User Tools

Site Tools


inbox:toh:netgear:netgear_wndr4300_2

Netgear WNDR4300 v2

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

Rev 2 of the WNDR4300 uses the same board as the WNDR4500v3

Generic Router

OpenWrt support

Not supported. Member vreppeto is currently working on it. If you want to help please let me know.

Supporting activities

Hardware highlights

CPU Ram Flash Network WLAN 2G WLAN 5G USB Serial JTag
QCA9563 @ 750 MHz 128 MiB 128 MiB 1 WAN + 4x LAN (GBit) b/g/n a/n 1x 2.0 Yes Yes

Installation

Hardware

Info

Architecture MIPS
Vendor Qualcomm/Atheros
Bootloader U-Boot
System-On-Chip QCA9563 - MIPS 74Kc V5.0
CPU/Speed 750 MHz
Flash-Chip EXAMPLE unkown
Flash size 128 MiB
RAM 128 MiB
Wireless QCA9563 2.4GHz 2×2 802.11bgn
Wireless QCA9580 5.4GHz 3×3 802.11an
Ethernet 10/100/1000 Mbit/s w/ vlan support
USB 1x 2.0
Serial Yes
JTAG Not populated

Photos

Insert photo of front of the casing

Insert photo of back of the casing

Insert photo of backside label

Insert photo of PCB

Opening the case

The rubber feet must be removed from the bottom and an extremely small torx driver is the correct tool for removing the screws. A flat scredriver filed to just the right width will also work.

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

FIXME Replace EXAMPLE by real values.

Serial connection parameters
for Netgear WNDR4300 2
115200, 8N1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootlogs

OEM bootlog

U-Boot 1.1.4 (Aug 12 2014 - 15:21:46) U-boot dni29 V0.5 for DNI HW ID: 29764821 NOR flash 2MB NAND flash 128MB RAM 12B - Dragonfly 1.0DRAM: sri ath_ddr_initial_config(278): (ddr2 init) ath_sys_frequency: cpu 775 ddr 650 ahb 258 Tap values = (0x10, 0x10, 0x10, 0x10) 128 MB Top of RAM usable for U-Boot at: 88000000 Reserving 265k for U-Boot at: 87fbc000 Reserving 192k for malloc() at: 87f8c000 Reserving 44 Bytes for Board Info at: 87f8bfd4 Reserving 36 Bytes for Global Data at: 87f8bfb0 Reserving 128k for boot params() at: 87f6bfb0 Stack Pointer at: 87f6bf98 Now running in RAM - U-Boot at: 87fbc000 Flash Manuf Id 0xc2, DeviceId0 0x20, DeviceId1 0x15 flash size 2MB, sector count = 32 Flash: 2 MB Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014 Qualcomm Atheros Inc. ath_parse_read_id: SPI NAND V.Id: 0xc8 D.Id: 0xf1 ====== NAND Parameters ====== sc = 0x87ff77e4 page = 0x800 block = 0x20000In: serial Out: serial Err: serial Net: ath_gmac_enet_initialize... Fetching MAC Address from 0x87fe914c ath_gmac_enet_initialize: reset mask:c02200 athr_mgmt_init ::done Dragonfly ----> S17 PHY * athrs17_reg_init: complete SGMII in forced mode athr_gmac_sgmii_setup SGMII done : cfg1 0x80000000 cfg2 0x7114 eth0: a0:63:91:a0:d6:02 eth0 up eth0 Setting 0x181162c0 to 0x40802100 Hit any key to stop autoboot: 0 Trying eth0 eth0 link down FAIL Client starts...[Listening] for ADVERTISE...TTT Retry count exceeded; boot the image as usual nmrp server is stopped or failed ! Loading from device 0: ath-spi-nand (offset 0x0) ** check kernel image ** Verifying Checksum ... OK ** check rootfs image ** Verifying Checksum ... OK ## Booting image at 81000000 ... Image Name: MIPS OpenWrt Linux-2.6.31 Created: 2015-07-08 3:51:58 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1166769 Bytes = 1.1 MB Load Address: 80002000 Entry Point: 802809b0 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 802809b0) ... ## Giving linux memsize in bytes, 134217728 Starting kernel ... Booting QCA956x Linux version 2.6.31 (root@dnixm-compiler3) (gcc version 4.3.3 (GCC) ) #1 Wed J5 flash_size passed from bootloader = 2 CPU revision is: 00019750 (MIPS 74Kc) ath_sys_frequency: cpu 775 ddr 650 ahb 258 Determined physical RAM map: memory: 08000000 @ 00000000 (usable) Initrd not found or empty - disabling initrd Zone PFN ranges: Normal 0x00000000 -> 0x00008000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00008000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 32512 Kernel command line: console=ttyS0,115200 rootfstype=squashfs board=WNDR4500v3 ) PID hash table entries: 512 (order: 9, 2048 bytes) Dentry cache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cache hash table entries: 8192 (order: 3, 32768 bytes) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes Writing ErrCtl register=00000000 Readback ErrCtl register=00000000 Memory: 126236k/131072k available (2586k kernel code, 4652k reserved, 673k data) SLUB: Genslabs=13, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 NR_IRQS:128 plat_time_init: plat time init done r4k_clockevent_init: Ignoring int_usable failure Calibrating delay loop... 387.07 BogoMIPS (lpj=774144) Mount-cache hash table entries: 512 NET: Registered protocol family 16 ath_pcibios_init: bus 0 ath_pcibios_init(254): PCI 0 CMD write: 0x356 registering PCI controller with io_map_base unset bio: create slab <bio-0> at 0 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb pci 0000:00:00.0: PME# supported from D0 D1 D3hot pci 0000:00:00.0: PME# disabled pcibios_map_irq: IRQ 76 for bus 0 NET: Registered protocol family 2 create ipmac proc IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 4096 (order: 3, 32768 bytes) TCP bind hash table entries: 4096 (order: 2, 16384 bytes) TCP: Hash tables configured (established 4096 bind 4096) TCP reno registered NET: Registered protocol family 1 ATH GPIOC major 0 squashfs: version 4.0 (2009/01/31) Phillip Lougher JFFS2 version 2.2 (NAND) (ZLIB) (RTIME) (c) 2001-2006 Red Hat, Inc. msgmni has been set to 246 io scheduler noop registered io scheduler deadline registered (default) Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled serial8250.0: ttyS0 at MMIO 0xb8020000 (irq = 19) is a 16550A console [ttyS0] enabled tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> usbcore: registered new interface driver cdc_ether 8 cmdlinepart partitions found on MTD device ath-nor0 Creating 8 MTD partitions on "ath-nor0": 0x000000000000-0x000000040000 : "u-boot" 0x000000040000-0x000000050000 : "u-boot-env" 0x000000050000-0x000000060000 : "caldata_backup" 0x000000060000-0x000000070000 : "config" 0x000000070000-0x000000080000 : "traffic_meter" 0x000000080000-0x000000090000 : "pot" 0x000000090000-0x0000001f0000 : "reserved" 0x0000001f0000-0x000000200000 : "caldata" Qualcomm Atheros SPI NAND Driver, Version 0.1 (c) 2014 Qualcomm Atheros Inc. ath_parse_read_id: SPI NAND V.Id: 0xc8 D.Id: 0xf1 6 cmdlinepart partitions found on MTD device ath-spi-nand Creating 6 MTD partitions on "ath-spi-nand": 0x000000000000-0x000000120000 : "kernel" 0x000000120000-0x000001900000 : "rootfs" mtd: find