This is an old revision of the document!
Linksys E8350 V1
Write a short, relevant description of the device. Include a technical overview, but avoid marketing buzzwords/useless stuff. Two to four sentences is about right. A picture is good, too. Edit the page to see how to add pictures.
OpenWrt support
WiP. Developer discussion under: https://forum.openwrt.org/t/e8350-why-not-supported-by-openwrt/57640
Hardware highlights
| CPU | Ram | Flash | Network | WLAN | USB | Serial | JTag | eSata |
|---|---|---|---|---|---|---|---|---|
| Qualcomm dual-core IPQ8064 @ 1.4 GHz | 512 MiB | 4+128 MiB | 4x 10/100/100 | bgn + ac | 2x 3.0 | Yes | ? | Yes |
Debricking
Get the original firmware:
https://downloads.linksys.com/downloads/firmware/FW_E8350_1.0.03.003_20180929.bin
1. power off the device and disconnect the WAN port. (Only LAN port to be connected)
2. press & hold the “Reset” button
3. power on the deiece & wait for 10 seconds with pressed “Reset” button
- the Router will open Firmware Recovery “http” server on IP: 192.168.1.1
4. set IP on your PC from 192.168.1.0/24 network ( Router is on IP 192.168.1.1 )
5. open in browser URL:
http://192.168.1.1/index.shtml
Firmware Recovery -> File Name -> Recovery & Reboot
Hardware
Info
| Architecture | ARM (armv7l cortex-a15+neon vfpv4) |
|---|---|
| Vendor | Linksys |
| Bootloader | U-Boot |
| System-On-Chip | Qualcomm IPQ8064 @ 1.4 GHz |
| CPU/Speed | 2 x 1.4 GHz |
| Flash-Chips | SPI MX25U3235F + NAND MT29F1G08ABBDAH4 |
| Flash sizes | 4 MiB SPI + 128 MiB NAND |
| RAM | 512 MiB (491 MiB for the OS) |
| Wireless 1 | Qualcomm QCA9880 2.4GHz 802.11bgn |
| Wireless 2 | Quantenna QSR1000 5GHz 802.11ac |
| Ethernet | 4 x 10/100/1000 Mbit/s w/ vlan support |
| Switch | Qualcomm Atheros QCA8337 |
| USB | 2 x 3.0 |
| eSata | 1 (combo with one of the USB ports) |
| Serial | Yes|Not populated |
| JTAG | Not populated |
Photos
Opening the case
- Remove the rubber legs at the bottom side of the router.
- There are 4 screws which have to be removed.
- Use plastic card or similar tool and gently start opening it from the back side.
Serial
The serial port pins are unpopulated. You need to solder connecting cables or similar.
| Serial connection parameters for Linksys E8350 v1 | 115200, 8N1 |
|---|
USB to Serial TTL:
TX PCB board <> RX USB serial ttl dongle
RX PCB board <> TX USB serial ttl dongle
GND PCB board <> GND USB serial ttl dongle
JTAG
- JTAG is not tested. It looks like there are not populated JTAG pins on the PCB.
Bootlogs
OEM bootlog
U-Boot 2012.07-svn65 [local,local] (Sep 11 2015 - 09:46:52)
CyberTan U-Boot Version: v1.0
smem ram ptable found: ver: 0 len: 5 DRAM: 491 MiB NAND: SF: Detected MX25U3235F with page size 64 KiB, total 4 MiB ipq_spi: page_size: 0x100, sector_size: 0x10000, size: 0x400000 132 MiB In: serial Out: serial Err: serial cdp: get part failed for rootfs Net: MAC1 addr:0:3:7f:ba:db:1 athrs17_reg_init: complete athrs17_vlan_config ...done S17 inits done MAC2 addr:0:3:7f:ba:db:2 eth0 Warning: eth0 MAC addresses don't match: Address in SROM is 00:03:7f:ba:db:01 Address in environment is b4:75:0e:c0:03:6b , eth1 Warning: eth1 MAC addresses don't match: Address in SROM is 00:03:7f:ba:db:02 Address in environment is 00:06:3b:01:41:01
Hit any key to stop autoboot: 0 Device 1: nand1... is now current device Creating 1 MTD partitions on “nand0”: 0x000000000000-0x000004000000 : “mtd=0” UBI: attaching mtd2 to ubi0 UBI: physical eraseblock size: 131072 bytes (128 KiB) UBI: logical eraseblock size: 126976 bytes UBI: smallest flash I/O unit: 2048 UBI: VID header offset: 2048 (aligned 2048) UBI: data offset: 4096 UBI: attached mtd2 to ubi0 UBI: MTD device name: “mtd=0” UBI: MTD device size: 64 MiB UBI: number of good PEBs: 512 UBI: number of bad PEBs: 0 UBI: max. allowed volumes: 128 UBI: wear-leveling threshold: 4096 UBI: number of internal volumes: 1 UBI: number of user volumes: 3 UBI: available PEBs: 0 UBI: total number of reserved PEBs: 512 UBI: number of PEBs reserved for bad PEB handling: 5 UBI: max/mean erase counter: 2/0 Read 0 bytes from volume kernel to 44000000 No size specified → Using max size (1904640)
Image Name: Linux-3.4.0 Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1820472 Bytes = 1.7 MiB Load Address: 41508000 Entry Point: 41508000 Verifying Checksum ... OK Loading Kernel Image ... OK
OK Setting up atags for msm partition: rootfs
device nand0 <nand0>, # parts = 1 #: name size offset mask_flags 0: fs 0x04000000 0x00000000 0
active partition: nand0,0 - (fs) 0x04000000 @ 0x00000000
defaults: mtdids : none mtdparts: none Using machid 0x1260 from environment
Starting kernel ...
[ 0.000000] Booting Linux on physical CPU 0 [ 0.000000] Linux version 3.4.0 (zls@team2) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #14 SMP Fri Sep 28 15:57:55 EDT 2018 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5387d [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] Machine: Qualcomm Atheros AP148 reference board [ 0.000000] Partition (from atag) rootfs -- Offset:0 Size:200 [ 0.000000] memory pool 3 (start 5fc00000 size 400000) initialized [ 0.000000] Memory policy: ECC disabled, Data cache writealloc [ 0.000000] smem_find(137, 80): wrong size 72 [ 0.000000] socinfo_init: v6, id=202, ver=1.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536 [ 0.000000] accessory_chip=0 hw_plat_subtype=0 [ 0.000000] PERCPU: Embedded 8 pages/cpu @c0b39000 s10304 r8192 d14272 u32768 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 123690 [ 0.000000] Kernel command line: console=ttyHSL1,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes) [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Memory: 487MB = 487MB total [ 0.000000] Memory: 486700k/490796k available, 11988k reserved, 0K highmem [ 0.000000] Virtual kernel memory layout: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) [ 0.000000] vmalloc : 0xdf000000 - 0xff000000 ( 512 MB) [ 0.000000] lowmem : 0xc0000000 - 0xdeb00000 ( 491 MB) [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) [ 0.000000] .text : 0xc0008000 - 0xc04fc000 (5072 kB) [ 0.000000] .init : 0xc0500000 - 0xc0603840 (1039 kB) [ 0.000000] .data : 0xc0604000 - 0xc067eee0 ( 492 kB) [ 0.000000] .bss : 0xc067ef04 - 0xc07350ec ( 729 kB) [ 0.000000] SLUB: Genslabs=11, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] Hierarchical RCU implementation. [ 0.000000] NR_IRQS:1689 [ 0.000000] sched_clock: 32 bits at 32kHz, resolution 31240ns, wraps every 134175798ms [ 0.000000] Console: colour dummy device 80×30 [ 0.150421] Calibrating delay using timer specific routine.. 12.55 BogoMIPS (lpj=62782) [ 0.150452] pid_max: default: 32768 minimum: 301 [ 0.150921] Mount-cache hash table entries: 512 [ 0.152452] CPU: Testing write buffer coherency: ok [ 0.152671] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000 [ 0.152702] Setting up static identity map for 0x41897b70 - 0x41897bf8 [ 0.154826] CPU1: Booted secondary processor [ 0.154920] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001 [ 0.154982] Brought up 2 CPUs [ 0.155014] SMP: Total of 2 processors activated (25.11 BogoMIPS). [ 0.170665] dummy: [ 0.171321] NET: Registered protocol family 16 [ 0.172071] AXI: msm_bus_fabric_init_driver(): msm_bus_fabric_init_driver [ 0.174476] meminfo_init: smem ram ptable found: ver: 0 len: 5 [ 0.174507] Found 1 memory banks grouped into 8 memory regions [ 0.175070] gpiochip_add: registered GPIOs 0 to 151 on device: msmgpio [ 0.175570] QFPROM TSENS calibration data not present [ 0.175601] smem_find(137, 80): wrong size 72 [ 0.175632] socinfo_init: v6, id=202, ver=1.0, raw_id=2064, raw_ver=2064, hw_plat=0, hw_plat_ver=65536 [ 0.175632] accessory_chip=0 hw_plat_subtype=0 [ 0.175663] msm_rpm_init: RPM firmware 3.0.16777338 [ 0.183255] clk_tbl_nss - loaded [ 0.185567] msm_rpm_get_status(): Status id 393 not defined for target [ 0.185567] msm_rpm_get_status(): Status id 393 not defined for target [ 0.185598] msm_rpm_get_status(): Status id 393 not defined for target [ 0.185598] msm_rpm_get_status(): Status id 393 not defined for target [ 0.185629] msm_rpm_get_status(): Status id 393 not defined for target [ 0.185629] msm_rpm_get_status(): Status id 393 not defined for target [ 0.194782] Register DIAG LED in /proc/sys/diag_blink. [ 0.209903] msm_dmov_memcpy_init: Success [ 0.216369] sps:BAM 0x12244000 enabled: ver:0x5, number of pipes:20 [ 0.216401] sps:BAM 0x12244000 is registered. [ 0.216651] sps:sps is ready. [ 0.310934] msm_pcie_setup: link initialized [ 0.311277] PCI host bridge to bus 0000:00 [ 0.311308] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fefffff] [ 0.311808] PCI: bus0: Fast back to back transfers disabled [ 0.312683] PCI: bus1: Fast back to back transfers disabled [ 0.330990] msm_pcie_setup: link initialized [ 0.331333] PCI host bridge to bus 0000:02 [ 0.331333] pci_bus 0000:02: root bus resource [mem 0x2e000000-0x31efffff] [ 0.331802] PCI: bus2: Fast back to back transfers disabled [ 0.332646] PCI: bus3: Fast back to back transfers disabled [ 1.353858] msm_pcie_setup: link initialization failed [ 1.354108] pci 0000:02:00.0: BAR 8: assigned [mem 0x2e000000-0x2e1fffff] [ 1.354108] pci 0000:02:00.0: BAR 9: assigned [mem 0x2e200000-0x2e2fffff pref] [ 1.354139] pci 0000:03:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 1.354170] pci 0000:03:00.0: BAR 6: assigned [mem 0x2e200000-0x2e20ffff pref] [ 1.354201] pci 0000:02:00.0: PCI bridge to [bus 03-03] [ 1.354201] pci 0000:02:00.0: bridge window [mem 0x2e000000-0x2e1fffff] [ 1.354233] pci 0000:02:00.0: bridge window [mem 0x2e200000-0x2e2fffff pref] [ 1.354264] PCI: enabling device 0000:02:00.0 (0140 → 0143) [ 1.354358] pci 0000:00:00.0: BAR 9: assigned [mem 0x08000000-0x080fffff pref] [ 1.354358] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x0800ffff pref] [ 1.354389] pci 0000:01:00.0: BAR 2: assigned [mem 0x08010000-0x0801ffff pref] [ 1.354420] pci 0000:01:00.0: BAR 3: assigned [mem 0x08020000-0x0802ffff pref] [ 1.354451] pci 0000:00:00.0: PCI bridge to [bus 01-01] [ 1.354482] pci 0000:00:00.0: bridge window [mem 0x08000000-0x080fffff pref] [ 1.354514] PCI: enabling device 0000:00:00.0 (0140 → 0143) [ 1.375101] bio: create slab <bio-0> at 0 [ 1.376538] SCSI subsystem initialized [ 1.378350] spi_qsd spi_qsd.5: master is unqueued, this is deprecated [ 1.380693] spi_qsd spi_qsd.6: master is unqueued, this is deprecated [ 1.383036] spi_qsd spi_qsd.2: master is unqueued, this is deprecated [ 1.388034] Switching to clocksource gp_timer [ 1.407341] NET: Registered protocol family 2 [ 1.407685] IP route cache hash table entries: 4096 (order: 2, 16384 bytes) [ 1.408216] TCP established hash table entries: 16384 (order: 5, 131072 bytes) [ 1.408403] TCP bind hash table entries: 16384 (order: 5, 131072 bytes) [ 1.408622] TCP: Hash tables configured (established 16384 bind 16384) [ 1.408622] TCP: reno registered [ 1.408653] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 1.408653] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 1.409122] NET: Registered protocol family 1 [ 1.411090] smd: register irq failed on wcnss_a11 [ 1.411121] smd: deregistering IRQs [ 1.411184] SMD: smd_core_platform_init() failed [ 1.412027] Partition(from smem) sbl1 -- Offset:0 Size:10000 [ 1.412027] Partition(from smem) mibib -- Offset:10000 Size:20000 [ 1.412058] Partition(from smem) sbl2 -- Offset:30000 Size:20000 [ 1.412089] Partition(from smem) sbl3 -- Offset:50000 Size:30000 [ 1.412089] Partition(from smem) ddrconfig -- Offset:80000 Size:10000 [ 1.412121] Partition(from smem) ssd -- Offset:90000 Size:10000 [ 1.412152] Partition(from smem) tz -- Offset:a0000 Size:30000 [ 1.412183] Partition(from smem) rpm -- Offset:d0000 Size:20000 [ 1.412183] Partition(from smem) oldappsbl -- Offset:f0000 Size:40000 [ 1.412214] Partition(from smem) APPSBLENV -- Offset:130000 Size:40000 [ 1.412214] Partition(from smem) ART -- Offset:170000 Size:20000 [ 1.412246] Partition(from smem) uboot -- Offset:190000 Size:50000 [ 1.412277] Partition(from smem) oldnss1 -- Offset:1e0000 Size:20000 [ 1.412308] Partition(from smem) nvram -- Offset:200000 Size:20000 [ 1.412308] Partition(from smem) oldkernel -- Offset:220000 Size:1e0000 [ 1.427460] acpuclk-ipq806x