conn_id=52 [MDM2_DATA4_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=53 
 +qmuxd: opening connection for conn_id=53 [MDM2_DATA5_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=54 
 +qmuxd: opening connection for conn_id=54 [MDM2_DATA6_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=55 
 +qmuxd: opening connection for conn_id=55 [MDM2_DATA7_CNTL] failed 
 +qmi_qmux_open_connection: connection is disabled for conn_id=56 
 +qmuxd: opening connection for conn_id=56 [MDM2_DATA8_CNTL] failed 
 + 
 +Please press Enter to activate this console. qmi_ctl_rx_msg.c Can't find txn info for txn_id = 1 
 +[ dm_readFile ] 2042:  can not open xml file /var/tmp/pc/reduced_data_model.xml!, about to open file /etc/reduced_data_model.xml 
 +[ judgeProductName ] 2157:  Device is MR200 
 + 
 +[ judgeProductName ] 2190:  Device is MR200v4 
 + 
 +[ dm_readFile ] 2042:  can not open xml file /var/tmp/pc/reduced_data_model_MR200V4.xml!, about to open file /etc/reduced_data_model_MR200V4.xml 
 +spiflash_ioctl_read, Read from 0x007d0000 length 0x10000, ret 0, retlen 0x10000 
 +spiflash_ioctl_read, Read from 0x007d0000 length 0x7567, ret 0, retlen 0x7567 
 +spiflash_ioctl_read, Read from 0x007d0000 length 0x10000, ret 0, retlen 0x10000 
 +spiflash_ioctl_read, Read from 0x007d0000 length 0x7567, ret 0, retlen 0x7567 
 +[ checkUdiskReady ] 069:  [cos] times:0, mount cmd:mount -t auto /dev/sda /tmp/udisk 
 + 
 +FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive! 
 +spiflash_ioctl_read, Read from 0x007ef500 length 0x29, ret 0, retlen 0x29 
 +17 INFO: src/flospiflash_ioctl_read, Read from 0x007ef100 length 0x6, ret 0, retlen 0x6 
 +wstat_main.c(18) main(): LTE flospiflash_ioctl_read, Read from 0x007ef200 length 0x4, ret 0, retlen 0x4 
 +wstat process starts working! 
 +1spiflash_ioctl_read, Read from 0x00020000 length 0x200, ret 0, retlen 0x200 
 +7 ERROR: Post evspiflash_ioctl_read, Read from 0x007ef100 length 0x6, ret 0, retlen 0x6 
 +ent to MOBILE server failed, errno = 2 (No such file or directory). 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +17 ERROR: Client communication with server failed. 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +17 ERROR: src/flowstat_manage.c(73) flowstat_get_wwan_tx_rx_statistics(): Get Rx/Tx flow from qmi failed! 
 +Raeth v3.1 (Tasklet,SkbRecycle) 
 + 
 +phy_tx_ring = 0x036ec000, tx_ring = 0xa36ec000 
 + 
 +phy_rx_ring0 = 0x036ed000, rx_ring0 = 0xa36ed000 
 +[fe_sw_init:4952]rt305x_esw_init. 
 +disable switch phyport... 
 +GMAC1_MAC_ADRH -- : 0x0000d80d 
 +GMAC1_MAC_ADRL -- : 0x1702409b 
 +RT305x_ESW: Link Status Changed 
 +18 ERROR: Post event to MOBILE server failed, erspiflash_ioctl_read, Read from 0x007ef600 length 0xf, ret 0, retlen 0xf 
 +rno = 2 (No such file or directory). 
 +18 ERROR: Client communication with server failed. 
 +18 ERROR: Post event to MOBILE server failed, errno = 2 (No such file or directory). 
 +18 ERROR: Client communication with server failed. 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +Query new SMS count success.18 ERROR: New sms count is 0 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +18 USER: Mobile device manager (qmi) initialized OK. 
 +Init QMI services...... 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +19 USER: Start get voice service object. 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +19 USER: VOICE Service Object got. 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +19 USER: VOICE QMI Client Init successfully, handle is 0x004A7C48. 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +19 USER: Mobile device manager (qmi) initialized OK. 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +21 USER: Not registered, searching! 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +1451606421 ERROR: 0x00000034 QMI_ERR_DEVICE_NOT_READY 
 +1451606421 ERROR: Failed to get smsc address (0). 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +[err] syslogd[syslogd_msg_process --652] syslogd : log module is not config 
 + 
 +spiflash_ioctl_read, Read from 0x007ef600 length 0xf, ret 0, retlen 0xf 
 +sendto /var/tmp/7 msg 2001 error No such file or directory ,pid 106 
 +[ oal_sys_getOldTZInfo ] 732:  Open TZ file error! 
