User Tools

Site Tools


inbox:toh:netgear:netgear_r6020

Netgear R6020

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

The Netgear R6020 is a dual band WiFi router. The router has 2 non-detachable antennas and a 10/100 FastEthernet switch.

Generic Router

Supported Versions

Hardware Highlights

ModelVersionSoCCPU MHzFlash MBRAM MBWLAN HardwareWLAN2.4WLAN5.0100M portsGbit portsModemUSB
R6020MediaTek MT7628A580864MediaTek MT7628A, MediaTek MT7612Eb/g/na/n/ac5---

Installation

Debricking

Hardware

Info

Architecture MT7628
Vendor Ralink
Bootloader U-Boot 1.1.3
System-On-Chip Ralink MT7628 - MIPS 24Kc V5.5
CPU/Speed 580 MHz
Flash-Chip mx25l6406e
Flash size 8 MiB
RAM 64 MiB
Wireless MIPS 24Kc V5.5
Ethernet 10/100 Mbit/s
USB Unpopulated/Untested
Serial Yes
JTAG ?

Photos

Insert photo of front of the casing

Insert photo of back of the casing

Insert photo of backside label

Insert photo of PCB

Opening the case

Two T8 security screws on the bottom, then pry the top case out to release the six catches (2 on front, 2 on left, 2 on right).

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

JP1 on right side of board:

Rx VCC Tx GND
Serial connection parameters
for Netgear R6020
57600, 8N1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootlogs

OEM bootlog

[04000C0E][04000D09] DDR Calibration DQS reg = 00008887 U-Boot 1.1.3 (Oct 31 2017 - 12:57:49) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83f70000 flash manufacture id: c2, device id 20 17 find flash: MX25L6405D *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC 7628_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Oct 31 2017 Time:12:57:49 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes RESET MT7628 PHY!!!!!! Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. default: 3 You choosed 3 0 *************************************************** Sercomm Boot Version 4.1.1.0 *************************************************** Entering Firmware : Everything is OK. Enter NMRP_main 0x0000:8c 3b ad ea 7b 3b Trying Eth0 (10/100-M) Waitting for RX_DMA_BUSY status Start... done ETH_STATE_ACTIVE!! NMRP_FLASH_SIZE_buffer --> 82000000. NMRP:LISTENING ### No NMRP Server found ### TFTP Recovery Flag is 0xff 3: System Boot system code via Flash. ## Booting image at bc090000 ... Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1606607 Bytes = 1.5 MB Load Address: 80000000 Entry Point: 8000c150 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000c150) ... ## Giving linux memsize in MB, 64 Starting kernel ... LINUX started... THIS IS ASIC SDK 5.0.S.0 Linux version 2.6.36 (mike@localhost.localdomain) (gcc version 4.6.3 (Buildroot 2012.11.1) ) #1 Thu Dec 21 19:48:54 CST 2017 The CPU feqenuce set to 580 MHz MIPS CPU sleep mode enabled. CPU revision is: 00019655 (MIPS 24Kc) Software DMA cache coherency Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Zone PFN ranges: Normal 0x00000000 -> 0x00004000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00004000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock6 rootfstype=squashfs console=ttyS0 PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Writing ErrCtl register=0007ef0b Readback ErrCtl register=0007ef0b Memory: 59968k/65536k available (3551k kernel code, 5516k reserved, 990k data, 160k init, 0k highmem) NR_IRQS:128 console [ttyS1] enabled Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 NET: Registered protocol family 16 RALINK_GPIOMODE = 570544c4 RALINK_GPIOMODE = 570444c4 ***** Xtal 40MHz ***** start PCIe register access RALINK_RSTCTRL = 2400000 RALINK_CLKCFG1 = fdbfffc0 *************** MT7628 PCIe RC mode ************* PCIE0 enabled Port 0 N_FTS = 1b105000 init_rt2880pci done bio: create slab <bio-0> at 0 pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit] pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff 64bit] (PCI address [0x20000000-0x200fffff] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref] pci 0000:00:00.0: PCI bridge to [bus 01-01] pci 0000:00:00.0: bridge window [io disabled] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref] BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 20200000 res[1]->end = 2020ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0 res[0]->start = 20000000 res[0]->end = 200fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource Ralink Systick timer NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 117 Block layer SCSI generic (bsg) driver version 0.4 loaded (major 254) io scheduler noop registered (default) Ralink gpio driver initialized Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x10000d00 (irq = 21) is a 16550A serial8250: ttyS1 at MMIO 0x10000c00 (irq = 20) is a 16550A brd: module loaded flash manufacture id: c2, device id 20 17 MX25L6405D(c2 2017c220) (8192 Kbytes) mtd .name = raspi, .size = 0x00800000 (8M) .erasesize = 0x00010000 (64K) .numeraseregions = 0 Creating 12 MTD partitions on "raspi": 0x000000000000-0x000000040000 : "Bootloader" 0x000000040000-0x000000060000 : "Factory" 0x000000060000-0x000000070000 : "Ralink Nvram" 0x000000070000-0x000000080000 : "SC_Factory" 0x000000080000-0x000000090000 : "SC_NVRAM" 0x000000090000-0x000000220000 : "Kernel" 0x000000220000-0x000000780000 : "RootFS" 0x000000780000-0x0000007a0000 : "ML" 0x0000007a0000-0x0000007c0000 : "ML1" 0x0000007c0000-0x0000007e0000 : "ML2" 0x0000007e0000-0x0000007f0000 : "POT" 0x0000007f0000-0x000000800000 : "Reserved" rdm_major = 253 GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43e17629 Ralink APSoC Ethernet Driver Initilization. v3.1 512 rx/tx descriptors allocated, mtu = 1500! GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43e17629 PROC INIT OK! PPP generic driver version 2.4.2 PPP MPPE Compression module registered NET: Registered protocol family 24 PPTP driver version 0.8.5 IMQ driver loaded successfully. Hooking IMQ before NAT on PREROUTING. Hooking IMQ after NAT on POSTROUTING. === pAd = c0045000, size = 1023504 === <-- RTMPAllocTxRxRingMemory, Status=0, ErrorValue=0x <-- RTMPAllocAdapterBlock, Status=0 RtmpChipOpsHook(492): Not support for HIF_MT yet! mt7628_init()--> mt7628_init(FW(8a00), HW(8a01), CHIPID(7628)) e2.bin mt7628_init(1135)::(2), pChipCap->fw_len(63888) mt_bcn_buf_init(218): Not support for HIF_MT yet! <--mt7628_init() Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (937 buckets, 3748 max) nf_conntrack_rtsp v0.6.21 loading IPVS: Registered protocols () IPVS: Connection hash table configured (size=4096, memory=32Kbytes) IPVS: ipvs loaded. GRE over IPv4 demultiplexor driver gre: can't add protocol nf_nat_rtsp v0.6.21 loading ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Cone TCP cubic registered NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 L2TP IP encapsulation support (L2TPv3) L2TP netlink interface L2TP ethernet pseudowire support (L2TPv3) 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:6. Freeing unused kernel memory: 160k freed andelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfsinit started: BusyBox v1.12.1 (2017-12-21 19:51:32 CST) filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs^Minit started: BusyBox v1.12.1 (2017-12-21 19:51:32 CST)^M^J filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs^Minit started: BusyBostarting pid 41, tty '': '/usr/etc/rcS' x v1.12.1 (2017-12-21 19:51:32 CST)^M^J filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs^Minit started: BusyBo^Mstarting pid 41, tty '': '/usr/etc/rcS'^M^Jx v1.12.1 (2017-12-21 19:51:32 CST)^M^J filesystem1:6.^M^JFreeing unused kernel memory:Algorithmics/MIPS FPU Emulator v1.5 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs^Minit started: BusyBo^Mstarting pid 41, tty '': '/usr/etc/rcS'^M^Jx v1.12.1 (2017-12-21 19:51:32 CST)^M^J filesystem1:6.^M^JFreeing unused kernel memory:Algori.5^M^J 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs^Minmount: mounting none on /dev/pts failed: No such file or directory mount: mounting none on /proc/bus/usb failed: No such file or directory it started: BusyBo^Mstarting pid 41, tty '': '/usr/etc/rcS'^M^Jx v1.12.1 (2017-12-21 19:51:32 CST)^M^J filesystem1:6.^M^JFreeing unused kernel memory:Algori.5^M^J 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs^Minmount: mounting none on /dev/pts failed: No such file or directory^M^Jmount: mounting none on /proc/bus/usb failed: No such file or directory^M^Jit started: BusyBo^Mstarting pid 41, tty '': '/usr/etc/rcS'^M^Jx v1.12.1 (2017-12-21 19:51:32 CST)^M^J filesystem1:6.^M^JFreeing unused kernel memory:Algori.5^M^J 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs^Minmount: mounting none on /dev/pts failed: No such file or directory^M^Jmount: mounting none on /proc/bus/usb failed: No such file or directory^M^Jit started: BusyBo^Mstarting pid 41, tty '':^S '/usr/etc/rcS'^M^Jx v1.12.1 (2017-12-21 19:mknod: /dev/fuse: File exists Welcome to _______ _______ ___ __ ____ _ _ ___ | ___ \| __ || | |__|| \ | || | / / | |___| || |__| || |__ __ | \| || |/ / | _ /| _ || || || |\ || \ |__| \__\|__| |__||______||__||_| \____||_|\___\ =System Architecture Department= led_pb_api: module license 'Sercomm' taints kernel. Disabling lock debugging due to kernel taint ttyS1: 4 input overrun(s) [32m[SYSTEM]/bin/echo 1 > /proc/sys/net/ipv6/conf/all/Register LED ID <70> disable_ipv6[0mRegister LED ID <91> Register LED ID <10> Register LED ID <40> [32m[SYSTEM]/biRegister LED ID <46> n/echo =========Register LED ID <20> =====insmod starRegister LED ID <30> t > /dev/consoleRegister LED ID <62> [0m ==============insmod start [32m[SYSTEM]/sbin/insmod /lib/modules/`uname -r`/kernel/drivers/char/i2c_drv.ko[0m insmod: can't read '/lib/modules/2.6.36/kernel/drivers/char/i2c_drv.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/led_pb_api.ko[0m netfilter dnshj choose interested dns queries module loaded ! [32m[SYSTEM]/sbin/insmod /lib/modules/led_hw.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/ipt_condition.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/ipt_http_string.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/ipt_dnshj.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/ipt_DLOG.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/ipt_macblock_dnshj.ko[0m insmod: can't read '/lib/modules/ipt_macblock_dnshj.