acpuclk-ipq806x: SPEED BIN: 0 [ 1.427460] acpuclk-ipq806x acpuclk-ipq806x: ACPU PVS: 2 [ 1.435238] acpuclk-ipq806x acpuclk-ipq806x: CPU0: 6 frequencies supported [ 1.435270] acpuclk-ipq806x acpuclk-ipq806x: CPU1: 6 frequencies supported [ 1.436863] msm_rpm_log_probe: OK [ 1.457388] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.457419] jffs2: version 2.2. (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) �© 2001-2006 Red Hat, Inc. [ 1.459325] msgmni has been set to 950 [ 1.461105] io scheduler noop registered [ 1.461137] io scheduler deadline registered (default) [ 1.461824] HDLC line discipline maxframe=4096 [ 1.461824] N_HDLC line discipline registered. [ 1.462855] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.465167] msm_serial_hs module loaded [ 1.465417] msm_serial_hsl: detected port #1 [ 1.465635] msm_serial_hsl.1: ttyHSL1 at MMIO 0x16340000 (irq = 184) is a MSM [ 1.466104] msm_serial_hsl: console setup on port #1 [ 2.296813] console [ttyHSL1] enabled [ 2.300093] msm_serial_hsl: driver initialized [ 2.309809] ahci ahci.0: forcing PORTS_IMPL to 0x1 [ 2.313620] ahci ahci.0: AHCI 0001.0300 32 slots 1 ports 6 Gbps 0x1 impl platform mode [ 2.321774] ahci ahci.0: flags: ncq sntf pm led clo only pmp pio slum part ccc apst [ 2.330521] scsi0 : ahci_platform [ 2.333520] ata1: SATA max UDMA/133 mmio [mem 0x29000000-0x2900017f] port 0x100 irq 241 [ 2.343111] msm_nand_probe: phys addr 0x1ac00000 [ 2.346797] msm_nand_probe: dmac 0x3 [ 2.350421] msm_nand_probe: allocated dma buffer at ffdfc000, dma_addr 5ec26000 [ 2.359075] status: 20 [ 2.360418] nandid: 1580a12c maker 2c device a1 [ 2.364948] ONFI probe : Found an ONFI compliant device MT29F1G08ABBDAH4 , [ 2.372196] Found a supported NAND device [ 2.376038] NAND Controller ID : 0x4030 [ 2.379912] NAND Device ID : 0x1580a12c [ 2.383755] Buswidth : 8 Bits [ 2.386722] Density : 128 MByte [ 2.389971] Pagesize : 2048 Bytes [ 2.393220] Erasesize: 131072 Bytes [ 2.396688] Oobsize : 64 Bytes [ 2.399843] CFG0 Init : 0xa8d408c0 [ 2.403311] CFG1 Init : 0x0004745c [ 2.406779] ECCBUFCFG : 0x00000203 [ 2.410996] Creating 1 MTD partitions on “msm_nand”: [ 2.415213] 0x000000000000-0x000004000000 : “rootfs” [ 2.567728] mtd: partition “rootfs” set to be root filesystem [ 2.573320] split_squashfs: no squashfs found in “msm_nand” [ 2.578569] m25p80 spi5.0: found mx25u3235f, expected s25fl512s [ 2.583911] m25p80 spi5.0: mx25u3235f (4096 Kbytes) [ 2.589409] Creating 15 MTD partitions on “m25p80”: [ 2.593626] 0x000000000000-0x000000010000 : “sbl1” [ 2.600843] 0x000000010000-0x000000030000 : “mibib” [ 2.606997] 0x000000030000-0x000000050000 : “sbl2” [ 2.613214] 0x000000050000-0x000000080000 : “sbl3” [ 2.619431] 0x000000080000-0x000000090000 : “ddrconfig” [ 2.625929] 0x000000090000-0x0000000a0000 : “ssd” [ 2.631896] 0x0000000a0000-0x0000000d0000 : “tz” [ 2.637425] 0x0000000d0000-0x0000000f0000 : “rpm” [ 2.643142] 0x0000000f0000-0x000000130000 : “oldappsbl” [ 2.649015] 0x000000130000-0x000000170000 : “APPSBLENV” [ 2.654607] 0x000000170000-0x000000190000 : “ART” [ 2.659731] 0x000000190000-0x0000001e0000 : “uboot” [ 2.664979] 0x0000001e0000-0x000000200000 : “oldnss1” [ 2.670509] 0x000000200000-0x000000220000 : “nvram” [ 2.675820] 0x000000220000-0x000000400000 : “oldkernel” [ 2.682193] UBI: attaching mtd0 to ubi0 [ 2.685004] UBI: physical eraseblock size: 131072 bytes (128 KiB) [ 2.691283] UBI: logical eraseblock size: 126976 bytes [ 2.696626] UBI: smallest flash I/O unit: 2048 [ 2.698094] ata1: SATA link down (SStatus 0 SControl 300) [ 2.706747] UBI: VID header offset: 2048 (aligned 2048) [ 2.712714] UBI: data offset: 4096 [ 3.708372] UBI: max. sequence number: 11 [ 3.735363] UBI: attached mtd0 to ubi0 [ 3.738144] UBI: MTD device name: “rootfs” [ 3.743142] UBI: MTD device size: 64 MiB [ 3.748016] UBI: number of good PEBs: 512 [ 3.752608] UBI: number of bad PEBs: 0 [ 3.757013] UBI: number of corrupted PEBs: 0 [ 3.761480] UBI: max. allowed volumes: 128 [ 3.766041] UBI: wear-leveling threshold: 4096 [ 3.770759] UBI: number of internal volumes: 1 [ 3.775164] UBI: number of user volumes: 3 [ 3.779631] UBI: available PEBs: 0 [ 3.784004] UBI: total number of reserved PEBs: 512 [ 3.788909] UBI: number of PEBs reserved for bad PEB handling: 5 [ 3.794876] UBI: max/mean erase counter: 2/0 [ 3.799156] UBI: image sequence number: 966812879 [ 3.803936] UBI: background thread “ubi_bgt0d” started, PID 626 [ 3.809965] UBI error: ubi_init: cannot attach mtd0 [ 3.835988] _nvram_read: read len=0xff00, magic=48534c46 [ 3.875132] GPIO Bitbanged MDIO: probed [ 3.880162] PPP generic driver version 2.4.2 [ 3.883973] NET: Registered protocol family 24 [ 3.888034] tsens_tm_probe : TSENS early init not done. [ 3.893064] tsens8960-tm: probe of tsens8960-tm failed with error -14 [ 3.901280] cpuidle: using governor ladder [ 3.904342] cpuidle: using governor menu [ 3.909809] TCP: cubic registered [ 3.913714] NET: Registered protocol family 10 [ 3.918931] IPv6 over IPv4 tunneling driver [ 3.925335] NET: Registered protocol family 17 [ 3.929272] Bridge firewalling registered [ 3.932739] 8021q: 802.1Q VLAN Support v1.8 [ 3.937019] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 3.944673] Registering SWP/SWPB emulation handler [ 3.949453] clock_late_init: Removing enables held for handed-off clocks [ 3.964042] ipq_nss_get_mac_addr: MAC[0]: ff:ff:ff:ff:ff:ff [ 3.968759] ipq_nss_get_mac_addr: MAC[1]: ff:ff:ff:ff:ff:ff [ 3.974258] ipq_nss_get_mac_addr: MAC[2]: ff:ff:ff:ff:ff:ff [ 3.979818] ipq_nss_get_mac_addr: MAC[3]: ff:ff:ff:ff:ff:ff [ 3.985442] no pmic restart interrupt specified [ 3.991471] msm_cache_dump_probe: could not register L2 buffer ret = -22. [ 4.007341] VFS: Mounted root (squashfs filesystem) readonly on device 31:17. [ 4.014058] Freeing init memory: 1036K /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: /dev/nvramNo such file or directory: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: /dev/nvramNo such file or directory: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram/dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory : No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory /dev/nvram: No such file or directory - preinit - Press the [f] key and hit [enter] to enter failsafe mode - regular preinit - [ 11.211027] UBIFS: recovery needed [ 11.414464] UBIFS: recovery completed [ 11.417088] UBIFS: mounted UBI device 0, volume 2, name “ubi_rootfs_data” [ 11.423867] UBIFS: file system size: 30220288 bytes (29512 KiB, 28 MiB, 238 LEBs) [ 11.431490] UBIFS: journal size: 1523712 bytes (1488 KiB, 1 MiB, 12 LEBs) [ 11.438800] UBIFS: media format: w4/r0 (latest is w4/r0) [ 11.444579] UBIFS: default compressor: lzo [ 11.448672] UBIFS: reserved for root: 1427378 bytes (1393 KiB) switching to jffs2 - init - cmd=[touch /tmp/var/lib/nfs/xtab ] cmd=[chmod 644 /tmp/var/lib/nfs/xtab ] cmd=[touch /tmp/var/lib/nfs/etab ] cmd=[chmod 644 /tmp/var/lib/nfs/etab ] cmd=[touch /tmp/var/lib/nfs/rmtab ] cmd=[chmod 644 /tmp/var/lib/nfs/rmtab ] cmd=[touch /tmp/var/lib/nfs/state ] cmd=[chmod go-rwx /tmp/var/lib/nfs/state ] cmd=[touch /tmp/disk_updating_lock ] cmd=[chmod 644 /tmp/disk_u�md=[chmod 644 /tmp/file_variable_updating_lock ] pre_sysinit: Setup console The boot is UNKNOWN The boot is UNKNOWN /bin/sh: can't create /dev/: Is a directory Restoring Storage Nvram Defaults disk(0, 0) execute /etc/init.d/boot start [ 12.864323] ssdk_plat_init start [ 12.866541] Register QCA PHY driver [ 13.720524] qca-ssdk module init succeeded! [ 14.241611] usbcore: registered new interface driver usbfs [ 14.246141] usbcore: registered new interface driver hub [ 14.251452] usbcore: registered new device driver usb [ 14.429865] md: linear personality registered for level -1 [ 14.443392] md: raid0 personality registered for level 0 [ 14.457075] md: raid1 personality registered for level 1 [ 14.470571] Button Hotplug driver version 0.4.1 [ 14.840331] NTFS driver 2.1.30 [Flags: R/O MODULE]. [ 15.169728] nss_driver - fw of size 321792 bytes copied to load addr: 40000000 [ 15.194064] nss_driver - Turbo Support 1 [ 15.198375] bf22f994: NSS Shaping is enabled, handler id: 0 [ 15.241674] nss_driver - fw of size 3568 bytes copied to load addr: 40800000 [ 15.249578] Error - Duplicate Interface CB Registered for interface 51 [ 15.383630] L2TP core driver, V2.0 [ 15.395501] L2TP netlink interface [ 15.408028] nss_gmac: [ 15.414401] nss_gmac: * Driver :NSS GMAC Driver for RTL v(3.72a) [ 15.420649] nss_gmac: * Version :1.0 [ 15.424367] nss_gmac: * Copyright :Copyright © 2013 The Linux Foundation. All rights reserved. [ 15.433177] nss_gmac: [ 15.441018] nss_gmac: GMAC1(dd4b14c0) Invalid MAC@ - using de:df:e0:e1:e2:e3 [ 15.453639] nss_gmac: GMAC2(dd4b2cc0) Invalid MAC@ - using be:bf:c0:c1:c2:c3 [ 16.528803] nss_macsec init success [ 16.700812] asf: module license 'Proprietary' taints kernel. [ 16.705435] Disabling lock debugging due to kernel taint [ 16.721399] Address of trace_timer :bf28935c [ 16.955014] ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D) [ 16.972696] ath_rate_atheros: Copyright © 2001-2005 Atheros Communications, Inc, All Rights Reserved [ 16.990909] ath_dfs: Version 2.0.0 [ 16.990909] Copyright © 2005-2006 Atheros Communications, Inc. All Rights Reserved [ 17.035395] ath_spectral: Version 2.0.0 [ 17.035426] Copyright © 2005-2009 Atheros Communications, Inc. All Rights Reserved [ 17.045954] SPECTRAL module built on Sep 28 2018 19:40:04 [ 17.060980] ath_tx99: Version 2.0 [ 17.060980] Copyright © 2010 Atheros Communications, Inc, All Rights Reserved [ 17.247828] ath_dev: Copyright © 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 18.526366] ath_pci: 10.2.2.60.17 (Atheros/multi-bss) [ 18.530459] ath_pci_probe [ 18.532989] PCI device id is 003c :003c [ 18.536832] PCI: enabling device 0000:03:00.0 (0140 → 0142) [ 18.542767] ath_pci 0000:03:00.0: ath DEBUG: sc=0xdd3fa600 [ 18.547922] [ 18.547922] ol_ath_pci_configure : num_desired MSI set to 0 [ 18.555076] [ 18.555076] Using PCI Legacy Interrupt [ 19.558450] CE_per_engine_handler_adjust, base=dd3fa600 offset=57400 [ 19.563886] CE_per_engine_handler_adjust, base=dd3fa600 offset=57800 [ 19.580662] ol_ath_attach: ath_attach TODO [ 19.583911] ol_ath_attach 1272 host_enable 1 [ 19.588409] ol_ath_attach: dev name wifi0 [ 19.592502] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) [ 19.601905] OL_ACBKMinfree : 0 [ 19.604998] OL_ACBEMinfree : 0 [ 19.608153] OL_ACVIMinfree : 0 [ 19.611246] OL_ACVOMinfree : 0 [ 19.614370] ol_ath_attach() BMI inited. [ 19.618338] ol_ath_attach() BMI Get Target Info. [ 19.622805] ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c [ 19.628397] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 19.633833] ol_ath_attach() configure Target . [ 19.638175] ol_transfer_bin_file 1787: Download Board data len 2116 [ 19.648578] ol_ath_download_firmware: Using 0x1234 for the remainder of init [ 19.654607] ol_transfer_bin_file 1779: Download OTP data len 7208 [ 19.745485] ol_transfer_bin_file 1825: Download Firmware data len 229488 [ 20.736769] ol_ath_attach() Download FW. [ 20.739800] ol_ath_attach() HT Create . [ 20.743580] ol_ath_attach() HIF Claim. [ 20.747422] ol_ath_attach() BMI Done. [ 20.751077] ol_ath_attach() WMI attached. wmi_handle db080000 [ 20.756857] +HWT [ 20.758700] SOC_RESET_CONTROL_ADDRESS : 800 [ 20.762855] CPU_INTR_ADDRESS = [0] [ 20.766229] SOC_GLOBAL_RESET_ADDRESS = [0] [ 20.770321] Rx_Filter : [0] [ 20.773102] CE_per_engine_handler_adjust, base=dd3fa600 offset=57400 [ 20.779537] CE_per_engine_handler_adjust, base=dd3fa600 offset=57800 [ 20.785973] CE_per_engine_handler_adjust, base=dd3fa600 offset=57c00 [ 20.792408] CE_per_engine_handler_adjust, base=dd3fa600 offset=58000 [ 20.798812] CE_per_engine_handler_adjust, base=dd3fa600 offset=58400 [ 20.805310] CE_per_engine_handler_adjust, base=dd3fa600 offset=58800 [ 20.814151] CE_recv_buf_enqueue 653 Populate last entry 512 for CE 5 [ 20.819462] CE_recv_buf_enqueue 662 CE 5 wi 511 dest_ptr 0x5b838040 nbytes 0 recv_ctxt 0xdb16e900 [ 20.828366] -HWT [ 20.830240] HTC Service:0x0300 ep:1 TX flow control disabled [ 20.837082] CE_pkt_dl_len_set CE 4 Pkt download length 64 [ 20.841549] ol_txrx_pdev_attach: 