 +Fri Jan  1 01:00:21 UTC 2016 
 +sh: can't create /proc/tplink/eth_vlan: nonexistent directory 
 +ioctl: No such device 
 +Fri Jan  1 01:00:21 UTC 2016 
 +brctl: bridge br0: Invalid argument 
 +set if eth0.2 to *not wan dev 
 +device eth0.2 entered promiscuous mode 
 +device eth0 entered promiscuous mode 
 +br0: port 1(eth0.2) entering forwarding state 
 +br0: port 1(eth0.2) entering forwarding state 
 +set if eth0.3 to *not wan dev 
 +device eth0.3 entered promiscuous mode 
 +br0: port 2(eth0.3) entering forwarding state 
 +br0: port 2(eth0.3) entering forwarding state 
 +set if eth0.4 to *not wan dev 
 +device eth0.4 entered promiscuous mode 
 +br0: port 3(eth0.4) entering forwarding state 
 +br0: port 3(eth0.4) entering forwarding state 
 +set if eth0.5 to *not wan dev 
 +device eth0.5 entered promiscuous mode 
 +br0: port 4(eth0.5) entering forwarding state 
 +br0: port 4(eth0.5) entering forwarding state 
 +set if eth0.5 to wan dev 
 +[ vlan_addLanPortsIntoBridge ] 512:  add lan Port 255 from br0 
 +brctl: bridge br0: Device or resource busy 
 +brctl: bridge br0: Device or resource busy 
 +brctl: bridge br0: Device or resource busy 
 +brctl: bridge br0: Device or resource busy 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +ra0       no private ioctls. 
 + 
 + 
 + 
 +=== pAd = c0c28000, size = 914848 === 
 + 
 +<-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x 
 +<-- RTMPAllocAdapterBlock, Status=0 
 +RtmpChipOpsHook(492): Not support for HIF_MT yet! 
 +mt7628_init()--> 
 +mt7628_init(FW(8a00), HW(8a01), CHIPID(7628)) 
 +e2.bin mt7628_init(1135)::(2), pChipCap->fw_len(64736) 
 +mt_bcn_buf_init(218): Not support for HIF_MT yet! 
 +<--mt7628_init() 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +Interface doesn't accept private ioctl... 
 +set (8BE2): Network is down 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +[ oal_wlan_ra_lteCoexistence ] 6899:  Get Curr band err 0. 
 + 
 +No need to switch channel. 
 +[ oal_sht:pAd->ApBootFlag = TRUE 
 +wlan_ra_lteCoexiTX_BCN DESC a2127000 size = 320 
 +stence ] 6989:  RX[0] DESC a212b000 size = 4096 
 + 
 +AutoChannelSkiRX[1] DESC a212e000 size = 2048 
 +pList = 12;13;52;56;60;64;100;104;108;112;116;120;124;128;132;136;140 
 + 
 +cfg_mode=9 
 +cfg_mode=9 
 +wmode_band_equal(): Band Equal! 
 +AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD 
 +APSDCapable[0]=0 
 +APSDCapable[1]=0 
 +APSDCapable[2]=0 
 +APSDCapable[3]=0 
 +APSDCapable[4]=0 
 +APSDCapable[5]=0 
 +APSDCapable[6]=0 
 +APSDCapable[7]=0 
 +APSDCapable[8]=0 
 +APSDCapable[9]=0 
 +APSDCapable[10]=0 
 +APSDCapable[11]=0 
 +APSDCapable[12]=0 
 +APSDCapable[13]=0 
 +APSDCapable[14]=0 
 +APSDCapable[15]=0 
 +Key1Str is Invalid key length(0) or Type(0) 
 +Key1Str is Invalid key length(0) or Type(0) 
 +Key2Str is Invalid key length(0) or Type(0) 
 +Key2Str is Invalid key length(0) or Type(0) 
 +Key3Str is Invalid key length(0) or Type(0) 
 +Key3Str is Invalid key length(0) or Type(0) 
 +Key4Str is Invalid key length(0) or Type(0) 
 +Key4Str is Invalid key length(0) or Type(0) 
 +WscKeyASCII=8 
 +WscKeyASCII=8 
 +load fw image from fw_header_image 
 +AndesMTLoadFwMethod1(2261)::pChipCap->fw_len(64736) 
 +FW Version:1 
 +FW Build Date:20170411104110 
 +CmdAddressLenReq:(ret = 0) 
 +CmdFwStartReq: override = 1, address = 1048576 
 +CmdStartDLRsp: WiFI FW Download Success 
 +MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC) 
 +efuse_probe: efuse = 10000002 
 +RtmpChipOpsEepromHook::e2p_type=2, inf_Type=4 
 +RtmpEepromGetDefault::e2p_dafault=2 
 +RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2 
 +NVM is FLASH mode 
 +1. Phy Mode = 14 
 +exec! 
