Netgear RAX40

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

A 802.11ax Wi-Fi 6 device with Intel (Lantiq) PXB4395 chip.

Netgear RAX40

CPU Ram Flash Network WLAN 2.4Ghz WLAN 5Ghz USB Serial JTag
Intel AnyWAN SoC GRX350 @ 800 MHz 512 MiB 256 MiB 5x Gigabit b/g/n/ax a/n/ac/ax 1x 3.0 Yes No
Architecture Mips
Vendor Intel
Bootloader U-Boot 2010.06-LANTIQ-v-2.3.149-R11
System-On-Chip Intel GRX500 rev 1.2
CPU/Speed 800 MHz
Flash-Chip MXIC MX30LF2G18AC
Flash size 256 MiB
RAM-Chip Samsung K4B4G1646E-BYMA
RAM 512 MiB
Wireless Intel (Lantiq) WAV654
Ethernet 10/100/1000 Mbit/s w/ vlan support
Switch Intel (Lantiq) PXB4395
USB 1x 3.0
Serial Yes
JTAG No

Flash layout in Original Netgear OEM FW:

[    2.790000] Creating 8 MTD partitions on "17c00000.nand-parts":
[    2.790000] 0x000000000000-0x000000100000 : "uboot"
[    2.800000] 0x000000100000-0x000000140000 : "ubootconfigA"
[    2.810000] 0x000000140000-0x000000180000 : "ubootconfigB"
[    2.810000] 0x000000180000-0x0000001c0000 : "gphyfirmware"
[    2.820000] 0x0000001c0000-0x0000002c0000 : "calibration"
[    2.820000] 0x0000002c0000-0x00000f8c0000 : "system_sw"
[    2.830000] 0x00000f8c0000-0x00000ff80000 : "vendor"
[    2.830000] 0x00000ff80000-0x000010000000 : "res"

Insert photo of front of the casing

Insert photo of back of the casing

Insert photo of backside label

Insert photo of PCB

FIXME Describe what needs to be done to open the device, e.g. remove rubber feet, adhesive labels, screws, ...

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

FIXME Replace EXAMPLE by real values.

Serial connection parameters for Netgear RAX40 R1.05 115200, 8N1

Not supported.

U-Boot 2010.06-LANTIQ-v-2.3.149-R11 (Jan 25 2019 - 19:28:44) interAptiv cps cpu/ddr run in 800/666 Mhz DRAM: 224 MiB NAND: ONFI flash detected ONFI param page 0 valid NAND device: Manufacturer ID: 0xc2, Chip ID: 0xda (MXIC MX30LF2G18AC) 256 MiB Bad block table found at page 131008, version 0x01 Bad block table found at page 130944, version 0x01 nand_read_bbt: Bad block at 0x000006060000 In: serial Out: serial Err: serial Net: multi type Internal phy firmware version: 0x8548 GRX500 Switch Type "run flash_nfs" to mount root filesystem over NFS Run NMRP & wait 3 seconds for linkup ..... Hit any key to stop autoboot: 0 Creating 1 MTD partitions on "nand0": 0x0000002c0000-0x00000f8c0000 : "mtd=5" UBI: attaching mtd1 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd1 to ubi0 UBI: MTD device name: "mtd=5" UBI: MTD device size: 246 MiB UBI: number of good PEBs: 1967 UBI: number of bad PEBs: 1 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 7 UBI: available PEBs: 975 UBI: total number of reserved PEBs: 992 UBI: number of PEBs reserved for bad PEB handling: 19 UBI: max/mean erase counter: 2148/1134 Volume bootcoreA found at volume id 6 read 0 bytes from volume 6 to a0400000(buf address) Read [2031616] bytes Volume kernelA found at volume id 0 read 0 bytes from volume 0 to 80800000(buf address) Read [2920448] bytes ## Booting kernel from Legacy Image at 80800000 ... Image Name: MIPS LTQCPE Linux-3.10.108 Created: 2020-05-22 3:48:37 UTC Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2883520 Bytes = 2.7 MiB Load Address: a0020000 Entry Point: a002df00 Verifying Checksum ... OK Uncompressing Kernel Image ... OK


