Sercomm S3

This is AC2100 dual Band Wireless Router which now supports OpenWrt

Generic Router

Brand Model SoC CPU Ram Flash WLAN Hardware WLAN 2.4 GHz WLAN 5 GHz Gbit ports ZigBee USB Serial
Sercomm S3 MediaTek MT7621AT 880 MHz 256 MiB 128 MiB MediaTek MT7603EN, MediaTek MT7615N b/g/n a/n/ac 5 No 1x 3.0 Yes
Beeline Smart Box TURBO MediaTek MT7621AT 880 MHz 256 MiB 256 MiB MediaTek MT7603EN, MediaTek MT7615N b/g/n a/n/ac 5 No 1x 3.0 Yes
Beeline Smart Box TURBO+ MediaTek MT7621AT 880 MHz 128 MiB 128 MiB MediaTek MT7603EN, MediaTek MT7615N b/g/n a/n/ac 5 Yes 1x 3.0 Yes

1. Login to the router web interface under admin account

2. Navigate to Settings → Configuration

3. Upload this modified config file (config file password is E1234) . https://github.com/Shahid247/sercomm_s3_change_bootflag/blob/main/Sercomm_s3_config.cfg

4. Login via Putty SSH 192.168.1.1 under user=SuperUser password=E12345678

5. Once logged in type

sh

6. Change bootflag to Sercomm1 and reboot:

printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot

7. After restart login to web interface with user=admin password=E12345678 & upload etisalat_s3-squashfs-factory.img

8. Now openwrt boots & boot flag will automatically changes to “Boot Flag : Sercomm0”

9. Now we have Successfully installed Openwrt in slot 0, while we still have OEM Firmware stored in slot 1. If you want to revert back to oem follow the section.

1. Change the bootflag to Sercomm1 in OpenWrt CLI and then reboot:

printf 1 | dd bs=1 seek=7 count=1 of=/dev/mtdblock3
reboot

2. Stock firmware will boot from slot 1 & automatically replaces OpenWrt in slot 0 with OEM Firmware.

It's recommended to make a mtd backup before you start:

1. Set up a tftp server (e.g. tftpd64 for windows)

2. Set your pc ip address 192.168.1.2

3. Connect to a router using SSH shell with SuperUser and run the following commands:

sh
cd /tmp
for i in 0 1 2 3 4 5 6 7 8 9 10; do nanddump -f mtd$i /dev/mtd$i; \
tftp -l mtd$i -p 192.168.1.2; md5sum mtd$i >> mtd.md5; rm mtd$i; done
tftp -l mtd.md5 -p 192.168.1.2
Architecture mipsel_24kc
Vendor Sercomm
Bootloader U-Boot 1.1.3
System-On-Chip MediaTek MT7621AT
CPU/Speed 880 Mhz 2 cores
Flash-Chip MXIC MX30LF1G18AC
Flash size 128 MiB Nand
RAM 256 MiB
Wireless MT7603E MT7615E
Ethernet MT7621AT
Switch MT7621AT
USB 1x 3.0
Serial Yes 57600 8N1
JTAG Not populated
dev:    size   erasesize  name
mtd0: 00100000 00020000 "u-boot"
mtd1: 00100000 00020000 "dynamic partition map"
mtd2: 00100000 00020000 "Factory"
mtd3: 00100000 00020000 "Boot Flag"
mtd4: 00600000 00020000 "kernel"
mtd5: 00600000 00020000 "Kernel 2"
mtd6: 02000000 00020000 "File System 1"
mtd7: 02000000 00020000 "File System 2"
mtd8: 01400000 00020000 "Configuration/log"
mtd9: 01b80000 00020000 "application tmp buffer (Ftool)"
mtd10: 04f80000 00020000 "ubi"

mtd2 contains following information

Info Offset
Macaddr 21000
Serial Number / SuperUser password 21010
WPS PIN 21070
admin password 210E0

 mtd2-HXD Output

sercomm_s3_pcb_front

sercomm_s3_pcb_front

sercomm_s3_pcb_back

sercomm_s3_label

Under large rubber pads there are two screws, Unscrew & open locks gently with plastic tool.

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Sercomm Model S3 Serial

Serial connection parameters for Sercomm S3 56700, 8N1

Built in shell access

User: SuperUser

Password: SN (Printed on the back of your router) & can also be found in oem bootlog

once logged in type sh press enter for shell access.

port.jtag general information about the JTAG port, JTAG cable, etc.

