Meraki MR52

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

Describe if there are any ongoing activities that might lead to OpenWrt support.

Architecture Arm v7
Vendor Cisco Meraki
Bootloader U-Boot
System-On-Chip IPQ8068
CPU/Speed 1.4 GHz
Flash size 128 MB
RAM 512MB
Wireless 2x QCA9994, 1x QCA9889
Ethernet 2x AR8033 (1x PoE input)
Serial Yes - not populated
JTAG Yes - not populated
dev: size erasesize name
mtd0: 00040000 00020000 “sbl1”
mtd1: 00140000 00020000 “mibib”
mtd2: 00140000 00020000 “sbl2”
mtd3: 00280000 00020000 “sbl3”
mtd4: 00120000 00020000 “ddrconfig”
mtd5: 00120000 00020000 “ssd”
mtd6: 00280000 00020000 “tz”
mtd7: 00280000 00020000 “rpm”
mtd8: 00180000 00020000 “u-boot”
mtd9: 00a80000 00020000 “bootkernel1”
mtd10: 00a80000 00020000 “bootkernel2”
mtd11: 046c0000 00020000 “ubi”
mtd12: 00200000 00020000 “art”

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

  • Pin 1 - (has a small triangle symbol under it). Do not use.
  • Pin 2 - RX
  • Pin 3 - TX
  • Pin 4 - GND
Serial connection parameters 115200, 8N1

U-Boot 2012.07-gd040ed5-dirty [local,local] (Mar 29 2016 - 07:59:21) DRAM: 235 MiB cdp: machid 4971 NAND: 128 MiB Using default environment In: serial Out: serial Err: serial late_init: machid 4971 Net: No ethernet found. NAND read: device 0 offset 0x2c40000, size 0xa80000 11010048 bytes read: OK bootm 0x42000000#config@2## Booting kernel from FIT Image at 42000000 ... Using 'config@2' configuration Trying 'kernel-1' kernel subimage Description: ARM OpenWrt Linux-5.10.39 Type: Kernel Image Compression: gzip compressed Data Start: 0x420000e4 Data Size: 4223148 Bytes = 4 MiB Architecture: ARM OS: Linux Load Address: 0x44208000 Entry Point: 0x44208000 Hash algo: crc32 Hash value: 524f4670 Hash algo: sha1 Hash value: 2bce581ee2ffe108de396f961ebf7c4104ad74b4 Verifying Hash Integrity ... crc32+ sha1+ OK ## Flattened Device Tree from FIT Image at 42000000 Using 'config@2' configuration Trying 'fdt-1' FDT blob subimage Description: ARM OpenWrt meraki_mr52 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x424072c8 Data Size: 30742 Bytes = 30 KiB Architecture: ARM Hash algo: crc32 Hash value: 314fcd8c Hash algo: sha1 Hash value: b601b770c045a22c28dbd685b28eb9e755906228 Verifying Hash Integrity ... crc32+ sha1+ OK Booting using the fdt blob at 0x424072c8 Uncompressing Kernel Image ... OK Loading Device Tree to 4eaf5000, end 4eaff815 ... OK Using machid 0x136b from environment Starting kernel ... [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.10.39 (root@cluster5) (arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 8.4.0 r16808-d346dba6a5) 8.4.0, GNU l1 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Meraki MR52 [ 0.000000] OF: fdt: Ignoring memory range 0x41500000 - 0x44000000 [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000044000000-0x000000005fefffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000044000000-0x000000005fefffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000044000000-0x000000005fefffff] [ 0.000000] percpu: Embedded 15 pages/cpu s30732 r8192 d22516 u61440 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 113426 [ 0.000000] Kernel command line: loader=u-boot part=bootkernel2 console=ttyMSM0,115200n8 ubi.mtd=ubi ubi.mtd=art [ 0.000000] Bootloader command line not present [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 441932K/457728K available (6554K kernel code, 608K rwdata, 1648K rodata, 1024K init, 236K bss, 15796K reserved, 0K ) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] random: get_random_bytes called from start_kernel+0x3ac/0x558 with crng_init=0 [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns [ 0.000010] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns [ 0.000032] Switching to timer-based delay loop, resolution 160ns [ 0.000300] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) [ 0.000331] pid_max: default: 32768 minimum: 301 [ 0.000516] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.000540] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001632] CPU: Testing write buffer coherency: ok [ 0.001925] qcom_scm: convention: smc legacy [ 0.002894] Setting up static identity map for 0x44300000 - 0x44300060 [ 0.003081] rcu: Hierarchical SRCU implementation. [ 0.003376] dyndbg: Ignore empty _ddebug table in a CONFIG_DYNAMIC_DEBUG_CORE build [ 0.003623] smp: Bringing up secondary CPUs ... [ 0.005626] smp: Brought up 1 node, 2 CPUs [ 0.005648] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.005665] CPU: All CPU(s) started in SVC mode. [ 0.017697] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 0.017873] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.017908] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.018064] pinctrl core: initialized pinctrl subsystem [ 0.019330] NET: Registered protocol family 16 [ 0.019703] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.021198] thermal_sys: Registered thermal governor 'step_wise' [ 0.023264] cpuidle: using governor ladder [ 0.023344] cpuidle: using governor menu [ 0.067652] usbcore: registered new interface driver usbfs [ 0.067740] usbcore: registered new interface driver hub [ 0.067812] usbcore: registered new device driver usb [ 0.067888] pps_core: LinuxPPS API ver. 1 registered [ 0.067906] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> [ 0.067946] PTP clock support registered [ 0.070112] clocksource: Switched to clocksource dg_timer [ 0.071189] NET: Registered protocol family 2 [ 0.071363] IP idents hash table entries: 8192 (order: 4, 65536 bytes, linear) [ 0.072144] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.072207] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.072253] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.072315] TCP: Hash tables configured (established 4096 bind 4096) [ 0.072521] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.072563] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.072878] NET: Registered protocol family 1 [ 0.072938] PCI: CLS 0 bytes, default 64 [ 0.074445] workingset: timestamp_bits=14 max_order=17 bucket_order=3 [ 0.080122] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.080145] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.187863] qcom-pcie 1b500000.pci: supply vdda not found, using dummy regulator [ 0.188134] qcom-pcie 1b500000.pci: supply vdda_phy not found, using dummy regulator [ 0.188259] qcom-pcie 1b500000.pci: supply vdda_refclk not found, using dummy regulator [ 0.188569] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges: [ 0.188671] qcom-pcie 1b500000.pci: IO 0x000fe00000..0x000fe0ffff -> 0x000fe00000 [ 0.188722] qcom-pcie 1b500000.pci: MEM 0x0008000000..0x000fdfffff -> 0x0008000000 [ 0.416061] qcom-pcie 1b500000.pci: Link up [ 0.416243] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.416271] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.416296] pci_bus 0000:00: root bus resource [io 0x0000-0xffff] (bus address [0xfe00000-0xfe0ffff]) [ 0.416317] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.416406] pci 0000:00:00.0: [17cb:0101] type 01 class 0x060400 [ 0.416569] pci 0000:00:00.0: supports D1 [ 0.416590] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.420774] PCI: bus0: Fast back to back transfers disabled [ 0.421310] pci 0000:01:00.0: [168c:0050] type 00 class 0x028000 [ 0.421631] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.422134] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.423134] pci 0000:01:00.0: supports D1 [ 0.423154] pci 0000:01:00.0: PME# supported from D0 D1 D3hot [ 0.427599] PCI: bus1: Fast back to back transfers disabled [ 0.427703] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x082fffff] [ 0.427733] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x081fffff 64bit] [ 0.427897] pci 0000:01:00.0: BAR 6: assigned [mem 0x08200000-0x0820ffff pref] [ 0.427922] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.427952] pci 0000:00:00.0: bridge window [mem 0x08000000-0x082fffff] [ 0.428006] pci 0000:00:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128 [ 0.428224] pci 0000:01:00.