TP-Link Deco X60 2

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

TP-Link Deco X60 is a dual-band AX5400 Mesh WiFi 6 router. Version 2 runs on Qualcomm IPQ8071 SoC with QCN5024/QCN5054 wireless chips.

Coming up

Pull request for support https://github.com/openwrt/openwrt/pull/24052

OpenWrt forum thread: https://forum.openwrt.org/t/adding-support-for-tp-link-deco-x60-v2-eu/251502

CPU	Ram	Flash	Network	WLAN	USB	Serial	JTag
EXAMPLE RT3052 @ 384 MHz	64 MiB	8 MiB	4x 10/100	bgn	1x 2.0	Yes	?

Architecture	EXAMPLE MIPS
Vendor	EXAMPLE Ralink
Bootloader	EXAMPLE U-Boot
System-On-Chip	EXAMPLE Ralink RT3052 - MIPS 24K V4.12
CPU/Speed	EXAMPLE 451 MHz
Flash-Chip	EXAMPLE unkown
Flash size	EXAMPLE 8 MiB
RAM	EXAMPLE 64 MiB
Wireless	EXAMPLE RT2860v2 2.4GHz 802.11bgn
Ethernet	EXAMPLE 10/100 Mbit/s w/ vlan support
Switch	EXAMPLE Qualcomm Atheros QCA8337
USB	EXAMPLE 1x 2.0
Serial	EXAMPLE Yes
JTAG	EXAMPLE Not populated

Base of the casing

Top of the casing

Underside of top

Internal unit

Inside casing

The case is opened by popping the lid. There are four tabs that need to be pushed inwards. I found using a wide flathead screwdriver works well. Usually this breaks the tips of the clips, but hot glue is your friend.
After the lid is removed, there are two screws holding the internal unit in place. Removing the screws will release it and you can slide it out of the case.
Unplug antennas.
The board is held in the plastic frame by another two screws, remove these and slightly tilt to free from plastic holders.

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

The board has pads for serial.
Image left to right: TP8=VCC, TP7=GND, TP6=RX and TP5=TX.

