Meraki MX65

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

A Cisco cloud based firewall with 250 Mbps throughput, small form factor fan less design the case is made from aluminium. 10 LAN ports including 2 POE+ ports. There are two variants of this device, the MX65 and MX65W, the latter of which features two unsupported Broadcom wireless BCM43520KMLG chips but otherwise exactly the same hardware. As a result the MX65W can only be supported to the same extent as the MX65.

Not supported.

Describe if there are any ongoing activities that might lead to OpenWrt support.

CPU CPU MHz Ram Flash Network WLAN USB Serial JTag
Broadcom BCM58625BBOKF12G StrataGX™ 1200 2 GB 1 GB 12x 10/100/1000 None 1x 2.0 Yes ?
Architecture Arm cortex a9
Vendor Cisco Meraki
Bootloader U-Boot
System-On-Chip Broadcom StrataGX™ Communications Processor
CPU/Speed 1.2 GHz
Flash-Chip Micron MT29F8G08ABACA
Flash size 1 GB
RAM 2 GB (4 x 4Gb H5TC4G83CFR)
Wireless N/A
Ethernet 12x 10/100/1000 Mbit/s w/ vlan support 2 x PoE
Switch 1x BCM58625 (2 Ports) & 2x QCA8337-AL3C 5x G2PM109RN LF 1524F
PoE BCM59111KMLG (2 Ports connected on QCA8337 switch 2)
USB 1x 2.0
Serial YES - on board header
JTAG Yes - not populated
# cat /proc/mtd
dev: size erasesize name
mtd0: 00100000 00040000 “boot”
mtd1: 00080000 00040000 “shmoo”
mtd2: 00300000 00040000 “bootkernel1”
mtd3: 00100000 00040000 “nvram”
mtd4: 00300000 00040000 “bootkernel2”
mtd5: 3f700000 00040000 “ubi”
mtd6: 40000000 00040000 “all”

  • Remove 4 rubber feet on underside of the case.
  • Remove 4 hidden screws from under rubber feet.
  • Lift off black underside. Slide out PCB

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

Set of 4 pins labeled J5

  • Pin 1 - (has a small triangle symbol under it) furthest from the onboard USB socket (3.3v) DO NOT CONNECT to anything
  • Pin 2 - connected to RX on my USB adapter
  • Pin 3 - connected to TX on my USB adapter
  • Pin 4 - (closest to USB socket) connected to Ground on my USB adapter
Serial connection parameters
for Meraki MX65
115200, 8N1

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:

un-populated port J8

20 Pin JTAG port

root@OpenWrt:~# dmesg [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.42 (root@cluster5) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13346-69f8983af4)) #0 SMP Sun May 24 12:44:00 2020 [ 0.000000] CPU: ARMv7 Processor [413fc090] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache [ 0.000000] OF: fdt: Machine model: Cisco Meraki MX65 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Hit pending asynchronous external abort (FSR=0x00001c06) during first unmask, this is most likely caused by a firmware/bootloader bug. [ 0.000000] On node 0 totalpages: 524288 [ 0.000000] Normal zone: 4608 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 524288 pages, LIFO batch:63 [ 0.000000] percpu: Embedded 14 pages/cpu s28108 r8192 d21044 u57344 [ 0.000000] pcpu-alloc: s28108 r8192 d21044 u57344 alloc=14*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 519680 [ 0.000000] Kernel command line: console=ttyS0,115200n8 earlyprintk [ 0.000000] Dentry cache hash table entries: 262144 (order: 8, 1048576 bytes, linear) [ 0.000000] Inode-cache hash table entries: 131072 (order: 7, 524288 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 2068248K/2097152K available (5370K kernel code, 184K rwdata, 1376K rodata, 1024K init, 338K bss, 28904K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] L2C-310 enabling early BRESP for Cortex-A9 [ 0.000000] L2C-310 full line of zeros enabled for Cortex-A9 [ 0.000000] L2C-310 ID prefetch enabled, offset 1 lines [ 0.000000] L2C-310 dynamic clock gating enabled, standby mode enabled [ 0.000000] L2C-310 Coherent cache controller enabled, 16 ways, 512 kB [ 0.000000] L2C-310 Coherent: CACHE_ID 0x410000c8, AUX_CTRL 0x7e150001 [ 0.000000] random: get_random_bytes called from start_kernel+0x2e0/0x490 with crng_init=0 [ 0.000006] sched_clock: 64 bits at 600MHz, resolution 1ns, wraps every 2199023255551ns [ 0.000020] clocksource: arm_global_timer: mask: 0xffffffffffffffff max_cycles: 0x8a60dddf76, max_idle_ns: 440795229572 ns [ 0.000037] Switching to timer-based delay loop, resolution 1ns [ 0.000173] clocksource: arm,sp804: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 15290083572 ns [ 0.000301] Calibrating delay loop (skipped), value calculated using timer frequency.. 1200.00 BogoMIPS (lpj=6000000) [ 0.000310] pid_max: default: 32768 minimum: 301 [ 0.000415] Mount-cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000424] Mountpoint-cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000917] CPU: Testing write buffer coherency: ok [ 0.000937] CPU0: Spectre v2: using BPIALL workaround [ 0.001102] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.001413] Setting up static identity map for 0x60100000 - 0x60100060 [ 0.001496] rcu: Hierarchical SRCU implementation. [ 0.001682] smp: Bringing up secondary CPUs ... [ 0.002180] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.002185] CPU1: Spectre v2: using BPIALL workaround [ 0.002267] smp: Brought up 1 node, 2 CPUs [ 0.002273] SMP: Total of 2 processors activated (2400.00 BogoMIPS). [ 0.002278] CPU: All CPU(s) started in SVC mode. [ 0.004753] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4 [ 0.004902] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.004915] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.005040] pinctrl core: initialized pinctrl subsystem [ 0.005472] NET: Registered protocol family 16 [ 0.006328] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.006823] No ATAGs? [ 0.006929] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers. [ 0.006938] hw-breakpoint: maximum watchpoint size is 4 bytes. [ 0.019442] cryptd: max_cpu_qlen set to 1000 [ 0.023180] SCSI subsystem initialized [ 0.024091] clocksource: Switched to clocksource arm_global_timer [ 0.024721] thermal_sys: Registered thermal governor 'step_wise' [ 0.025042] NET: Registered protocol family 2 [ 0.025381] tcp_listen_portaddr_hash hash table entries: 1024 (order: 1, 12288 bytes, linear) [ 0.025411] TCP established hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.025505] TCP