There is no Jtag on this board

=================================================================== MT7621 stage1 code 10:33:11 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0xb, 1/0 = 551/473 2D000000 PLL2 FB_DL: 0x13, 1/0 = 513/511 4D000000 PLL4 FB_DL: 0x13, 1/0 = 515/509 4D000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 000F:| 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0010:| 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0011:| 1 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 16 rank 0 fine = 40 B:| 0 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 opt_dle value:9 DRAMC_R0DELDLY[018]=00001E1E ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 13 7 13 10 12 7 11 5 3 9 10 | 6 12 7 9 3 10 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =30 DQS1 = 30 ================================================================== bit DQS0 bit DQS1 0 (1~60)30 8 (1~57)29 1 (1~56)28 9 (1~58)29 2 (1~59)30 10 (1~60)30 3 (1~57)29 11 (1~57)29 4 (1~58)29 12 (1~59)30 5 (1~59)30 13 (1~58)29 6 (1~58)29 14 (1~60)30 7 (0~58)29 15 (1~58)29 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 13 9 13 11 13 7 12 6 4 10 10 | 6 13 7 10 3 11 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffffba00 dqs_perbyte_dly.last_dqsdly_pass[0]=15, finish count=1 DQS loop = 14, cmp_err_1 = ffff2a00 DQS loop = 13, cmp_err_1 = ffff2800 DQS loop = 12, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[1]=12, finish count=2 DQ loop=15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,9) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Mar 4 2020 - 17:12:16) Board: Ralink APSoC DRAM: 256 MB rt2880 uboot v0.00e04 05/25/2006 SERIAL_CLOCK_DIVISOR =16 kaiker,,CONFIG_BAUDRATE =57600 SDRAM SIZE:10000000 Top of RAM usable for U-Boot at: 90000000 Reserving 425k for U-Boot at: 8ff94000 Reserving 1028k for malloc() at: 8fe93000 Reserving 44 Bytes for Board Info at: 8fe92fd4 Reserving 36 Bytes for Global Data at: 8fe92fb0 Reserving 128k for boot params() at: 8fe72fb0 Stack Pointer at: 8fe72f98 relocate_code Pointer at: 8ff94000 Config XHCI 40M PLL Now running in RAM - U-Boot at: 8ff94000 monitor_flash_len =116812 Command "mdio": 0xa0206984 => 0x8ff9a984 Command "nand": 0xa020c2bc => 0x8ffa02bc Command "reset": 0xa0215cec => 0x8ffa9cec Command "go": 0xa020dc68 => 0x8ffa1c68 Command "bootm": 0xa020e4c4 => 0x8ffa24c4 Command "loadb": 0xa020f184 => 0x8ffa3184 Command "tftpboot": 0xa020f7b4 => 0x8ffa37b4 Command "nm": 0xa020fe40 => 0x8ffa3e40 Command "mm": 0xa020fea4 => 0x8ffa3ea4 Command "md": 0xa020ff08 => 0x8ffa3f08 Command "saveenv": 0xa0210480 => 0x8ffa4480 Command "setenv": 0xa0210df0 => 0x8ffa4df0 Command "printenv": 0xa02104d0 => 0x8ffa44d0 Command "?": 0xa02110c4 => 0x8ffa50c4 Command "help": 0xa02110c4 => 0x8ffa50c4 Command "version": 0xa0210f84 => 0x8ffa4f84 Command "sc_boot": 0xa0213d30 => 0x8ffa7d30 Command "sc_nand": 0xa0213d68 => 0x8ffa7d68 Command "sc_eth_test": 0xa0213da4 => 0x8ffa7da4 Command "sc_phy": 0xa0213de0 => 0x8ffa7de0 Command "sc_time": 0xa0213e1c => 0x8ffa7e1c Command "sc_btver": 0xa0213e54 => 0x8ffa7e54 Command "sc_fl_map": 0xa0213e90 => 0x8ffa7e90 Command "sc_endian": 0xa0213ecc => 0x8ffa7ecc Command "sc_gpio": 0xa0213f08 => 0x8ffa7f08 Command "sc_led": 0xa0213f44 => 0x8ffa7f44 Command "sc_dl": 0xa0213f80 => 0x8ffa7f80 Allocate 16 byte aligned buffer: 8ffca410 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02] Device found in MTK table, ID: c2f1, EXT_ID: 809502 Support this Device in MTK table! c2f1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 *** Warning - bad CRC, using default environment icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes #Reset_MT7530 set LAN/WAN WLLLL Load Standalone from 40000 SC_DEBUG: Nand Partition Table Magic Found at 100000. ****************************************** Uboot StandAlone Entry ****************************************** GPIO init ********************************************************* Press any key to enter Boot Command Interface ********************************************************* 0 SC_DEBUG: Nand Partition Table Magic Found at 100000. ****************************************** Uboot StandAlone Entry ****************************************** *************************************************** Boot Version 0.2.1.0, at Mar 4 2020, 17:12:13 *************************************************** SC_DEBUG: Nand Partition Table Magic Found at 100000. Entering Firmware : Everything is OK. ************************************* Boot Flag : Sercomm1▒ ************************************* Fw header Magic check OK! FW header checksum should: 0x67ed9adf, crc32 result: 0x67ed9adf, Fw header CRC check OK! kernel : real offset: 0x00a00100, data length: 0x003b772b,checksum :0xcd873b74 kernel result: 0xcd873b74, kernel check sum ok! rootfs: real offset: 0x03000000, data length: 0x00ea4000, checksum :0xa0bc104a rootfs result: 0xa0bc104a, rootfs check sum ok! Kernel Addr : 0xbca00100 ## Booting image at bca00100 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 3897067 Bytes = 3.7 MB Load Address: 81001000 Entry Point: 81721b00 Verifying Checksum ... OK Uncompressing Kernel Image ... OK kernel addr :0xBCA00100 No initrd ## Transferring control to Linux (at address 81721b00) ... ## Giving linux memsize in MB, 256 Starting kernel ... LINUX started... THIS IS ASIC SDK 5.0.S.0 Linux version 3.10.14 (scof@ubuntu) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 SMP Sun Sep 27 05:34:50 MSK 2020 The CPU feqenuce set to 880 MHz GCMP present CPU0 revision is: 0001992f (MIPS 1004Kc) Software DMA cache coherency Determined physical RAM map: memory: 0fffc000 @ 00000000 (usable) memory: 00004000 @ 0fffc000 (reserved) Zone ranges: DMA [mem 0x00000000-0x00ffffff] Normal [mem 0x01000000-0x0fffbfff] Movable zone start for each node Early memory node ranges node 0: [mem 0x00000000-0x0fffbfff] Detected 3 available secondary CPU(s) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. PERCPU: Embedded 7 pages/cpu @81d5e000 s6720 r8192 d13760 u32768 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65020 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 rootfstype=squashfs PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Writing ErrCtl register=00053ed8 Readback ErrCtl register=00053ed8 Memory: 248120k/262128k available (7341k kernel code, 14008k reserved, 3137k data, 268k init, 0k highmem) SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 Hierarchical RCU implementation. NR_IRQS:128 console [ttyS1] enabled Calibrating delay loop... 577.53 BogoMIPS (lpj=1155072) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 launch: starting cpu1 launch: cpu1 gone! CPU1 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 1: done. launch: starting cpu2 launch: cpu2 gone! CPU2 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 2: done. launch: starting cpu3 launch: cpu3 gone! CPU3 revision is: 0001992f (MIPS 1004Kc) Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes MIPS secondary cache 256kB, 8-way, linesize 32 bytes. Synchronize counters for CPU 3: done. Brought up 4 CPUs devtmpfs: initialized NET: Registered protocol family 16 release PCIe RST: RALINK_RSTCTRL = 7000000 PCIE PHY initialize ***** Xtal 40MHz ***** start MT7621 PCIe register access RALINK_RSTCTRL = 7000000 RALINK_CLKCFG1 = 77ffeff8 *************** MT7621 PCIe RC mode ************* PCIE2 no card, disable it(RST&CLK) pcie_link status = 0x3 RALINK_RSTCTRL= 3000000 *** Configure Device number setting of Virtual PCI-PCI bridge *** RALINK_PCI_PCICFG_ADDR = 21007f2 -> 21007f2 PCIE0 enabled PCIE1 enabled interrupt enable status: 300000 Port 1 N_FTS = 1b105000 Port 0 N_FTS = 1b105000 config reg done init_rt2880pci done bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb PCI host bridge to bus 0000:00 pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:01.