Serial connection parameters for TP-Link Deco X60 2	115200, 8N1, 1.8V

Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00156 S - IMAGE_VARIANT_STRING=HAACANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x000002e5 B - 201 - PBL, Start B - 2735 - bootable_media_detect_entry, Start B - 3442 - bootable_media_detect_success, Start B - 3446 - elf_loader_entry, Start B - 6107 - auth_hash_seg_entry, Start B - 6350 - auth_hash_seg_exit, Start B - 68230 - elf_segs_hash_verify_entry, Start B - 131054 - PBL, End B - 145424 - SBL1, Start B - 198402 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4 B - 204990 - pm_device_init, Start B - 328241 - PM_SET_VAL:Skip D - 122732 - pm_device_init, Delta B - 330650 - pm_driver_init, Start D - 5337 - pm_driver_init, Delta B - 336994 - clock_init, Start D - 2135 - clock_init, Delta B - 341051 - boot_flash_init, Start D - 13206 - boot_flash_init, Delta B - 357917 - boot_config_data_table_init, Start D - 3202 - boot_config_data_table_init, Delta - (575 Bytes) B - 365451 - Boot Setting : 0x00000600 B - 369385 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:16 B - 376309 - sbl1_ddr_set_params, Start B - 380152 - CPR configuration: 0x300 B - 383537 - cpr_init, Start B - 386404 - Rail:0 Mode: 5 Voltage: 800000 B - 391559 - CL CPR settled at 752000mV B - 394395 - Rail:1 Mode: 5 Voltage: 880000 B - 398574 - Rail:1 Mode: 7 Voltage: 888000 D - 16470 - cpr_init, Delta B - 405467 - Pre_DDR_clock_init, Start B - 409493 - Pre_DDR_clock_init, End B - 412878 - DDR Type : PCDDR3 B - 418490 - do ddr sanity test, Start D - 1037 - do ddr sanity test, Delta B - 423340 - DDR: Start of HAL DDR Boot Training B - 428067 - DDR: End of HAL DDR Boot Training B - 433740 - DDR: Checksum to be stored on flash is 1770463305 B - 444080 - Image Load, Start D - 224114 - QSEE Image Loaded, Delta - (1374392 Bytes) B - 668285 - Image Load, Start D - 61 - SEC Image Loaded, Delta - (0 Bytes) B - 675941 - Image Load, Start D - 10705 - DEVCFG Image Loaded, Delta - (26008 Bytes) B - 686738 - Image Load, Start D - 25284 - RPM Image Loaded, Delta - (106428 Bytes) B - 712114 - Image Load, Start D - 109098 - APPSBL Image Loaded, Delta - (672308 Bytes) B - 821334 - QSEE Execution, Start D - 61 - QSEE Execution, Delta B - 827160 - USB D+ check, Start D - 0 - USB D+ check, Delta B - 833534 - SBL1, End D - 690428 - SBL1, Delta S - Flash Throughput, 6755 KB/s (2180383 Bytes, 322774 us) S - DDR Frequency, 466 MHz S - Core 0 Frequency, 800 MHz U-Boot 2016.01 (May 11 2020 - 18:03:48 -0700) DRAM: smem ram ptable found: ver: 1 len: 4 512 MiB NAND: ONFI device found ID = 9500a1ef Vendor = ef Device = a1 128 MiB MMC: sdhci: Node Not found, skipping initialization PCI1 is not defined in the device tree In: serial@78B3000 Out: serial@78B3000 Err: serial@78B3000 machid: 8010010 MMC Device 0 not found eth0 MAC Address from ART is not valid eth1 MAC Address from ART is not valid eth2 MAC Address from ART is not valid eth3 MAC Address from ART is not valid eth4 MAC Address from ART is not valid eth5 MAC Address from ART is not valid ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=0", size 9 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 72, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 9/4, WL threshold: 4096, image sequence number: 1864824124 ubi0: available PEBs: 0, total reserved PEBs: 72, PEBs reserved for bad PEB handling: 20 Find no boot alter flag! Enter magic string to stop autoboot in 1 seconds Unmounting UBIFS volume ubi_factory_data! ubi0: detaching mtd1 ubi0: mtd1 is detached ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=0", size 42 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 336, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1272319753 ubi0: available PEBs: 120, total reserved PEBs: 216, PEBs reserved for bad PEB handling: 20 Read 0 bytes from volume kernel to 44000000 No size specified -> Using max size (5459968) ## Loading kernel from FIT Image at 44000000 ... Using 'config@ac04' configuration Trying 'kernel@1' kernel subimage Description: ARM64 OpenWrt Linux-4.4.60 Type: Kernel Image Compression: gzip compressed Data Start: 0x440000e8 Data Size: 3825445 Bytes = 3.6 MiB Architecture: AArch64 OS: Linux Load Address: 0x41080000 Entry Point: 0x41080000 Hash algo: crc32 Hash value: 9d1e8fbe Hash algo: sha1 Hash value: 83857dbd19331556dd6a0372ffdde6f2821f27f9 Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 44000000 ... Using 'config@ac04' configuration Trying 'fdt@ac04' fdt subimage Description: ARM64 OpenWrt qcom-ipq807x-hkxx device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x443f755c Data Size: 79818 Bytes = 77.9 KiB Architecture: AArch64 Hash algo: crc32 Hash value: 192ae3b2 Hash algo: sha1 Hash value: 0722dfed70e08c9953ce0a7ab4d742da7467b9ae Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x443f755c Uncompressing Kernel Image ... OK Loading Device Tree to 4a3e9000, end 4a3ff7c9 ... OK Could not find PCI in device tree Using machid 0x8010010 from environment Starting kernel ... Jumping to AARCH64 kernel via monitor [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 4.4.60 (user@4d3b5617687d) (gcc version 5.2.0 (OpenWrt GCC 5.2.0 5a99dbf88+r49254) ) #1 SMP PREEMPT Fri Sep 12 14:50:08 CST 2025 [ 0.000000] Boot CPU: AArch64 Processor [410fd034] [ 0.000000] Ignoring memory range 0x40000000 - 0x41000000 [ 0.000000] efi: Getting EFI parameters from FDT: [ 0.000000] efi: UEFI not found. [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] PERCPU: Embedded 14 pages/cpu @ffffffc01ef5d000 s19072 r8192 d30080 u57344 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] CPU features: enabling workaround for ARM erratum 845719 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 107856 [ 0.000000] Kernel command line: ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait swiotlb=1 coherent_pool=2M [ 0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) [ 0.000000] software IO TLB [mem 0x5fe58000-0x5fe98000] (0MB) mapped at [ffffffc01ee58000-ffffffc01ee97fff] [ 0.000000] Memory: 411264K/438272K available (5222K kernel code, 606K rwdata, 2252K rodata, 224K init, 399K bss, 27008K reserved, 0K cma-reserved) [ 0.000000] Virtual kernel memory layout: [ 0.000000] vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000 ( 246 GB) [ 0.000000] vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000 ( 8 GB maximum) [ 0.000000] 0xffffffbdc0040000 - 0xffffffbdc0800000 ( 7 MB actual) [ 0.000000] fixed : 0xffffffbffa7fd000 - 0xffffffbffac00000 ( 4108 KB) [ 0.000000] PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000 ( 16 MB) [ 0.000000] modules : 0xffffffbffc000000 - 0xffffffc000000000 ( 64 MB) [ 0.000000] memory : 0xffffffc000000000 - 0xffffffc01f000000 ( 496 MB) [ 0.000000] .init : 0xffffffc0007cf000 - 0xffffffc000807000 ( 224 KB) [ 0.000000] .text : 0xffffffc000080000 - 0xffffffc0007ce874 ( 7483 KB) [ 0.000000] .data : 0xffffffc000816000 - 0xffffffc0008ada00 ( 607 KB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] Preemptible hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 64. [ 0.000000] NR_IRQS:64 nr_irqs:64 0 [ 0.000000] Architected cp15 timer(s) running at 19.20MHz (virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000005] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.000423] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000) [ 0.000434] pid_max: default: 32768 minimum: 301 [ 0.000523] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes) [ 0.000533] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes) [ 0.001196] EFI services will not be available. [ 0.001221] ASID allocator initialised with 65536 entries [ 0.051788] MSM Memory Dump base table set up [ 0.051810] MSM Memory Dump apps data table set up [ 0.090105] Detected VIPT I-cache on CPU1 [ 0.090149] CPU1: Booted secondary processor [410fd034] [ 0.120091] Detected VIPT I-cache on CPU2 [ 0.120120] CPU2: Booted secondary processor [410fd034] [ 0.150116] Detected VIPT I-cache on CPU3 [ 0.150143] CPU3: Booted secondary processor [410fd034] [ 0.150192] Brought up 4 CPUs [ 0.150217] SMP: Total of 4 processors activated. [ 0.150227] CPU: All CPU(s) started at EL1 [ 0.150249] alternatives: patching kernel code [ 0.166068] DMI not present or invalid. [ 0.166303] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.166328] futex hash table entries: 1024 (order: 5, 131072 bytes) [ 0.166507] pinctrl core: initialized pinctrl subsystem [ 0.167631] NET: Registered protocol family 16 [ 0.190042] cpuidle: using governor ladder [ 0.220058] cpuidle: using governor menu [ 0.220218] vdso: 2 pages (1 code @ ffffffc00081d000, 1 data @ ffffffc00081c000) [ 0.221120] DMA: preallocated 2048 KiB pool for atomic allocations [ 0.221257] CPU: IPQ8071A, SoC Version: 2.0 [ 0.221292] <CORE> glink_init: IPC Logging Disabled [ 0.221748] IPC logging disabled [ 0.221754] IPC logging disabled [ 0.221759] IPC logging disabled [ 0.221763] IPC logging disabled [ 0.221768] IPC logging disabled [ 0.224542] Soc version is not 1, changing clock offsets [ 0.233042] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ! [ 0.235281] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ! [ 0.237551] msm_rpm_dev_probe: APSS-RPM communication over GLINK [ 0.238473] sps:sps is ready. [ 0.282063] pps_core: LinuxPPS API ver. 1 registered [ 0.282070] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.282094] PTP clock support registered [ 0.282253] dmi: Firmware registration failed. [ 0.283306] Advanced Linux Sound Architecture Driver Initialized. [ 0.283943] clocksource: Switched to clocksource arch_sys_counter [ 0.286995] NET: Registered protocol family 2 [ 0.287549] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 0.287610] TCP bind hash table entries: 4096 (order: 4, 65536 bytes) [ 0.287707] TCP: Hash tables configured (established 4096 bind 4096) [ 0.287756] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.287779] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.287946] NET: Registered protocol family 1 [ 0.295166] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.295183] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.298504] Key type asymmetric registered [ 0.298520] Asymmetric key parser 'x509' registered [ 0.298552] io scheduler noop registered [ 0.298566] io scheduler deadline registered (default) [ 0.300495] 20000000.pci supply vdda not found, using dummy regulator [ 0.300546] 20000000.pci supply vdda_phy not found, using dummy regulator [ 0.300580] 20000000.pci supply vdda_refclk not found, using dummy regulator [ 0.301129] PCI host bridge /soc/pci@20000000 ranges: [ 0.301156] IO 0x20200000..0x2020ffff -> 0x20200000 [ 0.301171] MEM 0x20220000..0x2fffffff -> 0x20220000 [ 1.455597] qcom-pcie 20000000.pci: phy link never came up [ 1.457156] qcom-pcie 20000000.pci: hostinit failed [ 1.457166] qcom-pcie 20000000.pci: cannot initialize host [ 1.457316] qcom-pcie: probe of 20000000.pci failed with error -110 [ 1.462527] NET: Registered protocol family 27 [ 1.462539] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled [ 1.462555] qmi_log_init: IPC Logging disabled [ 1.462561] qmi_log_init: IPC Logging disabled [ 1.462654] msm_rpm_log_probe: OK [ 1.462957] msm-dcc b3000.dcc: DCC XPU is not specified [ 1.463206] msm-dcc b3000.dcc: jiffies_64: 0xffff8b61, cntvct_64: 0x6904e59 [ 1.463218] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xffffff800027e004) [ 1.463229] msm-dcc b3000.dcc: gcnt_lo: 0x0690502d(0xffffff800027e000) [ 1.463770] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set [ 1.464509] msm_serial 78b3000.serial: msm_serial: detected port #0 [ 1.464548] msm_serial 78b3000.serial: uartclk = 3686400 [ 1.464584] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 77, base_baud = 230400) is a MSM [ 1.464603] msm_serial: console setup on port #0 [ 2.160339] console [ttyMSM0] enabled [ 2.165292] msm_serial: driver initialized [ 2.168825] msm_serial_hsl_init: driver initialized [ 2.180955] brd: module loaded [ 2.182000] flash_chrdev : flash_chrdev_init [ 2.182895] flash_chrdev : flash_chrdev_init [ 2.188446] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xa1 [ 2.191668] nand: ONFI 10-Compliant Winbond W29N01HZ [ 2.198131] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.203121] 17 ofpart partitions found on MTD device qcom_nand.0 [ 2.210459] Creating 17 MTD partitions on "qcom_nand.0": [ 2.216594] 0x000000000000-0x000000100000 : "0:SBL1" [ 2.223388] 0x000000100000-0x000000200000 : "0:MIBIB" [ 2.228281] 0x000000200000-0x000000280000 : "0:BOOTCONFIG" [ 2.232780] 0x000000280000-0x000000300000 : "0:BOOTCONFIG1" [ 2.238243] 0x000000300000-0x000000600000 : "0:QSEE" [ 2.245715] 0x000000600000-0x000000680000 : "0:DEVCFG" [ 2.248839] 0x000000680000-0x000000700000 : "0:APDP" [ 2.253780] 0x000000700000-0x000000780000 : "0:RPM" [ 2.258926] 0x000000780000-0x000000800000 : "0:CDT" [ 2.263508] 0x000000800000-0x000000980000 : "0:APPSBLENV" [ 2.269222] 0x000000980000-0x000000b80000 : "0:APPSBL" [ 2.275159] 0x000000b80000-0x000000c00000 : "0:ART" [ 2.278965] 0x000000c00000-0x000003600000 : "rootfs" [ 2.318327] mtd: device 12 (rootfs) set to be root filesystem [ 2.318628] mtdsplit: no squashfs found in "rootfs" [ 2.323049] 0x000003600000-0x000006000000 : "rootfs_1" [ 2.363402] 0x000006000000-0x000006080000 : "0:ETHPHYFW" [ 2.364448] 0x000006080000-0x000006980000 : "factory_data" [ 2.375838] 0x000006980000-0x000007a80000 : "runtime_data" [ 2.391135] libphy: Fixed MDIO Bus: probed [ 2.611845] qca-mdio 90000.mdio: Could not find phy-reset-gpio [ 2.611968] libphy: qca_mdio: probed [ 2.617727] qca-mdio 90000.mdio: qca-mdio driver was registered [ 2.620473] Unable to create IPC log context! [ 2.626255] cnss: Platform driver probed successfully. [ 2.630661] Skip QCA8074V1 in V2 platform [ 2.635619] cnss_genl: genl_register_family fail: -17 [ 2.639562] cnss: CNSS genl init failed -17 [ 2.644638] cnss: Platform driver probed successfully. [ 2.648714] i2c /dev entries driver [ 2.661485] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz [ 2.661575] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1017600 KHz [ 2.667796] sdhci: Secure Digital Host Controller Interface driver [ 2.676297] sdhci: Copyright(c) Pierre Ossman [ 2.682353] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.687994] [ 2.687994] Version Rollback Feature Disabled [ 2.692940] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000008b04000 [ 2.698175] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000008b04000 [ 2.715436] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000008b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000008b04000 [ 2.731322] sps:BAM 0x0000000008b04000 is registered.