 +spiflash_ioctl_read, Read from 0x007f0000 length 0x400, ret 0, retlen 0x400 
 +eeFlashId = 0x7628! 
 +Country Region from e2p = ffff 
 +tssi_1_target_pwr_g_band = 30 
 +2. Phy Mode = 14 
 +3. Phy Mode = 14 
 +NICInitPwrPinCfg(11): Not support for HIF_MT yet! 
 +NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet! 
 +mt_mac_init()--> 
 +MtAsicInitMac()--> 
 +mt7628_init_mac_cr()--> 
 +MtAsicSetMacMaxLen(1277): Set the Max RxPktLen=450! 
 +<--mt_mac_init() 
 + WTBL Segment 1 info: 
 + MemBaseAddr/FID:0x28000/
 + EntrySize/Cnt:32/128 
 + WTBL Segment 2 info: 
 + MemBaseAddr/FID:0x40000/
 + EntrySize/Cnt:64/128 
 + WTBL Segment 3 info: 
 + MemBaseAddr/FID:0x42000/64 
 + EntrySize/Cnt:64/128 
 + WTBL Segment 4 info: 
 + MemBaseAddr/FID:0x44000/128 
 + EntrySize/Cnt:32/128 
 +AntCfgInit(2943): Not support for HIF_MT yet! 
 +MCS Set = ff ff 00 00 01 
 +MtAsicSetChBusyStat(861): Not support for HIF_MT yet! 
 +[PMF]ap_pmf_init:: apidx=0, MFPC=0, MFPR=0, SHA256=0 
 +[PMF]RTMPMakeRsnIeCap: RSNIE Capability MFPC=0, MFPR=0 
 +[PMF]ap_pmf_init:: apidx=1, MFPC=0, MFPR=0, SHA256=0 
 +MtAsicSetRalinkBurstMode(3145): Not support for HIF_MT yet! 
 +MtAsicSetPiggyBack(796): Not support for HIF_MT yet! 
 +reload DPD from flash , 0x9F = [c000] doReload bit7[0] 
 +CmdLoadDPDDataFromFlash: Channel = 2, DoReload = 0 
 +MtAsicSetTxPreamble(3124): Not support for HIF_MT yet! 
 +CmdSlotTimeSet:(ret = 0) 
 +MtAsicAddSharedKeyEntry(1344): Not support for HIF_MT yet! 
 +The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2 
 +MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0 
 +Main bssid = d8:0d:17:02:40:9b 
 +<==== rt28xx_init, Status=0 
 +@@@ ed_monitor_init : ===> 
 +@@@ ed_monitor_init : <=== 
 +mt7628_set_ed_cca: TURN ON EDCCA mac 0x10618 = 0xd7c87d0f, EDCCA_Status=1 
 +sht:pAd->ApBootFlag = FALSE 
 +WiFi Startup Cost (ra0): 3.768s 
 +Set_ed_chk_proc()::ed_chk=0 
 +mt7628_set_ed_cca: TURN OFF EDCCA  mac 0x10618 = 0xd7083f0f, EDCCA_Status=0 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2 
 +:  Device is MR200v4 
 + 
 +ra0 RTMPInfClose done. 
 +MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0x0 
 +MtAsicSetPiggyBack(796): Not support for HIF_MT yet! 
 +tx_kickout_fail_count = 0 
 +tx_timeout_fail_count = 0 
 +rx_receive_fail_count = 0 
 +alloc_cmd_msg = 159 
 +free_cmd_msg = 159 
 +device ra0 entered promiscuous mode 
 +device ra1 entered promiscuous mode 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +WLAN-Start wlNetlinkTool 
 +Waiting for Wireless Events from interfaces... 
 +swWlanChkAhbErr: netlink to do 
 +rai0      no private ioctls. 
 + 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +spiflash_ioctl_read, Read from 0x007f0000 length 0x10000, ret 0, retlen 0x10000 
 +read radio success, offset 0x7f8000, size 0x400 
 +eeFlashId = 0x7610! 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +Interface doesn't accept private ioctl... 