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128 [ 0.429198] pcieport 0000:00:00.0: AER: enabled with IRQ 44 [ 0.430305] qcom-pcie 1b700000.pci: supply vdda not found, using dummy regulator [ 0.430581] qcom-pcie 1b700000.pci: supply vdda_phy not found, using dummy regulator [ 0.430716] qcom-pcie 1b700000.pci: supply vdda_refclk not found, using dummy regulator [ 0.431000] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges: [ 0.431081] qcom-pcie 1b700000.pci: IO 0x0031e00000..0x0031e0ffff -> 0x0031e00000 [ 0.431126] qcom-pcie 1b700000.pci: MEM 0x002e000000..0x0031dfffff -> 0x002e000000 [ 0.656860] qcom-pcie 1b700000.pci: Link up [ 0.657024] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.657052] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.657075] pci_bus 0001:00: root bus resource [io 0x10000-0x1ffff] (bus address [0x31e00000-0x31e0ffff]) [ 0.657096] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.657174] pci 0001:00:00.0: [17cb:0101] type 01 class 0x060400 [ 0.657316] pci 0001:00:00.0: supports D1 [ 0.657336] pci 0001:00:00.0: PME# supported from D0 D1 D3hot [ 0.661449] PCI: bus0: Fast back to back transfers disabled [ 0.661963] pci 0001:01:00.0: [168c:0046] type 00 class 0x028000 [ 0.662257] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.663635] pci 0001:01:00.0: PME# supported from D0 D3hot D3cold [ 0.668057] PCI: bus1: Fast back to back transfers disabled [ 0.668154] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] [ 0.668182] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.668333] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.668360] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 0.668405] pci 0001:00:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128 [ 0.668611] pci 0001:01:00.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128 [ 0.669485] pcieport 0001:00:00.0: AER: enabled with IRQ 46 [ 0.670575] qcom-pcie 1b900000.pci: supply vdda not found, using dummy regulator [ 0.670806] qcom-pcie 1b900000.pci: supply vdda_phy not found, using dummy regulator [ 0.670937] qcom-pcie 1b900000.pci: supply vdda_refclk not found, using dummy regulator [ 0.671225] qcom-pcie 1b900000.pci: host bridge /soc/pci@1b900000 ranges: [ 0.671305] qcom-pcie 1b900000.pci: IO 0x0035e00000..0x0035e0ffff -> 0x0035e00000 [ 0.671354] qcom-pcie 1b900000.pci: MEM 0x0032000000..0x0035dfffff -> 0x0032000000 [ 0.896876] qcom-pcie 1b900000.pci: Link up [ 0.897041] qcom-pcie 1b900000.pci: PCI host bridge to bus 0002:00 [ 0.897071] pci_bus 0002:00: root bus resource [bus 00-ff] [ 0.897096] pci_bus 0002:00: root bus resource [io 0x20000-0x2ffff] (bus address [0x35e00000-0x35e0ffff]) [ 0.897116] pci_bus 0002:00: root bus resource [mem 0x32000000-0x35dfffff] [ 0.897195] pci 0002:00:00.0: [17cb:0101] type 01 class 0x060400 [ 0.897341] pci 0002:00:00.0: supports D1 [ 0.897360] pci 0002:00:00.0: PME# supported from D0 D1 D3hot [ 0.901501] PCI: bus0: Fast back to back transfers disabled [ 0.902022] pci 0002:01:00.0: [168c:0046] type 00 class 0x028000 [ 0.902319] pci 0002:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.903700] pci 0002:01:00.0: PME# supported from D0 D3hot D3cold [ 0.908134] PCI: bus1: Fast back to back transfers disabled [ 0.908232] pci 0002:00:00.0: BAR 8: assigned [mem 0x32000000-0x321fffff] [ 0.908261] pci 0002:01:00.0: BAR 0: assigned [mem 0x32000000-0x321fffff 64bit] [ 0.908412] pci 0002:00:00.0: PCI bridge to [bus 01-ff] [ 0.908438] pci 0002:00:00.0: bridge window [mem 0x32000000-0x321fffff] [ 0.908483] pci 0002:00:00.0: Max Payload Size set to 128/ 128 (was 128), Max