Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision Next revisionBoth sides next revision | ||
| inbox:toh:netgear:rbr20 [2024/10/25 15:38] – [Netgear RBR20] ivanolo | inbox:toh:netgear:rbr20 [2024/10/25 22:07] – [Table] ivanolo | ||
|---|---|---|---|
| Line 20: | Line 20: | ||
| - | /*** if info available: uncomment and fill in | + | |
| ===== Supporting activities ===== | ===== Supporting activities ===== | ||
| - | //Describe if there are any ongoing activities that might lead to OpenWrt support.// | + | OpenWrt forum thread: https://forum.openwrt.org/t/ipq4019-support-for-netgear-orbi-rbr20-rbs20/213897 |
| - | + | ||
| - | * OpenWrt forum thread: (add link) | + | |
| - | ***/ | + | |
| /*** if info available: uncomment and fill in | /*** if info available: uncomment and fill in | ||
| Line 42: | Line 38: | ||
| ===== Hardware highlights ===== | ===== Hardware highlights ===== | ||
| - | ^ Model | Orbi RBR20 | | + | ^ Brand | Netgear |
| - | ^ CPU | Qualcomm IPQ4019 | + | ^ Model | RBR20 | |
| - | ^ CPU MHz | 716 | | + | ^ Version |
| - | ^ CPU Cores | 4 | + | ^ CPU | Qualcomm IPQ4019 |
| - | ^ RAM MB | 512 | + | ^ CPU MHz | 717 | |
| - | ^ Flash 1 MB | 256 | + | ^ CPU Cores | 4 |
| - | ^ Flash 2 MB | 16 | | + | ^ RAM MB | 512 |
| - | ^ WLAN Hardware | + | ^ Flash 1 MB | 256 |
| - | ^ WLAN 2.4GHz | + | ^ Flash 2 MB | 16 | |
| - | ^ WLAN 5GHz | a/ | + | ^ WLAN Hardware |
| - | ^ Ethernet 100M Ports | - | + | ^ WLAN 2.4GHz |
| - | ^ Ethernet 1G Ports | 2 | + | ^ WLAN 5GHz | a/ |
| - | ^ Modem | - | + | ^ Switch Hardware |
| - | ^ USB Ports | - | + | ^ Ethernet 100M Ports | - |
| + | ^ Ethernet 1G Ports | 2 | ||
| + | ^ Modem | - | ||
| + | ^ USB Ports | - | ||
| Line 121: | Line 120: | ||
| - | ===== Hardware ===== | + | /*** ===== Hardware ===== |
| ==== Info ==== | ==== Info ==== | ||
| ^ Architecture | ^ Architecture | ||
| Line 137: | Line 136: | ||
| ^ Serial | ^ Serial | ||
| ^ JTAG | EXAMPLE [[#JTAG|Not populated]] | ^ JTAG | EXAMPLE [[#JTAG|Not populated]] | ||
| + | ***/ | ||
| /*** if info available: uncomment and fill in | /*** if info available: uncomment and fill in | ||
| Line 155: | Line 154: | ||
| /* Thanks, your wiki administration - Oct. 2015 */ | /* Thanks, your wiki administration - Oct. 2015 */ | ||
| - | **Insert photo of front of the casing** | + | **Disassembly Steps 1-2-3** |
| - | **Insert photo of back of the casing** | + | {{: |
| - | **Insert photo of backside label** | + | **Disassembly Step 4** |
| - | **Insert photo of PCB** | + | {{: |
| - | ==== Opening the case ==== | + | **Disassembly Steps 5-6** |
| - | <WRAP BOX> | + | {{: |
| - | FIXME //Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, | + | |
| - | </ | + | **Disassembly Step 7** |
| + | |||
| + | {{: | ||
| + | |||
| + | **Disassembly Step 8 (Front)** | ||
| + | |||
| + | {{: | ||
| + | |||
| + | **Disassembly Step 8 (Back)** | ||
| + | |||
| + | {{: | ||
| + | |||
| + | **Front PCB Detail** | ||
| + | |||
| + | {{: | ||
| + | |||
| + | **Back PCB Detail** | ||
| + | |||
| + | {{: | ||
| + | |||
| + | **Flash Detail** | ||
| + | |||
| + | {{: | ||
| + | |||
| + | **Antenna Detail** | ||
| + | |||
| + | {{: | ||
| + | |||
| + | **Switch Detail** | ||
| + | |||
| + | {{: | ||
| + | ==== Opening the case ==== | ||
| + | - Peel off bottom label and remove rubber feet on either side | ||
| + | - Peel off rear label for the interfaces | ||
| + | - Remove rear screws | ||
| + | - Separate front and rear shell | ||
| + | - Disconnect antennas | ||
| + | - Remove motherboard from shell | ||
| + | - Remove screws clamping heatsinks together | ||
| + | - Remove motherboard shields (shield covering the switch chip will need to be broken) | ||
| ==== Serial ==== | ==== Serial ==== | ||
| -> [[docs: | -> [[docs: | ||