[ 2.738985] DEV CI test message [ 2.743701] subsys-restart: ssr_parse_restart_orders(): q6v5_m3 device has been added to q6v5-m3's restart group [ 2.746531] subsys-restart: ssr_parse_restart_orders(): q6v5_wcss device has been added to q6v5-m3's restart group [ 2.756993] remoteproc remoteproc0: q6v5-m3 is available [ 2.767439] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000 [ 2.772604] coresight-csr 6001000.csr: CSR initialized [ 2.780045] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000 [ 2.785000] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000 [ 2.792536] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000 [ 2.799924] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000 [ 2.807305] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000 [ 2.814680] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000 [ 2.822046] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000 [ 2.829447] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000 [ 2.836820] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000 [ 2.844199] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000 [ 2.851563] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000 [ 2.858954] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000 [ 2.866335] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000 [ 2.873704] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000 [ 2.881090] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000 [ 2.888465] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000 [ 2.895850] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000 [ 2.903363] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000 [ 2.910702] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000 [ 2.918108] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000 [ 2.925516] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000 [ 2.932880] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000006044000 [ 2.940010] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000006044000 [ 2.957103] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000006044000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000006044000 [ 2.972980] sps:BAM 0x0000000006044000 is registered.[ 2.980572] coresight-tmc 6028000.tmc: TMC initialized [ 2.985350] coresight-tmc 6027000.tmc: TMC initialized [ 2.990504] coresight-funnel 6021000.funnel: FUNNEL initialized [ 2.995563] coresight-funnel 6100000.funnel: FUNNEL initialized [ 3.001357] coresight-funnel 6120000.funnel: FUNNEL initialized [ 3.007282] coresight-funnel 6130000.funnel: FUNNEL initialized [ 3.013170] coresight-funnel 61a1000.funnel: FUNNEL initialized [ 3.019536] coresight-etm4x 619c000.etm: ETM 4.0 initialized [ 3.025242] coresight-etm4x 619d000.etm: ETM 4.0 initialized [ 3.031159] coresight-etm4x 619e000.etm: ETM 4.0 initialized [ 3.036840] coresight-etm4x 619f000.etm: ETM 4.0 initialized [ 3.042188] coresight-replicator-qcom 6026000.replicator: REPLICATOR 1.0 initialized [ 3.047946] coresight-stm 6002000.stm: STM initialized [ 3.056279] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000 [ 3.060384] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized [ 3.070120] Netfilter messages via NETLINK v0.30. [ 3.075794] ip_tables: (C) 2000-2006 Netfilter Core Team [ 3.080538] NET: Registered protocol family 10 [ 3.086238] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 3.089905] NET: Registered protocol family 17 [ 3.095330] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 3.099661] Bridge firewalling registered [ 3.112396] 8021q: 802.1Q VLAN Support v1.8 [ 3.117600] <CORE> glink_core_register_transport: IPC Logging disabled [ 3.120339] msm_glink_smem_native_xprt rx fifo not found [ 3.127282] DEV CI test message [ 3.132805] remoteproc remoteproc1: q6v5-wcss is available [ 3.135485] ubi0: attaching mtd12 [ 3.349583] ubi0: scanning is finished [ 3.356177] ubi0: attached mtd12 (name "rootfs", size 42 MiB) [ 3.356200] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.360894] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.367677] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.374530] ubi0: good PEBs: 336, bad PEBs: 0, corrupted PEBs: 0 [ 3.381291] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 3.387553] ubi0: max/mean erase counter: 3/2, WL threshold: 4096, image sequence number: 1272319753 [ 3.394587] ubi0: available PEBs: 120, total reserved PEBs: 216, PEBs reserved for bad PEB handling: 20 [ 3.403879] ubi0: background thread "ubi_bgt0d" started, PID 117 [ 3.414386] input: soc:gpio_keys as /devices/platform/soc/soc:gpio_keys/input/input0 [ 3.419288] hctosys: unable to open rtc device (rtc0) [ 3.435465] ALSA device list: [ 3.435487] No soundcards found. [ 3.439966] VFS: Mounted root (squashfs filesystem) readonly on device 31:18. [ 3.440881] Freeing unused kernel memory: 224K (ffffffc0007cf000 - ffffffc000807000) [ 3.447988] Freeing alternatives memory: 40K (ffffffc000807000 - ffffffc000811000) [ 3.842647] init: Console is alive [ 3.842782] init: - watchdog - [ 3.889758] random: nonblocking pool is initialized [ 5.030940] usbcore: registered new interface driver usbfs [ 5.031004] usbcore: registered new interface driver hub [ 5.035458] usbcore: registered new device driver usb [ 5.041351] Button Hotplug driver version 0.4.1 [ 5.845460] init: - preinit - ignore preinit load_wifi_board_bin Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level Before mount_root mounting /dev/root cp: can't stat '/tmp/log_export_tmp/*': No such file or directory After mount_root [ 9.487004] procd: - early - [ 9.487474] procd: - watchdog - [ 10.135387] procd: - ubus - [ 11.137103] procd: - init - Please press Enter to activate this console. [ 11.220743] ubi1: attaching mtd15 [ 11.265489] ubi1: scanning is finished [ 11.271824] ubi1: attached mtd15 (name "factory_data", size 9 MiB) [ 11.271847] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 11.276901] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 11.283746] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 11.290616] ubi1: good PEBs: 72, bad PEBs: 0, corrupted PEBs: 0 [ 11.297381] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 11.303279] ubi1: max/mean erase counter: 9/4, WL threshold: 4096, image sequence number: 1864824124 [ 11.310583] ubi1: available PEBs: 0, total reserved PEBs: 72, PEBs reserved for bad PEB handling: 20 [ 11.319881] ubi1: background thread "ubi_bgt1d" started, PID 211 ubi_factory_data found, mounting... [ 11.361099] UBIFS (ubi1:0): background thread "ubifs_bgt1_0" started, PID 218 [ 11.394750] UBIFS (ubi1:0): recovery needed [ 11.476626] UBIFS (ubi1:0): recovery completed [ 11.476698] UBIFS (ubi1:0): UBIFS: mounted UBI device 1, volume 0, name "ubi_factory_data" [ 11.479971] UBIFS (ubi1:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 11.488232] UBIFS (ubi1:0): FS size: 4825088 bytes (4 MiB, 38 LEBs), journal size 1142785 bytes (1 MiB, 9 LEBs) [ 11.498209] UBIFS (ubi1:0): reserved for root: 0 bytes (0 KiB) [ 11.508091] UBIFS (ubi1:0): media format: w4/r0 (latest is w4/r0), UUID D7447E3F-6F68-4E39-B5DF-9EE92604DC7F, small LPT model [ 11.523332] ubi2: attaching mtd16 [ 11.609796] ubi2: scanning is finished [ 11.616405] ubi2: attached mtd16 (name "runtime_data", size 17 MiB) [ 11.616429] ubi2: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 11.621469] ubi2: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 11.628427] ubi2: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 11.635280] ubi2: good PEBs: 136, bad PEBs: 0, corrupted PEBs: 0 [ 11.642041] ubi2: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 11.648302] ubi2: max/mean erase counter: 16/9, WL threshold: 4096, image sequence number: 1626932842 [ 11.655336] ubi2: available PEBs: 0, total reserved PEBs: 136, PEBs reserved for bad PEB handling: 20 [ 11.664638] ubi2: background thread "ubi_bgt2d" started, PID 224 [ 11.677892] UBIFS (ubi2:0): background thread "ubifs_bgt2_0" started, PID 231 ubi_runtime_data found, mounting... [ 11.713603] UBIFS (ubi2:0): recovery needed [ 11.827938] UBIFS (ubi2:0): recovery completed [ 11.828014] UBIFS (ubi2:0): UBIFS: mounted UBI device 2, volume 0, name "ubi_runtime_data" [ 11.831272] UBIFS (ubi2:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 11.839537] UBIFS (ubi2:0): FS size: 9904128 bytes (9 MiB, 78 LEBs), journal size 1777664 bytes (1 MiB, 14 LEBs) [ 11.849514] UBIFS (ubi2:0): reserved for root: 0 bytes (0 KiB) [ 11.859751] UBIFS (ubi2:0): media format: w4/r0 (latest is w4/r0), UUID 9796B8EA-F494-4085-9A40-ECE182394428, small LPT model WIFI FW mount is successful [ 12.823540] cfg80211: World regulatory domain updated: [ 12.823568] cfg80211: DFS Master region: unset [ 12.827648] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time) [ 12.832225] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A) [ 12.841758] cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz, 92000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 12.849569] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A) [ 12.858944] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (N/A) [ 12.866980] cfg80211: (5250000 KHz - 5330000 KHz @ 80000 KHz, 160000 KHz AUTO), (N/A, 2000 mBm), (0 s) [ 12.874332] ssdk_switch_device_num_init[998]:INFO:ess-switch dts node number: 1 [ 12.874387] ssdk_dt_get_switch_node[836]:INFO:ess-switch DT exist! [ 12.874397] ssdk_dt_parse_access_mode[737]:INFO:switch_access_mode: local bus [ 12.874401] ssdk_dt_parse_access_mode[750]:INFO:switchreg_base_addr: 0x3a000000 [ 12.874404] ssdk_dt_parse_access_mode[751]:INFO:switchreg_size: 0x1000000 [ 12.874409] ssdk_dt_parse_mac_mode[242]:INFO:mac mode = 0x0 [ 12.874414] ssdk_dt_parse_mac_mode[251]:INFO:mac mode1 = 0xff [ 12.874418] ssdk_dt_parse_mac_mode[260]:INFO:mac mode2 = 0xff [ 12.874453] ssdk_dt_parse_uniphy[279]:INFO:ess-uniphy DT exist! [ 12.874791] ssdk_plat_init start [ 12.943370] cfg80211: (5490000 KHz - 5730000 KHz @ 160000 KHz), (N/A, 2000 mBm), (0 s) [ 12.946858] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A) [ 12.954929] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A) [ 12.956364] ssdk_ppe_clock_init[517]:INFO:ppe and uniphy clock init successfully! [ 12.971493] HPPE initializing... [ 12.978539] malibu_phy_api_ops_init[2860]:INFO:qca probe malibu phy driver succeeded! [ 12.989530] regi_init[3365]:INFO:Initializing HPPE!! [ 13.203952] ssdk_ppe_reset_init[798]:INFO:ppe reset successfully! [ 13.210284] qca_hppe_tdm_hw_init[737]:INFO:tdm setup num=96 [ 13.213565] qca_hppe_portctrl_hw_init[165]:INFO:Hawkeye PPE port initializing [ 13.430076] ssdk_switch_register[1618]:INFO:Chip version 0x1500 [ 13.433058] qca_link_polling_select[1280]:INFO:link-polling-required node does not exist [ 13.439298] ssdk_switch_register[1643]:INFO:polling is selected [ 13.447029] regi_init[3369]:INFO:Initializing HPPE Done!! [ 13.451942] regi_init[3423]:INFO:qca-ssdk module init succeeded! [ 13.458915] tun: Universal TUN/TAP device driver, 1.6 [ 13.460395] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 13.468092] EDMA ver 1 hw init [ 13.471638] EDMA HW Reset completed succesfully [ 13.474517] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7) [ 13.478885] RxDesc:1 (15-15) RxFill:1 (7-7) [ 13.484646] GMAC5(ffffffc01b0d2880) Invalid MAC@ - using 2a:64:22:7e:1b:9d [ 13.489259] GMAC4(ffffffc01b0d7880) Invalid MAC@ - using c6:c0:08:f4:63:3c [ 13.496317] ********************************************************** [ 13.502065] * NSS Data Plane driver [ 13.508682] ********************************************************** [ 13.515388] l2tp_core: L2TP core driver, V2.0 [ 13.519136] l2tp_netlink: L2TP netlink interface [ 13.743903] nss_driver - fw of size 688808 bytes copied to load addr: 40000000, nss_id : 0 [ 13.745916] Supported Frequencies - [ 13.751052] 187.2 MHz 748.8 MHz [ 13.757034] 1.4976 GHz [ 13.757992] [ 13.760469] ffffffbffc31ae00: meminfo init succeed [ 13.798692] node size 2 # items 4 [ 13.798720] memory: 40000000 536870912 (avl 448163840) items 4 active_cores 2 [ 13.801046] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000 [ 13.808115] ffffffbffc31ae00: nss core 0 booted successfully [ 13.816243] nss_driver - fw of size 287960 bytes copied to load addr: 40800000, nss_id : 1 [ 13.821776] Supported Frequencies - [ 13.828789] 187.2 MHz 748.8 MHz [ 13.834753] 1.4976 GHz [ 13.835697] [ 13.838192] ffffffbffc322080: meminfo init succeed [ 13.841458] sit: IPv6 over IPv4 tunneling driver [ 13.843968] node size 2 # items 4 [ 13.843974] memory: 40000000 536870912 (avl 448278528) items 4 active_cores 2 [ 13.844018] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000 [ 13.844030] ffffffbffc322080: nss core 1 booted successfully [ 13.867760] nat46: module (version 8ff2ae59ec9840a7b8b45f976c51cae80abe0226) loaded. [ 13.875327] tipc: Activated (version 2.0.0) [ 13.879606] NET: Registered protocol family 30 [ 13.883630] tipc: Started in single node mode [ 13.888612] gre: GRE over IPv4 demultiplexor driver [ 13.893245] ip_gre: GRE over IPv4 tunneling driver [ 13.898972] ip6_gre: GRE over IPv6 tunneling driver [ 13.904728] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 13.909616] QCA multicast snooping installed successfully [ 13.918184] QCA Hy-Fi multicast installation successfully [ 13.923889] PPP generic driver version 2.4.2 [ 13.925819] nss_lag_init[354]:LAG Manager Installed [ 13.929940] NET: Registered protocol family 24 [ 13.935563] PPTP driver version 0.8.5 [ 13.941752] diag: IPC Logging disabled [ 13.976257] <NSS-CRYPTO>:module loaded Build_ID - 09/12/25, 14:40:49 SoC=ipq807x_64 [ 13.978459] cannot find nss-macsec0 node [ 13.982880] cannot find nss-macsec1 node [ 13.987175] cannot find nss-macsec2 node [ 