Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision
Previous revision
Next revisionBoth sides next revision
inbox:toh:linksys:mr7350_1.0 [2023/03/29 01:27] – [Opening the case] whitsmeinbox:toh:linksys:mr7350_1.0 [2023/04/25 16:52] – [OpenWrt bootlog] soreau
Line 12: Line 12:
 /*****/ /*****/
  
-{{ media:example:genericrouter1.png?200|Generic Router}}+{{ media:linksys:mr7350_rear.png?200|Linksys MR7350}}
  
  
Line 43: Line 43:
 ===== Hardware highlights ===== ===== Hardware highlights =====
 ^ SoC                         ^ CPU MHz ^ Flash MB  ^ RAM MB ^ WLAN2.4 ^ WLAN5.0   ^ Gbit ports ^ USB      ^ Serial ^ JTag ^ ^ SoC                         ^ CPU MHz ^ Flash MB  ^ RAM MB ^ WLAN2.4 ^ WLAN5.0   ^ Gbit ports ^ USB      ^ Serial ^ JTag ^
-| Qualcomm Atheros IPQ6018LA  |  1800    256NAND  |  512    b/g/n  |  n/ac/ax  |  5          1x 3.0  |  Yes   |    |+| Qualcomm Atheros IPQ6018LA  |  1800    256NAND  |  512    b/g/n  |  n/ac/ax  |  5          1x 3.0  |  Yes   |  Yes   |
  
  
Line 111: Line 111:
 ===== Hardware ===== ===== Hardware =====
 ==== Info ==== ==== Info ====
-^ Architecture     EXAMPLE MIPS                             +^ Architecture     ARM                                      
-^ Vendor           EXAMPLE Ralink                           +^ Vendor           Linksys                                  
-^ Bootloader       EXAMPLE U-Boot                           | +^ Bootloader       | U-Boot                                   
-^ System-On-Chip   | EXAMPLE Ralink RT3052 - MIPS 24K V4.12   +^ CPU/Speed        | Qualcomm Atheros IPQ6000 1.2 GHz         
-^ CPU/Speed        | EXAMPLE 451 MHz                          +^ Flash-Chip       | unkown                           | 
-^ Flash-Chip       EXAMPLE unkown                           | +^ Flash size       256 MiB                                  
-^ Flash size       EXAMPLE 8 MiB                            +^ RAM              | 512 MiB                                  
-^ RAM              | EXAMPLE 64 MiB                           +^ Wireless         | 2.4G QCN5022 2x2, 5G QCN5052 2x2, 2.4G SKY85340-11, 5G SKY85755-11       | 
-^ Wireless         EXAMPLE RT2860v2 2.4GHz 802.11bgn        | +^ Bluetooth        | Antenna and radio present, but not activated 
-^ Ethernet         EXAMPLE 10/100 Mbit/s w/ vlan support    +^ Ethernet         | 10/100/1000 Mbit/s w/ vlan support    | 
-^ Switch           | EXAMPLE Qualcomm Atheros QCA8337         +^ USB              | 1x 3.0                                   
-^ USB              | EXAMPLE 1x 2.0                           +^ Serial           | [[#Serial|Yes -> baud rate 115200]]      
-^ Serial           EXAMPLE [[#Serial|Yes]]                  +^ JTAG             | [[#JTAG|Yes]]          |
-^ JTAG             EXAMPLE [[#JTAG|Not populated]]          |+
  
  
Line 143: Line 142:
 /* Thanks, your wiki administration - Oct. 2015 */ /* Thanks, your wiki administration - Oct. 2015 */
  
-**Insert photo of front of the casing**+{{ media:linksys:mr7350_front.png?400|Linksys MR7350 Front}}
  
-**Insert photo of back of the casing**+{{ media:linksys:mr7350_rear.png?400|Linksys MR7350 Rear}}
  
-**Insert photo of backside label**+{{ media:linksys:mr7350_bottom.png?400|Linksys MR7350 Bottom}}
  
-**Insert photo of PCB**+{{ media:linksys:mr7350_pcb_top.png?400|Linksys MR7350 PCB Top}} 
 + 
 +{{ media:linksys:mr7350_pcb_bottom.png?400|Linksys MR7350 PCB Bottom}}
  
 ==== Opening the case ==== ==== Opening the case ====
Line 164: Line 165:
  
 How to connect to the Serial Port of this specific device:\\ How to connect to the Serial Port of this specific device:\\
-**Insert photo of PCB with markings for serial port**+{{media:linksys:mr7350_serial.png?200|Linksys MR7350 Serial}}
  
-<WRAP BOX> +^ Serial connection parameters\\ for Linksys MR7350 1.0 | Baud Rate 115200, UART using FT232R to USB |
-FIXME //Replace EXAMPLE by real values.// +
-</WRAP> +
- +
-^ Serial connection parameters\\ for Linksys MR7350 1.0 | EXAMPLE 115200, 8N1 |+
  
 ==== JTAG ==== ==== JTAG ====
Line 179: Line 176:
  