1424 tx desc's allocated ; range starts from d9f20000 [ 20.849640] HTC Service:0x0100 ep:2 TX flow control disabled [ 20.855826] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 20.861761] num_rf_chain : 00000003 [ 20.865229] ht_cap_info: : 0000085b [ 20.868697] vht_cap_info : 338001b2 [ 20.872164] vht_supp_mcs : 0000ffea [ 20.875632] LARGE_AP enabled. num_peers 144, num_vdevs 16, num_tids 256 [ 20.882255] idx 0 req 1 num_units 0 num_unit_info 2 unit size 444 actual units 145 [ 20.890003] chunk 0 len 64380 requested ,ptr 0x5b4a0000 [ 20.904342] FIRMWARE:P 145 V 16 T 443 [ 20.904342] [ 20.908528] FIRMWARE:_wlan_rtt_enable [ 20.914401] wmi_ready_event_rx: WMI UNIFIED READY event [ 20.918837] ol_ath_connect_htc() WMI is ready [ 20.923117] ol_ath_set_host_app_area TODO [ 20.927147] target uses HTT version 2.1; host uses 2.1 [ 20.936301] ol_ath_attach() connect HTC. [ 20.939300] bypasswmi : 0 [ 20.941861] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 20.953733] ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 [ 20.960481] ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 [ 20.967228] ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 [ 20.974039] ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 [ 20.980880] ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 [ 20.988097] ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 [ 20.995282] ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 [ 21.002561] ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 [ 21.009965] ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 [ 21.017338] ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 [ 21.024711] ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 [ 21.032271] ol_ath_phyerr_attach: called [ 21.036176] OL Resmgr Init-ed [ 21.039081] ol_if_spectral_setup [ 21.042236] SPECTRAL : get_capability not registered [ 21.047203] HAL_CAP_PHYDIAG : Capable [ 21.050859] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231) [ 21.058919] SPECTRAL : get_capability not registered [ 21.063917] HAL_CAP_RADAR : Capable [ 21.067510] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 21.067510] (spectral_attach : 236) [ 21.077319] SPECTRAL : get_capability not registered [ 21.082286] HAL_CAP_SPECTRAL_SCAN : Capable [ 21.086410] SPECTRAL : get_tsf64 not registered [ 21.090971] spectral_init_netlink 52 NULL SKB [ 21.095282] Green-AP : Green-AP : Attached [ 21.095282] [ 21.100843] Green-AP : Attached [ 21.104029] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. [ 21.111184] ol_if_dfs_setup: called [ 21.114745] ol_if_dfs_attach: called; ptr=daf81984, radar_info=db6dfbd0 [ 21.121649] ol_ath_rtt_meas_report_attach: called [ 21.126148] ol_ath_attach() UMAC attach . [ 21.130115] ol_if_dfs_configure: called [ 21.133895] ol_if_dfs_configure: FCC domain [ 21.138113] ol_if_dfs_disable: called [ 21.141768] ol_ath_attach: Calling ol_if_dfs_configure [ 21.146860] ol_ath_attach: init tx/rx TODO [ 21.151109] ol_ath_attach: hard_header_len reservation 58 [ 21.167478] Initializing Pktlogs for 11ac [ 21.180037] sa_init_module [ 21.307528] bonding: Ethernet Channel Bonding Driver: v3.7.1 (April 27, 2011) [ 21.582474] ip_tables: (C) 2000-2006 Netfilter Core Team [ 21.751327] [wifi0] FWLOG: [21079] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x460, 0x460, 0x0 ) [ 21.758887] [wifi0] FWLOG: [21079] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x460, 0x460, 0x0 ) [ 21.767572] [wifi0] FWLOG: [21079] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x460, 0x460, 0x0 ) [ 21.776288] [wifi0] FWLOG: [21079] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x460, 0x460, 0x0 ) [ 21.784942] [wifi0] FWLOG: [21084] WHAL_ERROR_RECV_STOPPCU ( 0x110298a, 0x3 ) [ 21.792064] [wifi0] FWLOG: [21084] WHAL_ERROR_RESET_PM ( ) [ 21.831740] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 21.837519] msm_hsusb_host msm_hsusb_host: unable to find transceiver [ 21.875788] nf_conntrack version 0.5.0 (7620 buckets, 30480 max) [ 22.004404] PPPoL2TP kernel driver, V2.0 [ 22.212589] hahaha init ipt webstr module... [ 22.309809] xt_time: kernel timezone is -0000 [ 22.657731] nf_conntrack_rtsp v0.6.21 loading [ 22.670915] nf_nat_rtsp v0.6.21 loading [ 22.703530] [cbt_tcp_init]: init tcp module .. [ 22.706935] [init]: tcp_init ok [ 22.710090] [dns_init]: init dns module .. [ 22.714151] [init]: dns_init ok [ 22.717307] [pct_init]: init pct module .. [ 22.721368] [init]: pct_init ok [ 22.724492] [pct6_init]: init pct module .. [ 22.728647] [init]: pct6_init ok [ 22.731865] [ssl_init]: init ssl module .. [ 22.735926] [init]: ssl_init ok [ 22.739237] [ssl6_init]: init ssl module .. [ 22.743236] [init]: ssl6_init ok [ 22.795907] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 22.991596] ipq-dwc3 ipq-dwc3.0: unable to read platform data num of dbm eps [ 23.098313] xhci-hcd xhci-hcd.0: xHCI Host Controller [ 23.102436] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 1 [ 23.109715] xhci-hcd xhci-hcd.0: irq 142, io mem 0x11000000 [ 23.115463] usb_set_configuration: has interfaces 1 [ 23.120087] usb_device_match: usb driver name usbfs, busnum 1 [ 23.125710] usb_device_match: usb driver name hub, busnum 1 [ 23.131302] hub 1-0:1.0: USB hub found [ 23.135020] hub 1-0:1.0: 1 port detected [ 23.139144] xhci-hcd xhci-hcd.0: xHCI Host Controller [ 23.143955] xhci-hcd xhci-hcd.0: new USB bus registered, assigned bus number 2 [ 23.151452] usb_set_configuration: has interfaces 1 [ 23.156107] usb_device_match: usb driver name usbfs, busnum 2 [ 23.161824] usb_device_match: usb driver name hub, busnum 2 [ 23.167291] hub 2-0:1.0: USB hub found [ 23.171040] hub 2-0:1.0: 1 port detected [ 23.176726] ipq-dwc3 ipq-dwc3.1: unable to read platform data num of dbm eps [ 23.283380] xhci-hcd xhci-hcd.1: xHCI Host Controller [ 23.287441] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 3 [ 23.294720] xhci-hcd xhci-hcd.1: irq 237, io mem 0x10000000 [ 23.300531] usb_set_configuration: has interfaces 1 [ 23.305154] usb_device_match: usb driver name usbfs, busnum 3 [ 23.310777] usb_device_match: usb driver name hub, busnum 3 [ 23.316338] hub 3-0:1.0: USB hub found [ 23.320087] hub 3-0:1.0: 1 port detected [ 23.324211] xhci-hcd xhci-hcd.1: xHCI Host Controller [ 23.329084] xhci-hcd xhci-hcd.1: new USB bus registered, assigned bus number 4 [ 23.336488] usb_set_configuration: has interfaces 1 [ 23.341205] usb_device_match: usb driver name usbfs, busnum 4 [ 23.346797] usb_device_match: usb driver name hub, busnum 4 [ 23.352389] hub 4-0:1.0: USB hub found [ 23.356138] hub 4-0:1.0: 1 port detected [ 23.438081] hub 1-0:1.0: unable to enumerate USB device on port 1 [ 23.566416] Initializing USB Mass Storage driver... [ 23.570540] usb_device_match: usb driver name usb-storage, busnum 1 [ 23.576538] usb_device_match: usb driver name usb-storage, busnum 2 [ 23.582786] usb_device_match: usb driver name usb-storage, busnum 3 [ 23.589065] usb_device_match: usb driver name usb-storage, busnum 4 [ 23.595720] usbcore: registered new interface driver usb-storage [ 23.601280] USB Mass Storage support registered. [ 23.624773] sxuptp_devfilter: Unknown symbol sxuptp_deregister_interface_probe (err 0) [ 23.631708] sxuptp_devfilter: Unknown symbol sxuptp_procfs_get_dir_entry (err 0) [ 23.639112] sxuptp_devfilter: Unknown symbol sxuptp_register_interface_probe (err 0) [ 23.669603] usb_device_match: usb driver name sxuptp_driver, busnum 1 [ 23.675007] usb_device_match: usb driver name sxuptp_driver, busnum 2 [ 23.718119] usb 2-1: new SuperSpeed USB device number 2 using xhci-hcd [ 23.739550] usb_set_configuration: has interfaces 1 [ 23.743486] usb_device_match: usb driver name usbfs, busnum 2 [ 23.749140] usb_device_match: usb driver name hub, busnum 2 [ 23.754670] usb_device_match: usb driver name usb-storage, busnum 2 [ 23.761168] scsi1 : usb-storage 2-1:1.0 [ 23.765167] usb_device_match: usb driver name sxuptp_driver, busnum 3 [ 23.771290] usb_device_match: usb driver name sxuptp_driver, busnum 4 [ 23.777600] usb_device_match: usb driver name sxuptp_driver, busnum 2 [ 23.784129] usbcore: registered new interface driver sxuptp_driver [ 23.821774] fuse init (API version 7.18) [ 23.943111] u32 classifier [ 23.944767] Performance counters on [ 23.948609] input device check on [ 23.952233] Actions configured [ 24.089597] ECM init [ 24.093345] ECM init complete [ 24.758481] scsi 1:0:0:0: Direct-Access SanDisk Ultra Fit 1.00 PQ: 0 ANSI: 6 [ 24.766198] sd 1:0:0:0: [sda] 30375936 512-byte logical blocks: (15.5 GB/14.4 GiB) [ 24.774414] sd 1:0:0:0: [sda] Write Protect is off [ 24.778600] sd 1:0:0:0: [sda] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA [ 24.790346] sda: sda1 sda2 sda3 [ 24.794220] sd 1:0:0:0: [sda] Attached SCSI removable disk /etc/rc.common: line 85: /sbin/sound: Permission denied cmd=[insmod /lib/jnl.ko ] [ 25.550234] jnl: driver (lke_8.9.0 lke_8.9.0_r227163_b16, LBD=ON) loaded at bf992000 cmd=[insmod /lib/ufsd.ko ] [ 25.897750] ufsd:: trace mask set to 0000000f [ 25.901093] ufsd: driver (lke_8.9.0 lke_8.9.0_r227163_b16, LBD=ON, delalloc, ioctl, bdi, sd(1), fua, tr) loaded at bf99e000 [ 25.901093] NTFS support included [ 25.901093] Hfs+/HfsJ support included [ 25.901124] optimized: speed [ 25.901124] Build_forBelkin_Linksys_AC2350_k3.4.0_2014-04-16_lke_8.9.0_r227163_b16 [ 25.901124] Hit enter to continue...The chipset is IPQ806x... ##### fw_md5sum == f29838904cdde98b57e9fda0e9329b76 ##### cmd=[killall httpd ] killall: httpd: no process killed killall: check_http.sh: no process killed cmd=[killall gn-httpd ] killall: gn-httpd: no process killed cmd=[killall gn-httpd ] killall: gn-httpd: no process killed cmd=[killall wm-httpd ] killall: wm-httpd: no process killed [ 28.099062] [wp_unhook]: hook already unregistered cmd=[resetbutton ] WARNING: console log level set to 1 system /etc/init.d/network start signalling TIMER cmd=[brctl addbr br0 ] name=[eth1] lan_ifname=[br0] cmd=[brctl addif br0 eth1 ] [ 31.284817] device eth1 entered promiscuous mode [ 31.292127] ADDRCONF(NETDEV_UP): eth1: link is not ready ====⇒ set br0 hwaddr to B4:75:0E:C0:03:6B [ 31.297563] ADDRCONF(NETDEV_UP): br0: link is not ready Set 1 to /proc/sys/net/ipv4/conf/default/arp_ignore ... Set 1 to /proc/sys/net/ipv4/conf/all/arp_ignore ... Set 1 to /proc/sys/net/ipv4/ip_forward ... Set 1 to /proc/sys/net/ipv4/icmp_echo_ignore_broadcasts ... Set 1 to /proc/sys/net/ipv4/icmp_ignore_bogus_error_responses ... Set 0 to /proc/sys/net/ipv4/tcp_ecn ... Set 30 to /proc/sys/net/ipv4/tcp_fin_timeout ... Set 120 to /proc/sys/net/ipv4/tcp_keepalive_time ... Set 1 to /proc/sys/net/ipv4/tcp_syncookies ... Set 1 to /proc/sys/net/ipv4/tcp_timestamps ... Set 1 to /proc/sys/net/ipv4/tcp_sack ... Set 1 to /proc/sys/net/ipv4/tcp_dsack ... Set 1 to /proc/sys/net/netfilter/nf_conntrack_acct ... Set 0 to /proc/sys/net/netfilter/nf_conntrack_checksum ... Set 16384 to /proc/sys/net/netfilter/nf_conntrack_max ... Set 3600 to /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established ... Set 60 to /proc/sys/net/netfilter/nf_conntrack_udp_timeout ... Set 180 to /proc/sys/net/netfilter/nf_conntrack_udp_timeout_stream ... Set 0 to /proc/sys/net/bridge/bridge-nf-call-arptables ... Set 1 to /proc/sys/net/bridge/bridge-nf-call-iptables ... Set 1 to /proc/sys/net/bridge/bridge-nf-call-ip6tables ... Set 1 to /proc/sys/dev/nss/general/redirect ... lo: File exists Set 66560 to /proc/sys/net/core/rmem_max ... uci: Entry not found Del guest wlan settings: uci delete wireless.