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/xt_ct_dir.ko[0m insmod: can't read '/lib/modules/xt_ct_dir.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/cnapt_core.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/cnapt.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/cpt.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/cpm.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/calg.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/cdmz.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/cudp.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/hairpin.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/natlimit.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/jnl.ko[0m insmod: can't read '/lib/modules/jnl.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/ufsd.ko[0m insmod: can't read '/lib/modules/ufsd.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/arp_protect_enable.ko[0m [32m[SYSTEM]/sbin/insmod /lib/modules/common.ko[0m insmod: can't read '/lib/modules/common.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/firewall_block.ko[0m insmod: can't read '/lib/modules/firewall_block.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/fake_source_dos.ko[0m insmod: can't read '/lib/modules/fake_source_dos.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/psd_and_special_udp_dos.ko[0m insmod: can't read '/lib/modules/psd_and_special_udp_dos.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/tcp_syn_dos.ko[0m insmod: can't read '/lib/modules/tcp_syn_dos.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/clamp_total_session_for_one_src.ko[0m insmod: can't read '/lib/modules/clamp_total_session_for_one_src.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/others_dos.ko[0m insmod: can't read '/lib/modules/others_dos.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/net/wireless/mt_wifi_ap/mt_wifi.ko[0m insmod: can't read '/lib/modules/2.6.36/kernel/drivers/net/wireless/mt_wifi_ap/mt_wifi.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/usb/core/usbcore.ko [0m insmod: can't read '/lib/modules/2.6.36/kernel/drivers/usb/core/usbcore.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/usb/host/ohci-hcd.ko [0m insmod: can't read '/lib/modules/2.6.36/kernel/drivers/usb/host/ohci-hcd.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/usb/host/ehci-hcd.ko [0m insmod: can't read '/lib/modules/2.6.36/kernel/drivers/usb/host/ehci-hcd.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/usb/storage/usb-storage.ko[0m insmod: can't read '/lib/modules/2.6.36/kernel/drivers/usb/storage/usb-storage.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/usb/serial/usbserial_filter.ko[0m insmod: can't read '/lib/modules/2.6.36/kernel/drivers/usb/serial/usbserial_filter.ko': No such file or directory [32m[SYSTEM]/sbin/insmod /lib/modules/2.6.36/kernel/drivers/net/wireless/rlt_wifi_ap/rlt_wifi.ko[0m register rt2860 === pAd = c0702000, size = 1734928 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 pAd->CSRBaseAddress =0xc0600000, csr_addr=0xc0600000! device_id =0x7662 ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 RtmpEepromGetDefault::e2p_dafault=2 NVM is efuse and the information is too less to bring up the interface Force to use Flash mode NVM is FLASH mode (pAd->flash_offset = 0x8000) get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai ttyS1: 12 input overrun(s) 0: C:43:FFFFFFE1:76:29 Raeth v3.1 (Tasklet) phy_tx_ring = 0x02e90000, tx_ring = 0xa2e90000 phy_rx_ring0 = 0x02e92000, rx_ring0 = 0xa2e92000 GMAC1_MAC_ADRH -- : 0x0000000c GMAC1_MAC_ADRL -- : 0x43e17629 RT305x_ESW: Link Status Changed reg_int_val is 4000000, 4000000 ra2880stop()...Done Free TX/RX Ring Memory! [32m[SYSTEM]mount -t usbfs none /proc/bus/usb/[0m mount: mounting none on /pr 0: C:43:FFFFFFE1:76:29 oc/bus/usb/ failRaeth v3.1 (ed: No such fileTasklet or directory ) [32m[SYSTEM]/bin phy_tx_ring = 0x036fa000, tx_ring = 0xa36fa000 /echo ========== phy_rx_ring0 = 0x036fc000, rx_ring0 = 0xa36fc000 ====insmod finish > /dev/console[0m ============GMAC1_MAC_ADRH -- : 0x0000000c ==insmod finishGMAC1_MAC_ADRL -- : 0x43e17629 [32m[SYSTEM]/uRT305x_ESW: Link Status Changed reg_int_val is 4000000, 4000000 sr/sbin/led_app blink_always 70 5 100 100 0[0m device eth2 entered promiscuous mode [32m[SYSTEM]/sbin/ifconfig eth2 up[0m [32m[SYSTEM]/sbin/ifconfig lo 127.0.0.0[0m [32m[SYSTEM]/sbin/route add -net 127.0.0.0 netmask 255.0.0.0 lo[0m [32m[SYSTEM]/bin/cp /proc/uptime /tmp/lan_uptime[0m [32m[SYSTEM]/sbin/ifconfig eth2.1 down[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/sbin/ifconfig eth2.2 down[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/sbin/ifconfig eth2 down[0m [32m[SYSTEM]/sbin/vconfig rem eth2.1[0m vconfig: ioctl error for rem: No such device [32m[SYSTEM]/sbin/vconfig rem eth2.2[0m vconfig: ioctl error for rem: No such device [32m[SYSTEM]/sbin/ifconfig eth2 up[0m [32m[SYSTEM]/sbin/vconfig add eth2 1[0m [32m[SYSTEM]/sbin/vconfig add eth2 2[0m [32m[SYSTEM]/sbin/ifconfig eth2.1 down[0m [32m[SYSTEM]/sbin/ifconfig eth2.1 hw ether 8C:3B:AD:EA:7B:3B [0m [32m[SYSTEM]/sbin/ifconfig eth2.1 up[0m [board_init/board_init.c::configure_mtk7628_switch():240] config-vlan.sh 2 LLLLW [32m[SYSTEM]/sbin/vconfig add eth2 1[0m vconfig: ioctl error for add: File exists [32m[SYSTEM]vconfig set_ingress_map $1 0 0[0m BusyBox v1.12.1 (2017-12-21 19:51:32 CST) multi-call binary Usage: vconfig COMMAND [OPTIONS]... [32m[SYSTEM]vconfig set_ingress_map eth2.1 1 1[0m [32m[SYSTEM]vconfig set_ingress_map eth2.1 2 2[0m [32m[SYSTEM]vconfig set_ingress_map eth2.1 3 3[0m [32m[SYSTEM]vconfig set_ingress_map eth2.1 4 4[0m [32m[SYSTEM]vconfig set_ingress_map eth2.1 5 5[0m [32m[SYSTEM]vconfig set_ingress_map eth2.1 6 6[0m [32m[SYSTEM]vconfig set_ingress_map eth2.1 7 7[0m [32m[SYSTEM]vconfig set_egress_map eth2.1 0 0[0m [32m[SYSTEM]vconfig set_egress_map eth2.1 1 1[0m [32m[SYSTEM]vconfig set_egress_map eth2.1 2 2[0m [32m[SYSTEM]vconfig set_egress_map eth2.1 3 3[0m [32m[SYSTEM]vconfig set_egress_map eth2.1 4 4[0m [32m[SYSTEM]vconfig set_egress_map eth2.1 5 5[0m [32m[SYSTEM]vconfig set_egress_map eth2.1 6 6[0m [32m[SYSTEM]vconfig set_egress_map eth2.1 7 7[0m [32m[SYSTEM]/sbin/vconfig add eth2 2[0m vconfig: ioctl error for add: File exists [32m[SYSTEM]vconfig set_ingress_map $1 0 0[0m BusyBox v1.12.1 (2017-12-21 19:51:32 CST) multi-call binary Usage: vconfig COMMAND [OPTIONS]... [32m[SYSTEM]vconfig set_ingress_map eth2.2 1 1[0m [32m[SYSTEM]vconfig set_ingress_map eth2.2 2 2[0m [32m[SYSTEM]vconfig set_ingress_map eth2.2 3 3[0m [32m[SYSTEM]vconfig set_ingress_map eth2.2 4 4[0m [32m[SYSTEM]vconfig set_ingress_map eth2.2 5 5[0m [32m[SYSTEM]vconfig set_ingress_map eth2.2 6 6[0m [32m[SYSTEM]vconfig set_ingress_map eth2.2 7 7[0m [32m[SYSTEM]vconfig set_egress_map eth2.2 0 0[0m [32m[SYSTEM]vconfig set_egress_map eth2.2 1 1[0m [32m[SYSTEM]vconfig set_egress_map eth2.2 2 2[0m [32m[SYSTEM]vconfig set_egress_map eth2.2 3 3[0m [32m[SYSTEM]vconfig set_egress_map eth2.2 4 4[0m [32m[SYSTEM]vconfig set_egress_map eth2.2 5 5[0m [32m[SYSTEM]vconfig set_egress_map eth2.2 6 6[0m [32m[SYSTEM]vconfig set_egress_map eth2.2 7 7[0m [32m[SYSTEM]/sbin/ifconfig eth2.1 up[0m [32m[SYSTEM]/sbin/brctl addif group1 eth2.1[0m interface eth2.1 does not exist! [32m[SYSTEM]/usr/sbin/config-vlan.sh 2 LLLLW[0m switch reg write offset=14, value=405555 switch reg write offset=50, value=2001 switch reg write offset=98, value=7f3f switch reg write offset=e4, value=3f switch reg write offset=40, value=1001 switch reg write offset=44, value=1001 switch reg write offset=48, value=1002 switch reg write offset=70, value=ffff506f Segmentation fault [32m[SYSTEM]/sbin/ifconfig eth2.2 up[0m [32m[SYSTEM]/usr/sbin/led_switch &[0m [32m[SYSTEM]/usr/sbin/mknod /dev/apsoc_nvram c 251 0[0m RC: wifi_init() [32m[SYSTEM]/usr/bin/killall access_logd[0m killall: access_logd: no process killed [32m[SYSTEM]/usr/sbin/rc access_log start[0m rcd: enQ=/usr/sbin/rc_app/rc_access_log start rcd: [run] deQ =/usr/sbin/rc_app/rc_access_log start [32m[SYSTEM]/usr/sbin/rc access_dev start[0m rcd: enQ=/usr/sbin/rc_app/rc_access_dev start killall: access_logd: no process killed [32m[SYSTEM]/usr/bin/insmod /lib/modules/ufsd.ko[0m insmod: can't read '/lib/modules/ufsd.ko': No such file or directory [32m[SYSTEM]/bin/echo ===============rc start > /dev/console[0m ===============rc start [32m[SYSTEM]/sbin/klogd&[0m [32m[SYSTEM]/usr/sbin/cmd_agent_ap[0m [32m[SYSTEM]/usr/sbin/cmd_agent&[0m [32m[SYSTEM]/usr/sbin/scfgmgr&[0m [32m[SYSTEM]/sbin/lan_monitor &[0m sh: /sbin/lan_monitor: not found [32m[SYSTEM]/sbin/rc syslogd start[0m rcd: enQ=/usr/sbin/rc_app/rc_syslogd start [32m[SYSTEM]/sbin/rc lan init[0m scfgmgr for local rcd: enQ=/usr/sbin/rc_app/rc_lan init [32m[SYSTEM]/sbin/rc firewall init[0m rcd: enQ=/usr/sbin/rc_app/rc_firewall init [32m[SYSTEM]/sbin/rc vlan start[0m rcd: enQ=/usr/sbin/rc_app/rc_vlan start [32m[SYSTEM]/sbin/rc lan start[0m