 ===== Bootlogs ===== ===== Bootlogs =====
-==== OEM bootlog ====+==== OEM bootlog v1.1.7 ==== 
 +<WRAP bootlog>Format: Log Type - Time(microsec) - Message - Optional Info 
 +Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic 
 +S - QC_IMAGE_VERSION_STRING=BOOT.XF.0.3-00077-IPQ60xxLZB-2 
 +S - IMAGE_VARIANT_STRING=IPQ6018LA 
 +S - OEM_IMAGE_VERSION_STRING=crm-ubuntu64 
 +S - Boot Interface: NAND 
 +S - Secure Boot: Off 
 +S - Boot Config @ 0x000a602c = 0x000002e5 
 +S - JTAG ID @ 0x000a607c = 0x001390e1 
 +S - OEM ID @ 0x000a6080 = 0x00000000 
 +S - Serial Number @ 0x000a4128 = 0xfe655252 
 +S - OEM Config Row 0 @ 0x000a4188 = 0x0000000000000000 
 +S - OEM Config Row 1 @ 0x000a4190 = 0x0000000000000000 
 +S - Feature Config Row 0 @ 0x000a4130 = 0x0000800018200021 
 +S - Feature Config Row 1 @ 0x000a4138 = 0x02c3e83783000009 
 +S - PBL Patch Ver: 1 
 +S - I-cache: On 
 +S - D-cache: On 
 +B -      3413 - PBL, Start 
 +B -       592 - bootable_media_detect_entry, Start 
 +B -      4340 - bootable_media_detect_success, Start 
 +B -      5148 - elf_loader_entry, Start 
 +B -      5320 - auth_hash_seg_entry, Start 
 +B -      7787 - auth_hash_seg_exit, Start 
 +B -      8283 - elf_segs_hash_verify_entry, Start 
 +B -    110430 - elf_segs_hash_verify_exit, Start 
 +B -    114854 - auth_xbl_sec_hash_seg_entry, Start 
 +B -    114997 - auth_xbl_sec_hash_seg_exit, Start 
 +B -    121544 - xbl_sec_segs_hash_verify_entry, Start 
 +B -    121545 - xbl_sec_segs_hash_verify_exit, Start 
 +B -    122475 - PBL, End 
 +B -    103242 - SBL1, Start 
 +B -    243329 - GCC [RstStat:0x0, RstDbg:0x600000] WDog Stat : 0x4 
 +B -    245769 - clock_init, Start 
 +D -      2806 - clock_init, Delta 
 +B -    254339 - boot_flash_init, Start 
 +D -     26169 - boot_flash_init, Delta 
 +B -    283711 - sbl1_ddr_set_default_params, Start 
 +D -       244 - sbl1_ddr_set_default_params, Delta 
 +B -    290329 - boot_config_data_table_init, Start 
 +D -      4758 - boot_config_data_table_init, Delta - (575 Bytes) 
 +B -    300150 - CDT Version:2,Platform ID:8,Major ID:3,Minor ID:2,Subtype:
 +B -    305000 - Image Load, Start 
 +D -      6588 - OEM_MISC Image Loaded, Delta - (0 Bytes) 
 +B -    314333 - Image Load, Start 
 +D -      5063 - PMIC Image Loaded, Delta - (0 Bytes) 
 +B -    322202 - sbl1_ddr_set_params, Start 
 +B -    327173 - CPR configuration: 0x366 
 +B -    330376 - Pre_DDR_clock_init, Start 
 +D -       213 - Pre_DDR_clock_init, Delta 
 +D -         0 - sbl1_ddr_set_params, Delta 
 +B -    367037 - Image Load, Start 
 +D -       427 - APDP Image Loaded, Delta - (0 Bytes) 
 +B -    380121 - Image Load, Start 
 +D -       427 - QTI_MISC Image Loaded, Delta - (0 Bytes) 
 +B -    382561 - Image Load, Start 
 +D -       823 - Auth Metadata 
 +D -       732 - Segments hash check 
 +D -     22235 - QSEE Dev Config Image Loaded, Delta - (36354 Bytes) 
 +B -    406748 - Image Load, Start 
 +D -      6558 - Auth Metadata 
 +D -     10644 - Segments hash check 
 +D -    329186 - QSEE Image Loaded, Delta - (1470632 Bytes) 
 +B -    736392 - Image Load, Start 
 +D -       671 - Auth Metadata 
 +D -      1067 - Segments hash check 
 +D -     34587 - RPM Image Loaded, Delta - (102664 Bytes) 
 +B -    772687 - Image Load, Start 
 +D -       702 - Auth Metadata 
 +D -      3202 - Segments hash check 
 +D -    118828 - APPSBL Image Loaded, Delta - (561320 Bytes) 
 +B -    907131 - SBL1, End 
 +D -    804194 - SBL1, Delta 
 +S - Flash Throughput, 5000 KB/s  (2171545 Bytes,  422232 us) 
 +S - Core 0 Frequency, 800 MHz 
 +S - DDR Frequency, 466 MHz 
 +U-Boot 2016.01 (Mar 18 2020 - 13:15:21 +0800) 
 +CBT U-Boot ver: 2.3.01  ([IPQ6018].[SPF11.CSU1].[code version]) 
 +DRAM:  smem ram ptable found: ver: 2 len: 4 
 +512 MiB 
 +NAND:  ONFI device found 
 +ID = 1590aac2 
 +Vendor = c2 
 +Device = aa 
 +SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000 
 +ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 
 +256 MiB 
 +MMC:   sdhci: Node Not found, skipping initialization 
 +PCI0 is not defined in the device tree 
 +In:    serial@78B1000 
 +Out:   serial@78B1000 
 +Err:   serial@78B1000 
 +machid: 8030200 
 +eth0 MAC Address from ART is not valid 
 +eth1 MAC Address from ART is not valid 
 +eth2 MAC Address from ART is not valid 
 +eth3 MAC Address from ART is not valid 
 +eth4 MAC Address from ART is not valid 
 +eth5 MAC Address from ART is not valid 
 +Updating boot_count ... done 
 +Hit any key to stop autoboot:  1  0  
 +Setting bus to 0 
 +Valid chip addresses: 62 70 
 +NAND read: device 0 offset 0x6680000, size 0x800000 
 + 8388608 bytes read: OK 
 +## Loading kernel from FIT Image at 44000000 ... 
 +   Using 'config@1' configuration 
 +   Trying 'kernel@1' kernel subimage 
 +     Description:  ARM Linksys Linux-4.4.60 
 +     Type:         Kernel Image 
 +     Compression:  gzip compressed 
 +     Data Start:   0x440000e4 
 +     Data Size:    4712968 Bytes = 4.5 MiB 
 +     Architecture: ARM 
 +     OS:           Linux 
 +     Load Address: 0x41008000 
 +     Entry Point:  0x41008000 
 +     Hash algo:    crc32 
 +     Hash value:   4a216b6c 
 +     Hash algo:    sha1 
 +     Hash value:   2ee4bf63c32cb756c17d5cfdafb36fb1504568e3 
 +   Verifying Hash Integrity ... crc32+ sha1+ OK 
 +## Loading fdt from FIT Image at 44000000 ... 
 +   Using 'config@1' configuration 
 +   Trying 'fdt@1' fdt subimage 
 +     Description:  ARM Linksys Elise device tree blob 
 +     Type:         Flat Device Tree 
 +     Compression:  uncompressed 
 +     Data Start:   0x4447ec1c 
 +     Data Size:    73850 Bytes = 72.1 KiB 
 +     Architecture: ARM 
 +     Hash algo:    crc32 
 +     Hash value:   e7d6edd5 
 +     Hash algo:    sha1 
 +     Hash value:   54f4c5f01ed076d76b7f00a5968a664cf4eed54e 
 +   Verifying Hash Integrity ... crc32+ sha1+ OK 
 +   Booting using the fdt blob at 0x4447ec1c 
 +   Uncompressing Kernel Image ... OK 
 +   Loading Device Tree to 484ea000, end 484ff079 ... OK 
 +Could not find PCI in device tree 
 +Using machid 0x8030200 from environment 
 +Starting kernel ... 
 +[    0.000000] Booting Linux on physical CPU 0x0 
 +[    0.000000] Initializing cgroup subsys cpuset 
 +[    0.000000] Initializing cgroup subsys cpu 
 +[    0.000000] Initializing cgroup subsys cpuacct 
 +[    0.000000] Linux version 4.4.60 (root@build-vm) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r35193) ) #1 SMP PREEMPT Fri Dec 3 16:50:07 PST 2021 
 +[    0.000000] CPU: ARMv7 Processor [51af8014] revision 4 (ARMv7), cr=10c0383d 
 +[    0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache 
 +[    0.000000] Machine model: Qualcomm Technologies, Inc. IPQ6018/AP-CP03-C1 
 +[    0.000000] Ignoring memory range 0x40000000 - 0x41000000 
 +[    0.000000] Memory policy: Data cache writealloc 
 +[    0.000000] psci: probing for conduit method from DT. 
 +[    0.000000] psci: PSCIv1.0 detected in firmware. 
 +[    0.000000] psci: Using standard PSCI v0.2 function IDs 
 +[    0.000000] psci: MIGRATE_INFO_TYPE not supported. 
 +[    0.000000] PERCPU: Embedded 11 pages/cpu @9eb3a000 s15424 r8192 d21440 u45056 
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 109988 
 +[    0.000000] Kernel command line: init=/sbin/init rootfstype=squashfs ubi.mtd=alt_rootfs root=mtd:squashfs rootwait swiotlb=1 coherent_pool=2M 
 +[    0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) 
 +[    0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) 
 +[    0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) 
 +[    0.000000] Memory: 427400K/444416K available (7381K kernel code, 459K rwdata, 2184K rodata, 1024K init, 456K bss, 17016K reserved, 0K cma-reserved, 0K highmem) 
 +[    0.000000] Virtual kernel memory layout: 
 +[    0.000000]     vector  : 0xffff0000 - 0xffff1000     4 kB) 
 +[    0.000000]     fixmap  : 0xffc00000 - 0xfff00000   (3072 kB) 
 +[    0.000000]     vmalloc : 0x9f800000 - 0xff800000   (1536 MB) 
 +[    0.000000]     lowmem  : 0x80000000 - 0x9f000000   ( 496 MB) 
 +[    0.000000]     pkmap   : 0x7fe00000 - 0x80000000     2 MB) 
 +[    0.000000]     modules : 0x7f000000 - 0x7fe00000    14 MB) 
 +[    0.000000]       .text : 0x80008000 - 0x80a57450   (10558 kB) 
 +[    0.000000]       .init : 0x80b00000 - 0x80c00000   (1024 kB) 
 +[    0.000000]       .data : 0x80c00000 - 0x80c72fd8   ( 460 kB) 
 +[    0.000000]        .bss : 0x80c75000 - 0x80ce7098   ( 457 kB) 
 +[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 
 +[    0.000000] Preemptible hierarchical RCU implementation. 
 +[    0.000000] Build-time adjustment of leaf fanout to 32. 
 +[    0.000000] NR_IRQS:16 nr_irqs:16 16 
 +[    0.000000] Architected cp15 timer(s) running at 24.00MHz (virt). 
 +[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns 
 +[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns 
 +[    0.000016] Switching to timer-based delay loop, resolution 41ns 
 +[    0.000478] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) 
 +[    0.000490] pid_max: default: 32768 minimum: 301 
 +[    0.000581] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) 
 +[    0.000590] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) 
 +[    0.001113] Initializing cgroup subsys io 
 +[    0.001128] Initializing cgroup subsys memory 
 +[    0.001151] Initializing cgroup subsys devices 
 +[    0.001165] Initializing cgroup subsys freezer 
 +[    0.001175] Initializing cgroup subsys net_cls 
 +[    0.001185] Initializing cgroup subsys pids 
 +[    0.001207] CPU: Testing write buffer coherency: ok 
 +[    0.001590] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 
 +[    0.001640] Setting up static identity map for 0x41100000 - 0x41100058 
 +[    0.054106] MSM Memory Dump base table set up 
 +[    0.054131] MSM Memory Dump apps data table set up 
 +[    0.090233] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 
 +[    0.120219] CPU2: thread -1, cpu 2, socket 0, mpidr 80000002 
 +[    0.150254] CPU3: thread -1, cpu 3, socket 0, mpidr 80000003 
 +[    0.150308] Brought up 4 CPUs 
 +[    0.150327] SMP: Total of 4 processors activated (192.00 BogoMIPS). 
 +[    0.150333] CPU: All CPU(s) started in SVC mode. 
 +[    0.169938] VFP support v0.3: implementor 51 architecture 3 part 40 variant 3 rev 4 
 +[    0.170253] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns 
 +[    0.170277] futex hash table entries: 1024 (order: 4, 65536 bytes) 
 +[    0.170634] pinctrl core: initialized pinctrl subsystem 
 +[    0.171710] NET: Registered protocol family 16 
 +[    0.172813] DMA: preallocated 2048 KiB pool for atomic coherent allocations 
 +[    0.200085] cpuidle: using governor ladder 
 +[    0.230103] cpuidle: using governor menu 
 +[    0.230348] NET: Registered protocol family 42 
 +[    0.245869] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ! 
 +[    0.248889] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ! 
 +[    0.258587] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers. 
 +[    0.258596] hw-breakpoint: maximum watchpoint size is 8 bytes. 
 +[    0.260212] CPU: IPQ6018, SoC Version: 1.0 
 +[    0.260996] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 
 +[    0.262229] IPC logging disabled 
 +[    0.262235] IPC logging disabled 
 +[    0.262240] IPC logging disabled 
 +[    0.262245] IPC logging disabled 
 +[    0.262250] IPC logging disabled 
 +[    0.262459] sps:sps is ready. 
 +[    0.290950] socinfo_select_format: Unsupported format v0.13. Falling back to v0.12. 
 +[    0.290972] socinfo_print: v0.12, id=402, ver=1.0, raw_id=313, raw_ver=0, hw_plat=8, hw_plat_ver=196610 
 +[    0.290972]  accessory_chip=0, hw_plat_subtype=0, pmic_model=0, pmic_die_revision=0 foundry_id=2 serial_number=4268053074 num_pmics=0 chip_family=0x0 raw_device_family=0x2 raw_device_number=0x17 
 +[    0.291901] usbcore: registered new interface driver usbfs 
 +[    0.291963] usbcore: registered new interface driver hub 
 +[    0.292033] usbcore: registered new device driver usb 
 +[    0.292135] pps_core: LinuxPPS API ver. 1 registered 
 +[    0.292142] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> 
 +[    0.292168] PTP clock support registered 
 +[    0.294166] rpmsg_dev_probe: No pm domain 
 +[    0.295646] Bluetooth: Core ver 2.21 
 +[    0.295683] NET: Registered protocol family 31 
 +[    0.295690] Bluetooth: HCI device and connection manager initialized 
 +[    0.295702] Bluetooth: HCI socket layer initialized 
 +[    0.295712] Bluetooth: L2CAP socket layer initialized 
 +[    0.295736] Bluetooth: SCO socket layer initialized 
 +[    0.296008] clocksource: Switched to clocksource arch_sys_counter 
 +[    0.298840] NET: Registered protocol family 2 
 +[    0.299358] TCP established hash table entries: 4096 (order: 2, 16384 bytes) 
 +[    0.299407] TCP bind hash table entries: 4096 (order: 3, 32768 bytes) 
 +[    0.299482] TCP: Hash tables configured (established 4096 bind 4096) 
 +[    0.299519] UDP hash table entries: 256 (order: 1, 8192 bytes) 
 +[    0.299542] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) 