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] pci 0000:00:01.0: BAR 8: assigned [mem 0x60100000-0x601fffff] pci 0000:00:00.0: BAR 1: assigned [mem 0x60200000-0x6020ffff] pci 0000:00:01.0: BAR 1: assigned [mem 0x60210000-0x6021ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] pci 0000:00:00.0: PCI bridge to [bus 01] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] pci 0000:02:00.0: BAR 0: assigned [mem 0x60100000-0x601fffff] pci 0000:00:01.0: PCI bridge to [bus 02] pci 0000:00:01.0: bridge window [mem 0x60100000-0x601fffff] PCI: Enabling device 0000:00:00.0 (0004 -> 0006) PCI: Enabling device 0000:00:01.0 (0004 -> 0006) BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60200000 res[1]->end = 6020ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 BAR0 at slot 1 = 0 bus=0x0, slot = 0x1 res[0]->start = 0 res[0]->end = 0 res[1]->start = 60210000 res[1]->end = 6021ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0, irq=0x4 res[0]->start = 60000000 res[0]->end = 600fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x2, slot = 0x1, irq=0x18 res[0]->start = 60100000 res[0]->end = 601fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource MIPS NET: Registered protocol family 2 TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 4 CPUs re-calibrate udelay(lpj = 1167360) squashfs: version 4.0 (2009/01/31) Phillip Lougher NTFS driver 2.1.30 [Flags: R/W]. fuse init (API version 7.22) msgmni has been set to 484 io scheduler noop registered (default) reg_int_mask=0, INT_MASK= 0 HSDMA_init hsdma_phy_tx_ring0 = 0x00c00000, hsdma_tx_ring0 = 0xa0c00000 hsdma_phy_rx_ring0 = 0x00c04000, hsdma_rx_ring0 = 0xa0c04000 TX_CTX_IDX0 = 0 TX_DTX_IDX0 = 0 RX_CRX_IDX0 = 3ff RX_DRX_IDX0 = 0 set_fe_HSDMA_glo_cfg HSDMA_GLO_CFG = 465 Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x1e000d00 (irq = 27) is a 16550A serial8250: ttyS1 at MMIO 0x1e000c00 (irq = 26) is a 16550A serial8250: ttyS2 at MMIO 0x1e000e00 (irq = 28) is a 16550A brd: module loaded MediaTek Nand driver init, version v2.1 Fix AHB virt2phys error Allocate 16 byte aligned buffer: 81a97e00 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02, 00809502] Device found in MTK table, ID: c2f1, EXT_ID: 809502 alloctare : (mtd->writesize + mtd->oobsize) * page_per_block is 135168 Support this Device in MTK table! c2f1 NAND device: Manufacturer ID: 0xc2, Chip ID: 0xf1 (Macronix NAND 128MiB 3,3V 8-bit), 128MiB, page size: 2048, OOB size: 64 [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Scanning device for bad blocks Bad eraseblock 544 at 0x000004400000 Signature matched and data read! load_fact_bbt success 1023 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 03 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 page: 200 Found dynamic partition map at 100000: page: 201 <0> offset: 00000000, length: 00100000 page: 201 <1> offset: 00100000, length: 00100000 page: 201 <2> offset: 00200000, length: 00100000 page: 201 <3> offset: 00300000, length: 00100000 page: 201 <4> offset: 00400000, length: 00600000 page: 201 <5> offset: 00A00000, length: 00600000 page: 201 <6> offset: 01000000, length: 02000000 page: 201 <7> offset: 03000000, length: 02020000 page: 201 <8> offset: 05020000, length: 01400000 page: 201 <9> offset: 06420000, length: 01B60000 Creating 10 MTD partitions on "MT7621-NAND": 0x000000000000-0x000000100000 : "Boot Loader" 0x000000100000-0x000000200000 : "dynamic partition map" 0x000000200000-0x000000300000 : "Factory" 0x000000300000-0x000000400000 : "Boot Flag" 0x000000400000-0x000000a00000 : "Kernel 1" 0x000000a00000-0x000001000000 : "Kernel 2" 0x000001000000-0x000003000000 : "File System 1" 0x000003000000-0x000005020000 : "File System 2" 0x000005020000-0x000006420000 : "Configuration/log" 0x000006420000-0x000007f80000 : "Debug (Ftool)" [mtk_nand] probe successfully! PPP generic driver version 2.4.2 PPP BSD Compression module registered PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 register mt_drv == pAd = c0181000, size = 5763200, Status=0 == pAd->PciHif.CSRBaseAddress =0xc0080000, csr_addr=0xc0080000! RTMPInitPCIeDevice():device_id=0x7615 mt_pci_chip_cfg(): HWVer=0x8a10, FWVer=0x8a10, pAd->ChipID=0x7615 mt_pci_chip_cfg(): HIF_SYS_REV=0x76150001 AP Driver version-5.0.4.0 RtmpChipOpsHook(223): Not support for HIF_MT yet! MACVersion=0x0 mt7615_init()--> Use 1st iPAiLNA default bin. Use 0st /etc_ro/wlan/MT7615E_EEPROM1.bin default bin. <--mt7615_init() <-- RTMPAllocTxRxRingMemory, Status=0 rdm_major = 253 set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288071 Ralink APSoC Ethernet Driver Initilization. v3.1 4096 rx/tx descriptors allocated, mtu = 1500! set CLK_CFG_0 = 0x40a00020!!!!!!!!!!!!!!!!!!1 GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43288091 <0> !! create link_status PROC !!!!! PROC INIT OK! usbcore: registered new interface driver catc usbcore: registered new interface driver kaweth pegasus: v0.9.3 (2013/04/25), Pegasus/Pegasus II USB Ethernet driver usbcore: registered new interface driver pegasus usbcore: registered new interface driver rtl8150 usbcore: registered new interface driver r8152 usbcore: registered new interface driver asix usbcore: registered new interface driver ax88179_178a usbcore: registered new interface driver cdc_ether usbcore: registered new interface driver cdc_eem usbcore: registered new interface driver dm9601 usbcore: registered new interface driver smsc75xx usbcore: registered new interface driver smsc95xx usbcore: registered new interface driver gl620a usbcore: registered new interface driver net1080 usbcore: registered new interface driver plusb usbcore: registered new interface driver rndis_host usbcore: registered new interface driver cdc_subset usbcore: registered new interface driver zaurus usbcore: registered new interface driver MOSCHIP usb-ethernet driver usbcore: registered new interface driver int51x1 usbcore: registered new interface driver kalmia usbcore: registered new interface driver ipheth usbcore: registered new interface driver sierra_net usbcore: registered new interface driver cx82310_eth usbcore: registered new interface driver cdc_ncm usbcore: registered new interface driver lg-vl600 usbcore: registered new interface driver qmi_wwan usbcore: registered new interface driver cdc_mbim ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver ehci-pci: EHCI PCI platform driver ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver uhci_hcd: USB Universal Host Controller Interface driver usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver usblp usbcore: registered new interface driver cdc_wdm usbcore: registered new interface driver usb-storage