bind hash table entries: 16384 (order: 5, 131072 bytes, linear) [ 0.025667] TCP: Hash tables configured (established 16384 bind 16384) [ 0.025751] UDP hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.025819] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes, linear) [ 0.026015] NET: Registered protocol family 1 [ 0.026042] PCI: CLS 0 bytes, default 64 [ 0.026461] hw perfevents: enabled with armv7_cortex_a9 PMU driver, 7 counters available [ 0.029894] workingset: timestamp_bits=14 max_order=19 bucket_order=5 [ 0.034345] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.034356] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.058857] io scheduler mq-deadline registered [ 0.058866] io scheduler kyber registered [ 0.058998] io scheduler bfq registered [ 0.060456] dma-pl330 18020000.dma: Loaded driver for PL330 DMAC-241330 [ 0.060469] dma-pl330 18020000.dma: DBUFF-1024x8bytes Num_Chans-8 Num_Peri-1 Num_Events-16 [ 0.060698] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.061201] printk: console [ttyS0] disabled [ 0.061247] 18000300.serial: ttyS0 at MMIO 0x18000300 (irq = 22, base_baud = 3906250) is a 16550A [ 0.572494] printk: console [ttyS0] enabled [ 0.577648] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xd3 [ 0.584021] nand: Micron MT29F8G08ABACAWP [ 0.588054] nand: 1024 MiB, SLC, erase size: 256 KiB, page size: 4096, OOB size: 224 [ 0.595835] iproc_nand 18026000.nand: detected 1024MiB total, 256KiB blocks, 4KiB pages, 27B OOB, 8-bit, BCH-24 (1KiB sector) [ 0.607840] Bad block table found at page 262080, version 0x01 [ 0.614299] Bad block table found at page 262016, version 0x01 [ 0.620835] 6 fixed-partitions partitions found on MTD device brcmnand.0 [ 0.627563] Creating 6 MTD partitions on "brcmnand.0": [ 0.632715] 0x000000000000-0x000000080000 : "U-boot" [ 0.638284] 0x000000080000-0x000000100000 : "Shmoo" [ 0.643757] 0x000000100000-0x000000400000 : "bootkernel1" [ 0.649756] 0x000000400000-0x000000500000 : "senao_nvram" [ 0.655736] 0x000000500000-0x000000800000 : "bootkernel2" [ 0.661675] 0x000000800000-0x00003ff00000 : "ubi" [ 0.668278] libphy: iProc MDIO bus: probed [ 0.672389] iproc-mdio 18032000.mdio: Broadcom iProc MDIO bus at 0x(ptrval) [ 0.679574] libphy: mdio_mux: probed [ 0.683219] libphy: mdio_mux: probed [ 0.686923] libphy: mdio_mux: probed [ 0.710533] libphy: mdio_mux: probed [ 0.734444] libphy: Fixed MDIO Bus: probed [ 0.749082] b53-srab-switch 18036000.srab: SerDes lane 0, model: 1, rev B0 (OUI: 0x0143bff0) [ 0.757554] b53-srab-switch 18036000.srab: Port 5 mode: sgmii [ 0.764181] b53-srab-switch 18036000.srab: SerDes lane 1, model: 1, rev B0 (OUI: 0x0143bff0) [ 0.772638] b53-srab-switch 18036000.srab: Port 4 mode: sgmii [ 0.778427] b53_common: found switch: BCM585xx/586xx/88312, rev 0 [ 0.784721] bgmac-enet 18024000.ethernet: MAC address not present in device tree [ 0.792159] bgmac-enet 18024000.ethernet: Invalid MAC addr: 00:00:00:00:00:00 [ 0.799322] bgmac-enet 18024000.ethernet: Using random MAC: 4e:e1:5d:a4:7d:a9 [ 0.807310] bcm-iproc-i2c 18038000.i2c: bus set to 100000 Hz [ 0.813850] at24 0-0050: 8192 byte 24c64 EEPROM, writable, 32 bytes/write [ 0.821183] sp805-wdt 18039000.watchdog: registration successful [ 0.828138] NET: Registered protocol family 10 [ 0.833217] Segment Routing with IPv6 [ 0.836959] NET: Registered protocol family 17 [ 0.841509] 8021q: 802.1Q VLAN Support v1.8 [ 0.845766] Registering SWP/SWPB emulation handler [ 0.863228] b53-srab-switch 18036000.srab: SerDes lane 0, model: 1, rev B0 (OUI: 0x0143bff0) [ 0.871811] b53-srab-switch 18036000.srab: Port 5 mode: sgmii [ 0.878540] b53-srab-switch 18036000.srab: SerDes lane 1, model: 1, rev B0 (OUI: 0x0143bff0) [ 0.887017] b53-srab-switch 18036000.srab: Port 4 mode: sgmii [ 0.892790] b53_common: found switch: BCM585xx/586xx/88312, rev 0 [ 0.985803] libphy: dsa slave smi: probed [ 0.990242] b53-srab-switch 18036000.srab wan1 (uninitialized): PHY [dsa-0.0:00] driver [Generic PHY] [ 1.000310] b53-srab-switch 18036000.srab wan2 (uninitialized): PHY [dsa-0.0:01] driver [Generic