 +[    0.299693] NET: Registered protocol family 1 
 +[    0.300882] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 7 counters available 
 +[    0.309307] squashfs: version 4.0 (2009/01/31) Phillip Lougher 
 +[    0.309328] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. 
 +[    0.313236] Key type asymmetric registered 
 +[    0.313250] Asymmetric key parser 'x509' registered 
 +[    0.313285] io scheduler noop registered 
 +[    0.313298] io scheduler deadline registered (default) 
 +[    0.321374] NET: Registered protocol family 27 
 +[    0.321386] IPC_RTR: ipc_router_create_log_ctx: IPC Logging disabled 
 +[    0.321402] qmi_log_init: IPC Logging disabled 
 +[    0.321408] qmi_log_init: IPC Logging disabled 
 +[    0.321546] msm_rpm_log_probe: OK 
 +[    0.321872] msm-dcc b3000.dcc: DCC XPU is not specified 
 +[    0.322119] msm-dcc b3000.dcc: jiffies_64: 0xffff8aef, cntvct_64: 0x685d06c 
 +[    0.322132] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0x9fa2c004) 
 +[    0.322143] msm-dcc b3000.dcc: gcnt_lo: 0x0685d2d1(0x9fa2c000) 
 +[    0.322923] scm_call failed: func id 0x2000120 ret: -1 syscall returns: 0x0, 0x0, 0x0 
 +[    0.322931] TZ SMMU State: Can't detect SMMU State 
 +[    0.322983] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set 
 +[    0.323198] rpmsg_dev_probe: No pm domain 
 +[    0.324097] msm_serial 78b0000.serial: msm_serial: detected port #1 
 +[    0.324131] msm_serial 78b0000.serial: uartclk = 24000000 
 +[    0.324164] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 20, base_baud = 1500000) is a MSM 
 +[    0.324494] msm_serial 78b1000.serial: msm_serial: detected port #0 
 +[    0.324526] msm_serial 78b1000.serial: uartclk = 1843200 
 +[    0.324557] 78b1000.serial: ttyMSM0 at MMIO 0x78b1000 (irq = 21, base_baud = 115200) is a MSM 
 +[    0.324572] msm_serial: console setup on port #0 
 +[    1.102366] console [ttyMSM0] enabled 
 +[    1.107421] msm_serial: driver initialized 
 +[    1.110922] msm_serial_hsl_init: driver initialized 
 +[    1.124149] brd: module loaded 
 +[    1.129652] loop: module loaded 
 +[    1.130296] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 
 +[    1.133259] m25p80 spi32766.0: unrecognized JEDEC id bytes: 00,  0,  0 
 +[    1.139689] QPIC controller hw version Major:1, Minor:5 
 +[    1.145507] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa 
 +[    1.150405] nand: ONFI 10-Compliant Macronix MX30UF2G18AC 
 +[    1.156958] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 
 +[    1.162332] 20 ofpart partitions found on MTD device qcom_nand.0 
 +[    1.169718] Creating 20 MTD partitions on "qcom_nand.0": 
 +[    1.175870] 0x000000000000-0x000000180000 : "0:SBL1" 
 +[    1.183218] 0x000000180000-0x000000280000 : "0:MIBIB" 
 +[    1.187726] 0x000000280000-0x000000600000 : "0:QSEE" 
 +[    1.194476] 0x000000600000-0x000000680000 : "0:DEVCFG" 
 +[    1.197234] 0x000000680000-0x000000700000 : "0:RPM" 
 +[    1.202174] 0x000000700000-0x000000780000 : "0:CDT" 
 +[    1.206988] 0x000000780000-0x000000800000 : "0:APPSBLENV" 
 +[    1.211853] 0x000000800000-0x000000980000 : "0:APPSBL" 
 +[    1.218182] 0x000000980000-0x000000a00000 : "0:ART" 
 +[    1.222457] 0x000000a00000-0x000001300000 : "0:WIFIFW" 
 +[    1.233414] 0x000001300000-0x000001380000 : "0:ETHPHYFW" 
 +[    1.234625] 0x000001380000-0x000001400000 : "u_env" 
 +[    1.238917] 0x000001400000-0x000001440000 : "s_env" 
 +[    1.243322] 0x000001440000-0x000001480000 : "devinfo" 
 +[    1.248215] 0x000001480000-0x000006680000 : "kernel" 
 +[    1.314612] 0x000001c80000-0x000006680000 : "rootfs" 
 +[    1.370514] mtd: device 15 (rootfs) set to be root filesystem 
 +[    1.370772] mtdsplit: no squashfs found in "rootfs" 
 +[    1.375238] 0x000006680000-0x00000b880000 : "alt_kernel" 
 +[    1.441803] 0x000006e80000-0x00000b880000 : "alt_rootfs" 
 +[    1.497988] 0x00000b880000-0x00000ba80000 : "sysdiag" 
 +[    1.500291] 0x00000ba80000-0x00000fe80000 : "syscfg" 
 +[    1.554174] libphy: Fixed MDIO Bus: probed 
 +[    1.774941] qca-mdio 90000.mdio: Could not find phy-reset-gpio 
 +[    1.775082] libphy: qca_mdio: probed 
 +[    1.780916] qca-mdio 90000.mdio: qca-mdio driver was registered 
 +[    1.783522] PPP generic driver version 2.4.2 
 +[    1.789181] NET: Registered protocol family 24 
 +[    1.793547] PPTP driver version 0.8.5 
 +[    1.797992] Unable to create IPC log context! 
 +[    1.802083] cnss[2]: INFO: Platform driver probed successfully. plat 9dfe8010 tgt 0xfffd 
 +[    1.806519] dummy_hcd dummy_hcd.0: USB Host+Gadget Emulator, driver 02 May 2005 
 +[    1.814041] dummy_hcd dummy_hcd.0: Dummy host controller 
 +[    1.821103] dummy_hcd dummy_hcd.0: new USB bus registered, assigned bus number 1 
 +[    1.827262] hub 1-0:1.0: USB hub found 
 +[    1.834024] hub 1-0:1.0: 1 port detected 
 +[    1.838220] i2c /dev entries driver 
 +[    1.876520] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com 
 +[    1.876561] Bluetooth: HCI UART driver ver 2.3 
 +[    1.884015] Bluetooth: HCI UART protocol H4 registered 
 +[    1.888289] Bluetooth: HCI UART protocol BCSP registered 
 +[    1.893841] sdhci: Secure Digital Host Controller Interface driver 
 +[    1.898878] sdhci: Copyright(c) Pierre Ossman 
 +[    1.904854] sdhci-pltfm: SDHCI platform and OF driver helper 
 +[    1.910299] leds-pca963x 0-0062: PCA963X_HW_BLINK ON 
 +[    1.917387] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed 
 +[    1.920016] ICE IRQ = 32 
 +[    1.928636]  
 +[    1.928636] Version Rollback Feature Disabled 
 +[    1.931388] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x08b04000 
 +[    1.936572] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x08b04000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x08b04000 
 +[    1.952351] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x08b04000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x08b04000 
 +[    1.966845] sps:BAM 0x08b04000 is registered.[    1.975574] qcom-q6v5-wcss-pil cd00000.qcom_q6v5_wcss: ssr registeration success qcom_q6v5_wcss 
 +[    1.977629] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available 
 +[    1.986777] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000 
 +[    1.992883] coresight-csr 6001000.csr: CSR initialized 
 +[    2.000604] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000 
 +[    2.005578] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000 
 +[    2.013135] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000 
 +[    2.020502] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000 
 +[    2.027868] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000 
 +[    2.035227] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000 
 +[    2.042625] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000 
 +[    2.050087] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000 
 +[    2.057385] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000 
 +[    2.064746] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000 
 +[    2.072145] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000 
 +[    2.079518] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000 
 +[    2.086905] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000 
 +[    2.094259] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000 
 +[    2.101667] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000 
 +[    2.109036] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000 
 +[    2.116423] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000 
 +[    2.123921] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000 
 +[    2.131316] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000 
 +[    2.138727] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000 
 +[    2.146146] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000 
 +[    2.153458] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x06064000 
 +[    2.160516] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x06064000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x06064000 
 +[    2.176225] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x06064000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x06064000 
 +[    2.190717] sps:BAM 0x06064000 is registered.[    2.197741] coresight-tmc 6048000.tmc: TMC initialized 
 +[    2.201816] coresight-tmc 6047000.tmc: TMC initialized 
 +[    2.206969] coresight-funnel 6041000.funnel: FUNNEL initialized 
 +[    2.211967] coresight-funnel 6100000.funnel: FUNNEL initialized 
 +[    2.217796] coresight-funnel 6130000.funnel: FUNNEL initialized 
 +[    2.223679] coresight-funnel 6120000.funnel: FUNNEL initialized 
 +[    2.229614] coresight-funnel 61a1000.funnel: FUNNEL initialized 
 +[    2.236241] coresight-etm4x 619c000.etm: ETM 4.0 initialized 
 +[    2.241854] coresight-etm4x 619d000.etm: ETM 4.0 initialized 
 +[    2.247821] coresight-etm4x 619e000.etm: ETM 4.0 initialized 
 +[    2.253494] coresight-etm4x 619f000.etm: ETM 4.0 initialized 
 +[    2.258635] coresight-replicator-qcom 6046000.replicator: REPLICATOR 1.0 initialized 
 +[    2.264357] coresight-stm 6002000.stm: STM initialized 
 +[    2.273015] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000 
 +[    2.276786] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized 
 +[    2.284797] u32 classifier 
 +[    2.291924]     input device check on 
 +[    2.294428]     Actions configured 
 +[    2.298207] Netfilter messages via NETLINK v0.30. 
 +[    2.301484] nfnl_acct: registering with nfnetlink. 
 +[    2.306297] nf_conntrack version 0.5.0 (6678 buckets, 26712 max) 
 +[    2.311349] ctnetlink v0.93: registering with nfnetlink. 
 +[    2.317178] nf_conntrack_rtsp v0.7 loading 
 +[    2.322443] nf_tables: (c) 2007-2009 Patrick McHardy <kaber@trash.net> 
 +[    2.326330] nf_tables_compat: (c) 2012 Pablo Neira Ayuso <pablo@netfilter.org> 
 +[    2.333140] xt_time: kernel timezone is -0000 
 +[    2.340029] ip_set: protocol 6 
 +[    2.344623] gre: GRE over IPv4 demultiplexor driver 
 +[    2.347404] ip_gre: GRE over IPv4 tunneling driver 
 +[    2.353273] nf_nat_rtsp v0.7 loading 
 +[    2.357143] ip_tables: (C) 2000-2006 Netfilter Core Team 
 +[    2.360943] arp_tables: (C) 2002 David S. Miller 
 +[    2.366837] NET: Registered protocol family 10 
 +[    2.371657] ip6_tables: (C) 2000-2006 Netfilter Core Team 
 +[    2.375283] sit: IPv6 over IPv4 tunneling driver 
 +[    2.381610] ip6_gre: GRE over IPv6 tunneling driver 
 +[    2.385674] NET: Registered protocol family 17 
 +[    2.389717] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. 
 +[    2.394213] Bridge firewalling registered 
 +[    2.407151] Ebtables v2.0 registered 
 +[    2.411048] Bluetooth: RFCOMM TTY layer initialized 
 +[    2.414490] Bluetooth: RFCOMM socket layer initialized 
 +[    2.419133] Bluetooth: RFCOMM ver 1.11 
 +[    2.424303] Bluetooth: BNEP (Ethernet Emulation) ver 1.3 
 +[    2.428059] Bluetooth: BNEP filters: protocol multicast 
 +[    2.433501] Bluetooth: BNEP socket layer initialized 
 +[    2.438515] l2tp_core: L2TP core driver, V2.0 
 +[    2.443660] l2tp_netlink: L2TP netlink interface 
 +[    2.447965] 8021q: 802.1Q VLAN Support v1.8 
 +[    2.453426] Registering SWP/SWPB emulation handler 
 +[    2.458753] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 
 +[    2.462863] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 
 +[    2.468765] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0 
 +[    2.475862] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 2 
 +[    2.482479] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0 
 +[    2.490135] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable 
 +[    2.497649] cpr3_mem_acc_init: apc: not using memory accelerator regulator 
 +[    2.506780] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      SVS: open-loop= 675000 uV 
 +[    2.513715] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      NOM: open-loop= 787500 uV 
 +[    2.523713] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused    TURBO: open-loop= 850000 uV 
 +[    2.533518] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused   STURBO: open-loop= 900000 uV 
 +[    2.543368] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      SVS: quot[ 7]= 588, quot_offset[ 7]=   0 
 +[    2.553141] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      NOM: quot[ 7]= 784, quot_offset[ 7]= 195 
 +[    2.563991] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused    TURBO: quot[ 7]= 885, quot_offset[ 7]= 100 
 +[    2.574927] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused   STURBO: quot[ 7]= 958, quot_offset[ 7]=  70 
 +[    2.586130] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop 
 +[    2.598491] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 799999 KHz 
 +[    2.604223] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 864000 KHz 
 +[    2.612079] ubi0: attaching mtd17 
 +[    2.689814] random: nonblocking pool is initialized 