Ralink APSoC Hardware Watchdog Timer Init Ingress Classify module ... GACT probability on Mirror/redirect action on Failed to load ipt action u32 classifier Performance counters on Actions configured Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (3876 buckets, 15504 max) ctnetlink v0.93: registering with nfnetlink. NF_TPROXY: Transparent proxy support initialized, version 4.1.0 NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. gre: GRE over IPv4 demultiplexor driver ip_tables: (C) 2000-2006 Netfilter Core Team Type=Linux arp_tables: (C) 2002 David S. Miller TCP: cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team NET: Registered protocol family 17 l2tp_core: L2TP core driver, V2.0 l2tp_ppp: PPPoL2TP kernel driver, V2.0 8021q: 802.1Q VLAN Support v1.8 Sercomm dual images: bootflag=Sercomm1, choose /dev/mtdblock7 as rootfs VFS: Mounted root (squashfs filesystem) readonly on device 31:7. devtmpfs: mounted Freeing unused kernel memory: 268K (81a3d000 - 81a80000) init started: BusyBox v1.15.3 () starting pid 52, tty '': '/etc/rcS' mount: mounting usbfs on /proc/bus/usb failed: No such file or directory register rlt_drv === pAd = c0e01000, size = 2224152 === <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc0d00000, csr_addr=0xc0d00000! device_id =0x7603 RtmpChipOpsHook(474): Not support for HIF_MT yet! mt7603_init()--> mt_bcn_buf_init(224): Not support for HIF_MT yet! <--mt7603_init() load_dev_l1profile()--> match_index_by_chipname() MT7603 found as INDEX0 l1set_profile_path() profile remain /etc/Wireless/RT2860/RT2860.dat l1set_eeprom_offset() eeprom offset remain 0x0 l1set_eeprom_size() eeprom size remain 0x200 l1set_ifname() ifname rename from ra0 to ra l1set_ifname() ifname remain ra l1set_ifname() ifname remain ra l1set_ifname() ifname remain apcli hal_wd: module license 'sercomm' taints kernel. Disabling lock debugging due to kernel taint Init system monitor... Sercomm HWIO Driver: loaded successfully nnat46: module (version Sep 27 2020 06:28:44) loaded. UBI: attaching mtd8 to ubi8 UBI: scanning is finished UBI: attached mtd8 (name "Configuration/log", size 20 MiB) to ubi8 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 160, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 192/128, WL threshold: 4096, image sequence number: 583894523 UBI: available PEBs: 0, total reserved PEBs: 160, PEBs reserved for bad PEB handling: 20 UBI: background thread "ubi_bgt8d" started, PID 100 UBI device number 8, total 160 LEBs (20316160 bytes, 19.4 MiB), UBIFS: background thread "ubifs_bgt8_0" started, PID 102 available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 8, volume 0, name "0" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 15872000 bytes (15 MiB, 125 LEBs), journal size 9023488 bytes (8 MiB, 72 LEBs) UBIFS: reserved for root: 0 bytes (0 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID D24B7CE9-C688-4B5E-8DC8-7EEC373BEB60, small LPT model net/nat/hw_nat/get_mem.c InitMod:40: Ralink HW NAT allocate DMA memory area net/nat/hw_nat/get_mem.c InitMod:46: The DMA memory area has been allocated a0e00000 00e00000 Started WatchDog Timer. get boot version from flash 0210 Bootloader has already been recovered switch register base addr to 0xb0100a00 write offset 0x80, value 0x5d805d80 write offset 0x84, value 0x1d801d80 SERIAL NUMBER: ET2FF5FF15246 FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF:FFFFFFFF Raeth v3.1 (Tasklet) phy_free_head is 0xc92000!!! phy_free_tail_phy is 0xc93ff0!!! txd_pool=a0c98000 phy_txd_pool=00C98000 ei_local->skb_free start address is 0x8ede26cc. free_txd: 00c98010, ei_local->cpu_ptr: 00C98000 POOL HEAD_PTR | DMA_PTR | CPU_PTR ----------------+---------+-------- 0xa0c98000 0x00C98000 0x00C98000 phy_qrx_ring = 0x00c94000, qrx_ring = 0xa0c94000 phy_rx_ring0 = 0x00ca0000, rx_ring[0] = 0xa0ca0000 MT7530 Reset Completed!! change HW-TRAP to 0x117c8f set LAN/WAN WLLLL GMAC1_MAC_ADRH -- : 0x00001050 GMAC1_MAC_ADRL -- : 0x7260325c GDMA2_MAC_ADRH -- : 0x0000000c GDMA2_MAC_ADRL -- : 0x43288014 eth3: ===> VirtualIF_open MT7621 GE2 link rate to 1G CDMA_CSG_CFG = 81000000 GDMA1_FWD_CFG = 20710000 GDMA2_FWD_CFG = 20710000 sc_lan_vlan_id = 1 sc_wan_vlan_id = 2 sc_special_vlan_id = 3 sc_host_queue = 3 rc_cmd=/usr/sbin/rc syslogd start mirror_interface = wizard_active = 1 Turn off bs due to wizard flag rc_cmd=rc lan_isolation start rc_cmd=/usr/sbin/rc prpl_hl start rc_cmd=/usr/sbin/rc wan_switch start rc_cmd=/usr/sbin/rc lan_switch start rc_cmd=/usr/sbin/rc dnrd start rc_cmd=/usr/sbin/rc wlan start prpl_hl: wait connection to UBUSD server... Interface doesn't accept private ioctl... set (8BE2): Invalid argument Interface doesn't accept private ioctl... set (8BE2): Invalid argument Interface doesn't accept private ioctl... set (8BE2): Invalid argument ============guest<2> is disabled============ ============guest<3> is disabled============ ============guest<4> is disabled============ ============guest<6> is disabled============ ============guest<7> is disabled============ ============guest<8> is disabled============ rc_cmd=/usr/sbin/rc lanip start init rc_cmd=/usr/sbin/rc firewall start ScDrvDev_ioctl: CMD: (23) is not supported Jan/01/1970 00:00:38: dhcp6_ctl_authinit: failed to open /tmp/dhcp6sctlkey: No such file or directory iptables: Bad rule (does a matching rule exist in that chain?). rc_cmd=rc lan_isolation start rc_cmd=rc lan_isolation start [Jan 01 00:00:40] radvd: no linklocal address configured for br0 [Jan 01 00:00:40] radvd: can't join ipv6-allrouters on br0 rc_cmd=/usr/sbin/rc networkmap start init modprobe: module networkmap not found in modules.dep rc_cmd=/usr/sbin/rc qos start rc_cmd=/usr/sbin/rc cpm start init Sun Sep 27 06:31:51 UTC 2020 rc_cmd=/usr/sbin/rc httpd start rc: invalid command /usr/sbin/rc coredump start Usage: rc <app> <start|stop|restart|create> [COMMON OPTIONS] e.g.: rc firewall start dmz bind: Address already in use bind: Address already in use rc_cmd=/usr/sbin/rc ieee_802_1x start rc_cmd=/usr/sbin/rc srt restart rc_cmd=/usr/sbin/rc rp start rc_cmd=/usr/sbin/rc udpecho start rc_cmd=/usr/sbin/rc ingress_qos start Sep/27/2020 06:31:51: server6_send: transmit advertise to fe80::c07e:2db1:d2f3:c1ff failed rc_cmd=/usr/sbin/rc ingress_classify start rc_cmd=/usr/sbin/rc qos_remark start rc_cmd=/usr/sbin/rc ipv6wd start rc_cmd=/usr/sbin/rc pppoe_relay start rc_cmd=/usr/sbin/rc telnetd start rc_cmd=/usr/sbin/rc igd_upnp start rc_cmd=/usr/sbin/rc dnsr start rc_cmd=/usr/sbin/rc cron start Sep/27/2020 06:31:52: server6_send: transmit advertise to fe80::c07e:2db1:d2f3:c1ff failed rc_cmd=/usr/sbin/rc prpl_timers start rc_cmd=/usr/sbin/rc cups start rc_cmd=/usr/sbin/rc umtsd start [umtsd] Init daemon [umtsd] Setup signal handlers [umtsd] Start daemon loop, initial state = DISCONNECTED rc_cmd=/usr/sbin/rc cwmp_stun start rc_cmd=/usr/sbin/rc mesh start rc_cmd=/usr/sbin/rc sshd start rc_cmd=rc igd_upnp restart Erasing 128 Kibyte @ 20000 -- 100 % complete rc_cmd=rc event_m start starting pid 907, tty '': '/sbiCould not load host key: /etc/ssh/ssh_host_ed25519_key Etisalat-S3 login: crc = 0xcd873b74 crc = 0xa0bc104a DualImage Sync: images are the same, skip sync crc = 0xcd873b74 crc = 0xa0bc104a crc = 0xcd873b74 crc = 0xa0bc104a crc = 0xd1416571