Read Rq 128 [ 0.908689] pci 0002:01:00.0: Max Payload Size set to 128/ 256 (was 128), Max Read Rq 128 [ 0.909568] pcieport 0002:00:00.0: AER: enabled with IRQ 48 [ 0.912823] L2 @ QSB rate. Forcing new rate. [ 0.913050] L2 @ 384000 KHz [ 0.913249] CPU0 @ 800000 KHz [ 0.913268] CPU1 @ QSB rate. Forcing new rate. [ 0.913405] CPU1 @ 384000 KHz [ 0.917775] gsbi 12440000.gsbi: GSBI port protocol: 4 crci: 0 [ 0.919796] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 0.921636] gsbi 16600000.gsbi: GSBI port protocol: 2 crci: 0 [ 0.923893] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.924868] msm_serial 12450000.serial: msm_serial: detected port #1 [ 0.924926] msm_serial 12450000.serial: uartclk = 25000000 [ 0.925009] 12450000.serial: ttyMSM1 at MMIO 0x12450000 (irq = 49, base_baud = 1562500) is a MSM [ 0.925504] msm_serial 16340000.serial: msm_serial: detected port #0 [ 0.925556] msm_serial 16340000.serial: uartclk = 7372800 [ 0.925626] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 50, base_baud = 460800) is a MSM [ 0.925665] msm_serial: console setup on port #0 [ 2.009738] printk: console [ttyMSM0] enabled [ 2.015039] msm_serial: driver initialized [ 2.024580] loop: module loaded [ 2.026289] nand: device found, Manufacturer ID: 0x01, Chip ID: 0xa1 [ 2.026542] nand: AMD/Spansion S34MS01G2 [ 2.033254] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.037202] 13 fixed-partitions partitions found on MTD device qcom_nand.0 [ 2.044517] Creating 13 MTD partitions on "qcom_nand.0": [ 2.051380] 0x000000000000-0x000000040000 : "sbl1" [ 2.057847] 0x000000040000-0x000000180000 : "mibib" [ 2.064064] 0x000000180000-0x0000002c0000 : "sbl2" [ 2.068775] 0x0000002c0000-0x000000540000 : "sbl3" [ 2.071824] random: fast init done [ 2.079758] 0x000000540000-0x000000660000 : "ddrconfig" [ 2.082648] 0x000000660000-0x000000780000 : "ssd" [ 2.087317] 0x000000780000-0x000000a00000 : "tz" [ 2.094981] 0x000000a00000-0x000000c80000 : "rpm" [ 2.100782] 0x000001fc0000-0x000002140000 : "u-boot" [ 2.104532] 0x0000021c0000-0x000002c40000 : "bootkernel1" [ 2.126149] 0x000002c40000-0x0000036c0000 : "bootkernel2" [ 2.147114] 0x0000036c0000-0x000007d80000 : "ubi" [ 2.283220] 0x000007d80000-0x000007f80000 : "art" [ 2.300105] libphy: Fixed MDIO Bus: probed [ 2.301985] libphy: GPIO Bitbanged MDIO: probed [ 2.503946] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found [ 2.504014] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found [ 2.510628] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock [ 2.517493] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37 [ 2.523190] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000 [ 2.530575] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported [ 2.536310] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported [ 2.544132] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2 [ 2.552006] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported [ 2.557746] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported [ 2.565237] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors [ 2.571965] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors [ 2.579449] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled [ 2.586557] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 2.592755] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address 4e:ff:18:9a:50:68 [ 2.642717] libphy: stmmac: probed [ 2.645533] ipq806x-gmac-dwmac 37600000.ethernet: IRQ eth_wake_irq not found [ 2.645595] ipq806x-gmac-dwmac 37600000.ethernet: IRQ eth_lpi not found [ 2.652909] ipq806x-gmac-dwmac 37600000.ethernet: PTP uses main clock [ 2.659070] ipq806x-gmac-dwmac 37600000.ethernet: User ID: 0x10, Synopsys ID: 0x37 [ 2.665361] ipq806x-gmac-dwmac 37600000.ethernet: DWMAC1000 [ 2.672797] ipq806x-gmac-dwmac 37600000.ethernet: DMA HW capability register supported [ 2.678464] ipq806x-gmac-dwmac 