 +[    2.907448] ubi0: scanning is finished 
 +[    2.912439] ubi0 warning: print_rsvd_warning: cannot reserve enough PEBs for bad PEB handling, reserved 33, need 39 
 +[    2.912834] ubi0: attached mtd17 (name "alt_rootfs", size 74 MiB) 
 +[    2.921676] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes 
 +[    2.927926] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 
 +[    2.934688] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 
 +[    2.941553] ubi0: good PEBs: 591, bad PEBs: 1, corrupted PEBs: 0 
 +[    2.948322] ubi0: user volume: 1, internal volumes: 1, max. volumes count: 128 
 +[    2.954569] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1534575391 
 +[    2.961609] ubi0: available PEBs: 0, total reserved PEBs: 591, PEBs reserved for bad PEB handling: 33 
 +[    2.970905] ubi0: background thread "ubi_bgt0d" started, PID 134 
 +[    2.980868] input: soc:gpio_keys as /devices/platform/soc/soc:gpio_keys/input/input0 
 +[    2.986175] hctosys: unable to open rtc device (rtc0) 
 +[    3.002299] VFS: Mounted root (squashfs filesystem) readonly on device 31:20. 
 +[    3.003477] Freeing unused kernel memory: 1024K (80b00000 - 80c00000) 
 +********************************************************************************* 
 +              _        _  __    _    __ _____ __   __ _____ 
 +             | |      | ||  \  | |  / // ____]\ \ / // ____]TM 
 +             | |      | ||   \ | | / /| (___   \ V /| (____ 
 +             | |      | || |\ \| |\ \  \____ \  \ /  \____ \ 
 +             | |_____ | || | \   | \ \  ____) | | |   ____) | 
 +             |_______||_||_|  \__|  \_\[____ /  |_|  [_____/ 
 + 
 + (c) 2013 Belkin International, Inc. and/or its affiliates. All rights reserved. 
 + Booting elise (firmware version 1.1.7.209317)  
 +********************************************************************************* 
 +[utopia][init] System Initialization 
 +[utopia][init] Creating /proc 
 +[utopia][init] Creating /sys 
 +[utopia][init] Creating /dev 
 +[utopia][init] Creating /tmp 
 +[utopia][init] Allocating 60M for /tmp 
 +[utopia][init] Prepairing /dev/pts 
 +[utopia][init] Setting /tmp and /var permissions 
 +[utopia][init] Starting udev.. 
 +Attempting mount of ubifs syscfg partition 
 +UBI device number 1, total 544 LEBs (69074944 bytes, 65.9 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) 
 +[utopia][init] Using persistent syscfg data from /var/config/syscfg 
 +[utopia][init] Starting system logging 
 +[utopia][init] Starting sysevent subsystem 
 +[utopia][init] Starting blue ... 
 +[utopia][init] Checking HW version...XB 
 +[utopia][init] Enabling DesignWare USB3 DRD Core drivers 
 +[utopia][init] Loading QCA Ethernet, NSS and GMAC drivers 
 +net.netfilter.nf_conntrack_acct = 1 
 +[utopia][init] Late loading usb drivers 
 +modprobe: module nls_utf8 not found in modules.dep 
 +[utopia][init] Setting any unset system values to default 
 +[utopia][init] no persistence config file (/var/config/pstcfg) found 
 +setting up MAC addresses for all interface based on E8:9F:80:7B:B6:FB 
 +Updating NTP Servers if necessary 
 +[utopia][init] syscfg loaded removing tmp file 
 + SSDK Init OK! 
 +operation done. 
 + SSDK Init OK![Ethernet Type]:0x0 
 +operation done. 
 + SSDK Init OK! 
 +operation done. 
 + SSDK Init OK! 
 +operation done. 
 +checking for interactive script start up... 
 +no user scheduled tasks found... 
 +senq running  
 +/etc/init.d/service_senq.sh   Starting in mode 0 
 +1970-01-01 00:00:09: node-mode running  
 +Good block at 0x00000000 
 +Updating BootCount Page[21]:A800 ... Done 
 +[utopia][init] LAN Ports LED settings 
 +attempting to sync sysinfo.cgi auth credentials 
 +[utopia][init] Loading Buttons drivers 
 +[utopia][init] Setup link to WiFi firmware and board data (US) 
 +[utopia][init] Multi-region is not supported or not enabled 
 +[utopia][init] Cert region: US 
 +[utopia][init] No REGION definded, use FCC 
 +[utopia][init] Load WiFi cal data from MTD(mtd8) to FS. 
 +65536+0 records in 
 +65536+0 records out 
 +65536 bytes (64.0KB) copied, 0.236214 seconds, 270.9KB/s 
 +[utopia][init] Loading WLAN drivers 
 +/bin/sh: can't open '/etc/rc.common' 
 +[utopia][init] Loading QCA Enhanced Connection manager 
 +net.bridge.bridge-nf-call-ip6tables = 1 
 +net.bridge.bridge-nf-call-iptables = 1 
 +dev.nss.general.redirect = 1 
 +[utopia][init] Initializing BTLE interface 
 +[utopia][init] Bluetooth Mac Address: E8 9F 80 7B B6 FB 
 +[utopia][init] Cert Region: US 
 +[utopia][init] BT PSR: /etc/pb-234-csr8x11-rev2.psr 
 +Loading PSKEY_HCI_LMP_LOCAL_VERSION ... done 
 +Loading PSKEY_LMP_REMOTE_VERSION ... done 
 +Loading 0x212c ... done 
 +Loading 0x212d ... done 
 +Loading 0x212e ... done 
 +Loading 0x212f ... done 
 +Loading 0x2130 ... done 
 +Loading 0x2131 ... done 
 +Loading 0x2132 ... done 
 +Loading 0x2133 ... done 
 +Loading 0x2134 ... done 
 +Loading 0x2135 ... done 
 +Loading 0x2136 ... done 
 +Loading 0x2137 ... done 
 +Loading 0x220b ... done 
 +Loading 0x222b ... done 
 +Loading 0x222c ... done 
 +Loading 0x2139 ... done 
 +Loading 0x213a ... done 
 +Loading 0x213b ... done 
 +Loading PSKEY_LC_MAX_TX_POWER ... done 
 +Loading PSKEY_HOST_INTERFACE ... done 
 +Loading 0x01ea ... done 
 +Loading PSKEY_ANA_FREQ ... done 
 +Loading PSKEY_ANA_FTRIM ... done 
 +Loading 0x22c8 ... done 
 +Device setup complete 
 +[utopia][init] BTLE interface ready to use 
 +inserting fpbypass.ko for QCA 
 +attempting to sync sysinfo.cgi auth credentials 
 +adding group for lldpd user 
 +Thu Oct 11 06:00:00 UTC 2012 
 +Starting devicedb ...  
 +(none) login: wan, sysevent received: wan-start 
 +DeviceDB database version 3 
 +Options: 
 +    Daemonize       : yes 
 +    Server UDS Path   : /tmp/devicedb/server_link 
 +    Database File     : /tmp/devicedb/devicedb.db 
 +    DB Transient File : /tmp/devicedb/transient.db 
 +DeviceDB Daily Backup Cron job created 
 +No TopoDB persistence data to import 
 +TopoDB data not imported 
 +lldpd event lan_ipaddr 192.168.1.1 received.  
 +killall: lldpd: no process killed 
 +ping6: sendto: Network is unreachable 
 +lldpd event lldpd-start  received.  
 +lldpd configuration already running 
 +ARP agent not started: not in master mode. 
 +Starting ddd_ethernet_agent ...  
 +setting root_accessible to 0 by default 
 +mosquitto aborting: not Master 
 +lldp updating callback scripts 
 +service_guardian.sh is called with lan-status 
 +Entry tsmb lan-status, 1 
 +lldpd event lldp::root_accessible 0 received.  
 +nss_build_bypass is called with lan-started 
 +Lighttpd Model Base: MR73 
 +Generating Rainier lighttpd config 
 +Build temporary www configuration directory:  
 +TSLIIHauhEfGE 
 +ping6: sendto: Network is unreachable 
 +conntrack_parse running  
 +creating conntrack cron job 
 +ARP agent not started: not in master mode. 
 +Power cycle Ethernet ports. 
 +RTNETLINK answers: Device or resource busy 
 +lldpd event ETH::port_1_status down received.  
 +Registering Service myrouter._http._tcp.local port 80 
 +lldpd event ETH::port_2_status down received.  
 +wifi, sysevent received: lan-started (Wed Oct 10 23:00:08 PDT 2012) 
 +wifi, service_start() 
 +Got a reply for myrouter._http._tcp.local.: Name now registered and active 
 +[utopia][init] Loading GMAC and WLAN drivers 
 +[utopia][init] Creating wifi devices 
 + Multi-region is not supported or not enabled 
 +mosquitto aborting: not Master 
 +[utopia] Not setting ppp_clamp_mtu 
 +Entry tsmb lan-status, 1 
 +service_guardian.sh is called with lan-status 
 +lldpd event ETH::port_3_status down received.  
 +smart connect client, generating client device data 
 +lldpd event ETH::port_4_status down received.  
 +lldpd event ETH::port_5_status down received.  
 +backhaul_switching status event system_state-normal received 
 +ping6: sendto: Network is unreachable 
 +wifi, wifi_physical_start(ath0) 
 +backhaul_switching status event backhaul::media 0 received on backhaul_switching_mgr 
 +wifi, wl0_state=down, do not start physical ath0 
 +wifi, wifi_virtual_start(ath0) 
 +Backhaul media 0 received, but wifi status is not started. Will do backhaul check later 
 +wifi, wl0_state=down, do not start virtual ath0 
 +wifi, wifi_physical_start(ath1) 
 +wifi, wl1_state=down, do not start physical ath1 
 +wifi, wifi_virtual_start(ath1) 
 +wifi, wl1_state=down, do not start virtual ath1 
 +wifi, start_hostapd() 
 +BusyBox v1.19.4 (2021-12-03 16:56:05 PST) multi-call binary. 
 +Usage: grep [-HhnlLoqvsriwFE] [-m N] [-A/B/C N] PATTERN/-e PATTERN.../-f FILE [FILE]... 
 +Search for PATTERN in FILEs (or stdin) 
 + -H Add 'filename:' prefix 
 + -h Do not add 'filename:' prefix 
 + -n Add 'line_no:' prefix 
 + -l Show only names of files that match 
 + -L Show only names of files that don't match 
 + -c Show only count of matching lines 
 + -o Show only the matching part of line 
 + -q Quiet. Return 0 if PATTERN is found, 1 otherwise 
 + -v Select non-matching lines 
 + -s Suppress open and read errors 
 + -r Recurse 
 + -i Ignore case 
 + -w Match whole words only 
 + -F PATTERN is a literal (not regexp) 
 + -E PATTERN is an extended regexp 
 + -m N Match up to N times per file 
 + -A N Print N lines of trailing context 
 + -B N Print N lines of leading context 
 + -C N Same as '-A N -B N' 
 + -e PTRN Pattern to match 
 + -f FILE Read pattern from file 
 +start mcsd succeeded (Wed Oct 10 23:00:16 PDT 2012) 
 +23.00.16.434154 MCSD plugin   info : Initializing plugin manager 
 +ath0      no private ioctls. 
 +ath0      no transmit-power information. 
 +ath0      no transmit-power information. 
 +ath1      no transmit-power information. 
 +ath1      no transmit-power information. 
 +Not ready for JNAP. Sleeping for 15 seconds... 
 +configurator: got event(guardian-configured,
 +nss_build_bypass is called with guardian-configured 
 +killall: mdns_lookup: no process killed 
 +Entry tsmb tsmb-stop, 1 
 +LookUpMaster call OK. 
 +mDNS lookup is on going... 
 +smart_connect, sysevent received: wifi-status starting 
 +2012-10-11 06:00:26: Setting defaults 
 +[utopia] Not setting ppp_clamp_mtu on dslite protocol 
 +nss_build_bypass is called with ipv4_wan_ipaddr 
 +lldpd event ipv4_wan_ipaddr 0.0.0.0 received.  
 +fastpath, sysevent received: qos_enabled 
 +getting geoip information for 0.0.0.0 
 +  % Total    % Received % Xferd  Average Speed   Time    Time     Time  Current 
 +                                 Dload  Upload   Total   Spent    Left  Speed 
 + 
 +  0        0        0          0      0 --:--:-- --:--:-- --:--:--     0curl: (6) Could not resolve: freegeoip.net (Could not contact DNS servers) 
 +net.bridge.bridge-nf-call-ip6tables = 1 
 +net.bridge.bridge-nf-call-iptables = 1 
 +dev.nss.general.redirect = 1 
 +nss_build_bypass is called with build_bypass 
 +wan, sysevent received: phylink_wan_state 
 +Restarting nfqrecv service... 
 +btsetup service 
 +btsetup: smart_connect::setup_status 
 +state_machine entering READY 
 +configurator: got event(firewall-status, starting) 
 +btsetup: Unconfigured mode and Peripheral role 
 +pub_devinfo_status:  Error: could not determine HOST_ADDR 
 +bluetoothd.init: /var/run/dbus created 
 +bluetoothd.init: dbus-daemon started 
 +===> RESET ELISE usb power 
 +pub_wlan_status:  Error: could not determine HOST_ADDR 
 +smart_connect, sysevent received: wifi-status started 
 +configurator: got event(firewall-status, started) 
 +hcisetup: Enabled LE advertising 
 +btsetup[0] succeeded. 
 +configurator: got event(wan-status, starting) 
 +configurator: got event(firewall-status, starting) 
 +configurator: got event(firewall-status, started) 
 +Got a TERM signal, will terminate. 
 +Warning! nfqrecv encountered errors when doing recv(): Interrupted system call 
 +killall: nfqrecv: no process killed 
 +subscriber running  
 +/etc/init.d/service_subscriber.sh subscriber-stop NULL MODE: 0 
 +killall: omsgd: no process killed 
 +killall: configure_me_monitor.sh: no process killed 
 +rm: can't remove '/var/run/configure_me_monitor.sh.pid': No such file or directory 
 +configurator: got event(firewall-status, starting) 
 +configurator: got event(firewall-status, started) 
 +configurator: got event(firewall-status, starting) 
 +configurator: got event(nfqrecv-status, stopped) 
 +configurator: got event(firewall-status, started) 
 +configurator: got event(nfqrecv-status, started) 
 +configurator: got event(firewall-status, starting) 
 +configurator: got event(firewall-status, started) 
 +Entry tsmb tsmb-stop, 1 
 +Entry tsmb tsmb-start, 1 
 +[fw.sh] fwup_checked_after_boot:
 +[fwupd] status details:"ERROR: Connecting server" 
 +[fw.sh] fwup_forced_update:
 +</WRAP>\\ 
 + 
 +==== OEM bootlog v1.1.4 ====
 <WRAP bootlog>Format: Log Type - Time(microsec) - Message - Optional Info <WRAP bootlog>Format: Log Type - Time(microsec) - Message - Optional Info
 Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic
Line 943: Line 1659:
 Entry tsmb tsmb-start, 1</WRAP>\\ Entry tsmb tsmb-start, 1</WRAP>\\
  