=================================================================== MT7621 stage1 code 10:33:11 (ASIC) CPU=50000000 HZ BUS=16666666 HZ ================================================================== Change MPLL source from XTAL to CR... do MEMPLL setting.. MEMPLL Config : 0x11100000 3PLL mode + External loopback === XTAL-40Mhz === DDR-1200Mhz === PLL3 FB_DL: 0xb, 1/0 = 565/459 2D000000 PLL4 FB_DL: 0x13, 1/0 = 547/477 4D000000 PLL2 FB_DL: 0x14, 1/0 = 740/284 51000000 do DDR setting..[00320381] Apply DDR3 Setting...(use customer AC) 0 8 16 24 32 40 48 56 64 72 80 88 96 104 112 120 -------------------------------------------------------------------------------- 0000:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0001:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0002:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0003:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0004:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0005:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0006:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0007:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0008:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0009:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 000E:| 0 0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 000F:| 0 0 0 0 0 1 1 1 1 1 1 1 1 1 1 0 0010:| 1 1 1 1 1 1 1 1 1 1 0 0 0 0 0 0 0011:| 1 1 1 1 0 0 0 0 0 0 0 0 0 0 0 0 0012:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0013:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0014:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0015:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0016:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0017:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0018:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0019:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001A:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001B:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001C:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001D:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001E:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 001F:| 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 rank 0 coarse = 16 rank 0 fine = 40 B:| 0 0 0 0 0 0 0 1 1 1 0 0 0 0 0 0 opt_dle value:8 DRAMC_R0DELDLY[018]=00001E1F ================================================================== RX DQS perbit delay software calibration ================================================================== 1.0-15 bit dq delay value ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 13 7 13 10 12 7 11 6 3 9 10 | 6 12 7 8 3 10 -------------------------------------- ================================================================== 2.dqs window x=pass dqs delay value (min~max)center y=0-7bit DQ of every group input delay:DQS0 =31 DQS1 = 30 ================================================================== bit DQS0 bit DQS1 0 (1~60)30 8 (1~57)29 1 (1~56)28 9 (1~60)30 2 (1~60)30 10 (1~60)30 3 (1~57)29 11 (1~56)28 4 (1~58)29 12 (1~60)30 5 (1~59)30 13 (0~58)29 6 (1~59)30 14 (1~60)30 7 (2~60)31 15 (1~59)30 ================================================================== 3.dq delay value last ================================================================== bit| 0 1 2 3 4 5 6 7 8 9 -------------------------------------- 0 | 14 10 14 12 14 8 12 6 4 9 10 | 6 14 7 9 3 10 ================================================================== ================================================================== TX perbyte calibration ================================================================== DQS loop = 15, cmp_err_1 = ffff3b04 DQS loop = 14, cmp_err_1 = ffff2a00 dqs_perbyte_dly.last_dqsdly_pass[0]=14, finish count=1 DQS loop = 13, cmp_err_1 = ffff2200 DQS loop = 12, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqsdly_pass[1]=12, finish count=2 DQ loop=15, cmp_err_1 = ffff0000 dqs_perbyte_dly.last_dqdly_pass[0]=15, finish count=1 dqs_perbyte_dly.last_dqdly_pass[1]=15, finish count=2 byte:0, (DQS,DQ)=(8,8) byte:1, (DQS,DQ)=(8,9) 20,data:88 [EMI] DRAMC calibration passed =================================================================== MT7621 stage1 code done CPU=50000000 HZ BUS=16666666 HZ =================================================================== U-Boot 1.1.3 (Mar 4 2020 - 17:12:16) Board: Ralink APSoC DRAM: 256 MB rt2880 uboot v0.00e04 05/25/2006 SERIAL_CLOCK_DIVISOR =16 kaiker,,CONFIG_BAUDRATE =57600 SDRAM SIZE:10000000 Top of RAM usable for U-Boot at: 90000000 Reserving 425k for U-Boot at: 8ff94000 Reserving 1028k for malloc() at: 8fe93000 Reserving 44 Bytes for Board Info at: 8fe92fd4 Reserving 36 Bytes for Global Data at: 8fe92fb0 Reserving 128k for boot params() at: 8fe72fb0 Stack Pointer at: 8fe72f98 relocate_code Pointer at: 8ff94000 Config XHCI 40M PLL Now running in RAM - U-Boot at: 8ff94000 monitor_flash_len =116812 Command "mdio": 0xa0206984 => 0x8ff9a984 Command "nand": 0xa020c2bc => 0x8ffa02bc Command "reset": 0xa0215cec => 0x8ffa9cec Command "go": 0xa020dc68 => 0x8ffa1c68 Command "bootm": 0xa020e4c4 => 0x8ffa24c4 Command "loadb": 0xa020f184 => 0x8ffa3184 Command "tftpboot": 0xa020f7b4 => 0x8ffa37b4 Command "nm": 0xa020fe40 => 0x8ffa3e40 Command "mm": 0xa020fea4 => 0x8ffa3ea4 Command "md": 0xa020ff08 => 0x8ffa3f08 Command "saveenv": 0xa0210480 => 0x8ffa4480 Command "setenv": 0xa0210df0 => 0x8ffa4df0 Command "printenv": 0xa02104d0 => 0x8ffa44d0 Command "?": 0xa02110c4 => 0x8ffa50c4 Command "help": 0xa02110c4 => 0x8ffa50c4 Command "version": 0xa0210f84 => 0x8ffa4f84 Command "sc_boot": 0xa0213d30 => 0x8ffa7d30 Command "sc_nand": 0xa0213d68 => 0x8ffa7d68 Command "sc_eth_test": 0xa0213da4 => 0x8ffa7da4 Command "sc_phy": 0xa0213de0 => 0x8ffa7de0 Command "sc_time": 0xa0213e1c => 0x8ffa7e1c Command "sc_btver": 0xa0213e54 => 0x8ffa7e54 Command "sc_fl_map": 0xa0213e90 => 0x8ffa7e90 Command "sc_endian": 0xa0213ecc => 0x8ffa7ecc Command "sc_gpio": 0xa0213f08 => 0x8ffa7f08 Command "sc_led": 0xa0213f44 => 0x8ffa7f44 Command "sc_dl": 0xa0213f80 => 0x8ffa7f80 Allocate 16 byte aligned buffer: 8ffca410 Enable NFI Clock # MTK NAND # : Use HW ECC NAND ID [C2 F1 80 95 02] Device found in MTK table, ID: c2f1, EXT_ID: 809502 Support this Device in MTK table! c2f1 select_chip [NAND]select ecc bit:4, sparesize :64 spare_per_sector=16 Signature matched and data read! load_fact_bbt success 1023 load fact bbt success [mtk_nand] probe successfully! mtd->writesize=2048 mtd->oobsize=64, mtd->erasesize=131072 devinfo.iowidth=8 icache: sets:256, ways:4, linesz:32 ,total:32768 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 880 MHZ #### estimate memory size =256 Mbytes #Reset_MT7530 set LAN/WAN WLLLL Load Standalone from 40000 SC_DEBUG: Nand Partition Table Magic Found at 100000. ****************************************** Uboot StandAlone Entry ****************************************** GPIO init ********************************************************* Press any key to enter Boot Command Interface ********************************************************* 0 SC_DEBUG: Nand Partition Table Magic Found at 100000. ****************************************** Uboot StandAlone Entry ****************************************** *************************************************** Boot Version 0.2.1.0, at Mar 4 2020, 17:12:13 *************************************************** SC_DEBUG: Nand Partition Table Magic Found at 100000. Entering Firmware : Everything is OK. ************************************* Boot Flag : Sercomm1▒ ************************************* Fw header Magic check OK! FW header checksum should: 0x097261cf, crc32 result: 0x097261cf, Fw header CRC check OK! kernel : real offset: 0x00a00100, data length: 0x002c4fe8,checksum :0xf716e1b5 kernel result: 0xf716e1b5, kernel check sum ok! rootfs: real offset: 0x03000000, data length: 0x00000004, checksum :0x2d55fc1c rootfs result: 0x2d55fc1c, rootfs check sum ok! Kernel Addr : 0xbca00100 ## Booting image at bca00100 ... Image Name: MIPS OpenWrt Linux-5.10.162 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2903976 Bytes = 2.8 MB Load Address: 81001000 Entry Point: 81001000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK kernel addr :0xBCA00100 No initrd ## Transferring control to Linux (at address 81001000) ... ## Giving linux memsize in MB, 256 Starting kernel ... OpenWrt kernel loader for MIPS based SoC Copyright (C) 2011 Gabor Juhos <juhosg@openwrt.org> Decompressing kernel... done! Starting kernel at 80001000... [ 0.000000] Linux version 5.10.162 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 11.3.0 r21714-9ac377d0e0) 11.3.0, GNU ld (GNU Binutils) 2.39) #0 SMP Sat Jan 7 00:32:58 2023 [ 0.000000] SoC Type: MediaTek MT7621 ver:1 eco:3 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001992f (MIPS 1004Kc) [ 0.000000] MIPS: machine is Etisalat S3 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] percpu: Embedded 15 pages/cpu s30480 r8192 d22768 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64960 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00053ed8 [ 0.000000] Readback ErrCtl register=00053ed8 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 248716K/262144K available (7058K kernel code, 632K rwdata, 1420K rodata, 1244K init, 243K bss, 13428K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 880MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0xcaf478abb4, max_idle_ns: 440795247997 ns [ 0.000012] sched_clock: 64 bits at 880MHz, resolution 1ns, wraps every 4398046511103ns [ 0.015862] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 4343773742 ns [ 0.033809] Calibrating delay loop... 586.13 BogoMIPS (lpj=2930688) [ 0.106115] pid_max: default: 32768 minimum: 301 [ 0.115428] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.129831] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.148014] rcu: Hierarchical SRCU implementation. [ 0.157813] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.173364] smp: Bringing up secondary CPUs ... [ 0.183074] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.183083] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.183094] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.183166] CPU1 revision is: 0001992f (MIPS 1004Kc) [ 0.243170] Synchronize counters for CPU 1: done. [ 0.304847] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.304856] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.304864] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.304910] CPU2 revision is: 0001992f (MIPS 1004Kc) [ 0.364021] Synchronize counters for CPU 2: done. [ 0.424367] Primary instruction cache 32kB, VIPT, 4-way, linesize 32 bytes. [ 0.424376] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.424384] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.424433] CPU3 revision is: 0001992f (MIPS 1004Kc) [ 0.483595] Synchronize counters for CPU 3: done. [ 0.543204] smp: Brought up 1 node, 4 CPUs [ 0.555748] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.575259] futex hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.589075] pinctrl core: initialized pinctrl subsystem [ 0.601797] NET: Registered protocol family 16 [ 0.611660] thermal_sys: Registered thermal governor 'step_wise' [ 0.613301] cpuidle: using governor teo [ 0.678398] clocksource: Switched to clocksource GIC [ 0.689848] NET: Registered protocol family 2 [ 0.698899] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.714670] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.731331] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.746470] TCP bind hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.760634] TCP: Hash tables configured (established 2048 bind 2048) [ 0.773385] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.786275] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.800397] NET: Registered protocol family 1 [ 0.808978] PCI: CLS 0 bytes, default 32 [ 0.819376] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.836107] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.847601] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.867892] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 251) [ 0.884256] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.895569] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.906899] mt7621_gpio 1e000600.gpio: registering 32 gpios [ 0.918568] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 0.933898] printk: console [ttyS0] disabled [ 0.942458] 1e000c00.uartlite: ttyS0 at MMIO 0x1e000c00 (irq = 19, base_baud = 3125000) is a 16550A [ 0.960499] printk: console [ttyS0] enabled [ 0.960499] printk: console [ttyS0] enabled [ 0.976997] printk: bootconsole [early0] disabled [ 0.976997] printk: bootconsole [early0] disabled [ 0.996970] 1e000e00.uartlite3: ttyS1 at MMIO 0x1e000e00 (irq = 20, base_baud = 3125000) is a 16550A [ 1.018534] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1 [ 1.031264] nand: Macronix MX30LF1G18AC [ 1.038954] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.054044] mt7621-nand 1e003000.nand: ECC strength adjusted to 4 bits [ 1.124450] scpart: Valid 'SC PART MAP' (10 partitions) found at 0x100000 [ 1.138026] 10 scpart partitions found on MTD device mt7621-nand [ 1.151310] Creating 10 MTD partitions on "mt7621-nand": [ 1.161945] 0x000000000000-0x000000100000 : "u-boot" [ 1.182857] 0x000000100000-0x000000200000 : "dynamic partition map" [ 1.206479] 0x000000200000-0x000000300000 : "Factory" [ 1.227677] 0x000000300000-0x000000400000 : "Boot Flag" [ 1.249135] 0x000000400000-0x000000a00000 : "kernel" [ 1.320800] 0x000000a00000-0x000001000000 : "Kernel 2" [ 1.392610] 0x000001000000-0x000003000000 : "File System 1" [ 1.726489] 0x000003000000-0x000005020000 : "File System 2" [ 2.061147] 0x000005020000-0x000006420000 : "Configuration/log" [ 2.275336] 0x000006420000-0x000007f80000 : "application tmp buffer (Ftool)" [ 2.572040] Concatenating MTD devices: [ 2.579561] (0): "File System 1" [ 2.585974] (1): "Configuration/log" [ 2.593098] (2): "application tmp buffer (Ftool)" [ 2.602458] into device "ubi-concat" [ 2.609640] 1 fixed-partitions partitions found on MTD device ubi-concat [ 2.622983] Creating 1 MTD partitions on "ubi-concat": [ 2.633222] 0x000000000000-0x000004f80000 : "ubi" [ 2.642586] mtd: partition "ubi" extends beyond the end of device "ubi-concat" -- size truncated to 0x4f60000 [ 3.499660] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 3.517138] mtk_soc_eth 