 +set (8BE2): Network is down 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +load fw spent 16ms 
 +[ oal_wlan_ra_setWpsUPnP ] 6297:  rai0: cannot open scpd xml file 
 + 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +0x1300 = 00064300 
 +Interface doesn't accept private ioctl... 
 +set (8BE2): Invalid argument 
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +spiflash_ioctl_read, Read from 0x007f0000 length 0x10000, ret 0, retlen 0x10000 
 +read radio success, offset 0x7f8000, size 0x400 
 +eeFlashId = 0x7610! 
 +device rai0 entered promiscuous mode 
 +device rai1 entered promiscuous mode 
 +wlNetlinkTool is already there.  
 +[ util_judgeProductName ] 601:  Device is MR200 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 106 
 +sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 106 
 +sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 106 
 +[src/cloud_downloadHandler.c:cloud_initPthreadDownloadHandler:241] init download handler success! 
 + 
 +[src/cloud_downloadHandler.c:downloadHandler:104] Enter download handler, download firmware from cloud... 
 + 
 +[src/cloud_downloadHandler.c:downloadHandler:108] wait semaphore to download firmware to device... 
 + 
 +mmmInit():Total mem size=51364, addr=0x0x446150. 
 +************************************************************* 
 +*************************MMM TABLE DUMP********************** 
 +------------------------------------------------------------- 
 + poolhead(40)  poolnum  dynamictimes  chainhead  poolend      
 +------------------------------------------------------------- 
 + 0x446150        8          0         (nil)     0x4529f4   
 +------------------------------------------------------------- 
 + index  poolhead(20)    size    blocks    free     usage   
 +------------------------------------------------------------- 
 +  1     0x446178        32          256       256                
 +  2     0x448590        64          128       128                
 +  3     0x44a7a8        128         64        64        0          
 +  4     0x44c8c0        256         32        32        0          
 +  5     0x44e958        512                                  
 +  6     0x44f990        1024        4                          
 +  7     0x4509b8        2048        2                          
 +  8     0x4519d8        4096        1                          
 +------------------------------------------------------------- 
 + index  chainnode(16)   magic    length    prev    next       
 +------------------------------------------------------------- 
 +(nil) 
 +************************************************************* 
 +sendto /var/tmp/8 msg 2030 error No such file or directory ,pid 106 
 +sendto /var/tmp/9 msg 2004 error No such file or directory ,pid 106 
 +insmod: can't insert '/lib/modules/kmdir/kernel/drivers/net/tun.ko': No such file or directory 
 +insmod: can't insert '/lib/modules/kmdir/kernel/drivers/net/ppp_mppe.ko': No such file or directory 
 +lin: oal_WritePptpVpnFile start! 
 +iptables: Bad rule (does a matching rule exist in that chain?). 
 +killall: npd6: no process killed 
 +radvd starting 
 +iptables: Bad rule (does a matching rule exist in that chain?). 
 +[rsl_initWanLteIntfCfgObj 3263] init LTE module, set flowstat [enableDataLimit 0, enablePaymentDay 0, paymentDay 1, limitation 0, warningPercent 90] 
 +[initProfileList 413] LTE Module: profile num [1], default profile [0], active profile [0] 
 +[initProfileList 415] DM: profile num [1], default profile [0], active profile [0] 
 +/var/run/dhcp6c_wwan0.pid: No such file or directory 
 +[ getPidFromPidFile ] 112:  Cann't open file: /var/run/zebra.pid. 
 +[ getPidFromPidFile ] 112:  Cann't open file: /var/run/ripd.pid. 
 +iptables: Bad rule (does a matching rule exist in that chain?). 
 +iptables: Bad rule (does a matching rule exist in that chain?). 
 +iptables: Bad rule (does a matching rule exist in that chain?). 
 +[src/cloud_client.c:initSigIntHandler:104] init signal handler success! 
 + 
 +[src/cloud_client.c:cloudClientInit:148] Init cloud-client environment successful. 
 + 
 +[src/cloud_localMsgHandler.c:cloud_localMsgTask:96] Start cloud local message observer... 
 + 
 +nf_nat_rtsp v0.6.21 loading 
 +iptables: Bad rule (does a matching rule exist in that chain?). 
 +ip6tables: Bad rule (does a matching rule exist in that chain?). 
 +ip6tables: Bad rule (does a matching rule exist in that chain?). 
 +enable switch phyport...] 601:  Device is MR200 
 + 
 + 
 +[ util_judgeProductName ] 634:  Device is MR200v4 
 + 
 +Set: phy[0].reg[0] = 3900 
 +Set: phy[1].reg[0] = 3900 
 +Set: phy[2].reg[0] = 3900 
 +Set: phy[3].reg[0] = 3900 
 +Set: phy[4].reg[0] = 3900 
 +Set: phy[0].reg[0] = 3300 
 +Set: phy[1].reg[0] = 3300 
 +Set: phy[2].reg[0] = 3300 
 +Set: phy[3].reg[0] = 3300 
 +Set: phy[4].reg[0] = 3300 
 +resetMiiPortV over. 
 +Set: phy[0].reg[4] = 01e1 
 +Set: phy[0].reg[0] = 3300 
 +Set: phy[1].reg[4] = 01e1 
 +Set: phy[1].reg[0] = 3300 
 +Set: phy[2].reg[4] = 01e1 
 +Set: phy[2].reg[0] = 3300 
 +Set: phy[3].reg[4] = 01e1 
 +Set: phy[3].reg[0] = 3300 
 +Set: phy[4].reg[4] = 01e1 
 +Set: phy[4].reg[0] = 3300 
 +turn off flow control over. 
 +</nowiki>
 </WRAP>\\ </WRAP>\\
  
 ==== OpenWrt bootlog ==== ==== OpenWrt bootlog ====
 <WRAP bootlog> <WRAP bootlog>
-<nowiki>COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING</nowiki>+<nowiki>[04000D0B][04000D08] 
 + 
 +DDR Calibration DQS reg = 00008889 
 + 
 + 
 + 
 +U-Boot 1.1.3 (Oct 22 2018 - 11:01:41) 
 + 
 + 
 +Board: Ralink APSoC DRAM:  64 MB 
 + 
 +relocate_code Pointer at: 83fb4000 
 + 
 +gpiomode1 55154404. 
 + 
 +gpiomode2 05550555. 
 + 
 +######GPIO CTRL 0 for GPIO 0~31 OUTPUT tmp(0x00000030)##### 
 + 
 +######GPIO CTRL 1 for GPIO 32~64 OUTPUT tmp(0x00000f80)##### 
 + 
 +######GPIO CTRL 1 for GPIO 32~64 INPUT tmp(0x00000f80)##### 
 + 
 +flash manufacture id: ef, device id 40 17 
 + 
 +find flash: W25Q64BV 
 + 
 +============================================  
 + 
 +Ralink UBoot Version: 4.3.0.0 
 + 
 +--------------------------------------------  
 + 
 +ASIC 7628_MP (Port5<->None) 
 + 
 +DRAM component: 512 Mbits DDR, width 16 
 + 
 +DRAM bus: 16 bit 
 + 
 +Total memory: 64 MBytes 
 + 
 +Flash component: SPI Flash 
 + 
 +Date:Oct 22 2018  Time:11:01:41 
 + 
 +============================================  
 + 
 +icache: sets:512, ways:4, linesz:32 ,total:65536 
 + 
 +dcache: sets:256, ways:4, linesz:32 ,total:32768  
 + 
 + 
 + ##### The CPU freq = 580 MHZ ####  
 + 
 + estimate memory size =64 Mbytes 
 + 
 +RESET MT7628 PHY!!!!!! 
 + 
 +continue to starting system. 
 + 
 + 0  
 + 
 +disable switch phyport... 
 + 
 +    
 + 
 +3: System Boot system code via Flash.(0xbc020000) 
 + 
 +do_bootm:argc=2, addr=0xbc020000 
 + 
 +## Booting image at bc020000 ... 
 + 
 +   Uncompressing Kernel Image ... OK 
 + 
 +No initrd 
 + 
 +## Transferring control to Linux (at address 80000000) ... 
 + 
 +## Giving linux memsize in MB, 64 
 + 
 + 
 +Starting kernel ... 
 + 
 + 
 +[    0.000000] Linux version 4.14.105 (nsvee@halyard) (gcc version 7.4.0 (OpenWrt GCC 7.4.0 r9584-5107176861)) #0 Fri Mar 15 21:04:11 2019 
 +[    0.000000] Board has DDR2 
 +[    0.000000] Analog PMU set to hw control 
 +[    0.000000] Digital PMU set to hw control 
 +[    0.000000] SoC Type: MediaTek MT7628AN ver:1 eco:2 
 +[    0.000000] bootconsole [early0] enabled 
 +[    0.000000] CPU0 revision is: 00019655 (MIPS 24KEc) 
 +[    0.000000] MIPS: machine is TP-Link Archer MR200 V4 
 +[    0.000000] Determined physical RAM map: 
 +[    0.000000]  memory: 04000000 @ 00000000 (usable) 
 +[    0.000000] Initrd not found or empty - disabling initrd 
 +[    0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. 