37600000.ethernet: RX Checksum Offload Engine supported [ 2.686275] ipq806x-gmac-dwmac 37600000.ethernet: COE Type 2 [ 2.694179] ipq806x-gmac-dwmac 37600000.ethernet: TX Checksum insertion supported [ 2.699900] ipq806x-gmac-dwmac 37600000.ethernet: Wake-Up On Lan supported [ 2.707370] ipq806x-gmac-dwmac 37600000.ethernet: Enhanced/Alternate descriptors [ 2.714139] ipq806x-gmac-dwmac 37600000.ethernet: Enabled extended descriptors [ 2.721700] ipq806x-gmac-dwmac 37600000.ethernet: Ring mode enabled [ 2.728633] ipq806x-gmac-dwmac 37600000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 2.734897] ipq806x-gmac-dwmac 37600000.ethernet: device MAC address 2a:53:72:6c:ef:b2 [ 2.784986] libphy: stmmac: probed [ 2.788068] i2c /dev entries driver [ 2.788777] i2c_qup 16680000.i2c: using default clock-frequency 100000 [ 2.799235] sdhci: Secure Digital Host Controller Interface driver [ 2.799289] sdhci: Copyright(c) Pierre Ossman [ 2.804501] sdhci-pltfm: SDHCI platform and OF driver helper [ 2.812845] NET: Registered protocol family 10 [ 2.816919] Segment Routing with IPv6 [ 2.818898] NET: Registered protocol family 17 [ 2.823402] 8021q: 802.1Q VLAN Support v1.8 [ 2.826973] Registering SWP/SWPB emulation handler [ 2.869480] qcom_rpm 108000.rpm: RPM firmware 3.0.16777342 [ 2.886783] s1a: Bringing 0uV into 1050000-1050000uV [ 2.887232] s1a: supplied by regulator-dummy [ 2.891165] s1b: Bringing 0uV into 1050000-1050000uV [ 2.895455] s1b: supplied by regulator-dummy [ 2.900235] s2a: Bringing 0uV into 800000-800000uV [ 2.904726] s2a: supplied by regulator-dummy [ 2.909092] s2b: Bringing 0uV into 800000-800000uV [ 2.913793] s2b: supplied by regulator-dummy [ 2.920453] thermal thermal_zone0: failed to read out thermal zone (-110) [ 2.940708] ubi0: attaching mtd11 [ 3.078297] random: crng init done [ 3.576355] ubi0: scanning is finished [ 3.587728] ubi0: attached mtd11 (name "ubi", size 70 MiB) [ 3.587753] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.592160] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.598958] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.605870] ubi0: good PEBs: 564, bad PEBs: 2, corrupted PEBs: 0 [ 3.612659] ubi0: user volume: 6, internal volumes: 1, max. volumes count: 128 [ 3.618836] ubi0: max/mean erase counter: 752/313, WL threshold: 4096, image sequence number: 1338979908 [ 3.625931] ubi0: available PEBs: 0, total reserved PEBs: 564, PEBs reserved for bad PEB handling: 18 [ 3.635630] ubi1: attaching mtd12 [ 3.635757] ubi0: background thread "ubi_bgt0d" started, PID 138 [ 3.644726] ubi1: MTD device 12 is write-protected, attach in read-only mode [ 3.670982] ubi1: scanning is finished [ 3.681020] ubi1 warning: ubi_eba_init: cannot reserve enough PEBs for bad PEB handling, reserved 2, need 20 [ 3.681539] ubi1: attached mtd12 (name "art", size 2 MiB) [ 3.689904] ubi1: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 3.695296] ubi1: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 3.702025] ubi1: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 3.708836] ubi1: good PEBs: 16, bad PEBs: 0, corrupted PEBs: 0 [ 3.715682] ubi1: user volume: 1, internal volumes: 1, max. volumes count: 128 [ 3.721587] ubi1: max/mean erase counter: 2/1, WL threshold: 4096, image sequence number: 438719976 [ 3.728801] ubi1: available PEBs: 0, total reserved PEBs: 16, PEBs reserved for bad PEB handling: 2 [ 3.738437] ubi1: background thread "ubi_bgt1d" started, PID 139 [ 3.748168] block ubiblock0_2: created from ubi0:2(rootfs) [ [ 3.770093] Freeing unused kernel memory: 1024K [ 3.810904] Run /sbin/init as init process [ 4.394333] init: Console is alive [ 4.394499] init: - watchdog - [ 5.066068] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 5.232961] genirq: irq_chip msmgpio did not update eff. affinity mask of irq 52 [ 5.236648] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 5.247080] init: - preinit - get_mac_binary: file /sys/bus/i2c/devices/0-0052/eeprom not found! [ 6.080699] ipq806x-gmac-dwmac 37600000.ethernet eth1: PHY [gpio-0:04] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) [ 6.082617] dwmac1000: Master AXI performs any burst length [ 6.090832] ipq806x-gmac-dwmac 37600000.ethernet eth1: No Safety Features support found [ 6.096054] ipq806x-gmac-dwmac 37600000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 6.104451] ipq806x-gmac-dwmac 37600000.ethernet eth1: registered PTP clock [ 6.114811] ipq806x-gmac-dwmac 37600000.ethernet eth1: configuring for phy/sgmii link mode Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 9.354759] UBIFS (ubi0:5): Mounting in unauthenticated mode [ 9.355161] UBIFS (ubi0:5): background thread "ubifs_bgt0_5" started, PID 224 [ 9.410607] UBIFS (ubi0:5): recovery needed [ 9.538488] UBIFS (ubi0:5): recovery completed [ 9.538596] UBIFS (ubi0:5): UBIFS: mounted UBI device 0, volume 5, name "rootfs_data" [ 9.541927] UBIFS (ubi0:5): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 9.549732] UBIFS (ubi0:5): FS size: 10031104 bytes (9 MiB, 79 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) [ 9.559715] UBIFS (ubi0:5): reserved for root: 473793 bytes (462 KiB) [ 9.569948] UBIFS (ubi0:5): media format: w5/r0 (latest is w5/r0), UUID EB05CE7A-3ABF-4262-92C9-EFF60D80DB52, small LPT model [ 9.581767] mount_root: switching to ubifs overlay [ 9.603021] urandom-seed: Seeding with /etc/urandom.seed [ 9.794058] procd: - early - [ 9.794228] procd: - watchdog - [ 10.385830] procd: - watchdog - [ 10.548037] procd: - ubus - [ 10.624251] procd: - init - Please press Enter to activate this console. [ 11.069963] urngd: v1.0.2 started. [ 11.129235] kmodloader: loading kernel modules from /etc/modules.d/* [ 11.235251] at24 0-0052: supply vcc not found, using dummy regulator [ 11.236304] at24 0-0052: 8192 byte 24c64 EEPROM, writable, 32 bytes/write [ 11.241472] Loading modules backported from Linux version v5.10.34-0-g0aa66717f684 [ 11.247351] Backport generated by backports.git v5.10.34-1-0-g7b5533e1 [ 11.257961] ina2xx 0-0045: power monitor ina219 (Rshunt = 80000 uOhm) [ 11.270260] xt_time: kernel timezone is -0000 [ 11.323488] PPP generic driver version 2.4.2 [ 11.324425] NET: Registered protocol family 24 [ 11.356739] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x50. [ 11.357313] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142) [ 11.364173] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 12.301237] ath10k_pci 0000:01:00.0: qca9887 hw1.0 target 0x4100016d chip_id 0x004000ff sub 0000:0000 [ 12.301314] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 12.311119] ath10k_pci 0000:01:00.0: firmware ver 10.1-ct-87-__fW-022-ecad3248 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noa5 [ 12.382206] ath10k_pci 0000:01:00.0: board_file api 1 bmi_id N/A crc32 546cca0d [ 13.251269] ath10k_pci 0000:01:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256 [ 13.257863] ath10k_pci 0000:01:00.0: wmi print 'P 128 V 8 T 410' [ 13.257933] ath10k_pci 0000:01:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0' [ 13.264651] ath10k_pci 0000:01:00.0: wmi print 'alloc rem: 25560 iram: 24780' [ 13.309312] ath10k_pci 0000:01:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal file max-sta 128 raw 0 hwcrypto 1 [ 13.309735] ath10k_pci 0000:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000 [ 13.454452] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46. [ 13.456099] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 13.462283] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 14.568598] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 14.568699] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 14.582921] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-105 [ 16.931940] ath10k_pci 0001:01:00.0: board_file api 2 bmi_id 0:1 crc32 85498734 [ 