squashfs magic at 0x120000 of "ath-spi-nand" the correct location of partition "rootfs": 0x000000120000-0x000001900000 mtd: partition "rootfs" set to be root filesystem mtd: partition "rootfs_data" created automatically, ofs=DA0000, len=B60000 0x000000da0000-0x000001900000 : "rootfs_data" 0x000000000000-0x000001900000 : "firmware" 0x000001900000-0x000001b00000 : "language" 0x000001b00000-0x000001b20000 : "mtdoops" 0x000001b20000-0x000008000000 : "reserved" ====== NAND Parameters ====== sc = 0x87875800 page = 0x800 block = 0x20000 ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver Port Status 1c000004 ath-ehci ath-ehci.0: ATH EHCI ath-ehci ath-ehci.0: new USB bus registered, assigned bus number 1 ehci_reset Intialize USB CONTROLLER in host mode: 13 ehci_reset Port Status 1c000000 ath-ehci ath-ehci.0: irq 3, io mem 0x1b000000 ehci_reset Intialize USB CONTROLLER in host mode: 13 ehci_reset Port Status 1c000000 ath-ehci ath-ehci.0: USB 2.0 started, EHCI 1.00 usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb1: Product: ATH EHCI usb usb1: Manufacturer: Linux 2.6.31 ehci_hcd usb usb1: SerialNumber: platform usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected Port Status 1c000000 ath-ehci1 ath-ehci1.1: ATH EHCI ath-ehci1 ath-ehci1.1: new USB bus registered, assigned bus number 2 ehci_reset Intialize USB CONTROLLER in host mode: 13 ehci_reset Port Status 1c000000 ath-ehci1 ath-ehci1.1: irq 3, io mem 0x1b400000 ehci_reset Intialize USB CONTROLLER in host mode: 13 ehci_reset Port Status 1c000000 ath-ehci1 ath-ehci1.1: USB 2.0 started, EHCI 1.00 usb usb2: New USB device found, idVendor=1d6b, idProduct=0002 usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 usb usb2: Product: ATH EHCI usb usb2: Manufacturer: Linux 2.6.31 ehci_hcd usb usb2: SerialNumber: platform usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. Netfilter messages via NETLINK v0.30. NAT Session Management application ports priority table is loaded! nf_conntrack version 0.5.0 (2048 buckets, 8192 max) ip_tables: (C) 2000-2006 Netfilter Core Team TCP cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 Ebtables v2.0 registered 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> arch/mips/atheros/gpio.c (ath_simple_config_init) JUMPSTART_GPIO: 12 arch/mips/atheros/gpio.c (ath_simple_config_init) ATH_S17INT_GPIO: 10 athwdt_init: Registering WDT success VFS: Mounted root (squashfs filesystem) readonly on device 31:9. Freeing unused kernel memory: 152k freed Please be patient, while OpenWrt loads ... usb 1-1: new high speed USB device using ath-ehci and address 2 usb 1-1: New USB device found, idVendor=1f75, idProduct=0916 usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-1: Product: IS916 usb 1-1: Manufacturer: Patriot Memory usb 1-1: SerialNumber: 09161000000411491100000472 usb 1-1: configuration #1 chosen from 1 choice scsi0 : SCSI emulation for USB Mass Storage devices - init - init started: BusyBox v1.4.2 (2015-07-08 11:22:00 CST) multi-call binary Loading data from /dev/mtd3 ... Done! The data center is Running ... mobiled deamon is running background... board parameter in mtd7 and mtd2 partition are same and valid The region number is: 0x0001 REGION: NA usb 1-1: USB disconnect, address 2 PPP generic driver version 2.4.2 dni-lan-qos module init. dni-qos module init. NET: Registered protocol family 24 nf_nat_STARCRAFT: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint nf_conntrack_rtsp v0.6.21 loading nf_nat_rtsp v0.6.21 loading nf_conntrack_proto_esp loaded NET: Registered protocol family 27 PPPoL2TP kernel driver, V0.16.1 PPTP-GRE-v1.13 2007 (C) Delta Networks Inc. qca956x_GMAC: Length per segment 1536 956x_GMAC: qca956x_gmac_attach 956x_GMAC: qca956x_set_gmac_caps Currently in interrupt mode unit0 qca956x_set_gmac_caps CHECK DMA STATUS mac:0 Registering S17.... qca956x_GMAC: RX TASKLET - Pkts per Intr:160 qca956x_GMAC: Mac address for unit 0:bf1f0000 qca956x_GMAC: a0:63:91:a0:d6:02 qca956x_GMAC: Max segments per packet : 1 qca956x_GMAC: Max tx descriptor count : 128 qca956x_GMAC: Max rx descriptor count : 224 qca956x_GMAC: Mac capability flags : 12002401 956x_GMAC: Serdes PLL is locked value 0x1b838116 usbcore: registered new interface driver cdc_acm cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adaptes usbcore: registered new interface driver usbserial USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic usbserial: USB Serial Driver core Generating Rules... Done! SN: 3XB1585304315 WAN MAC: a0:63:91:a0:D6:03 LAN MAC: a0:63:91:a0:D6:02 WLA MAC: a0:63:91:a0:D6:04 The region number is: 0x0001 REGION: NA client bridge loaded cp: cannot stat '/etc/wpa2.orig/*': No such file or directory To set s17 LOOKUP_CTRL_REG registers, flag 0 athr_gmac_ring_alloc Allocated 2048 at 0x870fb000 sram_desc_cnt 1536,mac Unit 0,Tx r->ring_desc 0xbd000000 athr_gmac_ring_alloc Allocated 3584 at 0x870ed000 sram_desc_cnt 4224,mac Unit 0,Rx r->ring_desc 0xbd000600 956x_GMAC: eth0 in SGMII MODE Dragonfly ----> S17 PHY * ******the ssdk init done value is : 0 athrs17_reg_init:done 955x_SGMII::athr_gmac_sgmii_setup Done Setting Drop