Starting kernel ... [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Linux version 3.10.108 (bruce@buildSrv203) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 15.05_ltq) ) #5 SMP Fri May 22 11:48:08 CST 2020 [ 0.000000] TLBINV/F supported, config4=0xc0000000 [ 0.000000] TLBINV/F supported, config4=0xc0000000 [ 0.000000] SoC: GRX500 rev 1.2 [ 0.000000] GCMP present [ 0.000000] L2-only SYNC available [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001a120 (MIPS interAptiv) [ 0.000000] Enhanced Virtual Addressing (EVA 1GB) activated [ 0.000000] IO: BASE = 0xa0000000, SHIFT = 0x10000000, SIZE = 0x10000000 [ 0.000000] GCMP base addr = 0xb2300000, CLB: ResetExcBase = 0xbfc00000, ResetExcExtBase = 0x4ff00001 [ 0.000000] BEV Overlay segment = 0xb0000000, size = 0x10000000 [ 0.000000] segctr0 2d0a0a segctr1 40d020a segctr2 38004d [ 0.000000] MIPS: machine is EASY350 ANYWAN (GRX350) Router model [ 0.000000] CMP IOCU detected [ 0.000000] Hardware DMA cache coherency disabled [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 1e000000 @ 20000000 (usable) [ 0.000000] User-defined physical RAM map: [ 0.000000] memory: 1e000000 @ 20000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] reserving 18874368 bytes @ 68009b80 for CBM [ 0.000000] reserving 8388608 bytes @ 69209b80 for CBM [ 0.000000] Zone ranges: [ 0.000000] DMA [mem 0x20000000-0x27ffffff] [ 0.000000] Normal [mem 0x28000000-0x3dffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x20000000-0x3dffffff] [ 0.000000] Detected 3 available secondary CPU(s) [ 0.000000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] PERCPU: Embedded 7 pages/cpu @69dce000 s8064 r8192 d12416 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 121920 [ 0.000000] Kernel command line: ubi.mtd=system_sw rootfsname=rootfsA ro rootfstype=squashfs do_overlay console=ttyLTQ0,115200 ethaddr=78:D2:94:E7:FC:F0 panic=1 mtdparts=17c00000.nand-parts:1m(uboot),256k(ubootconfigA),256k(ubootconfigB),256k(gphyfirmware),1m(calibration),246m(system_sw),6912k(vendor),-(res) init=/etc/preinit active_bank=A update_chk=0 maxcpus=4 pci=pcie_bus_perf ethwan= ubootver=U-Boot-2010.06-LANTIQ-v-2.3.149-R11 mem=480M@512M [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] allocated 983040 bytes of page_cgroup [ 0.000000] please try 'cgroup_disable=memory' option if you don't want memory cgroups [ 0.000000] Memory: 449424k/491520k available (6288k kernel code, 42096k reserved, 1861k data, 296k init, 0k highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:527 [ 0.000000] GIC: present [ 0.000000] EIC: off [ 0.000000] GIC map size 263 [ 0.000000] gic: revision 3.0 [ 0.000000] CPU0: c0 status register 1100fc00 [ 0.000000] of_gic_init init done [ 0.000000] CPU Clock: 800000000Hz mips_hpt_frequency 400000000Hz [ 0.000000] CBM Clock: 600000000Hz DDR Clock: 666666666Hz NGI Clock: 300000000Hz [ 0.000000] clock event init done ! [ 0.000000] gptu_setup_clocksource: done ! [ 0.000000] Calibrating delay loop... 513.63 BogoMIPS (lpj=2568192) [ 0.070000] pid_max: default: 32768 minimum: 301 [ 0.070000] Mount-cache hash table entries: 512 [ 0.080000] Initializing cgroup subsys memory [ 0.080000] size of core = 336, MAXCORE = 2 , MAXCPU = 4, MAXTCS = 6 MAX_VPE = 2 [ 0.090000] [update_DB_from_DT]:[363], cpuid = 0 name = LINUX [ 0.090000] [update_DB_from_DT]:[363], cpuid = 1 name = VOICEFW [ 0.100000] [update_DB_from_DT]:[363], cpuid = 2 name = LINUX [ 0.100000] [update_DB_from_DT]:[363], cpuid = 3 name = MPEFW [ 0.110000] [vmb_check_IBL_fw_msg]:[331] vpet[j].bl_status = 2 , cpu = 1 [ 0.110000] [vmb_check_IBL_fw_msg]:[331] vpet[j].bl_status = 2 , cpu = 2 [ 0.120000] [vmb_check_IBL_fw_msg]:[331] vpet[j].bl_status = 2 , cpu = 3 [ 0.120000] [ 0.120000] Initial ITC_Address_Map0 00000000 [ 0.130000] def ITC_Address_Map1 01200000 new ITC_Address_Map1 0120fc00 def ITC_Address_Map0 00000000 new ITC_Address_Map0 1c300001 ITC Init done on Core 0 on CPU 0 !!! [ 0.140000] [smp_init]:[553] CPU1 shouldn't run LINUX as per DT (model) config [ 0.150000] [vmb_cpu_alloc]:[624] CPU vpet.cpu_status = 11 [ 0.150000] [vmb_cpu_start]:[849] vmb_fw_msg_t = a0000168 cpu = 2 vmb_msg_size = b0 sizeof(VMB_fw_msg_t) = 168 sizeof(FW_vmb_msg_t) = 8 !!!! [gic_trigger]:[555] VMB_CPU_IPI2 - 21 CPU = 2 Outside WAIT got IPI interrupt to launch from cpu 02 MSG_ID = 01[ 0.160000] [vmb_cpu_start]:[892] WAITING FOR RESPONSE vpet->v_wq.wakeup_vpe = 0 !!!! [ 0.160000] TLBINV/F supported, config4=0xc0000000 [ 0.160000] TLBINV/F supported, config4=0xc0000000 [ 0.160000] Primary instruction cache 32kB, 4-way, VIPT, linesize 32 bytes. [ 0.160000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.160000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.160000] IO: BASE = 0xa0000000, SHIFT = 0x10000000, SIZE = 0x10000000 [ 0.160000] GCMP base addr = 0xb2300000, CLB: ResetExcBase = 0xbfc00000, ResetExcExtBase = 0x4ff00001 [ 0.160000] BEV Overlay segment = 0xb0000000, size = 0x10000000 [ 0.160000] [ 0.160000] Initial ITC_Address_Map0 00000000 [ 0.160000] [ 0.160000] def ITC_Address_Map1 01200000 [ 0.160000] new ITC_Address_Map1 0120fc00 [ 0.160000] def ITC_Address_Map0 00000000 [ 0.160000] new ITC_Address_Map0 1c300001 [ 0.160000] ITC Init done on Core 1 on CPU 2 !!! [ 0.160000] CPU2 revision is: 0001a120 (MIPS interAptiv) [ 0.220000] [vmb_cpu_active]:[268] action = 10 , cpu = 2 [ 0.220000] [vmb_cpu_start]:[908] OUTSIDE WAIT wakeup_vpe = 1 vpet->fw_vmb.status = 1 ACK = 1 cpu = 2 ret1 = 9995 vpet = 608678c4, smp_processor_id() = 0 , vpet->fw_vmb =608678f0 !!!! [ 0.220000] [vmb_cpu_start]:[915] ret = 1 [ 0.230000] Synchronize counters for CPU 2: done. [ 0.230000] GPTC clock event init on cpu: 2 [ 0.230000] clock event init done ! [ 0.240000] [smp_init]:[553] CPU3 shouldn't run LINUX as per DT (model) config [ 0.240000] Brought up 2 CPUs [ 0.260000] pinctrl core: initialized pinctrl subsystem [ 0.260000] NET: Registered protocol family 16 [ 0.270000] [gpio_xrx500] { xrx500_gpio_init : 412 }XRX500 GPIO Driver, (C) 2014 Lantiq Deutschland Gmbh [ 0.280000] Resetting the switch and phy. [ 0.280000] dma-grx500 1e300000.dma: DMA3 base address be300000 chained_irq 77 irq_base 447 [ 0.290000] dma-grx500 1e300000.dma: Init done - hw rev: A, ports: 1, channels: 64 [ 0.300000] dma-grx500 1c100000.dma: DMA2TX base address bc100000 chained_irq 75 irq_base 399 [ 0.310000] dma-grx500 1c100000.dma: Init done - hw rev: A, ports: 1, channels: 16 [ 0.310000] dma-grx500 1c200000.dma: DMA2RX base address bc200000 chained_irq 76 irq_base 415 [ 0.320000] dma-grx500 1c200000.dma: Init done - hw rev: A, ports: 1, channels: 32 [ 0.330000] dma-grx500 1a100000.dma: DMA1TX base address ba100000 chained_irq 73 irq_base 351 [ 0.340000] dma-grx500 1a100000.dma: Init done - hw rev: A, ports: 1, channels: 16 [ 0.340000] dma-grx500 1a200000.dma: DMA1RX base address ba200000 chained_irq 74 irq_base 367 [ 0.350000] dma-grx500 1a200000.dma: Init done - hw rev: A, ports: 1, channels: 12 [ 0.360000] [gptu] { gptu_probe : 297 }dev id 16b00000.gptu [ 0.360000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.370000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.370000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.380000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.380000] gptu-xrx500 16b00000.gptu: gptu: 4 timers loaded [ 0.390000] gptu driver init successfully [ 0.390000] [gptu] { gptu_probe : 297 }dev id 16300000.gptu [ 0.400000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.400000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.410000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.410000] [gptu] { clkdev_add_gptu : 239 }Memory Allocation suceeded [ 0.420000] gptu-xrx500 16300000.gptu: gptu: 4 timers loaded [ 0.420000] gptu driver init successfully [ 0.430000] dma0-grx500 16e00000.dma: base address b6e00000 chained_irq 72 irq_base 335 [ 0.430000] dma0-grx500 16e00000.dma: Init done - hw rev: A, ports: 4, channels: 16 [ 0.440000] [pinctrl_xrx500] { pinctrl_xrx500_probe : 1493 }disabling the BBSPI at top-mux [ 0.440000] [pinctrl_xrx500] { pinctrl_xrx500_probe : 1516 }SoC id is - 32,default XRX500 pinmuxing will used [ 0.450000] pinctrl-xrx500 pinctrl.4: Init done [ 0.450000] gpio-xrx500 16c00000.gpio: gpio: 49 is out of the gpio chip range:(0, 32) [ 0.460000] gpio-xrx500 16c00000.gpio: gpio: 50 is out of the gpio chip range:(0, 32) [ 0.460000] gpio-xrx500 16c00000.gpio: gpio: 51 is out of the gpio chip range:(0, 32) [ 0.470000] gpio-xrx500 16c00000.gpio: gpio: 52 is out of the gpio chip range:(0, 32) [ 0.470000] gpio-xrx500 16c00000.gpio: gpio: 53 is out of the gpio chip range:(0, 32) [ 0.480000] gpio-xrx500 16c00000.gpio: gpio: 54 is out of the gpio chip range:(0, 32) [ 0.480000] gpio-xrx500 16c00000.gpio: gpio: 55 is out of the gpio chip range:(0, 32) [ 0.490000] gpio-xrx500 16c00000.gpio: gpio: 56 is out of the gpio chip range:(0, 32) [ 0.490000] gpio-xrx500 16c00000.gpio: gpio: 57 is out of the gpio chip range:(0, 32) [ 0.500000] gpio-xrx500 16c00000.gpio: gpio: 59 is out of the gpio chip range:(0, 32) [ 0.500000] gpio-xrx500 16c00000.gpio: gpio: 60 is out of the gpio chip range:(0, 32) [ 0.510000] !!!!!!! WAVE400 system registeration on AHB [ 0.520000] MTLK_MEM_BAR1_START is 14000000 [ 0.520000] MTLK_MEM_BAR1_END is 147fffff [ 0.520000] MTLK_WIRELESS_IRQ_IN_INDEX is 26 [ 0.530000] [cbm] { cbm_xrx500_probe : 6073 }2 [ 0.530000] Initializing TMU with Base Address=be700000: ... [ 0.540000] TMU Initialization Done [ 0.540000] [cbm] { init_fsqm_buf_standard : 739 }init fsqm std successfully [ 0.550000] [cbm] { init_fsqm_buf_jumbo : 780 }init fsqm jbo successfully [ 0.550000] [cbm] { init_fsqm : 665 }fsqm init successfully [ 0.560000] [cbm] { init_cbm_basic : 853 }init basic CBM successfully [ 0.560000] [cbm] { cbm_hw_init : 2028 }CBM HW init [ 0.570000] [cbm] { setup_DMA_p2p : 5411 }setup_DMA_p2p executed [ 0.570000] [cbm] { configure_ports : 5739 }tmu_port 3 [ 0.580000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 0.580000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 0.590000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 0.590000] [cbm] { configure_ports : 5739 }tmu_port 2 [ 0.600000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 0.600000] [cbm] { configure_ports : 5859 }configure_ports 7 1 0 0 8 2 [ 0.610000] [cbm] { configure_ports : 5826 }configure_ports 7 1 16 1 8 2 [ 0.610000] [cbm] { configure_ports : 5859 }configure_ports 8 1 15 0 8 2 [ 0.620000] [cbm] { configure_ports : 5826 }configure_ports 8 1 31 1 8 2 [ 0.620000] [cbm] { init_cbm_ls : 1206 }Load spreader init successfully [ 0.630000] [cbm] { cbm_xrx500_probe : 6136 }CBM Clock: 600000000Hz [ 0.630000] [cbm] { cbm_xrx500_probe : 6138 }EQM delay Enabled [ 0.640000] [cbm] { cbm_xrx500_probe : 6207 }CBM: Init Done !! [ 0.640000] PCI host bridge /ssx3@18000000/pcie@900000 ranges: [ 0.650000] MEM 0x00000000b8000000..0x00000000baffffff [ 0.650000] IO 0x00000000bb800000..0x00000000bb8fffff [ 0.760000] PCIe LCPLL SSC Mode Enabled [ 0.990000] Lantiq PCIe Root Complex Port 0 Init Done [ 1.000000] PCI host bridge /ssx3@18000000/pcie@400000 ranges: [ 1.000000] MEM 0x00000000b4000000..0x00000000b6ffffff [ 1.010000] IO 0x00000000b7800000..0x00000000b78fffff [ 1.310000] Lantiq PCIe Root Complex Port 1 Init Done [ 1.320000] PCI host bridge /ssx3@18000000/pcie@E00000 ranges: [ 1.320000] MEM 0x00000000bc000000..0x00000000beffffff [ 1.330000] IO 0x00000000bf800000..0x00000000bf8fffff [ 1.930000] pcie_wait_phy_link_up port 2 timeout [ 1.940000] pcie_rc_initialize port 2 link up failed!!!!! [ 1.940000] ltq-pcie: probe of 18e00000.pcie failed with error -5 [ 1.970000] bio: create slab <bio-0> at 0 [ 1.970000] vgaarb: loaded [ 1.970000] SCSI subsystem initialized [ 1.980000] Register xway nand done! [ 1.980000] usbcore: registered new interface driver usbfs [ 1.990000] usbcore: registered new interface driver hub [ 1.990000] usbcore: registered new device driver usb [ 2.000000] try to register spd_mon driver [ 2.000000] spdmon 16080110.speedm: base address: 0xb6080110 [ 2.010000] spdmon 16080110.speedm: PHY base address: 0x16080110 [ 2.010000] device number :253 [ 2.020000] spdmon 16080110.speedm: spd_mon driver : init done !! [ 2.020000] spd_mon driver registered [ 2.030000] PCI host bridge to bus 0000:00 [ 2.030000] pci_bus 0000:00: root bus resource [mem 0xb8000000-0xbaffffff] [ 2.040000] pci_bus 0000:00: root bus resource [io 0xbb800000-0xbb8fffff] [ 2.040000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 2.050000] ltq-pcie 18900000.pcie: pcie_rc_class_fixup port 0: fixed pci host bridge to pci-pci bridge [ 2.060000] pci 0000:00:00.0: BAR 8: assigned [mem 0xb8000000-0xb9ffffff] [ 2.060000] pci 0000:01:00.0: BAR 0: assigned [mem 0xb8000000-0xb9ffffff] [ 2.070000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 2.070000] pci 0000:00:00.0: bridge window [mem 0xb8000000-0xb9ffffff] [ 2.080000] PCI: Enabling device 0000:00:00.0 (0000 -> 0002) [ 2.080000] pci 0000:00:00.0: PCI-E Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256 [ 2.090000] pci 0000:01:00.0: PCI-E Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256 [ 2.090000] PCI host bridge to bus 0000:02 [ 2.100000] pci_bus 0000:02: root bus resource [mem 0xb4000000-0xb6ffffff] [ 2.100000] pci_bus 0000:02: root bus resource [io 0xb7800000-0xb78fffff] [ 2.110000] pci_bus 0000:02: No busn resource found for root bus, will use [bus 02-ff] [ 2.110000] ltq-pcie 18400000.pcie: pcie_rc_class_fixup port 1: fixed pci host bridge to pci-pci bridge [ 2.120000] pci 0000:02:00.0: bridge configuration invalid ([bus 03-01]), reconfiguring [ 2.120000] pci 0000:02:00.0: BAR 8: assigned [mem 0xb4000000-0xb5ffffff] [ 2.130000] pci 0000:03:00.0: BAR 0: assigned [mem 0xb4000000-0xb5ffffff] [ 2.130000] pci 0000:02:00.0: PCI bridge to [bus 03] [ 2.140000] pci 0000:02:00.0: bridge window [mem 0xb4000000-0xb5ffffff] [ 2.140000] PCI: Enabling device 0000:02:00.0 (0000 -> 0002) [ 2.150000] pci 0000:02:00.0: PCI-E Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256 [ 2.150000] pci 0000:03:00.0: PCI-E Max Payload Size set to 256/ 256 (was 128), Max Read Rq 256 [ 2.160000] NET: Registered protocol family 8 [ 2.160000] NET: Registered protocol family 20 [ 2.170000] Switching to clocksource gptc-timer [ 2.170000] NET: Registered protocol family 2 [ 2.180000] TCP established hash table entries: 4096 (order: 3, 32768 bytes) [ 2.180000] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) [ 2.190000] TCP: Hash tables configured (established 4096 bind 4096) [ 2.190000] TCP: reno registered [ 2.200000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 2.200000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 2.210000] NET: Registered protocol family 1 [ 2.210000] RPC: Registered named UNIX socket transport module. [ 2.220000] RPC: Registered udp transport module. [ 2.220000] RPC: Registered tcp transport module. [ 2.230000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 2.240000] ltq-pcie 18900000.pcie: pcie_fixup_bridge port 0 : fixup host controller 0000:00:00.0 (1bef:0030) [ 2.250000] ltq-pcie 18400000.pcie: pcie_fixup_bridge port 1 : fixup host controller 0000:02:00.0 (1bef:0030) [ 2.260000] audit: initializing netlink socket (disabled) [ 2.260000] type=2000 audit(2.260:1): initialized [ 2.270000] VFS: Disk quotas dquot_6.5.2 [ 