rcd: enQ=/usr/sbin/rc_app/rc_lan start [32m[SYSTEM]/sbin/rc lan reset_switch[0m rcd: enQ=/usr/sbin/rc_app/rc_lan reset_switch [32m[SYSTEM]/sbin/rc wlan start[0m rcd: enQ=/usr/sbin/rc_app/rc_wlan start [32m[SYSTEM]/sbin/rc wifi_isolation start[0m rcd: enQ=/usr/sbin/rc_app/rc_wifi_isolation start [32m[SYSTEM]/sbin/rc timezone start[0m rcd: enQ=/usr/sbin/rc_app/rc_timezone start [32m[SYSTEM]/sbin/rc sip_alg start[0m rcd: enQ=/usr/sbin/rc_app/rc_sip_alg start [32m[SYSTEM]/sbin/rc mediaserver start[0m rcd: enQ=/usr/sbin/rc_app/rc_mediaserver start [32m[SYSTEM]/sbin/rc dnrd start[0m rcd: enQ=/usr/sbin/rc_app/rc_dnrd start [32m[SYSTEM]/sbin/rc debug_mode start&[0m [32m[SYSTEM]/sbin/rc httpd start[0m rcd: enQ=/usr/sbin/rc_app/rc_debug_mode start rcd: enQ=/usr/sbin/rc_app/rc_httpd start [32m[SYSTEM]/sbin/rc httpd remote start[0m rcd: enQ=/usr/sbin/rc_app/rc_httpd remote start [32m[SYSTEM]/sbin/rc printk start[0m rcd: enQ=/usr/sbin/rc_app/rc_printk start [32m[SYSTEM]/sbin/rc ntp start[0m rcd: enQ=/usr/sbin/rc_app/rc_ntp start [32m[SYSTEM]/sbin/rc ddns init[0m rcd: enQ=/usr/sbin/rc_app/rc_ddns init [32m[SYSTEM]/sbin/rc wan init[0m rcd: enQ=/usr/sbin/rc_app/rc_wan init [32m[SYSTEM]/sbin/rc route start[0m rcd: enQ=/usr/sbin/rc_app/rc_route start [32m[SYSTEM]/sbin/rc ripd start[0m rcd: enQ=/usr/sbin/rc_app/rc_ripd start [32m[SYSTEM]/sbin/rc potcounter start[0m rcd: enQ=/usr/sbin/rc_app/rc_potcounter start [32m[SYSTEM]/sbin/rc lltd start[0m rcd: enQ=/usr/sbin/rc_app/rc_lltd start [32m[SYSTEM]/sbin/rc upnp start[0m rcd: enQ=/usr/sbin/rc_app/rc_upnp start [32m[SYSTEM]/sbin/rc schedule start[0m rcd: enQ=/usr/sbin/rc_app/rc_schedule start [32m[SYSTEM]/sbin/rc access_dev start[0m rcd: enQ=/usr/sbin/rc_app/rc_access_dev start [32m[SYSTEM]/etc/ad_arpd &[0m [32m[SYSTEM]/usr/sbin/crond &[0m [32m[SYSTEM]/usr/sbin/multi_pb_app &[0m [32m[SYSTEM]/usr/sbin/wlevt[0m sh: /usr/sbin/wlevt: not found [32m[SYSTEM]/etc/prepare_3g[0m sh: /etc/prepare_3g: not found [32m[SYSTEM]/usr/sbin/rc usb_printer start[0m rcd: enQ=/usr/sbin/rc_app/rc_usb_printer start [32m[SYSTEM]/etc/turn_on_printer_led[0m cat: can't open '/proc/bus/usb/devices': No such file or directory cat: can't open '/proc/bus/usb/devices': No such file or directory rcd: enQ=/usr/sbin/rc_app/rc_check_conn start [32m[SYSTEM]/sbin/rc start finished[0m rcd: enQ=/usr/sbin/rc_app/rc_start finished [32m[SYSTEM]/bin/echo ===============rc finish > /dev/console[0m ===============rc finish [32m[SYSTEM]/bin/ps[0m PID USER VSZ STAT COMMAND 1 root 1532 S init 2 root 0 SW [kthreadd] 3 root 0 SW [ksoftirqd/0] 4 root 0 SW [kworker/0:0] 5 root 0 SW [kworker/u:0] 6 root 0 SW< [khelper] 7 root 0 SW [sync_supers] 8 root 0 SW [bdi-default] 9 root 0 SW< [kblockd] 10 root 0 SW [kswapd0] 11 root 0 SW< [crypto] 20 root 0 SW [mtdblock0] 21 root 0 SW [mtdblock1] 22 root 0 SW [mtdblock2] 23 root 0 SW [mtdblock3] 24 root 0 SW [mtdblock4] 25 root 0 SW [mtdblock5] 26 root 0 SW [mtdblock6] 27 root 0 SW [mtdblock7] 28 root 0 SW [mtdblock8] 29 root 0 SW [mtdblock9] 30 root 0 SW [mtdblock10] 31 root 0 SW [mtdblock11] 32 root 0 SW [kworker/u:1] 39 root 0 SW [kworker/0:1] 41 root 1532 S /bin/sh /usr/etc/rcS 298 root 1412 S /usr/sbin/led_switch 309 root 936 S /usr/sbin/rcd 312 root 2760 S /usr/sbin/rc_app/rc_access_log start 319 root 2776 S /usr/sbin/rc_app/rc_start 323 root 928 S /sbin/klogd 326 root 928 S /usr/sbin/cmd_agent_ap 330 root 932 S /usr/sbin/cmd_agent 340 root 1400 S /usr/sbin/scfgmgr 390 root 1528 S /bin/sh /etc/ad_arpd 393 root 952 S /usr/sbin/crond 395 root 1440 S /usr/sbin/multi_pb_app 399 root 1524 S sleep 30 425 root 1528 S sh -c /bin/ps 426 root 1532 R /bin/ps =============proc init sh: cannot create /proc/sys/net/ipv4/conf/group1/forwarding: nonexistent directory sh: cannot create /proc/sys/net/ipv4/conf/wlan0/forwarding: nonexistent directory sh: cannot create /proc/sys/net/ipv4/conf/wlan0-va0/forwarding: nonexistent directory sh: cannot create /proc/sys/net/ipv4/conf/eth1/rp_filter: nonexistent directory [32m[SYSTEM]/bin/echo 8 > /proc/sys/kernel/printk[0m =============proc finish starting pid 480, tty '/dev/ttyS1': '/bin/sh' # andelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (s quashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech .com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kerne l memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs file system1:6.^M^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 16 0k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M ^JFreeing unused kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freed^M^J andelatech.com>^M^JAll bugs added by Daot (squashfs filesystem1:6.^M^JFreeing un used kernel memory: 160k freed^M^Jandelatech.com>^M^JAll bugs added by Daot (squ ashfs filesystem1:6.^M^JFreeing unused kernel memory: 160k freedrcd: [run] deQ =/usr/sbin/rc_app/rc_access_dev start killall: access_devinfo: no process killed rcd: [run] deQ =/usr/sbin/rc_app/rc_syslogd start [32m[SYSTEM]/sbin/syslogd -f /etc/syslog.conf[0m rcd: [run] deQ =/usr/sbin/rc_app/rc_lan init [32m[SYSTEM]/usr/sbin/brctl addbr group1[0m [32m[SYSTEM]/sbin/ifconfig group1 up[0m [32m[SYSTEM]/usr/sbin/brctl addbr group2[0m [32m[SYSTEM]/sbin/ifconfig group2 up[0m rcd: [run] deQ =/usr/sbin/rc_app/rc_firewall init [ firewall_main - 133 ] : before fw_exe [ firewall_main - 136 ] : end fw_exe iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: Bad rule (does a matching rule exist in that chain?). [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. rcd: [run] deQ =/usr/sbin/rc_app/rc_vlan start rcd: [run] deQ =/usr/sbin/rc_app/rc_lan start [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=0000000device eth2.1 entered promiscuous mode 0 [32m[SYSTEM]group1: port 1(eth2.1) entering learning state /sbin/ifconfig egroup1: port 1(eth2.1) entering learning state th2.1 up[0m [32m[SYSTEM]/usr/sbin/brctl addif group1 eth2.1[0m [ start_lan_group1: port 1(eth2.1) entering learning state vlan_L2 - 884 ] : guest interface ra0 NOT enabled [ start_lan_vgroup1: port 1(eth2.1) entering learning state lan_L2 - 884 ] :group1: port 1(eth2.1) entering learning state guest interface ra1 NOT enabled [ start_lan_vlan_L2 - 908 ] : guest interface rai0 NOT enabled [ start_lan_vlan_L2 - 908 ] : guest interface rai1 NOT enabled [32m[SYSTEM]/sbin/ifconfig group1 down[0m [32m[SYSTEM]/sbin/ifconfig group1 up[0m [32m[SYSTEM]/usr/sbin/brctl setfd group1 1[0m [32m[SYSTEM]/usr/sbin/brctl stp group1 on[0m [ start_lan_vlan_L3 - 806 ] : index:1, wan:1 2 3 [32m[SYSTEM]/usr/bdns_hijack_module installed. in/insmod /lib/modules/dns_hijack.ko[0m [32m[SYSTEM]/usr/bin/fc disable[0m sh: /usr/bin/fc: not found [32m[SYSTEM]/usr/bin/rmmod pktrunner[0m rmmod: pktrunner: No such file or directory [32m[SYSTEM]/usr/bin/rc access_dev start[0m rcd: enQ=/usr/sbin/rc_app/rc_access_dev start [32m[SYSTEM]/usr/bin/rc access_log start[0m rcd: enQ=/usr/sbin/rc_app/rc_access_log start [32m[SYSTEM]/bin/ln -sf /usr/sbin/udhcpc /var/w/udhcpc_1[0m [32m[SYSTEM]/var/w/udhcpc_1 -i group1 -s /etc/udhcpc.ap.script -w 1 -o /tmp/w/info_1&[0m [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [32m[SYSTEM]/sbin/ifconfig eth2.1 up[0m [32m[SYSTEM]/usr/sbin/brctl addif group2 eth2.1[0m device eth2.1 is already a member of a bridge; can't enslave it to bridge group2. [32m[SYSTEM]/sbin/ifconfig group2 down[0m [32m[SYSTEM]/sbin/ifconfig group2 up[0m [32m[SYSTEM]/usr/sbin/brctl setfd group2 1[0m [32m[SYSTEM]/usr/sbin/brctl stp group2 on[0m [ start_lan_vlan_L3 - 806 ] : index:2, wan:1 2 3 [32m[SYSTEM]/usr/bin/insmod /lib/modules/dns_hijack.ko[0m insmod: cannot insert '/lib/modules/dns_hijack.ko': File exists [32m[SYSTEM]/usr/bin/fc disable[0m sh: /usr/bin/fc: not found [32m[SYSTEM]/usr/bin/rmmod pktrunner[0m rmmod: pktrunner: No such file or directory [32m[SYSTEM]/usr/bin/rc access_dev start[0m rcd: enQ=/usr/sbin/rc_app/rc_access_dev start [32m[SYSTEM]/usr/bin/rc access_log start[0m rcd: enQ=/usr/sbin/rc_app/rc_access_log start [32m[SYSTEM]/bin/ln -sf /usr/sbin/udhcpc /var/w/udhcpc_2[0m [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [32m[SYSTEM]/sbin/ifconfig eth2.1 up[0m [32m[SYSTEM]/usr/sbin/brctl addif group3 eth2.1[0m interface eth2.1 does not exist! [32m[SYSTEM]/sbin/ifconfig group3 down[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/sbin/ifconfig group3 up[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/usr/sbin/brctl setfd group3 1[0m set forward delay failed: No such device [32m[SYSTEM]/usr/sbin/brctl stp group3 on[0m set stp status failed: No such device [ start_lan_vlan_L3 - 806 ] : index:3, wan:1 2 3 [32m[SYSTEM]/usr/bin/insmod /lib/modules/dns_hijack.ko[0m insmod: cannot insert '/lib/modules/dns_hijack.ko': File exists [32m[SYSTEM]/usr/bin/fc disable[0m sh: /usr/bin/fc: not found [32m[SYSTEM]/usr/bin/rmmod pktrunner[0m rmmod: pktrunner: No such file or directory [32m[SYSTEM]/usr/bin/rc access_dev start[0m rcd: enQ=/usr/sbin/rc_app/rc_access_dev start [32m[SYSTEM]/usr/bin/rc