BT-PON BT-G711AX
The BT-PON BT-G711AX is a XPON (GPON/EPON) ONU and a home router (HGU) with phone ATA and 802.11ax wifi. This variant doesn't have a CATV and uses UPC connector.
OpenWrt support
Not supported. Work in progress. At the current moment, only initramfs OpenWrt can be booted to console with working serial port. The github pull request for initial support of RTL9607C SoC, which also include this device: https://github.com/openwrt/openwrt/pull/20064
Hardware highlights
| CPU | Ram | Flash | Network | WLAN | USB | Phone | Fiber | Serial | JTag |
|---|---|---|---|---|---|---|---|---|---|
| Reatek RTL9607C @ 1150 MHz | 256 MiB | 128 MiB | 4x 1Gb | bgn + ax | 1x 2.0 | Yes | Yes | Yes | No |
Hardware
Info
| Architecture | MIPS |
|---|---|
| Vendor | BT-PON |
| Bootloader | Bismarck Preloader 3.7 + U-Boot 2020.01 |
| System-On-Chip | Realtek RTL9607C (VB) - MIPS interAptiv |
| CPU/Speed | 2 Cores 1150MHz |
| Flash-Chip | Winbond W25N01GVZEIG |
| Flash size | 128 MiB |
| RAM | Embedded 256 MiB |
| Wireless | Realtek RTL8192XBR, Realtek RTL8832BR |
| Ethernet | 4x GbE LAN (10/100/1000Mbit/s + Link & Act LED) |
| Switch | Built into Realtek RTL9607C |
| Phone | 1x RJ11 SIP & VoIP via Si32192FM1 |
| Fiber | 1x XPON SC-UPC via Semtech GN25L95 driver |
| USB | 1x 2.0 |
| Serial | Yes |
| GPIO Buttons | 3 (WPS, WLAN, Reset) |
| GPIO LEDs | 12 (Red/green) |
| Power | External 12V DC, 1.5A with a 5.5mm barrel connector |
Photos
Opening the case
There are 4 Phillips screws hidden beneath the sticky rubber feet. Use several prying tools or picks to pry open the case as it's held in place by tight plastic tabs
Serial
→ port.serial general information about the serial port, serial port cable, etc.
How to connect to the Serial Port of this specific device:
It uses 115200 bps baud rate over UART. The board comes with no header but you can still connect to it if you have cables with male ends. Soldering the pins is another option.
| Serial connection parameters for BT-PON BT-G711AX | 115200, 8N1, 3.3V |
|---|
Bootlogs
OEM bootlog
Bismarck Preloader 3.7 II: LPLR:11261 PLR:5cb134c9 BD:23062109 TK:msdk-4.8.5-mips-EB-3.18-u0.9.33-m32ut-170828_lunapro-171213 II: TLB initial done: .ro section works! .text and .ro sections work! II: cg_cpu_pll_init done II: CPU0 1150MHz, CPU1 600MHz, DDR3 666MHz, LX 200MHz, SRAM 500MHz, SPIF 100MHz II: apro_otp_setup_fcn(fc) AK: ******* DRAM calibration version: v5.6 ******* AK: MEMPLL[31/63/95/127/159/191/223]=907f, c0000210, 64237c0, 320f0030, fff, a7f, 0 AK: TP=3, VD=1, CC=3, OT=2, EP=0, EB=0 ZQ: Clock: ODT/OCD=60/48, zq_zctrl_prog=0x c08033e, zq_zctrl_status=0x20a144 ZQ: Address: ODT/OCD=60/80, zq_zctrl_prog=0x1c080332, zq_zctrl_status=0x20a100 ZQ: DQ: ODT/OCD=60/60, zq_zctrl_prog=0x2c080338, zq_zctrl_status=0x20a122 ZQ: DQS: ODT/OCD=60/60, zq_zctrl_prog=0x3c080338, zq_zctrl_status=0x20a122 ZQ: INTERAL DDR3, ZQCL done, ZQCS Enable AK: MRS: mr[0]=0x101a50, mr[1]=0x110004, mr[2]=0x120010, mr[3]=0x130000 AK: Start DDR_Calibration AK: Bit/max_r_s/max_r_l/max_w_s/max_w_l Bit/max_r_s/max_r_l/max_w_s/max_w_l [ 0] 0 1f 0 1d [16] 0 1f 0 1f [ 1] 0 1f 0 1f [17] 0 1f 0 1f [ 2] 0 1f 0 1f [18] 0 1f 0 1f [ 3] 0 1f 0 1f [19] 0 1f 0 1f [ 4] 0 1f 0 1f [20] 0 1f 0 1f [ 5] 0 1f 0 1f [21] 0 1f 0 1f [ 6] 0 1f 0 1f [22] 0 1f 0 1f [ 7] 0 1f 0 1f [23] 0 1f 0 1f [ 8] 0 1f 0 1f [24] 0 1f 0 1f [ 9] 0 1f 0 1f [25] 0 1f 0 1f [10] 0 1f 0 1f [26] 0 1f 0 1f [11] 0 1f 0 1f [27] 0 1f 0 1f [12] 0 1f 0 1f [28] 0 1f 0 1f [13] 0 1f 0 1f [29] 0 1f 0 1f [14] 0 1f 0 1f [30] 0 1f 0 1f [15] 0 1f 0 1f [31] 0 1f 0 1f AK: Finish DDR_Calibration AK: DRAM size=0x10000000, tRFC[2]=0x165(nS), tREF=1729(nS) AK: DCR=0x21321003, DTR[0:2]=0x99655828, 0x909061f, 0x6f19000 II: Change Stack from 0x9f002edc to 0x806fffe0 II: U-boot Magic Number is 0x27051956 II: Inflating U-Boot (0x80700040 -> 0x83c00000)... OK II: Starting U-boot... U-Boot 2020.01 (Jun 21 2023 - 11:08:33 +0800) Board: RTL9607Cv2, MIPS interAptiv:1150MHz RLX5281:600MHz LX:200MHz DDR3:666MHz SCLK:100MHz ICACHE: 64KB (32-byte/4-way/512-set) DCACHE: 32KB (32-byte/4-way/256-set) DRAM: Physical 256 MiB, uboot useable size 256 MiB NAND: SPI NAND: 0xEFAA21, Mode(111/111) Create bbt: NAND: 128 MiB Loading Environment from NAND... OK In: serial Out: serial Err: serial II: Init Software Patch! II: sw_test II: Configurate otto_flash_layout Saving Environment to NAND... Erasing redundant NAND... Erasing at 0x100000 -- 100% complete. Writing to redundant NAND... OK OK NAND read: device 0 offset 0x0, size 0xe0000 917504 bytes read: OK CRC32 for 81c80000 ... 81d5ffff ==> 65d8241a Net: LUNA GMAC Warning: eth device name has a space! Hit any key to stop autoboot: 1 0 swcore_init multicast_start Using LUNA GMAC device mcast upgrade timeout. ubi0: attaching mtd5 ubi0: scanning is finished ubi0: attached mtd5 (name "ubi_device", size 124 MiB) ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 ubi0: good PEBs: 994, bad PEBs: 0, corrupted PEBs: 0 ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128 ubi0: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 163500012 ubi0: available PEBs: 303, total reserved PEBs: 691, PEBs reserved for bad PEB handling: 20 No size specified -> Using max size (10539008) Read 10539008 bytes from volume ubi_k0 to 83000000 ## Booting kernel from Legacy Image at 83000000 ... Image Name: Linux-4.4.140 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 3431577 Bytes = 3.3 MiB Load Address: 80010000 Entry Point: 807d4c00 Verifying Checksum ... OK Uncompressing Kernel Image DEBUG_MEM_AUTO: mem_size=0x10000000, bankcnt=0x00000008, banksize=0x02000000 (dcr=0x21321003) DEBUG_MEM_AUTO: BSP_DSP_MEM_BASE=0xf900000, SIZE=0x700000 DEBUG_MEM_AUTO: BSP_IPC_MEM_BASE=0xf800000, SIZE=0x100000 DEBUG_MEM_AUTO: LUNA_PBO_UL_DRAM_OFFSET = 0x0f700000, SIZE_BARRIER = 0x00100000 DEBUG_MEM_AUTO: LUNA_PBO_DL_DRAM_OFFSET = 0x0dc00000, SIZE_BARRIER = 0x00400000 DEBUG_MEM_AUTO: PAGE_SIZE = 0x00001000 DEBUG_MEM_AUTO: [bsp_prom_memmap]add_memory_region(0, 230686720, BOOT_MEM_RAM) DEBUG_MEM_AUTO: [bsp_prom_memmap]add_memory_region(0x00000000, 0x0dc00000, BOOT_MEM_RAM) DEBUG_MEM_AUTO: [bsp_prom_memmap]add_memory_region(234881024, 24117248, BOOT_MEM_RAM) DEBUG_MEM_AUTO: [bsp_prom_memmap]add_memory_region(0x0e000000, 0x01700000, BOOT_MEM_RAM) [ 0.000000] Initializing cgroup subsys cpuset [ 0.000000] Initializing cgroup subsys cpu [ 0.000000] Initializing cgroup subsys cpuacct [ 0.000000] Linux version 4.4.140 (csdn@csdn-virtual-machine) (gcc version 4.8.5 20150209 (prerelease) (Realtek MSDK-4.8.5p1 Build 3068) ) #4 SMP Sat Aug 31 15:26:45 CST 2024 [ 0.000000] chip Id 0x00009607, 0x96071801 [ 0.000000] MIPS: machine is Realtek Semiconductor RTL8198D [ 0.000000] [L2_DEBUG:(bsp_scache_config,54)] - L2_Bypass: Disable [ 0.000000] [L2_DEBUG:(bsp_setup_scache,82)]SCache LineSize= 32 (B) [ 0.000000] Disable SRAM PLL...done [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001a120 (MIPS interAptiv (multi)) [ 0.000000] MIPS: machine is rtk,9607c [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 0dc00000 @ 00000000 (usable) [ 0.000000] memory: 01700000 @ 0e000000 (usable) [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000f6fffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000dbfffff] [ 0.000000] node 0: [mem 0x000000000e000000-0x000000000f6fffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000f6fffff] [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] PERCPU: Embedded 11 pages/cpu @81238000 s12352 r8192 d24512 u45056 [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 61652 [ 0.000000] Kernel command line: console=ttyS0,115200 ubi.mtd=4 root=31:7 rootfs=squashfs mtdparts=spinand:896K(boot),128K(env),128K(env2),128K(static_conf),127232K(ubi_device) [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes) [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 229872K/248832K available (7985K kernel code, 5139K rwdata, 2328K rodata, 276K init, 349K bss, 18960K reserved, 0K cma-reserved, 0K highmem) [ 0.000000] Hierarchical RCU implementation. [ 0.000000] Build-time adjustment of leaf fanout to 32. [ 0.000000] NR_IRQS:256 [ 0.000000] CPU clock is 1150 [ 0.000000] [apro_clocks_init]clk_data.clk_num=2, ocp=1150000000, lx=200000000 [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0x10939a911d9, max_idle_ns: 440795210078 ns [ 0.000000] sched_clock: 32 bits at 100 Hz, resolution 10000000ns, wraps every 21474836475000000ns [ 0.010000] Console: colour dummy device 80x25 [ 0.010000] Calibrating delay loop... 761.03 BogoMIPS (lpj=3805184) [ 0.050000] pid_max: default: 32768 minimum: 301 [ 0.050000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.060000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.060000] Initializing cgroup subsys io [ 0.070000] Initializing cgroup subsys memory [ 0.070000] Initializing cgroup subsys devices [ 0.070000] Initializing cgroup subsys freezer [ 0.080000] Initializing cgroup subsys debug [ 0.080000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.080000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.080000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.080000] CPU1 revision is: 0001a120 (MIPS interAptiv (multi)) [ 0.140000] Synchronize counters for CPU 1: done. [ 0.140000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.140000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.140000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.140000] CPU2 revision is: 0001a120 (MIPS interAptiv (multi)) [ 0.200000] Synchronize counters for CPU 2: done. [ 0.200000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.200000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.200000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.200000] CPU3 revision is: 0001a120 (MIPS interAptiv (multi)) [ 0.260000] Synchronize counters for CPU 3: done. [ 0.260000] Brought up 4 CPUs [ 0.260000] devtmpfs: initialized [ 0.270000] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.280000] futex hash table entries: 1024 (order: 3, 32768 bytes) [ 0.280000] NET: Registered protocol family 16 [ 0.300000] pm-cps: CPC does not support clock gating [ 0.310000] vgaarb: loaded [ 0.310000] SCSI subsystem initialized [ 0.320000] usbcore: registered new interface driver usbfs [ 0.320000] usbcore: registered new interface driver hub [ 0.330000] usbcore: registered new device driver usb [ 0.330000] clocksource: Switched to clocksource GIC [ 0.340000] NET: Registered protocol family 2 [ 0.340000] TCP established hash table entries: 2048 (order: 1, 8192 bytes) [ 0.350000] TCP bind hash table entries: 2048 (order: 2, 16384 bytes) [ 0.360000] TCP: Hash tables configured (established 2048 bind 2048) [ 0.370000] UDP hash table entries: 256 (order: 1, 8192 bytes) [ 0.370000] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) [ 0.380000] NET: Registered protocol family 1 [ 0.380000] RPC: Registered named UNIX socket transport module. [ 0.390000] RPC: Registered udp transport module. [ 0.400000] RPC: Registered tcp transport module. [ 0.400000] RPC: Registered tcp NFSv4.1 backchannel transport module. [ 0.410000] USB: Using revC phy [ 0.420000] register USB PHY: ehci-phy, RTK USB PHY version: v3.0 (2022.01.05) [ 0.510000] XHCI v3.10 [ 0.540000] register USB PHY: xhci-u2, RTK USB PHY version: v3.0 (2022.01.05) [ 0.540000] XHCI U2 Phy Init [ 0.560000] u3_utmi_wait timeout [ 0.620000] register USB PHY: xhci-u3, RTK USB PHY version: v3.0 (2022.01.05) [ 0.620000] XHCI U3 Phy Init [ 0.650000] [Kthread : luan_watchdog ] init complete! [ 0.650000] ************ Watchdog Setting **************** [ 0.660000] WDT_E=0, (1-enable, 0-disable) [ 0.660000] WDT_CLK_SC=3 [ 0.660000] PH1_TO=31 [ 0.670000] PH2_TO=0 [ 0.670000] WDT_RESET_MODE=0 [ 0.670000] ********************************************** [ 0.680000] ==== Luna Watchdog Regs ===== [ 0.680000] BSP_WDTCNTRR(0xb8003260): 0x00000000 [ 0.690000] BSP_WDTINTRR(0xb8003264): 0x00000000 [ 0.690000] BSP_WDTCTRLR(0xb8003268): 0xe7c00000 [ 0.700000] ================================= [ 0.710000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.710000] ntfs: driver 2.1.32 [Flags: R/W]. [ 0.720000] fuse init (API version 7.23) [ 0.730000] io scheduler noop registered [ 0.730000] io scheduler deadline registered [ 0.730000] io scheduler cfq registered (default) [ 0.740000] rtk-mips-ia-gpio 1b000038.gpio-controller: resource - [mem 0x1b000038-0x1b000043 flags 0x200] mapped at 0xbb000038 [ 0.750000] rtk-mips-ia-gpio 1b000038.gpio-controller: resource - [mem 0x18003308-0x1800335b flags 0x200] mapped at 0xb8003308 [ 0.770000] rtk-mips-ia-gpio 1b000038.gpio-controller: Setting up IRQs for GPIO bank 0 [ 0.770000] rtk-mips-ia-gpio 1b000038.gpio-controller: Setting up IRQs for GPIO bank 1 [ 0.780000] rtk-mips-ia-gpio 1b000038.gpio-controller: Setting up IRQs for GPIO bank 2 [ 0.790000] Realtek GPIO Driver for Flash Reload Default [ 0.850000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.860000] console [ttyS0] disabled [ 0.870000] 18002000.serial: ttyS0 at MMIO 0x18002000 (irq = 46, base_baud = 12327200) is a 16550A [ 0.880000] console [ttyS0] enabled [ 0.880000] console [ttyS0] enabled [ 0.880000] bootconsole [early0] disabled [ 0.880000] bootconsole [early0] disabled [ 0.890000] aipcBoardChipId=0x96070001 aipcBoardChipRev=0x00000003 aipcBoardChipSubType=0x00000018 [ 0.900000] RTL9607C_CHIP_ID 0x96070001 [ 0.910000] CHIP_REV_ID_C 0x00000003 [ 1.010000] aipc: register chrdev(254,0) [ 1.020000] aipc: create device successed [ 1.020000] aipc: start aipc irq init [ 1.020000] aipc: Request IRQ for IPC OK [ 1.030000] aipc: create dsp console device successed [ 1.030000] aipc: init done [ 1.040000] Realtek Luna SPI NAND Flash Driver Rev:00:00:00 (ChaoYuan_Yang) [ 1.040000] [SPINAND] Blocks number under 6 are protected [ 1.050000] [SPINAND] Allow max 4 bits flip in blank page! [ 1.060000] Use RTK bb func [ 1.060000] Use RTK bb scan [ 1.060000] nand: device found, Manufacturer ID: 0xef, Chip ID: 0xaa [ 1.070000] nand: Unknown [ 1.070000] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64 [ 1.140000] good block number 1024 [ 1.140000] 5 cmdlinepart partitions found on MTD device spinand [ 1.150000] RTK: using dynamic nand partition [ 1.150000] Creating 5 MTD partitions on "spinand": [ 1.160000] 0x000000000000-0x0000000e0000 : "boot" [ 1.160000] 0x0000000e0000-0x000000100000 : "env" [ 1.170000] 0x000000100000-0x000000120000 : "env2" [ 1.180000] 0x000000120000-0x000000140000 : "static_conf" [ 1.180000] 0x000000140000-0x000007d80000 : "ubi_device" [ 1.190000] Size of the first partition is 7 blocks. [ 1.200000] Realtek SPINAND Flash Driver is successfully installing. [ 1.200000] Init RTK Driver Module....rtk_switch_irq_init 364 irq=38 name=apl_sw [ 1.300000] phy recovery init complete! version 1.1 [ 1.300000] OK [ 1.310000] Init RTK Core Dev Module....OK [ 1.310000] [ 1.310000] rtdrv_init !!!! for netfilter [ 1.320000] [rtdrv_init]: rtdrv_ext_igmpHook_sockopts init. [ 1.320000] [rtdrv_init]: rtdrv_ext_igmpHook_sockopts success. [ 1.330000] pkt_redirect_init complete [ 1.330000] interrupt broadcaster init ok! [ 1.340000] drivers/net/ethernet/realtek/rtl86900/sdk/src/module/dspbo_queue/dspbo_queue_main.c:284 pDsPboQueueTask complete! [ 1.350000] re8670_set_features 1082: enter [ 1.360000] re8670_set_features 1082: enter [ 1.360000] re8670_set_features 1082: enter [ 1.370000] re8670_set_features 1082: enter [ 1.370000] re8670_set_features 1082: enter [ 1.380000] re8670_set_features 1082: enter [ 1.380000] re8670_set_features 1082: enter [ 1.390000] re8670_set_features 1082: enter [ 1.390000] re8670_set_features 1082: enter [ 1.390000] re8670_set_features 1082: enter [ 1.400000] >>>> Set nas0 carrier off !!! [ 1.440000] Disable gmac[0] padding [ 1.450000] [ 1.450000] rtk_gmac_netdev_init 12348: netdev name=eth0 exist [ 1.470000] Disable gmac[1] padding [ 1.470000] [ 1.470000] rtk_gmac_netdev_init 12348: netdev name=eth0 exist [ 1.490000] Disable gmac[2] padding [ 1.490000] first entry: 0, portmask 2047, rx: 807dd058 [ 1.500000] [FCEXT] rtk_fc_extmodule_init [ 1.520000] [FCMGR] module init, detect 4 cpus online @rtk_fc_mgr_init(645) [ 