2.270000] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) [ 2.280000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 2.290000] SGI XFS with ACLs, security attributes, large block/inode numbers, no debug enabled [ 2.300000] msgmni has been set to 877 [ 2.300000] io scheduler noop registered [ 2.310000] io scheduler deadline registered (default) [ 2.310000] io scheduler cfq registered [ 2.320000] [vmb_yr_get]:[1372] CPU = 0, yri[i].yr_status = 1, yield_bits = 1 n_yr = 1 yri[i].cpu_id = 0 [ 2.330000] [vmb_yr_get]:[1372] CPU = 2, yri[i].yr_status = 1, yield_bits = 1 n_yr = 1 yri[i].cpu_id = 2 [ 2.340000] UMT initialize called on processor: 0 ! [ 2.340000] <umt_init>pmask addr = b2320494 and bit = 4 [ 2.350000] [vmb_tc_alloc]:[948] CPU tct[i].tc_status = 1 [ 2.350000] <umt_init>allocated TC num 2 [ 2.350000] getmvpctrl = 2 [ 2.360000] getvpectrl for target TC = 2 [ 2.360000] gettcstatus = 8400 [ 2.360000] tc is halted = 1 [ 2.370000] gettcbind = 400000 [ 2.370000] stack top = 60887ff0 [ 2.370000] start address of TC = 602ffe70 [ 2.380000] current TC status = a400 [ 2.380000] tc is unhalted = 0 [ 2.390000] current mvp control = 1 [ 2.390000] Yield setup passed for gptc_irq = 172 [ 2.390000] setting the gptu rate to: 25000 [ 2.400000] [gptu] { setrate : 154 }cpu_clk 200000000 [ 2.400000] [gptu] { setrate : 158 }reload_counter_value 8000 [ 2.410000] umt_init Timer 3A is running for UMT ! [ 2.410000] UMT initialize success on processor: 0 ! [ 2.420000] HW MCPY driver: Version: 1.1.0, Init Done !! [ 2.420000] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled [ 2.430000] lantiq,asc 16600000.serial: pins are not configured from the driver [ 2.440000] 16600000.serial: ttyLTQ0 at MMIO 0x16600000 (irq = 111) is a lantiq,asc [ 2.450000] console [ttyLTQ0] enabled, bootconsole disabled [ 2.450000] console [ttyLTQ0] enabled, bootconsole disabled [ 2.470000] Lantiq MIPSInterAptiv MPS driver, version 1.0.0.0, (c) 2006-2013 Lantiq Deutschland GmbH [ 2.470000] MPS: major Id 250 [ 2.480000] Major Id is 249 [ 2.480000] ICC driver registered [ 2.480000] sysrst_init: Trying to register System Reset Driver ... [ 2.490000] sysrst_pre_init: Detect InterAptiv CPU ... [ 2.490000] sysrst_init: Lantiq CPE GRX500 System driver version 1.0.0 [ 2.500000] sysrst_init: GRX500 System Reset initialized successfully! [ 2.510000] brd: module loaded [ 2.510000] loop: module loaded [ 2.510000] Uniform Multi-Platform E-IDE driver [ 2.520000] ide-gd driver 1.18 [ 2.520000] ONFI param page 0 valid [ 2.530000] ONFI flash detected [ 2.530000] NAND device: Manufacturer ID: 0xc2, Chip ID: 0xda (Macronix MX30LF2G18AC), 256MiB, page size: 2048, OOB size: 64 [ 2.540000] Scanning device for bad blocks [ 2.630000] Bad eraseblock 771 at 0x000006060000 [ 2.780000] 8 cmdlinepart partitions found on MTD device 17c00000.nand-parts [ 2.790000] Creating 8 MTD partitions on "17c00000.nand-parts": [ 2.790000] 0x000000000000-0x000000100000 : "uboot" [ 2.800000] 0x000000100000-0x000000140000 : "ubootconfigA" [ 2.810000] 0x000000140000-0x000000180000 : "ubootconfigB" [ 2.810000] 0x000000180000-0x0000001c0000 : "gphyfirmware" [ 2.820000] 0x0000001c0000-0x0000002c0000 : "calibration" [ 2.820000] 0x0000002c0000-0x00000f8c0000 : "system_sw" [ 2.830000] 0x00000f8c0000-0x00000ff80000 : "vendor" [ 2.830000] 0x00000ff80000-0x000010000000 : "res" [ 2.840000] Gluebi: Found kernel commandline option 'rootfsname=rootfsA' [ 2.840000] spi-lantiq-ssc 16800000.spi: master is unqueued, this is deprecated [ 2.850000] Lantiq SoC SPI controller rev 9 (TXFS 32, RXFS 32, DMA 1) [ 2.860000] [ltq_ssc] { ifx_ssc_init : 3802 }[ifx_ssc_init] force ifx_ssc_cs_low to PORT 1 [ 2.860000] [ltq_ssc] { ifx_ssc_init : 3803 }[ifx_ssc_init] force ifx_ssc_cs_high to PORT 1 [ 2.870000] [ltq_ssc] { ifx_ssc_init : 3807 }ifx_ssc_init ifx_ssc_init_count 1 [ 2.880000] [ltq_ssc] { ifx_ssc_init : 3930 }port name ltq_ssc1 [ 2.890000] [ltq_ssc] { ifx_ssc_init : 4026 }Lantiq SoC SSC controller rev 9 (TXFS 32, RXFS 32, DMA 1) [ 2.900000] [ltq_ssc] { ifx_sscAllocConnection : 3511 }ifx_sscAllocConnection ssc driver must be loaded first! [ 2.910000] ifx_spi_flash_init: failed to register sflash [ 2.910000] IMQ driver loaded successfully. (numdevs = 3, numqueues = 1) [ 2.920000] Hooking IMQ after NAT on PREROUTING. [ 2.920000] Hooking IMQ after NAT on POSTROUTING. [ 2.930000] pcnet32: pcnet32.c:v1.35 21.Apr.2008 tsbogend@alpha.franken.de [ 2.940000] Lantiq VRX318 Version 3.0.0 [ 2.940000] LTQ ETH SWITCH API, Version 3.0.2. [ 2.940000] SWAPI: Registered char device [switch_api] with major no [81] [ 2.950000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1725 (pnum:7) [ 2.960000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1792 (gswdev->gipver:48) [ 2.970000] LTQ ETH SWITCH API, Version 3.0.2. [ 2.970000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1725 (pnum:2) [ 2.980000] drivers/net/ethernet/lantiq/switch-api/gsw_flow_core.c:get_gsw_hw_cap:1792 (gswdev->gipver:48) [ 3.000000] gphy_driver_init: fw_mode:11G-FW, no of phys:5, mode:0 [ 3.000000] [datapath_loopeth_dev] { dp_loop_eth_dev_init : 1686 }Loading loop_net_dev driver ...... [ 3.010000] [datapath_loopeth_dev] { dp_loop_eth_dev_init : 1692 }dp_loop_eth_dev_init Succeeded! [ 3.020000] [datapath_coc] { dp_coc_new_stat_req : 803 }COC is not initialized yet in DP [ 3.030000] dp init done [ 3.030000] lro_sram_membase_res0 from DT: a2013000 [ 3.040000] ltq_toe_membase: e2000000 and lro_sram_membase_res0: e2013000 [ 3.040000] TOE Init Done !! [ 3.050000] PPP generic driver version 2.4.2 [ 3.050000] PPP BSD Compression module registered [ 3.060000] PPP Deflate Compression module registered [ 3.060000] PPP MPPE Compression module registered [ 3.070000] NET: Registered protocol family 24 [ 3.650000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.660000] ehci-pci: EHCI PCI platform driver [ 3.660000] uhci_hcd: USB Universal Host Controller Interface driver [ 3.670000] usbcore: registered new interface driver usb-storage [ 3.680000] usbcore: registered new interface driver ums-alauda [ 3.680000] usbcore: registered new interface driver ums-datafab [ 3.690000] usbcore: registered new interface driver ums-freecom [ 3.690000] usbcore: registered new interface driver ums-jumpshot [ 3.700000] usbcore: registered new interface driver ums-sddr09 [ 3.710000] usbcore: registered new interface driver ums-sddr55 [ 3.710000] usbcore: registered new interface driver ums-usbat [ 3.720000] mousedev: PS/2 mouse device common for all mice [ 3.720000] [gptu] { setrate : 154 }cpu_clk 200000000 [ 3.730000] [gptu] { setrate : 158 }reload_counter_value 1 [ 3.730000] gpio-sso-xrx500 16d00000.sso: pins are not configured from the driver [ 3.740000] gpio-sso-xrx500 16d00000.sso: Init done [ 3.750000] Device IRQ: 97 line: 101 [ 3.750000] GlobalControl97_Capabilities_Get [ 3.750000] EIP202: PEs=1 rings=4 64-bit=No, fill level extension=No [ 3.750000] CF size=4 RF size=3 DMA len = 10 Align=0 HDW=0 HostIfc=3 [ 3.770000] EIP96 options: [ 3.770000] AES: Yes with CFB/OFB: Yes Fast: Yes [ 3.770000] DES: Yes with CFB/OFB: Yes Fast: No [ 3.770000] ARCFOUR level: 3 [ 3.770000] MD5: Yes SHA1: Yes Fast: Yes SHA256: Yes SHA512: Yes [ 3.770000] (X)CBC-MAC: Yes Fast: Yes All key sizes: No GHASH Yes [ 3.790000] EIP97 options: PEs=1, In Dbuf size=6 In Tbuf size=5, Out Dbuf size=6, Out Tbuf size=4, [ 3.790000] Token Generator: No, Transform Record Cache: No [ 3.810000] EIP206 options: PE type=0 InClassifier=0 OutClassifier=0 MAC chans=0 [ 3.810000] InDBuf=0kB InTBuf=0kB OutDBuf=0kB OutTBuf=0kB [ 3.820000] Global EIP-97 capabilities: EIP-97 v1.2p1 with EIP-202 v1.3p0 and EIP-96 v2.2p3, #PE=01 #rings=04 [ 3.830000] Global Status of the EIP-97 [ 3.830000] Packet Engine 0 Status [ 3.840000] DFE Status: CD FIFO Words: 0, CDR ID: 15, DMA size: 0 [ 3.840000] AtDMA busy: false, DataDMA busy: false, DMA err: false [ 3.850000] DSE Status: RD FIFO Words: 0, RDR ID: 15, DMA size: 0 [ 3.850000] Data flush busy: false, DataDMA busy: false, DMA err: false [ 3.860000] Token Status: Active: 0, loc available: true [ 3.860000] res available: false, read active: false, ccache active: false [ 3.860000] cntx fetch: false, res cntx: false [ 3.860000] processing held: true, busy: false [ 3.880000] Context Status: Err mask: 0000, Available: 0 [ 3.880000] Active cntx: false, next cntx: false, result cntx: false Err recov: false [ 3.900000] Interrupt Status: input DMA err: false, output DMA err false [ 3.900000] pkt proc err: false, pkt timeout: false, f a t a l err: false, PE int out: false [ 3.900000] inp DMA enable: false, outp DMA enable false, pkt proc enable: false [ 3.900000] pkt timeout enable: false, f a t a l enable: false,PE int out enable: false [ 3.930000] Output Transfer Status: availabe: 71, min: 8, max: 64, size mask: 252 [ 3.940000] PRNG Status: busy: true, res ready: false [ 3.940000] Adapter_Lock_Alloc: Lock = spinlock [ 3.940000] Adapter_Lock_Alloc: Lock = spinlock [ 3.950000] Adapter_PECDev_Init: CDR fetch size 0x8, thresh 0x6, HDW=0, CFsize=4 [ 3.960000] Adapter_PECDev_Init: RDR fetch size 0x8, thresh 0x2, RFsize=3 [ 3.960000] Status of CDR/RDR interface 0 [ 3.970000] CDR Status: DMA err: false, err: false: ovf/under err: false [ 3.970000] Threshold int: false, timeout int: false, FIFO count: 16 [ 3.980000] RDR Status: DMA err: false, err: false: ovf/under err: false [ 3.980000] Buf ovf: false, Descriptor ovf false [ 3.980000] Threshold int: false, timeout int: false, FIFO count: 8 [ 4.000000] LTQ Crypto Hardware Initialized .. [ 4.010000] LTQ crypto driver version: 1.2.37 [ 4.010000] usbcore: registered new interface driver usbhid [ 4.010000] usbhid: USB HID core driver [ 4.020000] u32 classifier [ 4.020000] input device check on [ 4.020000] Actions configured [ 4.030000] nf_conntrack version 0.5.0 (7022 buckets, 28088 max) [ 4.030000] nf_conntrack_rtsp v0.6.21 loading [ 4.040000] NF_TPROXY: Transparent proxy support initialized, version 4.1.0 [ 4.050000] NF_TPROXY: Copyright (c) 2006-2007 BalaBit IT Ltd. [ 4.050000] xt_time: kernel timezone is -0000 [ 4.060000] ipip: IPv4 over IPv4 tunneling driver [ 4.060000] nf_nat_rtsp v0.6.21 loading [ 4.060000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 4.070000] TCP: cubic registered [ 4.070000] Initializing XFRM netlink socket [ 4.080000] NET: Registered protocol family 10 [ 4.080000] NET: Registered protocol family 17 [ 4.090000] NET: Registered protocol family 15 [ 4.090000] Bridge firewalling registered [ 4.090000] Ebtables v2.0 registered [ 4.100000] lec:lane_module_init: lec.c: initialized [ 4.100000] mpoa:atm_mpoa_init: mpc.c: initialized [ 4.110000] KOAM is loaded successfully. [ 4.110000] l2tp_core: L2TP core driver, V2.0 [ 4.120000] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 4.120000] l2tp_netlink: L2TP netlink interface [ 4.130000] 8021q: 802.1Q VLAN Support v1.8 [ 4.130000] UBI: attaching mtd5 to ubi0 [ 8.630000] UBI: scanning is finished [ 8.660000] UBI: attached mtd5 (name "system_sw", size 246 MiB) to ubi0 [ 8.660000] UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 8.670000] UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 8.680000] UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 8.680000] UBI: good PEBs: 1967, bad PEBs: 1, corrupted PEBs: 0 [ 8.690000] UBI: user volume: 7, internal volumes: 1, max. volumes count: 128 [ 8.700000] UBI: max/mean erase counter: 2148/1134, WL threshold: 4096, image sequence number: 2100855820 [ 8.710000] UBI: available PEBs: 955, total reserved PEBs: 1012, PEBs reserved for bad PEB handling: 39 [ 8.720000] UBI: background thread "ubi_bgt0d" started, PID 521 [ 8.720000] Gluebi: mtd 'rootfsA' set to be root filesystem [ 8.730000] drivers/rtc/hctosys.c: unable to open rtc dev[ 8.750000] VFS: Mounted root (squashfs filesystem) readonly on device 31:9. [ 8.760000] Freeing unused memory: 296k freed rootdir=/ table='/etc/device_table.txt' [ 9.620000] init: Console is alive [ 12.640000] init: - preinit - [ 13.510000] UBIFS: background thread "ubifs_bgt0_2" started, PID 799 [ 13.650000] UBIFS: recovery needed [ 14.120000] UBIFS: recovery completed [ 14.120000] UBIFS: mounted UBI device 0, volume 2, name "data_vol" [ 14.130000] UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 14.140000] UBIFS: FS size: 40759296 bytes (38 MiB, 321 LEBs), journal size 2031616 bytes (1 MiB, 16 LEBs) [ 14.150000] UBIFS: reserved for root: 1925161 bytes (1880 KiB) [ 14.150000] UBIFS: media format: w4/r0 (latest is w4/r0), UUID 4C87C7EF-5806-480D-B9FF-4C4A96EF8284, small LPT model [ 14.490000] gphy-fw gphy-fw.9: proc_write_phy_fw: Found:GRX500 V1.1 GPHY BE FW [ 14.500000] gphy-fw gphy-fw.9: booting GPHY0 firmware at 27C20000 for GRX500 [ 14.510000] gphy-fw gphy-fw.9: booting GPHY1 firmware at 27C20000 for GRX500 [ 14.510000] gphy-fw gphy-fw.9: booting GPHY2 firmware at 27C20000 for GRX500 [ 14.520000] gphy-fw gphy-fw.9: booting GPHY3 firmware at 27C20000 for GRX500 [ 14.530000] gphy-fw gphy-fw.9: booting GPHY4 firmware at 27C20000 for GRX500 [ 14.530000] ltq_gphy_firmware_config: fw_mode:11G-FW, no of phys:5,data_ptr:27C20000 /etc/preinit: /etc/preinit.d/load_gphy_firmware_preinit.sh: line 60: can't create /sys/class/leds/xrx500:green:1/brightness: nonexistent directory Enabling GMII SSC ... [ 18.980000] cgroup: mkdir (852) created nested cgroup for controller "memory" which has incomplete hierarchy support. Nested cgroups may change behavior in the future. [ 19.000000] cgroup: "memory" requires setting use_hierarchy to 1 on the root. [ 19.200000] procd: - early - [ 20.910000] procd: - ubus - [ 21.920000] procd: - init - (none) login: [ 22.550000] IFXOS, Version 1.6.9 (c) Copyright 2009, Lantiq Deutschland GmbH [ 22.560000] libsrtp module, Copyright (c) 2001-2006 Cisco Systems, Inc [ 22.570000] http://srtp.sourceforge.net/srtp.html ntgrselfled starting to blink self test led... [ 22.620000] Lantiq kernel event logger, version 1.1.15, (c) 2007-2010 Lantiq Deutschland GmbH [ 22.770000] Registeration is a success The major device number is 247. [ 22.800000] proc initialized [ 23.030000] tun: Universal TUN/TAP device driver, 1.6 [ 23.030000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> [ 23.460000] sit: IPv6 over IPv4 tunneling driver [ 23.680000] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3) [ 23.700000] l2tp_ip: L2TP IP encapsulation support (L2TPv3) [ 23.720000] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3) [ 23.720000] gre: GRE over IPv4 demultiplexor driver [ 23.750000] ip_gre: GRE over IPv4 tunneling driver [ 23.940000] ip6_gre: GRE over IPv6 tunneling driver [ 24.060000] PMAC_EG_CFG_SET for GSW-L [ 24.060000] PMAC_IG_CFG_SET for GSW-L [ 24.070000] PMAC_EG_CFG_SET for GSW-R [ 24.070000] PMAC_IG_CFG_SET for GSW-R [ 24.080000] [ 24.080000] GSW PMAC Init Done!!! [ 24.080000] registering one of MII bus [ 24.140000] libphy: lantiq,xrx500-mdio: probed [ 24.230000] registering PAE MII bus [ 24.250000] libphy: lantiq,xrx500-mdio-pae: probed [ 24.280000] adding the interface: 0 [ 24.280000] [cbm] { cbm_dp_port_alloc : 3384 }flags 0x2 port_id 1 [ 24.280000] [cbm] { cbm_dp_port_alloc : 3396 }1 [ 24.290000] [cbm] { cbm_dp_port_alloc : 3404 }2 [ 24.290000] [cbm] { cbm_dp_port_alloc : 3423 }3 [ 24.300000] [cbm] { cbm_dp_port_alloc : 3426 }4 [ 24.300000] [cbm] { cbm_dp_port_alloc : 3431 }5 [ 