PHY] [ 1.010845] b53-srab-switch 18036000.srab: Using legacy PHYLIB callbacks. Please migrate to PHYLINK! [ 1.020295] DSA: tree 0 setup [ 1.392101] qca8k 1.0:10: Using legacy PHYLIB callbacks. Please migrate to PHYLINK! [ 1.438128] qca8k 1.0:10 lan8 (uninitialized): PHY [1.0:00] driver [Generic PHY] [ 1.452090] qca8k 1.0:10 lan9 (uninitialized): PHY [1.0:01] driver [Generic PHY] [ 1.466020] qca8k 1.0:10 lan10 (uninitialized): PHY [1.0:02] driver [Generic PHY] [ 1.480029] qca8k 1.0:10 lan11 (uninitialized): PHY [1.0:03] driver [Generic PHY] [ 1.494052] qca8k 1.0:10 lan12 (uninitialized): PHY [1.0:04] driver [Generic PHY] [ 1.520062] DSA: tree 1 setup [ 1.892099] qca8k 1.2000:10: Using legacy PHYLIB callbacks. Please migrate to PHYLINK! [ 1.938127] qca8k 1.2000:10 lan3 (uninitialized): PHY [1.2000:00] driver [Generic PHY] [ 1.952591] qca8k 1.2000:10 lan4 (uninitialized): PHY [1.2000:01] driver [Generic PHY] [ 1.966130] qca8k 1.2000:10 lan5 (uninitialized): PHY [1.2000:02] driver [Generic PHY] [ 1.980597] qca8k 1.2000:10 lan6 (uninitialized): PHY [1.2000:03] driver [Generic PHY] [ 1.994086] qca8k 1.2000:10 lan7 (uninitialized): PHY [1.2000:04] driver [Generic PHY] [ 2.020135] DSA: tree 2 setup [ 2.023939] UBI: auto-attach mtd5 [ 2.027277] ubi0: attaching mtd5 [ 2.047279] random: fast init done [ 3.064236] random: crng init done [ 7.055164] ubi0: scanning is finished [ 7.070391] ubi0: attached mtd5 (name "ubi", size 1015 MiB) [ 7.075994] ubi0: PEB size: 262144 bytes (256 KiB), LEB size: 253952 bytes [ 7.082881] ubi0: min./max. I/O unit sizes: 4096/4096, sub-page size 4096 [ 7.089684] ubi0: VID header offset: 4096 (aligned 4096), data offset: 8192 [ 7.096664] ubi0: good PEBs: 4060, bad PEBs: 0, corrupted PEBs: 0 [ 7.102770] ubi0: user volume: 7, internal volumes: 1, max. volumes count: 128 [ 7.110008] ubi0: max/mean erase counter: 81/76, WL threshold: 4096, image sequence number: 887924684 [ 7.119251] ubi0: available PEBs: 0, total reserved PEBs: 4060, PEBs reserved for bad PEB handling: 80 [ 7.128590] ubi0: background thread "ubi_bgt0d" started, PID 666 [ 7.135847] block ubiblock0_0: created from ubi0:0(rootfs) [ 7.141347] ubiblock: device ubiblock0_0 (rootfs) set to be root filesystem [ 7.151370] VFS: Mounted root (squashfs filesystem) readonly on device 254:0. [ 7.159213] Freeing unused kernel memory: 1024K [ 7.204203] Run /sbin/init as init process [ 7.468682] init: Console is alive [ 7.472202] init: - watchdog - [ 7.844522] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 7.877862] usbcore: registered new interface driver usbfs [ 7.883402] usbcore: registered new interface driver hub [ 7.888801] usbcore: registered new device driver usb [ 7.920914] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 7.929438] ehci-fsl: Freescale EHCI Host controller driver [ 7.935624] ehci-platform: EHCI generic platform driver [ 7.940982] ehci-platform 1802a000.usb: EHCI Host Controller [ 7.946720] ehci-platform 1802a000.usb: new USB bus registered, assigned bus number 1 [ 7.954723] ehci-platform 1802a000.usb: irq 74, io mem 0x1802a000 [ 7.984116] ehci-platform 1802a000.usb: USB 2.0 started, EHCI 1.00 [ 7.991143] hub 1-0:1.0: USB hub found [ 7.994944] hub 1-0:1.0: 2 ports detected [ 8.001191] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 8.007936] ohci-platform: OHCI generic platform driver [ 8.013295] ohci-platform 1802b000.usb: Generic Platform OHCI controller [ 8.020046] ohci-platform 1802b000.usb: new USB bus registered, assigned bus number 2 [ 8.027954] ohci-platform 1802b000.usb: irq 74, io mem 0x1802b000 [ 8.109098] hub 2-0:1.0: USB hub found [ 8.112968] hub 2-0:1.0: 2 ports detected [ 8.120346] usbcore: registered new interface driver usb-storage [ 8.126515] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 8.144285] init: - preinit - [ 8.364106] usb 1-2: new high-speed USB device number 2 using ehci-platform [ 8.567264] usb-storage 1-2:1.0: USB Mass Storage device detected [ 8.573777] scsi host0: usb-storage 1-2:1.0 [ 9.624405] scsi 0:0:0:0: Direct-Access Kingston DataTraveler G3 1.00 