20.480235] ath10k_pci 0001:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 20.480276] ath10k_pci 0001:01:00.0: msdu-desc: 2500 skid: 32 [ 20.562632] ath10k_pci 0001:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 20.563473] ath10k_pci 0001:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' [ 20.851980] ath10k_pci 0001:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 20.951020] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46. [ 20.952850] ath10k_pci 0002:01:00.0: enabling device (0140 -> 0142) [ 20.958743] ath10k_pci 0002:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 21.471095] ath10k_pci 0002:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 21.471144] ath10k_pci 0002:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 21.482955] ath10k_pci 0002:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-105 [ 23.801825] ath10k_pci 0002:01:00.0: board_file api 2 bmi_id 0:2 crc32 85498734 [ 27.348972] ath10k_pci 0002:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96 [ 27.349015] ath10k_pci 0002:01:00.0: msdu-desc: 2500 skid: 32 [ 27.431501] ath10k_pci 0002:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0' [ 27.432354] ath10k_pci 0002:01:00.0: wmi print 'free: 84920 iram: 13156 sram: 11224' [ 27.743522] ath10k_pci 0002:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1 [ 27.856768] kmodloader: done loading kernel modules from /etc/modules.d/* [ 31.818439] ipq806x-gmac-dwmac 37600000.ethernet eth1: PHY [gpio-0:04] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) [ 31.819302] dwmac1000: Master AXI performs any burst length [ 31.828543] ipq806x-gmac-dwmac 37600000.ethernet eth1: No Safety Features support found [ 31.833860] ipq806x-gmac-dwmac 37600000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 31.841997] ipq806x-gmac-dwmac 37600000.ethernet eth1: registered PTP clock [ 31.850887] ipq806x-gmac-dwmac 37600000.ethernet eth1: configuring for phy/sgmii link mode [ 31.862228] br-lan: port 1(eth1) entered blocking state [ 31.865987] br-lan: port 1(eth1) entered disabled state [ 31.871482] device eth1 entered promiscuous mode [ 31.970536] ipq806x-gmac-dwmac 37400000.ethernet eth0: PHY [gpio-0:00] driver [Qualcomm Atheros AR8031/AR8033] (irq=POLL) [ 31.971404] dwmac1000: Master AXI performs any burst length [ 31.980543] ipq806x-gmac-dwmac 37400000.ethernet eth0: No Safety Features support found [ 31.985858] ipq806x-gmac-dwmac 37400000.ethernet eth0: IEEE 1588-2008 Advanced Timestamp supported [ 31.994019] ipq806x-gmac-dwmac 37400000.ethernet eth0: registered PTP clock [ 32.030028] ipq806x-gmac-dwmac 37400000.ethernet eth0: configuring for phy/sgmii link mode [ 33.791739] ath10k_pci 0000:01:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256 [ 33.798294] ath10k_pci 0000:01:00.0: wmi print 'P 128 V 8 T 410' [ 33.798493] ath10k_pci 0000:01:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0' [ 33.804946] ath10k_pci 0000:01:00.0: wmi print 'alloc rem: 25560 iram: 24780' [ 33.849938] ath10k_pci 0000:01:00.0: pdev param 0 not supported by firmware [ 33.856183] ath10k_pci 0000:01:00.0: rts threshold -1 [ 33.865574] br-lan: port 2(wlan0) entered blocking state [ 33.865631] br-lan: port 2(wlan0) entered disabled state [ 33.870355] device wlan0 entered promiscuous mode [ 34.105372] ipq806x-gmac-dwmac 37400000.ethernet eth0: Link is Up - 1Gbps/Full - flow control rx/tx [ 34.105439] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 38.248420] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready [ 38.248840] br-lan: port 2(wlan0) entered blocking state [ 38.254311] br-lan: port 2(wlan0) entered forwarding state [ 38.260466] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready BusyBox v1.33.1 (2021-05-25 22:21:26 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r16808-d346dba6a5 ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/06/02 17:39
  • by clayface