1.530000] fc_db.controlFuc.external_switch_en = 0 external_switch_port_offset = 0 [ 1.540000] fc_db.controlFuc.mem_leak_debug = 0 fc_db.controlFuc.vlan_filtering = 1 [ 1.550000] fc_db.controlFuc.special_fast_forward_mode = 0 fc_db.controlFuc.hwnat_customize = 0 fc_db.controlFuc.hwnat_customize_nptv6_sram_acc_v2 = 0 [ 2.400000] RTK FleetConntrack Driver - core module init [ 2.410000] - version: dev.0.0 (00000000) 0000-00-00-0000 [ 2.410000] - mem usage 6750 KB (malloc:2111816 fc_db:4799992 pro_db:532) [ 2.420000] priority: 0, portmask 2047, rx: 807dd058 [ 2.420000] insert here, priority: 1, portmask 2047, rx: 807e1ce8 [ 2.430000] priority: 1, portmask 2047, rx: 807e1ce8 [ 2.440000] insert here, priority: 10, portmask 2047, rx: 807e1b88 [ 2.440000] RTK FleetConntrack Driver - manager module init [ 2.450000] - mem usage 88 KB (db:22136 nicrx_ipi:68096) [ 2.460000] rtk_common_utility_init 355 common utility init! [ 2.460000] PPP generic driver version 2.4.2 [ 2.470000] NET: Registered protocol family 24 [ 2.470000] PPTP driver version 0.8.5 [ 2.480000] MPPE/MPPC encryption/compression module registered [ 2.480000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 2.490000] ehci-pci: EHCI PCI platform driver [ 2.490000] ehci-platform: EHCI generic platform driver [ 2.500000] ehci-platform ehci-platform.0: EHCI Host Controller [ 2.510000] ehci-platform ehci-platform.0: new USB bus registered, assigned bus number 1 [ 2.520000] ehci-platform ehci-platform.0: irq 74, io mem 0x18021000 [ 2.540000] ehci-platform ehci-platform.0: USB 2.0 started, EHCI 1.00 [ 2.540000] hub 1-0:1.0: USB hub found [ 2.550000] hub 1-0:1.0: 1 port detected [ 2.550000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 2.560000] ohci-pci: OHCI PCI platform driver [ 2.560000] ohci-platform: OHCI generic platform driver [ 2.570000] ohci-platform ohci-platform.0: Generic Platform OHCI controller [ 2.580000] ohci-platform ohci-platform.0: new USB bus registered, assigned bus number 2 [ 2.590000] ohci-platform ohci-platform.0: irq 74, io mem 0x18020000 [ 2.650000] hub 2-0:1.0: USB hub found [ 2.650000] hub 2-0:1.0: 1 port detected [ 2.660000] xhci-hcd xhci-hcd: xHCI Host Controller [ 2.660000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 3 [ 2.670000] xhci-hcd xhci-hcd: hcc params 0x0220fe6c hci version 0x110 quirks 0x00010010 [ 2.680000] xhci-hcd xhci-hcd: irq 75, io mem 0x18060000 [ 2.690000] hub 3-0:1.0: USB hub found [ 2.690000] hub 3-0:1.0: 1 port detected [ 2.700000] xhci-hcd xhci-hcd: xHCI Host Controller [ 2.700000] xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 4 [ 2.710000] usb usb4: We don't know the algorithms for LPM for this host, disabling LPM. [ 2.720000] hub 4-0:1.0: USB hub found [ 2.720000] hub 4-0:1.0: 1 port detected [ 2.730000] usbcore: registered new interface driver cdc_acm [ 2.730000] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters [ 2.740000] usbcore: registered new interface driver usblp [ 2.750000] usbcore: registered new interface driver uas [ 2.750000] usbcore: registered new interface driver usb-storage [ 2.760000] usbcore: registered new interface driver usbserial [ 2.770000] usbcore: registered new interface driver usbserial_generic [ 2.780000] usbserial: USB Serial support registered for generic [ 2.780000] usbcore: registered new interface driver ftdi_sio [ 2.790000] usbserial: USB Serial support registered for FTDI USB Serial Device [ 2.800000] usbcore: registered new interface driver option [ 2.800000] usbserial: USB Serial support registered for GSM modem (1-port) [ 2.810000] usbcore: registered new interface driver pl2303 [ 2.820000] usbserial: USB Serial support registered for pl2303 [ 2.820000] hidraw: raw HID events driver (C) Jiri Kosina [ 2.830000] usbcore: registered new interface driver usbhid [ 2.840000] usbhid: USB HID core driver [ 2.840000] /proc/slicReadID created [ 2.840000] u32 classifier [ 2.850000] Netfilter messages via NETLINK v0.30. [ 2.850000] nf_conntrack version 0.5.0 (3591 buckets, 14364 max) [ 2.860000] ip_set: protocol 6 [ 2.860000] gre: GRE over IPv4 demultiplexor driver [ 2.870000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 2.870000] NET: Registered protocol family 10 [ 2.880000] ip6_tables: (C) 2000-2006 Netfilter Core Team [ 2.890000] sit: IPv6 over IPv4 tunneling driver [ 2.890000] NET: Registered protocol family 17 [ 2.900000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 2.910000] Bridge firewalling registered [ 2.920000] Ebtables v2.0 registered [ 2.920000] l2tp_core: L2TP core driver, V2.0 [ 2.930000] l2tp_ppp: PPPoL2TP kernel driver, V2.0 [ 2.930000] l2tp_netlink: L2TP netlink interface [ 2.940000] 8021q: 802.1Q VLAN Support v1.8 [ 2.940000] Register system dying gasp...Done [ 2.950000] RTK-PCI Init... [ 2.950000] Using revC phy [ 2.950000] PCIe Port0, PCIe PHY version: v006 (2022.09.30) [ 3.180000] Port0 Link@5.0Ghz [ 3.190000] Port0 link=1 irq=72 [ 3.190000] registering PCI controller with io_map_base unset [ 3.200000] PCI host bridge to bus 0000:00 [ 3.200000] pci_bus 0000:00: root bus resource [mem 0x1a000000-0x1affffff] [ 3.210000] pci_bus 0000:00: root bus resource [io 0x18e00000-0x18e0ffff] [ 3.220000] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 3.220000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 3.230000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.240000] pci 0000:00:01.0: BAR 2: assigned [mem 0x1a000000-0x1a0fffff 64bit] [ 3.250000] pci 0000:00:01.0: BAR 0: assigned [io 0x18e00000-0x18e000ff] [ 3.260000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 3.260000] PCIe Port1, PCIe PHY version: v006 (2022.09.30) [ 3.480000] Port1 Link@2.5GHz [ 3.480000] Port1 link=1 [ 3.490000] registering PCI controller with io_map_base unset [ 3.490000] PCI host bridge to bus 0000:02 [ 3.500000] pci_bus 0000:02: root bus resource [mem 0x19000000-0x19ffffff] [ 3.500000] pci_bus 0000:02: root bus resource [io 0x18c00000-0x18c0ffff] [ 3.510000] pci_bus 0000:02: root bus resource [??? 0x00000000 flags 0x0] [ 3.520000] pci_bus 0000:02: No busn resource found for root bus, will use [bus 02-ff] [ 3.530000] pci 0000:02:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 3.540000] pci 0000:02:01.0: BAR 2: assigned [mem 0x19000000-0x190fffff 64bit] [ 3.540000] pci 0000:02:01.0: BAR 0: assigned [io 0x18c00000-0x18c000ff] [ 3.550000] pci 0000:02:00.0: PCI bridge to [bus 03] [ 3.560000] RTK-PCI Done [ 3.560000] ubi0: attaching mtd4 [ 4.140000] ubi0: scanning is finished [ 4.150000] ubi0: attached mtd4 (name "ubi_device", size 124 MiB) [ 4.150000] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 4.160000] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 4.170000] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 4.180000] ubi0: good PEBs: 994, bad PEBs: 0, corrupted PEBs: 0 [ 4.180000] ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128 [ 4.190000] ubi0: max/mean erase counter: 4/1, WL threshold: 4096, image sequence number: 163500012 [ 4.200000] ubi0: available PEBs: 303, total reserved PEBs: 691, PEBs reserved for bad PEB handling: 20 [ 4.210000] ubi0: background thread "ubi_bgt0d" started, PID 78 [ 4.210000] input: gpio-keys as /devices/platform/gpio-keys/input/input0 [ 4.220000] VoIP control bind 1 (1) instances successfully. [ 4.220000] index dsp_cpuid dsp_cch host_cch [ 4.220000] ----- --------- ------- -------- [ 4.220000] 0 0 0 0 [ 4.220000] voip spin lock init done [ 4.220000] VoIP RX netfilter hook init done! [ 4.220000] VoIP RX netfilter hook for IPv6 init done! [ 4.220000] =============RTK VOIP SUITE============= [ 4.220000] SDK VoIP Version: VoIP-1.6-DSP-R5523-Luna-R24-Integrate_RTL_CA [ 4.220000] Board CFG Model : [ 4.220000] INITIAL VOIP MANAGER PROGRAM [ 4.280000] VFS: Mounted root (squashfs filesystem) readonly on device 31:7. [ 4.290000] devtmpfs: mounted [ 4.300000] Freeing unused kernel memory: 276K Bad inittab entry at line 34 starting pid 86, tty '': '/etc/init.d/rcS' === Start to run rc0 / rc63 === ----- do_rc [/etc/init.d/rc2] ----- [ 4.850000] smuxdev: loading out-of-tree module taints kernel. [ 4.860000] smuxdev: loaded WARN: conflicting configurations in /etc/fstab and /etc/default/rcS regarding the writability of rootfs. Please fix one of them. [ 5.280000] UBIFS (ubi0:0): background thread "ubifs_bgt0_0" started, PID 116 [ 5.320000] UBIFS (ubi0:0): recovery needed [ 5.440000] UBIFS (ubi0:0): recovery completed [ 5.440000] UBIFS (ubi0:0): UBIFS: mounted UBI device 0, volume 0, name "ubi_Config" [ 5.450000] UBIFS (ubi0:0): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes [ 5.460000] UBIFS (ubi0:0): FS size: 9777152 bytes (9 MiB, 77 LEBs), journal size 1015809 bytes (0 MiB, 6 LEBs) [ 5.470000] UBIFS (ubi0:0): reserved for root: 461798 bytes (450 KiB) [ 5.480000] UBIFS (ubi0:0): media format: w4/r0 (latest is w4/r0), UUID 2259E028-6D19-4CF7-AA8D-D1DC004AE3CB, small LPT model ----- do_rc [/etc/init.d/rc3] ----- [ 5.650000] tv_sec:5 tv_usec:650043 [ 5.650000] CPU0 kick watchdog! set_msgqueue_max_size:417> set msgqidds.msg_qbytes=36000 OK set_msgqueue_max_size:417> set msgqidds.msg_qbytes=36000 OK [ 6.630000] aipc: (0420)prepare_BIR aipc: write image successful. size=2881648 rc=2881648 wc=2881648[ 7.000000] aipc: (0518)aipc_dev_ioctl boot dsp da=0xb02c0400 remain=0 [ 7.010000] aipc: (0520)aipc_dev_ioctl boot dsp done Wait DSP 0/1 booting ...... .[ 7.530000] aipc: (0617)aipc_dsp_disable_mem Wait DSP ok. wait_cnt=1 DSP 0 Software Ready! rtkbosa: Donât care pon mode, use general file cat: can't open '/var/config/rtkbosa_k_checksum': No such file or directory rtkbosa: checksumold = rtkbosa: Use general file [/var/config/rtkbosa_k.bin] [1;33;46mrtkbosa: Version 2.15 (Aug 31 2024 - 09:49:41)[m rtkbosa: Detecting RTL8290B ... rtkbosa: Error (0x10): The chip is not found rtkbosa: Detecting UX3320_S ... rtkbosa: Detecting UX3360 ... rtkbosa: Detecting UX3361 ... rtkbosa: Detecting Semtech Series (GN2xL9x) ... rtkbosa: Detecting Semtech Bosa ID ... [1;33;46mrtkbosa: SEMTECH GN25L95 is Found[m rtkbosa: EEPROM exists, bosa should be working. [1;33;46mrtkbosa: done[m diable printk= 0 parameter is 1 /etc/init.d/rc3: line 8: /bin/checkomci: not found grep: /config/default_scfg.txt: No such file or directory RTL Chip............ Loading modules: ca-ne ca-plat-kernel ca-sdk-cb libscfg [ 8.780000] Loading modules backported from Linux version v5.2.8-0-gd36a8d2fb62c [ 8.790000] Backport generated by backports.git v5.2.8-1-0-ga33d4e95 [ 8.890000] cfg80211: Loading compiled-in X.509 certificates for regulatory database [ 8.910000] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7' [ 9.680000] random: nonblocking pool is initialized [ 10.650000] tv_sec:10 tv_usec:650097 [ 10.650000] luna_watchdog: luna_watchdog/1 not respond! [ 10.690000] PCI: Enabling device 0000:00:01.0 (0000 -> 0003) [ 10.690000] devfn:8 vend:10ec dev:b832 cls:28000 pin:1 [ 10.700000] [rtw_dev_probe] dev_probe_num:1 padapter:0x (null) dev_id:0 [ 10.710000] PHL: Use chip layer register read functions! [ 10.720000] PHL: [MAC] MAC_AX_MAJOR_VER = 0 [ 10.720000] MAC_AX_PROTOTYPE_VER = 27 [ 10.720000] MAC_AX_SUB_VER = 75 [ 10.720000] MAC_AX_SUB_INDEX = 0 [ 10.730000] PHL: [MAC] [ERR]Access efuse in suspend [ 10.740000] PHL: [MAC] fv = 0 [ 10.750000] dbg [rtw_hal_mac_init][1065]chip_cut = 0 [ 10.760000] [phl_trx_init_pcie:2756] init lock rx_buf_info_lock [ 10.770000] PHL: CH[0] Alloc 8080B RX buffer, got available size 8096B [ 10.780000] PHL: CH[1] Alloc 400B RX buffer, got available size 416B [ 10.800000] eric-tx CALL alloc_txring !!!! [ 10.830000] swq tasklet init padapter=c162d000 dvobj=8c170000 [ 10.830000] padapter=c162d000 dvobj=8c170000 [ 10.860000] eric-tx CALL alloc_txring !!!! [ 10.870000] padapter=c1b0c000 dvobj=8c170000 [ 10.890000] eric-tx CALL alloc_txring !!!! [ 10.900000] padapter=c1dcc000 dvobj=8c170000 [ 10.930000] eric-tx CALL alloc_txring !!!! [ 10.930000] padapter=c208c000 dvobj=8c170000 [ 10.960000] eric-tx CALL alloc_txring !!!! [ 10.960000] padapter=c234c000 dvobj=8c170000 [ 10.990000] eric-tx CALL alloc_txring !!!! [ 11.000000] padapter=c260c000 dvobj=8c170000 [ 11.000000] dbg [rtw_build_he_phy_caps][782]force enable RX ldpc [ 11.010000] dbg [rtw_build_he_phy_caps][794]no RX stbc [ 11.010000] dbg [rtw_build_he_phy_caps][782]force enable RX ldpc [ 11.020000] dbg [rtw_build_he_phy_caps][794]no RX stbc [ 11.030000] dbg [rtw_cfg80211_init_wiphy][10864]enable A4 [ 11.040000] PCI: Enabling device 0000:02:01.0 (0000 -> 0003) [ 11.050000] devfn:8 vend:10ec dev:192 cls:28000 pin:1 [ 11.060000] [rtw_dev_probe] dev_probe_num:2 padapter:0x (null) dev_id:1 [ 11.070000] PHL: Use chip layer register read functions! [ 11.080000] PHL: [MAC] MAC_AX_MAJOR_VER = 0 [ 11.080000] MAC_AX_PROTOTYPE_VER = 27 [ 11.080000] MAC_AX_SUB_VER = 75 [ 11.080000] MAC_AX_SUB_INDEX = 0 [ 11.090000] PHL: [MAC] [ERR]Access efuse in suspend [ 11.100000] PHL: [MAC] fv = 0 [ 11.100000] dbg [rtw_hal_mac_init][1065]chip_cut = 0 [ 11.120000] [phl_trx_init_pcie:2756] init lock rx_buf_info_lock [ 11.130000] PHL: CH[0] Alloc 3984B RX buffer, got available size 4000B [ 11.140000] PHL: CH[1] Alloc 400B RX buffer, got available size 416B [ 11.160000] eric-tx CALL alloc_txring !!!! [ 11.180000] swq tasklet init padapter=c2cca000 dvobj=88270000 [ 11.190000] padapter=c2cca000 dvobj=88270000 [ 11.220000] eric-tx CALL alloc_txring !!!! [ 11.220000] padapter=c3195000 dvobj=88270000 [ 11.250000] eric-tx CALL alloc_txring !!!! [ 11.260000] padapter=c3455000 dvobj=88270000 [ 11.280000] eric-tx CALL alloc_txring !!!! [ 11.290000] padapter=c3715000 dvobj=88270000 [ 11.320000] eric-tx CALL alloc_txring !!!! [ 11.320000] padapter=c39d5000 dvobj=88270000 [ 11.350000] eric-tx CALL alloc_txring !!!! [ 11.350000] padapter=c3c95000 dvobj=88270000 [ 11.360000] dbg [rtw_build_he_phy_caps][782]force enable RX ldpc [ 11.370000] dbg [rtw_build_he_phy_caps][794]no RX stbc [ 11.370000] dbg [rtw_build_he_phy_caps][782]force enable RX ldpc [ 11.380000] dbg [rtw_build_he_phy_caps][794]no RX stbc [ 11.380000] dbg [rtw_cfg80211_init_wiphy][10864]enable A4 find: /lib/modules/users/: No such file or directory [ 11.490000] re8670_open 6135 [ 11.490000] re8670_open 6139 [ 11.510000] re8670_open 6139 [ 11.520000] re8670_open 6139 Unix Socket Connect to server failed!!!: No such file or directory Unable to open unix socket file /var/run/systemd.usock!!! [ 11.800000] pf_rt_fc: unknown parameter 'pon_speed' ignored [ 11.830000] register_gpon_evt_state: register gpon event state Successfully ! [ 11.830000] omci platform db suc! [ 11.840000] ponPort:5 cpuPort:9 rgmiiPort:8 uniPortMask:0x20f etherPortMask:0xf [ 11.840000] omci platform attached! Loading TR-142 Module... [ 11.880000] Realtek TR-142 Module initialized. [ 11.990000] [rtk_tr142_nl_recv_msg] rtk_tr142_nl_pid = 371 [ 12.000000] Set mapping_outermost_vlan_by_mac_from_lut to 0 OK. TR142_FEATURE_API_INIT_LIB ret = 0 [rtk_tr142_debug_log_set] log_enable = 0 tr142_app app_log_enable = 0 [ 12.220000] IPv6: eth0: IPv6 duplicate address fe80::200:ff:fe01:2 detected! running GPON mode ... insmod: can't insert '/lib/modules/rldp_drv.ko': No such file or directory Loading Realtek IGMP/ MLD Snooping Module... [ 12.430000] multicast_moudle_init ----- do_rc [/etc/init.d/rc6] ----- ----- do_rc [/etc/init.d/rc10] ----- ----- do_rc [/etc/init.d/rc14] ----- ----- do_rc [/etc/init.d/rc18] ----- ----- do_rc [/etc/init.d/rc20] ----- ----- do_rc [/etc/init.d/rc32] ----- ----- do_rc [/etc/init.d/rc34] ----- run rcm voip script... ponmode PON_MODE=1 Start rtk_ramonitor daemon! write watchdog_flag to 0x00000001 REG32(BSP_WDTCTRLR) = 0xe7c00000 ----- do_rc [/etc/init.d/rc35] -Inactive PIN_CS: ---- argc 1, sl icinitpower 1 <<<<<<<<<<< Si3219x Driver Version 10.0.1 >>>>>>>>>> ------------------------------ SLIC 32192 HW intf 0 CS=0 aipc: (0296)aipc_module_voip_set_pcm_fs IO_MODE_EN=0x0000a050 Pull high GPIO 28 [setup_usock_thread:6559] Create new theread for usock [setup_pushbtn_thread:5854] Create new theread for pushbtn Input driver version is 1.0.1 Input device ID: bus 0x19 vendor 0x1 product 0x1 version 0x100 Input device name: "gpio-keys" Supported