CRC Errors, Pause Frames and Length Error frames Setting PHY... Phy setup Complete To set s17 LOOKUP_CTRL_REG registers, flag 1 ADDRCONF(NETDEV_UP): phy0: link is not ready athr_gmac_ring_free Freeing at 0x870fb000 athr_gmac_ring_free Freeing at 0x870ed000 Write Reg: 0x00000620: Oldval = 0x001004f0 Newval = 0x080004f0 Write Reg: 0x00000660: Oldval = 0x0014007e Newval = 0x0014017e Write Reg: 0x0000066c: Oldval = 0x0014007d Newval = 0x0014017d Write Reg: 0x00000678: Oldval = 0x0014007b Newval = 0x0014017b Write Reg: 0x00000684: Oldval = 0x00140077 Newval = 0x00140177 Write Reg: 0x00000690: Oldval = 0x0014006f Newval = 0x0014016f Write Reg: 0x0000069c: Oldval = 0x0014005f Newval = 0x0014015f Write Reg: 0x00000c00: Oldval = 0x00000000 Newval = 0x00000002 Write Reg: 0x00000420: Oldval = 0x00010001 Newval = 0x00010001 Write Reg: 0x00000424: Oldval = 0x00003040 Newval = 0x00002040 Write Reg: 0x00000428: Oldval = 0x00010001 Newval = 0x00010001 Write Reg: 0x0000042c: Oldval = 0x00003040 Newval = 0x00001040 Write Reg: 0x00000430: Oldval = 0x00010001 Newval = 0x00010001 Write Reg: 0x00000434: Oldval = 0x00003040 Newval = 0x00001040 Write Reg: 0x00000438: Oldval = 0x00010001 Newval = 0x00010001 Write Reg: 0x0000043c: Oldval = 0x00003040 Newval = 0x00001040 Write Reg: 0x00000440: Oldval = 0x00010001 Newval = 0x00010001 Write Reg: 0x00000444: Oldval = 0x00003040 Newval = 0x00001040 Write Reg: 0x00000448: Oldval = 0x00010001 Newval = 0x00020001 Write Reg: 0x0000044c: Oldval = 0x00003040 Newval = 0x00001040 Write Reg: 0x00000614: Oldval = 0x00000000 Newval = 0x80000001 Write Reg: 0x00000610: Oldval = 0x00000000 Newval = 0x001bd560 Write Reg: 0x00000614: Oldval = 0x00000001 Newval = 0x80010002 Write Reg: 0x00000610: Oldval = 0x00000000 Newval = 0x001b7fe0 Write Reg: 0x00000614: Oldval = 0x00000002 Newval = 0x80020002 Write Reg: 0x00000624: Oldval = 0x007f7f7f Newval = 0x7f7f7f7f Write Reg: 0x00000210: Oldval = 0x00000000 Newval = 0x06060606 Write Reg: 0x00000214: Oldval = 0x00000000 Newval = 0x01000006 Write Reg: 0x00000030: Oldval = 0x80000705 Newval = 0x80000302 Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x5e7ffffa Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0x00000100 Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000001 Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x00000001 Write Reg: 0x00000400: Oldval = 0x00000000 Newval = 0x80000020 Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0xffffffff Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0x0000ffff Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000fff Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x000000f9 Write Reg: 0x00000400: Oldval = 0x00000020 Newval = 0x80000120 Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0xc0000000 Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000013 Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000400: Oldval = 0x00000120 Newval = 0x80000220 Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0x00003333 Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000001 Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x00000001 Write Reg: 0x00000400: Oldval = 0x00000220 Newval = 0x80000021 Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0x0000ffff Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000fff Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x000000f9 Write Reg: 0x00000400: Oldval = 0x00000021 Newval = 0x80000121 Write Reg: 0x000To set s17 LOOKUP_CTRL_REG registers, flag 0 00404: Oldval = athr_gmac_ring_alloc Allocated 2048 at 0x8719f000 0x00000000 Newvasram_desc_cnt 4224,mac Unit 0,Tx r->ring_desc 0xbd000000 l = 0x00000000 athr_gmac_ring_alloc Allocated 3584 at 0x870ed000 Write Reg: 0x000sram_desc_cnt 4224,mac Unit 0,Rx r->ring_desc 0xbd000600 00408: Oldval = 0x00000000 Newva956x_GMAC: eth0 in SGMII MODE l = 0xc0000000 Dragonfly ----> S17 PHY * Write Reg: 0x000******the ssdk init done value is : 1 0040c: Oldval = 0x00000000 Newval = 0x00000013 Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000400: Oldval = 0x00000121 Newval = 0x80000221 Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0x00003333 Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x0000001e Write Reg: 0x00000400: Oldval = 0x00000221 Newval = 0x80000022 Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0x0000ffff Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x000000c9 Write Reg: 0x00000400: Oldval = 0x00000022 Newval = 0x80000122 Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0xe0000000 Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000013 Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000400: Oldval = 0x00000122 Newval = 0x80000222 Write Reg: 0x00000404: Oldval = 0x00000000 Newva/proc/qca_switch/nf_athrs17_hnad l = 0x00000000 /proc/qca_switch/nf_athrs17_hnat_wan_type is created Write Reg: 0x000/proc/qca_switch/nf_athrs17_hnat_ppp_id is created 00408: Oldval = /proc/qca_switch/nf_athrs17_hnat_udp_thresh is created 0x00000000 Newva/proc/qca_switch/nf_athrs17_hnat_wan_ip is created l = 0x00003333 /proc/qca_switch/nf_athrs17_hnat_ppp_peer_ip is created Write Reg: 