13.990786] nss_macsec init success [ 14.005633] u32 classifier [ 14.005653] Performance counters on [ 14.007223] input device check on [ 14.010956] Actions configured [ 14.015837] Mirror/redirect action on [ 14.023139] nf_conntrack version 0.5.0 (3215 buckets, 12860 max) [ 14.032962] safesearch_dns: module license 'unspecified' taints kernel. [ 14.032993] Disabling lock debugging due to kernel taint [ 14.056933] device recognition register succes [ 14.062847] Ebtables v2.0 registered [ 14.065850] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 14.148268] ctnetlink v0.93: registering with nfnetlink. [ 14.298242] xt_time: kernel timezone is -0000 reloadprofile() begin reloadprofile() end ==reloadConfig()== begin ==loadDefaultConfig()== begin ==loadConfigToFiles(): default-config to /tmp/defaultconfig== begin ==loadConfigToFiles()== end ==set_usrconfig_info()== start ==set_usrconfig_info()== end ==loadDefaultConfig()== end ==loadConfigToFiles(): user-config to /tmp/userconfig== begin ==loadConfigToFiles()== end ==reloadConfig()===== no need to load emmc-config ==loadConfigToFiles(): device-config to /tmp/userconfig== begin ==loadConfigToFiles()== end ** user-config loaded ** === update_config ==reloadConfig()== end merge_extra_config() begin ==loadConfigToFiles(): default-config to /tmp/merge== begin ==loadConfigToFiles()== end mergeconfigbycountry() begin mergeconfigbycountry() country DE mergeconfigbycountry() end merge_extra_config() end phylink down boot 1 [ 16.636533] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 16.655967] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 16.676675] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready [ 18.360275] Load statistics in AP Mode [ 18.360392] module inited to down eth0/1 after netfid [ 18.896965] IPv6: ADDRCONF(NETDEV_UP): br-wan: link is not ready [ 18.908037] device eth0 entered promiscuous mode [ 18.908352] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready [ 18.916290] device eth1 entered promiscuous mode [awnd_init:4941]: plc backhaul can not be enable without plc_attached [awnd_init:4943]: backhaul_option:1 [awnd_init:4954]: wifi backhaul is enable whc (repacd): stop repacd-run.sh apsd: start apsd whc (repacd): Start: whc (repacd): GatewayConnectedMode(gwcon_mode): RE mac:40-3F-8C-79-57-9C role:RE mac:40-3F-8C-79-57-90 role:AP whc (repacd): TrafficSeparationEnabled(traffic_separation_enabled): 1 fap: 40:3F:8C:79:57:90 whc (repacd): get whc_wifi_config_lock whc (repacd): starting WHC auto-configuration whc (repacd): Managed network: lan whc (repacd): Device type: RE whc (repacd): Sysmode: AP whc (repacd): the guest network version of the device is latest, we do nothing(uci_revert_state wifi guest enable) =========Fix default enable ========= whc (repacd): Start: whc (repacd): GatewayConnectedMode(gwcon_mode): RE whc (repacd): TrafficSeparationEnabled(traffic_separation_enabled): 1 notify app-dpi than LAN IP change [ 19.723155] mode:1 [ 19.723177] dlogin_bridge_hook_ops whc (repacd): wifi config change(is different from /var/state/wifi). wifi_cmd:reload wifi1,wifi0 whc (repacd): Using SON mode for NonCAP whc (repacd): __repacd_restart_dependencies: Restarting network stack... wifi reload starting recovery daemon acfg_tool: Issuing blocking call to wait for events starting recovery daemon acfg_tool: Issuing blocking call to wait for events qcawifi qcawificfg80211 disable radio wifi1 qcawifi qcawificfg80211 disable radio wifi0 qcawifi qcawificfg80211 disable radio wifi2 starting recovery daemon acfg_tool: Issuing blocking call to wait for events starting recovery daemon acfg_tool: Issuing blocking call to wait for events qcawifi qcawificfg80211: enable radio wifi1 update_ini_file cfg80211_config=1 update_ini_file qwrap_enable=0 update_ini_file nss_wifi_olcfg=3 update_ini_file rx_hash=0 [ 23.620276] configuring additional NSS pbufs [ 23.632007] additional pbufs of size 3100672 got added to NSS update_ini_file allow_mon_vaps_in_sr= [ 23.701357] qdf_dbg_mask value is invalid [ 23.701384] Using the default module debug levels instead [ 23.704500] qdf_print_ctrl_register: Allocated print control object 0 [ 23.709940] MINIDUMP VA .bss start=ffffffbffc7ef700 module=qdf [ 24.264896] wlan: [2895:E:CONFIG] cfg_uint_item_handler: 142: allow_mon_vaps_in_sr= - Invalid format (status 16); Using default 0 [ 24.264995] wlan: [2895:E:CONFIG] cfg_uint_item_handler: 171: gScanProbeRepeatTime=50 - Out of range [0, 30]; Using 50 [ 24.275843] MINIDUMP VA .bss start=ffffffbffca97b80 module=umac===parental_control_avira=== no need to start *****starting cnssdaemon***** *********initiating cold boot calibration************* === ip addr del 192.168.0.1 dev br-lan start === ip addr del 192.168.0.1 dev br-lan end [ 24.603160] [ 24.603160] MINIDUMP VA .bss start=ffffffbffcd99b00 module=qca_ol*****cnssdaemon pid=3070********* [ 24.691105] wlan: [3169:I:ANY] =======ol_if_register_wifi3_0========== [ 24.691105] [ 24.691153] wlan: [3169:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:1 with soc_ops:ffffffbffce78008 [ 24.698103] remoteproc remoteproc0: powering up q6v5-m3 [ 24.733035] remoteproc remoteproc0: Booting fw image IPQ8074/m3_fw.mdt, size 284 [ 24.733070] Sanity check passed for M3 image [ 24.807344] remoteproc remoteproc0: remote processor q6v5-m3 is now up [ 24.807435] wlan: [3169:I:ANY] ol_ath_ahb_ssr: 192: ol_ath_ahb_ssr: SSR event 2 [ 24.812893] <SSR>: glink SUBSYS_BEFOER_POWERUP reinit done [ 24.820561] remoteproc remoteproc1: powering up q6v5-wcss [ 24.827381] remoteproc remoteproc1: Booting fw image IPQ8074/q6_fw.mdt, size 668 [ 24.831289] Sanity check passed for the image [ 3257(lan)] [smartip_get_cfg 167] key:gw value:192.168.0.1 [ 3257(lan)] [smartip_get_cfg 167] key:lanip value:192.168.0.1 [ 3257(lan)] [smartip_get_cfg 167] key:lantype value:1 [ 3257(lan)] [smartip_get_cfg 167] key:mask value:255.255.252.0 [ 3257(lan)] [smartip_get_lan_status 465] Error: open /sys/class/net//carrier fail [ 3257(lan)] [smartip_get_lan_status 465] Error: open /sys/class/net//carrier fail timestamp 1774746000 M3.5.0/03:00 timestamp 1792893600 M10.4.0/04:00 GMT-02:00TMG,M3.5.0/03:00,M10.4.0/04:00 [ 3257(lan)] [smartip_check_online 670] open /tmp/is_online error... [ 26.184551] glink_core_link_up glink is up [ 26.184762] glink_xprt_open_event [ 26.184832] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled [ 26.187576] Subsystem error monitoring/handling services are up [ 26.187598] remoteproc remoteproc1: remote processor q6v5-wcss is now up [ 26.187648] wlan: [3169:I:ANY] ol_ath_ahb_ssr: 192: ol_ath_ahb_ssr: SSR event 3 [ 26.211200] diag: In diag_send_feature_mask_update, control channel is not open, p: 2, ffffffbffc48c448 [ 26.220866] cnss: QMI WLFW service connected, state: 0x1 [ 26.226585] cnss: device_id : 65534 mem mode : [1] [ 26.232825] cnss: Boardid from dts:292,FW:ff [ 26.237305] cnss: BDF location : 0x000000004b0c0000 [ 26.240975] cnss: BDF IPQ8074/bdwlan.b292 size 131072 [ 26.246058] cnss: BDF download response , result: 0, err: 0x0 [ 26.251288] cnss: per device BDF location : 0x000000004b0e0000 [ 26.256814] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000 [ 26.264388] cnss: BDF download response , result: 0, err: 0x0 [ 26.294826] wlan: [3169:I:ANY] pld_ahb_wlan_enable: 681: cnss_mode: Cold boot calibration [ 26.366100] wlan: [3169:I:ANY] Coldboot calibration wait started [ 26.366100] [ 3257(lan)] [smartip_check_online 670] open /tmp/is_online error... [ 3257(lan)] [smartip_check_online 670] open /tmp/is_online error... [ 3257(lan)] [smartip_check_online 670] open /tmp/is_online error... [ 3257(lan)] [smartip_check_online 670] open /tmp/is_online error... [ 3257(lan)] [smartip_check_online 670] open /tmp/is_online error... [ 3257(lan)] [smartip_check_online 670] open /tmp/is_online error... [ 31.866522] wlan: [3169:I:ANY] Coldboot calibration wait ended [ 31.866522] [ 31.867453] wlan: [3169:I:ANY] ol_ath_do_cold_boot_calibration: 505: Coldboot calib successful: radio_id 0x65534 [ 31.873509] wlan: [3169:I:ANY] init_ath_pci_3_0: 151: 6ath_ol_pci_wifi3.0: (Atheros/multi-bss) [ 31.883120] MINIDUMP VA .bss start=ffffffbffce78400 module=wifi_3_0 [ 31.908742] wlan: [3424:I:ANY] ol_ath_ahb_ssr: 192: ol_ath_ahb_ssr: SSR event 0 [ 31.934393] remoteproc remoteproc1: stopped remote processor q6v5-wcss [ 31.934454] wlan: [3424:I:ANY] ol_ath_ahb_ssr: 192: ol_ath_ahb_ssr: SSR event 1 [ 31.939995] glink_core_link_down glink is down [ 31.947143] <SSR>: glink SUBSYS_AFTER_SHUTDOWN cleanup done [ 31.951568] remoteproc remoteproc0: stopped remote processor q6v5-m3 [ 31.974043] cnss: QMI WLFW service disconnected, state: 0x7 [ 31.993974] glink_xprt_close_event [ 32.225351] MINIDUMP VA .bss start=ffffffbffcfa6b00 module=qca_ol [ 32.239390] wlan: [3437:I:ANY] =======ol_if_register_wifi3_0========== [ 32.239390] [ 32.239437] wlan: [3437:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:1 with soc_ops:ffffffbffd085008 [ 32.246427] remoteproc remoteproc0: powering up q6v5-m3 [ 32.258827] remoteproc remoteproc0: Booting fw image IPQ8074/m3_fw.mdt, size 284 [ 32.263468] Sanity check passed for M3 image [ 32.272240] remoteproc remoteproc0: remote processor q6v5-m3 is now up [ 32.275430] wlan: [3437:I:ANY] ol_ath_ahb_ssr: 192: ol_ath_ahb_ssr: SSR event 2 [ 32.281821] <SSR>: glink SUBSYS_BEFOER_POWERUP reinit done [ 32.288927] remoteproc remoteproc1: powering up q6v5-wcss [ 32.294744] remoteproc remoteproc1: Booting fw image IPQ8074/q6_fw.mdt, size 668 [ 32.300191] Sanity check passed for the image [ 3257(lan)] [smartip_check_online 670] open /tmp/is_online error... [ 32.670431] glink_core_link_up glink is up [ 32.670643] glink_xprt_open_event [ 32.673495] Subsystem error monitoring/handling services are up [ 32.673526] remoteproc remoteproc1: remote processor q6v5-wcss is now up [ 32.673564] wlan: [3437:I:ANY] ol_ath_ahb_ssr: 192: ol_ath_ahb_ssr: SSR event 3 [ 32.689634] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled [ 32.748075] Ebtables v2.0 unregistered [ 32.795276] cnss: QMI WLFW service connected, state: 0x1 [ 32.795806] cnss: device_id : 65534 mem mode : [1] [ 32.800405] cnss: Boardid from dts:292,FW:ff [ 32.804745] cnss: BDF location : 0x000000004b0c0000 [ 32.808676] cnss: BDF IPQ8074/bdwlan.b292 size 131072 [ 32.818365] cnss: BDF download response , result: 0, err: 0x0 [ 32.819022] cnss: per device BDF location : 0x000000004b0e0000 [ 32.824459] cnss: CALDATA IPQ8074/caldata.bin size 131072 offset 0x20000 [ 32.832229] cnss: BDF download response , result: 0, err: 0x0 [ 32.875951] wlan: [3437:I:ANY] pld_ahb_wlan_enable: 689: cnss_mode: Mission mode [ 32.885434] wlan: [3437:I:ANY] qca_napi_create: 369: qca_napi_create: napi instance 0 created on pipe 4 [ 32.885751] wlan: [3437:I:ANY] __ol_ath_attach: 3520: Allocated soc ffffffc014e00880 [ 32.932643] wlan: [3437:E:CONFIG] cfg_uint_item_handler: 171: dp_int_timer_threshold_tx=1000 - Out of range [8, 100]; Using 1000 [ 32.933021] wlan: [3437:I:ANY] osif_nss_wifi_soc_setup: 177: nss-wifili:#1 register wifili function for soc [ 32.943337] wlan: [3437:I:ANY] osif_nss_wifi_soc_setup: 189: nss register id -1 nss config 3 Target Type 18 [ 32.953140] wlan: [3437:I:ANY] __ol_ath_attach: 3746: dev name soc0 [ 32.963117] wlan: [3437:I:ANY] ol_ath_soc_attach: 7031: WMI attached. wmi_handle ffffffc016e96400 [ 32.969067] wlan: [3437:I:ANY] htc_wmi_init: 6320: htc_wmi_init() HT Create . ffffffc016ec0000 [ 32.977947] wlan: [3437:I:ANY] htc_wmi_init: 6327: htc_wmi_init() Skipping BMI Done. [ 32.986542] wlan: [3437:I:ANY] htc_wmi_init: 6384: [htc_wmi_init:6384] host_enable 0 nss_nwifi_offload 0 [ 32.998467] wlan: [3437:I:ANY] ol_target_init_complete: 6502: CDP soc attach success [ 33.003995] wlan: [3437:I:ANY] ol_target_init_complete: 6509: Soc attach success NSS config 0 [ 33.011826] wlan: [3437:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ffffffc016ec0000, ep 2, value 1 [ 33.020196] wlan: [3437:I:ANY] htc_set_async_ep: 428: htc_set_async_ep: htc_handle ffffffc016ec0000, ep 3, value 1 [ 33.034046] wlan: [6:I:TIF] HE_CAP Info = 1a08010d [ 33.040764] wlan: [6:I:TIF] Num HW modes = 1 [ 33.045567] wlan: [6:I:TIF] Num PHY = 2 [ 33.049953] wlan: [6:I:TIF] Preferred HW Mode = 1 Num Radios = 2 [ 33.053520] wlan: [6:I:TIF] init_deinit_add_11ax_modes: 1440: Adding 11ax regulatory modes, [ 33.059806] wlan: [6:I:TIF] init_deinit_add_11ax_modes: 1444: phy_id = 0 wireless modes = f97f9001 [ 33.067926] wlan: [6:I:TIF] init_deinit_add_11ax_modes: 1440: Adding 11ax regulatory modes, [ 33.076903] wlan: [6:I:TIF] init_deinit_add_11ax_modes: 1444: phy_id = 1 wireless modes = 680680c [ 33.085231] wlan: [6:I:TIF] init_deinit_add_11ax_modes: 1467: hw_mode_id = 1 phy_id = 0 wireless modes = f97f9001 [ 33.094266] wlan: [6:I:TIF] init_deinit_add_11ax_modes: 1467: hw_mode_id = 1 phy_id = 1 wireless modes = 680680c [ 33.104901] wlan: [6:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 389: dfs_offload 1 [ 33.114852] wlan: [6:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 1579: dfs->dfs_psoc_idx: 0 [ 33.124654] wlan: [6:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_agile_soc_obj_init: 1585: dfs_soc_obj->num_dfs_privs: 1 [ 33.134149] wlan: [6:I:dfs] WLAN_DEBUG_DFS_ALWAYS : wlan_dfs_pdev_obj_create_notification: 361: Do not allocate DFS object for 2G, pdev_id = 1 [ 33.154526] wlan: [6:I:TIF] init_deinit_update_pdev_tgt_info: 1082: CDP PDEV ATTACH success [ 33.160894] wlan: [6:I:TIF] init_deinit_update_pdev_tgt_info: 1082: CDP PDEV ATTACH success [ 33.265669] wlan: [6:I:ANY] copy_fw_abi_version_tlv: 6649: copy_fw_abi_version_tlv: INIT_CMD version: 1, 0, 0x5f414351, 0x4c4d, 0x0, 0x0 [ 33.374583] wlan: [6:I:ANY] dp_peer_map_attach_wifi3: 8665: dp_peer_map_attach_wifi3 max_peers 311, max_ast_index: 1040 [ 33.374583] [ 33.374726] wlan: [6:I:ANY] ready_extract_init_status_tlv: 8473: ready_extract_init_status_tlv:0 [ 33.385980] wlan: [3437:I:ANY] ol_ath_connect_htc: 1236: WMI is ready [ 3257(lan)] [smartip_check_online 670] open /tmp/is_online error... [ 33.447973] wlan: [3437:E:WMI] wmi_unified_register_event_handler: Event id 141 is unavailable [ 33.448013] wlan: [3437:E:WMI] wmi_unified_register_event_handler: Event id 137 is unavailable [ 33.455601] wlan: [3437:I:ANY] ol_ath_soc_attach: 7118: connect HTC [ 33.464118] wlan: [3437:I:ANY] ol_ath_soc_attach: 7119: bypasswmi : 0 [ 33.470236] wlan: [3437:E:WMI] event handler already registered 0x27001 [ 33.476871] wlan: [3437:E:WMI] event handler already registered 0x27002 [ 33.483257] wlan: [3437:E:WMI] event handler already registered 0x27003 [ 33.489913] wlan: [3437:E:WMI] wmi_unified_register_event_handler: Event id 38 is unavailable [ 33.496495] wlan: [3437:E:WMI] wmi_unified_register_event_handler: Event id 138 is unavailable [ 33.505196] wlan: [3437:E:WMI] wmi_unified_register_event_handler: Event id 139 is unavailable [ 33.513657] wlan: [3437:E:WMI] wmi_unified_register_event_handler: Event id 55 is unavailable [ 33.522280] wlan: [3437:E:WMI] wmi_unified_register_event_handler: Event id 49 is unavailable [ 33.530904] wlan: [3437:E:WMI] wmi_unified_register_event_handler: Event id 25 is unavailable [ 33.539393] wlan: [3437:I:ANY] ol_ath_soc_attach: 7199: ol_ath_soc_attach() UMAC attach . [ 33.547979] wlan: [3437:I:ANY] __ol_ath_attach: 3862: pdev_netdev name wifi0 [ 33.556076] wlan: [3437:I:ANY] __ol_ath_attach: 3908: Skip txrx_pdev_attach_target [ 33.563208] wlan: [3437:I:ANY] __ol_ath_attach: 3933: BURSTING enabled by default [ 33.571032] wlan: [3437:I:ANY] ol_ath_pdev_attach: 8496: interface_id 0 [ 33.578212] wlan: [3437:I:TIF] ol_ath_pdev_regdmn_init: 7360: phy id = 0 Modes supported [ 33.584604] wlan: [3437:I:TIF] ol_ath_pdev_regdmn_init: 7367: 11b = 0 11g = 0 11a = 1 11n = 1 11ac = 1 11ax = 1 [ 33.592909] wlan: [3437:I:TIF] ol_ath_pdev_regdmn_init: 7376: Reg cap - phy_id = 0 supp_bnd = 2, modes = f97f9001, lo_2g = 0, hi_2g = 0 lo_g5 = 4910, hi_5g = 6100 [ 33.603202] wlan: [3437:I:ANY] ol_ath_update_wireless_modes: 1351: wireless_modes = f97f9001 before update [ 33.617521] wlan: [3437:I:ANY] ol_ath_update_wireless_modes: 1366: Wireless_modes = f97f9001 after update [ 33.627220] wlan: [3437:I:ANY] ol_ath_update_ext_caps: 1916: 11ax 5G supported case [ 33.637052] wlan: [3437:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed [ 33.644411] wlan: [3437:I:ANY] ieee80211_cbs_init [ 33.650872] wlan: [3437:I:ANY] CBS Inited [ 33.650872] [ 33.655791] wlan: [3437:I:ANY] acfg_attach: 3473: acfg_attach: 3473: Netlink socket created:ffffffc01daa0800 [ 33.661224] wlan: [3437:I:ANY] ol_if_eeprom_attach: 1459: rate power table override is only supported for AR98XX [ 33.671220] wlan: [3437:I:ANY] ol_ath_stats_attach: 2133: periodic_chan_stats: 1 [ 33.682715] wlan: [3437:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 25 [ 33.688783] wlan: [0:I:ANY] ol_ath_pdev_attach: 8860: Set global_ic[1], ptr:ffffffbffca97ee8 [ 33.696120] wlan: [0:I:ANY] dp_lag_soc_enable: 91: pdev(ffffffc01516ac08) Enabling DBDC Repeater 1 [ 33.704580] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 44: pdev(ffffffc01516ac08) is_primary 1 [ 33.704658] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed [ 33.722352] wlan: [3437:I:ANY] ol_ath_pdev_attach: 8989: Pdev = 0 Number of peers = 137 [ 33.731039] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 13838: twt enabled. [ 33.731039] [ 33.733259] wlan: [3437:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 560: cfg block channel list is empty [ 33.733267] wlan: [3437:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3451: pdev_idx = 0 tx_desc_limit = 32768 [ 33.733294] wlan: [3437:I:ANY] osif_wrap_attach: 239: osif wrap attached [ 33.733294] [ 33.733299] wlan: [3437:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done [ 33.733299] [ 33.733308] wlan: [3437:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =ffffffc01daa0000 ic->ic_wrap_com=ffffffc01daa0000 &wrap_com->wc_devt=ffffffc01daa0000 [ 33.733308] [ 33.733336] wlan: [3437:I:ANY] __ol_ath_attach: 4114: needed_headroom reservation 60 [ 33.733343] wlan: [3437:I:ANY] ol_ath_enable_fraglist: 3010: Enabled Fraglist bit for the radio wifi0 features 41 [ 33.733431] wlan: [3437:I:ANY] wlan_cfg80211_init: 10893: Number of 5G channels: 25 [ 33.733743] wlan: [3437:I:ANY] ieee80211_cfg80211_radio_attach: 10987: ic: 0xffffffc013a40880, wdev: 0xffffffc013a50a68, wiphy: 0xffffffc013aac2a0, netdev: 0xffffffc013a40000 [ 33.734606] wlan: [3437:I:ANY] __ol_ath_attach: 3862: pdev_netdev name wifi1 [ 33.734629] wlan: [3437:I:ANY] __ol_ath_attach: 3908: Skip txrx_pdev_attach_target [ 33.734634] wlan: [3437:I:ANY] __ol_ath_attach: 3933: BURSTING enabled by default [ 33.734702] wlan: [3437:I:ANY] ol_ath_pdev_attach: 8496: interface_id 1 [ 33.734720] wlan: [3437:I:TIF] ol_ath_pdev_regdmn_init: 7360: phy id = 1 Modes supported [ 33.734727] wlan: [3437:I:TIF] ol_ath_pdev_regdmn_init: 7367: 11b = 1 11g = 1 11a = 0 11n = 1 11ac = 1 11ax = 1 [ 33.734736] wlan: [3437:I:TIF] ol_ath_pdev_regdmn_init: 7376: Reg cap - phy_id = 1 supp_bnd = 1, modes = 680680c, lo_2g = 2312, hi_2g = 2732 lo_g5 = 0, hi_5g = 0 [ 33.734742] wlan: [3437:I:ANY] ol_ath_update_wireless_modes: 1351: wireless_modes = 680680c before update [ 33.734747] wlan: [3437:I:ANY] ol_ath_update_wireless_modes: 1366: Wireless_modes = 680680c after update [ 33.734753] wlan: [3437:I:ANY] ol_ath_update_ext_caps: 1924: 11ax 2G supported case [ 33.734897] wlan: [3437:I:ANY] ol_resmgr_create: 223: OL Resmgr Init-ed [ 33.734987] wlan: [3437:I:ANY] ieee80211_cbs_init [ 33.734991] wlan: [3437:I:ANY] CBS Inited [ 33.734991] [ 33.735020] wlan: [3437:I:ANY] acfg_attach: 3448: Offload using existing sock ffffffc01daa0800 [ 33.735033] wlan: [3437:I:ANY] ol_if_eeprom_attach: 1459: rate power table override is only supported for AR98XX [ 33.735041] wlan: [3437:I:ANY] ol_ath_stats_attach: 2133: periodic_chan_stats: 1 [ 33.735327] wlan: [3437:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 11 [ 33.735358] wlan: [0:I:ANY] ol_ath_pdev_attach: 8860: Set global_ic[2], ptr:ffffffbffca97ee8 [ 33.735366] wlan: [0:I:ANY] dp_lag_soc_enable: 91: pdev(ffffffc01516b208) Enabling DBDC Repeater 1 [ 33.735407] wlan: [0:I:ANY] dp_lag_pdev_set_primary_radio: 44: pdev(ffffffc01516b208) is_primary 0 [ 33.735423] wlan: [3437:I:ANY] ol_ath_pdev_attach: 8989: Pdev = 1 Number of peers = 137 [ 33.736751] wlan: [3437:E:WMI] event handler already registered 0x6019 [ 33.737752] wlan: [3437:I:ANY] ol_ath_pri20_cfg_blockchanlist_parse: 560: cfg block channel list is empty [ 33.737759] wlan: [3437:I:ANY] ol_ath_configure_cong_ctrl_max_msdus: 3451: pdev_idx = 1 tx_desc_limit = 16384 [ 33.737782] wlan: [3437:I:ANY] osif_wrap_attach: 239: osif wrap attached [ 33.737782] [ 33.737787] wlan: [3437:I:ANY] osif_wrap_devt_init: 201: osif wrap dev table init done [ 33.737787] [ 33.737796] wlan: [3437:I:ANY] osif_wrap_attach: 247: Wrap Attached: Wrap_com =ffffffc00ee79400 ic->ic_wrap_com=ffffffc00ee79400 &wrap_com->wc_devt=ffffffc00ee79400 [ 33.737796] [ 33.737828] wlan: [3437:I:ANY] __ol_ath_attach: 4114: needed_headroom reservation 60 [ 33.737835] wlan: [3437:I:ANY] ol_ath_enable_fraglist: 3010: Enabled Fraglist bit for the radio wifi1 features 41 [ 33.737862] wlan: [3437:I:ANY] wlan_cfg80211_init: 10881: Number of 2G channels: 11 [ 33.738111] wlan: [3437:I:ANY] ieee80211_cfg80211_radio_attach: 10987: ic: 0xffffffc013a80880, wdev: 0xffffffc013a90a68, wiphy: 0xffffffc00ee81aa0, netdev: 0xffffffc013a80000 [ 33.738794] wlan: [3437:I:Dynamic Mode Change] ol_ath_check_and_reconfig_hw_mode: 3420: Running with HW mode = 1 [ 33.739173] wlan: [3437:E:QLD] qld_register: 108: Handle or address is NULL [ 33.739193] wlan: [3437:I:ANY] wlan_pdev_operation: 744: num_radios=1, wifi_radios[0].sc = ffffffc013a40880_radio_type = 2 [ 33.739201] wlan: [3437:I:ANY] wlan_pdev_operation: 744: num_radios=2, wifi_radios[1].sc = ffffffc013a80880_radio_type = 2 [ 33.739230] wlan: [3437:I:ANY] init_ath_pci_3_0: 151: 6ath_ol_pci_wifi3.0: (Atheros/multi-bss) [ 34.156250] [ 34.156250] MINIDUMP VA .bss start=ffffffbffd085400 module=wifi_3_0 [ 34.156250] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed [ 34.173480] wlan: [0:I:ANY] ol_ath_twt_enable_complete_event_handler: 13838: twt enabled. [ 34.173480] unload shortcut_fe_drv here [ 34.201057] wlan: [3550:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:0 with soc_ops:ffffffbffd12d548 [ 34.201105] wlan: [3550:I:ANY] osif_nss_register_module: 90: NSS wifi ops registered for target_type:0 with soc_ops:ffffffbffd12d548 [ 34.212785] wlan: [3550:I:ANY] init_ath_pci_2_0: 143: 6ath_ol_pci_2_0: (Atheros/multi-bss) QCAWIFICFG80211 No Direct-Attach chipsets found. cfg80211tool wifi1 setCountry DE [ 3257(lan)] [smartip_check_online 670] open /tmp/is_online error... [ 34.483860] wlan: [3717:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 13 [ 34.484032] wlan: [3717:I:ANY] number of channels: 2G = 13 5G = 0 [ 34.490353] wlan: [3717:I:ANY] wlan_cfg80211_set_country: 6059: wlan_cfg80211_set_country: Country: DE ret: 0 cfg80211tool wifi1 bsta_fixed_idmask 255 cfg80211tool wifi1 set_bcnburst 0 cfg80211tool wifi1 sIgmpDscpOvrid 1 iptv.init start iptv iptv start_service cfg80211tool wifi1 sIgmpDscpTidMap 6 self iptv_port is other cfg80211tool wifi1 enable_ol_stats 1 cfg80211tool wifi1 setHwaddr 40:3F:8C:79:57:9E [ 34.761810] wlan: [3820:I:ANY] wlan_cfg80211_set_hwaddr: 6132: wlan_cfg80211_set_hwaddr :40:3f:8c:79:57:9e ret: 0 cfg80211tool wifi1 txbf_snd_int 100 [ 34.811919] wlan: [3831:I:ANY] ol_ath_set_config_param: 1577: set TXBF_SND_PERIOD: value 100 wmi_status 0 cfg80211tool wifi1 obss_rssi_th 35 wanDetect: ERR: is_force:0, force_port:-1 wanDetect: INFO: move all interface to br-lan wanDetect: INFO: eth0 was already under br-lan! wanDetect: INFO: eth1 was already under br-lan! uci: Entry not found uci: Entry not found cfg80211tool wifi1 obss_rxrssi_th 35 wanDetect: INFO: Goto uloop_run cfg80211tool wifi1 dbdc_enable 0 conn-indicator: INFO: -- running -- conn-indicator: NOTE: BINDING state: -1 -> 3 conn-indicator: INFO: <30000307> Invoke led: conn[2] conn-indicator: NOTE: Mode changed: Unknown -> AP conn-indicator: NOTE: Role changed: Unknown -> RE conn-indicator: NOTE: Network type: Unknown -> RE [ 34.970553] wlan: [0:I:ANY] dp_lag_soc_enable: 91: pdev(ffffffc01516b208) Enabling DBDC Repeater 0 [ 34.970663] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed [ 34.978461] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed [ 34.986754] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed cfg80211tool wifi1 no_vlan 1 ===== TIPC have already enabled ==== cfg80211tool wifi1 discon_time 10 [ 35.091076] wlan: [0:I:ANY] ol_ath_set_config_param: 2328: Disconnect_timeout value: 10 cfg80211tool wifi1 reconfig_time 60 [ 35.107903] Started in network mode [ 35.107935] Own node address <7.112.2>, network identity 4711 [ 35.115594] Enabled bearer <deco:br-lan:0>, discovery domain <7.112.0>, priority 10 [ 35.150412] wlan: [0:I:ANY] ol_ath_set_config_param: 2334: Reconfiguration_timeout value:60 tipc-server: INFO: -- running -- tipc-server: INFO: server radar: port {18888,100,200} created tipc-server: INFO: mode is RE tipc-server: INFO: mode is RE tipc-server: INFO: mode is RE tipc-server: INFO: server RE: port {6000,100,100} created cfg80211tool wifi1 fc_buf0_max 8192 cfg80211tool wifi1 fc_buf1_max 8192 cfg80211tool wifi1 fc_buf2_max 8192 cfg80211tool wifi1 fc_buf3_max 8192 ===cloud-report=== no need to start cfg80211tool wifi1 get_rxchainmask do nothing for AP mode number of vifs: ath0 ath01 ath02 wlanconfig ath0 create wlandev wifi1 wlanmode ap -cfg80211 smart_home_schedule reload_service [ 35.809024] wlan: [4130:I:ANY] wlan_cfg80211_add_virtual_intf: 325: proprietary mode 6 for interface: ath0 : clone params: 0x00000001 [ 35.811090] wlan: [4130:I:ANY] osifp_create_wlan_vap: 10419: VDEV Create 40:3f:8c:79:57:9e [ 35.823106] wlan: [4130:E:CMN_MLME] mlme_vdev_ext_obj_create: 1389: VDEV MLME obj is creation [ 35.831257] wlan: [4130:I:ANY] wlan_vap_create: 1594: enter. devhandle=0xffffffc013a80880, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 35.831257] [ 35.840177] wlan: [4130:I:ANY] ol_ath_vap_set_param: 1121: Setting SGI value: 1 [ 35.853417] wlan: [4130:I:ANY] ol_ath_vap_set_param: 2149: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1 [ 35.860038] wlan: [4130:I:ANY] ol_ath_vap_set_param: 2159: he_bf_cap=0x7b [ 35.873579] wlan: [4130:I:ANY] ol_ath_vap_set_param: 2174: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 35.880561] wlan: [4130:I:ANY] MBO Initialized [ 35.894524] wlan: [4130:I:ANY] OCE Initialized [ 35.898835] wlan: [4130:I:ANY] osif_nss_ol_vap_create: 1268: NSS wifi offload VAP create IF 33 nss_id -1 [ 35.903253] wlan: [4130:I:ANY] NSS radio_if 32 [ 35.913003] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1020: VDEV configuration success: 0 [ 35.917267] wlan: [4130:I:ANY] osif_nss_ol_vap_create: 1376: vap create ffffffc01b63c880 : if_num 33 [ 35.925540] wlan: [4130:I:ANY] wlan_vap_create: 1627: exit [ 35.934877] wlan: [4130:E:ANY] Smart Antenna is not supported [ 35.940431] wlan: [4130:E:ANY] Smart Antenna is not supported [ 35.946094] wlan: [4130:I:ANY] osif_create_vap_complete: 10617: TX Checksum:1|SG:1|TSO:1|LRO:0 [ 35.951774] wlan: [4130:I:ANY] WLAN-NSS: VAP NSS ops initialized [ 35.961409] wlan: [4130:I:ANY] VAP device ath0 created osifp: (ffffffc01b63c880) os_if: (ffffffc00e4e0000) [ 35.967195] wlan: [4154:I:ANY] ol_ath_ucfg_btcoex_duty_cycle: 862: btcoex_duty_cycle service not started. btcoex_support:0 btcoex_duty_cycle:0 maclist_smart_home: ### smart_home_schedule is NOT ready for AP mode yet### [IOT-CENTER][setDutyCycle:1379]: Error: GET 2.4G WIFI DEVICE wifi1 ===url_class=== no need to start cfg80211tool ath0 mode 11GHE40 ===aviraserviceselector=== no need to start cfg80211tool ath0 mode 11GHE40 ===avirasentinelfull=== no need to start cfg80211tool ath0 channel 0 ===avirasentinellite=== no need to start cfg80211tool ath0 hide_ssid 0 cfg80211tool ath0 nrshareflag 7 cfg80211tool ath0 disablecoext 1 cfg80211tool ath0 wds 1 cfg80211tool ath0 backhaul 0 =============== app-dpi start =============== do nothing for AP mode cfg80211tool ath0 en_sae_pwid 1 =============== app-qos try to start =============== do nothing for AP mode cfg80211tool ath0 en_sae_pwid 1 cfg80211tool ath0 uapsd 1 manager permission has been set, no need to set again cfg80211tool ath0 vap_ind 0 =========> check cloud_config.device_status.username_md5 cloud config username_md5 is already added... cfg80211tool ath0 extap 0 client_mgmt: ERR: unexpected ap vapname = ath06[ 36.912320] g_back_dev_num:5 client_mgmt: ERR: unexpected ap vapname = ath16 client_mgmt: ERR: unexpected ap vapname = ath07 client_mgmt: ERR: unexpected ap vapname = ath17 client_mgmt: ERR: unexpected ap vapname = ath25 cfg80211tool ath0 stafwd 0 cfg80211tool ath0 maccmd_sec 2 cfg80211tool ath0 maxsta 128 [ 37.230783] wlan: [4512:I:ANY] ieee80211_ucfg_setparam: 1453: Setting Max Stations:128 cfg80211tool ath0 blockdfschan 1 guest-eth: Start to set guest vlan cfg80211tool ath0 rrm 1 guest-eth: Ignore system signal guest-eth: Lock vlan.lock guest-eth: RE role, eth1 set iptv port, vlan id is 591 cfg80211tool ath0 vhtsubfee 1 mac:40-3F-8C-79-57-9C role:RE mac:40-3F-8C-79-57-90 role:AP update fap: 40:3F:8C:79:57:90 cfg80211tool ath0 vhtmubfee 1 cfg80211tool ath0 vhtsubfer 1 cfg80211tool ath0 vhtmubfer 1 cfg80211tool ath0 he_subfee 1 [ 37.798727] wlan: [4694:I:ANY] wlan_set_param: 2953: HE SU BFEE already set with this value =1 cfg80211tool ath0 he_subfer 1 *****/tmp/ipv6_firewall/op_rule_id file not found, create it.