events: Event type 0 (Sync) EReset value to -1 vent type 1 (Key) Event code 238 Event code 408 Event code 529 Event type 20 (Repeat) Grab succeeded, ungrReset value to -1 abbing. Reset value to -1 Reset value to -1 Reset value to -1 Reset value to -1 Turn on phy power... Reset value to -1 Reset value to -1 Reset value to -1 diable printk= 0 parameter is 0 Reset value to -1 Set svlan tpid ptn = 0x8100 to stag[0] Set svlan tpid ptn = 0x88a8 to stag[1] 4 cpu Pull low GPIO 28 >> HWNAT customize was not enabled, do nothing << 0 starting pid 577, tty '/dev/ttyS0': '/bin/login -p' WLAN0 Dispatch mode: 0, cpu: 0 starting pid 580, tty '': '/bin/inetd' WLAN1 Dispatch mode: 0, cpu: 0 login: service /bin/ftpd port 21 tcp enabled service /bin/telnetd port 23 tcp enabled Pull high GPIO 28 Start SLIC init.... meter set pon-tick-token tick-period 73 token 97 cs0 MSIF_LOCK 0x1, cs 0x0 Start SLIC init.... RTK.0> command:[rtk_qos_tick_tocken_init:254] Enable 9607C 8000Kbps base !! meter set tick-token tick-period 71 token 151 RTK.0> command:register set 0x801030 0x80004797 RTK.0> command:1 sh: can't create /proc/fc/ctrl/fc_flow_l2_skipPsTracking: nonexistent directory bit mask = 0x20, action = drop bit mask = 0x20, action = forward Error: cannot open /sys/class/net/eth0.2.0/ifindex Error: cannot open /sys/class/net/eth0.3.0/ifindex Error: cannot open /sys/class/net/eth0.4.0/ifindex Error: cannot open /[rtk_tr142_veip_get_transparent_ifIndex] ifIndex = 0 sys/class/net/eth0.5.0/ifindex CMD: /bin/sh -c /bin/echo 5 nas0 > /proc/eth_nic/dev_port_mapping port 5 assign to nas0 CMD: /bin/sh -c echo 0x20 > /proc/fc/ctrl/wan_port_mask CMD: /bin/smuxctl --if nas0 --set-if-rsmux --set-if-rx-policy DROP --set-if-tx-policy CONTINUE --set-if-rxmc-policy DROP --set-if-rx-multi 1 CMD: /bin/sh -c echo auto_reserve_vlan 1 > prSet auto_reserve_vlan to 1 OK. oc/rtk_smuxdev/configure MIB chain descriptors checking (total 68) ok ! [1;33;46m<utility.c 991 setup_mac_addr> [mmacAddr[5]+1 = 25 CMD: /bin/mkdir -p /var/network No need to update wan user name and password. >>> Disable /dev/console XON XOFF !!! CMD: /bin/touch /var/wan_sockmark_file CMD: /bin/ifconfig eth0.2 hw ether 60d2dd63c424 CMD: /bin/ifconfig eth0.3 hw ether 60d2dd63c424 CMD: /bin/ifconfig eth0.4 hw ether 60d2dd63c424 CMD: /bin/ifconfig eth0.5 hw ether 60d2dd63c424 [1;33;46m<utility.c 991 setup_mac_addr> [mmacAddr[5]+1 = 25 CMD: /bin/ifconfig wlan0 hw ether 60d2dd63c425 CMD: /bin/ifconfig wlan0 mtu 1500 [1;33;46m<utility.c 991 setup_mac_addr> [mmacAddr[5]+1 = 26 CMD: /bin/ifconfig wlan0-vap0 hw ether 60d2dd63c426 ifconfig: SIOCSIFHWADDR: No such device CMD: /bin/ifconfig wlan0-vap0 mtu 1500 ifconfig: SIOCSIFMTU: No such device [1;33;46m<utility.c 991 setup_mac_addr> [mmacAddr[5]+1 = 27 CMD: /bin/ifconfig wlan0-vap1 hw ether 60d2dd63c427 ifconfig: SIOCSIFHWADDR: No such device CMD: /bin/ifconfig wlan0-vap1 mtu 1500 ifconfig: SIOCSIFMTU: No such device [1;33;46m<utility.c 991 setup_mac_addr> [mmacAddr[5]+1 = 28 CMD: /bin/ifconfig wlan0-vap2 hw ether 60d2dd63c428 ifconfig: SIOCSIFHWADDR: No such device CMD: /bin/ifconfig wlan0-vap2 mtu 1500 ifconfig: SIOCSIFMTU: No such device [1;33;46m<utility.c 991 setup_mac_addr> [mmacAddr[5]+1 = 29 CMD: /bin/ifconfig wlan0-vap3 hw ether 60d2dd63c429 ifconfig: SIOCSIFHWADDR: No such device CMD: /bin/ifconfig wlan0-vap3 mtu 1500 ifconfig: SIOCSIFMTU: No such device [1;33;46m<utility.c 991 setup_mac_addr> [mmacAddr[5]+1 = 2a CMD: /bin/ifconfig wlan1 hw ether 60d2dd63c42a CMD: /bin/ifconfig wlan1 mtu 1500 [1;33;46m<utility.c 991 setup_mac_addr> [mmacAddr[5]+1 = 2b CMD: /bin/ifconfig wlan1-vap0 hw ether 60d2dd63c42b ifconfig: SIOCSIFHWADDR: No such device CMD: /bin/ifconfig wlan1-vap0 mtu 1500 ifconfig: SIOCSIFMTU: No such device [1;33;46m<utility.c 991 setup_mac_addr> [mmacAddr[5]+1 = 2c CMD: /bin/ifconfig wlan1-vap1 hw ether 60d2dd63c42c ifconfig: SIOCSIFHWADDR: No such device CMD: /bin/ifconfig wlan1-vap1 mtu 1500 ifconfig: SIOCSIFMTU: No such device [1;33;46m<utility.c 991 setup_mac_addr> [mmacAddr[5]+1 = 2d CMD: /bin/ifconfig wlan1-vap2 hw ether 60d2dd63c42d ifconfig: SIOCSIFHWADDR: No such device CMD: /bin/ifconfig wlan1-vap2 mtu 1500 ifcSLIC0 ID: onfig: SIOCSIFMTregvalue = aa U: No such devicSi32192 e [1;33;46m<utRevision A ility.c 991 setuSi3219x_Init_with_Options(607) size = 1 init_opt = 0 p_mac_addr> [mmacAddr[5]+1 = 2eport 0 CMD: /bin/iassign to eth0.2 fconfig wlan1-vaSiVoice: Channel 0: Type = PROSLIC Rev = 2 ProSLIC:loading patch: 05252017 p3 hw ether 60d2dd63c42e ifconfig: SIOCSIFHWADDR: No such device CMD: /bin/ifconfig wlan1-vap3 mtu 1500 ifconfig: SIOCSIFMTU: No such device CMD: /bin/ifconfig eth0 up CMD: /bin/ifconfig eth0 mtu 1500 CMD: /bin/sh -c /bin/echo 0 eth0.2 > /proc/eth_niport 1 assign to eth0.3 c/dev_port_mapping CMD: /bin/ifconfig eth0.2 up CMD: /bin/ifconfig eth0.2 mtu 1500 CMD: /bin/smuxctl --if-create-name eth0.2 eth0.2.0 --set-if-rsmux CMD: /bin/smuxctl --if eth0.2 --rx --tags 0 --set-rxif eth0.2.0 --rule-alias eth0.2-rx-default --rule-aport 2 assign to eth0.4 ppend CMD: /bin/sh -c /bin/echo 1 eth0.3 > /proc/eth_nic/dev_port_mapping CMD: /bin/ifconfig eth0.3 up CMD: /bin/ifconfig eth0.3 mtu 1500 CMD: /bin/smuxctl --if-create-name eth0.3 eth0.3.0 --set-if-rsmux CMD: /bin/smuxctl --if eth0.3 --rx --tags 0 --set-rxif eth0port 3 assign to eth0.5 .3.0 --rule-alias eth0.3-rx-default --rule-append CMD: /bin/sh -c /bin/echo 2 eth0.4 > /proc/eth_nic/dev_port_mapping CMD: /bin/ifconfig eth0.4 up CMD: /bin/ifconfig eth0.4 mtu 1500 CMD: /bin/smuxctl --if-create-name eth0.4 eth0.4.0 --set-if-rsmux CMD: /bin/smuxctl --if eth0.4 --rx --tags 0 --set-rxif eth0.4.0 --rule-alias eth0.4-rx-default --rule-append CMD: /bin/sh -c /bin/echo 3 eth0.5 > /proc/eth_nic/dev_port_mapping CMD: /bin/ifconfig eth0.5 up CMD: /bin/ifconfig eth0.5 mtu 1500 CMD: /bin/smuxctl --if-create-name eth0.5 eth0.5.0 --set-if-rsmux CMD: /bin/smuxctl --if eth0.5 --rx --tags 0 --set-rxif eth0.5.0 --rule-alias eth0.5-rx-default --rule-append CMD: /bin/brctl addbr br0 CMD: /bin/ifconfig br0 hw ether 60d2dd63c424 CMD: /bin/ifconfig br0 mtu 1500 CMD: /bin/ifconfig eth0 hw ether 60d2dd63c424 ifconfig: SIOCSIFHWADDR: Device or resource busy CMD: /bin/sh -c echo 1 > /proc/sys/net/ipv4/conf/br0/rp_filter [rtk_fc_stp_clean@3664]: ERROR! No such file or directory [rtk_fc_stp_clean@3676]: ERROR! No such file or directory CMD: /bin/sh -c /bin/smuxctl --if eth0.2 --rx --tags 0 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.2 --tx --tags 0 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.2 --rx --tags 1 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.2 --tx --tags 1 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.2 --rx --tags 2 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.2 --tx --tags 2 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.3 --rx --tags 0 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.3 --tx --tags 0 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.3 --rx --tags 1 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.3 --tx --tags 1 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.3 --rx --tags 2 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.3 --tx --tags 2 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.4 --rx --tags 0 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.4 --tx --tags 0 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.4 --rx --taSi3219x: Channel 0 : VBAT Up = 59.322 v gs 1 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.4 --tx --tags 1 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.4 --rx --tags 2 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.4 --tx --tags 2 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/sdevice eth0.2.0 entered promiscuous mode muxctl --if eth0.5 --rx --tags 0 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.5 --tx --tags 0 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.5 --rx --tags 1 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.5 --tx --tags 1 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.5 --rx --tags 2 --rule-remove-alias STP-Rule+ CMD: /bin/sh -c /bin/smuxctl --if eth0.5 --tx --tags 2 --rule-remove-alias STP-Rule+ CMD: /bin/brctl stp br0 off CMD: /bin/brctl setfd br0 1 CMD: /bin/brctl setageing br0 7200 setupUniPortCapability:930 line is 2;2;2;2 setupUniPortCapability:934 pch is 2 setupUniPortCapability:1014 pch is 2, port 0, UNI_PORT_GE setupUniPortCapability:934 pch is 2 setupUniPortCapability:1014 pch is 2, port 1, UNI_PORT_GE setupUniPortCapability:934 pch is 2 setupUniPortCapability:1014 pch is 2, port 2, UNI_PORT_GE setupUniPortCapability:934 pch is 2 setupUniPortCapability:1014 pch is 2 , port 3, UNI_PORT_GE CMD: /bin/ifconfig eth0.2.0 mtu 1500 CMD: /bin/brctl addif br0 eth0.2.0 CMD: /bin/ifconfig eth0.2.0 down CMD: /bin/ifconfig eth0.2 down ProSLIC:Starting LB Cal on channel 0 SLIC0 master state check pass! SLIC PCM Setup for CH0 ...ProSLIC:PCMStart OK Set to LF_FWD_ACTIVE Init OK! <<<<<<<<<<<<<<<<<<<<<<<<>>>>>>>>>>>>>>>>>>>>>> All DSP Software Ready. VoIP Defer Init done. start watch dog CMD: /bin/ifconfig eth0.2.0 up CMD: /bin/ifconfig eth0.2 up [restart_ethernet@16821] eth0.2.0 is up getUniPortCapability:1120 line is 2;2;2;2 getUniPortCapability:1127 pch is 2, port is 0 CMD: /bin/ifconfig eth0.3.0 mtu 1500 CMD: /bin/brctl addif br0 eth0.3.0 device eth0.3.0 entered promiscuous mode CMD: /bin/ifconfig eth0.3.0 down CMD: /bin/ifconfig eth0.3 down Testing ... (interrupt to exit) CMD: /bin/ifconfig eth0.3.0 up CMD: /bin/ifconfig eth0.3 up [restart_ethernet@16821] eth0.3.0 is up getUniPortCapability:1120 line is 2;2;2;2 getUniPortCapability:1127 pch is 2, port is 1 CMD: /bdevice eth0.4.0 entered promiscuous mode in/ifconfig eth0.4.0 mtu 1500 CMD: /bin/brctl addif br0 eth0.4.0 CMD: /bin/ifconfig eth0.4.0 down CMD: /bin/ifconfig eth0.4 down /var/config/omci_ignore_mib_tbl.conf meClassId:255 /var/config/omci_ignore_mib_tbl.conf subType:0 /var/config/omci_ignore_mib_tbl.conf meClassId:247 /var/config/omci_ignore_mib_tbl.conf subType:0 /var/config/omci_ignore_mib_tbl.conf meClassId:65305 /var/config/omci_ignore_mib_tbl.device eth0.5.0 entered promiscuous mode conf subType:0 /var/config/omci_ignore_mib_tbl.conf meClassId:65417 /var/config/omci_ignore_mib_tbl.conf subType:0 /var/config/omci_ignore_mib_tbl.conf meClassId:65427 /var/config/omci_ignore_mib_tbl.conf subType:0 <fMgmtInit:601> is the so is not a regular file. <fMgmtInit:601> is the so is not a regular file. <fMgmtInit:601> is the so is not a regular file. CMD: /bin/ifconfig eth0.4.0 up CMD: /bin/ifconfig eth0.4 up [restart_ethernet@16821] eth0.4.0 is up getUniPortCapability:1120 line is 2;2;2;2 getUniPortCapability:1127 pch is 2, port is 2 CMD: /bin/ifconfig eth0.5.0 mtu 1500 [libtr142][OMCI] == libomcitr142.so is loaded == CMD: /bin/brctl addif br0 eth0.5.0 [rtk_omcitr142_debug_log_set] log_enable = 0 Module libomcitr142.so is loaded and inited Module libomcivoip.so is loaded and inited CMD: /bin/ifconfig eth0.5.0 down CMD: /bin/ifconfig eth0.5 down stat failed: /lib/features/internal/bdp_00000002.so load moduleOptInitFunc Module /lib/features/internal/bdp_00000080.so is inited CMD: /bin/ifconfig eth0.5.0 up Module /lib/features/internal/me_00040000.so is inited CMD: /bin/ifconfig eth0.5 up [restart_ethernet@16821] eth0.5.0 is up getUniPortCapability:1120 line is 2;2;2;2 getUniPortCapability:1127 pch is 2 , port is 3 CMD: /bin/sh -c echo 4 > /proc/sys/net/ipv6/conf/br0/dad_transmits ####################### vIPv6: ADDRCONF(NETDEV_UP): br0: link is not ready oice_rtk_init_voip_cfg() ####################### voip omci line state share size = 1152 codec_suporrt_list 1279 CMD: /bin/ifconfig br0 up ### voice_rtk_init_voip_cfg()###, pFlash=0x77993c18, g_pLineState=0x779ba000 CMD: /bin/ifconfig br0 192.168.0.1 netmask 255.255.255.0 mtu 1500 [1;33;46m<subr_net.c 12965 set_ipv4_lan_policy_route> [mSet IPv4 LAN route for ifname (br0), table(260) Auto Link-Local Address for br0 CMD: /bin/sh -c echo 0 > /proc/sys/net/bridge/bridge-nf-call-arptables CMD: /bin/sh -c echo 0 > /proc/sys/net/bridge/bridge-nf-call-iptables CMD: /bin/sh -c echo 0 > /proc/sys/net/bridge/bridge-nf-call-ip6tables CMD: /bin/sh -c echo 1 > /sys/class/net/br0/bridge/nf_call_arptables CMD: /bin/sh -c echo 1 > /sys/class/net/br0/bridge/nf_call_iptables omci_wrapper_msgHandler: devMode 1,receiveState 1,usrLogLvl 1, drvLogLmode=0 , rtk_op_mode = 0 vl 1,sn XPONÝcÄ$ CMD: /bin/sh -c echo 1 > /sys/class/net/br0/bridge/nf_call_ip6tables startELan fail, plz check! CMD: /bin/spppd drivers/net/ethernet/realtek/rtl86900/sdk/src/rtk/pon_led.c:1812 led sw blink init complete! rtk_pon_led_SpecType_set 0 CMD: /bin/sh -c /bin/ip rule add from all lookup 257 pref 27900 CMD: /bin/sh -c /bin/ip rule add from all lookup 260 pref 28000 Ignore classId:65417 MIB_Table_Init Init mib table:mib_ExtendedIpHostCfgData_65417.so fail, error code is:1... CMD: /bin/sh -c /bin/ip -6 rule add from all lookup 257 pref 27900 iptables: Bad rule (does a matching rule exist in that chain?). CMD: /bin/sh -c /bin/ip -6 rule add from all lookup 260 pref 28000 CMD: /bin/sh -c /bin/ip -6 rule add from all lookup 259 pref 27950 CMD: /bin/sh -c /bin/ip -6 rule add from all lookup 258 pref 27945 do_restart_dnsrelay:4389 no delay dns [1;33;46m<subr_net.c 27063 startWan> [mstartWan Start all WAN [update_monitor_list_file:23737] process_name = dnsmasq, action = 0 Open file /var/tmp/hosts failed ! CMD: /bin/ifconfig nas0 hw ether 60d2dd63c424 CMD: /bin/ifconfig nas0 up CMD: /bin/ifconfig nas0 mtu 1500 CMD: /bin/ethtool -k nas0 gso on ethtool: bad command line argument(s) For more information run ethtool -h CMD: /bin/ifconfig nas0 mtu 1500 [update_monitor_list_file:23737] process_name = dnsmasq, action = 1 MIB_Table_Init Init mib table:mib_Me242.so fail, error code is:1... MIB_Table_Init Init mib table:mib_Me243.so fail, error code is:1... CMD: /bin/sh -c /bin/smuxctl --if-create-name nas0 nas0_0 --set-if-rsmux --carrier MANUAL MIB_Table_Init Init mib table:mib_Me350.so fail, error code is:1... MIB_Table_Init Init mib table:mib_Me370.so fail, error code is:1... MIB_Table_Init Init mib table:mib_Me373.so fail, error code is:1... CMD: /bin/sh -c /bin/smuxctl --if nas0_0 --rx --tags 1 --filter-vid 0x2d0 1 --pop-tag --rule-priority 900 --rule-alias nas0_0-rx-default-leaf --rule-append Ignore classId:65305 MIB_Table_Init Init mib table:mib_Me65305.so fail, error code is:1... CMD: /bin/sh -c /bin/smuxctl --if nas0_0 --rx --tags 2 --filter-vid 0x2d0 2 --pop-tag --rule-priority 900 --rule-alias nas0_0-rx-default-leaf --rule-append Ignore classId:65427 MIB_Table_Init Init mib table:mib_Me65427.so fail, error code is:1... ==> [addEthWANdev] /bin/smuxctl --if nas0_0 --tx --tags 0 --push-tag --set-vid 0x2d0 1 --target ACCEPT --rule-alias nas0_0-tx-default --rule-append CMD: /bin/sh -c /bin/smuxctl --if nas0_0 --tx --tags 0 --push-tag --set-vid 0x2d0 1 --target ACCEPT --rule-alias nas0_0-tx-default --rule-append ==> [addEthWANdev] /bin/smuxctl --if nas0_0 --tx --tags 1 --set-vid 0x2d0 1 --target ACCEPT --rule-alias nas0_0-tx-default --rule-append CMD: /bin/sh -c /bin/smuxctl --if nas0_0 --tx --tags 1 --set-vid 0x2d0 1 device nas0_0 entered promiscuous mode --target ACCEPT --rule-alias nas0_0-tx-default --rule-append ==> [addEthWANdev] /bin/smuxctl --if nas0_0 --tx --tags 2 --set-vid 0x2d0 2 --target ACCEPT --rule-alias nas0_0-tx-default --rule-append CMD: /bin/sh -c /bin/smuxctl --if nas0_0 --tx --tags 2 --set-vid 0x2d0 2 --target ACCEPT --rule-alias nas0_0-tx-default --rule-append cmdStr: echo 130816 1 720 -1 2 -1 0 0 > /proc/rtk_tr142/wan_info CMD: /bin/ifconfig nas0_0 down CMD: /bin/ifconfig nas0_0 down hw ether CMD: /bin/ifconfig nas0_0 txqueuelen 10 CMD: /bin/ifconfig nas0_0 up CMD: /bin/mkdir -p /var/network/if-up.d CMD: /bin/mkdir -p /var/network/if-down.d [startConnection@24884] pEntry->ifIndex = 130816, pEntry->cmode = 0 1483 bridged CMD: /bin/brctl addif br0 nas0_0 CMD: /bin/ip rule del fwmark 0x2000/0x7e000 prohibit RTNETLINK answers: No such file or directory CMD: /bin/ip rule add fwmark 0x2000/0x7e000 pref 30000 prohibit CMD: /bin/ip -6 rule del fwmark 0x2000/0x7e000 prohibit RTNETLINK answers: No such file or directory CMD: /bin/ip -6 rule add fwmark 0x2000/0x7e000 pref 30000 prohibit sh: can't create /proc/br_igmpsnoop: nonexistent directory sh: can't create /proc/br_igmpquery: nonexistent directory sh: can't create /proc/br_mldsnoop: nonexistent directory sh: can't create /proc/br_mldquery: nonexistent directory Ignore classId:255 SubType:0 MIB_Table_Init Init mib table:mib_PrivateTellionOntStatistics.so fail, error code is:1... CMD: /bin/sh -c echo 0 > /proc/fc/ctrl/igmp_unknown_flood Usage: Enable unkown multicast data flooding: echo 1 > proc/fc/ctrl/igmp_unkonwn_flood Disable unkown multicast data flooding: echo 0 > proc/fc/ctrl/igmp_unkonwn_flood status:disable Ignore classId:345,only support on G.987 ONU MIB_Table_Init Init mib table:mib_XgponDsMangPMHD.so fail, error code is:1... Ignore classId:344,only support on G.987 ONU MIB_Table_Init Init mib table:mib_XgponTcPMHD.so fail, error code is:1... Ignore classId:346,only support on G.987 ONU MIB_Table_Init Init mib table:mib_XgponUsMangPMHD.so fail, error code is:1... IGMP Snooping: enabled MLD Snooping: enabled CMD: /bin/ebtables -D br_lan_forward -p IPv4 --ip-proto igmp -j BR_IGMP_MLD_DROP Chain 'br_lan_forward' doesn't exist. CMD: /bin/ebtables -D br_lan_forward -p IPv6 --ip6-proto ipv6-icmp --ip6-icmp-type 143:143/0:255 -j BR_IGMP_MLD_DROP Chain 'br_lan_forward' doesn't exist. CMD: /bin/ebtables -D br_lan_forward -p IPv6 --ip6-proto ipv6-icmp --ip6-icmp-type 130:132/0:255 -j BR_IGMP_MLD_DROP Chain 'br_lan_forward' doesn't exist. CMD: /bin/ebtables -F BR_IGMP_MLD_DROP Chain 'BR_IGMP_MLD_DROP' doesn't exist. CMD: /bin/ebtables -X BR_IGMP_MLD_DROP Chain 'BR_IGMP_MLD_DROP' doesn't exist. CMD: /bin/ebtables -N BR_IGMP_MLD_DROP CMD: /bin/ebtables -P BR_IGMP_MLD_DROP RETURN CMD: /bin/ebtables -A BR_IGMP_MLD_DROP -i eth+ -o eth+ -j DROP CMD: /bin/ebtables -A BR_IGMP_MLD_DROP -i eth+ -o wlan+ -j DROP CMD: /bin/ebtables -A BR_IGMP_MLD_DROP -i wlan+ -o eth+ -j DROP CMD: /bin/ebtables -A BR_IGMP_MLD_DROP -i wlan+ -o wlan+ -j DROP CMD: /bin/ebtables -A br_lan_forward -p IPv4 --ip-proto igmp -j BR_IGMP_MLD_DROP Chain 'br_lan_forward' doesn't exist. CMD: /bin/ebtables -A br_lan_forward -p IPv6 --ip6-proto ipv6-icmp --ip6-icmp-type 143:143/0:255 -j BR_IGMP_MLD_DROP Chain 'br_lan_forward' doesn't exist. CMD: /bin/ebtables -A br_lan_forward -p IPv6 --ip6-proto ipv6-icmp --ip6-icmp-type 130:132/0:255 -j BR_IGMP_MLD_DROP Chain 'br_lan_forward' doesn't exist. enter pptp video Ani enter pptp video uni catv mib init!!!!!!!!!!!! CMD: /bin/iptables -t nat -N address_map_tbl CMD: /bin/ip6tables -t nat -N address_map_tbl [restart_upnp:20505] miniupnpd parameter error! (parameter=0, 1, 130816, 0, upnpItf=65535) CMD: /bin/iptables -P INPUT ACCEPT CMD: /bin/iptables -P FORWARD ACCEPT CMD: /bin/iptables -A FORWARD -p tcp -o ppp+ --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu CMD: /bin/iptables -A FORWARD -p tcp -i ppp+ --tcp-flags SYN,RST SYN -m tcpmss --mss 1452:65495 -j TCPMSS --set-mss 1452 CMD: /bin/ip6tables -A FORWARD -p tcp -o ppp+ --tcp-flags SYN,RST SYN -j TCPMSS --clamp-mss-to-pmtu CMD: /bin/ip6tables -A FORWARD -p tcp -i ppp+ --tcp-flags SYN,RST SYN -m tcpmss --mss 1432:65475 -j TCPMSS --set-mss 1432 CMD: /bin/iptables -A INPUT -p udp --dport 520 -j ACCEPT CMD: /bin/iptables -A INPUT ! -i br+ -d 239.255.255.250 -j DROP Open file /var/run/dhcpcV6.leases.nas0_0 fail ! CMD: /bin/iptables -A INPUT -d 224.0.0.0/4 -j ACCEPT CMD: /bin/iptables -A INPUT -i lo -j ACCEPT CMD: /bin/ip6tables -A INPUT -i lo -j ACCEPT CMD: /bin/iptables -N aclblock CMD: /bin/iptables -t nat -N aclblock unlink /var/interface/uptime/nas0_0 CMD: /bin/iptables -t mangle -N aclblock CMD: /bin/iptables -F aclblock CMD: /bin/iptables -t nat -F aclblock CMD: /bin/iptables -t mangle -F aclblock CMD: /bin/iptables -I aclblock -i lo -j RETURN CMD: /bin/iptables -A aclblock ! -i br+ -m mark --mark 0x400000/0x400000 -j ACCEPT CMD: /bin/iptables -A aclblock -m state --state ESTABLISHED,RELATED -j ACCEPT CMD: /bin/iptables -A aclblock ! -i br+ -j DROP CMD: /bin/iptables -F aclblock CMD: /bin/iptables -t nat -F aclblock CMD: /bin/iptables -t mangle -F aclblock CMD: /bin/iptables -I aclblock -i lo -j RETURN CMD: /bin/iptables -A aclblock ! -i br+ -m mark --mark 0x400000/0x400000 -j ACCEPT CMD: /bin/iptables -A aclblock -i br+ -m iprange --src-range 192.168.0.0-192.168.0.255 -j RETURN CMD: /bin/iptables -A aclblock -p udp -i br+ --dport 53 -j RETURN CMD: /bin/iptables -A aclblock -p udp ! -i br+ --dport 53 -j DROP CMD: /bin/iptables -A aclblock -p udp -i br+ --dport 67 -j RETURN CMD: /bin/iptables -A aclblock -m state --state ESTABLISHED,RELATED -j ACCEPT CMD: /bin/iptables -A aclblock -j DROP CMD: /bin/iptables -A INPUT -j aclblock CMD: /bin/iptables -t nat -A PREROUTING -j aclblock CMD: /bin/iptables -t mangle -A PREROUTING -j aclblock CMD: /bin/ip6tables -N aclblock CMD: /bin/ip6tables -F aclblock CMD: /bin/ip6tables -P INPUT DROP CMD: /bin/ip6tables -A INPUT -j aclblock CMD: /bin/iptables -N cwmp_aclblock CMD: /bin/iptables -t mangle -N cwmp_aclblock CMD: /bin/ip6tables -t mangle -N cwmp_aclblock CMD: /bin/iptables -F cwmp_aclblock CMD: /bin/iptables -t mangle -F cwmp_aclblock CMD: /bin/iptables -A INPUT -j cwmp_aclblock CMD: /bin/iptables -t mangle -D PREROUTING -j cwmp_aclblock CMD: /bin/iptables -t mangle -A PREROUTING -j cwmp_aclblock CMD: /bin/ip6tables -t mangle -D PREROUTING -j cwmp_aclblock CMD: /bin/ip6tables -t mangle -A PREROUTING -j cwmp_aclblock CMD: /bin/ebtables -N br_lan_forward -P RETURN CMD: /bin/ebtables -A FORWARD -j br_lan_forward CMD: /bin/ebtables -D br_lan_forward -p IPv4 --ip-proto igmp -j BR_IGMP_MLD_DROP Sorry, rule does not exist. CMD: /bin/ebtables -D br_lan_forward -p IPv6 --ip6-proto ipv6-icmp --ip6-icmp-type 143:143/0:255 -j BR_IGMP_MLD_DROP Sorry, rule does not exist. CMD: /bin/ebtables -D br_lan_forward -p IPv6 --ip6-proto ipv6-icmp --ip6-icmp-type 130:132/0:255 -j BR_IGMP_MLD_DROP Sorry, rule does not exist. CMD: /bin/ebtables -F BR_IGMP_MLD_DROP CMD: /bin/ebtables -X BR_IGMP_MLD_DROP CMD: /bin/ebtables -N BR_IGMP_MLD_DROP CMD: /bin/ebtables -P BR_IGMP_MLD_DROP RETURN CMD: /bin/ebtables -A BR_IGMP_MLD_DROP -i eth+ -o eth+ -j DROP CMD: /bin/ebtables -A BR_IGMP_MLD_DROP -i eth+ -o wlan+ -j DROP CMD: /bin/ebtables -A BR_IGMP_MLD_DROP -i wlan+ -o eth+ -j DROP CMD: /bin/ebtables -A BR_IGMP_MLD_DROP -i wlan+ -o wlan+ -j DROP CMD: /bin/ebtables -A br_lan_forward -p IPv4 --ip-proto igmp -j BR_IGMP_MLD_DROP CMD: /bin/ebtables -A br_lan_forward -p IPv6 --ip6-proto ipv6-icmp --ip6-icmp-type 143:143/0:255 -j BR_IGMP_MLD_DROP CMD: /bin/ebtables -A br_lan_forward -p IPv6 --ip6-proto ipv6-icmp --ip6-icmp-type 130:132/0:255 -j BR_IGMP_MLD_DROP CMD: /bin/ebtables -N br_wan CMD: /bin/ebtables -P br_wan RETURN CMD: /bin/ebtables -N br_wan_out CMD: /bin/ebtables -P br_wan_out RETURN CMD: /bin/ebtables -N br_lan_out CMD: /bin/ebtables -P br_lan_out RETURN CMD: /bin/ebtables -A br_wan -i nas0_0 -j DROP CMD: /bin/ebtables -A br_wan_out -o nas0_0 -j DROP CMD: /bin/ebtables -A INPUT -j br_wan CMD: /bin/ebtables -A OUTPUT -j br_wan_out CMD: /bin/ebtables -A OUTPUT -j br_lan_out CMD: /bin/ebtables -N br_wan_forward CMD: /bin/ebtables -P br_wan_forward RETURN [block_br_wan_forward:3409] Entry.cmode =0, Entry.IpProtocol=3 CMD: /bin/ebtables -A br_wan_forward -i nas0_0 -o nas0+ -j DROP CMD: /bin/ebtables -A FORWARD -j br_wan_forward CMD: /bin/iptables -D INPUT -j voip_chain iptables v1.4.18: Couldn't load target `voip_chain':No such file or directory Try `iptables -h' or 'iptables --help' for more information. CMD: /bin/iptables -F voip_chain iptables: No chain/target/match by that name. CMD: /bin/iptables -X voip_chain iptables: No chain/target/match by that name. CMD: /bin/iptables -N voip_chain CMD: /bin/iptables -I INPUT -j voip_chain CMD: /bin/ebtables -N wlan_block -P RETURN CMD: /bin/ebtables -A FORWARD -j wlan_block CMD: /bin/ebtables -N br_pppoe CMD: /bin/ebtables -P br_pppoe RETURN CMD: /bin/ebtables -N br_pppoe_acl CMD: /bin/ebtables -P br_pppoe_acl DROP CMD: /bin/ebtables -A FORWARD -j br_pppoe CMD: /bin/ebtables -A br_pppoe_acl --proto 0x8100 --vlan-encap 0x8863 -j RETURN CMD: /bin/ebtables -A br_pppoe_acl --proto 0x8100 --vlan-encap 0x8864 -j RETURN CMD: /bin/ebtables -A br_pppoe_acl --proto 0x8863 -j RETURN CMD: /bin/ebtables -A br_pppoe_acl --proto 0x8864 -j RETURN CMD: /bin/ebtables -A br_pppoe_acl -p IPv4 -d 01:00:5e:00:00:00/ff:ff:ff:00:00:00 -j RETURN CMD: /bin/ebtables -A br_pppoe_acl -p IPv6 -d 33:33:00:00:00:00/ff:ff:00:00:00:00 -j RETURN CMD: /bin/iptables -N domainblk CMD: /bin/iptables -t mangle -N mark_for_domainBLK CMD: /bin/iptables -t mangle -I PREROUTING -j mark_for_domainBLK CMD: /bin/ip6tables -N domainblk CMD: /bin/iptables -A domainblk -p udp --dport 53 -m dns --qname example.com --rmatch -j DROP CMD: /bin/ip6tables -D domainblk -p udp --dport 53 -m dns --qname example.com --rmatch -j DROpf_rt_ActivateGpon 4193 deactivate GPON fail ret:-1 P ip6tables: B ad rule (does a matching rule exist in that chain?). omci_wrapper_activateGpon ioctl failed CMD: /bin/ip6tables -A domainblk -p udp --dport 53 -m dns --qname example.com --rmatch -j DROP CMD: /bin/iptables -A domainblk -p udp --dport 53 -m dns --qname wpad.domain.name --rmatch -j DROP CMD: /bin/ip6tables -D FORWARD -p udp --dport 53 -m dns --qname wpad.domain.name --rmatch -j DROP launch /bin/VoIP_maserati at 20 ip6tables: Bad rule (does a matching rule exist in that chain?). CMD: /bin/ip6tables -A FORWARD -p udp --dport 53 -m dns --qname wpad.domain.name --rmatch -j DROP CMD: /bin/iptables -A INPUT -j domainblk CMD: /bin/iptables -A FORWARD -j domainblk priority: 10, portmask 2047, rx: 807e1b88 priority: 1, portmask 2047, rx: 807e1ce8 insert here, priority: 4, portmask 32, rx: 8042d904 CMD: /bin/iptGPON_ESDRECOVER_VER=V1.0, state=0 ables -A OUTPUT -j domainblk [RTM_OMCI] Line change from O0 to O2 ! [RTM_OMCI] Line change from O2 to O3 ! CMD: /bin/ip6tables -A INPUT -j domainblk CMD: /bin/ip6tables -A FORWARD -j domainblk CMD: /bin/ip6tables -A OUTPUT -j domainblk CMD: /bin/iptables -N ntpblk CMD: /bin/iptables -A OUTPUT -j ntpblk CMD: /bin/iptables -N tr069 CMD: /bin/iptables -A INPUT -j tr069 CMD: /bin/ip6tables -N ipv6_tr069 CMD: /bin/ip6tables -A INPUT -j ipv6_tr069 voip flash client share size = 9424 waiting voip flash server init...) CMD: /bin/iptables -F tr069 CMD: /bin/ip6tables -F ipv6_tr069 CMD: /bin/iptables -t mangle -F interface_grouping_br0 iptables: No chain/target/match by that name. CMD: /bin/iptables -t mangle -D PREROUTING -i br0 -j interface_grouping_br0 iptables v1.4.18: Couldn't load target `interface_grouping_br0':No such file or directory Try `iptables -h' or 'iptables --help' for more information. CMD: /bin/iptables -t mangle -X interface_grouping_br0 Alarm handler returns fail: EthUni iptables: No chain/target/match by that name. CMD: /bin/iptables -N dhcp_port_filter CMD: /bin/iptables -A INPUT -j dhcp_port_filter CMD: /bin/iptables -t mangle -D PREROUTING -j dscp_remark_pre CMD: /bin/iptables -t mangle -F dscp_remark_pre CMD: /bin/iptables -t mangle -X dscp_remark_pre CMD: /bin/ip6tables -t mangle -D PREROUTING -j dscp_remark_pre CMD: /bin/ip6tables -t mangle -F dscp_remark_pre CMD: /bin/ip6tables -t mangle -X dscp_remark_pre CMD: /bin/iptables -t mangle -N dscp_remark_pre CMD: /bin/iptables -t mangle -A dscp_remark_pre -j CONNMARK2 --restore-mark2 --mask2 0x1fff800000 CMD: /bin/iptables -t mangle -A PREROUTING -j dscp_remark_pre CMD: /bin/ip6tables -t mangle -N dscp_remark_pre CMD: /bin/ip6tables -t mangle -A dscp_remark_pre -j CONNMARK2 --restore-mark2 --mask2 0x1fff800000 CMD: /bin/ip6tables -t mangle -A PREROUTING -j dscp_remark_pre CMD: /bin/iptables -t nat -N address_map_tbl iptables: Chain already exists. CMD: /bin/iptables -t nat -D POSTROUTING -j address_map_tbl iptables: No chain/target/match by that name. CMD: /bin/iptables -t nat -A POSTROUTING -j address_map_tbl CMD: /bin/ip6tables -t nat -N address_map_tbl ip6tables: Chain already exists. CMD: /bin/ip6tables -t nat -D POSTROUTING -j address_map_tbl ip6tables: No chain/target/match by that name. CMD: /bin/ip6tables -t nat -A POSTROUTING -j address_map_tbl CMD: /bin/iptables -t mangle -N voip_remarking CMD: /bin/iptables -t mangle -A POSTROUTING -p udp -j voip_remarking CMD: /bin/ip6tables -t mangle -N voip_remarking CMD: /bin/ip6tables -t mangle -A POSTROUTING -p udp -j voip_remarking CMD: /bin/iptables -N urlblock CMD: /bin/iptables -A FORWARD -i br+ -p tcp --tcp-flags SYN,FIN,RST NONE -m length ! --length 0:84 -j urlblock iptables: No chain/target/match by that name. CMD: /bin/ip6tables -N urlblock CMD: /bin/ip6tables -A FORWARD -i br+ -p tcp --tcp-flags SYN,FIN,RST NONE -m length ! --length 0:104 -j urlblock ip6tables: No chain/target/match by that name. CMD: /bin/iptables -t mangle -N urlblock_pre CMD: /bin/iptables -t mangle -A PREROUTING -i br+ -p tcp -j urlblock_pre CMD: /bin/iptables -t mangle -N urlblock_post CMD: /bin/iptables -t mangle -A POSTROUTING ! -o br+ -p tcp -j urlblock_post CMD: /bin/ip6tables -t mangle -N urlblock_pre CMD: /bin/ip6tables -t mangle -A PREROUTING -i br+ -p tcp -j urlblock_pre CMD: /bin/ip6tables -t mangle -N urlblock_post CMD: /bin/ip6tables -t mangle -A POSTROUTING ! -o br+ -p tcp -j urlblock_post CMD: /bin/iptables -F urlblock CMD: /bin/iptables -t mangle -F urlblock_post CMD: /bin/iptables -t mangle -F urlblock_pre CMD: /bin/ip6tables -F urlblock CMD: /bin/ip6tables -t mangle -F urlblock_post CMD: /bin/ip6tables -t mangle -F urlblock_pre CMD: /bin/sh -c /bin/ipset flush urlblk_port_filter ipset v7.5: The set with the given name does not exist CMD: /bin/sh -c /bin/ipset destroy urlblk_port_filter ipset v7.5: The set with the given name does not exist CMD: /bin/sh -c /bin/ipset create urlblk_port_filter bitmap:port range 1-65535 CMD: /bin/sh -c /bin/ipset flush urlblk_mac_filter ipset v7.5: The set with the given name does not exist CMD: /bin/sh -c /bin/ipset destroy urlblk_mac_filter ipset v7.5: The set with the given name does not exist CMD: /bin/sh -c /bin/ipset create urlblk_mac_filter hash:mac counters CMD: /bin/iptables -F urlblock_black iptables: No chain/target/match by that name. CMD: /bin/iptables -X urlblock_black iptables: No chain/target/match by that name. CMD: /bin/iptables -N urlblock_black CMD: /bin/iptables -F urlblock_white iptables: No chain/target/match by that name. CMD: /bin/iptables -X urlblock_white iptables: No chain/target/match by that name. CMD: /bin/iptables -N urlblock_white CMD: /bin/ip6tables -F urlblock_black ip6tables: No chain/target/match by that name. CMD: /bin/ip6tables -X urlblock_black ip6tables: No chain/target/match by that name. CMD: /bin/ip6tables -N urlblock_black CMD: /bin/ip6tables -F urlblock_white ip6tables: No chain/target/match by that name. CMD: /bin/ip6tables -X urlblock_white ip6tables: No chain/target/match by that name. CMD: /bin/ip6tables -N urlblock_white CMD: /bin/iptables -F URLBLK_ACT_REJECT_LOG iptables: No chain/target/match by that name. CMD: /bin/iptables -X URLBLK_ACT_REJECT_LOG iptables: No chain/target/match by that name. CMD: /bin/ip6tables -F URLBLK_ACT_REJECT_LOG ip6tables: No chain/target/match by that name. CMD: /bin/ip6tables -X URLBLK_ACT_REJECT_LOG ip6tables: No chain/target/match by that name. CMD: /bin/iptables -F URLBLK_ACT_REJECT iptables: No chain/target/match by that name. CMD: /bin/iptables -X URLBLK_ACT_REJECT iptables: No chain/target/match by that name. CMD: /bin/ip6tables -F URLBLK_ACT_REJECT ip6tables: No chain/target/match by that name. CMD: /bin/ip6tables -X URLBLK_ACT_REJECT ip6tables: No chain/target/match by that name. CMD: /bin/iptables -F URLBLK_ACT_ACCEPT_LOG iptables: No chain/target/match by that name. CMD: /bin/iptables -X URLBLK_ACT_ACCEPT_LOG iptables: No chain/target/match by that name. CMD: /bin/ip6tables -F URLBLK_ACT_ACCEPT_LOG ip6tables: No chain/target/match by that name. CMD: /bin/ip6tables -X URLBLK_ACT_ACCEPT_LOG ip6tables: No chain/target/match by that name. CMD: /bin/iptables -F