@wifi-iface[1] uci: Entry not found uci: Entry not found [ 31.540299] sa_exit_module [ 31.547735] Suspending Target - with disable_intr set :wifi0 (sc dd3fa600) [ 31.553639] waiting for target paused event from target :wifi0 (sc dd3fa600) [ 31.617994] ol_ath_detach: init tx/rx cleanup TODO [ 31.621993] ol_if_dfs_teardown: called [ 31.625898] ol_ath_phyerr_detach: called [ 31.630959] CE_fini 2204 Cleaning up HTT Tx CE [ 31.634395] CE_fini Cleaning up HTT MSG CE(5) [ 31.641768] ol_if_spectral_detach [ 31.644079] SPECTRAL : Module removed (spectral = d9fc2000) [ 31.649890] Green-AP : Green-AP : Detached [ 31.649890] [ 31.655201] Green-AP : Detached [ 31.658356] ath_pci_warm_reset :(sc dd3fa600) [ 31.662667] Target Warm Reset [ 31.665604] Host Intr Cause reg 0x900c : value : 0x4000 [ 31.670884] Target CPU Intr Cause 0x5040 [ 31.774820] addr 0x4050 : 0x4 [ 31.796938] Target CPU Intr Cause after CE reset 0x40 [ 31.801093] RESET_CONTROL after cpu warm reset 0x804 [ 31.906154] Target Warm reset complete [ 31.908997] ath_pci_remove [ 31.911683] ath_pci: driver unloaded [ 31.918619] Removing athdebug proc file [ 31.921462] ath_dev: driver unloaded [ 31.927897] ath_tx99: driver unloaded [ 31.933270] ath_spectral: driver unloaded [ 31.939019] ath_dfs: driver unloaded [ 31.944329] ath_rate_atheros: driver unloaded [ 31.950484] ath_hal: driver unloaded [ 32.006373] Address of trace_timer :bfa4035c [ 32.024273] ath_hal: 0.9.17.1 (AR5416, AR9380, WRITE_EEPROM, TX_DATA_SWAP, RX_DATA_SWAP, 11D) [ 32.043236] ath_rate_atheros: Copyright © 2001-2005 Atheros Communications, Inc, All Rights Reserved [ 32.062417] ath_dfs: Version 2.0.0 [ 32.062417] Copyright © 2005-2006 Atheros Communications, Inc. All Rights Reserved [ 32.083442] ath_spectral: Version 2.0.0 [ 32.083442] Copyright © 2005-2009 Atheros Communications, Inc. All Rights Reserved [ 32.094033] SPECTRAL module built on Sep 28 2018 19:40:04 [ 32.109465] ath_tx99: Version 2.0 [ 32.109465] Copyright © 2010 Atheros Communications, Inc, All Rights Reserved [ 32.135238] ath_dev: Copyright © 2001-2007 Atheros Communications, Inc, All Rights Reserved [ 32.169103] ath_pci: 10.2.2.60.17 (Atheros/multi-bss) [ 32.173164] ath_pci_probe [ 32.175726] PCI device id is 003c :003c [ 32.179881] ath_pci 0000:03:00.0: ath DEBUG: sc=0xdd3fae00 [ 32.185035] [ 32.185035] ol_ath_pci_configure : num_desired MSI set to 0 [ 32.192189] [ 32.192189] Using PCI Legacy Interrupt [ 33.188441] CE_per_engine_handler_adjust, base=dd3fae00 offset=57400 [ 33.193876] CE_per_engine_handler_adjust, base=dd3fae00 offset=57800 [ 33.212339] ol_ath_attach: ath_attach TODO [ 33.215588] ol_ath_attach 1272 host_enable 1 [ 33.220024] ol_ath_attach: dev name wifi0 [ 33.224179] ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) [ 33.233583] OL_ACBKMinfree : 0 [ 33.236676] OL_ACBEMinfree : 0 [ 33.239800] OL_ACVIMinfree : 0 [ 33.242924] OL_ACVOMinfree : 0 [ 33.246048] ol_ath_attach() BMI inited. [ 33.255014] ol_ath_attach() BMI Get Target Info. [ 33.258606] ol_ath_attach() TARGET TYPE: 7 Vers 0x4100016c [ 33.264198] NUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0 [ 33.270571] ol_ath_attach() configure Target . [ 33.274101] ol_transfer_bin_file 1787: Download Board data len 2116 [ 33.284879] ol_ath_download_firmware: Using 0x1234 for the remainder of init [ 33.290909] ol_transfer_bin_file 1779: Download OTP data len 7208 [ 33.297813] br0: port 1(eth1) entered forwarding state [ 33.302124] br0: port 1(eth1) entered forwarding state [ 33.307310] ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 33.313089] ADDRCONF(NETDEV_CHANGE): br0: link becomes ready [ 33.443423] ol_transfer_bin_file 1825: Download Firmware data len 229488 [ 34.474945] ol_ath_attach() Download FW. [ 34.478069] ol_ath_attach() HT Create . [ 34.481755] ol_ath_attach() HIF Claim. [ 34.485723] ol_ath_attach() BMI Done. [ 34.489253] ol_ath_attach() WMI attached. wmi_handle d9fa0000 [ 34.495032] +HWT [ 34.496844] SOC_RESET_CONTROL_ADDRESS : 800 [ 34.501030] CPU_INTR_ADDRESS = [0] [ 34.504373] SOC_GLOBAL_RESET_ADDRESS = [0] [ 34.508497] Rx_Filter : [80200] [ 34.511590] CE_per_engine_handler_adjust, base=dd3fae00 offset=57400 [ 34.518056] CE_per_engine_handler_adjust, base=dd3fae00 offset=57800 [ 34.525898] CE_per_engine_handler_adjust, base=dd3fae00 offset=57c00 [ 34.531365] CE_per_engine_handler_adjust, base=dd3fae00 offset=58000 [ 34.537769] CE_per_engine_handler_adjust, base=dd3fae00 offset=58400 [ 34.544298] CE_per_engine_handler_adjust, base=dd3fae00 offset=58800 [ 34.552671] CE_recv_buf_enqueue 653 Populate last entry 512 for CE 5 [ 34.558013] CE_recv_buf_enqueue 662 CE 5 wi 511 dest_ptr 0x5c41d040 nbytes 0 recv_ctxt 0xd9b5ce40 [ 34.566885] -HWT [ 34.568791] HTC Service:0x0300 ep:1 TX flow control disabled [ 34.575757] CE_pkt_dl_len_set CE 4 Pkt download length 64 [ 34.580162] ol_txrx_pdev_attach: 1424 tx desc's allocated ; range starts from da370000 [ 34.588316] HTC Service:0x0100 ep:2 TX flow control disabled [ 34.594376] wmi_service_ready_event_rx: WMI UNIFIED SERVICE READY event [ 34.600437] num_rf_chain : 00000003 [ 34.603873] ht_cap_info: : 0000085b [ 34.607341] vht_cap_info : 338001b2 [ 34.610840] vht_supp_mcs : 0000ffea [ 34.614308] LARGE_AP enabled. num_peers 144, num_vdevs 16, num_tids 256 [ 34.620930] idx 0 req 1 num_units 0 num_unit_info 2 unit size 444 actual units 145 [ 34.628678] chunk 0 len 64380 requested ,ptr 0x5b880000 [ 34.642986] FIRMWARE:P 145 V 16 T 443 [ 34.642986] [ 34.647203] FIRMWARE:_wlan_rtt_enable [ 34.653077] wmi_ready_event_rx: WMI UNIFIED READY event [ 34.657513] ol_ath_connect_htc() WMI is ready [ 34.661824] ol_ath_set_host_app_area TODO [ 34.665854] target uses HTT version 2.1; host uses 2.1 [ 34.675039] ol_ath_attach() connect HTC. [ 34.678038] bypasswmi : 0 [ 34.680631] ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0. [ 34.692408] ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 [ 34.699218] ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 [ 34.705966] ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 [ 34.712808] ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 [ 34.719618] ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 [ 34.726866] ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 [ 34.734020] ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 [ 34.741362] ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 [ 34.748703] ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 [ 34.756044] ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 [ 34.763480] ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 [ 34.771009] ol_ath_phyerr_attach: called [ 34.774882] OL Resmgr Init-ed [ 34.777881] ol_if_spectral_setup [ 34.781005] SPECTRAL : get_capability not registered [ 34.785910] HAL_CAP_PHYDIAG : Capable [ 34.789597] SPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 231) [ 34.797625] SPECTRAL : get_capability not registered [ 34.802592] HAL_CAP_RADAR : Capable [ 34.806216] SPECTRAL : Need to fix the capablity check for SPECTRAL [ 34.806216] (spectral_attach : 236) [ 34.816057] SPECTRAL : get_capability not registered [ 34.820993] HAL_CAP_SPECTRAL_SCAN : Capable [ 34.825148] SPECTRAL : get_tsf64 not registered [ 34.829709] spectral_init_netlink 52 NULL SKB [ 34.833989] Green-AP : Green-AP : Attached [ 34.834020] [ 34.839612] Green-AP : Attached [ 34.842705] ol_ath_smart_ant_attach: Hardware doest not support Smart Antenna. [ 34.849921] ol_if_dfs_setup: called [ 34.853452] ol_if_dfs_attach: called; ptr=daf0d984, radar_info=db6bbbd0 [ 34.860637] ol_ath_rtt_meas_report_attach: called [ 34.864885] ol_ath_attach() UMAC attach . [ 34.868822] ol_if_dfs_configure: called [ 34.872633] ol_if_dfs_configure: FCC domain [ 34.876788] ol_if_dfs_disable: called [ 34.880506] ol_ath_attach: Calling ol_if_dfs_configure [ 34.885567] ol_ath_attach: init tx/rx TODO [ 34.889846] ol_ath_attach: hard_header_len reservation 58 [ 34.906529] Initializing Pktlogs for 11ac [ 34.919650] sa_init_module [ 35.044392] [ol_ath_iw_setcountry][1438] *p=47, *(p+1)=42 [ 35.048797] isCountryCodeValid: EEPROM regdomain 0x0 [ 35.053701] ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150 [ 35.060574] ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140 [ 35.067353] ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0 [ 35.074133] ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150 [ 35.080974] ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100 [ 35.088191] ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100 [ 35.095376] ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100 [ 35.102686] ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100 [ 35.110059] ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100 [ 35.117400] ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100 [ 35.124804] ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100 [ 35.198937] ath_ioctl: SIOC80211IFCREATE CALLED [ 35.202467] wmi_unified_vdev_create_send: ID = 0 VAP Addr = b4:75:0e:c0:03:6d: [ 35.209746] Setting dscp for vap id: 0 [ 35.213402] ieee80211_smart_ant_init: Smart Antenna is not supported [ 35.219993] VAP device ath0 created osifp: (da236cc0) os_if: (daf70000) [ 35.234457] Set freq vap stop send + daf70000 [ 35.237769] OL vap_stop + [ 35.240424] wmi_unified_vdev_stop_send for vap 0 (d9fa0000) [ 35.245985] OL vap_stop - [ 35.248578] STOPPED EVENT for vap 0 (d9fa0000) [ 35.253108] Set freq vap stop send -daf70000 [ 35.378975] Set wait done --daf70000 [ 35.396376] ol_ath_wmm_update: [ 35.414214] [ 35.414214] DES SSID SET= [ 35.420118] [ 35.420118] DES SSID SET=Linksys07450 [ 35.443767] OL vap_stop + [ 35.445392] wmi_unified_vdev_stop_send for vap 0 (d9fa0000) [ 35.451171] STOPPED EVENT for vap 0 (d9fa0000) [ 35.455357] OL vap_stop - [ 35.489440] [wifi0] FWLOG: [35146] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x460, 0x460, 0x0 ) [ 35.497000] [wifi0] FWLOG: [35146] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x460, 0x460, 0x0 ) [ 35.505685] [wifi0] FWLOG: [35146] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x460, 0x460, 0x0 ) [ 35.514370] [wifi0] FWLOG: [35146] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x460, 0x460, 0x0 ) [ 35.523055] [wifi0] FWLOG: [35152] WHAL_ERROR_RECV_STOPPCU ( 0x110298a, 0x3 ) [ 35.530178] [wifi0] FWLOG: [35152] WHAL_ERROR_RESET_PM ( ) [ 35.589065] wmi_unified_scan_start_send for vap 0 (d9fa0000) [ 35.594001] 8021q: adding VLAN 0 to HW filter on device ath0 /sbin/wifi: eval: line 1: ubus: not found /sbin/wifi: eval: line 1: ubus: not found /sbin/wifi: eval: line 1: ubus: not found /sbin/wifi: eval: line 1: ubus: not found /sbin/wifi: eval: line 1: ubus: not found /sbin/wifi: eval: line 1: ubus: not found /sbin/wifi: eval: line 1: ubus: not found /sbin/wifi: eval: line 1: ubus: not found Configuration file: /var/run/hostapd-ath0.conf [ 36.078006] ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 [ 36.084536] Scan in progress.. Cancelling it [ 36.088909] ol_scan_cancel for (d9fa0000) [ 36.093876] OL vap_stop + [ 36.095470] wmi_unified_vdev_stop_send for vap 0 (d9fa0000) [ 36.101062] OL vap_stop - [ 36.101093] STOPPED EVENT for vap 0 (d9fa0000) [ 36.148078] DEVICE IS DOWN ifname=ath0 [ 36.150952] DEVICE IS DOWN ifname=ath0 ath0: Could not connect to kernel driver [ 36.155201] OL vap_stop + [ 36.161012] wmi_unified_vdev_stop_send for vap 0 (d9fa0000) [ 36.166510] OL vap_stop - [ 36.166572] STOPPED EVENT for vap 0 (d9fa0000) Using interface ath0 with hwaddr b4:75:0e:c0:03:6d and ssid 'Linksys07450' WPS: Converting display to virtual_display for WPS 2.0 compliance WPS: Converting push_button to virtual_push_button for WPS 2.0 compliance hostapd_init_wps: config methods=2288 [ 36.299031] wmi_unified_scan_start_send for vap 0 (d9fa0000) [ 36.303842] 8021q: adding VLAN 0 to HW filter on device ath0 name=[ath0] lan_ifname=[br0] cmd=[brctl addif br0 ath0 ] [ 36.317900] device ath0 entered promiscuous mode [ 36.324586] br0: port 2(ath0) entered forwarding state [ 36.329209] br0: port 2(ath0) entered forwarding state
Get wireless 2.4G MAC: B4:75:0E:C0:03:6D
GN_MAC: mac B4:75:0E:C0:03:6D
GN_MAC: get GN mac B6:75:0E:C0:03:6D
[ 39.068978] osif_vap_init: Timeout waiting for vap to stop...returning
cmd=[insmod /lib/modules/3.4.0/qdpc-host.ko rx_pkt_align=1 use_nss=1 ]
[ 39.106779] parent cap:128, dev cap:256
[ 39.109621] Setting MPS to 128
[ 39.112652] PCI: enabling device 0000:01:00.0 (0144 → 0146)
[ 39.118431] PCIe MSI Interrupt Enabled
[ 39.121993] qdpc_map_sysctl_regs() Mapping sysctl
[ 39.126710] BAR:0 vaddr=0xe0a00000 busaddr=08000000 offset=0 len=65536
[ 39.133208] qdpc_map_epmem() Mapping epmem
[ 39.137269] BAR:2 vaddr=0xe0a20000 busaddr=08010000 offset=0 len=65536
[ 39.143798] qdpc_map_dma_regs() Mapping dma registers
[ 39.148828] BAR:3 vaddr=0xe0a40000 busaddr=08020000 offset=0 len=65536
[ 39.155326] qdpc-host version v36.7.3.23 Quantenna Communications Inc.