24.310000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 6 [ 24.310000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 12 [ 24.320000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 24.330000] [cbm] { cbm_dp_port_alloc : 3518 }disabling q 16 port 6 sch_id 0 [ 24.330000] [cbm] { cbm_dp_port_alloc : 3538 }first time LOOKUP prgrm [ 24.340000] [cbm] { cbm_dp_port_alloc : 3540 }1024 [ 24.340000] [cbm] { cbm_dp_port_alloc : 3545 }port id 1 [ 24.350000] no real internal PHY attached to this interface ! [ 24.360000] xrx500_of_iface: rx csum offload is enabled ! [ 24.410000] adding the interface: 1 [ 24.420000] [cbm] { cbm_dp_port_alloc : 3384 }flags 0x2 port_id 2 [ 24.420000] [cbm] { cbm_dp_port_alloc : 3396 }1 [ 24.430000] [cbm] { cbm_dp_port_alloc : 3404 }2 [ 24.430000] [cbm] { cbm_dp_port_alloc : 3423 }3 [ 24.440000] [cbm] { cbm_dp_port_alloc : 3426 }4 [ 24.440000] [cbm] { cbm_dp_port_alloc : 3431 }5 [ 24.440000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 7 [ 24.450000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 13 [ 24.460000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 24.460000] [cbm] { cbm_dp_port_alloc : 3518 }disabling q 17 port 7 sch_id 1 [ 24.470000] [cbm] { cbm_dp_port_alloc : 3538 }first time LOOKUP prgrm [ 24.480000] [cbm] { cbm_dp_port_alloc : 3540 }1024 [ 24.480000] [cbm] { cbm_dp_port_alloc : 3545 }port id 2 [ 24.490000] xrx500_of_iface: rx csum offload is enabled ! [ 24.490000] trying to connect: eth0_1 to device: 0:02 with irq: 120 [ 24.540000] eth0_1: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:02, irq=120) [ 24.640000] adding the interface: 2 [ 24.640000] [cbm] { cbm_dp_port_alloc : 3384 }flags 0x2 port_id 3 [ 24.650000] [cbm] { cbm_dp_port_alloc : 3396 }1 [ 24.650000] [cbm] { cbm_dp_port_alloc : 3404 }2 [ 24.660000] [cbm] { cbm_dp_port_alloc : 3423 }3 [ 24.660000] [cbm] { cbm_dp_port_alloc : 3426 }4 [ 24.670000] [cbm] { cbm_dp_port_alloc : 3431 }5 [ 24.670000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 8 [ 24.680000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 14 [ 24.680000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 24.690000] [cbm] { cbm_dp_port_alloc : 3518 }disabling q 18 port 8 sch_id 2 [ 24.700000] [cbm] { cbm_dp_port_alloc : 3538 }first time LOOKUP prgrm [ 24.700000] [cbm] { cbm_dp_port_alloc : 3540 }1024 [ 24.710000] [cbm] { cbm_dp_port_alloc : 3545 }port id 3 [ 24.710000] xrx500_of_iface: rx csum offload is enabled ! [ 24.720000] trying to connect: eth0_2 to device: 0:03 with irq: 121 [ 24.770000] eth0_2: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:03, irq=121) [ 24.840000] adding the interface: 3 [ 24.840000] [cbm] { cbm_dp_port_alloc : 3384 }flags 0x2 port_id 4 [ 24.850000] [cbm] { cbm_dp_port_alloc : 3396 }1 [ 24.850000] [cbm] { cbm_dp_port_alloc : 3404 }2 [ 24.860000] [cbm] { cbm_dp_port_alloc : 3423 }3 [ 24.860000] [cbm] { cbm_dp_port_alloc : 3426 }4 [ 24.870000] [cbm] { cbm_dp_port_alloc : 3431 }5 [ 24.870000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 9 [ 24.880000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 15 [ 24.880000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 24.890000] [cbm] { cbm_dp_port_alloc : 3518 }disabling q 19 port 9 sch_id 3 [ 24.900000] [cbm] { cbm_dp_port_alloc : 3538 }first time LOOKUP prgrm [ 24.910000] [cbm] { cbm_dp_port_alloc : 3540 }1024 [ 24.910000] [cbm] { cbm_dp_port_alloc : 3545 }port id 4 [ 24.920000] xrx500_of_iface: rx csum offload is enabled ! [ 24.920000] trying to connect: eth0_3 to device: 0:04 with irq: 134 [ 24.970000] eth0_3: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:04, irq=134) [ 25.080000] adding the interface: 4 [ 25.080000] [cbm] { cbm_dp_port_alloc : 3384 }flags 0x2 port_id 5 [ 25.090000] [cbm] { cbm_dp_port_alloc : 3396 }1 [ 25.090000] [cbm] { cbm_dp_port_alloc : 3404 }2 [ 25.090000] [cbm] { cbm_dp_port_alloc : 3423 }3 [ 25.100000] [cbm] { cbm_dp_port_alloc : 3426 }4 [ 25.100000] [cbm] { cbm_dp_port_alloc : 3431 }5 [ 25.110000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 10 [ 25.110000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 16 [ 25.120000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 25.130000] [cbm] { cbm_dp_port_alloc : 3518 }disabling q 20 port 10 sch_id 4 [ 25.130000] [cbm] { cbm_dp_port_alloc : 3538 }first time LOOKUP prgrm [ 25.140000] [cbm] { cbm_dp_port_alloc : 3540 }1024 [ 25.150000] [cbm] { cbm_dp_port_alloc : 3545 }port id 5 [ 25.150000] xrx500_of_iface: rx csum offload is enabled ! [ 25.160000] trying to connect: eth0_4 to device: 0:05 with irq: 135 [ 25.210000] eth0_4: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=0:05, irq=135) [ 25.270000] adding the interface: 5 [ 25.270000] [cbm] { cbm_dp_port_alloc : 3384 }flags 0x2 port_id 6 [ 25.280000] [cbm] { cbm_dp_port_alloc : 3396 }1 [ 25.280000] [cbm] { cbm_dp_port_alloc : 3404 }2 [ 25.280000] [cbm] { cbm_dp_port_alloc : 3423 }3 [ 25.290000] [cbm] { cbm_dp_port_alloc : 3426 }4 [ 25.290000] [cbm] { cbm_dp_port_alloc : 3431 }5 [ 25.300000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 11 [ 25.300000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 17 [ 25.310000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 25.320000] [cbm] { cbm_dp_port_alloc : 3518 }disabling q 21 port 11 sch_id 5 [ 25.330000] [cbm] { cbm_dp_port_alloc : 3538 }first time LOOKUP prgrm [ 25.330000] [cbm] { cbm_dp_port_alloc : 3540 }1024 [ 25.340000] [cbm] { cbm_dp_port_alloc : 3545 }port id 6 [ 25.340000] no real internal PHY attached to this interface ! [ 25.350000] xrx500_of_iface: rx csum offload is enabled ! [ 25.380000] adding the interface: 6 [ 25.380000] [cbm] { cbm_dp_port_alloc : 3384 }flags 0x4 port_id 15 [ 25.390000] [cbm] { cbm_dp_port_alloc : 3396 }1 [ 25.390000] [cbm] { cbm_dp_port_alloc : 3404 }2 [ 25.400000] [cbm] { cbm_dp_port_alloc : 3423 }3 [ 25.400000] [cbm] { cbm_dp_port_alloc : 3426 }4 [ 25.410000] [cbm] { cbm_dp_port_alloc : 3431 }5 [ 25.410000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 19 [ 25.420000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 25.420000] [cbm] { cbm_dp_port_alloc : 3518 }disabling q 28 port 19 sch_id 12 [ 25.430000] [cbm] { cbm_dp_port_alloc : 3538 }first time LOOKUP prgrm [ 25.440000] [cbm] { cbm_dp_port_alloc : 3540 }1024 [ 25.440000] [cbm] { cbm_dp_port_alloc : 3545 }port id 15 [ 25.450000] xrx500_of_iface: rx csum offload is enabled ! [ 25.450000] trying to connect: eth1 to device: 1:01 with irq: 119 [ 25.500000] eth1: attached PHY [Lantiq XWAY VR9 GPHY 11G v1.4] (phy_addr=1:01, irq=119) [ 25.560000] register mc group pass: 0, grp name: eth_mcgrp, grp id:1 [ 25.570000] Lantiq ethernet driver for XRX500 ! [ 25.700000] PPA API --- init successfully [ 25.770000] TMU HAL Init. [ 25.770000] Total node : 544 and size of each node: 7336 [ 25.770000] Total allocated size=3990784 [ 25.790000] Total node : 544 and size of each node: 7336 [ 25.810000] <hal_init> Number of CPU TMU Ports are:1 [ 25.810000] <hal_init> CPU TMU resources are Port:2 ,SB:19, Q:35 [ 25.820000] <hal_init> Number of MPE TMU Ports are:1 [ 25.820000] <hal_init> MPE TMU resources are Port:3 ,SB:20, Q:36 [ 25.830000] TMU HAL Init. [ 25.830000] Done!! [ 25.850000] Lantiq directpath datapath driver for XRX500, version lantiq_directpath_drv_xrx500.c:v1.1.1 [ 25.850000] ,(c)2009 Lantiq AG [ 26.020000] Genconf offset correct [ 26.080000] Min TC:1 Max TC:4 [ 26.080000] [vmb_cpu_alloc]:[594] CPU vpet[j].cpu_status = 11 [ 26.080000] [vmb_yr_get]:[1372] CPU = 3, yri[i].yr_status = 1, yield_bits = 2 n_yr = 1 yri[i].cpu_id = 3 [ 26.090000] [fw_vmb_get_irq]:[1475] CPU = 3 IRQ = 110 !!! [ 26.100000] [vmb_tc_alloc]:[948] CPU tct[i].tc_status = 1 [ 26.100000] [vmb_yr_get]:[1372] CPU = 3, yri[i].yr_status = 1, yield_bits = 4 n_yr = 1 yri[i].cpu_id = 3 [ 26.110000] [fw_vmb_get_irq]:[1475] CPU = 3 IRQ = 110 !!! [ 26.120000] mpe_hal_to_vmb_callback_hdlr not support status 0x0 [ 26.130000] [vmb_cpu_start]:[849] vmb_fw_msg_t = a0000218 cpu = 3 vmb_msg_size = b0 sizeof(VMB_fw_msg_t) = 168 sizeof(FW_vmb_msg_t) = 8 !!!! [gic_trigger]:[559] VMB_CPU_IPI3 - 85 CPU = 3 Outs.de WAIT [ot IcI interrupt t2 launcI frFmR Ru 03 MSG_Iv = 01akeup_[ 26.160000] [fw_vmb_ipi3_hdlr]:[166] CPU = 0 irq = 110 [ 26.160000] [fw_vmb_ipi3_hdlr]:[173] cid = 1 , vid = 1 [ 26.160000] [fw_vmb_ipi3_hdlr]:[210] [ 26.160000] [fw_vmb_ipi3_hdlr]:[212] [ 26.160000] vmb_wq = 60867918 [vmb_cpu_start]:[908] OUTSIDE WAIT wakeup_vpe = 1 vpet->fw_vmb.status = 1 ACK = 1 cpu = 3 ret1 = 9997 vpet = 608678fc, smp_processor_id() = 0 , vpet->fw_vmb =60867928 !!!! [ 26.190000] [vmb_cpu_start]:[915] ret = 1 [ 26.190000] <mpe_hal_set_fw_connectivity> CPU TMU resources for MPE are Port:3 ,SB:20, Q:36 SLvl:1 [ 26.210000] MPE HAL Run FW success . [ 26.210000] MPE Proc Creation....!!! [ 26.210000] <mpe_hal_set_ipsec_loopback_connectivity> Enter [ 26.230000] add "loopdev0" successfully [ 26.240000] [cbm] { cbm_dp_port_alloc : 3384 }flags 0x40 port_id 0 [ 26.240000] [cbm] { cbm_dp_port_alloc : 3396 }1 [ 26.250000] [cbm] { cbm_dp_port_alloc : 3404 }2 [ 26.250000] [cbm] { cbm_dp_port_alloc : 3442 }port id 7 [ 26.260000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 255 [ 26.260000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 26.270000] [cbm] { cbm_dp_port_alloc : 3489 }no further action required [ 26.280000] <tmu_hal_setup_dp_ingress_connectivity> TMU resources for Checksum is Port:20 ,SB:13, Q:29 SLvl: 1 [ 26.290000] For Loopdev device Q:30 [ 26.290000] Redirect Port 7 is configured [ 26.390000] DC DP [dc_dp_reserve_port:1361] Trying to reserve multiport0=2!!! [ 26.390000] [cbm] { cbm_dp_port_alloc : 3384 }flags 0x0 port_id 0 [ 26.400000] [cbm] { cbm_dp_port_alloc : 3396 }1 [ 26.400000] [cbm] { resv_dp_res : 3085 }even_first 1 [ 26.410000] [cbm] { resv_dp_res : 3095 }Alloc 0x1 resv 0x0 [ 26.410000] [cbm] { resv_dp_res : 3101 }f_found 8 [ 26.420000] [cbm] { resv_dp_res : 3120 }found the pair 9 8 [ 26.420000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 26.430000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 26.440000] DC DP [dc_dp_reserve_port:1389] Successfully reserved multiport0=2 start_port_id=8!!! [ 26.480000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 26.510000] pecostat_noIRQ module loaded [ 26.520000] pecostat LKM installed, version 2.0.2. [ 26.560000] Netfilter messages via NETLINK v0.30. [ 26.570000] ip_set: protocol 6 [ 26.800000] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 26.810000] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 26.810000] xhci_gen_setup() 4767 MSWAP=0 [ 26.820000] xhci_gen_setup() 4768 VERSION=0x0100 [ 26.820000] xhci_gen_setup() 4769 HC_LENGTH=0x20 [ 26.830000] xhci-hcd xhci-hcd.0.auto: irq 91, io mem 0x1a500000 [ 26.830000] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002 [ 26.840000] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 26.850000] usb usb1: Product: xHCI Host Controller [ 26.850000] usb usb1: Manufacturer: Linux 3.10.108 xhci-hcd [ 26.860000] usb usb1: SerialNumber: xhci-hcd.0.auto [ 26.900000] hub 1-0:1.0: USB hub found [ 26.900000] hub 1-0:1.0: 1 port detected [ 26.910000] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 26.910000] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 26.920000] usb usb2: New USB device found, idVendor=1d6b, idProduct=0003 [ 26.930000] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1 [ 26.930000] usb usb2: Product: xHCI Host Controller [ 26.940000] usb usb2: Manufacturer: Linux 3.10.108 xhci-hcd [ 26.940000] usb usb2: SerialNumber: xhci-hcd.0.auto [ 26.960000] hub 2-0:1.0: USB hub found [ 26.960000] hub 2-0:1.0: 1 port detected [ 27.190000] i2c /dev entries driver [ 27.350000] Mirror/redirect action on [ 27.370000] Failed to load ipt action [ 27.540000] netem: version 1.3 No calling Intel ubus event, usb device connected!!! [ 27.690000] usbcore: registered new interface driver cdc_acm [ 27.690000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 27.730000] usbcore: registered new interface driver cdc_wdm [ 27.960000] ctnetlink v0.93: registering with nfnetlink. [ 28.100000] PPTP driver version 0.8.5 [ 28.140000] usbcore: registered new interface driver usblp No calling Intel ubus event, usb device connected!!! [ 28.340000] usbcore: registered new interface driver cdc_ncm [ 28.480000] usbcore: registered new interface driver cdc_mbim [ 29.960000] sysctl: The scan_unevictable_pages sysctl/node-interface has been disabled for lack of a legitimate use case. If you have one, please send an email to linux-mm@kvack.org. failed to open fifo : No such file or directory module is already loaded - ip6_tables module is already loaded - ip6table_filter module is already loaded - ip6t_REJECT conntrack v1.0.0 (conntrack-tools): 0 flow entries have been deleted. set mcast listen ok 1970-01-01 09:00:41: (configfile.c.59) Warning: please add "mod_openssl" to server.modules list in lighttpd.conf. A future release of lighttpd 1.4.x *will not* automatically load mod_openssl and lighttpd *will not* use SSL/TLS where your lighttpd.conf contains ssl.