 +[    0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes 
 +[    0.000000] Zone ranges: 
 +[    0.000000]   Normal   [mem 0x0000000000000000-0x0000000003ffffff] 
 +[    0.000000] Movable zone start for each node 
 +[    0.000000] Early memory node ranges 
 +[    0.000000]   node   0: [mem 0x0000000000000000-0x0000000003ffffff] 
 +[    0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] 
 +[    0.000000] random: get_random_bytes called from start_kernel+0x8c/0x474 with crng_init=0 
 +[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 16256 
 +[    0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 
 +[    0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) 
 +[    0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) 
 +[    0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) 
 +[    0.000000] Writing ErrCtl register=00039563 
 +[    0.000000] Readback ErrCtl register=00039563 
 +[    0.000000] Memory: 59784K/65536K available (3647K kernel code, 172K rwdata, 844K rodata, 192K init, 200K bss, 5752K reserved, 0K cma-reserved) 
 +[    0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 
 +[    0.000000] NR_IRQS: 256 
 +[    0.000000] intc: using register map from devicetree 
 +[    0.000000] CPU Clock: 580MHz 
 +[    0.000000] timer_probe: no matching timers found 
 +[    0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns 
 +[    0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns 
 +[    0.007539] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) 
 +[    0.073494] pid_max: default: 32768 minimum: 301 
 +[    0.078163] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) 
 +[    0.084517] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) 
 +[    0.096556] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns 
 +[    0.106050] futex hash table entries: 256 (order: -1, 3072 bytes) 
 +[    0.111989] pinctrl core: initialized pinctrl subsystem 
 +[    0.117522] NET: Registered protocol family 16 
 +[    0.229468] mt7620-pci 10140000.pcie: Port 0 N_FTS = 1b105000 
 +[    0.384754] PCI host bridge /pcie@10140000 ranges: 
 +[    0.389333]  MEM 0x0000000020000000..0x000000002fffffff 
 +[    0.394353]   IO 0x0000000010160000..0x000000001016ffff 
 +[    0.415451] mt7621_gpio 10000600.gpio: registering 32 gpios 
 +[    0.421089] mt7621_gpio 10000600.gpio: registering 32 gpios 
 +[    0.426597] mt7621_gpio 10000600.gpio: registering 32 gpios 
 +[    0.432758] PCI host bridge to bus 0000:00 
 +[    0.436661] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] 
 +[    0.443344] pci_bus 0000:00: root bus resource [io  0xffffffff] 
 +[    0.449002] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] 
 +[    0.455567] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] 
 +[    0.463631] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring 
 +[    0.472421] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] 
 +[    0.478751] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] 
 +[    0.485523] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] 
 +[    0.492024] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] 
 +[    0.498598] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff] 
 +[    0.505132] pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff] 
 +[    0.511698] pci 0000:00:00.0: PCI bridge to [bus 01] 
 +[    0.516470] pci 0000:00:00.0:   bridge window [mem 0x20000000-0x201fffff] 
 +[    0.527316] clocksource: Switched to clocksource MIPS 
 +[    0.533297] NET: Registered protocol family 2 
 +[    0.538284] TCP established hash table entries: 1024 (order: 0, 4096 bytes) 
 +[    0.544974] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) 
 +[    0.551163] TCP: Hash tables configured (established 1024 bind 1024) 
 +[    0.557446] UDP hash table entries: 256 (order: 0, 4096 bytes) 
 +[    0.563039] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) 
 +[    0.569380] NET: Registered protocol family 1 
 +[    0.576810] Crashlog allocated RAM at address 0x3f00000 
 +[    0.583388] workingset: timestamp_bits=30 max_order=14 bucket_order=0 
 +[    0.594889] squashfs: version 4.0 (2009/01/31) Phillip Lougher 
 +[    0.600519] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. 