0x000/proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created 0040c: Oldval = /proc/qca_switch/nf_athrs17_hnat_wan_mac is created 0x00000000 Newva/proc/qca_switch/nf_athrs17_hnat_ppp_id2 is created l = 0x00000000 /proc/qca_switch/nf_athrs17_hnat_ppp_peer_mac is created Write Reg: 0x000Adding ACL rules 15 - upnp_ssdp_add_acl_rules 00410: Oldval = 0x00000000 Newval = 0x00000002 Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x00000001 Write Reg: 0x00000400: Oldval = 0x00000222 Newval = 0x80000023 Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0x0000ffff Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000000 Adding ACL rules 8 - ipv6_snooping_solicted_node_add_acl_rules Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x000000f9 Write Reg: 0x00000400: Oldval = 0x00000023 Newval = 0x80000123 Write Reg: 0x00000404: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000408: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x0000040c: Oldval = 0x00000000 Newval = 0x00000014 Write Reg: 0x00000410: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000414: Oldval = 0x00000000 Newval = 0x00000000 Write Reg: 0x00000400: Oldval = 0x00000123 Newval = 0x80000223 Adding ACL rules 12 - ipv6_snooping_sextuple0_group_add_acl_rules Adding ACL rules 14 - ipv6_snooping_quintruple0_1_group_add_acl_rules Hello, nat helper module for 1.1! ######## S17 SSDK init succeeded! ######## Error: cannot be initialized twice! athrs17_reg_init:done 955x_SGMII::athr_gmac_sgmii_setup Done Setting Drop CRC Errors, Pause Frames and Length Error frames Setting PHY... Phy setup Complete To set s17 LOOKUP_CTRL_REG registers, flag 1 ADDRCONF(NETDEV_UP): phy0: link is not ready init.enet: Default WAN MAC is : a0:63:91:a0:d6:03 device eth0 entered promiscuous mode device phy0 entered promiscuous mode init.enet: Default LAN MAC is : a0:63:91:a0:d6:02 Loading DNI-ENET driver device pas0 entered promiscuous mode br0: port 1(eth0) entering forwarding state br0: port 1(eth0) entering disabled state br0: port 1(eth0) entering forwarding state SSDK Init OK! operate done. udhcp server (v0.9.8) started The attached devices demo is Running ... The telnetenable is running ... Deleting static route ... Done! Adding static route ... Done! usbcore: deregistering interface driver usbserial_generic USB Serial deregistering driver generic usbcore: deregistering interface driver usbserial rmmod: cdc_ncm: No such file or directory killall: failover: no process killed rmmod: usbserial: No such file or directory rmmod: usbserial: No such file or directory dni-qos attached on eth1. br0: port 1(eth0) entering disabled state dni-qos attached on br0. br0: port 1(eth0) entering forwarding state udhcp client (v0.9.8) started time zone index is : 21 Run NTP Client with setting: pri:time-b.netgear.com sec:time-c.netgear.com killall: miniupnpd: no process killed no 6RD parameters available, so unset 6rd related config killall: pppd: no process killed Deleting static route ... Done! Deleting static route ... Done! Adding static route ... Done! Jan 1 00:00:28 miniupnpd[1073]: listening on 192.168.1.1:5555 start rip process start initial data Sending discover... No user name for DDNS! syslogd can't open the temp log file: /tmp/log/log-message or /var/log/messages Starting Firewall... Done! The region number is: 0x0001 REGION: NA Generating RSA private key, 1024 bit long modulus ufsd:: trace mask set to 0000000f ufsd: driver (lke_9.0.0 lke_9.0.0_r233352_b3, LBD=ON, acl, ioctl, bdi, sd(0), w0 NTFS support included Big endian platform optimized: speed Build_for__NETGEAR_WNDR4500V3_k2.6.31_2014-06-18_lke_9.0.0_r233352_b3 kcg 333 :GPL NetUSB up! kc 90 : run_telnetDBGDServer start kc 227 : init_DebugD end INFO17ED: NetUSB 1.02.67, 0002061F : May 8 2015 15:43:52 INFO17EF: 7423: WNDR4500v3 :WNDR4500v3 INFO17F0: AUTH ISOC INFO17F1: MOVE_HEAD emb_lp filterAudio INFO0715: 0 : tunnelID emusblp 0 INFO0715: 1 : tunnelID emusblp 1 INFO0715: 2 : tunnelID emusblp 2 INFO0715: 3 : tunnelID emusblp 3 INFO0715: 4 : tunnelID emusblp 4 INFO0715: 5 : tunnelID emusblp 5 INFO0715: 6 : tunnelID emusblp 6 INFO0715: 7 : tunnelID emusblp 7 INFO0715: 8 : tunnelID emusblp 8 INFO0715: 9 : tunnelID emusblp 9 usbcore: registered new interface driver KC NetUSB General Driver INFO0ADC: --- checkSBusTimeoutThread start --- INFO0145: init proc : PAGE_SIZE 4096 INFO16E1: infomap 8730b410 INFO16E4: sleep to wait br0 to wake up INFO15B4: tcpConnector() started... : br0 Changing password for admin New password:Sending discover... Retype password:Generating selfsigned certificate with subject 'C=DE;ST=Saxony;0 AUTO FW CHECK: power cycle Password for admin changed by root killall: smbd: no process killed killall: smbd: no process killed killall: nmbd: no process killed USB Storage daemon is Running ... /etc/rc.common: /etc/rc.common: 117: detplc: not found FW checking ... week_day == 3 Changing password for admin New password:POT is Running... POT is Finished!!! The POT-(Get/Set) Demo is Running ... ADDRCONF(NETDEV_UP): sit0: link is not ready ADDRCONF(NETDEV_UP): phy0: link is not ready ADDRCONF(NETDEV_UP): pas0: link is not ready Retype password:usb 1-1: new high speed USB device using ath-ehci and address 3 usb 1-1: New USB device found, idVendor=1f75, idProduct=0916 usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-1: Product: IS916 usb 1-1: Manufacturer: Patriot Memory usb 1-1: SerialNumber: 09161000000411491100000472 usb 1-1: configuration #1 chosen from 1 choice [USB] usb led 0 on(0) INFO008C: Add device intf 86412300, dev 87b7f800 INFO0C02: filter pure storage dev scsi1 : SCSI emulation for USB Mass Storage devices Password for admin changed by root [USB-AFP]: Total 0 partitions are FOUND! killall: avahi-daemon: no process killed [USB-AFP]: Loading USB share information ......diskname: (null) disk_mouted=0, host_id=0 cat: /var/run/afpd.pid: No such file or directory Args: 1 Sending discover... ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Righd ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved ath_tx99: Version 2.0 Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reservd ath_ahb: 10.2-00085-8 (Atheros/multi-bss) __ath_attach: Set global_scn[0] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value w* ACBKMinfree = 48 ACBEMinfree = 32 ACVIMinfree = 16 ACVOMinfree = 0 CABMinfree = 48 UAPSDMinfree = 0 ATH_TXBUF=540 Enterprise mode: 0x03bda000 Restoring Cal data from Flash Green-AP : Green-AP : Attached ath_get_caps[6148] rx chainmask mismatch actual 3 sc_chainmak 0 ath_get_caps[6123] tx chainmask mismatch actual 3 sc_chainmak 0 ath_attach_dfs[12558] dfsdomain 1 ath_tx_paprd_init sc 870d8000 PAPRD disabled in HAL SC Callback Registration for wifi0 wifi0: Atheros 956X: mem=0xb8100000, irq=2 ath_pci: 10.2-00085-8 (Atheros/multi-bss) __ath_attach: Set global_scn[1] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value w* ACBKMinfree = 48 ACBEMinfree = 32 ACVIMinfree = 16 ACVOMinfree = 0 CABMinfree = 48 UAPSDMinfree = 0 ATH_TXBUF=540 Restoring Cal data from Flash Green-AP : Green-AP : Attached ath_get_caps[6148] rx chainmask mismatch actual 7 sc_chainmak 0 ath_get_caps[6123] tx chainmask mismatch actual 7 sc_chainmak 0 ath_attach_dfs[12558] dfsdomain 1 ath_tx_paprd_init sc 87058000 PAPRD disabled in HAL SC Callback Registration for wifi1 wifi1: Atheros ???: mem=0x12000000, irq=76 hw_base=0xb2000000 scsi 1:0:0:0: Direct-Access Patriot Memory 1.00 PQ: 0 ANSI: 6 sd 1:0:0:0: [sda] 8011776 512-byte logical blocks: (4.10 GB/3.82 GiB) sd 1:0:0:0: [sda] Write Protect is off sd 1:0:0:0: [sda] Assuming drive cache: write through sd 1:0:0:0: [sda] Assuming drive cache: write through sda: sda1 sd 1:0:0:0: [sda] Assuming drive cache: write through sd 1:0:0:0: [sda] Attached SCSI removable disk ath_attach_dfs[12558] dfsdomain 1 ath_attach_dfs[12558] dfsdomain 1 Creating sta for ARRIS-5249-5G on wlan_vap_create : enter. devhandle=0x85fa02c0, opmode=IEEE80211_M_STA, flags=0x3 wlan_vap_create : exit. devhandle=0x85fa02c0, opmode=IEEE80211_M_STA, flags=0x3. VAP device ath0 created Added ath0 mode managed Invalid command : bgscan Interface doesn't accept private ioctl... HALDbg (8BE0): Operation not permitted DES SSID SET=ARRIS-5249-5G ieee80211_ioctl_siwmode: imr.ifm_active=65664, new mode=2, valid=1 /etc/ath/makeVAP: /etc/ath/makeVAP: 492: cannot create /proc/sys/dev/ath/htdupit Invalid command : setVowExt Invalid command : setKeySrchAlways Invalid command : set_vsp_enable Invalid command : setPhyRestartWar Invalid command : setVowExtStats sc nodebug 0 Created ath0 mode sta for ARRIS-5249-5G lo no wireless extensions. sit0 no wireless extensions. phy0 no wireless extensions. br0 no wireless extensions. eth0 no wireless extensions. eth1 no wireless extensions. pas0 no wireless extensions. device ath0 entered promiscuous mode wifi0 no wireless extensions. wifi1 no wireless extensions. arping: bind: Cannot assign requested address >>>>> WPS MODE, main startmode: cb sub startmode: cb The extender led demo is Running ... Successfully initialized wpa_supplicant ieee80211_ioctl_getparam : parameter 0x284 not supported br0: port 3(ath0) entering forwarding state traffic_meter start : . killall: igmpproxy: no process killed bridge mode is on!! /etc/rc.common: /etc/rc.common: 117: get: not found Received SIGTERM Entering released state killall: minidlna: no process killed killall: zcip: no process killed br0: port 3(ath0) entering disabled state driver_atheros_e DES SSID SET=ARRIS-5249-5G vent_wireless: s[ieee80211_ioctl_setmlme] set desired bssid a4:2b:8c:86:32:21 can result eventvap-0: ieee80211_setup_node forcing sta to associate in 1 mode - SIOCGIWSCAN Getting extcaps from Scan Entry ath0: Trying to wlan_mlme_join_infra.. SETTING CHANNEL NUMBER 153 CURR CHANNEl 0 associate with a4:2b:8c:86:32:21 (SSID='ARRIS-5249-5G' freq=5765 MHz) killall: bpalogin: no process killed vap-0: ieee80211_setup_node forcing sta to associate in 1 mode Getting extcaps from Scan Entry wlan_mlme_join_infra.. SETTING CHANNEL NUMBER 153 CURR CHANNEl is 153 flags 0x10 br0: port 3(ath0) entering forwarding state ath0: Associated with a4:2b:8c:86:32:21 ath0: WPA: Key negotiation completed with a4:2b:8c:86:32:21 [PTK=CCMP GTK=CCMP] ath0: CTRL-EVENT-CONNECTED - Connection to a4:2b:8c:86:32:21 completed (auth) [] NET: Unregistered protocol family 24 ath0: received packet with own address as source address rmmod: ppp_generic: Resource temporarily unavailable rmmod: slhc: Resource temporarily unavailable Deleting static route ... Done! Adding static route ... Done! /etc/rc.common: /etc/rc.common: 117: /etc/init.d/leafp2p.sh: not found rm: cannot remove '/etc/ppp/pppoe2-domain.conf': No such file or directory rm: cannot remove '/etc/ppp/enable_ppp1': No such file or directory Terminated Stopping Firewall... Done! Deleting static route ... Done! br0: port 3(ath0) entering disabled state br0: port 1(eth0) entering disabled state br0: port 3(ath0) entering forwarding state br0: port 1(eth0) entering forwarding state ath0: received packet with own address as source address udhcp client (v0.9.8) started Sending discover... ps: invalid option -- e BusyBox v1.4.2 (2015-07-08 11:22:00 CST) multi-call binary Usage: ps Report process status Options: w Wide output pktlogconf: option requires an argument -- d Packet log configuration usage: pktlogconf [-a adapter] [-e[event-list]] [-d adapter] [-s log-size] [-t ] [-b -p -i] -h show this usage -a configures packet logging for specific 'adapter'; configures system-wide logging if this option is not specified -d disable packet logging -e enable logging events listed in the 'event-list' event-list is an optional comma separated list of one or more of the following: rx tx rcf rcu ani (eg., pktlogconf -erx,rcu,tx) -s change the size of log-buffer to "log-size" bytes -t enable logging of TCP headers -k enable triggered stop by a threshold number of TCP SACK packets -l change the number of packets to log after triggered stop -b enable triggered stop by a throuput threshold -p enable triggered stop by a PER threshold -i change the time period of counting throughput/PER Run Action ! check minidlna ... killall: minidlna: no process killed lo no wireless extensions. sit0 no wireless extensions. phy0 no wireless extensions. br0 no wireless extensions. eth0 no wireless extensions. eth1 no wireless extensions. pas0 no wireless extensions. wifi0 no wireless extensions. wifi1 no wireless extensions. ath0: received packet with own address as source address killing 4742 /etc/ath/killVAP: kill: 295: (4742) - No such process killing 2285 /etc/ath/killVAP: kill: 295: (4764) - No such process [*** USB Storage ***] Mounting USB Disk Partition sda1 ... EXT4-fs (sda1): barriers enabled kjournald2 starting: pid 5173, dev sda1:8, commit interval 5 seconds EXT4-fs (sda1): internal journal on sda1:8 EXT4-fs (sda1): delayed allocation enabled EXT4-fs: file extents enabled EXT4-fs: mballoc enabled EXT4-fs (sda1): recovery complete EXT4-fs (sda1): mounted filesystem with ordered data mode mount /mnt/sda1 success [*** USB Storage ***] Mounted the Disk sda <--> X-DISK successfully!!! usb0[1], usb1[0] ! [USB] usb led 0 KEEP ON ! Sending select for 192.168.0.72... disk_mouted=1, host_id=2 Lease of 192.168.0.72 obtained, lease time 3600 configure ip address got from DHCP Server ... deleting routers adding router 192.168.0.1 adding dns 192.168.0.1 check minidlna ... killall: minidlna: no process killed killall: smbd: no process killed device ath0 left promiscuous mode br0: port 3(ath0) entering disabled state killing ath0 _ieee80211_scan_unregister_event_handler: Failed to unregister evhandler=85c9630 _ieee80211_scan_unregister_event_handler: Failed to unregister evhandler=85c9630 _ieee80211_scan_unregister_event_handler: Failed to unregister evhandler=85c9610 vap-0: mlme_sta_swbmiss_timer_detach:id 0 name (SCANNER) is still allocated arping: bind: Cannot assign requested address Dev: sda1 vol_type: ext4 ret: 1 This HDD format can support the feature of Time Machine... ... [USB-AFP]: Found partition sda1, mounted Yes!!! [USB-AFP]: Total 1 partitions are FOUND! [USB-AFP] Exist avahi daemon num 1 ! [USB-AFP]: Loading USB share information ......diskname: sda [USB-AFP]: AFPInfo shared_stuff Folder:/ Reader:guest Writer: guest In First Step: valume: Args: 1 Green-AP : Green-AP : Detached Green-AP : Green-AP : Detached ath_ahb: driver unloaded Removing athdebug proc file ath_dev: driver unloaded ath_tx99: driver unloaded ath_dfs: driver unloaded ath_rate_atheros: driver unloaded ath_hal: driver unloaded Sorry, rule does not exist. Sorry, rule does not exist. Sorry, rule does not exist. Sorry, rule does not exist. Sorry, rule does not exist. Starting Firewall... Done! backupnstuff afplist: 1check minidlna ... Args: 1 ath_hal: 0.9.17.1 (AR5416, AR9380, REGOPS_FUNC, WRITE_EEPROM, TX_DATA_SWAP, RX_) ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Righd ath_dfs: Version 2.0.0 Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reserved ath_tx99: Version 2.0 Copyright (c) 2010 Atheros Communications, Inc, All Rights Reserved ath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reservd ath_ahb: 10.2-00085-8 (Atheros/multi-bss) __ath_attach: Set global_scn[0] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value w* ACBKMinfree = 48 ACBEMinfree = 32 ACVIMinfree = 16 