1e100000.ethernet eth0: mediatek frame engine at 0xbe100000, irq 22 [ 3.534689] mtk_soc_eth 1e100000.ethernet wan: mediatek frame engine at 0xbe100000, irq 22 [ 3.552543] i2c /dev entries driver [ 3.561887] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 3.575291] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 3.592840] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 3.609142] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 3.625519] mt7621-pci 1e140000.pcie: Parsing DT failed [ 3.637988] NET: Registered protocol family 10 [ 3.648933] Segment Routing with IPv6 [ 3.656321] NET: Registered protocol family 17 [ 3.665280] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 3.691532] 8021q: 802.1Q VLAN Support v1.8 [ 3.703333] mt7530 mdio-bus:1f: MT7530 adapts as multi-chip module [ 3.732334] mt7530 mdio-bus:1f lan1 (uninitialized): PHY [mt7530-0:01] driver [MediaTek MT7530 PHY] (irq=27) [ 3.754433] mt7530 mdio-bus:1f lan2 (uninitialized): PHY [mt7530-0:02] driver [MediaTek MT7530 PHY] (irq=28) [ 3.776417] mt7530 mdio-bus:1f lan3 (uninitialized): PHY [mt7530-0:03] driver [MediaTek MT7530 PHY] (irq=29) [ 3.798516] mt7530 mdio-bus:1f lan4 (uninitialized): PHY [mt7530-0:04] driver [MediaTek MT7530 PHY] (irq=30) [ 3.820875] mt7530 mdio-bus:1f: configuring for fixed/rgmii link mode [ 3.837672] DSA: tree 0 setup [ 3.843916] rt2880-pinmux pinctrl: pcie is already enabled [ 3.854930] mt7621-pci 1e140000.pcie: host bridge /pcie@1e140000 ranges: [ 3.868288] mt7621-pci 1e140000.pcie: No bus range found for /pcie@1e140000, using [bus 00-ff] [ 3.885822] mt7621-pci 1e140000.pcie: MEM 0x0060000000..0x006fffffff -> 0x0000000000 [ 3.902117] mt7621-pci 1e140000.pcie: IO 0x001e160000..0x001e16ffff -> 0x0000000000 [ 3.918494] mt7621-pci-phy 1e149000.pcie-phy: PHY for 0xbe149000 (dual port = 1) [ 3.933575] mt7621-pci-phy 1e14a000.pcie-phy: PHY for 0xbe14a000 (dual port = 0) [ 3.948596] mt7621-pci 1e140000.pcie: failed to parse bus ranges property: -22 [ 4.063120] mt7621-pci-phy 1e149000.pcie-phy: Xtal is 40MHz [ 4.074232] mt7621-pci-phy 1e14a000.pcie-phy: Xtal is 40MHz [ 4.185460] mt7621-pci 1e140000.pcie: pcie2 no card, disable it (RST & CLK) [ 4.199328] mt7621-pci 1e140000.pcie: PCIE0 enabled [ 4.209037] mt7621-pci 1e140000.pcie: PCIE1 enabled [ 4.218748] mt7621-pci 1e140000.pcie: PCI coherence region base: 0x60000000, mask/settings: 0xf0000002 [ 4.237428] mt7621-pci 1e140000.pcie: PCI host bridge to bus 0000:00 [ 4.250117] pci_bus 0000:00: root bus resource [io 0x1e160000-0x1e16ffff] [ 4.263813] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] [ 4.277499] pci_bus 0000:00: root bus resource [bus 00-ff] [ 4.288428] pci_bus 0000:00: root bus resource [mem 0x60000000-0x6fffffff] (bus address [0x00000000-0x0fffffff]) [ 4.308743] pci 0000:00:00.0: [0e8d:0801] type 01 class 0x060400 [ 4.320717] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 4.333198] pci 0000:00:00.0: reg 0x14: initial BAR value 0x00000000 invalid [ 4.347225] pci 0000:00:00.0: reg 0x14: [mem size 0x00010000] [ 4.358733] pci 0000:00:00.0: supports D1 [ 4.366701] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 4.378825] pci 0000:00:01.0: [0e8d:0801] type 01 class 0x060400 [ 4.390841] pci 0000:00:01.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 4.403325] pci 0000:00:01.0: reg 0x14: initial BAR value 0x00000000 invalid [ 4.417354] pci 0000:00:01.0: reg 0x14: [mem size 0x00010000] [ 4.428873] pci 0000:00:01.0: supports D1 [ 4.436842] pci 0000:00:01.0: PME# supported from D0 D1 D3hot [ 4.449988] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 4.465953] pci 0000:00:01.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 4.482158] pci 0000:01:00.0: [14c3:7615] type 00 class 0x000280 [ 4.494186] pci 0000:01:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 4.508229] pci 0000:01:00.0: reg 0x10: [mem size 0x00100000 64bit] [ 4.520882] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s PCIe x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5.0 GT/s PCIe x1 link) [ 4.552202] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 4.562643] pci 0000:00:00.0: bridge window [io 0x0000-0x0fff] [ 4.574778] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 4.588291] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff pref] [ 4.602684] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 4.616128] pci 0000:02:00.0: [14c3:7603] type 00 class 0x028000 [ 4.628140] pci 0000:02:00.0: reg 0x10: initial BAR value 0x00000000 invalid [ 4.642183] pci 0000:02:00.0: reg 0x10: [mem size 0x00100000] [ 4.653767] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold [ 4.667499] pci 0000:00:01.0: PCI bridge to [bus 02-ff] [ 4.677951] pci 0000:00:01.0: bridge window [io 0x0000-0x0fff] [ 4.690090] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff] [ 4.703610] pci 0000:00:01.0: bridge window [mem 0x60000000-0x600fffff pref] [ 4.717991] pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 02 [ 4.731241] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 4.744409] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 4.758268] pci 0000:00:01.0: BAR 0: no space for [mem size 0x80000000] [ 4.771443] pci 0000:00:01.0: BAR 0: failed to assign [mem size 0x80000000] [ 4.785303] pci 0000:00:00.0: BAR 8: assigned [mem 0x60000000-0x600fffff] [ 4.798834] pci 0000:00:00.0: BAR 9: assigned [mem 0x60100000-0x601fffff pref] [ 4.813214] pci 0000:00:01.0: BAR 8: assigned [mem 0x60200000-0x602fffff] [ 4.826738] pci 0000:00:01.0: BAR 9: assigned [mem 0x60300000-0x603fffff pref] [ 4.841124] pci 0000:00:00.0: BAR 1: assigned [mem 0x60400000-0x6040ffff] [ 4.854658] pci 0000:00:01.0: BAR 1: assigned [mem 0x60410000-0x6041ffff] [ 4.868184] pci 0000:00:00.0: BAR 7: assigned [io 0x1e160000-0x1e160fff] [ 4.881710] pci 0000:00:01.0: BAR 7: assigned [io 0x1e161000-0x1e161fff] [ 4.895240] pci 0000:01:00.0: BAR 0: assigned [mem 0x60000000-0x600fffff 64bit] [ 4.909810] pci 0000:00:00.0: PCI bridge to [bus 01] [ 4.919703] pci 0000:00:00.0: bridge window [io 0x1e160000-0x1e160fff] [ 4.933219] pci 0000:00:00.0: bridge window [mem 0x60000000-0x600fffff] [ 4.946739] pci 0000:00:00.0: bridge window [mem 0x60100000-0x601fffff pref] [ 4.961129] pci 0000:02:00.0: BAR 0: assigned [mem 0x60200000-0x602fffff] [ 4.974657] pci 0000:00:01.0: PCI bridge to [bus 02] [ 4.984548] pci 0000:00:01.0: bridge window [io 0x1e161000-0x1e161fff] [ 4.998063] pci 0000:00:01.0: bridge window [mem 0x60200000-0x602fffff] [ 5.011585] pci 0000:00:01.0: bridge window [mem 0x60300000-0x603fffff pref] [ 5.029881] UBI: auto-attach mtd10 [ 5.036677] ubi0: attaching mtd10 [ 5.043655] mt7530 mdio-bus:1f: Link is Up - 1Gbps/Full - flow control rx/tx [ 6.648721] ubi0: scanning is finished [ 6.672992] ubi0: attached mtd10 (name "ubi", size 79 MiB) [ 6.683982] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 6.697671] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 6.711202] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 6.725063] ubi0: good PEBs: 635, bad PEBs: 0, corrupted PEBs: 0 [ 6.737024] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 [ 6.751410] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 354328867 [ 6.769439] ubi0: available PEBs: 0, total reserved PEBs: 