[ 39.161918] Tx Descriptor table: uncache virtual addr: 0xffda4000 paddr: 0x5b7f2000
[ 39.169478] Rx Descriptor table: uncache virtual addr: 0xffda45a0 paddr: 0x5b7f25a0
[ 39.177100] EP_handled_idx: uncache virtual addr: 0xffda51a0 paddr: 0x5b7f31a0
[ 39.185192] host0: Vmac Ethernet found
[ 39.188097] nss context created at 00000005
cmd=[ifconfig host0 up ]
Starting qtna wifi
done
cmd=[qtna_wifi.sh 0 10.254.254.253 ]
cmd=[tftpd -s /tmp -c -l -P 8350 ]
cmd=[cron ]
The boot is UNKNOWN
tftp server started
tftpd: standalone socket
[ 39.237956] PCI memory is little endian
[ 39.240737] EP map start addr : 0x00000000, Host memory start : 0x41500000
[ 39.247610] Setting HOST ready...
[ 39.297969] Requested DMA mask:0xffffffff
[ 39.300937] priv→pdev→mask:0xffffffff
[ 39.304748] set dma_mask = DMA_BIT_MASK(64):0xffffffffffffffff
[ 39.310621] EP FW load request...
[ 39.313870] Start download Firmware u-boot.bin...
cron: No such file or directory
cron: created
[HTTPD Starting on /www]
cmd=[httpd ]
[ 39.491815] device host0 entered promiscuous mode
[ 39.495532] br0: port 3(host0) entered forwarding state
[ 39.500718] br0: port 3(host0) entered forwarding state
waiting for QTN starting......
[ 39.558263] FW Data[0]: VA:0xe09ec000 PA:0x5a900000 Sz=68772..
[ 39.607966] done!
[ 39.657981] Image. Sz:68772 State:0xc
[ 39.660668] Image downloaded....!
[ 39.663917] Start booting EP...
[ 40.204873] OL vap_start +
[ 40.206529] wmi_unified_vdev_start_send for vap 0 (d9fa0000)
[ 40.212183] OL vap_start -
[ 40.218056] ol_vdev_start_resp_ev for vap 0 (d9fa0000)
[ 40.222180] ol_ath_vap_join: join operation is only for STA/IBSS mode
[ 40.228616] ol_ath_wmm_update:
[ 40.231677] wmi_unified_vdev_up_send for vap 0 (d9fa0000)
[ 40.237019] ieee80211_smart_ant_init: Smart Antenna is not supported
[ 40.243611] Notification to UMAC VAP layer
unknown sockaddr family on listen socket - 58336
cmd=[dnsmasq -h -i br0 -c 0 -r /tmp/resolv.conf ]
dnsmasq: unknown user or group: nobody
cmd=[route del -net 224.0.0.0 netmask 240.0.0.0 dev br0 ]
route: SIOCDELRT: No such process
cmd=[route add -net 224.0.0.0 netmask 240.0.0.0 dev br0 ]
cmd=[cesmDNS -o /tmp/.mdns_host_info -d -h Linksys07450 -l 192.168.1.1 ]
br0 192.168.1.100 86400
write_dhcpd_conf: file=/tmp/dhcpd-br0.conf, ifname=br0, lan_ip=lan_ipaddr lan_mask=lan_netmask
cmd=[dhcpd -cf /tmp/dhcpd-br0.conf -lf /tmp/dhcpd.leases -df /tmp/udhcpd.leases -pf /var/run/dhcpd.pid br0 ]
Internet Systems Consortium DHCP Server 4.1.1-P1
Copyright 2004-2010 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Wrote 0 leases to leases file.
Listening on Socket/br0/192.168.1.0/24
Sending on Socket/br0/192.168.1.0/24
cmd=[upnp -D -W eth0 ]
zebra disabled.
enter start_cifs...
read_disk_data: bus number=2
UPnP::upnp_device_attach:br0: attach InternetGatewayDevice.xml
ssdp byebye
UPnP::upnp_init:UPnP daemon is ready to run
Failed trying to open `/proc/sestat': No such file or directory
read_disk_data: bus number=2
Failed trying to open `/proc/sestat': No such file or directory
enter write_cifs_config_file...1
hahaha enter add_accounts...
add_accounts: buf=[admin:admin:admin:/:rw]
add_accounts: write=rw, basic_info[0]=admin, new_passwd=admin
cmd=[adduser -p admin admin -g root ]
addgroup: gid '0' in use
adduser: /tmp/ftproot/admin: No such file or directory
Changing password for admin
set new password over.
Password for admin changed by root
admin: eval /usr/sbin/smbadduser admin admin
cmd=[/usr/sbin/smbadduser admin admin ]
[ 42.857981] PCI memory is little endian
[ 42.860762] DMA offset : 0xbeb00000, no need to reset the value.
[ 42.866760] Setting HOST ready...
[ 42.917963] Requested DMA mask:0xffffffff
[ 42.920930] priv→pdev→mask:0xffffffff
[ 42.924742] set dma_mask = DMA_BIT_MASK(64):0xffffffffffffffff
[ 42.930584] EP FW load request...
[ 42.933864] Start download Firmware topaz-linux.lzma.img...
cmd=[adduser -p guest guest -g guest ]
adduser: /tmp/ftproot/guest: No such file or directory
Changing password for guest
set new password over.
Password for guest changed by root
cmd=[/usr/sbin/smbd -D ]
[ 48.327928] br0: port 1(eth1) entered forwarding state
cmd=[/usr/sbin/nmbd -D ]
read_disk_data: bus number=2
Failed trying to open `/proc/sestat': No such file or directory
read_disk_data: bus number=2
Failed trying to open `/proc/sestat': No such file or directory
enter write_cifs_config_file...1
hahaha enter add_accounts...
add_accounts: buf=[admin:admin:admin:/:rw]
add_accounts: write=rw, basic_info[0]=admin, new_passwd=admin
cmd=[adduser -p admin admin -g root ]
addgroup: gid '0' in use
adduser: /tmp/ftproot/admin: No such file or directory
Changing password for admin
set new password over.
Password for admin changed by root
admin: eval /usr/sbin/smbadduser admin admin
cmd=[/usr/sbin/smbadduser admin admin ]
[ 49.748890] FW Data[0]: VA:0xe2001000 PA:0x59b00000 Sz=1048576..
[ 49.797969] done!
[ 49.800000] FW Data[1]: VA:0xe2101000 PA:0x59b00000 Sz=1048576..
[ 49.847953] done!
[ 49.849671] FW Data[2]: VA:0xe2201000 PA:0x59b00000 Sz=1048576..
[ 49.897969] done!
[ 49.900000] FW Data[3]: VA:0xe2301000 PA:0x59b00000 Sz=1048576..
[ 49.947953] done!
[ 49.948890] FW Data[4]: VA:0xe2401000 PA:0x59b00000 Sz=49885..
[ 49.997969] done!
[ 50.047953] Image. Sz:4244189 State:0xc
[ 50.051671] Image downloaded....!
[ 50.054045] Start booting EP...
cmd=[adduser -p guest guest -g guest ]
adduser: /tmp/ftproot/guest: No such file or directory
Changing password for guest
set new password over.
Password for guest changed by root
cmd=[/usr/sbin/nmbd -D ]
Disk disconnected, don't start Twonky MediaServer
cmd=[killall -9 vsftpd ]
killall: vsftpd: no process killed
do not work
Enter into FTP root dir fail!It's not exist.
cmd=[/usr/sbin/jcpd ]
cmd=[nlinkd ]
[ 51.367947] br0: port 2(ath0) entered forwarding state
lltd:echo Linksys07450 > /proc/sys/kernel/hostname
LLTD: wireless interface argument is ath0.
cmd=[/sbin/monitor_cable ]
cmd=[/usr/sbin/arp -c ]
/usr/sbin/arp: No such file or directory
---- begin start_wan ----
[ 51.574289] ADDRCONF(NETDEV_UP): eth0: link is not ready
.... Begin monitor_cable: first wan link = 1
....cmd=[touch /tmp/hosts ]
start_dhcpc:=====( wan_or_lan=wan )=====
/usr/sbin/dhclient -nw -cf /tmp/dhcpc-wan.conf -sf /tmp/dhcpc -lf /tmp/dhcpc-wan.leases -pf /var/run/dhcpc-wan.pid eth0 &
cmd=[killall wan_auto_detect ]
killall: wan_auto_detect: no process killed
cmd=[/sbin/wan_auto_detect ]
start_wan_ipv6: [IPV6] eth0 dhcp
DEBUG, adapter index 9
DEBUG, adapter hardware address b4:75:0e:c0:03:6c
DEBUG, adapter index 9
DEBUG, adapter hardware address b4:75:0e:c0:03:6c
Send PPPoE PADI
Send 32 bytes
dhcpc_main,reason[PREINIT]
cmd=[touch /tmp/hosts ]
start_wan_ipv6: [IPV6] 0
TIMER
IDLE
Disk (8, 0) added.
read_disk_data: bus number=2
Failed trying to open `/proc/sestat': No such file or directory
The newly added disk is a foreign disk.
signalling USER1
mount_foreign_disk: dev name /dev/sda1 type_field=83
Unknown FileSystem
Logical sector size is zero.[ 52.934770] FAT-fs (sda1): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
mount_foreign_disk: dosfsck -s /dev/sda1 > /tmp/volume_label_0[ 52.946485] FAT-fs (sda1): bogus number of reserved sectors
[ 52.956888] FAT-fs (sda1): Can't find a valid FAT filesystem
pOrHo
mount_foreign_disk: try to mount by every filesystem.
mount_foreign_disk: mount result=-1
[ 53.009340] ufsd: failed to mount sda1
Failed to mount /dev/sda1 as type vfat: Invalid argument.
mount_foreign_disk: mount result=-1
Failed to mount /dev/sda1 as type ufsd: Invalid argument.
mount_foreign_disk: mount result=-1
Failed to mount /dev/sda1 as type iso9660: No such device.
Warning: Failing trying to mount a f[ 53.072164] FAT-fs (sda2): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
oreign share.
mount_foreign_disk: dev name /dev/sda2 type_field[ 53.088503] FAT-fs (sda2): bogus number of reserved sectors
[ 53.098812] FAT-fs (sda2): Can't find a valid FAT filesystem
=83
Unknown FileSystem
Logical sector size is zero.
mount_foreign_disk: dosfsck -s /dev/sda2 > /tmp/volume_label_JEx7DP
mount_foreign_disk: try to mount by every filesystem.
mount_foreign_disk: mount result=-1[ 53.149390] ufsd: failed to mount sda2
Failed to mount /dev/sda2 as type vfat: Invalid argument.
mount_foreign_disk: mount result=-1
Failed to mount /dev/sda2 as type ufsd: Invalid argument.
mount_foreign_disk: mount result=-1
Failed to mount /dev/sda2 as type iso9660: No such device.
Warning: Fa[ 53.221368] FAT-fs (sda3): utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
iling trying to mount a foreign share.
mount_foreign_disk: dev [ 53.236238] FAT-fs (sda3): bogus number of reserved sectors
[ 53.246672] FAT-fs (sda3): Can't find a valid FAT filesystem
name /dev/sda3 type_field=83
Unknown FileSystem
Logical sector size is zero.
mount_foreign_disk: dosfsck -s /dev/sda3 > /tmp/volume_label_VgjyRz
mount_foreign_disk: try to mount by every filesystem.
mount_foreign_disk: mount result=-1
[ 53.279662] ufsd: failed to mount sda3
Failed to mount /dev/sda3 as type vfat: Invalid argument.
mount_foreign_disk: mount result=-1
Failed to mount /dev/sda3 as type ufsd: Invalid argument.
mount_foreign_disk: mount result=-1
Failed to mount /dev/sda3 as type iso9660: No such device.
Warning: Failing trying to mount a foreign share.
mount_foreign_disk: mount disk over, begin to start services, mount_success=0
mount_foreign_disk: done!!!!
TIMER
IDLE
Restart service=[unplug_wan_cable]
stop_dhcp6c
cmd=[/usr/sbin/ip -6 addr flush dev eth0 scope global ]
cmd=[ip6tables -t filter -F ]
cmd=[ip6tables -t filter -Z ]
cmd=[ip6tables -t mangle -F ]
cmd=[ip6tables -t mangle -Z ]
Set 0 to /proc/sys/net/ipv6/conf/all/forwarding ...
delete tunnel 6rd failed: No such device
cmd=[killall -9 waninfo ]
stop_wan_ipv6: done
RTNETLINK answers: No such file or directory
/proc/sys/net/ctf/wan_mode: No such file or directory
cmd=[killall nlinkd ]
cmd=[killall -9 nlinkd ]
killall: nlinkd: no process killed
[ 53.620181] [hnd_unhook]: hook already unregistered
[ 53.626460] [hnd_unhook]: hook already unregistered
cmd=[killall -9 qos_bw_detect ]
killall: qos_bw_detect: no process killed
cmd=[killall igmprt ]
killall: igmprt: no process killed
cmd=[killall pppd ]
killall: pppd: no process killed
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall ip-up ]
killall: ip-up: no process killed
cmd=[killall ip-down ]
killall: ip-down: no process killed
cmd=[killall -15 pppd ]
killall: pppd: no process killed
[ 54.527928] br0: port 3(host0) entered forwarding state
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall -15 l2tpd ]
killall: l2tpd: no process killed
cmd=[killall -9 l2tpd ]
killall: l2tpd: no process killed
cmd=[killall -9 listen ]
killall: listen: no process killed
cmd=[killall -9 waninfo ]
killall: waninfo: no process killed
stop_dhcpc
cmd=[killall bpalogin ]
killall: bpalogin: no process killed
cmd=[killall -9 bpalogin ]
killall: bpalogin: no process killed
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall -9 pptp ]
killall: pptp: no process killed
cmd=[killall -9 ntpclient ]
killall: ntpclient: no process killed
cmd=[killall -9 redial ]
killall: redial: no process killed
cmd=[killall wan_auto_detect ]
IDLE
Hit enter to continue...Hit enter to continue...signalling USER1
Restart service=[wan_auto_detect]
stop_dhcp6c
cmd=[/usr/sbin/ip -6 addr flush dev eth0 scope global ]
cmd=[ip6tables -t filter -F ]
cmd=[ip6tables -t filter -Z ]
cmd=[ip6tables -t mangle -F ]
cmd=[ip6tables -t mangle -Z ]
Set 0 to /proc/sys/net/ipv6/conf/all/forwarding ...
delete tunnel 6rd failed: No such device
cmd=[killall -9 waninfo ]
killall: waninfo: no process killed
stop_wan_ipv6: done
/proc/sys/net/ctf/wan_mode: No such file or directory
cmd=[killall -9 nlinkd ]
killall: nlinkd: no process killed
[ 57.659137] [hnd_unhook]: hook already unregistered
[ 57.665417] [hnd_unhook]: hook already unregistered
cmd=[killall -9 qos_bw_detect ]
killall: qos_bw_detect: no process killed
cmd=[killall igmprt ]
killall: igmprt: no process killed
cmd=[killall pppd ]
killall: pppd: no process killed
[ 57.907966] EP boot successful, starting config...