URLBLK_ACT_ACCEPT iptables: No chain/target/match by that name. CMD: /bin/iptables -X URLBLK_ACT_ACCEPT iptables: No chain/target/match by that name. CMD: /bin/ip6tables -F URLBLK_ACT_ACCEPT ip6tables: No chain/target/match by that name. CMD: /bin/ip6tables -X URLBLK_ACT_ACCEPT ip6tables: No chain/target/match by that name. CMD: /bin/iptables -N portfw CMD: /bin/iptables -A FORWARD -j portfw CMD: /bin/iptables -t nat -N portfw CMD: /bin/iptables -t nat -A PREROUTING -j portfw CMD: /bin/iptables -t nat -N portfwPreNatLB CMD: /bin/iptables -t nat -A PREROUTING -j portfwPreNatLB CMD: /bin/iptables -t nat -N portfwPostNatLB CMD: /bin/iptables -t nat -A POSTROUTING -j portfwPostNatLB CMD: /bin/iptables -F portfw CMD: /bin/iptables -t nat -F portfw CMD: /bin/iptables -t nat -F portfwPreNatLB CMD: /bin/iptables -t nat -F portfwPostNatLB CMD: /bin/iptables -t nat -A portfw ! -i br0 -m mark --mark 0x400000/0x400000 -j RETURN CMD: /bin/iptables -N ipfilter CMD: /bin/iptables -A FORWARD -j ipfilter CMD: /bin/iptables -F ipfilter CMD: /bin/iptables -A ipfilter ! -i br+ ! -o br+ -j DROP CMD: /bin/iptables -A ipfilter -d 224.0.0.0/4 -j RETURN CMD: /bin/iptables -A ipfilter -m state --state ESTABLISHED,RELATED -j RETURN C MD: /bin/ethctl unknown cmd(21) conntrack killall CMD: /bin/iptables -N parental_ctrl CMD: /bin/iptables -A FORWARD -j parental_ctrl CMD: /bin/ip6tables -N parental_ctrl CMD: /bin/ip6tables -A FORWARD -j parental_ctrl CMD: /bin/iptables -t nat -N dmzPreNatLB CMD: /bin/iptables -t nat -A PREROUTING -j dmzPreNatLB CMD: /bin/iptables -t nat -N dmzPostNatLB CMD: /bin/iptables -t nat -A POSTROUTING -j dmzPostNatLB CMD: /bin/iptables -N dmz CMD: /bin/iptables -t nat -N dmz CMD: /bin/iptables -F dmz CMD: /bin/iptables -t nat -F dmz CMD: /bin/iptables -t nat -F dmzPreNatLB CMD: /bin/iptables -t nat -F dmzPostNatLB CMD: /bin/modprobe -r nf_nat_ftp CMD: /bin/iptables -A ipfilter -j dmz CMD: /bin/iptables -t nat -A PREROUTING -j dmz CMD: /bin/ebtables -N macfilter_forward CMD: /bin/ebtables -N macfilter_local_in CMD: /bin/ebtables -N macfilter_local_out CMD: /bin/ebtables -t nat -N macfilter_mc CMD: /bin/ebtables -t nat -P macfilter_mc RETURN CMD: /bin/ebtables -F macfilter_forward CMD: /bin/ebtables -F macfilter_local_in CMD: /bin/ebtables -F macfilter_local_out CMD: /bin/iptables -F macfilter_forward iptables: No chain/target/match by that name. CMD: /bin/ebtables -P macfilter_forward RETURN CMD: /bin/ebtables -P macfilter_local_in RETURN CMD: /bin/ebtables -P macfilter_local_out RETURN /bin/ebtables -P macfilter_forward RETURN CMD: /bin/echo 2 > /proc/fastbridge sh: can't create /proc/fastbridge: nonexistent directory CMD: /bin/sysconf send_unix_sock_message /var/run/systemd.usock do_flow_flush 8 CMD: /bin/ebtables -I INPUT -j macfilter_local_in CMD: /bin/ebtables -A OUTPUT -j macfilter_local_out CMD: /bin/ebtables -I FORWARD -j macfilter_forward CMD: /bin/ip6tables -P INPUT DROP CMD: /bin/ip6tables -A INPUT -p icmpv6 --icmpv6-type router-solicitation -j ACCEPT CMD: /bin/ip6tables -A INPUT -p icmpv6 --icmpv6-type router-advertisement -j ACCEPT CMD: /bin/ip6tables -A INPUT -p icmpv6 --icmpv6-type neighbour-solicitation -j ACCEPT CMD: /bin/ip6tables -A INPUT -p icmpv6 --icmpv6-type neighbour-advertisement -j ACCEPT CMD: /bin/ip6tables -A INPUT -p icmpv6 --icmpv6-type 130 -j ACCEPT CMD: /bin/ip6tables -A INPUT -p icmpv6 -i br+ -j ACCEPT CMD: /bin/ip6tables -A INPUT -i br+ -j ACCEPT CMD: /bin/ip6tables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT CMD: /bin/ip6tables -A INPUT -p udp --dport 546 -j ACCEPT CMD: /bin/ip6tables -A INPUT ! -i br0 -p udp --dport 547 -j ACCEPT CMD: /bin/ip6tables -N ipv6filter CMD: /bin/ip6tables -A FORWARD -j ipv6filter Restart IPv6 Filter! CMD: /bin/ip6tables -F ipv6filter CMD: /bin/ip6tables -A ipv6filter -m state --state ESTABLISHED,RELATED -j RETURN CMD: /bin/ip6tables -A ipv6filter ! -i br+ -j DROP voip_set_rg_1p_tag CMD: /bin/iptables -t mangle -F voip_remarking CMD: /bin/ip6tables -t mangle -F voip_remarking CMD: /bin/iptables -N vpnPassThrough CMD: /bin/iptables -A FORWARD -j vpnPassThrough CMD: /bin/ip6tables -N vpnPassThrough CMD: /bin/ip6tables -A FORWARD -j vpnPassThrough CMD: /bin/iptables -N tr247_multicast CMD: /bin/iptables -I OUTPUT -j tr247_multicast CMD: /bin/ebtables -N ISOLATION_MAP CMD: /bin/ebtables -P ISOLATION_MAP RETURN CMD: /bin/ebtables -I FORWARD -j ISOLATION_MAP CMD: /bin/ebtables -N ISOLATION_BRPORT CMD: /bin/ebtables -P ISOLATION_BRPORT DROP CMD: /bin/ebtables -A ISOLATION_BRPORT -i nas0+ -j RETURN CMD: /bin/ebtables -A ISOLATION_BRPORT -o nas0+ -j RETURN CMD: /bin/ebtables -A ISOLATION_BRPORT -d 1:80:c2:0:0:0/ff:ff:ff:0:0:0 -j RETURN CMD: /bin/ebtables -D ISOLATION_MAP --logical-out br0 -j ISOLATION_BRPORT Sorry, rule does not exist. CMD: /bin/ebtables -N L2_PPTP_PORT_SERVICE CMD: /bin/ebtables -P L2_PPTP_PORT_SERVICE RETURN CMD: /bin/ebtables -A L2_PPTP_PORT_SERVICE -p ipv4 --ip-proto udp --ip-dport 67:68 -j DROP CMD: /bin/ebtables -A L2_PPTP_PORT_SERVICE -p ipv4 --ip-proto 2 -j DROP CMD: /bin/ebtables -A L2_PPTP_PORT_SERVICE -p ipv6 --ip6-proto udp --ip6-dport 546:547 -j DROP CMD: /bin/ebtables -A L2_PPTP_PORT_SERVICE -p ipv6 --ip6-proto ipv6-icmp --ip6-icmp-type 130:134 -j DROP CMD: /bin/ebtables -N L2_PPTP_PORT_FORWARD CMD: /bin/ebtables -P L2_PPTP_PORT_FORWARD DROP CMD: /bin/ebtables -A L2_PPTP_PORT_FORWARD -d 01:80:C2:00:00:00/FF:FF:FF:00:00:00 -j RETURN CMD: /bin/ebtables -A L2_PPTP_PORT_FORWARD -i nas+ -j RETURN CMD: /bin/ebtables -N L2_PPTP_PORT_INPUT_TBL CMD: /bin/ebtables -P L2_PPTP_PORT_INPUT_TBL RETURN CMD: /bin/ebtables -I INPUT -j L2_PPTP_PORT_INPUT_TBL CMD: /bin/ebtables -N L2_PPTP_PORT_OUTPUT_TBL CMD: /bin/ebtables -P L2_PPTP_PORT_OUTPUT_TBL RETURN CMD: /bin/ebtables -I OUTPUT -j L2_PPTP_PORT_OUTPUT_TBL CMD: /bin/ebtables -N L2_PPTP_PORT_FORWARD_TBL CMD: /bin/ebtables -P L2_PPTP_PORT_FORWARD_TBL RETURN CMD: /bin/ebtables -I FORWARD -j L2_PPTP_PORT_FORWARD_TBL CMD: /bin/sysconf send_unix_sock_message /var/run/systemd.usock do_flow_flush 8 subr_qos_3.c: setupQosRuleMainChain 5523 CMD: /bin/ebtables -t broute -N qos_eb_us_rules CMD: /bin/ebtables -t broute -P qos_eb_us_rules RETURN CMD: /bin/ebtables -t broute -A BROUTING -j qos_eb_us_rules CMD: /bin/ebtables -t nat -N qos_eb_ds_rules CMD: /bin/ebtables -t nat -P qos_eb_ds_rules RETURN CMD: /bin/ebtables -t nat -A POSTROUTING -j qos_eb_ds_rules CMD: /bin/iptables -t mangle -N qos_ip_rules CMD: /bin/iptables -t mangle -A FORWARD -j qos_ip_rules CMD: /bin/iptables -t mangle -N pvc_mark CMD: /bin/iptables -t mangle -A FORWARD -j pvc_mark CMD: /bin/iptables -t mangle -N qos_rule_output CMD: /bin/iptables -t mangle -A OUTPUT -j qos_rule_output CMD: /bin/iptables -t mangle -N pvc_mark_output CMD: /bin/iptables -t mangle -A OUTPUT -j pvc_mark_output CMD: /bin/iptables -t mangle -N qos_iptable_action_us_rules CMD: /bin/iptables -t mangle -A POSTROUTING -j qos_iptable_action_us_rules CMD: /bin/ip6tables -t mangle -N qos_ip_rules CMD: /bin/ip6tables -t mangle -A FORWARD -j qos_ip_rules CMD: /bin/ip6tables -t mangle -N pvc_mark CMD: /bin/ip6tables -t mangle -A FORWARD -j pvc_mark CMD: /bin/ip6tables -t mangle -N qos_rule_output CMD: /bin/ip6tables -t mangle -A OUTPUT -j qos_rule_output CMD: /bin/ip6tables -t mangle -N pvc_mark_output CMD: /bin/ip6tables -t mangle -A OUTPUT -j pvc_mark_output CMD: /bin/ip6tables -t mangle -N qos_iptable_action_us_rules CMD: /bin/ip6tables -t mangle -A POSTROUTING -j qos_iptable_action_us_rules CMD: /bin/iptables -t mangle -D FORWARD -j dscp_remark CMD: /bin/iptables -t mangle -F dscp_remark CMD: /bin/iptables -t mangle -X dscp_remark CMD: /bin/iptables -t mangle -F dscp_remark_UP CMD: /bin/iptables -t mangle -X dscp_remark_UP CMD: /bin/iptables -t mangle -F dscp_remark_DOWN CMD: /bin/iptables -t mangle -X dscp_remark_DOWN CMD: /bin/ip6tables -t mangle -D FORWARD -j dscp_remark CMD: /bin/ip6tables -t mangle -F dscp_remark CMD: /bin/ip6tables -t mangle -X dscp_remark CMD: /bin/ip6tables -t mangle -F dscp_remark_UP CMD: /bin/ip6tables -t mangle -X dscp_remark_UP CMD: /bin/ip6tables -t mangle -F dscp_remark_DOWN CMD: /bin/ip6tables -t mangle -X dscp_remark_DOWN CMD: /bin/iptables -t mangle -N dscp_remark CMD: /bin/iptables -t mangle -N dscp_remark_UP CMD: /bin/iptables -t mangle -N dscp_remark_DOWN CMD: /bin/ip6tables -t mangle -N dscp_remark CMD: /bin/ip6tables -t mangle -N dscp_remark_UP CMD: /bin/ip6tables -t mangle -N dscp_remark_DOWN CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x0/0x1f800000 -j DSCP --set-dscp 0x0 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x0/0x1f800000 -j DSCP --set-dscp 0x0 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x800000/0x1f800000 -j DSCP --set-dscp 0x1 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x800000/0x1f800000 -j DSCP --set-dscp 0x1 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1000000/0x1f800000 -j DSCP --set-dscp 0x2 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1000000/0x1f800000 -j DSCP --set-dscp 0x2 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1800000/0x1f800000 -j DSCP --set-dscp 0x3 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1800000/0x1f800000 -j DSCP --set-dscp 0x3 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x2000000/0x1f800000 -j DSCP --set-dscp 0x4 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x2000000/0x1f800000 -j DSCP --set-dscp 0x4 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x2800000/0x1f800000 -j DSCP --set-dscp 0x5 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x2800000/0x1f800000 -j DSCP --set-dscp 0x5 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x3000000/0x1f800000 -j DSCP --set-dscp 0x6 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x3000000/0x1f800000 -j DSCP --set-dscp 0x6 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x3800000/0x1f800000 -j DSCP --set-dscp 0x7 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x3800000/0x1f800000 -j DSCP --set-dscp 0x7 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x4000000/0x1f800000 -j DSCP --set-dscp 0x8 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x4000000/0x1f800000 -j DSCP --set-dscp 0x8 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x4800000/0x1f800000 -j DSCP --set-dscp 0x9 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x4800000/0x1f800000 -j DSCP --set-dscp 0x9 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x5000000/0x1f800000 -j DSCP --set-dscp 0xa CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x5000000/0x1f800000 -j DSCP --set-dscp 0xa CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x5800000/0x1f800000 -j DSCP --set-dscp 0xb CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x5800000/0x1f800000 -j DSCP --set-dscp 0xb CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x6000000/0x1f800000 -j DSCP --set-dscp 0xc CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x6000000/0x1f800000 -j DSCP --set-dscp 0xc CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x6800000/0x1f800000 -j DSCP --set-dscp 0xd CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x6800000/0x1f800000 -j DSCP --set-dscp 0xd CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x7000000/0x1f800000 -j DSCP --set-dscp 0xe CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x7000000/0x1f800000 -j DSCP --set-dscp 0xe CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x7800000/0x1f800000 -j DSCP --set-dscp 0xf CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x7800000/0x1f800000 -j DSCP --set-dscp 0xf CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x8000000/0x1f800000 -j DSCP --set-dscp 0x10 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x8000000/0x1f800000 -j DSCP --set-dscp 0x10 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x8800000/0x1f800000 -j DSCP --set-dscp 0x11 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x8800000/0x1f800000 -j DSCP --set-dscp 0x11 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x9000000/0x1f800000 -j DSCP --set-dscp 0x12 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x9000000/0x1f800000 -j DSCP --set-dscp 0x12 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x9800000/0x1f800000 -j DSCP --set-dscp 0x13 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x9800000/0x1f800000 -j DSCP --set-dscp 0x13 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xa000000/0x1f800000 -j DSCP --set-dscp 0x14 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xa000000/0x1f800000 -j DSCP --set-dscp 0x14 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xa800000/0x1f800000 -j DSCP --set-dscp 0x15 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xa800000/0x1f800000 -j DSCP --set-dscp 0x15 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xb000000/0x1f800000 -j DSCP --set-dscp 0x16 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xb000000/0x1f800000 -j DSCP --set-dscp 0x16 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xb800000/0x1f800000 -j DSCP --set-dscp 0x17 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xb800000/0x1f800000 -j DSCP --set-dscp 0x17 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xc000000/0x1f800000 -j DSCP --set-dscp 0x18 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xc000000/0x1f800000 -j DSCP --set-dscp 0x18 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xc800000/0x1f800000 -j DSCP --set-dscp 0x19 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xc800000/0x1f800000 -j DSCP --set-dscp 0x19 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xd000000/0x1f800000 -j DSCP --set-dscp 0x1a CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xd000000/0x1f800000 -j DSCP --set-dscp 0x1a CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xd800000/0x1f800000 -j DSCP --set-dscp 0x1b CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xd800000/0x1f800000 -j DSCP --set-dscp 0x1b CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xe000000/0x1f800000 -j DSCP --set-dscp 0x1c CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xe000000/0x1f800000 -j DSCP --set-dscp 0x1c CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xe800000/0x1f800000 -j DSCP --set-dscp 0x1d CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xe800000/0x1f800000 -j DSCP --set-dscp 0x1d CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xf000000/0x1f800000 -j DSCP --set-dscp 0x1e CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xf000000/0x1f800000 -j DSCP --set-dscp 0x1e CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xf800000/0x1f800000 -j DSCP --set-dscp 0x1f CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0xf800000/0x1f800000 -j DSCP --set-dscp 0x1f CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x10000000/0x1f800000 -j DSCP --set-dscp 0x20 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x10000000/0x1f800000 -j DSCP --set-dscp 0x20 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x10800000/0x1f800000 -j DSCP --set-dscp 0x21 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x10800000/0x1f800000 -j DSCP --set-dscp 0x21 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x11000000/0x1f800000 -j DSCP --set-dscp 0x22 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x11000000/0x1f800000 -j DSCP --set-dscp 0x22 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x11800000/0x1f800000 -j DSCP --set-dscp 0x23 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x11800000/0x1f800000 -j DSCP --set-dscp 0x23 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x12000000/0x1f800000 -j DSCP --set-dscp 0x24 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x12000000/0x1f800000 -j DSCP --set-dscp 0x24 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x12800000/0x1f800000 -j DSCP --set-dscp 0x25 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x12800000/0x1f800000 -j DSCP --set-dscp 0x25 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x13000000/0x1f800000 -j DSCP --set-dscp 0x26 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x13000000/0x1f800000 -j DSCP --set-dscp 0x26 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x13800000/0x1f800000 -j DSCP --set-dscp 0x27 