635, PEBs reserved for bad PEB handling: 13 [ 6.787833] ubi0: background thread "ubi_bgt0d" started, PID 489 [ 6.790304] block ubiblock0_0: created from ubi0:0(rootfs) [ 6.810823] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 6.831772] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 6.850114] Freeing unused kernel memory: 1244K [ 6.859187] This architecture does not have kernel memory protection. [ 6.872027] Run /sbin/init as init process [ 7.353538] init: Console is alive [ 7.360777] init: - watchdog - [ 8.173055] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 8.235362] usbcore: registered new interface driver usbfs [ 8.246481] usbcore: registered new interface driver hub [ 8.257223] usbcore: registered new device driver usb [ 8.278309] xhci-mtk 1e1c0000.xhci: supply vbus not found, using dummy regulator [ 8.293381] xhci-mtk 1e1c0000.xhci: supply vusb33 not found, using dummy regulator [ 8.308733] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 8.319369] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 1 [ 8.348589] xhci-mtk 1e1c0000.xhci: hcc params 0x01401198 hci version 0x96 quirks 0x0000000000290010 [ 8.366883] xhci-mtk 1e1c0000.xhci: irq 21, io mem 0x1e1c0000 [ 8.379683] hub 1-0:1.0: USB hub found [ 8.387302] hub 1-0:1.0: 2 ports detected [ 8.395959] xhci-mtk 1e1c0000.xhci: xHCI Host Controller [ 8.406673] xhci-mtk 1e1c0000.xhci: new USB bus registered, assigned bus number 2 [ 8.421653] xhci-mtk 1e1c0000.xhci: Host supports USB 3.0 SuperSpeed [ 8.434530] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 8.451593] hub 2-0:1.0: USB hub found [ 8.459234] hub 2-0:1.0: 1 port detected [ 8.474663] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 8.498790] init: - preinit - [ 9.266446] random: jshn: uninitialized urandom read (4 bytes read) [ 9.388244] random: jshn: uninitialized urandom read (4 bytes read) [ 9.438952] random: jshn: uninitialized urandom read (4 bytes read) [ 9.759679] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 9.775799] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 9.778956] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 9.806136] 8021q: adding VLAN 0 to HW filter on device lan1 [ 9.820081] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 12.022623] UBIFS (ubi0:1): Mounting in unauthenticated mode [ 12.034320] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 631 [ 12.114641] UBIFS (ubi0:1): recovery needed [ 12.310004] UBIFS (ubi0:1): recovery completed [ 12.318989] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" [ 12.334585] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 12.354331] UBIFS (ubi0:1): FS size: 73011200 bytes (69 MiB, 575 LEBs), journal size 3682304 bytes (3 MiB, 29 LEBs) [ 12.375114] UBIFS (ubi0:1): reserved for root: 3448499 bytes (3367 KiB) [ 12.388285] UBIFS (ubi0:1): media format: w5/r0 (latest is w5/r0), UUID 5A0BB14D-DD9F-49F5-B3A8-401D476EE4B2, small LPT model [ 12.416992] mount_root: switching to ubifs overlay [ 12.444873] urandom-seed: Seeding with /etc/urandom.seed [ 12.552508] procd: - early - [ 12.558692] procd: - watchdog - [ 13.168591] procd: - watchdog - [ 13.175514] procd: - ubus - [ 13.263369] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.278012] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.291238] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.310593] procd: - init - Please press Enter to activate this console. [ 13.915440] kmodloader: loading kernel modules from /etc/modules.d/* [ 14.101600] urngd: v1.0.2 started. [ 14.119724] Loading modules backported from Linux version v6.1-rc8-0-g76dcd734eca2 [ 14.134828] Backport generated by backports.git v5.15.81-1-41-g02e352527db5 [ 14.298033] random: crng init done [ 14.304890] random: 31 urandom warning(s) missed due to ratelimiting [ 14.349451] mt7621-pci 1e140000.pcie: bus=2 slot=1 irq=24 [ 14.360310] pci 0000:00:01.0: enabling device (0004 -> 0007) [ 14.371612] mt7603e 0000:02:00.0: enabling device (0000 -> 0002) [ 14.383764] mt7603e 0000:02:00.0: ASIC revision: 76030010 [ 15.419802] mt7603e 0000:02:00.0: Firmware Version: ap_pcie [ 15.430942] mt7603e 0000:02:00.0: Build Time: 20160107100755 [ 15.478415] mt7603e 0000:02:00.0: firmware init done [ 15.667266] mt7621-pci 1e140000.pcie: bus=1 slot=0 irq=23 [ 15.678120] pci 0000:00:00.0: enabling device (0004 -> 0007) [ 15.689425] mt7615e 0000:01:00.0: enabling device (0000 -> 0002) [ 15.772327] PPP generic driver version 2.4.2 [ 15.782611] NET: Registered protocol family 24 [ 15.801121] kmodloader: done loading kernel modules from /etc/modules.d/* [ 15.836932] mt7615e 0000:01:00.0: HW/SW Version: 0x8a108a10, Build Time: 20180518100604a [ 15.836932] [ 16.159517] mt7615e 0000:01:00.0: N9 Firmware Version: _reserved_, Build Time: 20200814163649 [ 16.293311] mt7615e 0000:01:00.0: CR4 Firmware Version: _reserved_, Build Time: 20190415154149 [ 23.065957] mtk_soc_eth 1e100000.ethernet eth0: Link is Down [ 23.086933] mtk_soc_eth 1e100000.ethernet eth0: configuring for fixed/rgmii link mode [ 23.102949] mtk_soc_eth 1e100000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 23.106492] mt7530 mdio-bus:1f lan1: configuring for phy/gmii link mode [ 23.133478] 8021q: adding VLAN 0 to HW filter on device lan1 [ 23.147790] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 23.161651] br-lan: port 1(lan1) entered blocking state [ 23.172597] br-lan: port 1(lan1) entered disabled state [ 23.184120] device lan1 entered promiscuous mode [ 23.193661] device eth0 entered promiscuous mode [ 23.232472] mt7530 mdio-bus:1f lan2: configuring for phy/gmii link mode [ 23.246261] 8021q: adding VLAN 0 to HW filter on device lan2 [ 23.261108] br-lan: port 2(lan2) entered blocking state [ 23.271636] br-lan: port 2(lan2) entered disabled state [ 23.283406] device lan2 entered promiscuous mode [ 23.306876] mt7530 mdio-bus:1f lan3: configuring for phy/gmii link mode [ 23.320975] 8021q: adding VLAN 0 to HW filter on device lan3 [ 23.336259] br-lan: port 3(lan3) entered blocking state [ 23.346803] br-lan: port 3(lan3) entered disabled state [ 23.359639] device lan3 entered promiscuous mode [ 23.381229] mt7530 mdio-bus:1f lan4: configuring for phy/gmii link mode [ 23.395122] 8021q: adding VLAN 0 to HW filter on device lan4 [ 23.410763] br-lan: port 4(lan4) entered blocking state [ 23.421303] br-lan: port 4(lan4) entered disabled state [ 23.433390] device lan4 entered promiscuous mode [ 23.462112] mtk_soc_eth 1e100000.ethernet wan: PHY [mdio-bus:00] driver [MediaTek MT7530 PHY] (irq=POLL) [ 23.481079] mtk_soc_eth 1e100000.ethernet wan: configuring for phy/rgmii link mode [ 25.578659] mtk_soc_eth 1e100000.ethernet wan: Link is Up - 100Mbps/Full - flow control rx/tx [ 25.595703] IPv6: ADDRCONF(NETDEV_CHANGE): wan: link becomes ready [ 25.911483] mt7530 mdio-bus:1f lan3: Link is Up - 1Gbps/Full - flow control rx/tx [ 25.926590] br-lan: port 3(lan3) entered blocking state [ 25.937059] br-lan: port 3(lan3) entered forwarding state [ 25.949232] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready BusyBox v1.35.0 (2023-01-07 00:32:58 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r21714-9ac377d0e0 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/02/12 10:03
  • by 127.0.0.1