access_log start[0m rcd: enQ=/usr/sbin/rc_app/rc_access_log start [32m[SYSTEM]/bin/ln -sf /usr/sbin/udhcpc /var/w/udhcpc_3[0m [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [32m[SYSTEM]/sbin/ifconfig eth2.1 up[0m [32m[SYSTEM]/usr/sbin/brctl addif group4 eth2.1[0m interface eth2.1 does not exist! [32m[SYSTEM]/sbin/ifconfig group4 down[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/sbin/ifconfig group4 up[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/usr/sbin/brctl setfd group4 1[0m set forward delay failed: No such device [32m[SYSTEM]/usr/sbin/brctl stp group4 on[0m set stp status failed: No such device [ start_lan_vlan_L3 - 806 ] : index:4, wan:1 2 3 [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [32m[SYSTEM]/sbin/ifconfig eth2.1 up[0m [32m[SYSTEM]/usr/sbin/brctl addif group5 eth2.1[0m interface eth2.1 does not exist! [32m[SYSTEM]/sbin/ifconfig group5 down[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/sbin/ifconfig group5 up[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/usr/sbin/brctl setfd group5 1[0m set forward delay failed: No such device [32m[SYSTEM]/usr/sbin/brctl stp group5 on[0m set stp status failed: No such device [ start_lan_vlan_L3 - 806 ] : index:5, wan:1 2 3 [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [32m[SYSTEM]/sbin/ifconfig eth2.1 up[0m [32m[SYSTEM]/usr/sbin/brctl addif group6 eth2.1[0m interface eth2.1 does not exist! [32m[SYSTEM]/sbin/ifconfig group6 down[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/sbin/ifconfig group6 up[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/usr/sbin/brctl setfd group6 1[0m set forward delay failed: No such device [32m[SYSTEM]/usr/sbin/brctl stp group6 on[0m set stp status failed: No such device [ start_lan_vlan_L3 - 806 ] : index:6, wan:1 2 3 [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [32m[SYSTEM]/sbin/ifconfig eth2.1 up[0m [32m[SYSTEM]/usr/sbin/brctl addif group7 eth2.1[0m interface eth2.1 does not exist! [32m[SYSTEM]/sbin/ifconfig group7 down[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/sbin/ifconfig group7 up[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/usr/sbin/brctl setfd group7 1[0m set forward delay failed: No such device [32m[SYSTEM]/usr/sbin/brctl stp group7 on[0m set stp status failed: No such device [ start_lan_vlan_L3 - 806 ] : index:7, wan:1 2 3 [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [32m[SYSTEM]/sbin/ifconfig eth2.1 up[0m [32m[SYSTEM]/usr/sbin/brctl addif group8 eth2.1[0m interface eth2.1 does not exist! [32m[SYSTEM]/sbin/ifconfig group8 down[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/sbin/ifconfig group8 up[0m ifconfig: SIOCGIFFLAGS: No such device [32m[SYSTEM]/usr/sbin/brctl setfd group8 1[0m set forward delay failed: No such device [32m[SYSTEM]/usr/sbin/brctl stp group8 on[0m set stp status failed: No such device [ start_lan_vlan_L3 - 806 ] : index:8, wan:1 2 3 rcd: [run] deQ =/usr/sbin/rc_app/rc_lan reset_switch down port 0 Set: phy[0].reg[0] = 1840 down port 1 Set: phy[1].reg[0] = 1840 down port 2 Set: phy[2].reg[0] = 1840 down port 3 Set: phy[3].reg[0] = 1840 up port 0 Set: phy[0].reg[0] = 1240 up port 1 Set: phy[1].reg[0] = 1240 up port 2 Set: phy[2].reg[0] = 1240 up port 3 Set: phy[3].reg[0] = 1240 rcd: [run] deQ =/usr/sbin/rc_app/rc_wlan start [wlan/wifi.c::sync_wireless_nvram():2229] wifi_super_wifi_enable:0, wifi_powerpercent:100, wifi_super_wifi_enable1:0, wifi_powerpercent1:100 [32m[SYSTEM]mkdir -p /etc/Wireless/RT2860[0m [32m[SYSTEM]mkdir -p /etc/Wireless/iNIC[0m [wlan/wifi.c::start_wireless():2389] Check WiFi Config. [wlan/wifi.c::start_wireless():2398] Check 11AC support. [wlan/wifi.c::start_wireless():2400] SC 5G support level: 11ac [wlan/wifi.c::start_wireless():2402] Check guest_led REPLACE usb_led. [32m[SYSTEM]/bin/led_app setval guest_led_replace 0 [0m [wlan/wifi.c::start_wireless():2407] guest_led REPLACE usb_led: OFF [32m[SYSTEM]/bin/rm -rf /etc/Wireless/RT2860/SingleSKU-2.4.dat[0m [32m[SYSTEM]/bin/rm -rf /etc/Wireless/iNIC/SingleSKU-5G.dat[0m [32m[SYSTEM]/bin/cp /usr/etc/mtk/singlesku/AU/SingSku-2.4.dat /etc/Wireless/RT2860/SingleSKU-2.4.dat[0m [32m[SYSTEM]/bin/cp /usr/etc/mtk/singlesku/AU/SingSku-5G.dat /etc/Wireless/iNIC/SingleSKU-5G.dat[0m [libscm_wl.c::set_ralink_wifi_mac():1637] CHIP: 7628 - current MAC: 8C:3B:AD:EA:7B:3B [libscm_wl.c::set_ralink_wifi_mac():1638] Assign MAC: 8C:3B:AD:EA:7B:3B [libscm_wl.c::set_ralink_wifi_mac():1641] no update! [libscm_wl.c::set_ralink_wifi_mac():1637] CHIP: 7662 - current MAC: 8C:3B:AD:EA:7B:3D [libscm_wl.c::set_ralink_wifi_mac():1638] Assign MAC: 8C:3B:AD:ea:7b:3d [libscm_wl.c::set_ralink_wifi_mac():1641] no update! [32m[SYSTEM]echo 1 > /tmp/wifi_mac_set[0m [32m[SYSTEM]/sbin/ifconfig ra0 up[0m TX_BCN DESC a3f03000 size = 320 RX[0] DESC a3f06000 size = 1024 RX[1] DESC a3f07000 size = 1024 E2pAccessMode=2 cfg_mode=9 cfg_mode=9 wmode_band_equal(): Band Equal! AndesSendCmdMsg: Could not send in band command due to diable fRTMP_ADAPTER_MCU_SEND_IN_BAND_CMD APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) WscKeyASCII=1 RTMPSetDefaultChannel() : default channel to 1 load fw image from fw_header_image AndesMTLoadFwMethod1(2182)::pChipCap->fw_len(63888) FW Version:20151201 FW Build Date:20151201183641 CmdAddressLenReq:(ret = 0) CmdFwStartReq: override = 1, address = 1048576 CmdStartDLRsp: WiFI FW Download Success MtAsicDMASchedulerInit(): DMA Scheduler Mode=0(LMAC) efuse_probe: efuse = 10000002 RtmpChipOpsEepromHook::e2p_type=2, inf_Type=4 RtmpEepromGetDefault::e2p_dafault=2 RtmpChipOpsEepromHook: E2P type(2), E2pAccessMode = 2, E2P default = 2 NVM is FLASH mode 1. Phy Mode = 14 Country Region from e2p = ffff tssi_1_target_pwr_g_band = 38 2. Phy Mode = 14 3. Phy Mode = 14 NICInitPwrPinCfg(11): Not support for HIF_MT yet! NICInitializeAsic(651): Not support rtmp_mac_sys_reset () for HIF_MT yet! mt_mac_init()--> MtAsicInitMac()--> mt7628_init_mac_cr()--> MtAsicSetMacMaxLen(1276): Set the Max RxPktLen=1024! <--mt_mac_init() WTBL Segment 1 info: MemBaseAddr/FID:0x28000/0 EntrySize/Cnt:32/128 WTBL Segment 2 info: MemBaseAddr/FID:0x40000/0 EntrySize/Cnt:64/128 WTBL Segment 3 info: MemBaseAddr/FID:0x42000/64 EntrySize/Cnt:64/128 WTBL Segment 4 info: MemBaseAddr/FID:0x44000/128 EntrySize/Cnt:32/128 AntCfgInit(2947): Not support for HIF_MT yet! MCS Set = ff ff 00 00 01 MtAsicSetChBusyStat(861): Not support for HIF_MT yet! CmdSlotTimeSet:(ret = 0) SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l SYNC - BBP R4 to 20MHz.l MtAsicSetRalinkBurstMode(3047): Not support for HIF_MT yet! MtAsicSetPiggyBack(796): Not support for HIF_MT yet! reload DPD from flash , 0x9F = [c100] doReload bit7[0] CmdLoadDPDDataFromFlash: Channel = 3, DoReload = 0 MtAsicSetTxPreamble(3026): Not support for HIF_MT yet! MtAsicAddSharedKeyEntry(1343): Not support for HIF_MT yet! The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2 MtAsicSetPreTbtt(): bss_idx=0, PreTBTT timeout = 0xf0 Main bssid = 8c:3b:ad:ea:7b:3b <==== rt28xx_init, Status=0 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== mt7628_set_ed_cca: TURN ON EDCCA mac 0x10618 = 0xd7c87d0f, EDCCA_Status=1 WiFi Startup Cost (ra0): 6.708s [32m[SYSTEM]/sb ==== @@@ ed_status_read: EDCCA TH - H pAd->ed_trigger_cnt : 0 > 20 || pAd->ed_big_rssi_stat : 0 < 50 ==== in/brctl addif group1 ra0[0m device ra0 entered promiscuous mode group1: port 2(ra0) entering listening state group1: port 2(ra0) entering listening state [32m[SYSTEM]/bin/led_app on 40[0m [32m[SYSTEM]/bin/led_app on 41[0m [wlan/wifi.c::start_wireless():2469] no need fixbuild time = f2 f3 value sin2ce this is 54M t0arget power and 1NTGR need other 4value [32m[SYS1TEM]/sbin/ifconf1ig rai0 up[0m 15060606a rom patch for E3 IC platform = ALPS hw/sw version = ŠŠ patch version = FW Version:0.0.00 Build:1 Build Time:201507311614____ fw for E3 IC RX[0] DESC a363f000 size = 4096 RX[1] DESC a3668000 size = 4096 E2pAccessMode=2 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Not Equal! APSDCapable[0]=0 APSDCapable[1]=0 APSDCapable[2]=0 APSDCapable[3]=0 APSDCapable[4]=0 APSDCapable[5]=0 APSDCapable[6]=0 APSDCapable[7]=0 APSDCapable[8]=0 APSDCapable[9]=0 APSDCapable[10]=0 APSDCapable[11]=0 APSDCapable[12]=0 APSDCapable[13]=0 APSDCapable[14]=0 APSDCapable[15]=0 Key1Str is Invalid key length(0) or Type(0) Key1Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key2Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key3Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) Key4Str is Invalid key length(0) or Type(0) 1. Phy Mode = 49 get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (167) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (169) get_chl_grp:illegal channel (171) get_chl_grp:illegal channel (171) drivers/net/wireless/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:2899 assert (ad->TxPower[choffset].Channel == 42)failed Country Region from e2p = ffff mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0 mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=0, ePA_type=3 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 mt76x2_get_external_lna_gain::LNA type=0x11, BLNAGain=0x0, ALNAGain0=0x0, ALNAGain1=0x0, ALNAGain2=0x0 2. Phy Mode = 49 3. Phy Mode = 49 andes_pci_fw_init 0x1300 = 00073200 AntCfgInit: primary/secondary ant 0/1 andes_load_cr:cr_type(2) ChipStructAssign(): MT76x2 hook ! RTMPSetPhyMode: channel is out of range, use first channel=0 MCS Set = ff ff 00 00 01 TX0 power compensation = 0x38 TX1 power compensation = 0x38 group1: port 2(ra0) entering learning state PATH=/sbin:/bin:/usr/sbin:/usr/bin::/usr/local/sbin:/var/sbin ap1: dhcpc FAIL /etc/udhcpc.ap.script: line 94: /etc/dhclient-exit-hook.in: not found group1: topology change detected, propagating group1: port 2(ra0) entering forwarding state group1: topology change detected, propagating group1: port 1(eth2.1) entering forwarding state mt76x2_bbp_adjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42 APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) mt76x2_calibration(channel = 42) The 2-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 2 Main bssid = 8c:3b:ad:ea:7b:3d mt76x2_reinit_agc_gain:original agc_vga0 = 0x5c, agc_vga1 = 0x5c mt76x2_reinit_agc_gain:updated agc_vga0 = 0x5c, agc_vga1 = 0x5c mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x27, hi_lna1 = 0x27 mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x27, hi_lna1 = 0x27 original vga value(chain0) = 5c original vga value(chain1) = 5c <==== rt28xx_init, Status=0 get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! [32m[SYSTEM]/sbin/brctl addif group1 rai0[0m device rai0 entered promiscuous mode group1: port 3(rai0) entering listening state group1: port 3(rai0) entering listening state [32m[SYSTEM]/bin/led_app on 40[0m [32m[SYSTEM]/bin/led_app on 42[0m [wlan/wifi.c::start_wireless():2493] no need fix f2 f3 value since this is 54M target power and NTGR need other value [libscm_wl.c::GenerateUUID():135] GUI ASCII string: 38833092-3092-1883-898a-8c3badea7b3b [libscm_wl.c::GenerateUUID():136] GUI HEX string: 3883309230921883898a8c3badea7b3b [ has_8021x - 292 ] : 8021x none for band WIFI_BAND_2G [ has_8021x - 292 ] : 8021x none for band WIFI_BAND_5G [32m[SYSTEM]/usr/bin/killall miniupnpd_wsc[0m killall: miniupnpd_wsc: no process killed [32m[SYSTEM]/sbin/chmod +x /var/ralink_ap_start.sh[0m [32m[SYSTEM]/bin/sh -x /var/ralink_ap_start.sh[0m + iwpriv ra0 set WscConfMode=0 + iwpriv rai0 set WscConfMode=0 + iwpriv ra0 set WscSetupLock=0 + iwpriv rai0 set WscSetupLock=0 + iwpriv ra0 set WscMaxPinAttack=3 + iwpriv rai0 set WscMaxPinAttack=3 + route add -host 239.255.255.250 dev group1 + iwpriv ra0 set WscConfMode=7 + iwpriv rai0 set WscConfMode=7 + miniupnpd_wsc -m 1 -I ra0 -P /var/run/miniupnpd.ra0 -i eth2.2 -a 192.168.1.1 -n 7777 -u 38833092-3092-1883-898a-8c3badea7b3b Unknown option: -I Unknown option: ra0 + sleep 10 [32m[SYSTEM]/bin/cp /proc/uptime /tmp/wlan_uptime[0m + sleep 10 + sleep 10 + sleep 10 [32m[SYSTEM]/bin/led_app on 44[0m [32m[SYSTEM]/usr/sbin/led_app off 45[0m [wlan/wifi.c::need_disable_edcca():2239] wifiregion_in_gui:Australia [wlan/wifi.c::start_wireless():2554] DISABLE EDCCA for 2G and 5G [32m[SYSTEM]/usr/sbin/iwpriv rai0 mac 1340[0m rai0 mac: [0x1340]:0400583f [wlan/wifi.c::start_wireless():2579] org:0x400583f. (0400583f )[wlan/wifi.c::start_wireless():2581] now:0x400583f [32m[SYSTEM]/usr/sbin/iwpriv rai0 mac 1340=400583f[0m rai0 mac: [0x1340]:0400583f net/netfilter/nf_conntrack_sip.c: write_proc: file: 82f26460, buffer: 1 , count: 2, data: 00000000 [32m[SYSTEM]/usr/sbin/iwpriv rai0 mac 1340[0m rai0 mac: [0x1340]:0400583f rcd: [run] deQ =/usr/sbin/rc_app/rc_wifi_isolation start [wifi_isolation/wifi_isolation.c::start_wifi_isolation():107] AP Mode no need wifi_isolation! rcd: [run] deQ =/usr/sbin/rc_app/rc_timezone start [32m[SYSTEM]/bin/echo GMT-10 > /etc/TZ[0m rcd: [run] deQ =/usr/sbin/rc_app/rc_sip_alg start [32m[SYSTEM]/bin/echo 1 > /proc/sipalg_enable[0m rcd: [run] deQ =/usr/sbin/rc_app/rc_mediaserver start rcd: an error occurred in execvp rcd: [run] deQ =/usr/sbin/rc_app/rc_dnrd start [ dnrd_main - 34 ] : do dnrd for 1 -> 1 [32m[SYSTEM]iptables -t nat -D PREROUTING -i group1 -p tcp --dport 80 -j DNAT --to 192.168.1.1:80[0m iptables: No chain/target/match by that name. [32m[SYSTEM]iptables -t nat -D PREROUTING -i group1 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.1.1[0m iptables: No chain/target/match by that name. [32m[SYSTEM]iptables -t nat -D PREROUTING -i group1 -p udp --dport 53 -j DNAT --to 192.168.1.1[0m iptables: No chain/target/match by that name. [32m[SYSTEM]iptables -t nat -D PREROUTING -i group1 -d 66.114.62.22 -p tcp --dport 80 -j RETURN[0m iptables: Bad rule (does a matching rule exist in that chain?). [32m[SYSTEM]iptables -t nat -D PREROUTING -i group1 -d 66.114.62.29 -p tcp --dport 80 -j RETURN[0m iptables: Bad rule (does a matching rule exist in that chain?). [32m[SYSTEM]iptables -t nat -D PREROUTING -i group1 -d 174.35.24.133 -p tcp --dport 80 -j RETURN[0m iptables: Bad rule (does a matching rule exist in that chain?). [32m[SYSTEM]iptables -t nat -D PREROUTING -i group1 -d 101.96.10.64 -p tcp --dport 80 -j RETURN[0m iptables: Bad rule (does a matching rule exist in that chain?). [32m[SYSTEM]iptables -t nat -I PREROUTING -i group1 -d 66.114.62.22 -p tcp --dport 80 -j RETURN[0m [32m[SYSTEM]iptables -t nat -I PREROUTING -i group1 -d 66.114.62.29 -p tcp --dport 80 -j RETURN[0m [32m[SYSTEM]iptables -t nat -I PREROUTING -i group1 -d 174.35.24.133 -p tcp --dport 80 -j RETURN[0m [32m[SYSTEM]iptables -t nat -I PREROUTING -i group1 -d 101.96.10.64 -p tcp --dport 80 -j RETURN[0m [32m[SYSTEM]/bin/killall -9 dnrd_1 2>/dev/null[0m [32m[SYSTEM]/bin/killall -9 dnrd_1 2>/dev/null[0m [32m[SYSTEM]/bin/ln -sf /usr/sbin/dnrd /var/dnrd_1[0m [32m[SYSTEM]/var/dnrd_1 -a 192.168.1.1 -m hosts -c off -r 0 -s 8.8.8.8 -o 0 -q xxx&[0m [32m[SYSTEM]iptables -t nat -I PREROUTING -i group1 -p udp --dport 53 -m dnshj -j DNAT --to 192.168.1.1[0m ERROR: isock: Couldn't bind local address rcd: [run] deQ =/usr/sbin/rc_app/rc_debug_mode start rcd: [run] deQ =/usr/sbin/rc_app/rc_httpd start group1: port 3(rai0) entering learning state group1: topology change detected, propagating group1: port 3(rai0) entering forwarding state [32m[SYSTEM]/bin/cat /www.eng/block.htm | /bin/sed "s|@model_name#|R6020|g" > /etc/block.htm[0m rmmod: ipt_REJECT: No such file or directory rcd: enQ=/usr/sbin/rc_app/rc_firewall restart [32m[SYSTEM]/usr/sbin/mini_httpd -d /www -r "NETGEAR R6020" -c '**.cgi' -t 300&[0m rcd: [run] deQ =/usr/sbin/rc_app/rc_httpd remote start rcd: [run] deQ =/usr/sbin/rc_app/rc_printk start [32m[SYSTEM]/bin/echo 1 4 1 7 > /proc/sys/kernel/printk[0m rcd: [run] deQ =/usr/sbin/rc_app/rc_ntp start [32m[SYSTEM]/usr/sbin/netgear_ntp -z GMT-10& [0m rcd: [run] deQ =/usr/sbin/rc_app/rc_ddns init [ddns/ddns_cfg.c::ddns_init():474] +++ddns is disable, not need init++++ rcd: [run] deQ =/usr/sbin/rc_app/rc_wan init [ wan_main - 651 ] : rc wan enter [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [32m[SYSTEM]/bin/wan_monitor &[0m rcd: [run] deQ =/usr/sbin/rc_app/rc_route start rcd: [run] deQ =/usr/sbin/rc_app/rc_ripd start rcd: [run] deQ =/usr/sbin/rc_app/rc_potcounter start killall: potcounter: no process killed rcd: [run] deQ =/usr/sbin/rc_app/rc_lltd start [32m[SYSTEM]/usr/bin/lld2 group1[0m rcd: [run] deQ =/usr/sbin/rc_app/rc_upnp start [32m[SYSTEM]/usr/bin/killall miniupnpd[0m killall: miniupnpd: no process killed [32m[SYSTEM]rc wan restart[0m rcd: enQ=/usr/sbin/rc_app/rc_wan restart [upnp/upnp_cfg.c::start_upnp():117] AP Mode no need upnp rcd: [run] deQ =/usr/sbin/rc_app/rc_schedule start [flash.c::sc_get_region():632] Original Region Data: 00, 0a [32m[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab[0m set crontab for wifi_schedule --- 0 [32m[SYSTEM]/bin/echo GMT-10 > /etc/TZ[0m [32m[SYSTEM]echo 1 > /proc/net/ipt_condition/schedule [0m sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory rcd: [run] deQ =/usr/sbin/rc_app/rc_access_dev start killall: access_devinfo: no process killed rcd: [run] deQ =/usr/sbin/rc_app/rc_usb_printer start rcd: an error occurred in execvp rcd: [run] deQ =/usr/sbin/rc_app/rc_check_conn start rcd: [run] deQ =/usr/sbin/rc_app/rc_start finished [32m[SYSTEM]/etc/enlarge_mem_reclaim_threshold.sh [0m [32m[SYSTEM]/usr/sbin/watchdog &[0m [32m[SYSTEM]/usr/sbin/echo > /tmp/bootup_finished[0m [watchdog.c::main():81] Watchdog: monitoring process 'mini_httpd' [watchdog.c::main():110] Watchdog: process 'mini_httpd' exists, score: 5. [start/start_cfg.c::bind_busydaemon_to_free_cpu():271] pid_multi_pb_app:395, pid_led_switch:298 [32m[SYSTEM]/sbin/taskset -p 4 395[0m pid 395's current affinity mask: 1 taskset: can't set pid 395's affinity: Invalid argument [32m[SYSTEM]/sbin/taskset -p 4 298[0m pid 298's current affinity mask: 1 taskset: can't set pid 298's affinity: Invalid argument rcd: [run] deQ =/usr/sbin/rc_app/rc_access_dev start killall: access_devinfo: no process killed rcd: [run] deQ =/usr/sbin/rc_app/rc_access_log start killall: access_logd: no process killed rcd: [run] deQ =/usr/sbin/rc_app/rc_access_dev start killall: access_devinfo: no process killed rcd: [run] deQ =/usr/sbin/rc_app/rc_access_log start killall: access_logd: no process killed + brctl addif group1 ra1 + brctl addif group1 ra0 + brctl addif group1 rai0 + brctl addif group1 rai1 device rai0 is already a member of a bridge; can't enslave it to bridge group1. device ra0 is already a member of a bridge; can't enslave it to bridge group1. rcd: [run] deQ =/usr/sbin/rc_app/rc_access_dev start killall: access_devinfo: no process killed rcd: [run] deQ =/usr/sbin/rc_app/rc_access_log start killall: access_logd: no process killed rcd: [run] deQ =/usr/sbin/rc_app/rc_firewall restart [ firewall_main - 133 ] : before fw_exe [32m[SYSTEM]/usr/sbin/rc schedule restart[0m rcd: enQ=/usr/sbin/rc_app/rc_schedule restart [32m[SYSTEM]/usr/bin/killall -14 access_logd[0m killall: access_logd: no process killed [ fw_wan_L3 - 78 ] : wan1-ip0.0.0 enter [ fw_wan_L3 - 78 ] : wan2-ip0.0.0 enter [ fw_wan_L3 - 78 ] : wan3-ip0.0.0 enter [ firewall_main - 136 ] : end fw_exe [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: Bad rule (does a matching rule exist in that chain?). [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. [libiptc/libiptc.c::iptc_commit():2608] out_free_newcounters iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. rcd: [run] deQ =/usr/sbin/rc_app/rc_wan restart [ wan_main - 651 ] : rc wan enter [ wan_action - 425 ] : entering wan0 InternetGatewayDevice.WANDevice.1.WANConnectionDevice. [ wan_stop_con - 193 ] : entering wan1 [ipv6/common.c::ip6_config_dump():171] lan_ifname = <group1> [ipv6/common.c::ip6_config_dump():172] wan_ifname = <eth2.2> [ipv6/common.c::ip6_config_dump():173] wan_l2_ifname = <eth2.2> [ipv6/common.c::ip6_config_dump():174] wan_ppp_ifname = <ppp6> [ipv6/common.c::ip6_config_dump():175] wan_mode = 0 [ipv6/common.c::ip6_config_dump():176] lan_mode = 2 [ipv6/common.c::ip6_config_dump():177] dhcp_account = <> [ipv6/common.c::ip6_config_dump():178] dhcp_domain = <> [ipv6/common.c::ip6_config_dump():179] pppoe_username = <> [ipv6/common.c::ip6_config_dump():180] pppoe_passwd = <> [ipv6/common.c::ip6_config_dump():181] pppoe_service = <> [ipv6/common.c::ip6_config_dump():182] custom_relay_router = 0 [ipv6/common.c::ip6_config_dump():183] relay_router = <> [ipv6/common.c::ip6_config_dump():184] fixed_wan_ipaddr = <> [ipv6/common.c::ip6_config_dump():185] fixed_gw_ipaddr = <> [ipv6/common.c::ip6_config_dump():186] fixed_wan_plen = 0 [ipv6/common.c::ip6_config_dump():187] fixed_lan_ipaddr = <> [ipv6/common.c::ip6_config_dump():188] fixed_lan_plen = 0 [ipv6/common.c::ip6_config_dump():189] fixed_dns1 = <> [ipv6/common.c::ip6_config_dump():190] fixed_dns2 = <> [ipv6/common.c::ip6_config_dump():191] custom_ifid_enable = 0 [ipv6/common.c::ip6_config_dump():194] ifid = <0000:0000:0000:0000> [ipv6/common.c::ip6_config_dump():195] ipv6ipv4ppp_one_session = 0 [ipv6/common.c::ip6_config_dump():196] ipv6_ppp_stateless = 0 [ipv6/common.c::ip6_config_dump():197] ipv6_dhcpc_no_na = 0 [ipv6/common.c::ip6_config_dump():199] ip4_MaskLen = 0 [ipv6/common.c::ip6_config_dump():200] ip6_6rdPrefixLen = 0 [ipv6/common.c::ip6_config_dump():202] ip6_6rdPrefix = :: [ipv6/common.c::ip6_config_dump():221] No ip6_6rdBRIP4Addr. [ipv6/common.c::ip6_config_dump():224] conf->wan_use_fixed_dns = 0 [ipv6/common.c::ip6_config_dump():225] conf->wan_use_fixed_dns_server1 = <> [ipv6/common.c::ip6_config_dump():226] conf->wan_use_fixed_dns_server2 = <> config parser successfully . [ wan_stop_con - 209 ] : allWanL3 of TotalCon <> [ stop_L2 - 989 ] : entering wan1 [ wan_stop_con - 261 ] : stop l2 +++++++++++++++ [ wan_stop_con - 193 ] : entering wan2 [ wan_stop_con - 209 ] : allWanL3 of TotalCon <> [ stop_L2 - 989 ] : entering wan2 [ wan_stop_con - 261 ] : stop l2 +++++++++++++++ [ wan_stop_con - 193 ] : entering wan3 [ wan_stop_con - 209 ] : allWanL3 of TotalCon <> [ stop_L2 - 989 ] : entering wan3 [ wan_stop_con - 261 ] : stop l2 +++++++++++++++ [ wan_main - 973 ] : ======vpi=<0>,vci=<0>,enable=<0>,encap=<(null)> [ wan_main - 974 ] : mode=<(null)>,link_enable=<(null)>contype=<0> [ wan_action - 425 ] : entering wan0 InternetGatewayDevice.WANDevice.1.WANConnectionDevice. [ wan_action - 440 ] : entering wan0 wan_start_con [ wan_start_con - 275 ] : entering wan1 [ is_wan_enable - 107 ] : wan 1 is enabled for ANNEXB [ start_L2 - 906 ] : entering <wan 1> Ethernet [ start_eth - 665 ] : entering start_eth [32m[SYSTEM]/sbin/ifconfig eth2.2 up[0m [32m[SYSTEM]/sbin/ifconfig eth2.2 down[0m [32m[SYSTEM]/sbin/ifconfig eth2.2 hw ether 8C:3B:AD:ea:7b:3c [0m [32m[SYSTEM]/sbin/ifconfig eth2.2 up[0m [32m[SYSTEM]/sbin/ifconfig eth2.2 mtu 1500[0m [32m[SYSTEM]ifconfig eth2.2 up [0m [ start_eth - 671 ] : L3IfName: eth2.2 [ wan_start_con - 305 ] : ###########enter bridge mode########## [ start_bridge - 31 ] : entering wan1 [32m[SYSTEM]/sbin/brctl addif group1 eth2.2[0m [32m[SYSTEM]/bin/killall -SIGUSR1 udhcpc_1[0m [ wan_start_con - 377 ] : ipv6 restart <disable> [ wan_start_con - 382 ] : ipv6 restart, v4 mode bridge v6 mode disable [32m[SYSTEM]/usr/sbin/rc_app/rc_ipv6 restart[0m [32m[SYSTEM]/bin/echo 0 > /proc/sys/net/ipv6/conf/all/forwarding[0m [32m[SYSTEM]/usr/bin/killall dhcp6c[0m killall: dhcp6c: no process killed [32m[SYSTEM]/bin/killall pppd_ip6[0m killall: pppd_ip6: no process killed [32m[SYSTEM]/usr/bin/killall radvd[0m killall: radvd: no process killed [32m[SYSTEM]/usr/bin/killall -9 dhcp6s[0m killall: dhcp6s: no process killed [32m[SYSTEM]/bin/killall -9 totd[0m killall: totd: no process killed [32m[SYSTEM]ip6tables -t filter -F[0m [32m[SYSTEM]ip6tables -t mangle -F[0m [32m[SYSTEM]ip6tables -t raw -F[0m [32m[SYSTEM]ip6tables -t filter -X[0m [32m[SYSTEM]ip6tables -t mangle -X[0m [32m[SYSTEM]ip6tables -t raw -X[0m [32m[SYSTEM]ip6tables -t filter -P INPUT ACCEPT[0m [32m[SYSTEM]ip6tables -t filter -P FORWARD ACCEPT[0m [32m[SYSTEM]ip6tables -C /tmp/rules6[0m ip6tables v1.4.10: option `-C' requires an argument Try `ip6tables -h' or 'ip6tables --help' for more information. [32m[SYSTEM]killall mld[0m killall: mld: no process killed [32m[SYSTEM]/sbin/ip -6 route flush dev tun6to4[0m Cannot find device "tun6to4" [32m[SYSTEM]/sbin/ip link set dev tun6to4 down[0m Cannot find device "tun6to4" [32m[SYSTEM]/sbin/ip tunnel del tun6to4[0m delete tunnel "tun6to4" failed: No such device [32m[SYSTEM]/sbin/Ip -6 route flush dev tun6rd[0m Cannot find device "tun6rd" [32m[SYSTEM]/sbin/Ip link set dev tun6rd down[0m Cannot find device "tun6rd" [32m[SYSTEM]/sbin/Ip tunnel del tun6rd[0m delete tunnel "tun6rd" failed: No such device [32m[SYSTEM]/sbin/rmmod ipv6_br.ko[0m rmmod: ipv6_br.ko: No such file or directory sh: /sbin/fc: not found [32m[SYSTEM]/usr/bin/killall dhcp6c[0m killall: dhcp6c: no process killed [32m[SYSTEM]/usr/bin/killall ip6_autod[0m killall: ip6_autod: no process killed [32m[SYSTEM]/bin/rm -f /var/ip6prefix*[0m [ipv6/ipv6.c::stop_ipv6():74] stop ip6 wan mode: (-1) [32m[SYSTEM]/bin/ip -6 route del default[0m RTNETLINK answers: No such file or directory [32m[SYSTEM]/bin/ip -6 route del default[0m RTNETLINK answers: No such file or directory [32m[SYSTEM]/bin/ip -6 route del default[0m RTNETLINK answers: No such file or directory [32m[SYSTEM]/bin/ip -6 route del default[0m RTNETLINK answers: No such file or directory [32m[SYSTEM]/bin/ip -6 route del default[0m RTNETLINK answers: No such file or directory [32m[SYSTEM]/bin/ip -6 route del default[0m RTNETLINK answers: No such file or directory [32m[SYSTEM]/bin/echo 1 > /proc/sys/net/ipv6/conf/all/disable_ipv6[0m [ipv6/ipv6.c::start_ipv6():106] AP Mode no need ipv6. [32m[SYSTEM]/usr/sbin/rc_app/rc_hw_nat start[0m [32m[SYSTEM]/bin/rmmod hw_nat[0m rmmod: hw_nat: No such file or directory [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [scvlan.c::get_vlan_group():50] enable:1, type:0, group name:Bridge, vid=0, pri=0, ports=00000000 [ wan_action - 440 ] : entering wan0 wan_start_con [ wan_start_con - 275 ] : entering wan2 [ is_wan_enable - 102 ] : wan 2 is not enable [ wan_start_con - 285 ] : wan 2 is disabled [ wan_action - 440 ] : entering wan0 wan_start_con [ wan_start_con - 275 ] : entering wan3 [ is_wan_enable - 102 ] : wan 3 is not enable [ wan_start_con - 285 ] : wan 3 is disabled rcd: [run] deQ =/usr/sbin/rc_app/rc_schedule restart [flash.c::sc_get_region():632] Original Region Data: 00, 0a [32m[SYSTEM]/bin/cp /usr/etc/crontab /etc/crontab[0m set crontab for wifi_schedule --- 0 [32m[SYSTEM]/bin/echo GMT-10 > /etc/TZ[0m [32m[SYSTEM]echo 1 > /proc/net/ipt_condition/schedule [0m sh: cannot create /proc/net/ipt_condition/schedule: nonexistent directory PATH=/sbin:/bin:/usr/sbin:/usr/bin::/usr/local/sbin:/var/sbin ap1: dhcpc FAIL /etc/udhcpc.ap.script: line 94: /etc/dhclient-exit-hook.in: not found