* directives 1970-01-01 09:00:41: (network.c.294) warning: server.set-v6only will be removed soon, update your config to have different sockets for ipv4 and ipv6 1970-01-01 09:00:41: (server.c.1525) server started (lighttpd/1.4.47) 1970-01-01 09:00:41: (network.c.294) warning: server.set-v6only will be removed soon, update your config to have different sockets for ipv4 and ipv6 1970-01-01 09:00:41: (server.c.1525) server started (lighttpd/1.4.47) Options error: In [CMD-LINE]:1: Error opening configuration file: /tmp/openvpn/server_tun.conf Use --help for more information. Options error: In [CMD-LINE]:1: Error opening configuration file: /tmp/openvpn/server_tap.conf Use --help for more information. Warning: never matched protocol: 51. use extension match instead. Warning: never matched protocol: 51. use extension match instead. sCommand=iptables -t nat -L POSTROUTING -v | grep ' MASQUERADE all' | awk -F ' ' '{printf ("%s\n",$7)}' 2> /dev/null ln: /tmp/debug_level: File exists Options error: In [CMD-LINE]:1: Error opening configuration file: /tmp/openvpn/server_tun.conf Use --help for more information. Options error: In [CMD-LINE]:1: Error opening configuration file: /tmp/openvpn/server_tap.conf Use --help for more information. <01-01-1970 09:00:48> [CRITICAL] SERVD {servd_startSlLibsInit, 327}: SL init of SL Library 'sl_FirewallNAT' completed in 16.666000 seconds sh: write error: Device or resource busy sh: write error: Device or resource busy sh: write error: Device or resource busy /bin/sh: can't create /sys/class/gpio/gpio0/direction: nonexistent directory sh: write error: Device or resource busy /bin/sh: can't create /sys/class/gpio/gpio11/direction: nonexistent directory sh: write error: Device or resource busy /bin/sh: can't create /sys/class/gpio/gpio30/direction: nonexistent directory [ 48.520000] Init Success [ 48.520000] [ltq_mpe_hal_drv] { mpe_hal_generic_hook : 575 }ppa_hal_generic_hook not support cmd 0xd [ 48.530000] [ltq_mpe_hal_drv] { mpe_hal_generic_hook : 575 }ppa_hal_generic_hook not support cmd 0xd [ 48.550000] directpath start id: 0, end id: 272 [ 48.550000] ppa_init - init succeeded module is already loaded - macvlan /bin/sh: syntax error: unexpected "(" netifd_ubus_init(1154): connected as 4b7a22ce grep: /tmp/resolv.conf.auto: No such file or directory proto_shell_add_handler(908): Add handler for script ./6rd.sh: 6rd proto_shell_add_handler(908): Add handler for script ./6to4.sh: 6to4 proto_shell_add_handler(908): Add handler for script ./auto.sh: auto iptables: No chain/target/match by that name. netlink recv: No buffer space available proto_shell_add_handler(908): Add handler for script ./dhcp.sh: dhcp ln: /tmp/debug_level: File exists proto_shell_add_handler(908): Add handler for script ./dhcpv6.sh: dhcpv6 proto_shell_add_handler(908): Add handler for script ./l2tp.sh: l2tp [ 51.090000] [cbm] { cbm_dp_enable : 3853 }******************ep=2 tmu_port=7 queue=17 sid=1 [ 51.100000] [cbm] { cbm_dp_enable : 3884 }enable queue 17 [ 51.100000] [cbm] { cbm_dp_enable : 3885 }flag 1 refcnt 1024 [ 51.110000] p2p channel turned ON ! [ 51.120000] resume phy for device: eth0_1 [ 51.120000] IPv6: ADDRCONF(NETDEV_UP): eth0_1: link is not ready [ 51.130000] [cbm] { cbm_dp_enable : 3853 }******************ep=3 tmu_port=8 queue=18 sid=2 [ 51.140000] [cbm] { cbm_dp_enable : 3884 }enable queue 18 [ 51.140000] [cbm] { cbm_dp_enable : 3885 }flag 1 refcnt 1024 [ 51.150000] p2p channel already ON ! [ 51.150000] resume phy for device: eth0_2 [ 51.160000] IPv6: ADDRCONF(NETDEV_UP): eth0_2: link is not ready [ 51.190000] [cbm] { cbm_dp_enable : 3853 }******************ep=4 tmu_port=9 queue=19 sid=3 [ 51.200000] [cbm] { cbm_dp_enable : 3884 }enable queue 19 [ 51.200000] [cbm] { cbm_dp_enable : 3885 }flag 1 refcnt 1024 [ 51.210000] p2p channel already ON ! [ 51.210000] resume phy for device: eth0_3 [ 51.220000] IPv6: ADDRCONF(NETDEV_UP): eth0_3: link is not ready Pega DIL mo[ 51.240000] [cbm] { cbm_dp_enable : 3853 }******************ep=5 tmu_port=10 queue=20 sid=4 [ 51.250000] [cbm] { cbm_dp_enable : 3884 }enable queue 20 [ 51.250000] [cbm] { cbm_dp_enable : 3885 }flag 1 refcnt 1024 [ 51.260000] p2p channel already ON ! [ 51.260000] resume phy for device: eth0_4 nitor daemon start [ 51.270000] IPv6: ADDRCONF(NETDEV_UP): eth0_4: link is not ready [ 51.290000] [cbm] { cbm_dp_enable : 3853 }******************ep=15 tmu_port=19 queue=28 sid=12 [ 51.300000] [cbm] { cbm_dp_enable : 3884 }enable queue 28 [ 51.300000] [cbm] { cbm_dp_enable : 3885 }flag 1 refcnt 1024 [ 51.310000] p2p channel already ON ! [ 51.310000] resume phy for device: eth1 [ 51.320000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready proto_shell_add_handler(908): Add handler for script ./map.sh: map Check original Access Control Database DAL callback function init proto_shell_add_handler(908): Add handler for script ./ppp.sh: ppp proto_shell_add_handler(908): Add handler for script ./ppp.sh: pppoe proto_shell_add_handler(908): Add handler for script ./ppp.sh: pppoa proto_shell_add_handler(908): Add handler for script ./ppp.sh: pptp proto_shell_add_handler(908): Add handler for script ./wwan.sh: wwan [ 52.410000] [cbm] { cbm_dp_enable : 3853 }******************ep=2 tmu_port=7 queue=17 sid=1 [ 52.420000] [cbm] { cbm_dp_enable : 3884 }enable queue 17 [ 52.430000] [cbm] { cbm_dp_enable : 3885 }flag 0 refcnt 1024 [ 52.450000] [cbm] { cbm_dp_enable : 3853 }******************ep=3 tmu_port=8 queue=18 sid=2 [ 52.460000] [cbm] { cbm_dp_enable : 3884 }enable queue 18 [ 52.460000] [cbm] { cbm_dp_enable : 3885 }flag 0 refcnt 1024 ln: /opt/lantiq/usr/sbin/fapiToolBox: File exists[ 52.490000] [cbm] { cbm_dp_enable : 3853 }******************ep=4 tmu_port=9 queue=19 sid=3 [ 52.500000] [cbm] { cbm_dp_enable : 3884 }enable queue 19 [ 52.500000] [cbm] { cbm_dp_enable : 3885 }flag 0 refcnt 1024 [ 52.520000] [cbm] { cbm_dp_enable : 3853 }******************ep=5 tmu_port=10 queue=20 sid=4 [ 52.530000] [cbm] { cbm_dp_enable : 3884 }enable queue 20 [ 52.530000] [cbm] { cbm_dp_enable : 3885 }flag 0 refcnt 1024 [ 52.550000] [cbm] { cbm_dp_enable : 3853 }******************ep=15 tmu_port=19 queue=28 sid=12 [ 52.560000] [cbm] { cbm_dp_enable : 3884 }enable queue 28 [ 52.570000] [cbm] { cbm_dp_enable : 3885 }flag 0 refcnt 1024 ln: /opt/lantiq/usr/sbin/sigmas: File exists ln: /opt/lantiq/usr/sbin/sigma-ap.sh: File exists ln: /opt/lantiq/usr/sbin/sigma-run.sh: File exists Options error: In [CMD-LINE]:1: Error opening configuration file: /tmp/openvpn/server_tun.conf Use --help for more information. ls: /overlay/opt/lantiq/wave/scripts/: No such file or directory Options error: In [CMD-LINE]:1: Error opening configuration file: /tmp/openvpn/server_tap.co[ 52.670000] [cbm] { cbm_dp_enable : 3853 }******************ep=2 tmu_port=7 queue=17 sid=1 [ 52.680000] [cbm] { cbm_dp_enable : 3884 }enable queue 17 [ 52.680000] [cbm] { cbm_dp_enable : 3885 }flag 1 refcnt 1024 [ 52.690000] p2p channel already ON ! [ 52.690000] phy init already done ! [ 52.700000] IPv6: ADDRCONF(NETDEV_UP): eth0_1: link is not ready nf Use --help for more information. ioctl error: No such device [ 52.730000] device eth0_1 entered promiscuous mode ##### WORKAROND: ##################### ##### ##### WORKAROND: DISABLE eth_bond_init ##### ##### WORKAROND: ##################### ##### / ##### md5confs.cs exist md5confs_ret=0 ##### ##### FAST BOOT MODE ##### ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_hw_init: init flow with conf from previous setting - FAST BOOT FAPI Recovery Daemon started netlink recv: No buffer space available /opt/lantiq/wave/scripts/fapi_wlan_wave_hw_init: Disable voltage scaling in PMCU /opt/lantiq/wave/scripts/fapi_wlan_wave_hw_init CONFIG_IFX_CONFIG_CPU = GRX500 /opt/lantiq/wave/scripts/fapi_wlan_wave_hw_init CONFIG_IFX_MODEL_NAME = GRX350_1600_MR_AXEPOINT_6X_WAV600_ETH_RT_74 Update d2 ... pudild wait recvmsg fapi_wlan_wave_discover.sh: ALL PCI DEVICES COUNT: 4 fapi_wlan_[ 53.800000] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready wave_discover.sh: WLAN PCI DEVICES COUNT: 2 [ 53.810000] [cbm] { cbm_dp_enable : 3853 }******************ep=3 tmu_port=8 queue=18 sid=2 [ 53.820000] [cbm] { cbm_dp_enable : 3884 }enable queue 18 [ 53.820000] [cbm] { cbm_dp_enable : 3885 }flag 1 refcnt 1024 [ 53.830000] p2p channel already ON ! [ 53.830000] phy init already done ! [ 53.840000] IPv6: ADDRCONF(NETDEV_UP): eth0_2: link is not ready [ 53.850000] device eth0_2 entered promiscuous mode [ 53.870000] [cbm] { cbm_dp_enable : 3853 }******************ep=4 tmu_port=9 queue=19 sid=3 [ 53.880000] [cbm] { cbm_dp_enable : 3884 }enable queue 19 [ 53.880000] [cbm] { cbm_dp_enable : 3885 }flag 1 refcnt 1024 [ 53.890000] p2p channel already ON ! [ 53.890000] phy init already done ! [ 53.890000] IPv6: ADDRCONF(NETDEV_UP): eth0_3: link is not ready [ 53.910000] device eth0_3 entered promiscuous mode [ 53.910000] [cbm] { cbm_dp_enable : 3853 }******************ep=5 tmu_port=10 queue=20 sid=4 [ 53.920000] [cbm] { cbm_dp_enable : 3884 }enable queue 20 [ 53.930000] [cbm] { cbm_dp_enable : 3885 }flag 1 refcnt 1024 [ 53.930000] p2p channel already ON ! [ 53.940000] phy init already done ! [ 53.940000] IPv6: ADDRCONF(NETDEV_UP): eth0_4: link is not ready [ 53.960000] device eth0_4 entered promiscuous mode [ 53.960000] [cbm] { cbm_dp_enable : 3853 }******************ep=15 tmu_port=19 queue=28 sid=12 [ 53.970000] [cbm] { cbm_dp_enable : 3884 }enable queue 28 [ 53.980000] [cbm] { cbm_dp_enable : 3885 }flag 1 refcnt 1024 [ 53.980000] p2p channel already ON ! [ 53.990000] phy init already done ! [ 53.990000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready [ 55.050000] device eth1 entered promiscuous mode [ 55.050000] IPv6: ADDRCONF(NETDEV_UP): eth1_w32: link is not ready fapi_wlan_wave_discover.sh: AHB_WLAN_COUNT: 0 /opt/lantiq/wave/scripts/fapi_wlan_wave_hw_init:TBD disable AHB only for gen6 driver- WAVE600:AHB_WLAN_COUNT=0 fapi_wlan_wave_discover.sh ( WAVE600 driver has no AHB support): TOTAL WLAN COUNT: 2 FAPIWAVESCRIPTS ATTENTION ATTENTION /opt/lantiq/wave/scripts/fapi_wlan_wave_hw_init:########################################### FAPIWAVESCRIPTS ATTENTION ATTENTION /opt/lantiq/wave/scripts/fapi_wlan_wave_hw_init:chipids: card0=09d0 card1=09d0 card2= FAPIWAVESCRIPTS ATTENTION ATTENTION /opt/lantiq/wave/scripts/fapi_wlan_wave_hw_init:#### init flow with conf from previous setting - FAST BOOT FAPIWAVESCRIPTS ATTENTION ATTENTION /opt/lantiq/wave/scripts/fapi_wlan_wave_hw_init:########################################### [ 55.770000] udevd[5842]: starting version 173 [ 55.870000] Loading modules backported from Linux version v5.1-e93c9c99a629c61837d5a7fc2120cd2b6c70dbdd [ 55.880000] Backport generated by backports.git v3.10.108 [ 56.440000] [MTLKD] Allocated netdev rtlog0 addr 75891800 [ 56.440000] [4294942940] mtlk0(mtlk_cdev_init:311): Max nodes set to 1048575 netlink recv: No buffer space available Options error: In [CMD-LINE]:1: Error opening configuration file: /tmp/openvpn/server_tap.conf Use --help for more information. Options error: In [CMD-LINE]:1: Error opening configuration file: /tmp/openvpn/server_tun.conf Use --help for more information. Inlcuding modules needed for mwan3 ... bootcheck Last shutdown is unknown or kernel crash!! ntgr_wifischedule is starting... grep: /tmp/memUsage_in_1440mins.dat: No such file or directory sh: bad number [ 62.600000] ltq_temp: Lantiq Temperature Sensor Driver, Version 1.1.2 (c) Copyright 2014, Lantiq Deutschland GmbH nvram reload... Options error: In [CMD-LINE]:1: Error opening configuration file: /tmp/openvpn/server_tap.conf Use --help for more information. Options error: In [ 62.900000] ltq_pmcu: PMCU Lantiq Power Management Control Unit, Version 1.3.6 (c) Copyright 2014, Lantiq Deutschland GmbH [ 71.370000] [4294944433] mtlk0(__mtlk_print_endianess:10211): The system is Big endian (0xbeadfeed, 0xedfeadbe) [ 71.380000] [4294944434] mtlk0(__mtlk_print_driver_version:10218): Driver version: 6.1.0_bp.0.27.bfbd5bc5bc82a779ff78e1a2dea9f2b4bc78aa4d.PcieG5.PcieG6.Release [ 71.390000] [4294944435] mtlk0(mtlk_fast_mem_print_info:115): Using normal memory for hot context [ 71.400000] PCI: Enabling device 0000:01:00.0 (0000 -> 0002) [ 71.410000] [4294944437] mtlk0(_pci_mem_get:611): PCI Memory block 0: PA: 0xb8000000, VA: 0xf8000000, Len=0x2000000 [ 71.420000] [MTLKD] PCIE bus ChipVersion:A0 ChipID is:0x0900 address is:0xf8220060 [ 71.420000] [4294944438] mtlkW(_pci_start:706): CID-00: Detecting DUAL PCI mode... [ 71.430000] [MTLKD] RCU_BOOT: 0x00003007, mspsStatus: 0x00, address: 0xf827000c [ 71.440000] [MTLKD] DUAL PCI mode is detected [ 71.440000] [MTLKD] PCIE bus ChipVersion:A0 ChipID is:0x0900 address is:0xf8220060 [ 71.450000] [MTLKD] PCIE bus ChipVersion:A0 ChipID is:0x0900 address is:0xf8220060 [ 71.460000] [4294944442] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('cal_wlan0.bin') is starting [ 71.510000] [4294944447] mtlk0(_eeprom_parse:590): EEPROM info: ver 0x0600, cal_file_type Operational, device_id 0x0900, header size 40, data size 1024, is_cis_v6 1 [ 71.520000] [4294944448] mtlk0(mtlk_cis_data_parse:857): EEPROM Card ID: type 0x61, revision 0x45 (E) [ 71.530000] [4294944449] mtlk0(_mtlk_cis_search_and_parse_rssi_v6:787): RSSI CIS found ant_mask 0x0A, freq 5570, band 0 [ 71.540000] [4294944450] mtlk0(_mtlk_cis_search_and_parse_rssi_v6:787): RSSI CIS found ant_mask 0x05, freq 2442, band 1 [ 71.550000] [4294944451] mtlk0(_parse_tpc_g6:597): TPC data for chan 36, bw 0, antenna 1 [ 71.560000] [4294944452] mtlk0(_parse_tpc_g6:597): TPC data for chan 36, bw 0, antenna 3 [ 71.570000] [4294944453] mtlk0(_parse_tpc_g6:597): TPC data for chan 52, bw 0, antenna 1 [ 71.570000] [4294944453] mtlk0(_parse_tpc_g6:597): TPC data for chan 52, bw 0, antenna 3 [ 71.580000] [4294944454] mtlk0(_parse_tpc_g6:597): TPC data for chan 100, bw 0, antenna 1 [ 71.590000] [4294944455] mtlk0(_parse_tpc_g6:597): TPC data for chan 100, bw 0, antenna 3 [ 71.600000] [4294944456] mtlk0(_parse_tpc_g6:597): TPC data for chan 116, bw 0, antenna 1 [ 71.610000] [4294944457] mtlk0(_parse_tpc_g6:597): TPC data for chan 116, bw 0, antenna 3 [ 71.620000] [4294944458] mtlk0(_parse_tpc_g6:597): TPC data for chan 132, bw 0, antenna 1 [ 71.620000] [4294944458] mtlk0(_parse_tpc_g6:597): TPC data for chan 132, bw 0, antenna 3 [ 71.630000] [4294944459] mtlk0(_parse_tpc_g6:597): TPC data for chan 149, bw 0, antenna 1 [ 71.640000] [4294944460] mtlk0(_parse_tpc_g6:597): TPC data for chan 149, bw 0, antenna 3 [ 71.650000] [4294944461] mtlk0(_parse_tpc_g6:597): TPC data for chan 36, bw 1, antenna 1 [ 71.660000] [4294944462] mtlk0(_parse_tpc_g6:597): TPC data for chan 36, bw 1, antenna 3 [ 71.660000] [4294944462] mtlk0(_parse_tpc_g6:597): TPC data for chan 52, bw 1, antenna 1 [ 71.670000] [4294944463] mtlk0(_parse_tpc_g6:597): TPC data for chan 52, bw 1, antenna 3 [ 71.680000] [4294944464] mtlk0(_parse_tpc_g6:597): TPC data for chan 100, bw 1, antenna 1 [ 71.690000] [4294944465] mtlk0(_parse_tpc_g6:597): TPC data for chan 100, bw 1, antenna 3 [ 71.700000] [4294944466] mtlk0(_parse_tpc_g6:597): TPC data for chan 116, bw 1, antenna 1 [ 71.700000] [4294944466] mtlk0(_parse_tpc_g6:597): TPC data for chan 116, bw 1, antenna 3 [ 71.710000] [4294944467] mtlk0(_parse_tpc_g6:597): TPC data for chan 132, bw 1, antenna 1 [ 71.720000] [4294944468] mtlk0(_parse_tpc_g6:597): TPC data for chan 132, bw 1, antenna 3 [ 71.730000] [4294944469] mtlk0(_parse_tpc_g6:597): TPC data for chan 149, bw 1, antenna 1 [ 71.740000] [4294944470] mtlk0(_parse_tpc_g6:597): TPC data for chan 149, bw 1, antenna 3 [ 71.750000] [4294944471] mtlk0(_parse_tpc_g6:597): TPC data for chan 36, bw 2, antenna 1 [ 71.750000] [4294944471] mtlk0(_parse_tpc_g6:597): TPC data for chan 36, bw 2, antenna 3 [ 71.760000] [4294944472] mtlk0(_parse_tpc_g6:597): TPC data for chan 52, bw 2, antenna 1 [ 71.770000] [4294944473] mtlk0(_parse_tpc_g6:597): TPC data for chan 52, bw 2, antenna 3 [ 71.780000] [4294944474] mtlk0(_parse_tpc_g6:597): TPC data for chan 100, bw 2, antenna 1 [ 71.790000] [4294944475] mtlk0(_parse_tpc_g6:597): TPC data for chan 100, bw 2, antenna 3 [ 71.790000] [4294944475] mtlk0(_parse_tpc_g6:597): TPC data for chan 116, bw 2, antenna 1 [ 71.800000] [4294944476] mtlk0(_parse_tpc_g6:597): TPC data for chan 116, bw 2, antenna 3 [ 71.810000] [4294944477] mtlk0(_parse_tpc_g6:597): TPC data for chan 132, bw 2, antenna 1 [ 71.820000] [4294944478] mtlk0(_parse_tpc_g6:597): TPC data for chan 132, bw 2, antenna 3 [ 71.830000] [4294944479] mtlk0(_parse_tpc_g6:597): TPC data for chan 149, bw 2, antenna 1 [ 71.840000] [4294944480] mtlk0(_parse_tpc_g6:597): TPC data for chan 149, bw 2, antenna 3 [ 71.840000] [4294944480] mtlk0(_parse_tpc_g6:597): TPC data for chan 36, bw 3, antenna 1 [ 71.850000] [4294944481] mtlk0(_parse_tpc_g6:597): TPC data for chan 36, bw 3, antenna 3 [ 71.860000] [4294944482] mtlk0(_parse_tpc_g6:597): TPC data for chan 100, bw 3, antenna 1 [ 71.870000] [4294944483] mtlk0(_parse_tpc_g6:597): TPC data for chan 100, bw 3, antenna 3 [ 71.880000] [4294944484] mtlk0(_parse_tpc_g6:597): TPC data for chan 7, bw 0, antenna 0 [ 71.880000] [4294944484] mtlk0(_parse_tpc_g6:597): TPC data for chan 7, bw 0, antenna 2 [ 71.890000] [4294944485] mtlk0(_parse_tpc_g6:597): TPC data for chan 5, bw 1, antenna 0 [ 71.900000] [4294944486] mtlk0(_parse_tpc_g6:597): TPC data for chan 5, bw 1, antenna 2 [ 71.910000] [4294944487] mtlk0(_parse_tpc_g6:597): TPC data for chan 7, bw 3, antenna 0 [ 71.920000] [4294944488] mtlk0(_parse_tpc_g6:597): TPC data for chan 7, bw 3, antenna 2 [ 71.920000] [4294944488] mtlk0(_mtlk_cis_area_parse_g6:673): EEPROM: TX antennas number 4, mask 0x0F [ 71.930000] [4294944489] mtlk0(mtlk_cis_data_parse:921): EEPROM supported bands: 2.4 - Yes, 5.2 - Yes [ 71.940000] [4294944490] mtlkW(mtlk_cis_data_parse:924): EEPROM contain TPC data for both bands [ 71.950000] [4294944491] mtlk0(_mtlk_pcieg6_efuse_access_check:1992): eFuse read: addr 0, size 128, buf 0x72d3ff80 [ 71.960000] [4294944492] mtlk0(_mtlk_hw_fill_card_info:3642): is_asic:1, is_emul:0, is_fpga:0, is_phy_dummy:0 [ 71.970000] [4294944493] mtlk0(_wave_hw_cfg_platform_type_set:8051): TestPlatformType: 0 [ 71.980000] [4294944494] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('PSD.bin') is starting [ 72.000000] [4294944496] mtlk0(mtlk_psdb_file_read_and_parse:1963): PSDB Info: version 121 (0x00000079), revision 0100001 [ 72.010000] [4294944497] mtlk0(mtlk_psdb_file_read_and_parse:1972): Look for chip_id 0x0900, hw_type 0x61, hw_rev 0x45 [ 72.020000] [4294944498] mtlk0(psdb_parse_fields_array:1642): Parsed 62 items, found 12 fields and 23 tables [ 72.030000] [4294944499] mtlk0(_mtlk_psdb_parse_ant_mask_per_chan_table:1551): Channel until 35 (including) mask is 0x05 [ 72.040000] [4294944500] mtlk0(_mtlk_psdb_parse_ant_mask_per_chan_table:1551): Channel until 255 (including) mask is 0x0A [ 72.050000] [4294944501] mtlk0(_mtlk_psdb_parse_cdb_cfg_table:1312): CDB config[0] = 1 (CDB_CFG_2G) [ 72.060000] [4294944502] mtlk0(_mtlk_psdb_parse_cdb_cfg_table:1312): CDB config[1] = 2 (CDB_CFG_5G) [ 72.070000] [4294944503] mtlk0(psdb_parse_fields_array:1794): PSDB: TX/RX antennas number 4/4, mask 0x0F/0x0F [ 72.080000] [4294944504] mtlk0(_mtlk_psdb_update_cdb_cfg_table:1478): [0] band 1, channels 1 ... 