***** NO necessary to load ipv6 firewall, return. [ 37.887602] wlan: [4715:I:ANY] wlan_set_param: 2972: HE SU BFER already set with this value =1 cfg80211tool ath0 he_mubfee 1 [ 37.974816] wlan: [4755:I:ANY] ieee80211_ucfg_setparam: 4918: HE MU BFEE only supported in STA mode cfg80211tool ath0 he_mubfer 1 [ 38.072066] wlan: [4780:I:ANY] wlan_set_param: 3018: HE MU BFER already set with this value =1 cfg80211tool ath0 athnewind 1 iwpriv ath0 he_ulmumimo 0 [ 38.193093] wlan: [4847:I:ANY] ol_ath_vap_set_param: 2149: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:0 [ 38.193145] wlan: [4847:I:ANY] ol_ath_vap_set_param: 2159: he_bf_cap=0x3b iwpriv ath0 he_ulofdma 0 [ 38.244881] wlan: [4858:I:ANY] ol_ath_vap_set_param: 2149: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:0|ul_mumimo:0 [ 38.244934] wlan: [4858:I:ANY] ol_ath_vap_set_param: 2159: he_bf_cap=0x1b cfg80211tool ath0 ap_bridge 1 [ 38.594146] device ath0 entered promiscuous mode [ 38.594297] br-lan: port 3(ath0) entered forwarding state [ 38.597898] br-lan: port 3(ath0) entered forwarding state [ 38.603473] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 38.610042] wlan: [877:I:ANY] wlan_cfg80211_do_acs: 3474: vap-0(ath0):ACS Params [ 38.615094] wlan: [877:I:ANY] wlan_cfg80211_do_acs: 3477: ht_enabled:1|ht40_enabled:0|vht_enabled:1|hw_mode:29|chwidth:20| [ 38.622424] wlan: [877:I:ANY] ieee80211_autoselect_infra_bss_channel: 4059: ACS started: vap:0xffffffc00e4e0000 [ 38.774390] wlan: [5060:I:ANY] osif_nss_vdev_set_cfg: 1999: setting hifi mode 5 target type 0 [ 38.774429] wlan: [5060:I:ANY] osif_nss_vdev_set_cfg: 2003: Mcast command 5 cfg80211tool ath0 11ngvhtintop 1 wlanconfig ath01 create wlandev wifi1 wlanmode ap -cfg80211 [ 38.936662] wlan: [5152:I:ANY] wlan_cfg80211_add_virtual_intf: 325: proprietary mode 6 for interface: ath01 : clone params: 0x00000001 [ 38.936750] wlan: [5152:I:ANY] osifp_create_wlan_vap: 10419: VDEV Create 46:3f:8c:79:57:9e [ 38.947859] wlan: [5152:E:CMN_MLME] mlme_vdev_ext_obj_create: 1389: VDEV MLME obj is creation [ 38.956060] wlan: [5152:I:ANY] wlan_vap_create: 1594: enter. devhandle=0xffffffc013a80880, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 38.956060] [ 38.964826] wlan: [5152:I:ANY] ol_ath_vap_set_param: 1121: Setting SGI value: 1 [ 38.977783] wlan: [5152:I:ANY] ol_ath_vap_set_param: 2149: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1 [ 38.984755] wlan: [5152:I:ANY] ol_ath_vap_set_param: 2159: he_bf_cap=0x7b [ 38.998317] wlan: [5152:I:ANY] ol_ath_vap_set_param: 2174: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 39.005308] wlan: [5152:I:ANY] MBO Initialized [ 39.019321] wlan: [5152:I:ANY] OCE Initialized [ 39.024074] wlan: [5152:I:ANY] osif_nss_ol_vap_create: 1268: NSS wifi offload VAP create IF 34 nss_id -1 [ 39.028375] wlan: [5152:I:ANY] NSS radio_if 32 [ 39.037785] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1020: VDEV configuration success: 0 [ 39.042059] wlan: [5152:I:ANY] osif_nss_ol_vap_create: 1376: vap create ffffffc01b57e880 : if_num 34 [ 39.050338] wlan: [5152:I:ANY] wlan_vap_create: 1627: exit [ 39.059667] wlan: [5152:E:ANY] Smart Antenna is not supported [ 39.065257] wlan: [5152:E:ANY] Smart Antenna is not supported [ 39.070836] wlan: [5152:I:ANY] osif_create_vap_complete: 10617: TX Checksum:1|SG:1|TSO:1|LRO:0 [ 39.076602] wlan: [5152:I:ANY] WLAN-NSS: VAP NSS ops initialized [ 39.086939] wlan: [5152:I:ANY] VAP device ath01 created osifp: (ffffffc01b57e880) os_if: (ffffffc00e258000) cfg80211tool ath01 mode 11GHE40 cfg80211tool ath01 mode 11GHE40 cfg80211tool ath01 channel 0 cfg80211tool ath01 hide_ssid 0 cfg80211tool ath01 nrshareflag 7 cfg80211tool ath01 disablecoext 1 cfg80211tool ath01 wds 1 cfg80211tool ath01 backhaul 0 tp_security: snort_disable start cfg80211tool ath01 uapsd 1 tp_security: snort_disable end cfg80211tool ath01 vap_ind 0 cfg80211tool ath01 extap 0 cfg80211tool ath01 stafwd 0 wanDetect: ERR: port update : eth0 first update init timeout event: Resource temporarily unavailable first update init timeout event: Resource temporarily unavailable cfg80211tool ath01 maccmd_sec 2 cfg80211tool ath01 maxsta 128 [ 40.098867] wlan: [5447:I:ANY] ieee80211_ucfg_setparam: 1453: Setting Max Stations:128 cfg80211tool ath01 blockdfschan 1 first update init timeout event: No such file or directory tipc-server: INFO: FAP has been lost, need to update led cfg80211tool ath01 rrm 1 /lib/sync-server/scripts/probe:408: Warning: I have no IP iwpriv ath01 he_ulmumimo 0 [ 40.288483] wlan: [5481:I:ANY] ol_ath_vap_set_param: 2149: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:0 [ 40.288534] wlan: [5481:I:ANY] ol_ath_vap_set_param: 2159: he_bf_cap=0x3b iwpriv ath01 he_ulofdma 0 [ 40.312691] wlan: [5484:I:ANY] ol_ath_vap_set_param: 2149: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:0|ul_mumimo:0 [ 40.312741] wlan: [5484:I:ANY] ol_ath_vap_set_param: 2159: he_bf_cap=0x1b cfg80211tool ath01 ap_bridge 0 [ 40.549635] device ath01 entered promiscuous mode [ 40.549723] br-lan: port 4(ath01) entered forwarding state [ 40.553336] br-lan: port 4(ath01) entered forwarding state [ 40.559498] wlan: [877:I:ANY] wlan_cfg80211_do_acs: 3474: vap-1(ath01):ACS Params [ 40.564313] wlan: [877:I:ANY] wlan_cfg80211_do_acs: 3477: ht_enabled:1|ht40_enabled:0|vht_enabled:1|hw_mode:29|chwidth:20| [ 40.571740] wlan: [877:I:ANY] ieee80211_autoselect_infra_bss_channel: 4059: ACS started: vap:0xffffffc00e258000 cfg80211tool ath01 11ngvhtintop 1 wlanconfig ath02 create wlandev wifi1 wlanmode ap -cfg80211 [ 40.816684] wlan: [5539:I:ANY] wlan_cfg80211_add_virtual_intf: 325: proprietary mode 6 for interface: ath02 : clone params: 0x00000001 [ 40.816776] wlan: [5539:I:ANY] osifp_create_wlan_vap: 10419: VDEV Create 4a:3f:8c:79:57:9e [ 40.828001] wlan: [5539:E:CMN_MLME] mlme_vdev_ext_obj_create: 1389: VDEV MLME obj is creation [ 40.836229] wlan: [5539:I:ANY] wlan_vap_create: 1594: enter. devhandle=0xffffffc013a80880, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 40.836229] [ 40.845079] wlan: [5539:I:ANY] ol_ath_vap_set_param: 1121: Setting SGI value: 1 [ 40.858188] wlan: [5539:I:ANY] ol_ath_vap_set_param: 2149: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1 [ 40.864898] wlan: [5539:I:ANY] ol_ath_vap_set_param: 2159: he_bf_cap=0x7b [ 40.878418] wlan: [5539:I:ANY] ol_ath_vap_set_param: 2174: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 40.885518] wlan: [5539:I:ANY] MBO Initialized [ 40.899496] wlan: [5539:I:ANY] OCE Initialized [ 40.903687] wlan: [5539:I:ANY] osif_nss_ol_vap_create: 1268: NSS wifi offload VAP create IF 35 nss_id -1 [ 40.908176] wlan: [5539:I:ANY] NSS radio_if 32 [ 40.917824] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1020: VDEV configuration success: 0 [ 40.922097] wlan: [5539:I:ANY] osif_nss_ol_vap_create: 1376: vap create ffffffc016dac880 : if_num 35 [ 40.930466] wlan: [5539:I:ANY] wlan_vap_create: 1627: exit [ 40.939765] wlan: [5539:E:ANY] Smart Antenna is not supported [ 40.945352] wlan: [5539:E:ANY] Smart Antenna is not supported [ 40.951003] wlan: [5539:I:ANY] osif_create_vap_complete: 10617: TX Checksum:1|SG:1|TSO:1|LRO:0 [ 40.956693] wlan: [5539:I:ANY] WLAN-NSS: VAP NSS ops initialized [ 40.966441] wlan: [5539:I:ANY] VAP device ath02 created osifp: (ffffffc016dac880) os_if: (ffffffc00e2b0000) cfg80211tool ath02 mode 11GHE40 cfg80211tool ath02 mode 11GHE40 cfg80211tool ath02 channel 0 cfg80211tool ath02 hide_ssid 1 cfg80211tool ath02 dynamicbeacon 0 cfg80211tool ath02 disablecoext 1 cfg80211tool ath02 wds 1 cfg80211tool ath02 backhaul 0 cfg80211tool ath02 uapsd 1 cfg80211tool ath02 vap_ind 0 cfg80211tool ath02 extap 0 cfg80211tool ath02 stafwd 0 [ 41.805440] wlan: [5699:I:ANY] osif_nss_vdev_set_cfg: 1999: setting hifi mode 5 target type 0 [ 41.805494] wlan: [5699:I:ANY] osif_nss_vdev_set_cfg: 2003: Mcast command 5 [ 41.817012] wlan: [5701:I:ANY] osif_nss_vdev_set_cfg: 1999: setting hifi mode 5 target type 0 [ 41.819723] wlan: [5701:I:ANY] osif_nss_vdev_set_cfg: 2003: Mcast command 5 cfg80211tool ath02 maxsta 128 [ 41.901255] wlan: [5709:I:ANY] ieee80211_ucfg_setparam: 1453: Setting Max Stations:128 cfg80211tool ath02 blockdfschan 1 cfg80211tool ath02 rrm 1 cfg80211tool ath02 athnewind 1 cfg80211tool ath02 son 1 cfg80211tool ath02 rept_spl 0 cfg80211tool ath02 ap_bridge 1 [ 42.540943] wlan: [877:I:ANY] wlan_cfg80211_do_acs: 3474: vap-2(ath02):ACS Params [ 42.540982] wlan: [877:I:ANY] wlan_cfg80211_do_acs: 3477: ht_enabled:1|ht40_enabled:0|vht_enabled:1|hw_mode:29|chwidth:20| [ 42.547488] wlan: [877:I:ANY] ieee80211_autoselect_infra_bss_channel: 4059: ACS started: vap:0xffffffc00e2b0000 cfg80211tool ath02 11ngvhtintop 1 [ 42.624089] ieee80211_acs_find_best_11ng_centerchan: acs_11ngbestchan = 12 [ 42.624125] 2.4G Best Channel Selected 9 rssi 0 nf -107 [ 42.630014] wlan: [3012:I:ANY] vap-0(ath0): ACS result PCH 9, SCH 13, hw_mode 1 chwidth 40, vht_seg0 11, vht_seg1 0 [ 42.635319] wlan: [3012:I:ANY] vap-1(ath01): ACS result PCH 9, SCH 13, hw_mode 1 chwidth 40, vht_seg0 11, vht_seg1 0 [ 42.645985] wlan: [3012:I:ANY] vap-2(ath02): ACS result PCH 9, SCH 13, hw_mode 1 chwidth 40, vht_seg0 11, vht_seg1 0 [ 42.656620] wlan: [3012:I:ANY] ieee80211_acs_scan_evhandler: 3796: lock held duration: 32(ms) qcawifi qcawificfg80211: enable radio wifi0 [ 42.712421] wlan: [877:I:ANY] DES SSID SET=kalaverkko_mesh [ 42.712460] wlan: [877:I:ANY] wlan_cfg80211_chan_to_phymode: 1235: wlan_cfg80211_chan_to_phymode: band:0 width: 2 channel_cfreq: 2452 center_freq1: 2462 chandef.center_freq2: 0 flags: 0 [ 42.739454] wlan: [0:I:CMN_MLME] vdev[0] ieee chan:9 [ 42.739799] wlan: [0:E:ANY] Smart Antenna is not supported [ 42.743512] wlan: [0:I:ANY] vdev[0]: Mgt Rate:1000(kbps) [ 42.748836] wlan: [0:I:ANY] vdev[0]: Mgt Rate:1000(kbps) update_ini_file cfg80211_config=1 update_ini_file qwrap_enable=0 update_ini_file nss_wifi_olcfg=3 update_ini_file rx_hash=0 update_ini_file allow_mon_vaps_in_sr= cfg80211tool wifi0 blockdfslist 1[ 42.914562] wlan: [877:I:ANY] DES SSID SET=kalaverkko_Guest [ 42.914788] wlan: [877:I:ANY] wlan_cfg80211_set_phymode: 1211: desired hw mode: 26 [ 42.920216] wlan: [877:I:ANY] ieee80211_ucfg_set_freq_internal: 530: [ 42.920216] Channel is configured already!! [ 42.928582] wlan: [0:I:CMN_MLME] vdev[1] ieee chan:9 [ 42.938779] wlan: [0:I:ANY] vdev[1]: Mgt Rate:1000(kbps) [ 42.943557] wlan: [0:I:ANY] vdev[1]: Mgt Rate:1000(kbps) cfg80211tool wifi0 setCountry DE [ 43.002046] wlan: [877:I:ANY] DES SSID SET=zEQQkm3a2VA5zeB5 [ 43.002079] wlan: [877:I:ANY] wlan_cfg80211_set_phymode: 1211: desired hw mode: 26 [ 43.006638] wlan: [877:I:ANY] ieee80211_ucfg_set_freq_internal: 530: [ 43.006638] Channel is configured already!! [ 43.019392] wlan: [0:I:CMN_MLME] vdev[2] ieee chan:9 [ 43.025111] wlan: [0:I:ANY] vdev[2]: Mgt Rate:1000(kbps) [ 43.029901] wlan: [0:I:ANY] vdev[2]: Mgt Rate:1000(kbps) [ 43.043727] wlan: [5864:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 4 [ 43.044258] wlan: [5864:I:ANY] wlan_scan_update_channel_list: 1090: num_chan: 4 [ 43.049895] wlan: [5864:I:ANY] number of channels: 2G = 0 5G = 4 [ 43.057590] wlan: [5864:I:ANY] wlan_cfg80211_set_country: 6059: wlan_cfg80211_set_country: Country: DE ret: 0 [ 43.064110] wlan: [2763:I:ANY] ol_acfg_handle_wifi_ioctl: 417: ol_acfg_handle_wifi_ioctl: req->cmd=75 not valid for radio interface, it's for VAP cfg80211tool wifi0 bsta_fixed_idmask 255 cfg80211tool wifi0 set_bcnburst 0 cfg80211tool wifi0 sIgmpDscpOvrid 1 cfg80211tool wifi0 sIgmpDscpTidMap 6 cfg80211tool wifi0 enable_ol_stats 1 cfg80211tool wifi0 setHwaddr 40:3F:8C:79:57:9F [ 43.321770] wlan: [5887:I:ANY] wlan_cfg80211_set_hwaddr: 6132: wlan_cfg80211_set_hwaddr :40:3f:8c:79:57:9f ret: 0 cfg80211tool wifi0 txbf_snd_int 100 [ 43.370741] wlan: [5891:I:ANY] ol_ath_set_config_param: 1577: set TXBF_SND_PERIOD: value 100 wmi_status 0 cfg80211tool wifi0 obss_rssi_th 35 cfg80211tool wifi0 obss_rxrssi_th 35 cfg80211tool wifi0 dbdc_enable 0 [ 43.504604] wlan: [0:I:ANY] dp_lag_soc_enable: 91: pdev(ffffffc01516ac08) Enabling DBDC Repeater 0 [ 43.504690] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed [ 43.512484] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed [ 43.520809] wlan: [0:E:NSS] [nss-wifili]: NSS Wifili DBDC Repeater enable message passed cfg80211tool wifi0 no_vlan 1 cfg80211tool wifi0 discon_time 10 [ 43.630203] wlan: [0:I:ANY] ol_ath_set_config_param: 2328: Disconnect_timeout value: 10 cfg80211tool wifi0 reconfig_time 60 [ 43.677483] wlan: [0:I:ANY] ol_ath_set_config_param: 2334: Reconfiguration_timeout value:60 cfg80211tool wifi0 fc_buf0_max 8192 cfg80211tool wifi0 fc_buf1_max 8192 cfg80211tool wifi0 fc_buf2_max 8192 cfg80211tool wifi0 fc_buf3_max 8192 cfg80211tool wifi0 get_rxchainmask number of vifs: ath1 ath12 wlanconfig ath1 create wlandev wifi0 wlanmode ap -cfg80211 [ 44.090546] wlan: [6002:I:ANY] wlan_cfg80211_add_virtual_intf: 325: proprietary mode 6 for interface: ath1 : clone params: 0x00000001 [ 44.090623] wlan: [6002:I:ANY] osifp_create_wlan_vap: 10419: VDEV