[ 57.957981] Connection established with Target BBIC4 board
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall ip-up ]
killall: ip-up: no process killed
cmd=[killall ip-down ]
killall: ip-down: no process killed
cmd=[killall -15 pppd ]
killall: pppd: no process killed
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall -15 l2tpd ]
killall: l2tpd: no process killed
cmd=[killall -9 l2tpd ]
killall: l2tpd: no process killed
cmd=[killall -9 listen ]
killall: listen: no process killed
cmd=[killall -9 waninfo ]
killall: waninfo: no process killed
stop_dhcpc
cmd=[killall bpalogin ]
killall: bpalogin: no process killed
cmd=[killall -9 bpalogin ]
killall: bpalogin: no process killed
cmd=[killall -9 pppd ]
killall: pppd: no process killed
cmd=[killall -9 pptp ]
killall: pptp: no process killed
cmd=[killall -9 ntpclient ]
killall: ntpclient: no process killed
cmd=[killall -9 redial ]
killall: redial: no process killed
cmd=[killall wan_auto_detect ]
killall: wan_auto_detect: no process killed
[ 59.322086] ADDRCONF(NETDEV_UP): eth0: link is not ready
cmd=[touch /tmp/hosts ]
start_dhcpc:=====( wan_or_lan=wan )=====
/usr/sbin/dhclient -nw -cf /tmp/dhcpc-wan.conf -sf /tmp/dhcpc -lf /tmp/dhcpc-wan.leases -pf /var/run/dhcpc-wan.pid eth0 &
cmd=[killall wan_auto_detect ]
dhcpc_main,reason[PREINIT]
killall: wan_auto_detect: no process killed
cmd=[/sbin/wan_auto_detect ]
start_wan_ipv6: [IPV6] eth0 dhcp
DEBUG, adapter index 9
DEBUG, adapter hardware address b4:75:0e:c0:03:6c
DEBUG, adapter index 9
DEBUG, adapter hardware address b4:75:0e:c0:03:6c
Send PPPoE PADI
Send 32 bytes
cmd=[touch /tmp/hosts ]
cmd=[nlinkd ]
start_wan_ipv6: [IPV6] 0
IDLE
Hit enter to continue...[ 60.462480] nss_gmac: eth0 1000Mbps FullDuplex
[ 61.475757] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
4000001F
bit 0 - Ethernet interface
bit 1 - PCIE EP driver
bit 2 - PCIE RC driver
bit 3 - WiFi driver
bit 4 - Rpcd server
bit 30 - Calstate mode
bit 31 - System boot up completely
killall: qtna_state_check: no process killed
send pppoe
DEBUG, adapter index 9
DEBUG, adapter hardware address b4:75:0e:c0:03:6c
Send PPPoE PADI
Send 32 bytes
dhcpc_main,reason[BOUND]
bound: interface=eth0, new_ip_ipaddr=192.168.12.240
cmd=[killall -SIGUSR1 upnp ]
clear upnp entry
cmd=[touch /tmp/hosts ]
cmd=[killall -10 dhcpd ]
dhcpd pid is 7836848
cmd=[killall -10 gn-dhcpd ]
killall: gn-dhcpd: no process killed
cmd=[killall gn-dhcpd ]
killall: gn-dhcpd: no process killed
br0 192.168.1.100 86400
write_dhcpd_conf: file=/tmp/dhcpd-br0.conf, ifname=br0, lan_ip=lan_ipaddr lan_mask=lan_netmask
cmd=[dhcpd -cf /tmp/dhcpd-br0.conf -lf /tmp/dhcpd.leases -df /tmp/udhcpd.leases -pf /var/run/dhcpd.pid br0 ]
Internet Systems Consortium DHCP Server 4.1.1-P1
Copyright 2004-2010 Internet Systems Consortium.
All rights reserved.
For info, please visit https://www.isc.org/software/dhcp/
Wrote 0 leases to leases file.
Listening on Socket/br0/192.168.1.0/24
Sending on Socket/br0/192.168.1.0/24
There's already a DHCP server running. kill 2138
cmd=[killall dnsmasq ]
Hit enter to continue...killall: dnsmasq: no process killed
cmd=[dnsmasq -h -i br0 -c 0 -r /tmp/resolv.conf ]
Hit enter to continue...begin start_firewall.cmd=[iptables-restore /tmp/.ipt ]
Set 600 to /proc/sys/net/netfilter/nf_conntrack_tcp_timeout_established ...
Set 65 to /proc/sys/net/netfilter/nf_conntrack_udp_timeout ...
cmd=[killall -SIGUSR1 upnp ]
=====( auto detect - dhcp connected!! )=====
reset upnp entry
cmd=[killall igmprt ]
killall: igmprt: no process killed
Hit enter to continue...[ 68.432489] >> wlan igmp_snooping initial....
begin to start wan service!
[ 68.436551] >> wlan0 index 15 name:[ath0].
[ 68.442611] >> wlan1 index 16 name[host0].
cmd=[killall -9 ez-ipupdate ]
killall: ez-ipupdate: no process killed
cmd=[killall -9 tzoupdate-1.11 ]
killall: tzoupdate-1.11: no process killed
cmd=[killall process_monitor ]
killall: process_monitor: no process killed
cmd=[process_monitor ]
cmd=[killall zebra ]
num_servers=1
killall: zebra: no process killed
cmd=[killall ripd ]
gethostbyname 1.pool.ntp.org successed!!
func[do_ntp],ntp server is:[0.pool.ntp.org 1.pool.ntp.org 2.pool.ntp.org]
cmd=[ntpclient -h 4 0.pool.ntp.org 1.pool.ntp.org 2.pool.ntp.org -l -s -i 5 -c 1 ]
killall: ripd: no process killed
cmd=[killall -9 cron ]
File /tmp/ntp_firstboot not exist!, First boot!!
Hit enter to continue...cmd=[cron ]
cmd=[killall -9 qos_bw_detect ]
killall: qos_bw_detect: no process killed
cmd=[qos ]
cmd=[killall -9 vsftpd ]
cmd=[qos_bw_detect ]
return code=0, from ntpclient
-08,-08,-08 1 1
Time update successfully, adjust time. (adjust:-8.000000)
Year:2020,Month:7,Day:10,Hour:11,Min:52,Sec:40
TimeZone:4,i=4,starthour=2,startm=3,endhour=1,endmonth=11,diffm=0,j=13
Adjust daylight
dstBias:3600
,Year:2020,Month:7,Day:10,Hour:12,Min:52,Sec:40
killall: vsftpd: no process killed
cmd=[filtersync ]
_do_qos:start nss when disable QoS........
cmd=[radvd -C /tmp/radvd.conf ]
qos_bw_detect wait_time = 172800 seconds
We need to re-update after 86400 seconds
Hit enter to continue...
BusyBox v1.19.4 (2018-09-28 19:11:11 EDT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
~ # df
Filesystem 1K-blocks Used Available Use% Mounted on
rootfs 26604 52 25156 0% /
mtd:ubi_rootfs 29952 29952 0 100% /rom
tmpfs 243868 352 243516 0% /tmp
tmpfs 512 0 512 0% /dev
ubi0:ubi_rootfs_data 26604 52 25156 0% /overlay
overlayfs:/overlay 26604 52 25156 0% /
~ # mount
rootfs on / type rootfs (rw)
mtd:ubi_rootfs on /rom type squashfs (ro,relatime)
proc on /proc type proc (rw,noatime)
sysfs on /sys type sysfs (rw,noatime)
tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime)
tmpfs on /dev type tmpfs (rw,noatime,size=512k,mode=755)
devpts on /dev/pts type devpts (rw,noatime,mode=600)
ubi0:ubi_rootfs_data on /overlay type ubifs (rw,noatime)
overlayfs:/overlay on / type overlayfs (rw,noatime,lowerdir=/,upperdir=/overlay)
ramfs on /foreign_shares type ramfs (rw,relatime)
debugfs on /sys/kernel/debug type debugfs (rw,relatime)
none on /proc/bus/usb type usbfs (rw,relatime)
~ # cat /proc/mtd
dev: size erasesize name
mtd0: 04000000 00020000 “rootfs”
mtd1: 00010000 00010000 “sbl1”
mtd2: 00020000 00010000 “mibib”
mtd3: 00020000 00010000 “sbl2”
mtd4: 00030000 00010000 “sbl3”
mtd5: 00010000 00010000 “ddrconfig”
mtd6: 00010000 00010000 “ssd”
mtd7: 00030000 00010000 “tz”
mtd8: 00020000 00010000 “rpm”
mtd9: 00040000 00010000 “oldappsbl”
mtd10: 00040000 00010000 “APPSBLENV”
mtd11: 00020000 00010000 “ART”
mtd12: 00050000 00010000 “uboot”
mtd13: 00020000 00010000 “oldnss1”
mtd14: 00020000 00010000 “nvram”
mtd15: 001e0000 00010000 “oldkernel”
mtd16: 001d1000 0001f000 “kernel”
mtd17: 01d2f000 0001f000 “ubi_rootfs”
mtd18: 01de9000 0001f000 “ubi_rootfs_data”
~ # ls -ls /dev/ubi
ubi0 ubi0_0 ubi0_1 ubi0_2 ubi_ctrl
~ # ls -ls /dev/ubi*
0 crw-r--r-- 1 root root 248, 0 Jan 1 1970 /dev/ubi0
0 crw-r--r-- 1 root root 248, 1 Jan 1 1970 /dev/ubi0_0
0 crw-r--r-- 1 root root 248, 2 Jan 1 1970 /dev/ubi0_1
0 crw-r--r-- 1 root root 248, 3 Jan 1 1970 /dev/ubi0_2
0 crw-r--r-- 1 root root 10, 58 Jan 1 1970 /dev/ubi_ctrl
</WRAP>
==== OpenWrt bootlog ====
COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING [ 0.000000] Booting Linux on physical CPU 0x0 [ 0.000000] Linux version 5.4.50 (openwrt@tchome) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r13773-a6160de3f7)) #0 SMP Fri Jul 10 23:09:18 2020 [ 0.000000] CPU: ARMv7 Processor [512f04d0] revision 0 (ARMv7), cr=10c5787d [ 0.000000] CPU: div instructions available: patching division code [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, PIPT instruction cache [ 0.000000] OF: fdt: Machine model: Linksys EA8300 V1 WiFi Router [ 0.000000] Memory policy: Data cache writealloc [ 0.000000] On node 0 totalpages: 122880 [ 0.000000] Normal zone: 960 pages used for memmap [ 0.000000] Normal zone: 0 pages reserved [ 0.000000] Normal zone: 122880 pages, LIFO batch:31 [ 0.000000] percpu: Embedded 15 pages/cpu s29900 r8192 d23348 u61440 [ 0.000000] pcpu-alloc: s29900 r8192 d23348 u61440 alloc=15*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 121920 [ 0.000000] Kernel command line: [ 0.000000] Bootloader command line (ignored): console=ttyHSL1,115200n8 ubi.mtd=rootfs root=mtd:ubi_rootfs [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 478444K/491520K available (5712K kernel code, 165K rwdata, 884K rodata, 1024K init, 222K bss, 13076K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16 [ 0.000000] clocksource: dg_timer: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 305801671480 ns [ 0.000008] sched_clock: 32 bits at 6MHz, resolution 160ns, wraps every 343597383600ns [ 0.000021] Switching to timer-based delay loop, resolution 160ns [ 0.000212] Calibrating delay loop (skipped), value calculated using timer frequency.. 12.50 BogoMIPS (lpj=62500) [ 0.000232] pid_max: default: 32768 minimum: 301 [ 0.000379] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.000398] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.001099] CPU: Testing write buffer coherency: ok [ 0.002096] Setting up static identity map for 0x42300000 - 0x42300060 [ 0.002254] rcu: Hierarchical SRCU implementation. [ 0.002682] smp: Bringing up secondary CPUs ... [ 0.004484] smp: Brought up 1 node, 2 CPUs [ 0.004501] SMP: Total of 2 processors activated (25.00 BogoMIPS). [ 0.004511] CPU: All CPU(s) started in SVC mode. [ 0.014143] random: get_random_u32 called from 0xc0541e44 with crng_init=0 [ 0.014199] VFP support v0.3: implementor 51 architecture 64 part 4d variant 2 rev 0 [ 0.014364] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.014392] futex hash table entries: 512 (order: 3, 32768 bytes, linear) [ 0.014501] pinctrl core: initialized pinctrl subsystem [ 0.015616] NET: Registered protocol family 16 [ 0.015895] DMA: preallocated 256 KiB pool for atomic coherent allocations [ 0.017253] cpuidle: using governor ladder [ 0.017315] cpuidle: using governor menu [ 0.047968] usbcore: registered new interface driver usbfs [ 0.048060] usbcore: registered new interface driver hub [ 0.048148] usbcore: registered new device driver usb [ 0.048204] pps_core: LinuxPPS API ver. 1 registered [ 0.048217] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it [ 0.048250] PTP clock support registered [ 0.049978] clocksource: Switched to clocksource dg_timer [ 0.050788] thermal_sys: Registered thermal governor 'step_wise' [ 0.053364] NET: Registered protocol family 2 [ 0.053906] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 6144 bytes, linear) [ 0.053938] TCP established hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.053982] TCP bind hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.054037] TCP: Hash tables configured (established 4096 bind 4096) [ 0.054137] UDP hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.054165] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes, linear) [ 0.054369] NET: Registered protocol family 1 [ 0.054415] PCI: CLS 0 bytes, default 64 [ 0.055655] workingset: timestamp_bits=30 max_order=17 bucket_order=0 [ 0.061524] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.061539] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.100925] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda not found, using dummy regulator [ 0.101051] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_phy not found, using dummy regulator [ 0.101175] qcom-pcie 1b500000.pci: 1b500000.pci supply vdda_refclk not found, using dummy regulator [ 0.101442] qcom-pcie 1b500000.pci: host bridge /soc/pci@1b500000 ranges: [ 0.101466] qcom-pcie 1b500000.pci: Parsing ranges property... [ 0.101516] qcom-pcie 1b500000.pci: IO 0x0fe00000..0x0fefffff → 0x0fe00000 [ 0.101557] qcom-pcie 1b500000.pci: MEM 0x08000000..0x0fdfffff → 0x08000000 [ 0.325878] qcom-pcie 1b500000.pci: Link up [ 0.326057] qcom-pcie 1b500000.pci: PCI host bridge