14 [ 72.090000] [4294944505] mtlk0(_mtlk_psdb_update_cdb_cfg_table:1484): [0] Antennas number 2, mask 05, sel_mask 11, factor 24 [ 72.100000] [4294944506] mtlk0(_mtlk_psdb_update_cdb_cfg_table:1478): [1] band 0, channels 36 ... 165 [ 72.110000] [4294944507] mtlk0(_mtlk_psdb_update_cdb_cfg_table:1484): [1] Antennas number 2, mask 0A, sel_mask 44, factor 24 [ 72.120000] [4294944508] mtlk0(_psdb_print_info:1899): PSDB Beamforming capabilities: 0x1C, bf_explicit=1 [ 72.130000] [4294944509] mtlk0(wave_rcvry_card_add:680): Creating dir FW [ 72.140000] [4294944510] mtlk0(wave_rcvry_card_add:688): Number of files to create 27 [ 72.150000] [4294944511] mtlk0(_mmb_drv_radio_number_get:1427): card_idx:0, number of radios supported:2, configured:2 [ 72.160000] [4294944512] mtlk0(mtlk_hw_mmb_init_card:8096): card_idx:0, mmb_base:0xf8000000, mmb_pas:0xf8300000, mmb_pas_phy:0xb8000000, fastpath supported:1 enabled:1 -> available:1 [ 72.170000] [4294944513] mtlk0(_wave_hw_radio_band_cfg_init:13430): Gen5: 0, Gen6: 1, band_cfg_sys_mode: WAVE_HW_RADIO_BAND_CFG_DB_2x2, ep_mask: 1, vap_mask: 15 [ 72.190000] [4294944515] mtlk0(_wave_hw_radio_band_cfg_init:13436): HW supports max VAPs 16 (32 in FW) max STAs 254 [ 72.200000] [4294944516] mtlk0(wave_radio_limits_set:4665): RadioID 0 supports max VAPs 8 max STAs 127 [ 72.210000] [4294944517] mtlk0(wave_radio_limits_set:4665): RadioID 1 supports max VAPs 8 max STAs 127 [ 72.220000] [4294944518] mtlk0(_wave_hw_dual_pci_mode_set:8037): dual PCI mode ON [ 72.220000] [4294944518] mtlk0(mtlk_df_dcdp_get_host_capability:11408): DC DP library version: 0.0.0 (0x00000000) [ 72.230000] [4294944519] mtlk0(mtlk_df_dcdp_get_host_capability:11411): DC DP headers version: 4.1.4 (0x00040104) [ 72.240000] [4294944520] mtlk0(mtlk_df_dcdp_get_host_capability:11414): FastPath: supported [ 72.250000] [4294944521] mtlk0(mtlk_df_dcdp_get_host_capability:11421): LitePath: supported [ 72.260000] [4294944522] mtlk0(mtlk_df_dcdp_get_host_capability:11422): SWPath: supported [ 72.270000] [4294944523] mtlk0(mtlk_df_dcdp_datapath_dev_init:11460): Activate fragmentation W/A [ 72.280000] [4294944524] mtlk0(pci_irq_alloc:844): CID-00: Interrupt configuration: using legacy interrupt mode [ 72.290000] [4294944525] mtlk0(_mtlk_pcieg6_reset_mac:771): Reset WLAN SOC: address is 0x00270004, value=0x00000001 [ 72.320000] [4294944528] mtlk0(__pcieg6_reset_cpu_lower:719): Reset LMAC0 [ 72.350000] [4294944531] mtlk0(__pcieg6_reset_cpu_lower:719): Reset LMAC1 [ 72.380000] [4294944534] mtlk0(_mtlk_pcieg6_put_cpus_to_reset:801): Reset UMAC [ 72.410000] [4294944537] mtlk0(_mtlk_mmb_cleanup_reset_mac:5343): FW CPU reset is done [ 72.410000] [4294944537] mtlk0(_abb_central_fusing:1253): Trim by AFE data [ 72.420000] [MTLKD] ibiastrim 0x0F [ 72.420000] [MTLKD] vreftrim 0x0A [ 72.430000] [MTLKD] ldo_central_pll1v8 0x03 [ 72.430000] [MTLKD] ldo_central_pllref 0x02 [ 72.440000] [MTLKD] ldo_central_pllpost 0x02 [ 72.440000] [MTLKD] iptattrim 0x0B [ 72.440000] [MTLKD] ldo_central_clkd 0x04 [ 72.450000] [MTLKD] ldo_central_clkin 0x04 [ 72.450000] [MTLKD] (1054) wrToAfeRegC addr 0x0040 value 0x0ABF [ 72.460000] [MTLKD] (1016) FCSI_READ ms 1, rf 0, addr 0x0040, data 0x0080 [ 72.470000] [MTLKD] (1028) FCSI_WRITE ms 1, rf 0, addr 0x0040, data 0x0ABF [ 72.470000] [MTLKD] (1054) wrToAfeRegC addr 0x0045 value 0x0004 [ 72.480000] [MTLKD] (1016) FCSI_READ ms 1, rf 0, addr 0x0045, data 0x0008 [ 72.490000] [MTLKD] (1028) FCSI_WRITE ms 1, rf 0, addr 0x0045, data 0x0004 [ 72.490000] [MTLKD] (1054) wrToAfeRegC addr 0x005E value 0x0003 [ 72.500000] [MTLKD] (1016) FCSI_READ ms 1, rf 0, addr 0x005E, data 0x0004 [ 72.510000] [MTLKD] (1028) FCSI_WRITE ms 1, rf 0, addr 0x005E, data 0x0003 [ 72.510000] [MTLKD] (1054) wrToAfeRegC addr 0x005C value 0x0002 [ 72.520000] [MTLKD] (1016) FCSI_READ ms 1, rf 0, addr 0x005C, data 0x0008 [ 72.530000] [MTLKD] (1028) FCSI_WRITE ms 1, rf 0, addr 0x005C, data 0x0002 [ 72.530000] [MTLKD] (1054) wrToAfeRegC addr 0x005D value 0x0002 [ 72.540000] [MTLKD] (1016) FCSI_READ ms 1, rf 0, addr 0x005D, data 0x0008 [ 72.540000] [MTLKD] (1028) FCSI_WRITE ms 1, rf 0, addr 0x005D, data 0x0002 [ 72.550000] [MTLKD] (1054) wrToAfeRegC addr 0x0047 value 0x0004 [ 72.560000] [MTLKD] (1016) FCSI_READ ms 1, rf 0, addr 0x0047, data 0x0008 [ 72.560000] [MTLKD] (1028) FCSI_WRITE ms 1, rf 0, addr 0x0047, data 0x0004 [ 72.590000] [4294944555] mtlkW(_wave_hw_chi_area_write:4279): hdr 758d0754, id 10 [ 72.590000] [4294944555] mtlkW(_wave_hw_chi_area_write:4285): dst 758d0760, data 0x01 [ 72.600000] [4294944556] mtlkW(_wave_hw_chi_area_write:4285): dst 758d0764, data 0x01 [ 72.610000] [4294944557] mtlkW(_wave_hw_chi_area_write:4285): dst 758d0768, data 0x00 [ 72.610000] [4294944557] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ap_ram_gen6_wrx_600_real_phy.bin') is starting [ 73.450000] [4294944641] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('tx_sender_gen6.bin') is starting [ 73.460000] [4294944642] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('tx_sender_gen6.bin') is starting [ 73.480000] [4294944644] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('host_interface_gen6_dc_mode0.bin') is starting [ 73.500000] [4294944646] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('rx_handler_gen6.bin') is starting [ 73.520000] [4294944648] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('rx_handler_gen6.bin') is starting [ 73.530000] [4294944649] mtlk0(__pcieg6_release_cpu_lower:731): Release LMAC0 [ 73.570000] [4294944653] mtlk0(__pcieg6_release_cpu_lower:731): Release LMAC1 [ 73.610000] [4294944657] mtlk0(_mtlk_pcieg6_release_cpus_reset:1555): Release UMAC [ 73.640000] [4294944660] mtlk0(_mtlk_mmb_wait_chi_magic:4371): Wait for CHI Magic (5000 ms)... [ 73.640000] [4294944660] mtlk0(__log_chi_area:4596): Line 8908: CHI: sFifoQ: is=0x64b0 in=16 rs=0x6470 rn=16 [ 73.650000] [4294944661] mtlk0(__log_chi_area:4596): Line 8909: CHI: sDAT: is=0x50e8 in=1 rs=0x0 rn=0 [ 73.660000] [4294944662] mtlk0(__log_chi_area:4596): Line 8910: CHI: sMAN: is=0x50f0 in=8 rs=0x47cc rn=2 [ 73.670000] [4294944663] mtlk0(__log_chi_area:4596): Line 8911: CHI: sDBG: is=0x4ed8 in=1 rs=0x4cc8 rn=1 [ 73.680000] [4294944664] mtlk0(__log_chi_ring:4616): Line 8913: CHI: sMangTxRING: inCounter=0x2550dc inStatus=0x25512c outCounter=0x25510c outStatus=0x255134 inCounter_BE=0x0 outFreedCounter_BE=0x0 [ 73.700000] [4294944666] mtlk0(__log_chi_ring:4616): Line 8914: CHI: sMangRxRING: inCounter=0x2550d8 inStatus=0x255128 outCounter=0x255108 outStatus=0x255130 inCounter_BE=0x0 outFreedCounter_BE=0x0 [ 73.720000] [4294944668] mtlk0(__log_chi_ring:4616): Line 8916: CHI: sTxRING: inCounter=0x2550cc inStatus=0x25511c outCounter=0x2550fc outStatus=0x255124 inCounter_BE=0x255254 outFreedCounter_BE=0x2359fc [ 73.730000] [4294944669] mtlk0(__log_chi_ring:4616): Line 8917: CHI: sRxRING: inCounter=0x2550c8 inStatus=0x255118 outCounter=0x2550f8 outStatus=0x255120 inCounter_BE=0x255250 outFreedCounter_BE=0x2359f8 [ 73.750000] [4294944671] mtlk0(__log_chi_pool:4629): Line 8918: CHI: sRdPOOL: RdPoolBaseAddress=0x44fb60 RdSizeInBytes=0x20 PayloadAddressOffsetInRd=0x0 BdIndexOffsetInRd=0x1c NumRdsInPool=2048 NumMgtRdsInPool=128 [ 73.770000] [4294944673] mtlk0(_mtlk_pcieg6_ccr_ctrl_ring_init:1766): [Ring Regs] p_IN_cntr:0xf82550e8, p_OUT_status:0xf825513c, p_OUT_cntr:0xf8255114 [ 73.780000] [4294944674] mtlk0(_mtlk_mmb_prepare_ring_counters:4742): [TX Ring Regs] p_IN_cntr:0xf82550cc, p_OUT_status:0xf8255124, p_OUT_cntr:0xf82550fc [ 73.800000] [4294944676] mtlk0(_mtlk_mmb_prepare_ring_counters:4742): [RX Ring Regs] p_IN_cntr:0xf82550c8, p_OUT_status:0xf8255120, p_OUT_cntr:0xf82550f8 [ 73.810000] [4294944677] mtlk0(_mtlk_mmb_prepare_ring_buffer:4777): [RxMgmt Ring] ring_size:128, ring_size_in_bytes:2560 [ 73.820000] [4294944678] mtlk0(_mtlk_mmb_prepare_ring_buffer:4785): [RxMgmt Ring] dma_addr:0x27c16000, base_addr:0xa7c16000 [ 73.830000] [4294944679] mtlk0(_mtlk_mmb_prepare_ring_counters:4742): [RxMgmt Ring Regs] p_IN_cntr:0xf82550d8, p_OUT_status:0xf8255130, p_OUT_cntr:0xf8255108 [ 73.850000] [4294944681] mtlk0(_mtlk_mmb_prepare_ring_buffer:4777): [TxMgmt Ring] ring_size:128, ring_size_in_bytes:2560 [ 73.860000] [4294944682] mtlk0(_mtlk_mmb_prepare_ring_buffer:4785): [TxMgmt Ring] dma_addr:0x27af8000, base_addr:0xa7af8000 [ 73.870000] [4294944683] mtlk0(_mtlk_mmb_prepare_ring_counters:4742): [TxMgmt Ring Regs] p_IN_cntr:0xf82550dc, p_OUT_status:0xf8255134, p_OUT_cntr:0xf825510c [ 73.880000] [4294944684] mtlk0(_mtlk_mmb_init_calibration_cache:5408): u32BufferRequestedSize 127152, pPsdProgmodelAddress 0x0014 [ 73.900000] [4294944686] mtlk0(_mtlk_mmb_allocate_calibration_buffers:5395): Calibration buffer: dma_addr 0x27420000, virt_addr 0x67420000, size 127152 [ 73.910000] [4294944687] mtlk0(wv_cfg80211_init_band:2163): 2.4 GHz band supported, up to 2 spatial streams [ 73.970000] [4294944693] mtlkW(mtlk_vap_manager_get_master_vap:443): Master VAP is not selected [ 73.970000] [4294944693] mtlk0(_wave_radio_vap_create:423): ndev_name wlan0, VapID 0 [ 73.980000] [4294944694] mtlk0(wave_hw_band_hd_ep_bit_get:13514): band_cfg:WAVE_HW_RADIO_BAND_CFG_DB_2x2 RadioID:0 VapID:0 --> ep_bit: 1, vap_id_fw 16 [ 74.000000] [4294944696] mtlk0(_mtlk_df_user_alloc_devname:9273): dev_alloc_name succeeded, pattern:wlan0, name:wlan0 [ 74.130000] [4294944709] mtlk0(wv_cfg80211_init_band:2163): 5 GHz band supported, up to 2 spatial streams [ 74.150000] [4294944711] mtlkW(mtlk_vap_manager_get_master_vap:443): Master VAP is not selected [ 74.150000] [4294944711] mtlk0(_wave_radio_vap_create:423): ndev_name wlan2, VapID 0 [ 74.160000] [4294944712] mtlk0(wave_hw_band_hd_ep_bit_get:13514): band_cfg:WAVE_HW_RADIO_BAND_CFG_DB_2x2 RadioID:1 VapID:0 --> ep_bit: 0, vap_id_fw 0 [ 74.170000] [4294944713] mtlk0(_mtlk_df_user_alloc_devname:9273): dev_alloc_name succeeded, pattern:wlan2, name:wlan2 [ 74.320000] [4294944728] mtlk0(mtlk_hw_mmb_start_card_finalize:8983): mips_no:0, pas_offset:0x0004E868 [ 74.320000] [4294944728] mtlk0(mtlk_hw_mmb_start_card_finalize:8983): mips_no:1, pas_offset:0x0004E86C [ 74.330000] [4294944729] mtlk0(mtlk_hw_mmb_start_card_finalize:8983): mips_no:2, pas_offset:0x0004E870 [ 74.340000] [4294944730] mtlkW(_mtlk_get_rx_ring_size:4834): RX ring size 4096 defined bigger than RD pool size 2048, using RD pool size as ring size [ 74.360000] [4294944732] mtlk0(mtlk_df_dcdp_datapath_dev_register:11633): Registering DirectConnect dev_port 0 [ 74.370000] DC DP [dc_dp_alloc_port:182] owner=72f4745c, dev_port=0, dev=7afbb000, port_id=0, flags=0x00000410 [ 74.380000] [cbm] { cbm_dp_port_alloc : 3384 }flags 0x10008 port_id 8 [ 74.380000] [cbm] { cbm_dp_port_alloc : 3396 }1 [ 74.390000] [cbm] { cbm_dp_port_alloc : 3404 }2 [ 74.390000] [cbm] { cbm_dp_port_alloc : 3423 }3 [ 74.400000] [cbm] { cbm_dp_port_alloc : 3426 }4 [ 74.400000] [cbm] { cbm_dp_port_alloc : 3431 }5 [ 74.400000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 4 [ 74.410000] [cbm] { do_port_setting : 3256 }allocate [ 74.420000] [cbm] { do_port_setting : 3260 }cbm port 4 [ 74.420000] [cbm] { set_wlan_ep : 2934 }set elan ep 8 4 [ 74.430000] [cbm] { cbm_add_to_list : 244 }pmac 8 [ 74.430000] [cbm] { cbm_dp_port_alloc : 3518 }disabling q 32 port 4 sch_id 16 [ 74.440000] [cbm] { cbm_dp_port_alloc : 3538 }first time LOOKUP prgrm [ 74.440000] [cbm] { cbm_dp_port_alloc : 3540 }1024 [ 74.450000] [cbm] { cbm_dp_port_alloc : 3545 }port id 8 [ 74.450000] [cbm] { cbm_dp_port_alloc : 3384 }flags 0x200 port_id 0 [ 74.460000] [cbm] { cbm_dp_port_alloc : 3396 }1 [ 74.470000] [cbm] { cbm_dp_port_alloc : 3404 }2 [ 74.470000] [cbm] { cbm_dp_port_alloc : 3442 }port id 10 [ 74.470000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 20 [ 74.480000] [cbm] { cbm_delete_from_list : 402 }cbm_delete_from_list: flags 0x200 pmac 3000 [ 74.490000] [cbm] { cbm_add_to_list : 289 }Added Successfully cbm_add_to_list [ 74.500000] [cbm] { cbm_dp_port_alloc : 3518 }disabling q 29 port 20 sch_id 13 [ 74.500000] [cbm] { cbm_dp_port_alloc : 3538 }first time LOOKUP prgrm [ 74.510000] [cbm] { cbm_dp_port_alloc : 3540 }1024 [ 74.520000] [cbm] { cbm_dp_port_alloc : 3545 }port id 10 [ 74.520000] [cbm] { cbm_dp_enable : 3853 }******************ep=10 tmu_port=20 queue=29 sid=13 [ 74.530000] [cbm] { cbm_dp_enable : 3884 }enable queue 29 [ 74.530000] [cbm] { cbm_dp_enable : 3885 }flag 1 refcnt 1024 [ 74.540000] DC DP [dc_dp_alloc_port:272] Success, returned port_id=8. [ 74.550000] [4294944751] mtlk0(mtlk_df_dcdp_datapath_dev_register:11644): Registering DirectConnect dev_port 1 [ 74.560000] DC DP [dc_dp_alloc_port:182] owner=72f4745c, dev_port=1, dev=75b74800, port_id=8, flags=0x00000610 [ 74.570000] [cbm] { cbm_dp_port_alloc : 3384 }flags 0x10008 port_id 9 [ 74.570000] [cbm] { cbm_dp_port_alloc : 3396 }1 [ 74.580000] [cbm] { cbm_dp_port_alloc : 3404 }2 [ 74.580000] [cbm] { cbm_dp_port_alloc : 3423 }3 [ 74.590000] [cbm] { cbm_dp_port_alloc : 3426 }4 [ 74.590000] [cbm] { cbm_dp_port_alloc : 3431 }5 [ 74.600000] [cbm] { cbm_dp_port_alloc : 3471 }before port setting 4 [ 74.600000] [cbm] { cbm_add_to_list : 244 }pmac 9 [ 74.610000] [cbm] { cbm_dp_port_alloc : 3545 }port id 9 [ 74.610000] DC DP [dc_dp_alloc_port:272] Success, returned port_id=9. [ 74.620000] [4294944758] mtlk0(mtlk_df_dcdp_datapath_dev_register:11793): Registering network device wlan0 in DirectConnect... [ 74.630000] DC DP [dc_dp_register_dev:300] owner=72f4745c, port_id=8, dev=7afbb000, datapathcb=72f43050, resources=758d0fa4, devspec=758d0e94, flags=0x00001000 [ 74.640000] DC DP [xrx500_dcmode0_register_dev_ex:1320] dev_ctx= (null), owner=72f4745c, port_id=8, dev=7afbb000, datapathcb=72f43050, resources=758d0fa4, dev_spec=758d0e94, flags=0x00001000 [ 74.660000] DC DP [xrx500_setup_umt_port:995] Configuring UMT HW. [ 74.670000] DC DP [xrx500_setup_pmac_port:414] PMAC_EG_CFG_SET for GSW-R. [ 74.670000] DC DP [xrx500_setup_pmac_port:446] PMAC_IG_CFG_SET for GSW-R. [ 74.680000] DC DP [xrx500_setup_pmac_port:521] GSW PMAC Init Done. [ 74.690000] DC DP [xrx500_dcmode0_register_dev_ex:1426] Configuring DMA1-Tx channel 0x1000007. [ 74.700000] DC DP [xrx500_alloc_ring_buffers:554] Allocating 1 DMA1-Tx buffer lists. [ 74.700000] DC DP [xrx500_alloc_ring_buffers:569] allocating pool 1 of size 4096 KB. [ 74.710000] DC DP [xrx500_prepare_channel:634] Preparing channel 2. [ 74.720000] DC DP [xrx500_prepare_channel:696] Prepared channel 2. [ 74.720000] DC DP [xrx500_prepare_channel:634] Preparing channel 4. [ 74.730000] DC DP [xrx500_prepare_channel:696] Prepared channel 4. [ 74.740000] DC DP [dc_dp_register_dev:416] Returned 0. [ 74.740000] [4294944770] mtlk0(mtlk_df_dcdp_datapath_dev_register:11816): Registering network device wlan2 in DirectConnect... [ 74.750000] DC DP [dc_dp_register_dev:300] owner=72f4745c, port_id=9, dev=75b74800, datapathcb=72f43050, resources=758d0fa4, devspec=758d0ebc, flags=0x00001200 [ 74.770000] DC DP [xrx500_dcmode0_register_dev_ex:1320] dev_ctx= (null), owner=72f4745c, port_id=9, dev=75b74800, datapathcb=72f43050, resources=758d0fa4, dev_spec=758d0ebc, flags=0x00001200 [ 74.780000] DC DP [dc_dp_register_dev:416] Returned 0. [ 74.790000] [4294944775] mtlk0(mtlk_df_dcdp_datapath_dev_register:11853): DirectConnect accel type:2, ring type:2 --> GRX350/550 FastPath [ 74.800000] [4294944776] mtlk0(mtlk_df_dcdp_datapath_dev_register:11889): Network device wlan0 registered in DirectConnect [ 74.810000] [4294944777] mtlk0(mtlk_df_dcdp_datapath_dev_register:11891): Network device wlan2 registered in DirectConnect [ 74.830000] [4294944779] mtlk0(_mtlk_mmb_data_path_init:8698): card_idx:0, DP_port_id:8, ep3Msb:4 [ 74.830000] [4294944779] mtlk0(_mtlk_mmb_data_path_init:8717): DCDP: setup HW_MODE0 rings [ 74.840000] [4294944780] mtlk0(_mtlk_mmb_data_path_init:8802): wlan0: Initializing data path (card_idx:0, rtlog max_nof_streams:1, logger_sid:255) [ 74.870000] [4294944783] mtlk0(_mtlk_mmb_send_hw_dep_cfg:4443): XTAL value 0x64, AFE values: 0x00000000, 0x00000000 [ 74.880000] [4294944784] mtlk0(_hw_init_phy_rx_status:7341): PhyRxStatus: max_sid 254, all_sta_sid 511 [ 74.880000] [4294944784] mtlk0(_mtlk_hw_statistics_init:7083): CID-00: Statistics data: size 81976, buffer 0x67440000, dma_addr 0x27440000, buff_copy 0x75b40000 [ 74.900000] [4294944786] mtlk0(mtlk_core_set_net_state:769): wlan0: Going from NET_STATE_HALTED to NET_STATE_IDLE [ 74.930000] [4294944789] mtlk0(_core_cfg_store_country_code:1258): CID-0000: Country Code set to: "US" [ 74.930000] [4294944789] mtlk0(_mtlk_dut_core_irbd_register:698): CID-0000: Register DUT IRBD... [ 74.960000] [4294944792] mtlk0(mtlk_core_set_net_state:769): wlan0: Going from NET_STATE_IDLE to NET_STATE_READY [ 75.000000] [4294944796] mtlk0(_mtlk_df_user_priv_subxface_start:1504): wlan0: Register DirectConnect subinterface (port_id=8, vap_id=0) [ 75.010000] DC DP [dc_dp_register_subif:430] owner=72f4745c, dev=7afbb000, subif_id=7afd7368, flags=0x00000000 [ 75.020000] DC DP [xrx500_dcmode0_register_subif:1485] dev_ctx=7c7bd018, owner=72f4745c, dev=7afbb000, subif_id=7afd7368, flags=0x00000000 [ 75.030000] DC DP [xrx500_dcmode0_register_subif:1584] Enabling UMT HW. [ 75.040000] [cbm] { cbm_dp_enable : 3853 }******************ep=8 tmu_port=4 queue=32 sid=16 [ 75.050000] [cbm] { cbm_dp_enable : 3884 }enable queue 32 [ 75.050000] [cbm] { cbm_dp_enable : 3885 }flag 1 refcnt 1024 [ 75.060000] DC DP [xrx500_dcmode0_register_subif:1647] Returned 0. [ 75.060000] DC DP [dc_dp_register_subif:525] Success, returned 0. [ 75.070000] [4294944803] mtlk0(_mtlk_df_user_priv_subxface_start:1521): wlan0: DirectConnect subinterface is registered (port_id=8, vap_id=0) [ 75.080000] [4294944804] mtlk0(mtlk_df_user_group_init:10823): wlan0: multicast callback registered [ 75.090000] [4294944805] mtlk0(mtlk_core_set_net_state:769): wlan2: Going from NET_STATE_HALTED to NET_STATE_IDLE [ 75.120000] [4294944808] mtlk0(_core_cfg_store_country_code:1258): CID-0100: Country Code set to: "US" [ 75.120000] [4294944808] mtlk0(_mtlk_dut_core_irbd_register:698): CID-0100: Register DUT IRBD... [ 75.150000] [4294944811] mtlk0(mtlk_core_set_net_state:769): wlan2: Going from NET_STATE_IDLE to NET_STATE_READY [ 75.160000] [4294944812] mtlk0(_mtlk_df_user_priv_subxface_start:1504): wlan2: Register DirectConnect subinterface (port_id=9, vap_id=0) [ 75.170000] DC DP [dc_dp_register_subif:430] owner=72f4745c, dev=75b74800, subif_id=75b7f368, flags=0x00000000 [ 75.180000] DC DP [xrx500_dcmode0_register_subif:1485] dev_ctx=7c7bd32c, owner=72f4745c, dev=75b74800, subif_id=75b7f368, flags=0x00000000 [ 75.190000] DC DP [xrx500_dcmode0_register_subif:1647] Returned 0. [ 75.200000] DC DP [dc_dp_register_subif:525] Success, returned 0. [ 75.200000] [4294944816] mtlk0(_mtlk_df_user_priv_subxface_start:1521): wlan2: DirectConnect subinterface is registered (port_id=9, vap_id=0) [ 75.220000] [4294944818] mtlk0(mtlk_df_user_group_init:10823): wlan2: multicast callback registered [ 75.230000] [4294944819] mtlk0(wave_radio_calibrate:5448): Processing RadioID 0 [ 75.230000] [4294944819] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ProgModel_gen6_Common.bin') is starting pu_telnetEnabled log level is 0(LOG_ERROR). [ 75.280000] [4294944824] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ProgModel_gen6_Ant_Tx.bin') is starting [ 75.300000] [4294944826] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ProgModel_gen6_Ant_Rx.bin') is starting [ 75.330000] [4294944829] mtlk0(prepare_progmodel_string:4054): CID-0000: ProgModel: ProgModel_gen6_Common.bin version 1909051004 [ 75.330000] [ 75.350000] [4294944831] mtlk0(mtlk_hw_send_cal_rfic_data:13118): RFIC calibration data missing [ 75.370000] [4294944833] mtlk0(_wave_radio_hdk_config_send:4942): band=1, offline_algo_mask=0xffffffff, online_algo_mask=0xffffffff [ 75.380000] [4294944834] mtlkE(_wave_radio_hdk_config_send:4968): dump of HDK_CONFIG_REQ [ 75.390000] [4294944835] mtlkE(_wave_radio_hdk_config_send:4968): cp= 0x72f90564 l=24 [ 75.400000] [4294944836] mtlkE(_wave_radio_hdk_config_send:4968): 0000: 00 00 XX XX 00 00 00 00 XX XX 00 06 00 00 01 00 [ 75.410000] [4294944837] mtlkE(_wave_radio_hdk_config_send:4968): 0010: ff ff ff ff ff ff ff ff [ 75.440000] [4294944840] mtlk0(wave_radio_calibrate:5461): Pre-calibration for RadioID 0 succeeded [ 75.450000] [4294944841] mtlk0(wave_radio_calibrate:5448): Processing RadioID 1 [ 75.460000] [4294944842] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ProgModel_gen6_Common.bin') is starting [ 75.470000] [4294944843] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ProgModel_gen6_Ant_Tx.bin') is starting [ 75.490000] [4294944845] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('ProgModel_gen6_Ant_Rx.bin') is starting [ 75.520000] [4294944848] mtlk0(prepare_progmodel_string:4054): CID-0000: ProgModel: ProgModel_gen6_Common.bin version 1909051004 [ 75.520000] [ 75.540000] [4294944850] mtlk0(mtlk_hw_send_cal_rfic_data:13118): RFIC calibration data missing [ 75.540000] [4294944850] mtlk0(_wave_radio_hdk_config_send:4942): band=0, offline_algo_mask=0xffffffff, online_algo_mask=0xffffffff [ 75.550000] [4294944851] mtlkE(_wave_radio_hdk_config_send:4968): dump of HDK_CONFIG_REQ [ 75.560000] [4294944852] mtlkE(_wave_radio_hdk_config_send:4968): cp= 0x72f902cc l=24 [ 75.570000] [4294944853] mtlkE(_wave_radio_hdk_config_send:4968): 0000: 00 00 XX XX 00 00 00 00 02 XX 00 XX 00 00 00 00 [ 75.580000] [4294944854] mtlkE(_wave_radio_hdk_config_send:4968): 0010: ff ff ff ff ff ff ff ff [ 75.600000] [4294944856] mtlk0(wave_radio_calibrate:5461): Pre-calibration for RadioID 1 succeeded [ 75.610000] [4294944857] mtlk0(_wave_radio_dummy_vap_add:5098): Mac addr for calibration VAP is XX:XX:XX:XX:XX:XX [ 75.670000] [4294944863] mtlk0(_wave_radio_2G_calibrate:5305): 20Mhz channels [ 76.400000] [4294944936] mtlk0(_wave_radio_2G_calibrate:5321): 40Mhz channels [ 76.880000] [4294944984] mtlk0(_wave_radio_dummy_vap_del:5159): VAP is removed (status 0), result 0 [ 76.890000] [4294944985] mtlk0(wave_radio_calibrate:5480): Calibration for RadioID 0 succeeded [ 76.900000] [4294944986] mtlk0(_wave_radio_dummy_vap_add:5098): Mac addr for calibration VAP is XX:XX:XX:XX:XX:XX [ 76.910000] [4294944987] mtlk0(_wave_radio_5G_calibrate:5344): 20Mhz channels [ 78.110000] [4294945107] mtlk0(_wave_radio_5G_calibrate:5360): 40Mhz channels [ 78.690000] [4294945165] mtlk0(_wave_radio_5G_calibrate:5376): 80Mhz channels [ 78.990000] [4294945195] mtlk0(_wave_radio_5G_calibrate:5392): 160Mhz channels [ 79.090000] [4294945205] mtlk0(_wave_radio_dummy_vap_del:5159): VAP is removed (status 0), result 0 [ 79.100000] [4294945206] mtlk0(wave_radio_calibrate:5480): Calibration for RadioID 1 succeeded [ 79.110000] [4294945207] mtlk0(wv_ieee80211_setup_register:2191): Registering mac80211 HW [ 79.120000] [4294945208] mtlk0(wv_cfg80211_init_band:2163): 2.4 GHz band supported, up to 2 spatial streams [ 79.150000] [4294945211] mtlk0(_core_cfg_store_country_code:1258): CID-0000: Country Code set to: "00" [ 79.210000] [4294945217] mtlk0(wv_ieee80211_setup_register:2191): Registering mac80211 HW [ 79.220000] [4294945218] mtlk0(wv_cfg80211_init_band:2163): 5 GHz band supported, up to 2 spatial streams [ 79.290000] [4294945225] mtlk0(_core_cfg_store_country_code:1258): CID-0100: Country Code set to: "00" [ 79.390000] [4294945235] mtlk0(mtlk_fast_mem_print_info:115): Using normal memory for hot context [ 79.400000] PCI: Enabling device 0000:03:00.0 (0000 -> 0002) [ 79.400000] [4294945236] mtlk0(_pci_mem_get:611): PCI Memory block 0: PA: 0xb4000000, VA: 0xf4000000, Len=0x2000000 [ 79.410000] [MTLKD] PCIE bus ChipVersion:UNKNOWN ChipID is:0x0000 address is:0xf4220060 [ 79.420000] [MTLKD] PCI AUX Initialization finished head: cat: No such file or directory ==> /proc/net/mtlk/version <== Driver version: 6.1.0_bp.0.27.bfbd5bc5bc82a779ff78e1a2dea9f2b4bc78aa4d.PcieG5.PcieG6.Release MAC/PHY versions: ap_ram_gen6_wrx_600_real_phy.bin: @@@ VERSION INFO @@@ version number: 20200319_144033_carterch_#_14 Upper CPU WAVE600 phy type: real phy on Mar 19 2020 at 14:41:27@@@ END @@@ tx_sender_gen6.bin: base release 25616, curr.release 0 host_interface_gen6_dc_mode0.bin: base release 57102, curr.release 0 rx_handler_gen6.bin: base release 58193, curr.release 0 ProgModel: ProgModel_gen6_Common.bin version 1909051004 [ 79.630000] [4294945259] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('cal_wlan0.bin') is starting [ 79.660000] [4294945262] mtlk0(_mtlk_df_fw_request_firmware:43): Request Firmware ('cal_wlan0.bin') is starting FAPIWAVESCRIPTS FAPI_DAEMON FAPI_DAEMON /opt/lantiq/wave/scripts/fapi_wlan_wave_daemon_start: Start FAPI daemon <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2038}: CSD took more time than expected <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.Interface.1. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.RMONStats.1. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.Interface.2. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.RMONStats.2. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.Interface.3. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.RMONStats.3. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.Interface.4. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.RMONStats.4. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.Interface.5. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.RMONStats.5. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.X_LANTIQ_COM_NwHardware.LANGroup.1. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.Link.33. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.IP.Interface.33. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Routing.Router.1.IPv4Forwarding.19. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.X_LANTIQ_COM_NwHardware.LANGroup.2. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.Link.34. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.IP.Interface.34. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Routing.Router.1.IPv4Forwarding.20. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.X_LANTIQ_COM_NwHardware.LANGroup.3. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.Link.35. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.IP.Interface.35. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Routing.Router.1.IPv4Forwarding.21. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.X_LANTIQ_COM_NwHardware.LANGroup.4. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Ethernet.Link.36. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.IP.Interface.36. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.Routing.Router.1.IPv4Forwarding.22. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.IP.Interface.1. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.IP.Interface.2. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.X_LANTIQ_COM_NwHardware.WANGroup.1. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2041}: SET obj=Device.IP.Interface.32. owner=4 obj_oper=4 <01-01-1970 09:01:24> [CRITICAL] CSD {ubus_cfgapiSet, 2043}: CSD SET operation completed in 27.957000 seconds with ret=0 <01-01-1970 09:01:24> [CRITICAL] CAPI {capi_setValue, 354}: CAPI SET completed in 27.982000 seconds with ret=0 <01-01-1970 09:01:24> [CRITICAL] libcal {cal_setValue, 350}: CAL_SET completed for Device.Ethernet.Interface. in 27.983000 seconds with ret=0 <01-01-1970 09:01:24> [CRITICAL] SERVD {servd_startSlLibsInit, 327}: SL init of SL Library 'sl_eth' completed in 33.654000 seconds <01-01-1970 09:01:24> [CRITICAL] libcal {cal_getValue, 168}: CAL_GET completed for Device.Users.User in 8.600000 seconds with ret=0 [ 84.560000] [pecoevent_collect] { kpeco_init : 437 }pecostat event installed.. with major device number 350 ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_radio_set: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_radio_set: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_ssid_add: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_ssid_set: init flow with conf from previous setting - FAST BOOT CMD: uci get dhcp.@dnsmasq[0] ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_endpoint_set: init flow with conf from previous setting - FAST BOOT cfg02411c CMD: uci get dhcp.@host[0].ip CMD: uci get dhcp.