OpenWrt bootlog

[03060C0E][03060D0A] DDR Calibration DQS reg = 0000887E U-Boot 1.1.3 (Oct 31 2017 - 12:57:49) Bord: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83f70000 flash manufacture id: c2, device id 20 17 find flash: MX25L6405D *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 5.0.0.0 -------------------------------------------- ASIC 7628_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Oct 31 2017 Time:12:57:49 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes RESET MT7628 PHY!!!!!! Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. default: 3 0 *************************************************** Sercomm Boot Version 4.1.1.0 *************************************************** Entering Firmware : Everything is OK. Enter NMRP_main 0x0000: 8c 3b ad ea 7b 3b Trying Eth0 (10/100-M) Waitting for RX_DMA_BUSY status Start... done ETH_STATE_ACTIVE!! NMRP_FLASH_SIZE_buffer --> 82000000. NMRP:LISTENING ### No NMRP Server found ### TFTP Recovery Flag is 0xff 3: System Boot system code via Flash. ## Booting image at bc090000 ... Image Name: MIPS OpenWrt Linux-5.4.42 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1926862 Bytes = 1.8 MB Load Address: 80000000 Entry Point: 80000000 Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... [ 0.000000] Linux version 5.4.42 (evan@debian-d430) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13401+1-f8b4aa5062)) #0 Sat May 30 07:54:28 2020 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: MediaTek MT7628AN ver:1 eco:2 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019655 (MIPS 24KEc) [ 0.000000] MIPS: machine is Netgear R6020 (AC750) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000000] Writing ErrCtl register=0003cf08 [ 0.000000] Readback ErrCtl register=0003cf08 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 57644K/65536K available (4547K kernel code, 197K rwdata, 1024K rodata, 1200K init, 197K bss, 7892K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] intc: using register map from devicetree [ 0.000000] random: get_random_bytes called from start_kernel+0x32c/0x518 with crng_init=0 [ 0.000000] CPU Clock: 580MHz [ 0.000000] timer_probe: no matching timers found [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns [ 0.000011] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns [ 0.015370] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048) [ 0.059449] pid_max: default: 32768 minimum: 301 [ 0.068770] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.083104] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.104534] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.123739] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.137270] pinctrl core: initialized pinctrl subsystem [ 0.148656] NET: Registered protocol family 16 [ 0.266562] mt7620-pci 10140000.pcie: Port 0 N_FTS = 1b105000 [ 0.427401] PCI host bridge /pcie@10140000 ranges: [ 0.436742] MEM 0x0000000020000000..0x000000002fffffff [ 0.447053] IO 0x0000000010160000..0x000000001016ffff [ 0.481010] PCI host bridge to bus 0000:00 [ 0.489058] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] [ 0.502567] pci_bus 0000:00: root bus resource [io 0xffffffff] [ 0.514263] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.527678] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.543390] pci 0000:00:00.0: [14c3:0801] type 01 class 0x060400 [ 0.555229] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 0.567589] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 0.580050] pci 0000:00:00.0: supports D1 [ 0.587879] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.600813] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.616762] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000 [ 0.628596] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 0.641975] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.655288] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.668779] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.681764] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 0.694836] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 0.707878] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 0.721639] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff] [ 0.735053] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref] [ 0.749329] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] [ 0.762757] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit] [ 0.777212] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref] [ 0.791468] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.801276] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff] [ 0.814689] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref] [ 0.832833] clocksource: Switched to clocksource MIPS [ 0.844144] NET: Registered protocol family 2 [ 0.853654] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.870127] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.885210] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.899135] TCP: Hash tables configured (established 1024 bind 1024) [ 0.911840] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.924681] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.938765] NET: Registered protocol family 1 [ 0.947354] PCI: CLS 0 bytes, default 32 [ 0.959655] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 0.980671] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.992123] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 1.028199] mt7621_gpio 10000600.gpio: registering 32 gpios [ 1.039461] mt7621_gpio 10000600.gpio: registering 32 gpios [ 1.050658] mt7621_gpio 10000600.gpio: registering 32 gpios [ 1.061929] Serial: 8250/16550 driver, 3 ports, IRQ sharing disabled [ 1.075588] printk: console [ttyS0] disabled [ 1.084019] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 28, base_baud = 2500000) is a 16550A [ 1.101818] printk: console [ttyS0] enabled [ 1.101818] printk: console [ttyS0] enabled [ 1.118297] printk: bootconsole [early0] disabled [ 1.118297] printk: bootconsole [early0] disabled [ 1.138199] spi-mt7621 10000b00.spi: sys_freq: 193333333 [ 1.156014] spi-nor spi0.0: mx25l6405d (8192 Kbytes) [ 1.165969] 5 fixed-partitions partitions found on MTD device spi0.0 [ 1.178556] Creating 5 MTD partitions on "spi0.0": [ 1.188054] 0x000000000000-0x000000040000 : "u-boot" [ 1.198923] 0x000000040000-0x000000060000 : "factory" [ 1.209977] 0x000000060000-0x000000090000 : "nvram" [ 1.220742] 0x000000090000-0x000000780000 : "firmware" [ 1.235346] 2 uimage-fw partitions found on MTD device firmware [ 1.247141] Creating 2 MTD partitions on "firmware": [ 1.256991] 0x000000000000-0x0000001e0000 : "kernel" [ 1.267849] 0x0000001e0000-0x0000006f0000 : "rootfs" [ 1.278657] mtd: device 5 (rootfs) set to be root filesystem [ 1.291633] 1 squashfs-split partitions found on MTD device rootfs [ 1.303960] 0x000000570000-0x0000006f0000 : "rootfs_data" [ 1.315720] 0x000000780000-0x000000800000 : "reserved" [ 1.327730] libphy: Fixed MDIO Bus: probed [ 1.347871] rt3050-esw 10110000.esw: link changed 0x00 [ 1.360058] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 1.378485] NET: Registered protocol family 10 [ 1.391826] Segment Routing with IPv6 [ 1.399293] NET: Registered protocol family 17 [ 1.408173] 8021q: 802.1Q VLAN Support v1.8 [ 1.427884] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 1.448668] Freeing unused kernel memory: 1200K [ 1.457656] This architecture does not have kernel memory protection. [ 1.470405] Run /sbin/init as init process [ 1.732830] random: fast init done [ 2.392020] init: Console is alive [ 2.399167] init: - watchdog - [ 3.746938] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 3.944147] usbcore: registered new interface driver usbfs [ 3.955184] usbcore: registered new interface driver hub [ 3.965845] usbcore: registered new device driver usb [ 3.983009] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 3.997842] ehci-fsl: Freescale EHCI Host controller driver [ 4.010650] ehci-platform: EHCI generic platform driver [ 4.031356] phy phy-10120000.usbphy.0: remote usb device wakeup disabled [ 4.044636] phy phy-10120000.usbphy.0: UTMI 16bit 30MHz [ 4.054988] ehci-platform 101c0000.ehci: EHCI Host Controller [ 4.066432] ehci-platform 101c0000.ehci: new USB bus registered, assigned bus number 1 [ 4.082233] ehci-platform 101c0000.ehci: irq 26, io mem 0x101c0000 [ 4.108843] ehci-platform 101c0000.ehci: USB 2.0 started, EHCI 1.00 [ 4.122307] hub 1-0:1.0: USB hub found [ 4.130238] hub 1-0:1.0: 1 port detected [ 4.143655] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 4.157743] ohci-platform: OHCI generic platform driver [ 4.168433] ohci-platform 101c1000.ohci: Generic Platform OHCI controller [ 4.181940] ohci-platform 101c1000.ohci: new USB bus registered, assigned bus number 2 [ 4.197720] ohci-platform 101c1000.ohci: irq 26, io mem 0x101c1000 [ 4.273868] hub 2-0:1.0: USB hub found [ 4.281800] hub 2-0:1.0: 1 port detected [ 4.295211] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.320098] init: - preinit - [ 5.921322] random: jshn: uninitialized urandom read (4 bytes read) [ 6.096486] random: jshn: uninitialized urandom read (4 bytes read) [ 6.320670] random: jshn: uninitialized urandom read (4 bytes read) [ 6.877522] rt3050-esw 10110000.esw: link changed 0x00 [ 6.944092] urandom_read: 2 callbacks suppressed [ 6.944102] random: procd: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 10.946850] rt3050-esw 10110000.esw: link changed 0x08 [ 11.225714] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 11.269710] urandom-seed: Seed file not found (/etc/urandom.seed) [ 11.384762] procd: - early - [ 11.390763] procd: - watchdog - [ 12.122247] procd: - watchdog - [ 12.128953] procd: - ubus - [ 12.171645] random: ubusd: uninitialized urandom read (4 bytes read) [ 12.185703] random: ubusd: uninitialized urandom read (4 bytes read) [ 12.198944] random: ubusd: uninitialized urandom read (4 bytes read) [ 12.213046] procd: - init - Please press Enter to activate this console. [ 13.007186] kmodloader: loading kernel modules from /etc/modules.d/* [ 13.066618] Loading modules backported from Linux version v5.7-rc3-0-g6a8b55ed4056 [ 13.081691] Backport generated by backports.git v5.7-rc3-1-0-gc0c7d2bb [ 13.175616] xt_time: kernel timezone is -0000 [ 13.408333] mt76_wmac 10300000.wmac: ASIC revision: 76280001 [ 13.564425] urngd: v1.0.2 started. [ 13.771114] random: crng init done [ 13.777871] random: 1 urandom warning(s) missed due to ratelimiting [ 14.471216] mt76_wmac 10300000.wmac: Firmware Version: 20151201 [ 14.483023] mt76_wmac 10300000.wmac: Build Time: 20151201183641 [ 14.520840] mt76_wmac 10300000.wmac: firmware init done [ 14.746899] mt76x2e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4 [ 14.759462] mt76x2e 0000:01:00.0: ASIC revision: 76120044 [ 15.881060] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a [ 15.914597] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00 [ 15.925512] mt76x2e 0000:01:00.0: Build: 1 [ 15.933625] mt76x2e 0000:01:00.0: Build Time: 201507311614____ [ 15.977477] mt76x2e 0000:01:00.0: Firmware running! [ 16.043978] PPP generic driver version 2.4.2 [ 16.062071] NET: Registered protocol family 24 [ 16.109560] kmodloader: done loading kernel modules from /etc/modules.d/* [ 31.773336] rt3050-esw 10110000.esw: link changed 0x00 [ 35.250489] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 35.276874] jffs2_build_filesystem(): unlocking the mtd device... [ 35.276883] done. [ 35.292936] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 35.940569] rt3050-esw 10110000.esw: link changed 0x08 [ 38.414576] br-lan: port 1(eth0.1) entered blocking state [ 38.425353] br-lan: port 1(eth0.1) entered disabled state [ 38.436474] device eth0.1 entered promiscuous mode [ 38.446020] device eth0 entered promiscuous mode [ 38.594844] br-lan: port 1(eth0.1) entered blocking state [ 38.605605] br-lan: port 1(eth0.1) entered forwarding state [ 39.401375] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 47.252737] done. [ 47.256613] jffs2: notice: (1295) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 47.501612] overlayfs: upper fs does not support tmpfile.


Notes

Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
inbox/toh/netgear/netgear_r6020.txt · Last modified: 2020/07/11 07:07 by tmomas