to bus 0000:00 [ 0.326082] pci_bus 0000:00: root bus resource [bus 00-ff] [ 0.326103] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0xfe00000-0xfefffff]) [ 0.326120] pci_bus 0000:00: root bus resource [mem 0x08000000-0x0fdfffff] [ 0.326136] pci_bus 0000:00: scanning bus [ 0.326184] pci 0000:00:00.0: [17cb:0101] type 01 class 0xff0000 [ 0.326357] pci 0000:00:00.0: supports D1 [ 0.326372] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.326392] pci 0000:00:00.0: PME# disabled [ 0.329944] pci_bus 0000:00: fixups for bus [ 0.329967] PCI: bus0: Fast back to back transfers disabled [ 0.329987] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 0 [ 0.330127] pci_bus 0000:01: scanning bus [ 0.330423] pci 0000:01:00.0: [1bb5:0008] type 00 class 0x028000 [ 0.330710] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x0000ffff pref] [ 0.330889] pci 0000:01:00.0: reg 0x18: [mem 0x00000000-0x0000ffff pref] [ 0.330987] pci 0000:01:00.0: reg 0x1c: [mem 0x00000000-0x0000ffff pref] [ 0.331953] pci 0000:01:00.0: supports D1 [ 0.331967] pci 0000:01:00.0: PME# supported from D0 D1 D3hot [ 0.332013] pci 0000:01:00.0: PME# disabled [ 0.332271] pci 0000:01:00.0: 2.000 Gb/s available PCIe bandwidth, limited by 2.5 GT/s x1 link at 0000:00:00.0 (capable of 4.000 Gb/s with 5 GT/s x1 link) [ 0.335773] pci_bus 0000:01: fixups for bus [ 0.335849] PCI: bus1: Fast back to back transfers disabled [ 0.335865] pci_bus 0000:01: bus scan returning with max=01 [ 0.335884] pci 0000:00:00.0: scanning [bus 01-ff] behind bridge, pass 1 [ 0.335903] pci_bus 0000:00: bus scan returning with max=ff [ 0.335938] pci 0000:00:00.0: BAR 8: assigned [mem 0x08000000-0x080fffff] [ 0.335972] pci 0000:01:00.0: BAR 0: assigned [mem 0x08000000-0x0800ffff pref] [ 0.336028] pci 0000:01:00.0: BAR 2: assigned [mem 0x08010000-0x0801ffff pref] [ 0.336082] pci 0000:01:00.0: BAR 3: assigned [mem 0x08020000-0x0802ffff pref] [ 0.336137] pci 0000:00:00.0: PCI bridge to [bus 01-ff] [ 0.336163] pci 0000:00:00.0: bridge window [mem 0x08000000-0x080fffff] [ 0.336369] pcieport 0000:00:00.0: assign IRQ: got 35 [ 0.336893] pcieport 0000:00:00.0: AER: enabled with IRQ 36 [ 0.337490] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda not found, using dummy regulator [ 0.337611] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_phy not found, using dummy regulator [ 0.337726] qcom-pcie 1b700000.pci: 1b700000.pci supply vdda_refclk not found, using dummy regulator [ 0.337995] qcom-pcie 1b700000.pci: host bridge /soc/pci@1b700000 ranges: [ 0.338023] qcom-pcie 1b700000.pci: Parsing ranges property... [ 0.338065] qcom-pcie 1b700000.pci: IO 0x31e00000..0x31efffff → 0x31e00000 [ 0.338108] qcom-pcie 1b700000.pci: MEM 0x2e000000..0x31dfffff → 0x2e000000 [ 0.567397] qcom-pcie 1b700000.pci: Link up [ 0.567561] qcom-pcie 1b700000.pci: PCI host bridge to bus 0001:00 [ 0.567581] pci_bus 0001:00: root bus resource [bus 00-ff] [ 0.567596] pci_bus 0001:00: root bus resource [mem 0x2e000000-0x31dfffff] [ 0.567609] pci_bus 0001:00: scanning bus [ 0.567651] pci 0001:00:00.0: [17cb:0101] type 01 class 0xff0000 [ 0.567801] pci 0001:00:00.0: supports D1 [ 0.567815] pci 0001:00:00.0: PME# supported from D0 D1 D3hot [ 0.567833] pci 0001:00:00.0: PME# disabled [ 0.571432] pci_bus 0001:00: fixups for bus [ 0.571453] PCI: bus0: Fast back to back transfers disabled [ 0.571471] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 0 [ 0.571591] pci_bus 0001:01: scanning bus [ 0.571780] pci 0001:01:00.0: [168c:003c] type 00 class 0x028000 [ 0.572139] pci 0001:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit] [ 0.572556] pci 0001:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.573388] pci 0001:01:00.0: supports D1 D2 [ 0.573403] pci 0001:01:00.0: PME# supported from D0 D1 D2 D3hot D3cold [ 0.573449] pci 0001:01:00.0: PME# disabled [ 0.577166] pci_bus 0001:01: fixups for bus [ 0.577243] PCI: bus1: Fast back to back transfers disabled [ 0.577259] pci_bus 0001:01: bus scan returning with max=01 [ 0.577276] pci 0001:00:00.0: scanning [bus 01-ff] behind bridge, pass 1 [ 0.577292] pci_bus 0001:00: bus scan returning with max=ff [ 0.577318] pci 0001:00:00.0: BAR 8: assigned [mem 0x2e000000-0x2e2fffff] [ 0.577342] pci 0001:01:00.0: BAR 0: assigned [mem 0x2e000000-0x2e1fffff 64bit] [ 0.577480] pci 0001:01:00.0: BAR 6: assigned [mem 0x2e200000-0x2e20ffff pref] [ 0.577498] pci 0001:00:00.0: PCI bridge to [bus 01-ff] [ 0.577518] pci 0001:00:00.0: bridge window [mem 0x2e000000-0x2e2fffff] [ 0.577709] pcieport 0001:00:00.0: assign IRQ: got 37 [ 0.578367] pcieport 0001:00:00.0: AER: enabled with IRQ 38 [ 0.578964] qcom-pcie 1b900000.pci: 1b900000.pci supply vdda not found, using dummy regulator [ 0.579086] qcom-pcie 1b900000.pci: 1b900000.pci supply vdda_phy not found, using dummy regulator [ 0.579188] qcom-pcie 1b900000.pci: 1b900000.pci supply vdda_refclk not found, using dummy regulator [ 0.579446] qcom-pcie 1b900000.pci: host bridge /soc/pci@1b900000 ranges: [ 0.579470] qcom-pcie 1b900000.pci: Parsing ranges property... [ 0.579512] qcom-pcie 1b900000.pci: IO 0x35e00000..0x35efffff → 0x35e00000 [ 0.579548] qcom-pcie 1b900000.pci: MEM 0x32000000..0x35dfffff → 0x32000000 [ 1.729990] qcom-pcie 1b900000.pci: Phy link never came up [ 1.731998] qcom-pcie 1b900000.pci: cannot initialize host [ 1.732373] qcom-pcie: probe of 1b900000.pci failed with error -110 [ 1.734653] L2 @ QSB rate. Forcing new rate. [ 1.734881] L2 @ 384000 KHz [ 1.735064] CPU0 @ 800000 KHz [ 1.735078] CPU1 @ QSB rate. Forcing new rate. [ 1.735207] CPU1 @ 384000 KHz [ 1.738963] gsbi 16300000.gsbi: GSBI port protocol: 6 crci: 0 [ 1.739660] gsbi 1a200000.gsbi: GSBI port protocol: 3 crci: 0 [ 1.741208] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 1.742019] msm_serial 16340000.serial: msm_serial: detected port #0 [ 1.742072] msm_serial 16340000.serial: uartclk = 7372800 [ 1.742143] 16340000.serial: ttyMSM0 at MMIO 0x16340000 (irq = 39, base_baud = 460800) is a MSM [ 1.742180] msm_serial: console setup on port #0 [ 2.630565] printk: console [ttyMSM0] enabled [ 2.635571] msm_serial: driver initialized [ 2.644505] loop: module loaded [ 2.645841] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xa1 [ 2.646624] nand: Micron MT29F1G08ABBDAH4 [ 2.653323] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 2.657173] 1 fixed-partitions partitions found on MTD device qcom_nand.0 [ 2.664686] Creating 1 MTD partitions on “qcom_nand.0”: [ 2.671535] 0x000000000000-0x000008000000 : “ubi” [ 2.684598] random: fast init done [ 3.184954] random: crng init done [ 4.135759] spi_qup 1a280000.spi: IN:block:16, fifo:64, OUT:block:16, fifo:64 [ 4.141447] spi-nor spi0.0: mx25u3235f (4096 Kbytes) [ 4.141976] 15 qcom-smem partitions found on MTD device spi0.0 [ 4.146922] Creating 15 MTD partitions on “spi0.0”: [ 4.152676] 0x000000000000-0x000000010000 : “0:SBL1” [ 4.158782] 0x000000010000-0x000000030000 : “0:MIBIB” [ 4.163927] 0x000000030000-0x000000050000 : “0:SBL2” [ 4.168762] 0x000000050000-0x000000080000 : “0:SBL3” [ 4.173898] 0x000000080000-0x000000090000 : “0:DDRCONFIG” [ 4.178766] 0x000000090000-0x0000000a0000 : “0:SSD” [ 4.184135] 0x0000000a0000-0x0000000d0000 : “0:TZ” [ 4.188722] 0x0000000d0000-0x0000000f0000 : “0:RPM” [ 4.193716] 0x0000000f0000-0x000000130000 : “0:OLDAPPSBL” [ 4.198378] 0x000000130000-0x000000170000 : “0:APPSBLENV” [ 4.204039] 0x000000170000-0x000000190000 : “0:ART” [ 4.209328] 0x000000190000-0x0000001e0000 : “0:APPSBL” [ 4.214139] 0x0000001e0000-0x000000200000 : “0:NSS1” [ 4.219204] 0x000000200000-0x000000220000 : “0:NVRAM” [ 4.224454] 0x000000220000-0x000000400000 : “0:HLOS” [ 4.231406] libphy: ipq8064_mdio_bus: probed [ 4.283114] switch0: Atheros AR8337 rev. 2 switch registered on 37000000.mdio-mii [ 5.384612] libphy: Fixed MDIO Bus: probed [ 5.385625] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_wake_irq not found [ 5.387620] ipq806x-gmac-dwmac 37200000.ethernet: IRQ eth_lpi not found [ 5.395255] ipq806x-gmac-dwmac 37200000.ethernet: PTP uses main clock [ 5.402184] ipq806x-gmac-dwmac 37200000.ethernet: User ID: 0x10, Synopsys ID: 0x37 [ 5.407763] ipq806x-gmac-dwmac 37200000.ethernet: DWMAC1000 [ 5.415335] ipq806x-gmac-dwmac 37200000.ethernet: DMA HW capability register supported [ 5.421129] ipq806x-gmac-dwmac 37200000.ethernet: RX Checksum Offload Engine supported [ 5.428763] ipq806x-gmac-dwmac 37200000.ethernet: COE Type 2 [ 5.436763] ipq806x-gmac-dwmac 37200000.ethernet: TX Checksum insertion supported [ 5.442559] ipq806x-gmac-dwmac 37200000.ethernet: Wake-Up On Lan supported [ 5.449858] ipq806x-gmac-dwmac 37200000.ethernet: Enhanced/Alternate descriptors [ 5.456710] ipq806x-gmac-dwmac 37200000.ethernet: Enabled extended descriptors [ 5.464271] ipq806x-gmac-dwmac 37200000.ethernet: Ring mode enabled [ 5.471299] ipq806x-gmac-dwmac 37200000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 5.477390] ipq806x-gmac-dwmac 37200000.ethernet: device MAC address fa:49:36:39:6b:57 [ 5.487500] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_wake_irq not found [ 5.493894] ipq806x-gmac-dwmac 37400000.ethernet: IRQ eth_lpi not found [ 5.501375] ipq806x-gmac-dwmac 37400000.ethernet: PTP uses main clock [ 5.507868] ipq806x-gmac-dwmac 37400000.ethernet: User ID: 0x10, Synopsys ID: 0x37 [ 5.514051] ipq806x-gmac-dwmac 37400000.ethernet: DWMAC1000 [ 5.521473] ipq806x-gmac-dwmac 37400000.ethernet: DMA HW capability register supported [ 5.527200] ipq806x-gmac-dwmac 37400000.ethernet: RX Checksum Offload Engine supported [ 5.535043] ipq806x-gmac-dwmac 37400000.ethernet: COE Type 2 [ 5.542901] ipq806x-gmac-dwmac 37400000.ethernet: TX Checksum insertion supported [ 5.548640] ipq806x-gmac-dwmac 37400000.ethernet: Wake-Up On Lan supported [ 5.556115] ipq806x-gmac-dwmac 37400000.ethernet: Enhanced/Alternate descriptors [ 5.562894] ipq806x-gmac-dwmac 37400000.ethernet: Enabled extended descriptors [ 5.570423] ipq806x-gmac-dwmac 37400000.ethernet: Ring mode enabled [ 5.577370] ipq806x-gmac-dwmac 37400000.ethernet: Enable RX Mitigation via HW Watchdog Timer [ 5.583649] ipq806x-gmac-dwmac 37400000.ethernet: device MAC address b6:c3:1d:f8:f4:4b [ 5.593817] i2c /dev entries driver [ 5.603512] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations [ 5.603843] cpuidle: enable-method property 'qcom,kpss-acc-v1' found operations [ 5.611712] sdhci: Secure Digital Host Controller Interface driver [ 5.617904] sdhci: Copyright© Pierre Ossman [ 5.624251] sdhci-pltfm: SDHCI platform and OF driver helper [ 5.632107] NET: Registered protocol family 10 [ 5.637370] Segment Routing with IPv6 [ 5.638715] NET: Registered protocol family 17 [ 5.643581] 8021q: 802.1Q VLAN Support v1.8 [ 5.646686] Registering SWP/SWPB emulation handler [ 5.683177] qcom_rpm 108000.rpm: RPM firmware 3.0.16777338 [ 5.708566] s1a: supplied by regulator-dummy [ 5.708705] s1a: Bringing 0uV into 1050000-1050000uV [ 5.712506] s1b: supplied by regulator-dummy [ 5.716958] s1b: Bringing 0uV into 1050000-1050000uV [ 5.721635] s2a: supplied by regulator-dummy [ 5.726150] s2a: Bringing 0uV into 800000-800000uV [ 5.730838] s2b: supplied by regulator-dummy [ 5.735025] s2b: Bringing 0uV into 800000-800000uV [ 5.741788] Speed bin: 0 [ 5.743933] PVS bin: 2 [ 5.748893] core: _opp_supported_by_regulators: OPP minuV: 995000 maxuV: 995000, not supported by regulator [ 5.748951] cpu cpu0: _opp_add: OPP not supported by regulators (800000000) [ 5.759853] cpufreq: cpufreq_online: CPU0: Running at unlisted freq: 800000 KHz [ 5.765725] cpufreq: cpufreq_online: CPU0: Unlisted initial frequency changed to: 1000000 KHz [ 5.774260] core: _opp_supported_by_regulators: OPP minuV: 995000 maxuV: 995000, not supported by regulator [ 5.781459] cpu cpu1: _opp_add: OPP not supported by regulators (800000000) [ 5.798718] UBI: auto-attach mtd0 [ 5.798742] ubi0: default fastmap pool size: 