 +[    0.619384] io scheduler noop registered 
 +[    0.623114] io scheduler deadline registered (default) 
 +[    0.628998] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled 
 +[    0.636179] console [ttyS0] disabled 
 +[    0.639684] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A 
 +[    0.648410] console [ttyS0] enabled 
 +[    0.648410] console [ttyS0] enabled 
 +[    0.655398] bootconsole [early0] disabled 
 +[    0.655398] bootconsole [early0] disabled 
 +[    0.663988] cacheinfo: Failed to find cpu0 device node 
 +[    0.669247] cacheinfo: Unable to detect cache hierarchy for CPU 0 
 +[    0.676108] spi-mt7621 10000b00.spi: sys_freq: 193333333 
 +[    0.694553] m25p80 spi0.0: s25fl064k (8192 Kbytes) 
 +[    0.699505] 5 fixed-partitions partitions found on MTD device spi0.0 
 +[    0.705942] Creating 5 MTD partitions on "spi0.0": 
 +[    0.710837] 0x000000000000-0x000000020000 : "u-boot" 
 +[    0.716738] 0x000000020000-0x0000007d0000 : "firmware" 
 +[    0.724913] 2 tplink-fw partitions found on MTD device firmware 
 +[    0.730991] Creating 2 MTD partitions on "firmware": 
 +[    0.736036] 0x000000000000-0x00000017f09e : "kernel" 
 +[    0.741978] 0x00000017f0a0-0x0000007b0000 : "rootfs" 
 +[    0.747828] mtd: device 3 (rootfs) set to be root filesystem 
 +[    0.754999] 1 squashfs-split partitions found on MTD device rootfs 
 +[    0.761356] 0x000000590000-0x0000007b0000 : "rootfs_data" 
 +[    0.767815] 0x0000007d0000-0x0000007e0000 : "rom" 
 +[    0.773375] 0x0000007e0000-0x0000007f0000 : "romfile" 
 +[    0.779398] 0x0000007f0000-0x000000800000 : "radio" 
 +[    0.785789] libphy: Fixed MDIO Bus: probed 
 +[    0.802335] rt3050-esw 10110000.esw: link changed 0x00 
 +[    0.809106] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 
 +[    0.819159] NET: Registered protocol family 10 
 +[    0.827379] Segment Routing with IPv6 
 +[    0.831209] NET: Registered protocol family 17 
 +[    0.835768] 8021q: 802.1Q VLAN Support v1.8 
 +[    0.850821] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. 
 +[    0.859088] Freeing unused kernel memory: 192K 
 +[    0.863590] This architecture does not have kernel memory protection. 
 +[    2.012791] init: Console is alive 
 +[    2.016488] init: - watchdog - 
 +[    2.317345] random: fast init done 
 +[    4.281780] kmodloader: loading kernel modules from /etc/modules-boot.d/
 +[    4.548208] usbcore: registered new interface driver usbfs 
 +[    4.553845] usbcore: registered new interface driver hub 
 +[    4.559412] usbcore: registered new device driver usb 
 +[    4.615315] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver 
 +[    4.631184] SCSI subsystem initialized 
 +[    4.640391] ehci-platform: EHCI generic platform driver 
 +[    4.656015] phy phy-10120000.usbphy.0: remote usb device wakeup disabled 
 +[    4.662829] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz 
 +[    4.668157] ehci-platform 101c0000.ehci: EHCI Host Controller 
 +[    4.674023] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 
 +[    4.682186] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 
 +[    4.717335] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 
 +[    4.724638] hub 1-0:1.0: USB hub found 
 +[    4.728887] hub 1-0:1.0: 1 port detected 
 +[    4.940169] usbcore: registered new interface driver usb-storage 
 +[    4.947012] kmodloader: done loading kernel modules from /etc/modules-boot.d/
 +[    4.957015] init: - preinit - 
 +[    6.306102] rt3050-esw 10110000.esw: link changed 0x00 
 +Press the [f] key and hit [enter] to enter failsafe mode 
 +Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level 
 +[    6.487245] random: procd: uninitialized urandom read (4 bytes read) 
 +[    6.677340] usb 1-1: new high-speed USB device number 2 using ehci-platform 
 +[    6.896704] usb-storage 1-1:1.5: USB Mass Storage device detected 
 +[    6.903827] scsi host0: usb-storage 1-1:1.5 
 +[    7.959897] scsi 0:0:0:0: Direct-Access     Linux    File-Stor Gadget 0318 PQ: 0 ANSI: 2 
 +[    7.974440] sd 0:0:0:0: [sda] 130048 512-byte logical blocks: (66.6 MB/63.5 MiB) 
 +[    7.982800] sd 0:0:0:0: [sda] Write Protect is off 
 +[    7.988552] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA 
 +[    8.013080]  sda: 
 +[    8.023804] sd 0:0:0:0: [sda] Attached SCSI removable disk 
 +[    9.724600] jffs2: notice: (421) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 1 orphan) and 1 of xref (1 dead, 0 orphan) found. 