@host[0].mac cfg05fe63 ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_ssid_add: init flow with conf from previous setting - FAST BOOT /etc/rc.common: eval: line 591: can't create /tmp/hosts/dhcp: nonexistent directory ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_ssid_set: init flow with conf from previous setting - FAST BOOT udhcpc: started, v1.30.1 udhcpc: sending discover ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_endpoint_set: init flow with conf from previous setting - FAST BOOT [ 87.110000] jnl: driver (UFSD_HEAD lke_9.6.9_b440) loaded at 75b60000 [ 87.470000] ufsd: module license 'Commercial product' taints kernel. [ 87.480000] Disabling lock debugging due to kernel taint [ 87.530000] ufsd: driver (UFSD_HEAD lke_9.6.9_b440, paragon, acl, ioctl, sd2(5), tr, car) loaded at 75b80000 [ 87.530000] NTFSJ support included [ 87.530000] Big endian platform [ 87.530000] Build_for__Netgear_AX3000_k3.10.104_2017-09-13_lke_9.6.9_b440 [ 87.550000] ufsd: PAGE_SIZE=4K, THREAD_SIZE=8k [ 87.560000] ufsd: Kernel .config hash: original 0xc3658694, current 0x30a2edc6, not matched. [ 87.570000] ufsd: Kernel .config hash: original 0xc3658694, current 0x30a2edc6, not matched ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_up: init flow with conf from previous setting - FAST BOOT [ 88.340000] device rtlog0 entered promiscuous mode [ 88.350000] br-lan: port 5(rtlog0) entered forwarding state [ 88.350000] br-lan: port 5(rtlog0) entered forwarding state [ 88.360000] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 88.480000] [4294946144] mtlk0(mtlk_log_set_conf:911): Using value of 0 for all console debug levels, OID 8 [ 88.680000] [MTLKD] Switch off FW wlan 0 Stream 0 [ 88.680000] [MTLKD] mtlk_rtlog_set_iph_check: Change iph->check from 0000 to AF43 [ 88.690000] [MTLKD] Switch On FW wlan 0 Stream 0 [ 88.690000] [MTLKD] swPreCalcChecksum 0x50bc (0x50bc in network endian) [ 88.700000] [4294946166] mtlk0(_mtlk_mmb_rtlog_fw_add_stream:8266): wlan_if 0, FwAddStream 0 request [ 88.720000] [MTLKD] Switch off Driver Stream ln: /tmp/debug_level: File exists 2020-09-20 11:45:11: (server.c.2118) server stopped by UID = 0 PID = 3358 /tmp/lighttpd4.conf exist. lighttpd-angel.c.148: child (pid=3374) exited normally with exitcode: 0 fapi_wlan_up; Inside object 'Device.WiFi.Radio' the field 'Status' is NULL (ifname= 'wlan1') ==> check 'Device.WiFi.SSID' field 'Status' fapi_wlan_up; ifname= 'wlan1', Object= 'Device.WiFi.SSID', Status= 'Down' udhcpc: no lease, failing ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_up: init flow with conf from previous setting - FAST BOOT ioctl: No such device [ 90.740000] [4294946370] mtlk0(mtlk_log_set_conf:911): Using value of 0 for all console debug levels, OID 8 [ 90.890000] [MTLKD] Switch off FW wlan 2 Stream 0 [ 90.900000] [MTLKD] mtlk_rtlog_set_iph_check: Change iph->check from 0000 to AF43 [ 90.910000] [MTLKD] Switch On FW wlan 2 Stream 0 [ 90.910000] [MTLKD] swPreCalcChecksum 0x50bc (0x50bc in network endian) [ 90.920000] [MTLKD] WARN: wlan_if 2: clb is not set [ 90.920000] [MTLKD] Switch off Driver Stream fapi_wlan_up; Inside object 'Device.WiFi.Radio' the field 'Status' is NULL (ifname= 'wlan3') ==> check 'Device.WiFi.SSID' field 'Status' fapi_wlan_up; ifname= 'wlan3', Object= 'Device.WiFi.SSID', Status= 'Down' ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_ssid_add: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_ssid_set: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_ap_set: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_hotspot_set: init flow with conf from previous setting - FAST BOOT ####### fapi_wlan_wave_security_set: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_wps_set: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_wmm_ap_set: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_ssid_add: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_ssid_set: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_ap_set: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_hotspot_set: init flow with conf from previous setting - FAST BOOT ####### fapi_wlan_wave_security_set: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_wps_set: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_wmm_ap_set: init flow with conf from previous setting - FAST BOOT ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_up: init flow with conf from previous setting - FAST BOOT cat: can't open '/tmp/wlan_wave/drv_config_post_up_wlan0.*.conf': No such file or directory /opt/lantiq/wave/scripts/fapi_wlan_wave_up: Start hostapd_wlan0 Configuration file: /opt/lantiq/wave/confs/hostapd_wlan0.conf rfkill: Cannot op[ 97.040000] [4294947000] mtlk0(_mtlk_df_user_iface_open:1711): wlan0: start the interface en RFKILL control device [ 97.050000] device wlan0 entered promiscuous mode [ 97.060000] br-lan: port 6(wlan0) entered forwarding state [ 97.060000] br-lan: port 6(wlan0) entered forwarding state nl80211: sending SET[ 97.070000] [4294947003] mtlk0(_core_cfg_store_country_code:1258): CID-0100: Country Code set to: "JP" [ 97.080000] [4294947004] mtlk0(_core_cfg_store_country_code:1258): CID-0000: Country Code set to: "JP" _[ 97.090000] [4294947005] mtlk0(_core_cfg_store_country_code:1258): CID-0000: Country Code set to: "JP" NON_TRANSMIT_VAP: 0 nl80211: sending SET_MBSSID_NUM_VAPS_IN_GROUP: 0 wlan0: interface state UNINITIALIZED->COUNTRY_UPDATE int[ 97.110000] [4294947007] mtlk0(_scan_do_scan:1369): wlan0: Beginning scan, requester_vap_index=0 erface ID: 0 [ 97.130000] [4294947009] mtlk0(mtlk_core_set_net_state:769): wlan0: Going from NET_STATE_READY to NET_STATE_ACTIVATING [ 97.140000] [4294947010] mtlk0(mtlk_mbss_send_vap_activate:2447): CID-0000: UMI_ADD_VAP, BSSID 78:D2:94:E7:FC:F8 [ 97.150000] [4294947011] mtlk0(_scan_do_scan:1412): radio mode 0 [ 97.160000] [4294947012] mtlk0(_mtlk_core_set_radio_mode_req:5230): CID-0000:EnableRadio FW request: Set 1 mode [ 97.170000] [4294947013] mtlk0(_scan_do_scan:1441): Scan by ap - orig_certain=0, has_stas_connected=0, do_background_scan=0 /opt/lantiq/wave/scripts/fapi_wlan_wave_up: wlan0; Start fapi_wlan_daemon (hostapd) listener fdHostapdSet; Supported Interface 'wlan0' Waiting for hostapd radio interface to be ready. Waiting for wlan0 to be readyfdHostapdSet; radio interface 'wlan1' not present ==> Continue Waiting ...hostapd state=ACS [ 98.540000] [4294947150] mtlk0(clean_up_after_this_scan:740): wlan0: Leaving the channel as uncertain after the scan [ 98.550000] [4294947151] mtlk0(scan_timeout_func:1213): wlan0: Scan done: res=0 /opt/lantiq/wave/confs/fapi_wlan_wave_runner.sh:start wait for recovery event on drvhlpr wlan0 [ 98.590000] [4294947155] mtlkE(mtlk_mmb_bss_mgmt_tx:12273): VAP not yet activated, net_state=0x8 [ 98.910000] [4294947187] mtlk0(core_cfg_set_chan_clpb:782): Notifying the kernel about the channel switch (width 20, primary at 1) [ 98.920000] [4294947188] mtlk0(_mtlk_core_activate:3602): CID-0000: open interface [ 98.930000] [4294947189] mtlk0(mtlk_core_set_net_state:769): wlan0: Going from NET_STATE_ACTIVATING to NET_STATE_CONNECTED [ 98.950000] [4294947191] mtlkE(mtlk_coc_set_antenna_params:689): CID-0000: Wrong CoC power mode TX4xRX4 [ 98.970000] [4294947193] mtlk0(_mtlk_core_set_interfdet_do_params:7324): CID-0000: Interference detection is activated Waiting ...hostapd state=ENABLED killall: proftpd: no process killed <20-09-2020 11:45:22> [CRITICAL] SERVD {servd_startSlLibsInit, 327}: SL init of SL Library 'sl_usb_hosts' completed in 12.672000 seconds /opt/lantiq/wave/confs /opt/lantiq/wave/hostapd_debug procd: respawn Instance devmd::instance1 crashed with error code 32512 after 1 seconds!! 2020-09-20 11:45:22: (network.c.294) warning: server.set-v6only will be removed soon, update your config to have different sockets for ipv4 and ipv6 2020-09-20 11:45:22: (server.c.1525) server started (lighttpd/1.4.47) [ 100.120000] [4294947308] mtlk0(_mtlk_core_set_interfdet_do_params:7324): CID-0000: Interference detection is activated [ 100.160000] [4294947312] mtlk0(_mtlk_core_send_fixed_ltf_and_gi:4679): CID-0000: Fixed LTF and GI - isAuto:(1) ltfAndGi:(0) [ 100.180000] [MTLKD] MuStaticPlan is Off [ 100.180000] [MTLKD] Apply numOfParticipatingStations=0 due to plan is Off [ 100.190000] [4294947315] mtlk0(_mtlk_core_send_static_plan_config:1949): CID-0000: StaticPlanConfig uci: Entry not found uci: Entry not found fapi_wlan_up; ifname= 'wlan0', Object= 'Device.WiFi.Radio', Status= 'Up' fapi_wlan_post_up; FAPI connect to hostapd/supplicant interface (ifname= 'wlan0') cp: can't stat 'cp': No such file or directory ########################################### Command failed: Not found [main 381 ] @@@@@ UBUS MSG : service delete { "name": "odhcpd" } ########################################### module is already loaded - usbnet [ 101.610000] usbcore: registered new interface driver cdc_ether module is already loaded - cdc_ncm module is already loaded - cdc-acm module is already loaded - cdc-wdm ####### /opt/lantiq/wave/scripts/fapi_wlan_wave_up: init flow with conf from previous setting - FAST BOOT cat: can't open '/tmp/wlan_wave/drv_config_post_up_wlan2.*.conf': No such file or directory /opt/lantiq/wave/scripts/fapi_wlan_wave_up: Start hostapd_wlan2 Configuration file: /opt/lantiq/wave/confs/hostapd_wlan2.conf rfkill: Cannot op[ 102.790000] [4294947575] mtlk0(_mtlk_df_user_iface_open:1711): wlan2: start the interface en RFKILL control device [ 102.810000] device wlan2 entered promiscuous mode [ 102.810000] br-lan: port 7(wlan2) entered forwarding state [ 102.810000] br-lan: port 7(wlan2) entered forwarding state nl80211: sending SET[ 102.820000] [4294947578] mtlk0(_core_cfg_store_country_code:1258): CID-0100: Country Code set to: "JP" _NON_TRANSMIT_VAP: 0 nl80211: sending SET_MBSS[ 102.840000] [4294947580] mtlk0(_scan_do_scan:1369): wlan2: Beginning scan, requester_vap_index=0 [ 102.850000] [4294947581] mtlk0(mtlk_core_set_net_state:769): wlan2: Going from NET_STATE_READY to NET_STATE_ACTIVATING [ 102.860000] [4294947582] mtlk0(mtlk_mbss_send_vap_activate:2447): CID-0100: UMI_ADD_VAP, BSSID 78:D2:94:E7:FC:FA ID_NUM_VAPS_IN_GROUP: 0 wlan2: [ 102.870000] [4294947583] mtlk0(_scan_do_scan:1412): radio mode 0 [ 102.870000] [4294947583] mtlk0(_mtlk_core_set_radio_mode_req:5230): CID-0100:EnableRadio FW request: Set 1 mode [ 102.880000] [4294947584] mtlk0(_scan_do_scan:1441): Scan by ap - orig_certain=0, has_stas_connected=0, do_background_scan=0 interface state UNINITIALIZED->COUNTRY_UPDATE wlan2: interface state COUNTRY_UPDATE->HT_SCAN interface ID: 1 [ 103.100000] [4294947606] mtlk0(clean_up_after_this_scan:740): wlan2: Leaving the channel as uncertain after the scan [ 103.110000] [4294947607] mtlk0(scan_timeout_func:1213): wlan2: Scan done: res=0 [ 103.130000] br-lan: port 7(wlan2) entered disabled state [ 103.140000] [4294947610] mtlk0(core_cfg_set_chan:858): Setting the CAC timer for 60000 ms cat: can't open '/etc/needhash': No such file or directory [ 103.360000] br-lan: port 5(rtlog0) entered forwarding state w`T: line 1: /bin/smbpasswd: not found /opt/lantiq/wave/scripts/fapi_wlan_wave_up: wlan2; Start fapi_wlan_daemon (hostapd) listener fdHostapdSet; radio interface 'wlan1' not present ==> Continue Waiting for hostapd radio interface to be ready. Waiting ...hostapd state=DFS /opt/lantiq/wave/confs/fapi_wlan_wave_runner.sh:start wait for recovery event on drvhlpr wlan2 sed: /tmp/lighttpd2.conf: No such file or directory /bin/sh: ./S11lighttpd2: not found ln: /tmp/debug_level: File exists 2020-09-20 11:45:27: (server.c.2118) server stopped by UID = 0 PID = 1 killall: pu_telnetEnabled: no process killed pu_telnetEnabled log level is 0(LOG_ERROR). procd: respawn Instance devmd::instance1 crashed with error code 32512 after 0 seconds!! netlink recv: No buffer space available procd: respawn Instance devmd::instance1 crashed with error code 32512 after 0 seconds!! <20-09-2020 11:45:34> [CRITICAL] SERVD {servd_startSlLibsInit, 327}: SL init of SL Library 'sl_qos' completed in 6.170000 seconds module is already loaded - mcast_helper [ 111.850000] L2NAT:l2nat_init:859 l2nat module loaded [ 112.080000] br-lan: port 6(wlan0) entered forwarding state procd: respawn Instance devmd::instance1 crashed with error code 32512 after 0 seconds!! procd: respawn Instance devmd::instance1 crashed with error code 32512 after 0 seconds!! [ 163.360000] [4294953632] mtlk0(cac_timer_serialized_func:276): CAC timer expired [ 163.370000] [4294953633] mtlkE(mtlk_mmb_bss_mgmt_tx:12273): VAP not yet activated, net_state=0x8 [ 164.020000] [4294953698] mtlk0(_mtlk_core_activate:3602): CID-0100: open interface [ 164.030000] [4294953699] mtlk0(mtlk_core_set_net_state:769): wlan2: Going from NET_STATE_ACTIVATING to NET_STATE_CONNECTED [ 164.040000] br-lan: port 7(wlan2) entered forwarding state [ 164.040000] br-lan: port 7(wlan2) entered forwarding state [ 164.050000] [4294953701] mtlkE(mtlk_coc_set_antenna_params:689): CID-0100: Wrong CoC power mode TX4xRX4 [ 164.070000] [4294953703] mtlk0(_mtlk_core_set_interfdet_do_params:7324): CID-0100: Interference detection is activated Waiting ...hostapd state=ENABLED /opt/lantiq/wave/confs /opt/lantiq/wave/hostapd_debug [ 164.300000] [4294953726] mtlk0(_mtlk_core_set_interfdet_do_params:7324): CID-0100: Interference detection is activated [ 164.340000] [4294953730] mtlk0(_mtlk_core_send_fixed_ltf_and_gi:4679): CID-0100: Fixed LTF and GI - isAuto:(1) ltfAndGi:(0) [ 164.360000] [MTLKD] MuStaticPlan is Off [ 164.360000] [MTLKD] Apply numOfParticipatingStations=0 due to plan is Off [ 164.370000] [4294953733] mtlk0(_mtlk_core_send_static_plan_config:1949): CID-0100: StaticPlanConfig [ 164.400000] [4294953736] mtlkW(_mtlk_core_async_clb:433): CID-0100: Requested ability 0x10000D3 is disabled or never was registered command failed: Device or resource busy (-16) fapi_wlan_up; ifname= 'wlan2', Object= 'Device.WiFi.Radio', Status= 'Up' fapi_wlan_post_up; FAPI connect to hostapd/supplicant interface (ifname= 'wlan2') fdHostapdSet; Supported Interface 'wlan2' <20-09-2020 11:46:33> [CRITICAL] SERVD {servd_startSlLibsInit, 327}: SL init of SL Library 'sl_wlan' completed in 121.655000 seconds ###NOTIFY_ALL_INIT_COMPLETED#### stop ntgrselfled thread... sh: write error: Bad address BOOTLoader: U-Boot-2010.06-LANTIQ-v-2.3.149-R11 mem=480M@512M CPU: EASY350 ANYWAN (GRX350) Router model CPU Clock: 800.000 Kernel: 3.10.108 Software: UGW-7.5.2.50-1148-22May20 Toolchain: 4.8-linaro/0.9.33.2 PPA SubSystem version info: v3.4.2-0 PPA ppacmd utility tool info: 2.9.0 PPA API driver info: 96.32.7.3.0.0.4 PPA Stack Adaption Layer driver info: 96.16.0.0.0.0.3 PAE HAL driver info: 16.4.2.17.0.0.2 MPE HAL driver info: 0.0.0.0.0.0.0 MPE FW version: 1.1.1.1.1 Switch API Version: 3.0.2 Wave wlan version: 06.01.00_ER5.49 Wave wlan driver version: Wave wlan MAC FW version: FW_6.1.0_ER5_20200115_123958 Wave wlan tx_sender version: genrisc_tx_sender_6.1.0_er5_20200108_141323 Wave wlan rx_handler version: genrisc_rx_handler_6.1.0_20190704_230345 Wave wlan host_interface version: genrisc_host_interface_6.1.0_20190704_230501 Wave wlan Wave500B PROGMODEL version: 4201 Wave wlan Wave600 PROGMODEL version: 1909051004 Wave wlan PSD version: 2019-06-19_13-32-03_REV_0af2095db18c pm_util version: 2.0.1 ppmd version: 1.2.3 spdmon version: 1.4.0 ltq_pmcu version: 1.3.6 CoC: ltq_cpufreq_drv 3.0.0 RAX40 FW version:V1.0.3.80_1.0.1 RAX40 HW version:R1.05 RAX40 SKU Name:JP RAX40 FW DB version:V3.28 RAX40 RAE version:V1.0.0.26 grep: invalid option -- 1 ifconfig: up: error fetching interface information: Device not found <20-09-2020 11:46:39> [CRITICAL] libcal {cal_getValue, 168}: CAL_GET completed for Device.Time in 125.341000 seconds with ret=0 uci: Entry not found ioctl: No such device ###NOTIFY_BRIDGE_UP#### ############################################# ################# BOOT OK ################ #############################################


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2023/01/09 19:09
  • by danitool