-==== OpenWrt bootlog ====+==== U-Boot bootlog ====
 <WRAP bootlog> <WRAP bootlog>
-<nowiki>COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING</nowiki>+Format: Log Type - Time(microsec) - Message - Optional Info 
 +Log Type: B - Since Boot(Power On Reset),  D - Delta,  S - Statistic 
 +S - QC_IMAGE_VERSION_STRING=BOOT.XF.0.3-00077-IPQ60xxLZB-2 
 +S - IMAGE_VARIANT_STRING=IPQ6018LA 
 +S - OEM_IMAGE_VERSION_STRING=crm-ubuntu64 
 +S - Boot Interface: NAND 
 +S - Secure Boot: Off 
 +S - Boot Config @ 0x000a602c = 0x000002e5 
 +S - JTAG ID @ 0x000a607c = 0x001390e1 
 +S - OEM ID @ 0x000a6080 = 0x00000000 
 +S - Serial Number @ 0x000a4128 = 0xfe655252 
 +S - OEM Config Row 0 @ 0x000a4188 = 0x0000000000000000 
 +S - OEM Config Row 1 @ 0x000a4190 = 0x0000000000000000 
 +S - Feature Config Row 0 @ 0x000a4130 = 0x0000800018200021 
 +S - Feature Config Row 1 @ 0x000a4138 = 0x02c3e83783000009 
 +S - PBL Patch Ver: 1 
 +S - I-cache: On 
 +S - D-cache: On 
 +B -      3413 - PBL, Start 
 +B -       592 - bootable_media_detect_entry, Start 
 +B -      4339 - bootable_media_detect_success, Start 
 +B -      5147 - elf_loader_entry, Start 
 +B -      5319 - auth_hash_seg_entry, Start 
 +B -      7787 - auth_hash_seg_exit, Start 
 +B -      8280 - elf_segs_hash_verify_entry, Start 
 +B -    110428 - elf_segs_hash_verify_exit, Start 
 +B -    114852 - auth_xbl_sec_hash_seg_entry, Start 
 +B -    114995 - auth_xbl_sec_hash_seg_exit, Start 
 +B -    121548 - xbl_sec_segs_hash_verify_entry, Start 
 +B -    121549 - xbl_sec_segs_hash_verify_exit, Start 
 +B -    122478 - PBL, End 
 +B -    103242 - SBL1, Start 
 +B -    243329 - GCC [RstStat:0x0, RstDbg:0x600000] WDog Stat : 0x4 
 +B -    245769 - clock_init, Start 
 +D -      2836 - clock_init, Delta 
 +B -    254309 - boot_flash_init, Start 
 +D -     26169 - boot_flash_init, Delta 
 +B -    283680 - sbl1_ddr_set_default_params, Start 
 +D -       213 - sbl1_ddr_set_default_params, Delta 
 +B -    290299 - boot_config_data_table_init, Start 
 +D -      4727 - boot_config_data_table_init, Delta - (575 Bytes) 
 +B -    300120 - CDT Version:2,Platform ID:8,Major ID:3,Minor ID:2,Subtype:
 +B -    305000 - Image Load, Start 
 +D -      6619 - OEM_MISC Image Loaded, Delta - (0 Bytes) 
 +B -    314333 - Image Load, Start 
 +D -      5063 - PMIC Image Loaded, Delta - (0 Bytes) 
 +B -    322202 - sbl1_ddr_set_params, Start 
 +B -    327173 - CPR configuration: 0x366 
 +B -    330376 - Pre_DDR_clock_init, Start 
 +D -       183 - Pre_DDR_clock_init, Delta 
 +D -         0 - sbl1_ddr_set_params, Delta 
 +B -    367006 - Image Load, Start 
 +D -       458 - APDP Image Loaded, Delta - (0 Bytes) 
 +B -    380121 - Image Load, Start 
 +D -       427 - QTI_MISC Image Loaded, Delta - (0 Bytes) 
 +B -    382561 - Image Load, Start 
 +D -       945 - Auth Metadata 
 +D -       701 - Segments hash check 
 +D -     22326 - QSEE Dev Config Image Loaded, Delta - (36354 Bytes) 
 +B -    406839 - Image Load, Start 
 +D -      6527 - Auth Metadata 
 +D -     10645 - Segments hash check 
 +D -    329522 - QSEE Image Loaded, Delta - (1470632 Bytes) 
 +B -    736788 - Image Load, Start 
 +D -       702 - Auth Metadata 
 +D -       976 - Segments hash check 
 +D -     34526 - RPM Image Loaded, Delta - (102664 Bytes) 
 +B -    772992 - Image Load, Start 
 +D -       671 - Auth Metadata 
 +D -      3172 - Segments hash check 
 +D -    118828 - APPSBL Image Loaded, Delta - (561320 Bytes) 
 +B -    907436 - SBL1, End 
 +D -    804499 - SBL1, Delta 
 +S - Flash Throughput, 5000 KB/s  (2171545 Bytes,  422660 us) 
 +S - Core 0 Frequency, 800 MHz 
 +S - DDR Frequency, 466 MHz 
 +U-Boot 2016.01 (Mar 18 2020 - 13:15:21 +0800) 
 +CBT U-Boot ver: 2.3.01  ([IPQ6018].[SPF11.CSU1].[code version]) 
 +DRAM:  smem ram ptable found: ver: 2 len: 4 
 +512 MiB 
 +NAND:  ONFI device found 
 +ID = 1590aac2 
 +Vendor = c2 
 +Device = aa 
 +SF: Unsupported flash IDs: manuf 00, jedec 0000, ext_jedec 0000 
 +ipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0) 
 +256 MiB 
 +MMC:   sdhci: Node Not found, skipping initialization 
 +PCI0 is not defined in the device tree 
 +In:    serial@78B1000 
 +Out:   serial@78B1000 
 +Err:   serial@78B1000 
 +machid: 8030200 
 +eth0 MAC Address from ART is not valid 
 +eth1 MAC Address from ART is not valid 
 +eth2 MAC Address from ART is not valid 
 +eth3 MAC Address from ART is not valid 
 +eth4 MAC Address from ART is not valid 
 +eth5 MAC Address from ART is not valid 
 +Updating boot_count ... done 
 +Hit any key to stop autoboot:  1  0  
 +Net:   MAC0 addr:0:3:7f:ba:db:ad 
 +PHY ID1: 0x4d 
 +PHY ID2: 0xd0b1 
 +EDMA ver 1 hw init 
 +Num rings - TxDesc:1 (0-0) TxCmpl:1 (0-0) 
 +RxDesc:1 (15-15) RxFill:1 (7-7) 
 +ipq6018_edma_alloc_rings: successfull 
 +ipq6018_edma_setup_ring_resources: successfull 
 +ipq6018_edma_configure_rings: successfull 
 +ipq6018_edma_hw_init: successfull 
 +eth0 
 +IPQ6018# ? 
 +?       - alias for 'help' 
 +aq_load_fw- LOAD aq-fw-binary 
 +aq_phy_restart- Restart Aquantia phy 
 +base    - print or set address offset 
 +bdinfo  - print Board Info structure 
 +bootelf - Boot from an ELF image in memory 
 +bootipq - bootipq from flash device 
 +bootm   - boot application image from memory 
 +bootp   - boot image via network using BOOTP/TFTP protocol 
 +bootvx  - Boot vxWorks from an ELF image 
 +bootz   - boot Linux zImage image from memory 
 +canary  - test stack canary 
 +chpart  - change active partition 
 +cmp     - memory compare 
 +coninfo - print console devices and information 
 +cp      - memory copy 
 +crc32   - checksum calculation 
 +dcache  - enable or disable data cache 
 +devinfo - device info handling commands 
 +dhcp    - boot image via network using DHCP/TFTP protocol 
 +dm      - Driver model low level access 
 +echo    - echo args to console 
 +editenv - edit environment variable 
 +env     - environment handling commands 
 +erase   - erase FLASH memory 
 +exectzt - execute TZT 
 +exit    - exit script 
 +false   - do nothing, unsuccessfully 
 +fdt     - flattened device tree utility commands 
 +flash   - flash part_name  
 + flash part_name load_addr file_size  
 +flasherase- flerase part_name  
 +flinfo  - print FLASH memory information 
 +fuseipq - fuse QFPROM registers from memory 
 +go      - start application at address 'addr' 
 +help    - print command description/usage 
 +i2c     - I2C sub-system 
 +icache  - enable or disable instruction cache 
 +imxtract- extract a part of a multi-image 
 +ipq_mdio- IPQ mdio utility commands 
 +is_sec_boot_enabled- check secure boot fuse is enabled or not 
 +itest   - return true/false on integer compare 
 +loop    - infinite loop on address range 
 +md      - memory display 
 +mii     - MII utility commands 
 +mm      - memory modify (auto-incrementing address) 
 +mmc     - MMC sub system 
 +mmcinfo - display MMC info 
 +mtdparts- define flash/nand partitions 
 +mtest   - simple RAM read/write test 
 +mw      - memory write (fill) 
 +nand    - NAND sub-system 
 +nboot   - boot from NAND device 
 +nm      - memory modify (constant address) 
 +part    - disk partition related commands 
 +pci     - list and access PCI Configuration Space 
 +ping    - send ICMP ECHO_REQUEST to network host 
 +printenv- print environment variables 
 +protect - enable or disable FLASH write protection 
 +reset   - Perform RESET of the CPU 
 +run     - run commands in an environment variable 
 +runmulticore- Enable and schedule secondary cores 
 +saveenv - save environment variables to persistent storage 
 +secure_authenticate- authenticate the signed image 
 +setenv  - set environment variables 
 +setexpr - set environment variable as the result of eval expression 
 +sf      - SPI flash sub-system 
 +showvar - print local hushshell variables 
 +sleep   - delay execution for some time 
 +smeminfo- print SMEM FLASH information 
 +source  - run script from memory 
 +test    - minimal test like /bin/sh 
 +tftp    - boot image via network using TFTP protocol 
 +tftpput - TFTP put command, for uploading files to a server 
 +true    - do nothing, successfully 
 +uart    - UART sub-system 
 +ubi     - ubi commands 
 +usb     - USB sub-system 
 +usbboot - boot from USB device 
 +version - print monitor, compiler and linker version 
 +IPQ6018# version 
 +U-Boot 2016.01 (Mar 18 2020 - 13:15:21 +0800) 
 +arm-openwrt-linux-muslgnueabi-gcc (OpenWrt GCC 5.2.0 unknown) 5.2.0 
 +GNU ld (GNU Binutils) 2.24.0 
 +IPQ6018# printenv 
 +altkern=6680000 
 +auto_recovery=yes 
 +baudrate=115200 
 +boot_part=2 
 +boot_part_ready=3 
 +boot_ver=2.3.01 
 +bootargs=console=ttyMSM0,115200n8 
 +bootcmd=i2c dev 0 && i2c probe && i2c mw 0x62 0x00 0x00 1 && i2c mw 0x62 0x01 0x05 1 && i2c mw 0x62 0x08 0x00 1 && if test $auto_recovery = no; then bootipq; elif test $boot_part = 1; then run bootpart1; else run bootpart2; fi 
 +bootdelay=1 
 +bootpart1=setenv bootargs $partbootargs && nand read $loadaddr $prikern $kernsize && bootm $loadaddr 
 +bootpart2=setenv bootargs $partbootargs2 && nand read $loadaddr $altkern $kernsize && bootm $loadaddr 
 +ethact=eth0 
 +ethaddr=00:03:7f:ba:db:ad 
 +fdt_high=0x48500000 
 +fdtcontroladdr=4a477890 
 +flash_type=2 
 +flashimg=tftp $loadaddr $image && nand erase $prikern $imgsize && nand write $loadaddr $prikern $filesize 
 +flashimg2=tftp $loadaddr $image && nand erase $altkern $imgsize && nand write $loadaddr $altkern $filesize 
 +image=mr7350.img 
 +imgsize=5200000 
 +ipaddr=192.168.1.1 
 +kernsize=800000 
 +loadaddr=44000000 
 +machid=8030200 
 +mtddevname=fs 
 +mtddevnum=0 
 +mtdids=nand0=nand0 
 +mtdparts=mtdparts=nand0:0x4e00000@0x1880000(fs), 
 +netmask=255.255.255.0 
 +partbootargs=init=/sbin/init rootfstype=squashfs ubi.mtd=rootfs root=mtd:squashfs rootwait 
 +partbootargs2=init=/sbin/init rootfstype=squashfs ubi.mtd=alt_rootfs root=mtd:squashfs rootwait 
 +prikern=1480000 
 +serverip=192.168.1.254 
 +soc_version_major=1 
 +soc_version_minor=0 
 +stderr=serial@78B1000 
 +stdin=serial@78B1000 
 +stdout=serial@78B1000 
 +Environment size: 1505/262140 bytes 
 +</WRAP>\\ 
 + 
 +==== OpenWrt github.com/coolsnowwolf/openwrt-gl-ax1800 dmesg ==== 
 +<WRAP bootlog> 
 +<nowiki>$ ssh root@192.168.1.1 -o HostKeyAlgorithms=+ssh-rsa -o PubkeyAcceptedAlgorithms=+ssh-rsa 
 +root@192.168.1.1's password:  
 + 
 + 
 +BusyBox v1.30.1 () built-in shell (ash) 
 + 
 +  _______                     ________        __ 
 +       |.-----.-----.-----.|  |  |  |.----.|  |_ 
 +     ||  _  |  -__|     ||  |  |  ||   _||   _| 
 + |_______||   __|_____|__|__||________||__|  |____| 
 +          |__| W I R E L E S S   F R E E D O M 
 + ----------------------------------------------------- 
 + OpenWrt 19.07.9, r11405-2a3558b0de 
 + ----------------------------------------------------- 
 +root@OpenWrt:~# dmesg 
 +[    0.000000] Booting Linux on physical CPU 0x0 
 +[    0.000000] Initializing cgroup subsys cpuset 
 +[    0.000000] Initializing cgroup subsys cpu 
 +[    0.000000] Initializing cgroup subsys cpuacct 
 +[    0.000000] Linux version 4.4.60 (scott@desktop) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r11405-2a3558b0de) ) #0 SMP PREEMPT Wed Feb 16 20:47:59 2022 
 +[    0.000000] Boot CPU: AArch64 Processor [51af8014] 
 +[    0.000000] Ignoring memory range 0x40000000 - 0x41000000 
 +[    0.000000] Machine: Linksys MR7350 
 +[    0.000000] efi: Getting EFI parameters from FDT: 
 +[    0.000000] efi: UEFI not found. 
 +[    0.000000] cma: dma_contiguous_reserve(limit 60000000) 
 +[    0.000000] On node 0 totalpages: 111104 
 +[    0.000000]   DMA zone: 1736 pages used for memmap 
 +[    0.000000]   DMA zone: 0 pages reserved 
 +[    0.000000]   DMA zone: 111104 pages, LIFO batch:31 
 +[    0.000000] psci: probing for conduit method from DT. 
 +[    0.000000] psci: PSCIv1.0 detected in firmware. 
 +[    0.000000] psci: Using standard PSCI v0.2 function IDs 
 +[    0.000000] psci: MIGRATE_INFO_TYPE not supported. 
 +[    0.000000] PERCPU: Embedded 14 pages/cpu @ffffffc01ef61000 s19096 r8192 d30056 u57344 