PQ: 0 ANSI: 4 [ 9.633872] sd 0:0:0:0: [sda] 31246288 512-byte logical blocks: (16.0 GB/14.9 GiB) [ 9.642109] sd 0:0:0:0: [sda] Write Protect is off [ 9.646923] sd 0:0:0:0: [sda] Mode Sense: 45 00 00 00 [ 9.647483] sd 0:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 9.697876] sda: sda1 [ 9.702372] sd 0:0:0:0: [sda] Attached SCSI removable disk [ 13.025370] mount_root: loading kmods from internal overlay [ 13.039039] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 13.046502] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 23.838060] UBIFS (ubi0:6): Mounting in unauthenticated mode [ 23.843824] UBIFS (ubi0:6): background thread "ubifs_bgt0_6" started, PID 832 [ 24.044729] UBIFS (ubi0:6): UBIFS: mounted UBI device 0, volume 6, name "rootfs_data" [ 24.052586] UBIFS (ubi0:6): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes [ 24.062540] UBIFS (ubi0:6): FS size: 387530752 bytes (369 MiB, 1526 LEBs), journal size 19300352 bytes (18 MiB, 76 LEBs) [ 24.073440] UBIFS (ubi0:6): reserved for root: 4952683 bytes (4836 KiB) [ 24.080079] UBIFS (ubi0:6): media format: w4/r0 (latest is w5/r0), UUID ACD90B91-5240-4533-9312-6C1C247EA3DA, small LPT model [ 24.092817] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 24.099879] block: unable to load configuration (fstab: Entry not found) [ 24.106653] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab [ 24.113146] block: unable to load configuration (fstab: Entry not found) [ 24.119917] block: attempting to load /etc/config/fstab [ 24.125832] block: unable to load configuration (fstab: Entry not found) [ 24.132571] block: no usable configuration [ 24.140695] UBIFS (ubi0:6): un-mount UBI device 0 [ 24.145443] UBIFS (ubi0:6): background thread "ubifs_bgt0_6" stops [ 24.155189] UBIFS (ubi0:6): Mounting in unauthenticated mode [ 24.160932] UBIFS (ubi0:6): background thread "ubifs_bgt0_6" started, PID 835 [ 24.361549] UBIFS (ubi0:6): UBIFS: mounted UBI device 0, volume 6, name "rootfs_data" [ 24.369415] UBIFS (ubi0:6): LEB size: 253952 bytes (248 KiB), min./max. I/O unit sizes: 4096 bytes/4096 bytes [ 24.379356] UBIFS (ubi0:6): FS size: 387530752 bytes (369 MiB, 1526 LEBs), journal size 19300352 bytes (18 MiB, 76 LEBs) [ 24.390256] UBIFS (ubi0:6): reserved for root: 4952683 bytes (4836 KiB) [ 24.396888] UBIFS (ubi0:6): media format: w4/r0 (latest is w5/r0), UUID ACD90B91-5240-4533-9312-6C1C247EA3DA, small LPT model [ 24.724326] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 24.731366] block: unable to load configuration (fstab: Entry not found) [ 24.738133] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab [ 24.744658] block: unable to load configuration (fstab: Entry not found) [ 24.751403] block: attempting to load /etc/config/fstab [ 24.756692] block: unable to load configuration (fstab: Entry not found) [ 24.763431] block: no usable configuration [ 24.768114] mount_root: overlay filesystem has not been fully initialized yet [ 24.776141] mount_root: switching to ubifs overlay [ 24.788559] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off. [ 24.852286] urandom-seed: Seed file not found (/etc/urandom.seed) [ 24.910610] procd: - early - [ 24.913537] procd: - watchdog - [ 25.454288] procd: - watchdog - [ 25.457599] procd: - ubus - [ 25.613686] procd: - init - [ 25.916747] kmodloader: loading kernel modules from /etc/modules.d/* [ 25.931461] urngd: v1.0.2 started. [ 25.940710] tun: Universal TUN/TAP device driver, 1.6 [ 25.974307] i2c /dev entries driver [ 25.982252] fuse: init (API version 7.31) [ 26.009374] xt_time: kernel timezone is -0000 [ 26.025604] PPP generic driver version 2.4.2 [ 26.030767] NET: Registered protocol family 24 [ 26.040768] kmodloader: done loading kernel modules from /etc/modules.d/* [ 30.501468] bgmac-enet 18024000.ethernet eth0: Link is Up - 1Gbps/Full - flow control off [ 30.511181] b53-srab-switch 18036000.srab sw0: configuring for fixed/ link mode [ 30.518652] 8021q: adding VLAN 0 to HW filter on device sw0 [ 30.524628] b53-srab-switch 18036000.srab sw0: Link is Up - 1Gbps/Full - flow control off [ 30.614247] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 30.620719] IPv6: ADDRCONF(NETDEV_CHANGE): sw0: link becomes ready [ 30.627588] device sw0 entered promiscuous mode [ 30.632153] device eth0 entered promiscuous mode [ 30.654232] qca8k 1.2000:10 lan3: configuring for phy/ link mode [ 30.662625] br-lan: port 1(lan3) entered blocking state [ 30.667980] br-lan: port 1(lan3) entered disabled state [ 30.693793] device lan3 entered promiscuous mode [ 30.738506] qca8k 1.2000:10 lan4: configuring for phy/ link mode [ 30.747339] br-lan: port 2(lan4) entered blocking state [ 30.752615] br-lan: port 2(lan4) entered disabled state [ 30.791352] device lan4 entered promiscuous mode [ 30.833658] qca8k 1.2000:10 lan5: configuring for phy/ link mode [ 30.842094] br-lan: port 3(lan5) entered blocking state [ 30.847379] br-lan: port 3(lan5) entered disabled state [ 30.917271] device lan5 entered promiscuous mode [ 30.958128] qca8k 1.2000:10 lan6: configuring for phy/ link mode [ 30.966724] br-lan: port 4(lan6) entered blocking state [ 30.972006] br-lan: port 4(lan6) entered disabled state [ 31.040141] device lan6 entered promiscuous mode [ 31.081795] qca8k 1.2000:10 lan7: configuring for phy/ link mode [ 31.090262] br-lan: port 5(lan7) entered blocking state [ 31.095570] br-lan: port 5(lan7) entered disabled state [ 31.161704] device lan7 entered promiscuous mode [ 31.188769] b53-srab-switch 18036000.srab sw1: configuring for fixed/ link mode [ 31.196271] 8021q: adding VLAN 0 to HW filter on device sw1 [ 31.201997] b53-srab-switch 18036000.srab sw1: Link is Up - 1Gbps/Full - flow control off [ 31.287483] IPv6: ADDRCONF(NETDEV_CHANGE): sw1: link becomes ready [ 31.304268] device sw1 entered promiscuous mode [ 31.328129] qca8k 1.0:10 lan8: configuring for phy/ link mode [ 31.347236] br-lan: port 6(lan8) entered blocking state [ 31.352498] br-lan: port 6(lan8) entered disabled state [ 31.394160] device lan8 entered promiscuous mode [ 31.436183] qca8k 1.0:10 lan9: configuring for phy/ link mode [ 31.444525] br-lan: port 7(lan9) entered blocking state [ 31.449790] br-lan: port 7(lan9) entered disabled state [ 31.514142] device lan9 entered promiscuous mode [ 31.556155] qca8k 1.0:10 lan10: configuring for phy/ link mode [ 31.564403] br-lan: port 8(lan10) entered blocking state [ 31.569735] br-lan: port 8(lan10) entered disabled state [ 31.616230] device lan10 entered promiscuous mode [ 31.677196] qca8k 1.0:10 lan11: configuring for phy/ link mode [ 31.685394] br-lan: port 9(lan11) entered blocking state [ 31.690723] br-lan: port 9(lan11) entered disabled state [ 31.756209] device lan11 entered promiscuous mode [ 31.813387] qca8k 1.0:10 lan12: configuring for phy/ link mode [ 31.827289] br-lan: port 10(lan12) entered blocking state [ 31.832746] br-lan: port 10(lan12) entered disabled state [ 31.904157] device lan12 entered promiscuous mode [ 31.911906] qca8k 1.0:10 lan12: Link is Up - 1Gbps/Full - flow control rx/tx [ 31.940295] br-lan: port 10(lan12) entered blocking state [ 31.945748] br-lan: port 10(lan12) entered forwarding state [ 31.953588] b53-srab-switch 18036000.srab wan1: configuring for phy/gmii link mode [ 31.962747] 8021q: adding VLAN 0 to HW filter on device wan1 [ 31.964875] b53-srab-switch 18036000.srab wan1: Link is Up - 1Gbps/Full - flow control off [ 32.070205] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 32.077092] br-wan: port 1(wan1) entered blocking state [ 32.082330] br-wan: port 1(wan1) entered disabled state [ 32.087830] device wan1 entered promiscuous mode [ 32.114425] br-wan: port 1(wan1) entered blocking state [ 32.119700] br-wan: port 1(wan1) entered forwarding state [ 32.130322] b53-srab-switch 18036000.srab wan2: configuring for phy/gmii link mode [ 32.138670] 8021q: adding VLAN 0 to HW filter on device wan2 [ 32.234501] br-wan: port 2(wan2) entered blocking state [ 32.239743] br-wan: port 2(wan2) entered disabled state [ 32.245279] device wan2 entered promiscuous mode root@OpenWrt:~#


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/03/17 12:45
  • by clayface