Create 40:3f:8c:79:57:9f [ 44.101704] wlan: [6002:E:CMN_MLME] mlme_vdev_ext_obj_create: 1389: VDEV MLME obj is creation [ 44.109892] wlan: [6002:I:ANY] wlan_vap_create: 1594: enter. devhandle=0xffffffc013a40880, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 44.109892] [ 44.118817] wlan: [6002:I:ANY] ol_ath_vap_set_param: 1121: Setting SGI value: 1 [ 44.131575] wlan: [6002:I:ANY] ol_ath_vap_set_param: 2149: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1 [ 44.138593] wlan: [6002:I:ANY] ol_ath_vap_set_param: 2159: he_bf_cap=0x7b [ 44.152110] wlan: [6002:I:ANY] ol_ath_vap_set_param: 2174: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 44.159066] wlan: [6002:I:ANY] MBO Initialized [ 44.173058] wlan: [6002:I:ANY] OCE Initialized [ 44.177409] wlan: [6002:I:ANY] osif_nss_ol_vap_create: 1268: NSS wifi offload VAP create IF 36 nss_id -1 [ 44.181825] wlan: [6002:I:ANY] NSS radio_if 31 [ 44.191559] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1020: VDEV configuration success: 0 [ 44.195828] wlan: [6002:I:ANY] osif_nss_ol_vap_create: 1376: vap create ffffffc00e86e880 : if_num 36 [ 44.204067] wlan: [6002:I:ANY] wlan_vap_create: 1627: exit [ 44.213412] wlan: [6002:E:ANY] Smart Antenna is not supported [ 44.218996] wlan: [6002:E:ANY] Smart Antenna is not supported [ 44.224635] wlan: [6002:I:ANY] osif_create_vap_complete: 10617: TX Checksum:1|SG:1|TSO:1|LRO:0 [ 44.230344] wlan: [6002:I:ANY] WLAN-NSS: VAP NSS ops initialized [ 44.240252] wlan: [6002:I:ANY] VAP device ath1 created osifp: (ffffffc00e86e880) os_if: (ffffffc00e1f8000) cfg80211tool ath1 mode 11AHE80 cfg80211tool ath1 mode 11AHE80 cfg80211tool ath1 channel 0 cfg80211tool ath1 hide_ssid 0 cfg80211tool ath1 nrshareflag 7 cfg80211tool ath1 disablecoext 1 cfg80211tool ath1 wds 1 cfg80211tool ath1 backhaul 0 cfg80211tool ath1 en_sae_pwid 1 cfg80211tool ath1 en_sae_pwid 1 cfg80211tool ath1 uapsd 1 cfg80211tool ath1 vap_ind 0 cfg80211tool ath1 extap 0 cfg80211tool ath1 amsdu 2 cfg80211tool ath1 stafwd 0 cfg80211tool ath1 maccmd_sec 2 cfg80211tool ath1 maxsta 128 [ 45.457250] wlan: [6079:I:ANY] ieee80211_ucfg_setparam: 1453: Setting Max Stations:128 cfg80211tool ath1 blockdfschan 1 cfg80211tool ath1 rrm 1 cfg80211tool ath1 vhtsubfee 1 cfg80211tool ath1 vhtmubfee 1 cfg80211tool ath1 vhtsubfer 1 cfg80211tool ath1 vhtmubfer 1 cfg80211tool ath1 he_subfee 1 [ 45.970420] wlan: [6104:I:ANY] wlan_set_param: 2953: HE SU BFEE already set with this value =1 cfg80211tool ath1 he_subfer 1 [ 46.061429] wlan: [6107:I:ANY] wlan_set_param: 2972: HE SU BFER already set with this value =1 cfg80211tool ath1 he_mubfee 1 [ 46.143852] wlan: [6110:I:ANY] ieee80211_ucfg_setparam: 4918: HE MU BFEE only supported in STA mode cfg80211tool ath1 he_mubfer 1 [ 46.225640] wlan: [6115:I:ANY] wlan_set_param: 3018: HE MU BFER already set with this value =1 cfg80211tool ath1 athnewind 1 iwpriv ath1 he_ulmumimo 0 [ 46.335875] wlan: [6131:I:ANY] ol_ath_vap_set_param: 2149: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:0 [ 46.335925] wlan: [6131:I:ANY] ol_ath_vap_set_param: 2159: he_bf_cap=0x3b iwpriv ath1 he_ulofdma 0 [ 46.360227] wlan: [6135:I:ANY] ol_ath_vap_set_param: 2149: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:0|ul_mumimo:0 [ 46.360277] wlan: [6135:I:ANY] ol_ath_vap_set_param: 2159: he_bf_cap=0x1b cfg80211tool ath1 ap_bridge 1 [ 46.662466] device ath1 entered promiscuous mode [ 46.662578] br-lan: port 5(ath1) entered forwarding state [ 46.666214] br-lan: port 5(ath1) entered forwarding state [ 46.672416] wlan: [877:I:ANY] wlan_cfg80211_do_acs: 3474: vap-3(ath1):ACS Params [ 46.677095] wlan: [877:I:ANY] wlan_cfg80211_do_acs: 3477: ht_enabled:1|ht40_enabled:0|vht_enabled:1|hw_mode:30|chwidth:20| [ 46.684555] wlan: [877:I:ANY] ieee80211_autoselect_infra_bss_channel: 4059: ACS started: vap:0xffffffc00e1f8000 wlanconfig ath12 create wlandev wifi0 wlanmode ap -cfg80211 [ 46.901611] wlan: [6279:I:ANY] wlan_cfg80211_add_virtual_intf: 325: proprietary mode 6 for interface: ath12 : clone params: 0x00000001 [ 46.901693] wlan: [6279:I:ANY] osifp_create_wlan_vap: 10419: VDEV Create 46:3f:8c:79:57:9f [ 46.912975] wlan: [6279:E:CMN_MLME] mlme_vdev_ext_obj_create: 1389: VDEV MLME obj is creation [ 46.920963] wlan: [6279:I:ANY] wlan_vap_create: 1594: enter. devhandle=0xffffffc013a40880, opmode=IEEE80211_M_HOSTAP, flags=0x1 [ 46.920963] [ 46.929782] wlan: [6279:I:ANY] ol_ath_vap_set_param: 1121: Setting SGI value: 1 [ 46.942673] wlan: [6279:I:ANY] ol_ath_vap_set_param: 2149: VDEV params:HE su_bfee:1|su_bfer:1|mu_bfee:0|mu_bfer:1|dl_muofdma:1|ul_muofdma:1|ul_mumimo:1 [ 46.949755] wlan: [6279:I:ANY] ol_ath_vap_set_param: 2159: he_bf_cap=0x7b [ 46.963265] wlan: [6279:I:ANY] ol_ath_vap_set_param: 2174: VDEV params:AC/VHT sounding mode:HE|SU/MU sounding mode:SU|Trig/Non-Trig sounding mode:Non-Trigged [ 46.970273] wlan: [6279:I:ANY] MBO Initialized [ 46.984306] wlan: [6279:I:ANY] OCE Initialized [ 46.988556] wlan: [6279:I:ANY] osif_nss_ol_vap_create: 1268: NSS wifi offload VAP create IF 37 nss_id -1 [ 46.992977] wlan: [6279:I:ANY] NSS radio_if 31 [ 47.002656] wlan: [0:I:ANY] osif_nss_vdev_cfg_callback: 1020: VDEV configuration success: 0 [ 47.006987] wlan: [6279:I:ANY] osif_nss_ol_vap_create: 1376: vap create ffffffc00e210880 : if_num 37 [ 47.015284] wlan: [6279:I:ANY] wlan_vap_create: 1627: exit [ 47.024580] wlan: [6279:E:ANY] Smart Antenna is not supported [ 47.030129] wlan: [6279:E:ANY] Smart Antenna is not supported [ 47.035790] wlan: [6279:I:ANY] osif_create_vap_complete: 10617: TX Checksum:1|SG:1|TSO:1|LRO:0 [ 47.041497] wlan: [6279:I:ANY] WLAN-NSS: VAP NSS ops initialized [ 47.051809] wlan: [6279:I:ANY] VAP device ath12 created osifp: (ffffffc00e210880) os_if: (ffffffc00e368000) [ 47.056497] wlan: [6285:I:ANY] osif_nss_vdev_set_cfg: 1999: setting hifi mode 5 target type 0 [ 47.066599] wlan: [6285:I:ANY] osif_nss_vdev_set_cfg: 2003: Mcast command 5 cfg80211tool ath12 mode 11AHE80 [ 47.081784] wlan: [6291:I:ANY] osif_nss_vdev_set_cfg: 1999: setting hifi mode 5 target type 0 [ 47.084334] wlan: [6291:I:ANY] osif_nss_vdev_set_cfg: 2003: Mcast command 5 [ 47.095438] wlan: [6294:I:ANY] osif_nss_vdev_set_cfg: 1999: setting hifi mode 5 target type 0 [ 47.102453] wlan: [6294:I:ANY] osif_nss_vdev_set_cfg: 2003: Mcast command 5 cfg80211tool ath12 mode 11AHE80 cfg80211tool ath12 channel 0 cfg80211tool ath12 hide_ssid 1 cfg80211tool ath12 dynamicbeacon 0 cfg80211tool ath12 disablecoext 1 cfg80211tool ath12 wds 1 cfg80211tool ath12 backhaul 0 cfg80211tool ath12 uapsd 1 cfg80211tool ath12 vap_ind 0 cfg80211tool ath12 extap 0 cfg80211tool ath12 stafwd 0 cfg80211tool ath12 maxsta 128 [ 47.926198] wlan: [3012:I:ANY] vap-3(ath1): ACS result PCH 48, SCH 36, hw_mode 2 chwidth 80, vht_seg0 42, vht_seg1 0 [ 47.926263] wlan: [3012:I:ANY] ieee80211_acs_scan_evhandler: 3796: lock held duration: 0(ms) [ 47.943025] wlan: [6371:I:ANY] ieee80211_ucfg_setparam: 1453: Setting Max Stations:128 cfg80211tool ath12 blockdfschan 1 [ 48.009231] wlan: [877:I:ANY] DES SSID SET=kalaverkko_mesh [ 48.009265] wlan: [877:I:ANY] wlan_cfg80211_set_phymode: 1211: desired hw mode: 30 cfg80211tool ath12 rrm 1 [ 48.038001] wlan: [0:I:CMN_MLME] vdev[3] ieee chan:48 [ 48.038325] wlan: [0:E:ANY] Smart Antenna is not supported [ 48.042072] wlan: [0:I:ANY] vdev[3]: Mgt Rate:6000(kbps) [ 48.047476] wlan: [0:I:ANY] vdev[3]: Mgt Rate:6000(kbps) cfg80211tool ath12 athnewind 1 cfg80211tool ath12 son 1 cfg80211tool ath12 rept_spl 0 cfg80211tool ath12 ap_bridge 1 [ 48.579618] wlan: [877:I:ANY] wlan_cfg80211_do_acs: 3474: vap-4(ath12):ACS Params [ 48.579658] wlan: [877:I:ANY] wlan_cfg80211_do_acs: 3477: ht_enabled:1|ht40_enabled:0|vht_enabled:1|hw_mode:30|chwidth:20| [ 48.586344] wlan_cfg80211_do_acs: acs_report_channel [ 48.597256] wlan: [877:I:ANY] vap-4(ath12): ACS result PCH 48, SCH 36, hw_mode 2 chwidth 80, vht_seg0 42, vht_seg1 0 qcawifi qcawificfg80211: enable radio wifi2 [ 48.681485] wlan: [877:I:ANY] DES SSID SET=zEQQkm3a2VA5zeB5 [ 48.681616] wlan: [877:I:ANY] wlan_cfg80211_set_phymode: 1211: desired hw mode: 30 [ 48.686240] wlan: [877:I:ANY] ieee80211_ucfg_set_freq_internal: 530: [ 48.686240] Channel is configured already!! [ 48.693977] wlan: [0:I:dfs] WLAN_DEBUG_DFS_ALWAYS : dfs_set_current_channel: 807: dfs_curchan already updated [ 48.704835] wlan: [0:I:CMN_MLME] vdev[4] ieee chan:48 [ 48.714591] wlan: [0:I:ANY] vdev[4]: Mgt Rate:6000(kbps) [ 48.719306] wlan: [0:I:ANY] vdev[4]: Mgt Rate:6000(kbps) update_ini_file cfg80211_config=1 update_ini_file qwrap_enable=0 update_ini_file nss_wifi_olcfg=3 update_ini_file rx_hash=0 update_ini_file allow_mon_vaps_in_sr= INFO:QDSS_tracing not applicable for ap-ac04 [ 49.801885] wlan: [6650:I:ANY] osif_nss_vdev_set_cfg: 1999: setting hifi mode 5 target type 0 [ 49.801925] wlan: [6650:I:ANY] osif_nss_vdev_set_cfg: 2003: Mcast command 5 [ 49.811373] wlan: [6651:I:ANY] osif_nss_vdev_set_cfg: 1999: setting hifi mode 5 target type 0 [ 49.816191] wlan: [6651:I:ANY] osif_nss_vdev_set_cfg: 2003: Mcast command 5 [ 49.826797] wlan: [6652:I:ANY] osif_nss_vdev_set_cfg: 1999: setting hifi mode 5 target type 0 [ 49.831618] wlan: [6652:I:ANY] osif_nss_vdev_set_cfg: 2003: Mcast command 5 whc (repacd): do __repacd_add_vlan_interfaces network:lan vlan id:1 backhual_iface:wifi /lib/sync-server/scripts/probe:408: Warning: I have no IP whc (repacd): 2g interfaces:ath02, 5g interfaces:ath12 whc (repacd): plc interfaces: interface5g:ath12 whc (repacd): ath12.1 does not exist, add it. [ 50.475772] device ath12.1 entered promiscuous mode [ 50.482813] device ath12 entered promiscuous mode [ 50.483605] br-lan: port 6(ath12.1) entered forwarding state [ 50.486556] br-lan: port 6(ath12.1) entered forwarding state interface2g:ath02 whc (repacd): ath02.1 does not exist, add it. [ 50.566594] device ath02.1 entered promiscuous mode [ 50.573133] device ath02 entered promiscuous mode [ 50.573474] br-lan: port 7(ath02.1) entered forwarding state [ 50.576881] br-lan: port 7(ath02.1) entered forwarding state whc (repacd): do __repacd_del_vlan_interfaces network:lan vlan id:1 backhual_iface:plc whc (repacd): 2g interfaces:, 5g interfaces: whc (repacd): plc interfaces: whc (repacd): set wifi done flag whc (repacd): unlock whc_wifi_config_lock whc (repacd): get whc_wifi_config_lock whc (repacd): clear wifi_set_done flag whc (repacd): starting WHC auto-configuration whc (repacd): Managed network: lan whc (repacd): Device type: RE whc (repacd): Sysmode: AP whc (repacd): the guest network version of the device is latest, we do nothing(uci_revert_state wifi guest enable) whc (repacd): Using SON mode for NonCAP whc (repacd): __repacd_restart_dependencies: No changes; not restarting network stack... whc (repacd): do __repacd_add_vlan_interfaces network:lan vlan id:1 backhual_iface:wifi whc (repacd): 2g interfaces:ath02, 5g interfaces:ath12 whc (repacd): plc interfaces: interface5g:ath12 whc (repacd): ath12.1 already existed, do nothing. interface2g:ath02 whc (repacd): ath02.1 already existed, do nothing. whc (repacd): do __repacd_del_vlan_interfaces network:lan vlan id:1 backhual_iface:plc whc (repacd): 2g interfaces:, 5g interfaces: whc (repacd): plc interfaces: whc (repacd): set wifi done flag whc (repacd): unlock whc_wifi_config_lock [ 52.936892] work mode change to :RE [ 52.936892] parental-control_avira: stop the avira homecare [aviraSentinelFull]: stop IS_AVIRA_SENTINEL_FULL_RESTART: 0 [aviraSentinelLite]: stop IS_AVIRA_SENTINEL_LITE_RESTART: 0 [ 3257(lan)] [smartip_ibus_handle_wifi_event 2283] smartipd handle wifi event:10 [ 3257(lan)] [smartip_ibus_handle_wifi_event 2359] AP -> RE ### aviraserviceselector stop ### [aviraSentinelFull]: stop IS_AVIRA_SENTINEL_FULL_RESTART: 0 execute save tmp config /lib/sync-server/scripts/probe:408: Warning: I have no IP homecare upgrade pc_insights script running saveconfig() begin fileToXml App QoS is NOT enable [aviraSentinelLite]: stop IS_AVIRA_SENTINEL_LITE_RESTART: 0 saveconfig() end [ 53.757051] wlan: [7512:I:ANY] osif_nss_vdev_set_cfg: 1999: setting hifi mode 5 target type 0 [ 53.757095] wlan: [7512:I:ANY] osif_nss_vdev_set_cfg: 2003: Mcast command 5 [ 53.766880] wlan: [7519:I:ANY] osif_nss_vdev_set_cfg: 1999: setting hifi mode 5 target type 0 [ 53.771336] wlan: [7519:I:ANY] osif_nss_vdev_set_cfg: 2003: Mcast command 5 [ 53.785872] wlan: [7523:I:ANY] osif_nss_vdev_set_cfg: 1999: setting hifi mode 5 target type 0 [ 53.786786] wlan: [7523:I:ANY] osif_nss_vdev_set_cfg: 2003: Mcast command 5 paid mode but not profile client(or free and hc_upg_support=yes), stop classifier ################### app-classifier stop ################### [PCTL_DEBUG]: fw_del_web_filter_all start [hotplug]: change to role RE, app-classifier stop ################### app-classifier stop ################### [hotplug]: change to role RE, app-dpi stop =============== app-dpi stop =============== cwmp: stop cwmp ========= MODE: cloud_awn_update begin ========== mode: RE Ipv6 Firewall config trigger stop! qos_v2 stop tc qdisc add dev br-wan root handle 1: htb default 101 tc class add dev br-wan parent 1: classid 1:1 htb rate 1024000kbit ceil 1024000kbit burst 1281600 cburst 1281600 quantum 1500 tc class add dev br-wan parent 1:1 classid 1:101 htb rate 1024000kbit ceil 1024000kbit burst 1281600 cburst 1281600 quantum 1500 prio 3 tc qdisc add dev br-wan parent 1:101 handle 101: sfq perturb 10 tc qdisc add dev br-lan root handle 2: htb default 202 tc class add dev br-lan parent 2: classid 2:2 htb rate 1024000kbit ceil 1024000kbit burst 1281600 cburst 1281600 quantum 1500 tc class add dev br-lan parent 2:2 classid 2:202 htb rate 1024000kbit ceil 1024000kbit burst 1281600 cburst 1281600 quantum 1500 prio 3 tc qdisc add dev br-lan parent 2:202 handle 202: sfq perturb 10 --------->exiting qos [ 55.832769] wlan: [8023:I:ANY] ieee80211_ioctl_siwscan: 3379: preempt_scan xxxx [ 55.835621] wlan: [8024:I:ANY] ieee80211_ioctl_siwscan: 3379: preempt_scan xxxx [awnd_get_scan_result:1240]: unable to get scan result:ifname:ath02, ret:-1 /lib/sync-server/scripts/probe:408: Warning: I have no IP [ 69.412972] wlan: [8671:I:ANY] ieee80211_ioctl_siwscan: 3379: preempt_scan xxxx [ 69.413067] wlan: [8670:I:ANY] ieee80211_ioctl_siwscan: 3379: preempt_scan xxxx