 +[    0.000000] pcpu-alloc: s19096 r8192 d30056 u57344 alloc=14*4096 
 +[    0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3  
 +[    0.000000] Detected VIPT I-cache on CPU0 
 +[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 109368 
 +[    0.000000] Kernel command line: init=/sbin/init rootfstype=squashfs ubi.mtd=alt_rootfs root=mtd:squashfs rootwait root=/dev/ubiblock0_0 swiotlb=1 coherent_pool=2M 
 +[    0.000000] PID hash table entries: 2048 (order: 2, 16384 bytes) 
 +[    0.000000] Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) 
 +[    0.000000] Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) 
 +[    0.000000] software IO TLB [mem 0x5fe5c000-0x5fe9c000] (0MB) mapped at [ffffffc01ee5c000-ffffffc01ee9bfff] 
 +[    0.000000] Memory: 417408K/444416K available (5134K kernel code, 485K rwdata, 2488K rodata, 224K init, 405K bss, 27008K reserved, 0K cma-reserved) 
 +[    0.000000] Virtual kernel memory layout: 
 +[    0.000000]     vmalloc : 0xffffff8000000000 - 0xffffffbdbfff0000     246 GB) 
 +[    0.000000]     vmemmap : 0xffffffbdc0000000 - 0xffffffbfc0000000       8 GB maximum) 
 +[    0.000000]               0xffffffbdc0040000 - 0xffffffbdc0800000       7 MB actual) 
 +[    0.000000]     fixed   : 0xffffffbffa7fd000 - 0xffffffbffac00000    4108 KB) 
 +[    0.000000]     PCI I/O : 0xffffffbffae00000 - 0xffffffbffbe00000      16 MB) 
 +[    0.000000]     modules : 0xffffffbffc000000 - 0xffffffc000000000      64 MB) 
 +[    0.000000]     memory  : 0xffffffc000000000 - 0xffffffc01f000000     496 MB) 
 +[    0.000000]       .init : 0xffffffc0007f4000 - 0xffffffc00082c000     224 KB) 
 +[    0.000000]       .text : 0xffffffc000080000 - 0xffffffc0007f3034    7629 KB) 
 +[    0.000000]       .data : 0xffffffc00083a000 - 0xffffffc0008b3600     486 KB) 
 +[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 
 +[    0.000000] Preemptible hierarchical RCU implementation. 
 +[    0.000000] Build-time adjustment of leaf fanout to 64. 
 +[    0.000000] NR_IRQS:64 nr_irqs:64 0 
 +[    0.000000] Architected cp15 timer(s) running at 24.00MHz (virt). 
 +[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns 
 +[    0.000005] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns 
 +[    0.000418] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000) 
 +[    0.000429] pid_max: default: 32768 minimum: 301 
 +[    0.000508] Mount-cache hash table entries: 1024 (order: 1, 8192 bytes) 
 +[    0.000517] Mountpoint-cache hash table entries: 1024 (order: 1, 8192 bytes) 
 +[    0.001009] Initializing cgroup subsys io 
 +[    0.001027] Initializing cgroup subsys memory 
 +[    0.001055] Initializing cgroup subsys devices 
 +[    0.001069] Initializing cgroup subsys freezer 
 +[    0.001080] Initializing cgroup subsys net_cls 
 +[    0.001089] Initializing cgroup subsys pids 
 +[    0.001309] EFI services will not be available. 
 +[    0.001333] ASID allocator initialised with 65536 entries 
 +[    0.050529] MSM Memory Dump base table set up 
 +[    0.050550] MSM Memory Dump apps data table set up 
 +[    0.090111] Detected VIPT I-cache on CPU1 
 +[    0.090150] CPU1: Booted secondary processor [51af8014] 
 +[    0.120098] Detected VIPT I-cache on CPU2 
 +[    0.120124] CPU2: Booted secondary processor [51af8014] 
 +[    0.150125] Detected VIPT I-cache on CPU3 
 +[    0.150149] CPU3: Booted secondary processor [51af8014] 
 +[    0.150197] Brought up 4 CPUs 
 +[    0.150223] SMP: Total of 4 processors activated. 
 +[    0.150233] CPU: All CPU(s) started at EL1 
 +[    0.165694] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns 
 +[    0.165722] futex hash table entries: 1024 (order: 5, 131072 bytes) 
 +[    0.165945] pinctrl core: initialized pinctrl subsystem 
 +[    0.166826] NET: Registered protocol family 16 
 +[    0.190051] cpuidle: using governor ladder 
 +[    0.220068] cpuidle: using governor menu 
 +[    0.220252] NET: Registered protocol family 42 
 +[    0.220398] vdso: 2 pages (1 code @ ffffffc000841000, 1 data @ ffffffc000840000) 
 +[    0.221312] DMA: preallocated 2048 KiB pool for atomic allocations 
 +[    0.221402] Read of property:soc_version_minor from node failed 
 +[    0.221411] CPU: IPQ6018, SoC Version: 1.0 
 +[    0.221746] IPC logging disabled 
 +[    0.221752] IPC logging disabled 
 +[    0.221757] IPC logging disabled 
 +[    0.221762] IPC logging disabled 
 +[    0.221766] IPC logging disabled 
 +[    0.237357] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ! 
 +[    0.238123] sps:sps is ready. 
 +[    0.241012] irq: no irq domain found for /soc/smp2p-wcss/slave-kernel ! 
 +[    0.248372] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 
 +[    0.280862] socinfo_select_format: Unsupported format v0.13. Falling back to v0.12. 
 +[    0.280885] socinfo_print: v0.12, id=402, ver=1.0, raw_id=313, raw_ver=0, hw_plat=8, hw_plat_ver=196610 
 +[    0.280885]  accessory_chip=0, hw_plat_subtype=0, pmic_model=0, pmic_die_revision=0 foundry_id=2 serial_number=2327779025 num_pmics=0 chip_family=0x0 raw_device_family=0x2 raw_device_number=0x17 
 +[    0.281614] pps_core: LinuxPPS API ver. 1 registered 
 +[    0.281621] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it> 
 +[    0.281644] PTP clock support registered 
 +[    0.283258] rpmsg_dev_probe: No pm domain 
 +[    0.284652] clocksource: Switched to clocksource arch_sys_counter 
 +[    0.286860] NET: Registered protocol family 2 
 +[    0.287236] TCP established hash table entries: 4096 (order: 3, 32768 bytes) 
 +[    0.287285] TCP bind hash table entries: 4096 (order: 4, 65536 bytes) 
 +[    0.287361] TCP: Hash tables configured (established 4096 bind 4096) 
 +[    0.287407] UDP hash table entries: 256 (order: 1, 8192 bytes) 
 +[    0.287431] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) 
 +[    0.287576] NET: Registered protocol family 1 
 +[    0.287615] PCI: CLS 0 bytes, default 128 
 +[    0.293815] squashfs: version 4.0 (2009/01/31) Phillip Lougher 
 +[    0.293831] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. 
 +[    0.297250] Key type asymmetric registered 
 +[    0.297266] Asymmetric key parser 'x509' registered 
 +[    0.297296] io scheduler noop registered 
 +[    0.297309] io scheduler deadline registered (default) 
 +[    0.303326] msm_rpm_log_probe: OK 
 +[    0.303602] msm-dcc b3000.dcc: DCC XPU is not specified 
 +[    0.303845] msm-dcc b3000.dcc: jiffies_64: 0xffff8aed, cntvct_64: 0x61e7a73 
 +[    0.303856] msm-dcc b3000.dcc: gcnt_hi: 0x00000000(0xffffff800021e004) 
 +[    0.303867] msm-dcc b3000.dcc: gcnt_lo: 0x061e7c9b(0xffffff800021e000) 
 +[    0.304518] TZ SMMU State: Can't detect SMMU State 
 +[    0.304570] TZ Log : Will warn on Access Violation, as paniconaccessviolation is not set 
 +[    0.304793] rpmsg_dev_probe: No pm domain 
 +[    0.305198] msm_serial 78b0000.serial: msm_serial: detected port #1 
 +[    0.305233] msm_serial 78b0000.serial: uartclk = 24000000 
 +[    0.305265] 78b0000.serial: ttyMSM1 at MMIO 0x78b0000 (irq = 5, base_baud = 1500000) is a MSM 
 +[    0.305537] msm_serial 78b1000.serial: msm_serial: detected port #0 
 +[    0.305563] msm_serial 78b1000.serial: uartclk = 1843200 
 +[    0.305589] 78b1000.serial: ttyMSM0 at MMIO 0x78b1000 (irq = 6, base_baud = 115200) is a MSM 
 +[    0.305603] msm_serial: console setup on port #0 
 +[    1.012650] console [ttyMSM0] enabled 
 +[    1.017562] msm_serial: driver initialized 
 +[    1.021058] msm_serial_hsl_init: driver initialized 
 +[    1.033463] brd: module loaded 
 +[    1.037780] loop: module loaded 
 +[    1.038383] spi_qup 78b5000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 
 +[    1.041129] m25p80 spi32766.0: unrecognized JEDEC id bytes: 00,  0,  0 
 +[    1.047781] QPIC controller hw version Major:1, Minor:5 
 +[    1.053634] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xaa 
 +[    1.058527] nand: ONFI 10-Compliant Macronix MX30UF2G18AC 
 +[    1.065085] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 
 +[    1.070450] 20 ofpart partitions found on MTD device qcom_nand.0 
 +[    1.077843] Creating 20 MTD partitions on "qcom_nand.0": 
 +[    1.083997] 0x000000000000-0x000000180000 : "0:SBL1" 
 +[    1.091071] 0x000000180000-0x000000280000 : "0:MIBIB" 
 +[    1.095551] 0x000000280000-0x000000600000 : "0:QSEE" 
 +[    1.102261] 0x000000600000-0x000000680000 : "0:DEVCFG" 
 +[    1.105186] 0x000000680000-0x000000700000 : "0:RPM" 
 +[    1.110139] 0x000000700000-0x000000780000 : "0:CDT" 
 +[    1.114923] 0x000000780000-0x000000800000 : "0:APPSBLENV" 
 +[    1.119763] 0x000000800000-0x000000980000 : "0:APPSBL" 
 +[    1.126051] 0x000000980000-0x000000a00000 : "0:ART" 
 +[    1.130402] 0x000000a00000-0x000001300000 : "0:WIFIFW" 
 +[    1.140956] 0x000001300000-0x000001380000 : "0:ETHPHYFW" 
 +[    1.141927] 0x000001380000-0x000001400000 : "u_env" 
 +[    1.146306] 0x000001400000-0x000001440000 : "s_env" 
 +[    1.150704] 0x000001440000-0x000001480000 : "devinfo" 
 +[    1.155578] 0x000001480000-0x000006680000 : "kernel" 
 +[    1.218653] 0x000001c80000-0x000006680000 : "rootfs" 
 +[    1.271415] mtd: device 15 (rootfs) set to be root filesystem 
 +[    1.271669] mtdsplit: no squashfs found in "rootfs" 
 +[    1.276153] 0x000006680000-0x00000b880000 : "alt_kernel" 
 +[    1.339189] 0x000006e80000-0x00000b880000 : "alt_rootfs" 
 +[    1.392149] 0x00000b880000-0x00000ba80000 : "sysdiag" 
 +[    1.394186] 0x00000ba80000-0x00000fe80000 : "syscfg" 
 +[    1.445064] libphy: Fixed MDIO Bus: probed 
 +[    1.665764] qca-mdio 90000.mdio: Could not find phy-reset-gpio 
 +[    1.665878] libphy: qca_mdio: probed 
 +[    1.671610] qca-mdio 90000.mdio: qca-mdio driver was registered 
 +[    1.674336] i2c /dev entries driver 
 +[    1.715146] device-mapper: ioctl: 4.34.0-ioctl (2015-10-28) initialised: dm-devel@redhat.com 
 +[    1.715603] sdhci: Secure Digital Host Controller Interface driver 
 +[    1.722644] sdhci: Copyright(c) Pierre Ossman 
 +[    1.728656] sdhci-pltfm: SDHCI platform and OF driver helper 
 +[    1.733975] qcom_ice_get_device_tree_data: No vdd-hba-supply regulator, assuming not needed 
 +[    1.738865] ICE IRQ = 17 
 +[    1.748607]  
 +[    1.748607] Version Rollback Feature Disabled 
 +[    1.751756] remoteproc remoteproc0: cd00000.qcom_q6v5_wcss is available 
 +[    1.755794] of_graph_get_next_endpoint(): no port node found in /soc/csr@6001000 
 +[    1.761868] coresight-csr 6001000.csr: CSR initialized 
 +[    1.769608] of_graph_get_next_endpoint(): no port node found in /soc/cti@6010000 
 +[    1.774530] of_graph_get_next_endpoint(): no port node found in /soc/cti@6011000 
 +[    1.782105] of_graph_get_next_endpoint(): no port node found in /soc/cti@6012000 
 +[    1.789483] of_graph_get_next_endpoint(): no port node found in /soc/cti@6013000 
 +[    1.796858] of_graph_get_next_endpoint(): no port node found in /soc/cti@6014000 
 +[    1.804213] of_graph_get_next_endpoint(): no port node found in /soc/cti@6015000 
 +[    1.811611] of_graph_get_next_endpoint(): no port node found in /soc/cti@6016000 
 +[    1.818984] of_graph_get_next_endpoint(): no port node found in /soc/cti@6017000 
 +[    1.826361] of_graph_get_next_endpoint(): no port node found in /soc/cti@6018000 
 +[    1.833731] of_graph_get_next_endpoint(): no port node found in /soc/cti@6019000 
 +[    1.841121] of_graph_get_next_endpoint(): no port node found in /soc/cti@601a000 
 +[    1.848488] of_graph_get_next_endpoint(): no port node found in /soc/cti@601b000 
 +[    1.855875] of_graph_get_next_endpoint(): no port node found in /soc/cti@601c000 
 +[    1.863238] of_graph_get_next_endpoint(): no port node found in /soc/cti@601d000 
 +[    1.870634] of_graph_get_next_endpoint(): no port node found in /soc/cti@601e000 
 +[    1.878010] of_graph_get_next_endpoint(): no port node found in /soc/cti@601f000 
 +[    1.885384] of_graph_get_next_endpoint(): no port node found in /soc/cti@6198000 
 +[    1.892885] of_graph_get_next_endpoint(): no port node found in /soc/cti@6199000 