 +[    9.742242] mount_root: switching to jffs2 overlay 
 +[    9.779352] overlayfs: upper fs does not support tmpfile. 
 +[    9.791055] urandom-seed: Seeding with /etc/urandom.seed 
 +[    9.875842] rt3050-esw 10110000.esw: link changed 0x04 
 +[    9.909052] procd: - early - 
 +[    9.912095] procd: - watchdog - 
 +[   10.523052] procd: - watchdog - 
 +[   10.526560] procd: - ubus - 
 +[   10.599008] random: ubusd: uninitialized urandom read (4 bytes read) 
 +[   10.773869] random: ubusd: uninitialized urandom read (4 bytes read) 
 +[   10.780919] random: ubusd: uninitialized urandom read (4 bytes read) 
 +[   10.788333] procd: - init - 
 +Please press Enter to activate this console. 
 +[   11.141092] kmodloader: loading kernel modules from /etc/modules.d/
 +[   11.155674] ip6_tables: (C) 2000-2006 Netfilter Core Team 
 +[   11.171861] usbcore: registered new interface driver cdc_wdm 
 +[   11.179905] Loading modules backported from Linux version v4.19.23-0-g67d52fae61c1 
 +[   11.187659] Backport generated by backports.git v4.19.23-1-0-g480a925a 
 +[   11.197620] ip_tables: (C) 2000-2006 Netfilter Core Team 
 +[   11.213074] nf_conntrack version 0.5.0 (1024 buckets, 4096 max) 
 +[   11.279550] usbcore: registered new interface driver usbserial 
 +[   11.285562] usbcore: registered new interface driver usbserial_generic 
 +[   11.292348] usbserial: USB Serial support registered for generic 
 +[   11.319247] xt_time: kernel timezone is -0000 
 +[   11.387933] mt76_wmac 10300000.wmac: ASIC revision: 76280001 
 +[   12.409366] mt76_wmac 10300000.wmac: Firmware Version: 20151201 
 +[   12.415386] mt76_wmac 10300000.wmac: Build Time: 20151201183641 
 +[   12.437322] mt76_wmac 10300000.wmac: firmware init done 
 +[   12.644251] PPP generic driver version 2.4.2 
 +[   12.656128] NET: Registered protocol family 24 
 +[   12.726175] qmi_wwan 1-1:1.4: cdc-wdm0: USB WDM device 
 +[   12.738618] qmi_wwan 1-1:1.4 wwan0: register 'qmi_wwan' at usb-101c0000.ehci-1, WWAN/QMI device, 56:cc:a8:b3:d3:2e 
 +[   12.749534] usbcore: registered new interface driver qmi_wwan 
 +[   12.788462] mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4 
 +[   12.794904] mt76x0e 0000:01:00.0: ASIC revision: 76100002 
 +[   12.977943] mt76x0e 0000:01:00.0: Firmware Version: 0.1.00 
 +[   13.229437] mt76x0e 0000:01:00.0: EEPROM ver:02 fae:00 
 +[   13.259231] usbcore: registered new interface driver option 
 +[   13.264966] usbserial: USB Serial support registered for GSM modem (1-port) 
 +[   13.290912] kmodloader: done loading kernel modules from /etc/modules.d/
 +[   14.050623] urandom_read: 5 callbacks suppressed 
 +[   14.050633] random: jshn: uninitialized urandom read (4 bytes read) 
 +[   17.964494] rt3050-esw 10110000.esw: link changed 0x00 
 +[   21.547572] rt3050-esw 10110000.esw: link changed 0x04 
 +[   24.287024] br-lan: port 1(eth0.1) entered blocking state 
 +[   24.292586] br-lan: port 1(eth0.1) entered disabled state 
 +[   24.298438] device eth0.1 entered promiscuous mode 
 +[   24.303303] device eth0 entered promiscuous mode 
 +[   24.346500] br-lan: port 1(eth0.1) entered blocking state 
 +[   24.352055] br-lan: port 1(eth0.1) entered forwarding state 
 +[   24.357936] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready 
 +[   25.238016] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready 
 +</nowiki>
 </WRAP>\\ </WRAP>\\
  
Line 191: Line 1235:
  
 [[meta:tags|How to add tags]] [[meta:tags|How to add tags]]
-{{tag>MT7628 8flash 64ram}}+{{tag>MT7628 MT7610 MDM9207 8flash 64ram MR200v4}} 
  • Last modified: 2021/01/13 05:13
  • by mctifa