50 [ 5.801415] ubi0: default fastmap WL pool size: 25 [ 5.805652] ubi0: attaching mtd0 [ 7.388215] ubi0: scanning is finished [ 7.410482] ubi0: attached mtd0 (name “ubi”, size 128 MiB) [ 7.410502] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 7.414850] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 7.421788] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 7.428566] ubi0: good PEBs: 1024, bad PEBs: 0, corrupted PEBs: 0 [ 7.435411] ubi0: user volume: 3, internal volumes: 1, max. volumes count: 128 [ 7.441652] ubi0: max/mean erase counter: 1/0, WL threshold: 4096, image sequence number: 1594422558 [ 7.448710] ubi0: available PEBs: 495, total reserved PEBs: 529, PEBs reserved for bad PEB handling: 20 [ 7.458886] mtd: device 17 (rootfs) set to be root filesystem [ 7.459038] ubi0: background thread “ubi_bgt0d” started, PID 64 [ 7.468717] block ubiblock0_1: created from ubi0:1(rootfs) [ 7.478785] hctosys: unable to open rtc device (rtc0) [ 7.498199] VFS: Mounted root (squashfs filesystem) readonly on device 31:17. [ 7.500513] Freeing unused kernel memory: 1024K [ 7.532254] Run /sbin/init as init process [ 8.510987] init: Console is alive [ 8.511114] init: - watchdog - [ 11.976623] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 12.009925] raid6: using algorithm neonx8 gen() 0 MB/s [ 12.009956] raid6: .... xor() 0 MB/s, rmw enabled [ 12.014061] raid6: using neon recovery algorithm [ 12.019966] xor: measuring software checksum speed [ 12.120350] arm4regs : 1061.600 MB/sec [ 12.220349] 8regs : 672.800 MB/sec [ 12.320349] 32regs : 668.400 MB/sec [ 12.420343] neon : 2446.000 MB/sec [ 12.420366] xor: using function: neon (2446.000 MB/sec) [ 12.641377] Btrfs loaded, crc32c=crc32c-generic [ 12.655687] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 12.658601] SCSI subsystem initialized [ 12.666407] libata version 3.00 loaded. [ 12.669630] ehci-fsl: Freescale EHCI Host controller driver [ 12.670139] ehci-platform: EHCI generic platform driver [ 12.677474] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 12.679577] ohci-platform: OHCI generic platform driver [ 12.688165] dwc3-qcom 110f8800.usb3: IRQ hs_phy_irq not found [ 12.690669] dwc3-qcom 110f8800.usb3: IRQ dp_hs_phy_irq not found [ 12.696485] dwc3-qcom 110f8800.usb3: IRQ dm_hs_phy_irq not found [ 12.702637] dwc3-qcom 110f8800.usb3: IRQ ss_phy_irq not found [ 12.710160] dwc3-qcom 100f8800.usb3: IRQ hs_phy_irq not found [ 12.714195] dwc3-qcom 100f8800.usb3: IRQ dp_hs_phy_irq not found [ 12.719922] dwc3-qcom 100f8800.usb3: IRQ dm_hs_phy_irq not found [ 12.726071] dwc3-qcom 100f8800.usb3: IRQ ss_phy_irq not found [ 12.742963] dwc3 11000000.dwc3: Failed to get clk 'ref': -2 [ 12.791328] dwc3 10000000.dwc3: Failed to get clk 'ref': -2 [ 12.854320] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 12.854381] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1 [ 12.858917] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010 [ 12.866407] xhci-hcd xhci-hcd.0.auto: irq 43, io mem 0x11000000 [ 12.876643] hub 1-0:1.0: USB hub found [ 12.881623] hub 1-0:1.0: 1 port detected [ 12.885565] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller [ 12.889441] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2 [ 12.894798] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed [ 12.903115] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM. [ 12.909239] hub 2-0:1.0: USB hub found [ 12.917212] hub 2-0:1.0: 1 port detected [ 12.922097] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 12.924771] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3 [ 12.930191] xhci-hcd xhci-hcd.1.auto: hcc params 0x0228f065 hci version 0x100 quirks 0x0000000002010010 [ 12.937713] xhci-hcd xhci-hcd.1.auto: irq 44, io mem 0x10000000 [ 12.948844] hub 3-0:1.0: USB hub found [ 12.952982] hub 3-0:1.0: 1 port detected [ 12.956885] xhci-hcd xhci-hcd.1.auto: xHCI Host Controller [ 12.960865] xhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4 [ 12.966082] xhci-hcd xhci-hcd.1.auto: Host supports USB 3.0 SuperSpeed [ 12.973777] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 12.980608] hub 4-0:1.0: USB hub found [ 12.988488] hub 4-0:1.0: 1 port detected [ 12.994406] usbcore: registered new interface driver usb-storage [ 12.996203] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 13.006292] init: - preinit - [ 15.917227] dwmac1000: Master AXI performs any burst length [ 15.917274] ipq806x-gmac-dwmac 37400000.ethernet eth1: No Safety Features support found [ 15.921738] ipq806x-gmac-dwmac 37400000.ethernet eth1: IEEE 1588-2008 Advanced Timestamp supported [ 15.929791] ipq806x-gmac-dwmac 37400000.ethernet eth1: registered PTP clock [ 15.938733] ipq806x-gmac-dwmac 37400000.ethernet eth1: configuring for fixed/sgmii link mode [ 15.946812] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Up - 1Gbps/Full - flow control off [ 15.946868] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready [ 19.085301] Starting lvm2 during preinit [ 21.089217] device-mapper: ioctl: 4.41.0-ioctl (2019-09-16) initialised: dm-devel@redhat.com [ 21.429213] mount_root: loading kmods from internal overlay [ 21.460100] kmodloader: loading kernel modules from etc/modules-boot.d/* [ 21.463681] kmodloader: done loading kernel modules from etc/modules-boot.d/* [ 23.188074] UBIFS (ubi0:2): default file-system created [ 23.189798] UBIFS (ubi0:2): Mounting in unauthenticated mode [ 23.193356] UBIFS (ubi0:2): background thread “ubifs_bgt0_2” started, PID 157 [ 23.453765] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name “rootfs_data” [ 23.453808] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 23.460685] UBIFS (ubi0:2): FS size: 44314624 bytes (42 MiB, 349 LEBs), journal size 2158592 bytes (2 MiB, 17 LEBs) [ 23.470572] UBIFS (ubi0:2): reserved for root: 2093089 bytes (2044 KiB) [ 23.480792] UBIFS (ubi0:2): media format: w4/r0 (latest is w5/r0), UUID 66F4BC49-4029-4011-AA8E-82C7DCAB48CE, small LPT model [ 23.489420] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 23.499073] block: unable to load configuration (fstab: Entry not found) [ 23.505706] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab [ 23.512807] block: unable to load configuration (fstab: Entry not found) [ 23.518882] block: attempting to load /etc/config/fstab [ 23.526369] block: unable to load configuration (fstab: Entry not found) [ 23.530658] block: no usable configuration [ 23.544934] UBIFS (ubi0:2): un-mount UBI device 0 [ 23.545917] UBIFS (ubi0:2): background thread “ubifs_bgt0_2” stops [ 23.553591] UBIFS (ubi0:2): Mounting in unauthenticated mode [ 23.555724] UBIFS (ubi0:2): background thread “ubifs_bgt0_2” started, PID 158 [ 23.739886] UBIFS (ubi0:2): UBIFS: mounted UBI device 0, volume 2, name “rootfs_data” [ 23.739925] UBIFS (ubi0:2): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 23.746811] UBIFS (ubi0:2): FS size: 44314624 bytes (42 MiB, 349 LEBs), journal size 2158592 bytes (2 MiB, 17 LEBs) [ 23.756679] UBIFS (ubi0:2): reserved for root: 2093089 bytes (2044 KiB) [ 23.766916] UBIFS (ubi0:2): media format: w4/r0 (latest is w5/r0), UUID 66F4BC49-4029-4011-AA8E-82C7DCAB48CE, small LPT model [ 25.615772] ubi0 error: 0xc06599b0: cannot open device 0, volume 2, error -16 [ 25.615827] ubi0 error: 0xc06599b0: cannot open device 0, volume 2, error -16 [ 26.985704] block: attempting to load /tmp/ubifs_cfg/upper/etc/config/fstab [ 26.985790] block: unable to load configuration (fstab: Entry not found) [ 26.991577] block: attempting to load /tmp/ubifs_cfg/etc/config/fstab [ 26.998474] block: unable to load configuration (fstab: Entry not found) [ 27.004863] block: attempting to load /etc/config/fstab [ 27.011632] block: unable to load configuration (fstab: Entry not found) [ 27.016494] block: no usable configuration [ 27.025178] mount_root: overlay filesystem has not been fully initialized yet [ 27.027536] mount_root: switching to ubifs overlay [ 27.066857] overlayfs: upper fs does not support xattr, falling back to index=off and metacopy=off. [ 27.072508] urandom-seed: Seed file not found (/etc/urandom.seed) [ 27.112552] ipq806x-gmac-dwmac 37400000.ethernet eth1: Link is Down [ 27.161181] procd: - early - [ 27.161333] procd: - watchdog - [ 27.732439] procd: - watchdog - [ 27.732704] procd: - ubus - [ 27.795801] procd: - init - [ 28.127652] urngd: v1.0.2 started. [ 28.134320] kmodloader: loading kernel modules from /etc/modules.d/* [ 28.148232] NET: Registered protocol family 38 [ 28.153981] FS-Cache: Loaded [ 28.157294] Key type dns_resolver registered [ 28.164736] Key type cifs.idmap registered [ 28.175300] RPC: Registered named UNIX socket transport module. [ 28.175322] RPC: Registered udp transport module. [ 28.180014] RPC: Registered tcp transport module. [ 28.184956] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 28.194653] tun: Universal TUN/TAP device driver, 1.6 [ 28.210514] Installing knfsd (copyright (C) 1996 okir@monad.swb.de). [ 28.215579] NFS: Registering the id_resolver key type [ 28.215941] Key type id_resolver registered [ 28.220954] Key type id_legacy registered [ 28.236993] Mirror/redirect action on [ 28.240169] u32 classifier [ 28.240184] input device check on [ 28.242323] Actions configured [ 28.261510] fuse: init (API version 7.31) [ 28.264404] Loading modules backported from Linux version v5.7-rc3-0-g6a8b55ed4056 [ 28.264495] Backport generated by backports.git v5.7-rc3-1-0-gc0c7d2bb [ 28.349020] xt_time: kernel timezone is -0000 [ 28.389221] PPP generic driver version 2.4.2 [ 28.390520] NET: Registered protocol family 24 [ 28.420944] ath10k_pci 0001:01:00.0: assign IRQ: got 37 [ 28.420967] ath10k 5.4 driver, optimized for CT firmware, probing pci device: 0x3c. [ 28.421023] ath10k_mac_create, priv_size: 868 hw: 37b53e8d hw→priv: ab0078a2 [ 28.437075] ath10k_pci 0001:01:00.0: enabling device (0140 → 0142) [ 28.437182] ath10k_pci 0001:01:00.0: enabling bus mastering [ 28.437715] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 29.297554] ath10k_pci 0001:01:00.0: qca988x hw2.0 target 0x4100016c chip_id 0x043202ff sub 0000:0000 [ 29.297589] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 0 testmode 0 [ 29.306684] ath10k_pci 0001:01:00.0: firmware ver 10.1-ct-8x-__fW-022-538f0906 api 2 features wmi-10.x,has-wmi-mgmt-tx,mfp,txstatus-noack,wmi-10.x-CT,ratemask-CT,txrate-CT,get-temp-CT,tx4 [ 29.419120] ath10k_pci 0001:01:00.0: board_file api 1 bmi_id N/A crc32 bebc7c08 [ 30.341299] ath10k_pci 0001:01:00.0: unsupported HTC service id: 1536 [ 30.343860] ath10k_pci 0001:01:00.0: 10.1 wmi init: vdevs: 16 peers: 127 tid: 256 [ 30.356810] ath10k_pci 0001:01:00.0: wmi print 'P 128 V 8 T 410' [ 30.356838] ath10k_pci 0001:01:00.0: wmi print 'msdu-desc: 1424 sw-crypt: 0 ct-sta: 0' [ 30.361945] ath10k_pci 0001:01:00.0: wmi print 'alloc rem: 20984 iram: 25656' [ 30.415394] ath10k_pci 0001:01:00.0: htt-ver 2.1 wmi-op 2 htt-op 2 cal otp max-sta 128 raw 0 hwcrypto 1 [ 30.428566] ath10k_pci 0001:01:00.0: NOTE: Firmware DBGLOG output disabled in debug_mask: 0x10000000 [ 30.537788] ath: EEPROM regdomain sanitized [ 30.537798] ath: EEPROM regdomain: 0x64 [ 30.537805] ath: EEPROM indicates we should expect a direct regpair map [ 30.537820] ath: Country alpha2 being used: 00 [ 30.537826] ath: Regpair used: 0x64
===== Notes =====
Possible non invasive recovery method:
(return to original firmware)
1. Power off the device
2. Press & hold the “Reset” button
3. Power on the deiece & wait for 10 seconds with pressed “Reset” button.The Router will open Firmware Recovery “http” server on IP: 192.168.1.1
4. Set IP on your PC from 192.168.1.0/24 network ( Router is on IP 192.168.1.1 )
5. Open in browser URL: http://192.168.1.1/index.shtml
- Firmware Recovery → File Name → Recovery & Reboot
===== Tags =====
How to add tags
- Last modified: 2020/07/15 11:36
- by tcolov