 +[    1.900256] of_graph_get_next_endpoint(): no port node found in /soc/cti@619a000 
 +[    1.907666] of_graph_get_next_endpoint(): no port node found in /soc/cti@619b000 
 +[    1.915075] of_graph_get_next_endpoint(): no port node found in /soc/cti@610c000 
 +[    1.922418] sps_register_bam_device : unable to create IPC Logging 0 for bam 0x0000000006064000 
 +[    1.929524] sps_register_bam_device : unable to create IPC Logging 1 for bam 0x0000000006064000sps_register_bam_device : unable to create IPC Logging 2 for bam 0x0000000006064000 
 +[    1.946617] sps_register_bam_device : unable to create IPC Logging 3 for bam 0x0000000006064000sps_register_bam_device : unable to create IPC Logging 4 for bam 0x0000000006064000 
 +[    1.962501] sps:BAM 0x0000000006064000 is registered.<6>   1.970178] coresight-tmc 6048000.tmc: TMC initialized 
 +[    1.974943] coresight-tmc 6047000.tmc: TMC initialized 
 +[    1.980068] coresight-funnel 6041000.funnel: FUNNEL initialized 
 +[    1.985110] coresight-funnel 6100000.funnel: FUNNEL initialized 
 +[    1.990914] coresight-funnel 6130000.funnel: FUNNEL initialized 
 +[    1.996829] coresight-funnel 6120000.funnel: FUNNEL initialized 
 +[    2.002732] coresight-funnel 61a1000.funnel: FUNNEL initialized 
 +[    2.009157] coresight-etm4x 619c000.etm: ETM 4.0 initialized 
 +[    2.014871] coresight-etm4x 619d000.etm: ETM 4.0 initialized 
 +[    2.020773] coresight-etm4x 619e000.etm: ETM 4.0 initialized 
 +[    2.026479] coresight-etm4x 619f000.etm: ETM 4.0 initialized 
 +[    2.031743] coresight-replicator-qcom 6046000.replicator: REPLICATOR 1.0 initialized 
 +[    2.037490] coresight-stm 6002000.stm: STM initialized 
 +[    2.046045] of_graph_get_next_endpoint(): no port node found in /soc/hwevent@6101000 
 +[    2.049916] coresight-hwevent 6101000.hwevent: Hardware Event driver initialized 
 +[    2.058494] NET: Registered protocol family 10 
 +[    2.065739] NET: Registered protocol family 17 
 +[    2.069379] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. 
 +[    2.073810] Bridge firewalling registered 
 +[    2.086555] 8021q: 802.1Q VLAN Support v1.8 
 +[    2.091711] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 
 +[    2.095697] qcom,cpr4-apss-regulator b018000.cpr4-ctrl: CPR valid fuse count: 4 
 +[    2.101860] cpr4_ipq807x_apss_read_fuse_data: apc_corner: speed bin = 0 
 +[    2.109057] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR fusing revision = 2 
 +[    2.115644] cpr4_ipq807x_apss_read_fuse_data: apc_corner: CPR misc fuse value = 0 
 +[    2.123278] cpr4_ipq807x_apss_read_fuse_data: apc_corner: Voltage boost fuse config = 0 boost = disable 
 +[    2.130805] cpr3_mem_acc_init: apc: not using memory accelerator regulator 
 +[    2.139934] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      SVS: open-loop= 675000 uV 
 +[    2.146883] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused      NOM: open-loop= 787500 uV 
 +[    2.156864] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused    TURBO: open-loop= 850000 uV 
 +[    2.166673] cpr4_ipq807x_apss_calculate_open_loop_voltages: apc_corner: fused   STURBO: open-loop= 925000 uV 
 +[    2.176515] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      SVS: quot[ 7]= 535, quot_offset[ 7]=   0 
 +[    2.186297] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused      NOM: quot[ 7]= 719, quot_offset[ 7]= 180 
 +[    2.197145] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused    TURBO: quot[ 7]= 814, quot_offset[ 7]=  95 
 +[    2.208084] cpr4_ipq807x_apss_calculate_target_quotients: apc_corner: fused   STURBO: quot[ 7]= 926, quot_offset[ 7]= 110 
 +[    2.219261] cpr3_regulator_init_ctrl: apc: Default CPR mode = closed-loop 
 +[    2.231504] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 799999 KHz 
 +[    2.237382] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 864000 KHz 
 +[    2.245308] ubi0: attaching mtd17 
 +[    2.321182] random: nonblocking pool is initialized 
 +[    2.541192] ubi0: scanning is finished 
 +[    2.546661] ubi0: attached mtd17 (name "alt_rootfs", size 74 MiB) 
 +[    2.546684] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes 
 +[    2.551724] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 
 +[    2.558508] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 
 +[    2.565360] ubi0: good PEBs: 592, bad PEBs: 0, corrupted PEBs: 0 
 +[    2.572122] ubi0: user volume: 2, internal volumes: 1, max. volumes count: 128 
 +[    2.578382] ubi0: max/mean erase counter: 2/0, WL threshold: 4096, image sequence number: 752153478 
 +[    2.585417] ubi0: available PEBs: 0, total reserved PEBs: 592, PEBs reserved for bad PEB handling: 40 
 +[    2.594361] ubi0: background thread "ubi_bgt0d" started, PID 135 
 +[    2.595196] block ubiblock0_0: created from ubi0:0(rootfs) 
 +[    2.611602] VFS: Mounted root (squashfs filesystem) readonly on device 252:0. 
 +[    2.615577] Freeing unused kernel memory: 224K (ffffffc0007f4000 - ffffffc00082c000) 
 +[    2.622492] Freeing alternatives memory: 40K (ffffffc00082c000 - ffffffc000836000) 
 +[    2.806673] init: Console is alive 
 +[    2.806773] init: - watchdog - 
 +[    3.244309] kmodloader: loading kernel modules from /etc/modules-boot.d/
 +[    3.255584] kmodloader: done loading kernel modules from /etc/modules-boot.d/
 +[    3.262433] init: - preinit - 
 +[    7.738827] UBIFS (ubi0:1): background thread "ubifs_bgt0_1" started, PID 230 
 +[    7.767631] UBIFS (ubi0:1): recovery needed 
 +[    7.851957] UBIFS (ubi0:1): recovery completed 
 +[    7.852042] UBIFS (ubi0:1): UBIFS: mounted UBI device 0, volume 1, name "rootfs_data" 
 +[    7.855407] UBIFS (ubi0:1): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes 
 +[    7.863259] UBIFS (ubi0:1): FS size: 61329408 bytes (58 MiB, 483 LEBs), journal size 3047424 bytes (2 MiB, 24 LEBs) 
 +[    7.873098] UBIFS (ubi0:1): reserved for root: 2896739 bytes (2828 KiB) 
 +[    7.883334] UBIFS (ubi0:1): media format: w4/r0 (latest is w4/r0), UUID 45DD6BFE-3A6C-4F31-8985-60D4B36FF509, small LPT model 
 +[    7.892718] mount_root: switching to ubifs overlay 
 +[    7.909792] urandom-seed: Seeding with /etc/urandom.seed 
 +[    7.938016] procd: - early - 
 +[    7.938064] procd: - watchdog - 
 +[    8.568473] procd: - watchdog - 
 +[    8.568613] procd: - ubus - 
 +[    8.622104] procd: - init - 
 +[    8.793199] kmodloader: loading kernel modules from /etc/modules.d/
 +[    8.827236] urngd: v1.0.2 started. 
 +[    8.850103] ssdk_switch_device_num_init[1159]:INFO:ess-switch dts node number: 1 
 +[    8.850176] ssdk_dt_get_switch_node[970]:INFO:ess-switch DT exist! 
 +[    8.856582] ssdk_dt_parse_access_mode[856]:INFO:switch_access_mode: local bus 
 +[    8.862550] ssdk_dt_parse_access_mode[869]:INFO:switchreg_base_addr: 0x3a000000 
 +[    8.869761] ssdk_dt_parse_access_mode[870]:INFO:switchreg_size: 0x1000000 
 +[    8.876889] ssdk_dt_parse_mac_mode[295]:INFO:mac mode = 0x0 
 +[    8.883813] ssdk_dt_parse_mac_mode[304]:INFO:mac mode1 = 0xff 
 +[    8.889202] ssdk_dt_parse_mac_mode[313]:INFO:mac mode2 = 0xff 
 +[    8.895149] ssdk_dt_parse_uniphy[332]:INFO:ess-uniphy DT exist! 
 +[    8.900939] ssdk_dt_parse_intf_mac[801]:INFO:dp1 MAC 00:03:7f:ba:db:ad 
 +[    8.906697] ssdk_plat_init start 
 +[    8.985733] ssdk_gcc_clock_init[1033]:INFO:SSDK gcc clock init successfully! 
 +[    8.986204] HPPE initializing... 
 +[    8.991990] malibu_phy_api_ops_init[2848]:INFO:qca probe malibu phy driver succeeded! 
 +[    8.998609] regi_init[3567]:INFO:Initializing HPPE!! 
 +[    9.214651] ssdk_ppe_reset_init[1265]:INFO:ppe reset successfully! 
 +[    9.217271] qca_hppe_tdm_hw_init[684]:INFO:tdm setup num=96 
 +[    9.219947] qca_hppe_portctrl_hw_init[107]:INFO:Cypress PPE port initializing 
 +[    9.335178] __adpt_hppe_uniphy_psgmii_mode_set[635]:INFO:uniphy 0 psgmii channel selection 
 +[    9.548872] ssdk_switch_register[1718]:INFO:Chip version 0x1501 
 +[    9.548907] qca_link_polling_select[1315]:INFO:link-polling-required node does not exist 
 +[    9.553591] ssdk_switch_register[1744]:INFO:polling is selected 
 +[    9.561933] regi_init[3571]:INFO:Initializing HPPE Done!! 
 +[    9.567621] regi_init[3631]:INFO:qca-ssdk module init succeeded! 
 +[    9.575004] EDMA ver 1 hw init 
 +[    9.579410] EDMA HW Reset completed succesfully 
 +[    9.582089] Num rings - TxDesc:1 (23-23) TxCmpl:1 (23-23) 
 +[    9.586518] RxDesc:1 (15-15) RxFill:1 (7-7) 
 +[    9.593716] GMAC2(ffffffc01b8fe880) Invalid MAC@ - using 3a:49:d8:a8:07:32 
 +[    9.597253] GMAC3(ffffffc01b8a2880) Invalid MAC@ - using 5a:f5:2d:11:6e:1a 
 +[    9.604059] GMAC4(ffffffc01b8a6880) Invalid MAC@ - using 1e:8d:5f:06:15:d7 
 +[    9.610940] GMAC5(ffffffc01c78a880) Invalid MAC@ - using 0e:65:ef:a3:ab:8c 
 +[    9.617835] ********************************************************** 
 +[    9.623554] * NSS Data Plane driver 
 +[    9.630115] ********************************************************** 
 +[    9.634899] l2tp_core: L2TP core driver, V2.0 
 +[    9.640455] l2tp_netlink: L2TP netlink interface 
 +[    9.763513] nss_driver - fw of size 860224  bytes copied to load addr: 40000000, nss_id : 0 
 +[    9.765440] Supported Frequencies -  
 +[    9.770935] 187.2 MHz 748.8 MHz  
 +[    9.776689] 1.4976 GHz <1>   9.777600]  
 +[    9.779986] ffffffbffc195e00: set sdma ffffffc01bb69100 
 +[    9.781533] node size 2 # items 4 
 +[    9.786407] memory: 40000000 536870912 (avl 439615488) items 4 active_cores 1 
 +[    9.789858] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000 
 +[    9.797000] ffffffbffc195e00: NSS core 0 DDR from 40000000 to 41000000 
 +[    9.803862] ffffffbffc195e00: meminfo init succeed 
 +[    9.826444] Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) 
 +[    9.829964] ip6_tables: (C) 2000-2006 Netfilter Core Team 
 +[    9.833516] Netfilter messages via NETLINK v0.30. 
 +[    9.838023] ip_set: protocol 6 
 +[    9.850765] PPP generic driver version 2.4.2 
 +[    9.851333] NET: Registered protocol family 24 
 +[    9.854140] node size 2 # items 4 
 +[    9.854146] memory: 40000000 536870912 (avl 439730176) items 4 active_cores 1 
 +[    9.854152] addr/size storage words 2 2 # words 4 in DTS, ddr size 1000000 
 +[    9.854156] ffffffbffc195e00: nss core 0 booted successfully 
 +[    9.878984] nss_wifi_meshmgr_init_module[1866]:Module Build Id: 04/23/23, 09:35:05 loaded 
 +[    9.883553] Loading modules backported from Linux version v3.18-503864-g787674a 
 +[    9.889999] Backport generated by backports.git v5.10-rc6-1-1-g79f0741 
 +[    9.898202] ip_tables: (C) 2000-2006 Netfilter Core Team 
 +[    9.905222] l2tp_ppp: PPPoL2TP kernel driver, V2.0 
 +[    9.911131] nf_conntrack version 0.5.0 (3263 buckets, 13052 max) 
 +[   10.056936] xt_FULLCONENAT: RFC3489 Full Cone NAT module 
 +[   10.056936] xt_FULLCONENAT: Copyright (C) 2018 Chion Tang <tech@chionlab.moe> 
 +[   10.072100] xt_time: kernel timezone is -0000 
 +[   10.132476] ath11k c000000.wifi: Not multipd architecture 
 +[   10.134993] ath11k c000000.wifi: ipq6018 hw1.0 
 +[   10.137235] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss 
 +[   10.141370] remoteproc remoteproc0: Booting fw image IPQ6018/q6_fw.mdt, size 7340 
 +[   11.034038] Subsystem error monitoring/handling services are up 
 +[   11.034329] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up 
 +[   11.034520] rpmsg_dev_probe: No pm domain 
 +[   11.034700] rpmsg_dev_probe: No pm domain 
 +[   11.045205] ------------[ cut here ]------------ 
 +[   11.045208] WARNING: at arch/arm64/mm/ioremap.c:58 
 +[   11.045279] Modules linked in: ath11k_ahb(+) ath11k_pci ath11k nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_quota xt_pkttype xt_physdev xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_addrtype xt_TCPMSS xt_REDIRECT xt_LOG xt_FULLCONENAT ppp_async nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack l2tp_ppp iptable_mangle iptable_filter ip_tables crc_ccitt compat qca_nss_wifi_meshmgr qca_nss_pppoe pppoe pppox ppp_generic slhc xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 bonding qca_nss_drv l2tp_netlink l2tp_core udp_tunnel ip6_udp_tunnel qca_nss_dp qca_ssdk leds_gpio gpio_button_hotplug 