ACVOMinfree = 0 CABMinfree = 48 UAPSDMinfree = 0 ATH_TXBUF=540 Enterprise mode: 0x03bda000 Restoring Cal data from Flash Green-AP : Green-AP : Attached ath_get_caps[6148] rx chainmask mismatch actual 3 sc_chainmak 0 ath_get_caps[6123] tx chainmask mismatch actual 3 sc_chainmak 0 ath_attach_dfs[12558] dfsdomain 1 ath_tx_paprd_init sc 870d8000 PAPRD disabled in HAL SC Callback Registration for wifi0 wifi0: Atheros 956X: mem=0xb8100000, irq=2 ath_pci: 10.2-00085-8 (Atheros/multi-bss) __ath_attach: Set global_scn[1] *** All the minfree values should be <= ATH_TXBUF-32, otherwise default value w* ACBKMinfree = 48 ACBEMinfree = 32 ACVIMinfree = 16 ACVOMinfree = 0 CABMinfree = 48 UAPSDMinfree = 0 ATH_TXBUF=540 Restoring Cal data from Flash Green-AP : Green-AP : Attached ath_get_caps[6148] rx chainmask mismatch actual 7 sc_chainmak 0 ath_get_caps[6123] tx chainmask mismatch actual 7 sc_chainmak 0 ath_attach_dfs[12558] dfsdomain 1 ath_tx_paprd_init sc 87058000 PAPRD disabled in HAL SC Callback Registration for wifi1 wifi1: Atheros ???: mem=0x12000000, irq=76 hw_base=0xb2000000 ath_attach_dfs[12558] dfsdomain 1 ath_attach_dfs[12558] dfsdomain 1 Creating sta for ARRIS-5249-5G on wlan_vap_create : enter. devhandle=0x864b02c0, opmode=IEEE80211_M_STA, flags=0x3 wlan_vap_create : exit. devhandle=0x864b02c0, opmode=IEEE80211_M_STA, flags=0x3. VAP device ath0 created Added ath0 mode managed Invalid command : bgscan Interface doesn't accept private ioctl... HALDbg (8BE0): Operation not permitted DES SSID SET=ARRIS-5249-5G ieee80211_ioctl_siwmode: imr.ifm_active=65664, new mode=2, valid=1 /etc/ath/makeVAP: /etc/ath/makeVAP: 492: cannot create /proc/sys/dev/ath/htdupit Invalid command : setVowExt Invalid command : setKeySrchAlways Invalid command : set_vsp_enable Invalid command : setPhyRestartWar Invalid command : setVowExtStats sc nodebug 0 Created ath0 mode sta for ARRIS-5249-5G lo no wireless extensions. sit0 no wireless extensions. phy0 no wireless extensions. br0 no wireless extensions. eth0 no wireless extensions. eth1 no wireless extensions. pas0 no wireless extensions. wifi0 no wireless extensions. wifi1 no wireless extensions. device ath0 entered promiscuous mode arping: bind: Cannot assign requested address >>>>> WPS MODE, main startmode: cb sub startmode: cb The extender led demo is Running ... Successfully initialized wpa_supplicant ieee80211_ioctl_getparam : parameter 0x284 not supported br0: port 3(ath0) entering forwarding state The attached devices demo is Running ... Jan 1 00:01:16 lld2d[6869]: osl_write_pidfile: /var/run/lld2d-br0.pid containsg br0: port 3(ath0) entering disabled state driver_atheros_e DES SSID SET=ARRIS-5249-5G vent_wireless: s[ieee80211_ioctl_setmlme] set desired bssid a4:2b:8c:86:32:21 can result eventvap-0: ieee80211_setup_node forcing sta to associate in 1 mode - SIOCGIWSCAN Getting extcaps from Scan Entry ath0: Trying to wlan_mlme_join_infra.. SETTING CHANNEL NUMBER 153 CURR CHANNEl 0 associate with a4:2b:8c:86:32:21 (SSID='ARRIS-5249-5G' freq=5765 MHz) vap-0: ieee80211_setup_node forcing sta to associate in 1 mode Getting extcaps from Scan Entry wlan_mlme_join_infra.. SETTING CHANNEL NUMBER 153 CURR CHANNEl is 153 flags 0x10 br0: port 3(ath0) entering forwarding state ath0: Associated with a4:2b:8c:86:32:21 ath0: WPA: Key negotiation completed with a4:2b:8c:86:32:21 [PTK=CCMP GTK=CCMP] ath0: CTRL-EVENT-CONNECTED - Connection to a4:2b:8c:86:32:21 completed (auth) [] Performing a DHCP renew Sending renew... Jan 1 00:01:18 miniupnpd[6920]: listening on 192.168.1.1:5555 Jan 1 00:01:18 miniupnpd[6920]: setsockopt(udp, IP_ADD_MEMBERSHIP): No such dee Jan 1 00:01:18 miniupnpd[6920]: Failed to open socket for SSDP. EXITING check minidlna ... killall: minidlna: no process killed Sending renew... ath0: received packet with own address as source address Sending renew... time zone index is : 21 Run NTP Client with setting: pri:time-b.netgear.com sec:time-c.netgear.com Jan 1 00:01:23 crond[7145]: crond 2.3.2 dillon, started, log level 8 mtdoops: Attached to MTD device 13 name mtdoops Boot up procedure is Finished!!! Please press Enter to activate this console. Performing a DHCP renew Sending discover... Sending select for 192.168.0.72... BusyBox v1.4.2 (2015-07-08 11:22:00 CST) Built-in shell (ash) Enter 'help' for a list of built-in commands. _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M KAMIKAZE (bleeding edge, r18571) ------------------ * 10 oz Vodka Shake well with ice and strain * 10 oz Triple sec mixture into 10 shot glasses. * 10 oz lime juice Salute! --------------------------------------------------- root@WNDR4300v2:/# Lease of 192.168.0.72 obtained, lease time 3600 configure ip address got from DHCP Server ... deleting routers adding router 192.168.0.1 adding dns 192.168.0.1 Starting Firewall... Done! The abbreviation of English is Eng! Passed the checksum verification!


OpenWrt bootlog

COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


Notes

Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
inbox/toh/netgear/netgear_wndr4300_2.txt · Last modified: 2019/10/14 15:55 by tmomas