''Format: Log Type - Time(microsec) - Message - Optional Info Log Type: B - Since Boot(Power On Reset), D - Delta, S - Statistic S - QC_IMAGE_VERSION_STRING=BOOT.BF.3.3.1-00156 S - IMAGE_VARIANT_STRING=HAACANAZA S - OEM_IMAGE_VERSION_STRING=CRM S - Boot Config, 0x000002e5 B - 201 - PBL, Start B - 2736 - bootable_media_detect_entry, Start B - 3444 - bootable_media_detect_success, Start B - 3448 - elf_loader_entry, Start B - 6116 - auth_hash_seg_entry, Start B - 6358 - auth_hash_seg_exit, Start B - 68393 - elf_segs_hash_verify_entry, Start B - 131218 - PBL, End B - 223260 - SBL1, Start B - 304603 - GCC [RstStat:0x10, RstDbg:0x600000] WDog Stat : 0x4 B - 314729 - pm_device_init, Start B - 503738 - PM_SET_VAL:Skip D - 186934 - pm_device_init, Delta B - 506147 - pm_driver_init, Start D - 5368 - pm_driver_init, Delta B - 512522 - clock_init, Start D - 2135 - clock_init, Delta B - 516487 - boot_flash_init, Start D - 13237 - boot_flash_init, Delta B - 533475 - boot_config_data_table_init, Start D - 3202 - boot_config_data_table_init, Delta - (575 Bytes) B - 540887 - Boot Setting : 0x00000600 B - 544913 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:16 B - 551836 - sbl1_ddr_set_params, Start B - 555679 - CPR configuration: 0x300 B - 559065 - cpr_init, Start B - 561932 - Rail:0 Mode: 5 Voltage: 800000 B - 567086 - CL CPR settled at 752000mV B - 569923 - Rail:1 Mode: 5 Voltage: 880000 B - 574101 - Rail:1 Mode: 7 Voltage: 888000 D - 16470 - cpr_init, Delta B - 580994 - Pre_DDR_clock_init, Start B - 585020 - Pre_DDR_clock_init, End B - 588406 - DDR Type : PCDDR3 B - 594018 - do ddr sanity test, Start D - 1067 - do ddr sanity test, Delta B - 598837 - DDR: Start of HAL DDR Boot Training B - 603595 - DDR: End of HAL DDR Boot Training B - 609268 - DDR: Checksum to be stored on flash is 1608444581 B - 619668 - Image Load, Start D - 224297 - QSEE Image Loaded, Delta - (1374392 Bytes) B - 844057 - Image Load, Start D - 30 - SEC Image Loaded, Delta - (0 Bytes) B - 851743 - Image Load, Start D - 10705 - DEVCFG Image Loaded, Delta - (26008 Bytes) B - 862540 - Image Load, Start D - 25315 - RPM Image Loaded, Delta - (106428 Bytes) B - 887916 - Image Load, Start D - 109098 - APPSBL Image Loaded, Delta - (672308 Bytes) B - 997167 - QSEE Execution, Start D - 61 - QSEE Execution, Delta B - 1002962 - USB D+ check, Start D - 0 - USB D+ check, Delta B - 1009336 - SBL1, End D - 788394 - SBL1, Delta S - Flash Throughput, 6752 KB/s (2180383 Bytes, 322896 us) S - DDR Frequency, 466 MHz S - Core 0 Frequency, 800 MHz U-Boot 2016.01 (May 11 2020 - 18:03:48 -0700) DRAM: smem ram ptable found: ver: 1 len: 4 512 MiB NAND: ONFI device found ID = 9500a1ef Vendor = ef Device = a1 128 MiB MMC: sdhci: Node Not found, skipping initialization PCI1 is not defined in the device tree In: serial@78B3000 Out: serial@78B3000 Err: serial@78B3000 machid: 8010010 MMC Device 0 not found eth0 MAC Address from ART is not valid eth1 MAC Address from ART is not valid eth2 MAC Address from ART is not valid eth3 MAC Address from ART is not valid eth4 MAC Address from ART is not valid eth5 MAC Address from ART is not valid ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=0", size 9 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 72, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 11/6, WL threshold: 4096, image sequence number: 1864824124 ubi0: available PEBs: 0, total reserved PEBs: 72, PEBs reserved for bad PEB handling: 20 Find no boot alter flag! Enter magic string to stop autoboot in 1 seconds Unmounting UBIFS volume ubi_factory_data! ubi0: detaching mtd1 ubi0: mtd1 is detached ubi0: attaching mtd1 ubi0: scanning is finished ubi0: attached mtd1 (name "mtd=0", size 42 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 336, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 12/9, WL threshold: 4096, image sequence number: 898308538 ubi0: available PEBs: 0, total reserved PEBs: 336, PEBs reserved for bad PEB handling: 20 Read 0 bytes from volume kernel to 44000000 No size specified -> Using max size (5586944) ## Loading kernel from FIT Image at 44000000 ... Using 'config@ac04' configuration Trying 'kernel-1' kernel subimage Description: ARM64 OpenWrt Linux-6.12.93 Type: Kernel Image Compression: gzip compressed Data Start: 0x440000e8 Data Size: 5533770 Bytes = 5.3 MiB Architecture: AArch64 OS: Linux Load Address: 0x41000000 Entry Point: 0x41000000 Hash algo: crc32 Hash value: 76449891 Hash algo: sha1 Hash value: 4c47df0b7a1ce5b34d55ae4402df82b8aed46990 Verifying Hash Integrity ... crc32+ sha1+ OK ## Loading fdt from FIT Image at 44000000 ... Using 'config@ac04' configuration Trying 'fdt-1' fdt subimage Description: ARM64 OpenWrt tplink_deco-x60-v2 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x44547278 Data Size: 43559 Bytes = 42.5 KiB Architecture: AArch64 Hash algo: crc32 Hash value: 0b79cd5c Hash algo: sha1 Hash value: df9e7b58654afc29c118130b2fd46a91632f6212 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x44547278 Uncompressing Kernel Image ... OK Loading Device Tree to 4a3f2000, end 4a3ffa26 ... OK Could not find PCI in device tree Using machid 0x8010010 from environment Starting kernel ... Jumping to AARCH64 kernel via monitor [ 0.000000] Booting Linux on physical CPU 0x0000000000 [0x410fd034] [ 0.000000] Linux version 6.12.93 (builder@buildhost) (aarch64-openwrt-linux-musl-gcc (OpenWrt GCC 14.3.0 r34912-88934ad4c8) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sat Jul 4 09:02:24 2026 [ 0.000000] Machine model: TP-Link Deco X60 v2 [ 0.000000] OF: reserved mem: 0x0000000040000000..0x0000000040ffffff (16384 KiB) nomap non-reusable nss@40000000 [ 0.000000] OF: reserved mem: 0x000000004a400000..0x000000004a4fffff (1024 KiB) nomap non-reusable tzapp@4a400000 [ 0.000000] OF: reserved mem: 0x000000004a600000..0x000000004a9fffff (4096 KiB) nomap non-reusable bootloader@4a600000 [ 0.000000] OF: reserved mem: 0x000000004aa00000..0x000000004aafffff (1024 KiB) nomap non-reusable sbl@4aa00000 [ 0.000000] OF: reserved mem: 0x000000004ab00000..0x000000004abfffff (1024 KiB) nomap non-reusable smem@4ab00000 [ 0.000000] OF: reserved mem: 0x000000004ac00000..0x000000004affffff (4096 KiB) nomap non-reusable memory@4ac00000 [ 0.000000] OF: reserved mem: 0x000000004b000000..0x000000004e6fffff (56320 KiB) nomap non-reusable wcnss@4b000000 [ 0.000000] OF: reserved mem: 0x000000004e700000..0x000000004e7fffff (1024 KiB) nomap non-reusable q6_etr_dump@50f00000 [ 0.000000] OF: reserved mem: 0x000000004e800000..0x000000004e8fffff (1024 KiB) nomap non-reusable m3_dump@51000000 [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] DMA32 empty [ 0.000000] Normal empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000040000000-0x0000000040ffffff] [ 0.000000] node 0: [mem 0x0000000041000000-0x000000004a3fffff] [ 0.000000] node 0: [mem 0x000000004a400000-0x000000004a4fffff] [ 0.000000] node 0: [mem 0x000000004a500000-0x000000004a5fffff] [ 0.000000] node 0: [mem 0x000000004a600000-0x000000004e8fffff] [ 0.000000] node 0: [mem 0x000000004e900000-0x000000005fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000005fffffff] [ 0.000000] psci: probing for conduit method from DT. [ 0.000000] psci: PSCIv1.0 detected in firmware. [ 0.000000] psci: Using standard PSCI v0.2 function IDs [ 0.000000] psci: MIGRATE_INFO_TYPE not supported. [ 0.000000] psci: SMC Calling Convention v1.0 [ 0.000000] psci: OSI mode supported. [ 0.000000] psci: [Firmware Bug]: failed to set PC mode: -1 [ 0.000000] percpu: Embedded 20 pages/cpu s43224 r8192 d30504 u81920 [ 0.000000] Detected VIPT I-cache on CPU0 [ 0.000000] alternatives: applying boot alternatives [ 0.000000] Kernel command line: ubi.mtd=rootfs root=mtd:ubi_rootfs rootfstype=squashfs rootwait root=/dev/ubiblock0_1 swiotlb=1 coherent_pool=2M [ 0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes, linear) [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 131072 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] software IO TLB: area num 4. [ 0.000000] software IO TLB: SWIOTLB bounce buffer size roundup to 1MB [ 0.000000] software IO TLB: mapped [mem 0x000000005f4c0000-0x000000005f5c0000] (1MB) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0 [ 0.000000] Root IRQ handler: gic_handle_irq [ 0.000000] GICv2m: range[mem 0x0b00a000-0x0b00affc], SPI[448:479] [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] arch_timer: cp15 and mmio timer(s) running at 19.20MHz (virt/virt). [ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x46d987e47, max_idle_ns: 440795202767 ns [ 0.000001] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 4398046511078ns [ 0.000129] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000) [ 0.000143] pid_max: default: 32768 minimum: 301 [ 0.005122] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.005136] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes, linear) [ 0.009959] rcu: Hierarchical SRCU implementation. [ 0.009967] rcu: Max phase no-delay instances is 1000. [ 0.010299] Timer migration: 1 hierarchy levels; 8 children per group; 1 crossnode level [ 0.010704] smp: Bringing up secondary CPUs ... [ 0.011369] Detected VIPT I-cache on CPU1 [ 0.011480] CPU1: Booted secondary processor 0x0000000001 [0x410fd034] [ 0.012235] Detected VIPT I-cache on CPU2 [ 0.012310] CPU2: Booted secondary processor 0x0000000002 [0x410fd034] [ 0.013076] Detected VIPT I-cache on CPU3 [ 0.013147] CPU3: Booted secondary processor 0x0000000003 [0x410fd034] [ 0.013227] smp: Brought up 1 node, 4 CPUs [ 0.013236] SMP: Total of 4 processors activated. [ 0.013240] CPU: All CPU(s) started at EL1 [ 0.013244] CPU features: detected: 32-bit EL0 Support [ 0.013248] CPU features: detected: CRC32 instructions [ 0.013288] alternatives: applying system-wide alternatives [ 0.013481] CPU features: emulated: Privileged Access Never (PAN) using TTBR0_EL1 switching [ 0.013747] Memory: 409704K/524288K available (8832K kernel code, 900K rwdata, 2884K rodata, 960K init, 289K bss, 111620K reserved, 0K cma-reserved) [ 0.022553] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.022579] futex hash table entries: 1024 (order: 4, 65536 bytes, linear) [ 0.022699] 29248 pages in range for non-PLT usage [ 0.022704] 520768 pages in range for PLT usage [ 0.024829] pinctrl core: initialized pinctrl subsystem [ 0.026948] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.027768] DMA: preallocated 2048 KiB GFP_KERNEL pool for atomic allocations [ 0.028069] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations [ 0.028371] DMA: preallocated 2048 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations [ 0.028792] thermal_sys: Registered thermal governor 'step_wise' [ 0.028852] cpuidle: using governor menu [ 0.029068] ASID allocator initialised with 65536 entries [ 0.060684] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 0.083155] SCSI subsystem initialized [ 0.083377] usbcore: registered new interface driver usbfs [ 0.083418] usbcore: registered new interface driver hub [ 0.083451] usbcore: registered new device driver usb [ 0.083761] qcom_scm: convention: smc arm 64 [ 0.085515] clocksource: Switched to clocksource arch_sys_counter [ 0.089190] NET: Registered PF_INET protocol family [ 0.089332] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.091314] tcp_listen_portaddr_hash hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.091334] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.091349] TCP established hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.091398] TCP bind hash table entries: 4096 (order: 5, 131072 bytes, linear) [ 0.091547] TCP: Hash tables configured (established 4096 bind 4096) [ 0.091885] MPTCP token hash table entries: 512 (order: 2, 12288 bytes, linear) [ 0.092048] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.092074] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.092514] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.092554] PCI: CLS 0 bytes, default 64 [ 0.094393] workingset: timestamp_bits=46 max_order=17 bucket_order=0 [ 0.094969] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.094976] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.100280] qcom-qmp-usb-phy 78000.phy: supply vdda-phy not found, using dummy regulator [ 0.100428] qcom-qmp-usb-phy 78000.phy: supply vdda-pll not found, using dummy regulator [ 0.101511] qcom-qusb2-phy 79000.phy: supply vdd not found, using dummy regulator [ 0.101668] qcom-qusb2-phy 79000.phy: supply vdda-pll not found, using dummy regulator [ 0.101742] qcom-qusb2-phy 79000.phy: supply vdda-phy-dpdm not found, using dummy regulator [ 0.110033] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.110998] msm_serial 78b3000.serial: msm_serial: detected port #0 [ 0.111101] msm_serial 78b3000.serial: uartclk = 3686400 [ 0.111460] 78b3000.serial: ttyMSM0 at MMIO 0x78b3000 (irq = 20, base_baud = 230400) is a MSM [ 0.111506] msm_serial: console setup on port #0 [ 0.111542] printk: legacy console [ttyMSM0] enabled [ 0.907309] msm_serial: driver initialized [ 0.917132] loop: module loaded [ 0.918534] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xa1 [ 0.919098] nand: Winbond W29N01HZ [ 0.925705] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 0.930851] spmi_pmic_arb 200f000.spmi: PMIC arbiter version v2 (0x20010000) [ 0.954138] i2c_dev: i2c /dev entries driver [ 0.961534] sdhci: Secure Digital Host Controller Interface driver [ 0.961582] sdhci: Copyright(c) Pierre Ossman [ 0.966657] sdhci-pltfm: SDHCI platform and OF driver helper [ 0.972874] remoteproc remoteproc0: releasing cd00000.q6v5_wcss [ 0.980439] NET: Registered PF_INET6 protocol family [ 0.983894] Segment Routing with IPv6 [ 0.987743] In-situ OAM (IOAM) with IPv6 [ 0.991254] NET: Registered PF_PACKET protocol family [ 0.995331] 8021q: 802.1Q VLAN Support v1.8 [ 1.032560] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 [ 1.032965] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0 [ 1.038717] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 1 [ 1.045290] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0 [ 1.052960] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable [ 1.060478] cpr3_mem_acc_init: apc: not using memory accelerator regulator [ 1.069603] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused SVS: open-loop= 704000 uV [ 1.076550] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused NOM: open-loop= 816000 uV [ 1.086534] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused TURBO: open-loop= 880000 uV [ 1.096347] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused STURBO: open-loop= 960000 uV [ 1.106201] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused SVS: quot[ 7]= 716, quot_offset[ 7]= 0 [ 1.115962] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused NOM: quot[ 7]= 935, quot_offset[ 7]= 215 [ 1.126812] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused TURBO: quot[ 7]=1047, quot_offset[ 7]= 110 [ 1.137751] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused STURBO: quot[ 7]=1198, quot_offset[ 7]= 150 [ 1.148933] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop [ 1.152635] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xa1 [ 1.166417] nand: Winbond W29N01HZ [ 1.172796] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.176367] 17 qcomsmem partitions found on MTD device qcom_nand.0 [ 1.183569] Creating 17 MTD partitions on "qcom_nand.0": [ 1.189754] 0x000000000000-0x000000100000 : "0:sbl1" [ 1.196658] 0x000000100000-0x000000200000 : "0:mibib" [ 1.201522] 0x000000200000-0x000000280000 : "0:bootconfig" [ 1.205937] 0x000000280000-0x000000300000 : "0:bootconfig1" [ 1.211291] 0x000000300000-0x000000600000 : "0:qsee" [ 1.218979] 0x000000600000-0x000000680000 : "0:devcfg" [ 1.222001] 0x000000680000-0x000000700000 : "0:apdp" [ 1.227003] 0x000000700000-0x000000780000 : "0:rpm" [ 1.232046] 0x000000780000-0x000000800000 : "0:cdt" [ 1.236702] 0x000000800000-0x000000980000 : "0:appsblenv" [ 1.242389] 0x000000980000-0x000000b80000 : "0:appsbl" [ 1.248367] 0x000000b80000-0x000000c00000 : "0:art" [ 1.252127] 0x000000c00000-0x000003600000 : "rootfs" [ 1.291785] mtd: setting mtd12 (rootfs) as root device [ 1.292116] mtdsplit: no squashfs found in "rootfs" [ 1.295870] 0x000003600000-0x000006000000 : "rootfs_1" [ 1.336222] 0x000006000000-0x000006080000 : "0:ethphyfw" [ 1.337115] 0x000006080000-0x000006980000 : "factory_data" [ 1.348584] 0x000006980000-0x000007a80000 : "runtime_data" [ 1.370676] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 800000 KHz, changing to: 1017600 KHz [ 1.373230] remoteproc remoteproc0: cd00000.q6v5_wcss is available [ 1.381025] ubi0: attaching mtd12 [ 1.602357] ubi0: scanning is finished [ 1.656081] ubi0: attached mtd12 (name "rootfs", size 42 MiB) [ 1.656124] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 1.660818] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 1.667610] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 1.674446] ubi0: good PEBs: 336, bad PEBs: 0, corrupted PEBs: 0 [ 1.681226] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 [ 1.687476] ubi0: max/mean erase counter: 12/9, WL threshold: 4096, image sequence number: 898308538 [ 1.694504] ubi0: available PEBs: 0, total reserved PEBs: 336, PEBs reserved for bad PEB handling: 20 [ 1.703814] ubi0: background thread "ubi_bgt0d" started, PID 613 [ 1.704689] block ubiblock0_1: created from ubi0:1(rootfs) [ 1.719121] clk: Disabling unused�[ 1.732271] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 1.732756] Freeing unused kernel memory: 960K [ 1.738553] Run /sbin/init as init process [ 2.004349] init: Console is alive [ 2.004487] init: - watchdog - [ 2.552112] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.624437] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 2.713551] ssdk_dt_parse_interrupt[942]:INFO:intr-gpio does not exist [ 3.091622] regi_init[2525]:INFO:Initializing HPPE Done!! [ 3.091735] regi_init[2574]:INFO:qca-ssdk module init succeeded! [ 3.098613] EDMA ver 1 hw init [ 3.102308] EDMA HW Reset completed succesfully [ 3.104983] Num rings - TxDesc:1 (23-23) TxCmpl:1 (7-7) [ 3.109400] RxDesc:1 (15-15) RxFill:1 (7-7) [ 3.115014] GMAC4(ffffff8002383940) Invalid MAC@ - using ca:a7:d9:0b:88:8c [ 3.296237] Qualcomm QCA8072 90000.mdio-1:03: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:03, irq=POLL) [ 3.297326] GMAC5(ffffff8002380940) Invalid MAC@ - using b6:af:4b:11:a1:47 [ 3.365845] Qualcomm QCA8072 90000.mdio-1:04: attached PHY driver (mii_bus:phy_addr=90000.mdio-1:04, irq=POLL) [ 3.366801] ********************************************************** [ 3.374744] * NSS Data Plane driver [ 3.381275] ********************************************************** [ 3.399458] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.399516] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 1 [ 3.403991] xhci-hcd xhci-hcd.1.auto: hcc params 0x0220fe65 hci version 0x110 quirks 0x0000808002000010 [ 3.411480] xhci-hcd xhci-hcd.1.auto: irq 39, io mem 0x08a00000 [ 3.420926] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 3.426695] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 2 [ 3.432243] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 3.440279] hub 1-0:1.0: USB hub found [ 3.446412] hub 1-0:1.0: 1 port detected [ 3.450412] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 3.454523] hub 2-0:1.0: USB hub found [ 3.462312] hub 2-0:1.0: 1 port detected [ 3.469530] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 3.477920] init: - preinit - [ 3.859838] ubi15: attaching mtd15 [ 3.907393] ubi15: scanning is finished [ 3.975937] ubi15: attached mtd15 (name "factory_data", size 9 MiB) [ 3.975981] ubi15: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.981021] ubi15: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.987985] ubi15: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.994910] ubi15: good PEBs: 72, bad PEBs: 0, corrupted PEBs: 0 [ 4.002121] ubi15: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 4.008113] ubi15: max/mean erase counter: 11/6, WL threshold: 4096, image sequence number: 1864824124 [ 4.015140] ubi15: available PEBs: 0, total reserved PEBs: 72, PEBs reserved for bad PEB handling: 20 [ 4.024535] ubi15: background thread "ubi_bgt15d" started, PID 788 UBI device number 15, total 72 LEBs (9142272 bytes, 8.7 MiB), av[ 4.041657] UBIFS (ubi15:0): Mounting in unauthenticated mode ailable 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) [ 4.083188] UBIFS (ubi15:0): recovery needed [ 4.127677] UBIFS (ubi15:0): recovery deferred [ 4.127747] UBIFS (ubi15:0): UBIFS: mounted UBI device 15, volume 0, name "ubi_factory_data", R/O mode [ 4.131012] UBIFS (ubi15:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 4.140315] UBIFS (ubi15:0): FS size: 4825088 bytes (4 MiB, 38 LEBs), max 48 LEBs, journal size 1142785 bytes (1 MiB, 9 LEBs) [ 4.150295] UBIFS (ubi15:0): reserved for root: 0 bytes (0 KiB) [ 4.161654] UBIFS (ubi15:0): media format: w4/r0 (latest is w5/r0), UUID D7447E3F-6F68-4E39-B5DF-9EE92604DC7F, small LPT model [ 4.176903] ubi16: attaching mtd16 [ 4.205527] random: crng init done [ 4.266023] ubi16: scanning is finished [ 4.315933] ubi16: attached mtd16 (name "runtime_data", size 17 MiB) [ 4.315975] ubi16: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.321363] ubi16: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.328069] ubi16: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.334991] ubi16: good PEBs: 136, bad PEBs: 0, corrupted PEBs: 0 [ 4.342204] ubi16: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 4.348194] ubi16: max/mean erase counter: 17/11, WL threshold: 4096, image sequence number: 1626932842 [ 4.355309] ubi16: available PEBs: 0, total reserved PEBs: 136, PEBs reserved for bad PEB handling: 20 [ 4.364707] ubi16: background thread "ubi_bgt16d" started, PID 804 UBI device number 16, total 136 LEBs (17268736 bytes, 16.4 MiB),[ 4.381656] UBIFS (ubi16:0): Mounting in unauthenticated mode available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) [ 4.424551] UBIFS (ubi16:0): recovery needed [ 4.451769] UBIFS (ubi16:0): recovery deferred [ 4.451850] UBIFS (ubi16:0): UBIFS: mounted UBI device 16, volume 0, name "ubi_runtime_data", R/O mode [ 4.455108] UBIFS (ubi16:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 4.464417] UBIFS (ubi16:0): FS size: 9904128 bytes (9 MiB, 78 LEBs), max 88 LEBs, journal size 1777664 bytes (1 MiB, 14 LEBs) [ 4.474395] UBIFS (ubi16:0): reserved for root: 0 bytes (0 KiB) [ 4.485752] UBIFS (ubi16:0): media format: w4/r0 (latest is w5/r0), UUID 9796B8EA-F494-4085-9A40-ECE182394428, small LPT model Cannot parse config file '/etc/fw_env.config': No such file or directory Failed to find NVMEM device Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.085837] nss-dp 3a001600.dp4 lan: PHY Link up speed: 1000 [ 9.238149] UBIFS (ubi0:2): Mounting in unauthenticated mode [ 9.238286] UBIFS (ubi0:2): background thread "ubifs_bgt0_2" started, PID 889 [ 9.332230] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name "rootfs_data" [ 9.332272] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 9.339070] UBIFS (ubi0:2): FS size: 23744512 bytes (22 MiB, 187 LEBs), max 197 LEBs, journal size 1142784 bytes (1 MiB, 9 LEBs) [ 9.348960] UBIFS (ubi0:2): reserved for root: 1121511 bytes (1095 KiB) [ 9.360580] UBIFS (ubi0:2): media format: w5/r0 (latest is w5/r0), UUID 2CD0DC49-9171-4058-BB40-2DC3850491C6, small LPT model [ 9.368007] mount_root: overlay filesystem has not been fully initialized yet [ 9.378687] mount_root: switching to ubifs overlay [ 9.389669] overlayfs: null uuid detected in lower fs '/', falling back to xino=off,index=off,nfs_export=off. - config restore - [ 9.527275] urandom-seed: Seed file not found (/etc/urandom.seed) - generating board file - [ 9.714231] nss-dp 3a001600.dp4 lan: PHY Link is down [ 9.718712] procd: - early - [ 9.718824] procd: - watchdog - [ 10.283171] procd: - watchdog - [ 10.283407] procd: - ubus - [ 10.439962] procd: - init - Please press Enter to activate this console. [ 10.889719] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.979722] urngd: v1.0.2 started. [ 11.044342] Loading modules backported from Linux version v6.18.26-0-g1fe060681 [ 11.044390] Backport generated by backports.git 6ecbb44 [ 11.062365] NET: Registered PF_QIPCRTR protocol family [ 11.195841] PPP generic driver version 2.4.2 [ 11.196897] NET: Registered PF_PPPOX protocol family [ 11.238444] ath11k c000000.wifi: ipq8074 hw2.0 [ 11.238484] ath11k c000000.wifi: FW memory mode: 1 [ 11.281552] remoteproc remoteproc0: powering up cd00000.q6v5_wcss [ 11.281972] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668 [ 12.512964] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up [ 12.564684] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0xff soc_id 0xffffffff [ 12.564739] ath11k c000000.wifi: fw_version 0x290b84a5 fw_build_timestamp 2024-09-23 11:32 fw_build_id WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1 [ 17.797525] remoteproc remoteproc0: stopped remote processor cd00000.q6v5_wcss [ 17.797579] remoteproc remoteproc0: powering up cd00000.q6v5_wcss [ 17.803827] remoteproc remoteproc0: Booting fw image IPQ8074/q6_fw.mdt, size 668 [ 18.157292] remoteproc remoteproc0: remote processor cd00000.q6v5_wcss is now up [ 18.164825] batman_adv: B.A.T.M.A.N. advanced 6.12.93 (compatibility version 15) loaded [ 18.168457] kmodloader: done loading kernel modules from /etc/modules.d/* [ 18.208521] ath11k c000000.wifi: chip_id 0x0 chip_family 0x0 board_id 0xff soc_id 0xffffffff [ 18.208580] ath11k c000000.wifi: fw_version 0x290b84a5 fw_build_timestamp 2024-09-23 11:32 fw_build_id WLAN.HK.2.9.0.1-02146-QCAHKSWPL_SILICONZ-1 [ 18.382509] ath11k c000000.wifi: htt event 48 not handled [ 21.452194] br-lan: port 1(lan) entered blocking state [ 21.452247] br-lan: port 1(lan) entered disabled state [ 21.456374] nss-dp 3a001600.dp4 lan: entered allmulticast mode [ 21.461700] nss-dp 3a001600.dp4 lan: entered promiscuous mode [ 21.767187] br-lan: port 2(phy0-ap0) entered blocking state [ 21.767239] br-lan: port 2(phy0-ap0) entered disabled state [ 21.771640] ath11k c000000.wifi phy0-ap0: entered allmulticast mode [ 21.777461] ath11k c000000.wifi phy0-ap0: entered promiscuous mode [ 22.261417] br-lan: port 2(phy0-ap0) entered blocking state [ 22.261476] br-lan: port 2(phy0-ap0) entered forwarding state [ 24.565842] nss-dp 3a001600.dp4 lan: PHY Link up speed: 1000 [ 24.565910] br-lan: port 1(lan) entered blocking state [ 24.570588] br-lan: port 1(lan) entered forwarding state [ 24.576139] nss-dp 3a001800.dp5 wan: PHY Link up speed: 1000 [ 31.845571] l11: disabling

WIP Unsupported devices qualcommax ipq807x 128nand 512ram 4core ath11k 2port gigabitethernet qcn5054 qcn5024 wifi6 802.11ax 802.11ac 802.11bgn armv8 internalantenna 1 button 12v powered u-boot

TP-Link Deco X60 2

OpenWrt support

Supporting activities

Hardware highlights

Hardware

Info

Photos

Opening the case

Serial

Bootlogs

OEM bootlog

OpenWrt bootlog

Notes

Tags