 +[   11.045309]  
 +[   11.045314] CPU: 1 PID: 1011 Comm: kworker/u8:3 Not tainted 4.4.60 #0 
 +[   11.045315] Hardware name: Linksys MR7350 (DT) 
 +[   11.045327] Workqueue: qmi_msg_handler qmi_data_ready_work 
 +[   11.045329] task: ffffffc01bbcbf00 ti: ffffffc01bbcbf00 task.ti: ffffffc01bbcbf00 
 +[   11.045336] PC is at __ioremap_caller+0x70/0xe8 
 +[   11.045339] LR is at __ioremap_caller+0x6c/0xe8 
 +[   11.045341] pc : [<ffffffc000091690>] lr : [<ffffffc00009168c>] pstate: 80000145 
 +[   11.045342] sp : ffffffc01b457a80 
 +[   11.045346] x29: ffffffc01b457a80 x28: ffffffc019ee1a40  
 +[   11.045349] x27: ffffffc01b457b50 x26: ffffffc01db0f010  
 +[   11.045352] x25: ffffffc019ef2000 x24: ffffffc019ee0018  
 +[   11.045355] x23: 00e8000000000707 x22: ffffffbffc5365b4  
 +[   11.045358] x21: 0000000000000000 x20: 0000000050100000  
 +[   11.045361] x19: 0000000000100000 x18: 0000000002d9a328  
 +[   11.045364] x17: 0000000003da017d x16: 0000000092d322d9  
 +[   11.045367] x15: 000000004bf7025e x14: 0fffffffffffffff  
 +[   11.045370] x13: 0000000000000020 x12: 0101010101010101  
 +[   11.045372] x11: 0000000000000006 x10: 0101010101010101  
 +[   11.045376] x9 : ffffffffffffffff x8 : 7f7f7f7f7f7f7f7f  
 +[   11.045379] x7 : 0000000000000018 x6 : 0000000011c00000  
 +[   11.045382] x5 : ffffffc0008e0fc8 x4 : 0000000000000002  
 +[   11.045385] x3 : 0000000000000002 x2 : 0000000060000000  
 +[   11.045387] x1 : 0000000000000001 x0 : 0000000000000001  
 +[   11.045388]  
 +[   11.045390] ---[ end trace 51419203dbb5c34d ]--- 
 +[   11.045391] Call trace: 
 +[   11.045395] [<ffffffc000091690>] __ioremap_caller+0x70/0xe8 
 +[   11.045398] [<ffffffc000091718>] __ioremap+0x10/0x18 
 +[   11.045420] [<ffffffbffc5365b4>] ath11k_htc_init+0x202c/0x2378 [ath11k] 
 +[   11.045424] [<ffffffc0002f7f28>] qmi_invoke_handler+0x88/0xf0 
 +[   11.045427] [<ffffffc0002f81cc>] qmi_handle_message+0x23c/0x308 
 +[   11.045430] [<ffffffc0002f8b6c>] qmi_data_ready_work+0x3e4/0x408 
 +[   11.045436] [<ffffffc0000aa560>] process_one_work+0x1f8/0x330 
 +[   11.045439] [<ffffffc0000aa8f4>] worker_thread+0x25c/0x438 
 +[   11.045444] [<ffffffc0000b0230>] kthread+0xd0/0xe0 
 +[   11.045448] [<ffffffc000085540>] ret_from_fork+0x10/0x50 
 +[   11.045942] ath11k c000000.wifi: chip_id 0x0 chip_family 0x4 board_id 0xff soc_id 0xffffffff 
 +[   11.045946] ath11k c000000.wifi: fw_version 0x2506844c fw_build_timestamp 2021-07-13 11:09 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 
 +[   11.066512] ath11k c000000.wifi: qmi caldata downloaded: type: 2 
 +[   13.856279] remoteproc remoteproc0: stopped remote processor cd00000.qcom_q6v5_wcss 
 +[   13.856317] remoteproc remoteproc0: powering up cd00000.qcom_q6v5_wcss 
 +[   13.862873] remoteproc remoteproc0: Booting fw image IPQ6018/q6_fw.mdt, size 7340 
 +[   14.168138] Subsystem error monitoring/handling services are up 
 +[   14.168430] remoteproc remoteproc0: remote processor cd00000.qcom_q6v5_wcss is now up 
 +[   14.168617] rpmsg_dev_probe: No pm domain 
 +[   14.168861] rpmsg_dev_probe: No pm domain 
 +[   14.185342] ------------[ cut here ]------------ 
 +[   14.186308] kmodloader: done loading kernel modules from /etc/modules.d/
 +[   14.193522] WARNING: at arch/arm64/mm/ioremap.c:58 
 +[   14.200200] Modules linked in: iptable_nat nf_nat_ipv4 ath11k_ahb ath11k_pci ath11k nf_conntrack_ipv6 nf_conntrack_ipv4 mac80211 ipt_REJECT ipt_MASQUERADE cfg80211 xt_time xt_tcpudp xt_state xt_quota xt_pkttype xt_physdev xt_owner xt_nat xt_multiport xt_mark xt_mac xt_limit xt_id xt_conntrack xt_comment xt_addrtype xt_TCPMSS xt_REDIRECT xt_LOG xt_FULLCONENAT ppp_async nf_reject_ipv4 nf_nat_redirect nf_nat_masquerade_ipv4 nf_nat nf_log_ipv4 nf_defrag_ipv6 nf_defrag_ipv4 nf_conntrack_rtcache nf_conntrack l2tp_ppp iptable_mangle iptable_filter ip_tables crc_ccitt compat qca_nss_wifi_meshmgr qca_nss_pppoe pppoe pppox ppp_generic slhc xt_set ip_set_list_set ip_set_hash_netportnet ip_set_hash_netport ip_set_hash_netnet ip_set_hash_netiface ip_set_hash_net ip_set_hash_mac ip_set_hash_ipportnet ip_set_hash_ipportip ip_set_hash_ipport ip_set_hash_ipmark ip_set_hash_ip ip_set_bitmap_port ip_set_bitmap_ipmac ip_set_bitmap_ip ip_set nfnetlink nf_log_ipv6 nf_log_common ip6table_mangle ip6table_filter ip6_tables ip6t_REJECT x_tables nf_reject_ipv6 bonding qca_nss_drv l2tp_netlink l2tp_core udp_tunnel ip6_udp_tunnel qca_nss_dp qca_ssdk leds_gpio gpio_button_hotplug 
 +[   14.306441]  
 +[   14.306798] CPU: 2 PID: 1011 Comm: kworker/u8:3 Tainted: G        W       4.4.60 #0 
 +[   14.308366] Hardware name: Linksys MR7350 (DT) 
 +[   14.315749] Workqueue: qmi_msg_handler qmi_data_ready_work 
 +[   14.325715] task: ffffffc01bbcbf00 ti: ffffffc01bbcbf00 task.ti: ffffffc01bbcbf00 
 +[   14.325819] PC is at __ioremap_caller+0x70/0xe8 
 +[   14.333276] LR is at __ioremap_caller+0x6c/0xe8 
 +[   14.337614] pc : [<ffffffc000091690>] lr : [<ffffffc00009168c>] pstate: 80000145 
 +[   14.342133] sp : ffffffc01b457a80 
 +[   14.349763] x29: ffffffc01b457a80 x28: ffffffc019ee1a40  
 +[   14.358091] x27: ffffffc01b457b50 x26: ffffffc01db0f010  
 +[   14.363386] x25: ffffffc019ef2000 x24: ffffffc019ee0018  
 +[   14.368682] x23: 00e8000000000707 x22: ffffffbffc5365b4  
 +[   14.373977] x21: 0000000000000000 x20: 0000000050100000  
 +[   14.379272] x19: 0000000000100000 x18: 0000000000000000  
 +[   14.384568] x17: 0000000000001800 x16: 0000000000001400  
 +[   14.389862] x15: 000000000000000c x14: 011b010001180100  
 +[   14.395158] x13: 0117010001164b4e x12: 454c000415010001  
 +[   14.400453] x11: 0000000000000006 x10: 0101010101010101  
 +[   14.405749] x9 : ffffffffffffffff x8 : 7f7f7f7f7f7f7f7f  
 +[   14.411043] x7 : 0000000000000018 x6 : 0000000011c00000  
 +[   14.416337] x5 : ffffffc0008e0fc8 x4 : 0000000000000002  
 +[   14.421633] x3 : 0000000000000002 x2 : 0000000060000000  
 +[   14.426928] x1 : 0000000000000001 x0 : 0000000000000001  
 +[   14.432223]  
 +[   14.432399] ---[ end trace 51419203dbb5c34e ]--- 
 +[   14.433969] Call trace: 
 +[   14.438578] [<ffffffc000091690>] __ioremap_caller+0x70/0xe8 
 +[   14.440742] [<ffffffc000091718>] __ioremap+0x10/0x18 
 +[   14.446317] [<ffffffbffc5365b4>] ath11k_htc_init+0x202c/0x2378 [ath11k] 
 +[   14.451511] [<ffffffc0002f7f28>] qmi_invoke_handler+0x88/0xf0 
 +[   14.457857] [<ffffffc0002f81cc>] qmi_handle_message+0x23c/0x308 
 +[   14.463747] [<ffffffc0002f8b6c>] qmi_data_ready_work+0x3e4/0x408 
 +[   14.469479] [<ffffffc0000aa560>] process_one_work+0x1f8/0x330 
 +[   14.475727] [<ffffffc0000aa8f4>] worker_thread+0x25c/0x438 
 +[   14.481369] [<ffffffc0000b0230>] kthread+0xd0/0xe0 
 +[   14.486764] [<ffffffc000085540>] ret_from_fork+0x10/0x50 
 +[   14.493004] ath11k c000000.wifi: chip_id 0x0 chip_family 0x4 board_id 0xff soc_id 0xffffffff 
 +[   14.497035] ath11k c000000.wifi: fw_version 0x2506844c fw_build_timestamp 2021-07-13 11:09 fw_build_id QC_IMAGE_VERSION_STRING=WLAN.HK.2.5.0.1-01100-QCAHKSWPL_SILICONZ-1 
 +[   14.509773] ath11k c000000.wifi: qmi caldata downloaded: type: 2 
 +[   14.624633] applying ath11k-macs 
 +[   15.372665] ECM init 
 +[   15.372722] ECM database jhash random seed: 0x7152bdea 
 +[   15.375194] ECM init complete 
 +[   15.927246] configuring additional NSS pbufs 
 +[   15.937854] additional pbufs of size 3100672 got added to NSS 
 +[   16.182347] device eth0 entered promiscuous mode 
 +[   16.183172] br-lan: port 1(eth0) entered forwarding state 
 +[   16.186099] br-lan: port 1(eth0) entered forwarding state 
 +[   16.199021] device eth1 entered promiscuous mode 
 +[   16.199089] br-lan: port 2(eth1) entered forwarding state 
 +[   16.202743] br-lan: port 2(eth1) entered forwarding state 
 +[   16.210494] device eth2 entered promiscuous mode 
 +[   16.213478] br-lan: port 3(eth2) entered forwarding state 
 +[   16.218139] br-lan: port 3(eth2) entered forwarding state 
 +[   16.225818] device eth3 entered promiscuous mode 
 +[   16.228833] br-lan: port 4(eth3) entered forwarding state 
 +[   16.233475] br-lan: port 4(eth3) entered forwarding state 
 +[   16.242656] IPv6: ADDRCONF(NETDEV_UP): eth4: link is not ready 
 +[   16.594862] nss-dp 3a001200.dp2 eth1: PHY Link up speed: 1000 
 +[   16.614806] nss-dp 3a001800.dp5 eth4: PHY Link up speed: 1000 
 +[   16.614883] IPv6: ADDRCONF(NETDEV_CHANGE): eth4: link becomes ready 
 +[   16.701722] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready 
 +[   16.703788] device wlan0 entered promiscuous mode 
 +[   16.706832] br-lan: port 5(wlan0) entered forwarding state 
 +[   16.711376] br-lan: port 5(wlan0) entered forwarding state 
 +[   16.771613] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready 
 +[   16.773206] device wlan1 entered promiscuous mode 
 +[   16.776620] br-lan: port 6(wlan1) entered forwarding state 
 +[   16.781256] br-lan: port 6(wlan1) entered forwarding state 
 +[   16.889372] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready 
 +[   17.174698] br-lan: port 1(eth0) entered disabled state 
 +[   17.174934] br-lan: port 3(eth2) entered disabled state 
 +[   17.178830] br-lan: port 4(eth3) entered disabled state 
 +[   17.184019] br-lan: port 5(wlan0) entered disabled state 
 +[   17.200873] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready 
 +[   17.201001] br-lan: port 5(wlan0) entered forwarding state 
 +[   17.206333] br-lan: port 5(wlan0) entered forwarding state 
 +[   18.194660] br-lan: port 2(eth1) entered forwarding state 
 +[   18.774661] br-lan: port 6(wlan1) entered forwarding state 
 +[   19.204658] br-lan: port 5(wlan0) entered forwarding state 
 +[ 4250.565146] device wlan1 left promiscuous mode 
 +[ 4250.565213] br-lan: port 6(wlan1) entered disabled state 
 +[ 4251.679068] IPv6: ADDRCONF(NETDEV_UP): wlan1: link is not ready 
 +[ 4251.681014] device wlan1 entered promiscuous mode 
 +[ 4251.684173] br-lan: port 6(wlan1) entered forwarding state 
 +[ 4251.688715] br-lan: port 6(wlan1) entered forwarding state 
 +[ 4251.701557] br-lan: port 6(wlan1) entered disabled state 
 +[ 4251.719209] IPv6: ADDRCONF(NETDEV_CHANGE): wlan1: link becomes ready 
 +[ 4251.719372] br-lan: port 6(wlan1) entered forwarding state 
 +[ 4251.724739] br-lan: port 6(wlan1) entered forwarding state 
 +[ 4253.721421] br-lan: port 6(wlan1) entered forwarding state 
 +[ 4261.871810] device wlan0 left promiscuous mode 
 +[ 4261.871875] br-lan: port 5(wlan0) entered disabled state 
 +[ 4262.731480] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready 
 +[ 4262.733633] device wlan0 entered promiscuous mode 
 +[ 4262.736571] br-lan: port 5(wlan0) entered forwarding state 
 +[ 4262.741160] br-lan: port 5(wlan0) entered forwarding state 
 +[ 4262.911433] br-lan: port 5(wlan0) entered disabled state 
 +[ 4263.092660] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready 
 +[ 4263.092833] br-lan: port 5(wlan0) entered forwarding state 
 +[ 4263.098129] br-lan: port 5(wlan0) entered forwarding state 
 +[ 4265.091379] br-lan: port 5(wlan0) entered forwarding state 
 +[ 4354.850386] device wlan0 left promiscuous mode 
 +[ 4354.850461] br-lan: port 5(wlan0) entered disabled state 
 +[ 4355.656826] IPv6: ADDRCONF(NETDEV_UP): wlan0: link is not ready 
 +[ 4355.658912] device wlan0 entered promiscuous mode 
 +[ 4355.661791] br-lan: port 5(wlan0) entered forwarding state 
 +[ 4355.666464] br-lan: port 5(wlan0) entered forwarding state 
 +[ 4355.891080] br-lan: port 5(wlan0) entered disabled state 
 +[ 4356.013951] IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready 
 +[ 4356.014102] br-lan: port 5(wlan0) entered forwarding state 
 +[ 4356.019411] br-lan: port 5(wlan0) entered forwarding state 
 +[ 4358.011007] br-lan: port 5(wlan0) entered forwarding state</nowiki>
 </WRAP>\\ </WRAP>\\
  
  • Last modified: 2024/08/08 08:13
  • by hecatae