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x13800000/0x1f800000 -j DSCP --set-dscp 0x27 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x14000000/0x1f800000 -j DSCP --set-dscp 0x28 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x14000000/0x1f800000 -j DSCP --set-dscp 0x28 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x14800000/0x1f800000 -j DSCP --set-dscp 0x29 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x14800000/0x1f800000 -j DSCP --set-dscp 0x29 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x15000000/0x1f800000 -j DSCP --set-dscp 0x2a CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x15000000/0x1f800000 -j DSCP --set-dscp 0x2a CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x15800000/0x1f800000 -j DSCP --set-dscp 0x2b CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x15800000/0x1f800000 -j DSCP --set-dscp 0x2b CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x16000000/0x1f800000 -j DSCP --set-dscp 0x2c CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x16000000/0x1f800000 -j DSCP --set-dscp 0x2c CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x16800000/0x1f800000 -j DSCP --set-dscp 0x2d CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x16800000/0x1f800000 -j DSCP --set-dscp 0x2d CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x17000000/0x1f800000 -j DSCP --set-dscp 0x2e CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x17000000/0x1f800000 -j DSCP --set-dscp 0x2e CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x17800000/0x1f800000 -j DSCP --set-dscp 0x2f CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x17800000/0x1f800000 -j DSCP --set-dscp 0x2f CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x18000000/0x1f800000 -j DSCP --set-dscp 0x30 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x18000000/0x1f800000 -j DSCP --set-dscp 0x30 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x18800000/0x1f800000 -j DSCP --set-dscp 0x31 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x18800000/0x1f800000 -j DSCP --set-dscp 0x31 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x19000000/0x1f800000 -j DSCP --set-dscp 0x32 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x19000000/0x1f800000 -j DSCP --set-dscp 0x32 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x19800000/0x1f800000 -j DSCP --set-dscp 0x33 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x19800000/0x1f800000 -j DSCP --set-dscp 0x33 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1a000000/0x1f800000 -j DSCP --set-dscp 0x34 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1a000000/0x1f800000 -j DSCP --set-dscp 0x34 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1a800000/0x1f800000 -j DSCP --set-dscp 0x35 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1a800000/0x1f800000 -j DSCP --set-dscp 0x35 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1b000000/0x1f800000 -j DSCP --set-dscp 0x36 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1b000000/0x1f800000 -j DSCP --set-dscp 0x36 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1b800000/0x1f800000 -j DSCP --set-dscp 0x37 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1b800000/0x1f800000 -j DSCP --set-dscp 0x37 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1c000000/0x1f800000 -j DSCP --set-dscp 0x38 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1c000000/0x1f800000 -j DSCP --set-dscp 0x38 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1c800000/0x1f800000 -j DSCP --set-dscp 0x39 CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1c800000/0x1f800000 -j DSCP --set-dscp 0x39 CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1d000000/0x1f800000 -j DSCP --set-dscp 0x3a CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1d000000/0x1f800000 -j DSCP --set-dscp 0x3a CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1d800000/0x1f800000 -j DSCP --set-dscp 0x3b CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1d800000/0x1f800000 -j DSCP --set-dscp 0x3b CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1e000000/0x1f800000 -j DSCP --set-dscp 0x3c CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1e000000/0x1f800000 -j DSCP --set-dscp 0x3c CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1e800000/0x1f800000 -j DSCP --set-dscp 0x3d CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1e800000/0x1f800000 -j DSCP --set-dscp 0x3d CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1f000000/0x1f800000 -j DSCP --set-dscp 0x3e CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1f000000/0x1f800000 -j DSCP --set-dscp 0x3e CMD: /bin/iptables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1f800000/0x1f800000 -j DSCP --set-dscp 0x3f CMD: /bin/ip6tables -t mangle -A dscp_remark_UP -m mark2 --mark2 0x1f800000/0x1f800000 -j DSCP --set-dscp 0x3f CMD: /bin/iptables -t mangle -A dscp_remark ! -o br+ -m mark2 --mark2 0x20000000/0x20000000 -j dscp_remark_UP CMD: /bin/ip6tables -t mangle -A dscp_remark ! -o br+ -m mark2 --mark2 0x20000000/0x20000000 -j dscp_remark_UP CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x0/0xfc0000000 -j DSCP --set-dscp 0x0 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x0/0xfc0000000 -j DSCP --set-dscp 0x0 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x40000000/0xfc0000000 -j DSCP --set-dscp 0x1 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x40000000/0xfc0000000 -j DSCP --set-dscp 0x1 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x80000000/0xfc0000000 -j DSCP --set-dscp 0x2 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x80000000/0xfc0000000 -j DSCP --set-dscp 0x2 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xc0000000/0xfc0000000 -j DSCP --set-dscp 0x3 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xc0000000/0xfc0000000 -j DSCP --set-dscp 0x3 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x100000000/0xfc0000000 -j DSCP --set-dscp 0x4 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x100000000/0xfc0000000 -j DSCP --set-dscp 0x4 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x140000000/0xfc0000000 -j DSCP --set-dscp 0x5 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x140000000/0xfc0000000 -j DSCP --set-dscp 0x5 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x180000000/0xfc0000000 -j DSCP --set-dscp 0x6 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x180000000/0xfc0000000 -j DSCP --set-dscp 0x6 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x1c0000000/0xfc0000000 -j DSCP --set-dscp 0x7 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x1c0000000/0xfc0000000 -j DSCP --set-dscp 0x7 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x200000000/0xfc0000000 -j DSCP --set-dscp 0x8 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x200000000/0xfc0000000 -j DSCP --set-dscp 0x8 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x240000000/0xfc0000000 -j DSCP --set-dscp 0x9 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x240000000/0xfc0000000 -j DSCP --set-dscp 0x9 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x280000000/0xfc0000000 -j DSCP --set-dscp 0xa CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x280000000/0xfc0000000 -j DSCP --set-dscp 0xa CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x2c0000000/0xfc0000000 -j DSCP --set-dscp 0xb CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x2c0000000/0xfc0000000 -j DSCP --set-dscp 0xb CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x300000000/0xfc0000000 -j DSCP --set-dscp 0xc CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x300000000/0xfc0000000 -j DSCP --set-dscp 0xc CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x340000000/0xfc0000000 -j DSCP --set-dscp 0xd CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x340000000/0xfc0000000 -j DSCP --set-dscp 0xd CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x380000000/0xfc0000000 -j DSCP --set-dscp 0xe CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x380000000/0xfc0000000 -j DSCP --set-dscp 0xe CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x3c0000000/0xfc0000000 -j DSCP --set-dscp 0xf CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x3c0000000/0xfc0000000 -j DSCP --set-dscp 0xf CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x400000000/0xfc0000000 -j DSCP --set-dscp 0x10 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x400000000/0xfc0000000 -j DSCP --set-dscp 0x10 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x440000000/0xfc0000000 -j DSCP --set-dscp 0x11 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x440000000/0xfc0000000 -j DSCP --set-dscp 0x11 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x480000000/0xfc0000000 -j DSCP --set-dscp 0x12 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x480000000/0xfc0000000 -j DSCP --set-dscp 0x12 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x4c0000000/0xfc0000000 -j DSCP --set-dscp 0x13 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x4c0000000/0xfc0000000 -j DSCP --set-dscp 0x13 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x500000000/0xfc0000000 -j DSCP --set-dscp 0x14 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x500000000/0xfc0000000 -j DSCP --set-dscp 0x14 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x540000000/0xfc0000000 -j DSCP --set-dscp 0x15 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x540000000/0xfc0000000 -j DSCP --set-dscp 0x15 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x580000000/0xfc0000000 -j DSCP --set-dscp 0x16 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x580000000/0xfc0000000 -j DSCP --set-dscp 0x16 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x5c0000000/0xfc0000000 -j DSCP --set-dscp 0x17 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x5c0000000/0xfc0000000 -j DSCP --set-dscp 0x17 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x600000000/0xfc0000000 -j DSCP --set-dscp 0x18 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x600000000/0xfc0000000 -j DSCP --set-dscp 0x18 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x640000000/0xfc0000000 -j DSCP --set-dscp 0x19 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x640000000/0xfc0000000 -j DSCP --set-dscp 0x19 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x680000000/0xfc0000000 -j DSCP --set-dscp 0x1a CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x680000000/0xfc0000000 -j DSCP --set-dscp 0x1a CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x6c0000000/0xfc0000000 -j DSCP --set-dscp 0x1b CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x6c0000000/0xfc0000000 -j DSCP --set-dscp 0x1b CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x700000000/0xfc0000000 -j DSCP --set-dscp 0x1c CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x700000000/0xfc0000000 -j DSCP --set-dscp 0x1c CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x740000000/0xfc0000000 -j DSCP --set-dscp 0x1d CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x740000000/0xfc0000000 -j DSCP --set-dscp 0x1d CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x780000000/0xfc0000000 -j DSCP --set-dscp 0x1e CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x780000000/0xfc0000000 -j DSCP --set-dscp 0x1e CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x7c0000000/0xfc0000000 -j DSCP --set-dscp 0x1f CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x7c0000000/0xfc0000000 -j DSCP --set-dscp 0x1f CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x800000000/0xfc0000000 -j DSCP --set-dscp 0x20 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x800000000/0xfc0000000 -j DSCP --set-dscp 0x20 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x840000000/0xfc0000000 -j DSCP --set-dscp 0x21 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x840000000/0xfc0000000 -j DSCP --set-dscp 0x21 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x880000000/0xfc0000000 -j DSCP --set-dscp 0x22 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x880000000/0xfc0000000 -j DSCP --set-dscp 0x22 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x8c0000000/0xfc0000000 -j DSCP --set-dscp 0x23 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x8c0000000/0xfc0000000 -j DSCP --set-dscp 0x23 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x900000000/0xfc0000000 -j DSCP --set-dscp 0x24 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x900000000/0xfc0000000 -j DSCP --set-dscp 0x24 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x940000000/0xfc0000000 -j DSCP --set-dscp 0x25 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x940000000/0xfc0000000 -j DSCP --set-dscp 0x25 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x980000000/0xfc0000000 -j DSCP --set-dscp 0x26 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x980000000/0xfc0000000 -j DSCP --set-dscp 0x26 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x9c0000000/0xfc0000000 -j DSCP --set-dscp 0x27 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0x9c0000000/0xfc0000000 -j DSCP --set-dscp 0x27 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xa00000000/0xfc0000000 -j DSCP --set-dscp 0x28 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xa00000000/0xfc0000000 -j DSCP --set-dscp 0x28 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xa40000000/0xfc0000000 -j DSCP --set-dscp 0x29 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xa40000000/0xfc0000000 -j DSCP --set-dscp 0x29 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xa80000000/0xfc0000000 -j DSCP --set-dscp 0x2a CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xa80000000/0xfc0000000 -j DSCP --set-dscp 0x2a CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xac0000000/0xfc0000000 -j DSCP --set-dscp 0x2b CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xac0000000/0xfc0000000 -j DSCP --set-dscp 0x2b CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xb00000000/0xfc0000000 -j DSCP --set-dscp 0x2c CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xb00000000/0xfc0000000 -j DSCP --set-dscp 0x2c CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xb40000000/0xfc0000000 -j DSCP --set-dscp 0x2d CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xb40000000/0xfc0000000 -j DSCP --set-dscp 0x2d CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xb80000000/0xfc0000000 -j DSCP --set-dscp 0x2e CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xb80000000/0xfc0000000 -j DSCP --set-dscp 0x2e CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xbc0000000/0xfc0000000 -j DSCP --set-dscp 0x2f CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xbc0000000/0xfc0000000 -j DSCP --set-dscp 0x2f CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xc00000000/0xfc0000000 -j DSCP --set-dscp 0x30 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xc00000000/0xfc0000000 -j DSCP --set-dscp 0x30 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xc40000000/0xfc0000000 -j DSCP --set-dscp 0x31 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xc40000000/0xfc0000000 -j DSCP --set-dscp 0x31 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xc80000000/0xfc0000000 -j DSCP --set-dscp 0x32 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xc80000000/0xfc0000000 -j DSCP --set-dscp 0x32 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xcc0000000/0xfc0000000 -j DSCP --set-dscp 0x33 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xcc0000000/0xfc0000000 -j DSCP --set-dscp 0x33 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xd00000000/0xfc0000000 -j DSCP --set-dscp 0x34 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xd00000000/0xfc0000000 -j DSCP --set-dscp 0x34 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xd40000000/0xfc0000000 -j DSCP --set-dscp 0x35 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xd40000000/0xfc0000000 -j DSCP --set-dscp 0x35 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xd80000000/0xfc0000000 -j DSCP --set-dscp 0x36 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xd80000000/0xfc0000000 -j DSCP --set-dscp 0x36 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xdc0000000/0xfc0000000 -j DSCP --set-dscp 0x37 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xdc0000000/0xfc0000000 -j DSCP --set-dscp 0x37 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xe00000000/0xfc0000000 -j DSCP --set-dscp 0x38 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xe00000000/0xfc0000000 -j DSCP --set-dscp 0x38 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xe40000000/0xfc0000000 -j DSCP --set-dscp 0x39 CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xe40000000/0xfc0000000 -j DSCP --set-dscp 0x39 CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xe80000000/0xfc0000000 -j DSCP --set-dscp 0x3a CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xe80000000/0xfc0000000 -j DSCP --set-dscp 0x3a CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xec0000000/0xfc0000000 -j DSCP --set-dscp 0x3b CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xec0000000/0xfc0000000 -j DSCP --set-dscp 0x3b CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xf00000000/0xfc0000000 -j DSCP --set-dscp 0x3c CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xf00000000/0xfc0000000 -j DSCP --set-dscp 0x3c CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xf40000000/0xfc0000000 -j DSCP --set-dscp 0x3d CMD: /binnf_conntrack_h323: unknown parameter 'ports' ignored /ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xf40000000/0xfc0000000 -j DSCP --set-dscp 0x3d CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xf80000000/0xfc0000000 -j DSCP --set-dscp 0x3e CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xf80000000/0xfc0000000 -j DSCP --set-dscp 0x3e CMD: /bin/iptables -t mangle -A dscp_remark_DOWN -unknown cmd(21) m mark2 --mark2 0xfc0000000/0xfc0000000 -j DSCP --set-dscp 0x3f CMD: /bin/ip6tables -t mangle -A dscp_remark_DOWN -m mark2 --mark2 0xfc0000000/0xfc0000000 -j DSCP --set-dscp 0x3f CMD: /bin/iptables -t mangle -A dscp_remark -o br+ -m mark2 --mark2 0x1000000000/0x1000000000 -j dscp_remark_DOWN CMD: /bin/ip6tables -t mangle -A dscp_remark -o br+ -m mark2 --mark2 0x1000000000/0x1000000000 -j dscp_remark_DOWN CMD: /bin/iptables -t mangle -A dscp_remark -j CONNMARK2 --save-mark2 --mask2 0x1fff800000 CMD: /bin/ip6tables -t mangle -A dscp_remark -j CONNMARK2 --save-mark2 --mask2 0x1fff800000 CMD: /bin/iptables -t mangle -A FORWARD -j dscp_remark CMD: /bin/ip6tables -t mangle -A FORWARD -j dscp_remark [setTmpBlockBridgeFloodPktRule 2645]restore RA in bridge fowward! CMD: /bin/ebtables -D FORWARD -d Multicast -p IPV6 --ip6-protocol ipv6-icmp --ip6-icmp-type 134 -j DROP Sorry, rule does not exist. CMD: /bin/sh -c echo 1 > /sys/devices/virtual/net/br0/bridge/multicast_router CMD: /bin/iptables -F vpnPassThrough CMD: /bin/ip6tables -F vpnPassThrough setupAlgOnOff:4967 pptp_port ports=1723 CMD: /bin/modprobe nf_conntrack_pptp ports=1723 CMD: /bin/modprobe nf_nat_pptp setupAlgOnOff:4992 ftp_port ports=21 CMD: /bin/modprobe nf_conntrack_ftp ports=21 CMD: /bin/modprobe nf_nat_ftp setupAlgOnOff:5016 tftp_port ports=69 CMD: /bin/modprobe nf_conntrack_tftp ports=69 CMD: /bin/modprobe nf_nat_tftp setupAlgOnOff:5044 h323_port ports=1729,1720 CMD: /bin/modprobe nf_conntrack_h323 ports=1729,1720 CMD: /bin/modprobe nf_nat_h323 setupAlgOnOff:5122 sip_port ports=5060 CMD: /bin/modprobe nf_conntrack_sip ports=5060 CMD: /bin/modprobe nf_nat_sip CMD: /bin/ethctl conntrack killall CMD: /bin/sh -c /bin/smuxctl --if nas0 --rx --tags 1 --rule-remove-alias iptv_mvlan_nas0_0+ CMD: /bin/sh -c /bin/smuxctl --if nas0_0 --rx --tags 1 --rule-remove-alias iptv_mvlan_nas0_0+ CMD: /bin/sh -c /bin/smuxctl --if nas0 --rx --tags 2 --rule-remove-alias iptv_mvlan_nas0_0+ CMD: /bin/sh -c /bin/smuxctl --if nas0_0 --rx --tags 2 --rule-remove-alias iptv_mvlan_nas0_0+ CMD: /bin/sh -c echo 1 > /sys/class/net/br0/bridge/multicast_snooping CMD: /bin/sh -c echo 2 > sys/devices/virtual/net/br0/bridge/multicast_router CMD: /bin/sh -c echo 2 > /sys/devices/virtual/net/nas0_0/brport/multicast_router CMD: /bin/sh -c echo MRRK2_EXTPORT_EN 56 MRRK2_EXTPORTID_START 57 MRRK2_EXTPORTID_LEN 3 > proc/igmp/ctrl/skbMarkExtraSwitchPortId /bin/sh: can't create proc/igmp/ctrl/skbMarkExtraSwitchPortId: nonexistent directory [setTmpBlockBridgeFloodPktRule 2640]temporarily block RA in bridge fowward! CMD: /bin/ebtables -I FORWARD -d Multicast -p IPV6 --ip6-protocol ipv6-icmp --ip6-icmp-type 134 -j DROP CMD: /bin/ebtables -D INPUT -j portmapping_input Illegal target name 'portmapping_input'. CMD: /bin/ebtables -F portmapping_input Chain 'portmapping_input' doesn't exist. CMD: /bin/ebtables -X portmapping_input Chain 'portmapping_input' doesn't exist. CMD: /bin/ebtables -D OUTPUT -j portmapping_output Illegal target name 'portmapping_output'. CMD: /bin/ebtables -F portmapping_output Chain 'portmapping_output' doesn't exist. CMD: /bin/ebtables -X portmapping_output Chain 'portmapping_output' doesn't exist. CMD: /bin/ebtables -F portmapping_service Chain 'portmapping_service' doesn't exist. CMD: /bin/ebtables -X portmapping_service Chain 'portmapping_service' doesn't exist. CMD: /bin/ebtables -F portmapping_service2 Chain 'portmapping_service2' doesn't exist. CMD: /bin/ebtables -X portmapping_service2 Chain 'portmapping_service2' doesn't exist. CMD: /bin/ebtables -D FORWARD -j portmapping Illegal target name 'portmapping'. CMD: /bin/ebtables -F portmapping Chain 'portmapping' doesn't exist. CMD: /bin/ebtables -X portmapping Chain 'portmapping' doesn't exist. CMD: /bin/ebtables -t broute -D BROUTING -j portmapping_broute Illegal target name 'portmapping_broute'. CMD: /bin/ebtables -t broute -F portmapping_broute Chain 'portmapping_broute' doesn't exist. CMD: /bin/ebtables -t broute -X portmapping_broute Chain 'portmapping_broute' doesn't exist. CMD: /bin/iptables -t mangle -D PREROUTING -j portmapping_rt_tbl iptables v1.4.18: Couldn't load target `portmapping_rt_tbl':No such file or directory Try `iptables -h' or 'iptables --help' for more information. CMD: /bin/iptables -t mangle -F portmapping_rt_tbl iptables: No chain/target/match by that name. CMD: /bin/iptables -t mangle -X portmapping_rt_tbl iptables: No chain/target/match by that name. CMD: /bin/ip6tables -t mangle -D PREROUTING -j portmapping_rt_tbl ip6tables v1.4.18: Couldn't load target `portmapping_rt_tbl':No such file or directory Try `ip6tables -h' or 'ip6tables --help' for more information. CMD: /bin/ip6tables -t mangle -F portmapping_rt_tbl ip6tables: No chain/target/match by that name. CMD: /bin/ip6tables -t mangle -X portmapping_rt_tbl ip6tables: No chain/target/match by that name. CMD: /bin/ebtables -F ipv6_ra_local_out Chain 'ipv6_ra_local_out' doesn't exist. CMD: /bin/ebtables -D OUTPUT -j ipv6_ra_local_out Illegal target name 'ipv6_ra_local_out'. CMD: /bin/ebtables -X ipv6_ra_local_out Chain 'ipv6_ra_local_out' doesn't exist. CMD: /bin/ebtables -F portmapping_nas0_0_out Chain 'portmapping_nas0_0_out' doesn't exist. CMD: /bin/ebtables -t broute -D portmapping_broute -i eth0.2.0 -j mark --mark-or 0x102000 --mark-target CONTINUE Chain 'portmapping_broute' doesn't exist. CMD: /bin/ebtables -D portmapping_nas0_0_out -o eth0.2.0 -j RETURN Chain 'portmapping_nas0_0_out' doesn't exist. CMD: /bin/sh -c /bin/bridge vlan del vid 4001 dev eth0.2.0 CMD: /bin/sh -c /bin/bridge vlan add vid 1 dev eth0.2.0 untagged pvid master CMD: /bin/ebtables -D portmapping_input -i eth0.2.0 -j portmapping_service Chain 'portmapping_input' doesn't exist. CMD: /bin/ebtables -D portmapping_output -o eth0.2.0 -j portmapping_service Chain 'portmapping_output' doesn't exist. CMD: /bin/sh -c /bin/bridge vlan del vid 4001 dev nas0_0 CMD: /bin/sh -c /bin/bridge vlan add vid 1 dev nas0_0 untagged pvid master CMD: /bin/sh -c /bin/bridge vlan del vid 4001 dev br0 self [RTM_OMCI] Line change from O3 to O4 ! CMD: /bin/ebtables -D portmapping_input -i nas0_0 -j portmapping_service Chain 'portmapping_input' doesn't exist. CMD: /bin/ebtables -D portmapping_output -o nas0_0 -j portmapping_service Chain 'portmapping_output' doesn't exist. CMD: /bin/ebtables -D portmapping -o nas0_0 --mark ! 0x2000/0x7e000 -j DROP Chain 'portmapping' doesn't exist. CMD: /bin/ebtables -D portmapping --mark 0x2000/0x7e000 -j portmapping_nas0_0_out Chain 'portmapping' doesn't exist. CMD: /bin/ebtables -t broute -D portmapping_broute -i nas0_0 -j mark --mark-or 0x2000 --mark-target CONTINUE Chain 'portmapping_broute' doesn't exist. CMD: /bin/ebtables -D portmapping_output --mark 0x2000/0x7e000 -d Multicast -j portmapping_nas0_0_out Chain 'portmapping_output' doesn't exist. CMD: /bin/iptables -t mangle -D portmapping_rt_tbl -i nas0_0 -j MARK --set-mark 0x2000/0x7e000 iptables: Bad rule (does a matching rule exist in that chain?). CMD: /bin/ip6tables -t mangle -D portmapping_rt_tbl -i nas0_0 -j MARK --set-mark 0x2000/0x7e000 ip6tables: Bad rule (does a matching rule exist in that chain?). CMD: /bin/ebtables -F portmapping_nas0_0_out Chain 'portmapping_nas0_0_out' doesn't exist. CMD: /bin/ebtables -X portmapping_nas0_0_out Chain 'portmapping_nas0_0_out' doesn't exist. CMD: /bin/ebtables -N portmapping_input CMD: /bin/ebtables -P portmapping_input RETURN CMD: /bin/ebtables -A INPUT -j portmapping_input CMD: /bin/ebtables -N portmapping_output CMD: /bin/ebtables -P portmapping_output RETURN CMD: /bin/ebtables -A OUTPUT -j portmapping_output CMD: /bin/ebtables -N portmapping_service CMD: /bin/ebtables -P portmapping_service RETURN CMD: /bin/ebtables -A portmapping_service -p ipv4 --ip-proto udp --ip-dport 67:68 -j DROP CMD: /bin/ebtables -A portmapping_service -p ipv4 --ip-proto igmp -j DROP CMD: /bin/ebtables -A portmapping_service -p ipv4 --pkttype-type multicast -j DROP CMD: /bin/ebtables -A portmapping_service -p ipv6 --ip6-proto udp --ip6-dport 546:547 -j DROP CMD: /bin/ebtables -A portmapping_service -p ipv6 --ip6-proto ipv6-icmp --ip6-icmp-type 130:134 -j DROP CMD: /bin/ebtables -A portmapping_service -p ipv6 --ip6-proto ipv6-icmp --ip6-icmp-type 143 -j DROP CMD: /bin/ebtables -A portmapping_service -p ipv6 --ip6-proto ! ipv6-icmp --pkttype-type multicast -j DROP CMD: /bin/ebtables -N portmapping_service2 CMD: /bin/ebtables -P portmapping_service2 RETURN CMD: /bin/ebtables -A portmapping_service2 -p ipv4 --ip-proto udp --ip-dport 67:68 -j RETURN CMD: /bin/ebtables -A portmapping_service2 -p ipv4 --ip-proto igmp -j DROP CMD: /bin/ebtables -A portmapping_service2 -p ipv4 --pkttype-type multicast -j DROP CMD: /bin/ebtables -A portmapping_service2 -p ipv6 [RTM_OMCI] Line change from O4 to O5 ! --ip6-proto udp --ip6-dport 546:547 -j RETURN CMD: /bin/ebtables -A portmapping_service2 -p ipv6 --ip6-proto ipv6-icmp --ip6-icmp-type 130:134 -j RETURN CMD: /bin/ebtables -A portmapping_service2 -p ipv6 --ip6-proto ipv6-icmp --ip6-icmp-type 143 -j DROP CMD: /bin/ebtables -A portmapping_service2 -p ipv6 --ip6-proto ! ipv6-icmp --pkttype-type multicast -j DROP CMD: /bin/ebtables -N portmapping 4 cpu CMD: /bin/ebtables -P portmapping RETURN CMD: /bin/ebtables -A FORWARD -j portmapping CMD: /bin/ebtables -t broute -N portmapping_broute CMD: /bin/ebtables -t broute -P portmapping_broute RETURN CMD: /bin/sh -c /bin/ebtables -t broute -D portmapping_broute -j mark --mark-and 0xffe81fff Sorry, rule does not exist. CMD: /bin/sh -c /bin/ebtables -t broute -I portmapping_broute -j mark --mark-and 0xffe81fff CMD: /bin/ebtables -t broute -A BROUTING -j portmapping_broute CMD: /bin/iptables -t mangle -N portmapping_rt_tbl CMD: /bin/iptables -t mangle -A PREROUTING -j portmapping_rt_tbl CMD: /bin/ip6tables -t mangle -N portmapping_rt_tbl CMD: /bin/ip6tables -t mangle -A PREROUTING -j portmapping_rt_tbl CMD: /bin/ebtables -N ipv6_ra_local_out CMD: /bin/ebtables -P ipv6_ra_local_out RETURN CMD: /bin/ebtables -A OUTPUT -j ipv6_ra_local_out CMD: /bin/sh -c echo 1 > /sys/class/net/br0/bridge/vlan_filtering CMD: /bin/ebtables -F portmapping_nas0_0_out Chain 'portmapping_nas0_0_out' doesn't exist. CMD: /bin/ebtables -N portmapping_nas0_0_out CMD: /bin/ebtables -P portmapping_nas0_0_out DROP CMD: /bin/ebtables -t broute -A portmapping_broute -i eth0.2.0 -j mark --mark-or 0x102000 --mark-target CONTINUE CMD: /bin/ebtables -A portmapping_nas0_0_out -o eth0.2.0 -j RETURN CMD: /bin/sh -c /bin/bridge vlan add vid 4001 dev eth0.2.0 untagged pvid master CMD: /bin/sh -c /bin/bridge vlan add vid 1 dev eth0.2.0 untagged self RTNETLINK answers: Operation not supported CMD: /bin/ebtables -A portmapping_input -i eth0.2.0 -j portmapping_service CMD: /bin/ebtables -A portmapping_output -o eth0.2.0 -j portmapping_service CMD: /bin/sh -c /bin/bridge vlan add vid 4001 dev nas0_0 untagged pvid master CMD: /bin/sh -c /bin/bridge vlan del vid 1 dev nas0_0 CMD: /bin/sh -c /bin/bridge vlan add vid 4001 dev br0 untagged self CMD: /bin/ebtables -A portmapping_nas0_0_out -o nas0_0 -j RETURN CMD: /bin/ebtables -A portmapping_input -i nas0_0 -j portmapping_service CMD: /bin/ebtables -A portmapping_output -o nas0_0 -j portmapping_service CMD: /bin/ebtables -A portmapping -o nas0_0 --mark ! 0x2000/0x7e000 -j DROP CMD: /bin/ebtables -A portmapping --mark 0x2000/0x7e000 -j portmapping_nas0_0_out mib_info_id: get mib info id failed! (id=561) CMD: /bin/ebtables -A portmapping_output --mark 0x2000/0x7e000 -d Multicast -j portmapping_nas0_0_out CMD: /bin/ebtables -t broute -A portmapping_broute -i nas0_0 -j mark --mark-or 0x2000 --mark-target CONTINUE CMD: /bin/iptables -t mangle -A portmapping_rt_tbl -i nas0_0 -j MARK --set-mark 0x2000/0x7e000 CMD: /bin/ip6tables -t mangle -A portmapping_rt_tbl -i nas0_0 -j MARK --set-mark 0x2000/0x7e000 [setTmpBlockBridgeFloodPktRule 2645]restore RA in bridge fowward! CMD: /bin/ebtables -D FORWARD -d Multicast -p IPV6 --ip6-protocol ipv6-icmp --ip6-icmp-type 134 -j DROP CMD: /bin/sh -c /bin/iptables -t mangle -N VPN_POLICY_ROUTE CMD: /bin/sh -c /bin/iptables -t mangle -D PREROUTING -i br+ -j VPN_POLICY_ROUTE iptables: No chain/target/match by that name. CMD: /bin/sh -c /bin/iptables -t mangle -D OUTPUT -j VPN_POLICY_ROUTE iptables: No chain/target/match by that name. CMD: /bin/sh -c /bin/iptables -t mangle -A PREROUTING -i br+ -j VPN_POLICY_ROUTE CMD: /bin/sh -c /bin/iptables -t mangle -A OUTPUT -j VPN_POLICY_ROUTE rm: can't remove '/var/localtime': No such file or directory CMD: /bin/vsntp -s 0.openwrt.pool.ntp.org -s 1.openwrt.pool.ntp.org CMD: /bin/boa CMD: /bin/arp_monitor -F -d -t 3 -nf 3 -nt 7 -i br+ getaddrinfo: Temporary failure in name resolution connect 0.openwrt.pool.ntp.org: No such file or directory getaddrinfo: Temporary failure in name resolution connect 1.openwrt.pool.ntp.org: No such file or directory CMD: /bin/sh -c echo 1 > /sys/class/net/br0/bridge/multicast_snooping CMD: /bin/sh -c echo 2 > sys/devices/virtual/net/br0/bridge/multicast_router CMD: /bin/sh -c echo 2 > /sys/devices/virtual/neubi0 error: ubi_open_volume: cannot open device 0, volume 0, error -16 t/nas0_0/brport/multicast_router CMD: /bin/sh -c echo MRRK2_EXTPORT_EN 56 MRRK2_EXTPORTID_START 57 MRRK2_EXTPORTID_LEN 3 > proc/igmp/ctrl/skbMarkExtraSwitchPortId /bin/sh: can't create proc/igmp/ctrl/skbMarkExtraSwitchPortId: nonexistent directory [restart_ethernet@16821] eth0.2.0 is up getUniPortCapability:1120 line is 2;2;2;2 getUniPortCapability:1127 pch is 2, port is 0 [restart_ethernet@16821] eth0.3.0 is up getUniPortCapability:1120 line is 2;2;2;2 getUniPortCapability:1127 pch is 2, port is 1 [restart_ethernet@16821] eth0.4.0 is up getUniPortCapability:1120 line is 2;2;2;2 getUniPortCapability:1127 pch is 2, port is 2 [restart_ethernet@16821] eth0.5.0 is up getUniPortCapability:1120 line is 2;2;2;2 getUniPortCapability:1127 pch is 2 , port is 3 voip flash server share size = 9424 rcm_voip_get_ctype_interface ++++++The size of voipConfig 8724 voip omci line state share size = 1152 codec_suporrt_list 1279 [VOIP disable DEBUG] watch dog pipe mode <bind_web_socket:368> socket:4, ip_ver:6, port:443 VoIP RCM LOG is ENABLED!! Reset register status... CMD: /bin/iwpriv wlan0 flash_set xcap=66 wlan0 flash_set:xcap=66 CMD: /bin/iwpriv wlan0 flash_set thermalA=29 wlan0 flash_set:thermalA=29 CMD: /bin/iwpriv wlan0 flash_set thermalB=30 wlan0 flash_set:thermalB=30 CMD: /bin/iwpriv wlan0 flash_set thermalC=255 wlan0 flash_set:thermalC=255 CMD: /bin/iwpriv wlan0 flash_set thermalD=255 wlan0 flash_set:thermalD=255 CMD: /bin/iwpriv wlan0 flash_set 2G_cck_tssi_A=0f0f0b0b0f0f wlan0 flash_set:2G_cck_tssi_A=0f0f0b0b0f0f CMD: /bin/iwpriv wlan0 flash_set 2G_cck_tssi_B=16160d0d1010 wlan0 flash_set:2G_cck_tssi_B=16160d0d1010 CMD: /bin/iwpriv wlan0 flash_set 2G_cck_tssi_C=000000000000 wlan0 flash_set:2G_cck_tssi_C=000000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_cck_tssi_D=000000000000 wlan0 flash_set:2G_cck_tssi_D=000000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_bw40_1s_tssi_A=0c0c0b0f0f wlan0 flash_set:2G_bw40_1s_tssi_A=0c0c0b0f0f CMD: /bin/iwpriv wlan0 flash_set 2G_bw40_1s_tssi_B=13130e1111 wlan0 flash_set:2G_bw40_1s_tssi_B=13130e1111 CMD: /bin/iwpriv wlan0 flash_set 2G_bw40_1s_tssi_C=0000000000 wlan0 flash_set:2G_bw40_1s_tssi_C=0000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_bw40_1s_tssi_D=0000000000 wlan0 flash_set:2G_bw40_1s_tssi_D=0000000000 CMD: /bin/iwpriv wlan0 flash_set 5G_bw40_1s_tssi_A=f7f5f6f705040303fffefefcfafa wlan0 flash_set:5G_bw40_1s_tssi_A=f7f5f6f705040303fffefefcfafa CMD: /bin/iwpriv wlan0 flash_set 5G_bw40_1s_tssi_B=fbfafafa04050505020206040505 wlan0 flash_set:5G_bw40_1s_tssi_B=fbfafafa04050505020206040505 CMD: /bin/iwpriv wlan0 flash_set 5G_bw40_1s_tssi_C=0000000000000000000000000000 wlan0 flash_set:5G_bw40_1s_tssi_C=0000000000000000000000000000 CMD: /bin/iwpriv wlan0 flash_set 5G_bw40_1s_tssi_D=0000000000000000000000000000 wlan0 flash_set:5G_bw40_1s_tssi_D=0000000000000000000000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_CCK_GAIN_DIFF_A=000000000000 wlan0 flash_set:2G_CCK_GAIN_DIFF_A=000000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_CCK_GAIN_DIFF_B=000000000000 wlan0 flash_set:2G_CCK_GAIN_DIFF_B=000000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_CCK_GAIN_DIFF_C=000000000000 wlan0 flash_set:2G_CCK_GAIN_DIFF_C=000000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_CCK_GAIN_DIFF_D=000000000000 wlan0 flash_set:2G_CCK_GAIN_DIFF_D=000000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_GAIN_DIFF_A=0000000000 wlan0 flash_set:2G_GAIN_DIFF_A=0000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_GAIN_DIFF_B=0000000000 wlan0 flash_set:2G_GAIN_DIFF_B=0000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_GAIN_DIFF_C=0000000000 wlan0 flash_set:2G_GAIN_DIFF_C=0000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_GAIN_DIFF_D=0000000000 wlan0 flash_set:2G_GAIN_DIFF_D=0000000000 CMD: /bin/iwpriv wlan0 flash_set 5G_GAIN_DIFF_A=3f3f3f3f3f3f3f3f3f3f3f3f3f3f wlan0 flash_set:5G_GAIN_DIFF_A=3f3f3f3f3f3f3f3f3f3f3f3f3f3f CMD: /bin/iwpriv wlan0 flash_set 5G_GAIN_DIFF_B=4040404040404040404040404040 wlan0 flash_set:5G_GAIN_DIFF_B=4040404040404040404040404040 CMD: /bin/iwpriv wlan0 flash_set 5G_GAIN_DIFF_C=0000000000000000000000000000 wlan0 flash_set:5G_GAIN_DIFF_C=0000000000000000000000000000 CMD: /bin/iwpriv wlan0 flash_set 5G_GAIN_DIFF_D=0000000000000000000000000000 wlan0 flash_set:5G_GAIN_DIFF_D=0000000000000000000000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_CCK_CW_DIFF_A=000000000000 wlan0 flash_set:2G_CCK_CW_DIFF_A=000000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_CCK_CW_DIFF_B=000000000000 wlan0 flash_set:2G_CCK_CW_DIFF_B=000000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_CCK_CW_DIFF_C=000000000000 wlan0 flash_set:2G_CCK_CW_DIFF_C=000000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_CCK_CW_DIFF_D=000000000000 wlan0 flash_set:2G_CCK_CW_DIFF_D=000000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_CW_DIFF_A=0000000000 wlan0 flash_set:2G_CW_DIFF_A=0000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_CW_DIFF_B=0000000000 wlan0 flash_set:2G_CW_DIFF_B=0000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_CW_DIFF_C=0000000000 <bind_web_socket:368> socket:9, ip_ver:6, port:80 wlan0 flash_set:2G_CW_DIFF_C=0000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_CW_DIFF_D=0000000000 wlan0 flash_set:2G_CW_DIFF_D=0000000000 CMD: /bin/iwpriv wlan0 flash_set 5G_CW_DIFF_A=4242424242424242424242424242 wlan0 flash_set:5G_CW_DIFF_A=4242424242424242424242424242 CMD: /bin/iwpriv wlan0 flash_set 5G_CW_DIFF_B=3c3c3c3c3c3c3c3c3c3c3c3c3c3c wlan0 flash_set:5G_CW_DIFF_B=3c3c3c3c3c3c3c3c3c3c3c3c3c3c CMD: /bin/iwpriv wlan0 flash_set 5G_CW_DIFF_C=0000000000000000000000000000 wlan0 flash_set:5G_CW_DIFF_C=0000000000000000000000000000 CMD: /bin/iwpriv wlan0 flash_set 5G_CW_DIFF_D=0000000000000000000000000000 wlan0 flash_set:5G_CW_DIFF_D=0000000000000000000000000000 CMD: /bin/iwpriv wlan0 flash_set 2G_rx_gain_cck=1 wlan0 flash_set:2G_rx_gain_cck=1 CMD: /bin/iwpriv wlan0 flash_set 2G_rx_gain_ofdm=1 wlan0 flash_set:2G_rx_gain_ofdm=1 CMD: /bin/iwpriv wlan0 flash_set 5G_rx_gain_low=1 wlan0 flash_set:5G_rx_gain_low=1 CMD: /bin/iwpriv wlan0 flash_set 5G_rx_gain_mid=0 wlan0 flash_set:5G_rx_gain_mid=0 CMD: /bin/iwpriv wlan0 flash_set 5G_rx_gain_high=0 wlan0 flash_set:5G_rx_gain_high=0 CMD: /bin/iwpriv wlan0 flash_set para_path=/etc/conf/ wlan0 flash_set:para_path=/etc/conf/ CMD: /bin/sh -c echo 1 > /proc/net/rtk_wifi6/wlan0/coex_2g_40m /bin/sh: can't create /proc/net/rtk_wifi6/wlan0/coex_2g_40m: nonexistent directory CMD: /bin/iwpriv wlan1 flash_set xcap=63 wlan1 flash_set:xcap=63 CMD: /bin/iwpriv wlan1 flash_set thermalA=24 wlan1 flash_set:thermalA=24 CMD: /bin/iwpriv wlan1 flash_set thermalB=24 wlan1 flash_set:thermalB=24 CMD: /bin/iwpriv wlan1 flash_set thermalC=255 wlan1 flash_set:thermalC=255 CMD: /bin/iwpriv wlan1 flash_set thermalD=255 wlan1 flash_set:thermalD=255 CMD: /bin/iwpriv wlan1 flash_set 2G_cck_tssi_A=0f0f0b0b0f0f wlan1 flash_set:2G_cck_tssi_A=0f0f0b0b0f0f CMD: /bin/iwpriv wlan1 flash_set 2G_cck_tssi_B=16160d0d1010 wlan1 flash_set:2G_cck_tssi_B=16160d0d1010 CMD: /bin/iwpriv wlan1 flash_set 2G_cck_tssi_C=000000000000 wlan1 flash_set:2G_cck_tssi_C=000000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_cck_tssi_D=000000000000 wlan1 flash_set:2G_cck_tssi_D=000000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_bw40_1s_tssi_A=0c0c0b0f0f wlan1 flash_set:2G_bw40_1s_tssi_A=0c0c0b0f0f CMD: /bin/iwpriv wlan1 flash_set 2G_bw40_1s_tssi_B=13130e1111 wlan1 flash_set:2G_bw40_1s_tssi_B=13130e1111 CMD: /bin/iwpriv wlan1 flash_set 2G_bw40_1s_tssi_C=0000000000 wlan1 flash_set:2G_bw40_1s_tssi_C=0000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_bw40_1s_tssi_D=0000000000 wlan1 flash_set:2G_bw40_1s_tssi_D=0000000000 CMD: /bin/iwpriv wlan1 flash_set 5G_bw40_1s_tssi_A=f7f5f6f705040303fffefefcfafa wlan1 flash_set:5G_bw40_1s_tssi_A=f7f5f6f705040303fffefefcfafa CMD: /bin/iwpriv wlan1 flash_set 5G_bw40_1s_tssi_B=fbfafafa04050505020206040505 wlan1 flash_set:5G_bw40_1s_tssi_B=fbfafafa04050505020206040505 CMD: /bin/iwpriv wlan1 flash_set 5G_bw40_1s_tssi_C=0000000000000000000000000000 wlan1 flash_set:5G_bw40_1s_tssi_C=0000000000000000000000000000 CMD: /bin/iwpriv wlan1 flash_set 5G_bw40_1s_tssi_D=0000000000000000000000000000 wlan1 flash_set:5G_bw40_1s_tssi_D=0000000000000000000000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_CCK_GAIN_DIFF_A=000000000000 wlan1 flash_set:2G_CCK_GAIN_DIFF_A=000000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_CCK_GAIN_DIFF_B=000000000000 wlan1 flash_set:2G_CCK_GAIN_DIFF_B=000000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_CCK_GAIN_DIFF_C=000000000000 wlan1 flash_set:2G_CCK_GAIN_DIFF_C=000000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_CCK_GAIN_DIFF_D=000000000000 wlan1 flash_set:2G_CCK_GAIN_DIFF_D=000000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_GAIN_DIFF_A=0000000000 wlan1 flash_set:2G_GAIN_DIFF_A=0000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_GAIN_DIFF_B=0000000000 wlan1 flash_set:2G_GAIN_DIFF_B=0000000000 CMD: /bin/iwpriv wlan1dbg [rtw_mib_set][2251]multiap_ext_cmd=1 flash_set 2G_GAdbg [core_mib_multiap_ext_cmd][492]oper=1 value=0 IN_DIFF_C=000000dbg [core_mib_multiap_ext_cmd][495]set rtw_map_user_pid from 0 to 0 0000 wlan1 flash_set:2G_GAIN_DIFF_C=0000000000 CMD: /bin/iwpriv wlan1 dbg [rtw_mib_set][2251]multiap_ext_cmd=1 flash_set 2G_GAIdbg [core_mib_multiap_ext_cmd][492]oper=1 value=0 N_DIFF_D=0000000dbg [core_mib_multiap_ext_cmd][495]set rtw_map_user_pid from 0 to 0 000 wlan1 flash_set:2G_GAIN_DIFF_D=0000000000 CMD: /bin/iwpriv wlan1 flash_set 5G_GAIN_DIFF_A=3f3f3f3f3f3f3f3f3f3f3f3f3f3f wlan1 flash_set:5G_GAIN_DIFF_A=3f3f3f3f3f3f3f3f3f3f3f3f3f3f CMD: /bin/iwpriv wlan1 flash_set 5G_GAIN_DIFF_B=4040404040404040404040404040 wlan1 flash_set:5G_GAIN_DIFF_B=4040404040404040404040404040 CMD: /bin/iwpriv wlan1 flash_set 5G_GAIN_DIFF_C=0000000000000000000000000000 wlan1 flash_set:5G_GAIN_DIFF_C=0000000000000000000000000000 CMD: /bin/iwpriv wlan1 flash_set 5G_GAIN_DIFF_D=0000000000000000000000000000 wlan1 flash_set:5G_GAIN_DIFF_D=0000000000000000000000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_CCK_CW_DIFF_A=000000000000 wlan1 flash_set:2G_CCK_CW_DIFF_A=000000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_CCK_CW_DIFF_B=000000000000 wlan1 flash_set:2G_CCK_CW_DIFF_B=000000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_CCK_CW_DIFF_C=000000000000 wlan1 flash_set:2G_CCK_CW_DIFF_C=000000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_CCK_CW_DIFF_D=000000000000 wlan1 flash_set:2G_CCK_CW_DIFF_D=000000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_CW_DIFF_A=0000000000 wlan1 flash_set:2G_CW_DIFF_A=0000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_CW_DIFF_B=0000000000 wlan1 flash_set:2G_CW_DIFF_B=0000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_CW_DIFF_C=0000000000 wlan1 flash_set:2G_CW_DIFF_C=0000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_CW_DIFF_D=0000000000 wlan1 flash_set:2G_CW_DIFF_D=0000000000 CMD: /bin/iwpriv wlan1 flash_set 5G_CW_DIFF_A=4242424242424242424242424242 wlan1 flash_set:5G_CW_DIFF_A=4242424242424242424242424242 CMD: /bin/iwpriv wlan1 flash_set 5G_CW_DIFF_B=3c3c3c3c3c3c3c3c3c3c3c3c3c3c wlan1 flash_set:5G_CW_DIFF_B=3c3c3c3c3c3c3c3c3c3c3c3c3c3c CMD: /bin/iwpriv wlan1 flash_set 5G_CW_DIFF_C=0000000000000000000000000000 wlan1 flash_set:5G_CW_DIFF_C=0000000000000000000000000000 CMD: /bin/iwpriv wlan1 flash_set 5G_CW_DIFF_D=0000000000000000000000000000 wlan1 flash_set:5G_CW_DIFF_D=0000000000000000000000000000 CMD: /bin/iwpriv wlan1 flash_set 2G_rx_gain_cck=1 wlan1 flash_set:2G_rx_gain_cck=1 CMD: /bin/iwpriv wlan1 flash_set 2G_rx_gain_ofdm=1 wlan1 flash_set:2G_rx_gain_ofdm=1 CMD: /bin/iwpriv wlan1 flash_set 5G_rx_gain_low=1 wlan1 flash_set:5G_rx_gain_low=1 CMD: /bin/iwpriv wlan1 flash_set 5G_rx_gain_mid=0 wlan1 flash_set:5G_rx_gain_mid=0 CMD: /bin/iwpriv wlan1 flash_set 5G_rx_gain_high=0 wlan1 flash_set:5G_rx_gain_high=0 CMD: /bin/iwpriv wlan1 flash_set para_path=/etc/conf/ wlan1 flash_set:para_path=/etc/conf/ CMD: /bin/sh -c echo 1 > /proc/net/rtk_wifi6/wlan1/coex_2g_40m /bin/sh: can't create /proc/net/rtk_wifi6/wlan1/coex_2g_40m: nonexistent directory CMD: /bin/ebtables -F wlan_block Multi_AP_Service is starting, profile number is : 2 CMD: /bin/ebtables -N wlan_map_block -P RETURN CMD: /bin/ebtables -D FORWARD -j wlan_map_block Sorry, rule does not exist. CMD:Usage: /bin/ebtables -Enable unkown multicast data flooding: I FORWARD -j wlaecho 1 > proc/fc/ctrl/igmp_unkonwn_flood n_map_block Disable unkown multicast data flooding: CMD: /bin/ebtabecho 0 > proc/fc/ctrl/igmp_unkonwn_flood les -N map_portmstatus:disable apping -P RETURN CMD: /bin/ebtables -D FORWARD -j map_portmapping Sorry, rule does not exist. CMD: /bin/ebtables -A FORWARD -j map_portmapping CMD: /bin/ebtables -F wlan_map_block CMD: /bin/iptables -F tr069 CMD: /bin/ip6tables -F ipv6_tr069 sh: can't create /proc/br_igmpsnoop: nonexistent directory sh: can't create /proc/br_igmpquery: nonexistent directory sh: can't create /proc/br_mldsnoop: nonexistent directory sh: can't create /proc/br_mldquery: nonexistent directory CMD: /bin/sh -c echo 0 > /proc/fc/ctrl/igmp_unknown_flood IGMP Snooping: enabled MLD Snooping: enabled CMD: /bin/ebtables -D br_lan_forward -p IPv4 --ip-proto igmp -j BR_IGMP_MLD_DROP CMD: /bin/ebtables -D br_lan_forward -p IPv6 --ip6-proto ipv6-icmp --ip6-icmp-type 143:143/0:255 -j BR_IGMP_MLD_DROP CMD: /bin/ebtables -D br_lan_forward -p IPv6 --ip6-proto ipv6-icmp --ip6-icmp-type 130:132/0:255 -j BR_IGMP_MLD_DROP CMD: /bin/ebtables -F BR_IGMP_MLD_DROP CMD: /bin/ebtables -X BR_IGMP_MLD_DROP CMD: /bin/ebtables -N BR_IGMP_MLD_DROP CMD: /bin/ebtables -P BR_IGMP_MLD_DROP RETURN CMD: /bin/ebtables -A BR_IGMP_MLD_DROP -i eth+ -o eth+ -j DROP CMD: /bin/ebtables -A BR_IGMP_MLD_DROP -i eth+ -o wlan+ -j DROP CMD: /bin/ebtables -A BR_IGMP_MLD_DROP -i wlan+ -o eth+ -j DROP CMD: /bin/ebtables -A BR_IGMP_MLD_DROP -i wlan+ -o wlan+ -j DROP CMD: /bin/ebtables -A br_lan_forward -p IPv4 --ip-proto igmp -j BR_IGMP_MLD_DROP CMD: /bin/ebtables -A br_lan_forward -p IPv6 --ip6-proto ipv6-icmp --ip6-icmp-type 143:143/0:255 -j BR_IGMP_MLD_DROP CMD: /bin/ebtables -A br_lan_forward -p IPv6 --ip6-proto ipv6-icmp --ip6-icmp-type 130:132/0:255 -j BR_IGMP_MLD_DROP subr_qos_3.c: setupIPQ 6736 [setupLanItfMap:810] lan_itf_map.map[1].name:eth0.2.0 [setupLanItfMap:810] lan_itf_map.map[2].name:eth0.3.0 [setupLanItfMap:810] lan_itf_map.map[3].name:eth0.4.0 [setupLanItfMap:810] lan_itf_map.map[4].name:eth0.5.0 subr_qos_3.c: setupDefaultQdisc 6557 CMD: tc qdisc add dev nas0_0 root handle 1: prio [1;33;46m<subr_qos_3.c 6834 setupIPQ> [mConfig QoS total upstream 2097144 Kbps downstream 1024000 Kbps [1;33;46m<fc_api.c 4031 rtk_fc_total_upstream_bandwidth_set> [mbandwidth=2097144 mib_info_id: get mib info id failed! (id=555) CMD: /bin/iptables -t mangle -D POSTROUTING -p tcp --tcp-flags ALL ACK -m length --length 40:84 -m conntrack --ctstate ESTABLISHED -j TCP_SMALLACK_PROTECT iptables v1.4.18: Couldn't load target `TCP_SMALLACK_PROTECT':No such file or directory Try `iptables -h' or 'iptables --help' for more information. CMD: /bin/iptables -t mangle -F TCP_SMALLACK_PROTECT iptables: No chain/target/match by that name. CMD: /bin/iptables -t mangle -X TCP_SMALLACK_PROTECT iptables: No chain/target/match by that name. CMD: /bin/ip6tables -t mangle -D POSTROUTING -p tcp --tcp-flags ALL ACK -m length --length 60:104 -m conntrack --ctstate ESTABLISHED -j TCP_SMALLACK_PROTECT ip6tables v1.4.18: Couldn't load target `TCP_SMALLACK_PROTECT':No such file or directory Try `ip6tables -h' or 'ip6tables --help' for more information. CMD: /bin/ip6tables -t mangle -F TCP_SMALLACK_PROTECT ip6tables: No chain/target/match by that name. CMD: /bin/ip6tables -t mangle -X TCP_SMALLACK_PROTECT ip6tables: No chain/target/match by that name. CMD: /bin/sh -c echo 0x0 > /proc/fc/ctrl/flow_swFwded_aclTrapPri_mask CMD: /bin/sh -c echo mode kernel > /proc/fc/ctrl/flow_delay CMD: /bin/sh -c echo loop_eth_type=0xfffa count 10 > /proc/fc/ctrl/flow_delay mib_info_id: get mib info id failed! (id=556) CMD: /bin/sysconf send_unix_sock_message /var/run/systemd.usock do_flow_flush 8 CMD: /bin/smbd -s /var/smb.conf --option=netbios name=Realtek --option=server string=Realtek Samba Server -D echo "0 1 2 3" > /proc/sys/loopback_detect/lan_port_remapping CMD: /bin/smuxctl --if eth0.2 --rx --tags 1 --rule-remove-alias eth0.2-rx-loopdetect+ CMD: /bin/smuxctl --if eth0.3 --rx --tags 1 --rule-remove-alias eth0.3-rx-loopdetect+ CMD: /bin/smuxctl --if eth0.4 --rx --tags 1 --rule-remove-alias eth0.4-rx-loopdetect+ CMD: /bin/smuxctl --if eth0.5 --rx --tags 1 --rule-remove-alias eth0.5-rx-loopdetect+ echo 0xfffa > /proc/loopback_detect_ethtype CMD: /bin/loopback [stop_upnp:20437] Stop miniupnpd! (wanIf=ppp0) CMD: /bin/upnpctrl down ppp0 br0 loopback: LoopExistPeriod = 5 loopback: LoopCancelPeriod = 300 loopback: EthernetType = 0xFFenable loopback detect FA loopback: vid = untagged total 1 vlan values upnpctrl(down): MINIUPNPD did not start! CMD: /bin/sysconf send_unix_sock_message /var/run/systemd.usock do_LanV6Server restart do_restartLanV6Server - 611 do_cleanLanV6Server - 675 [setup_dhcpdv6_conf_with_single_br:806] mcast_rg_clear_all(), cmd=0 [RTM_OMCI] OMCI start to configure! enter pptp video Ani enter pptp video uni catv mib init!!!!!!!!!!!! Internet Systems Consortium DHCP Server 4.4.1 Copyright 2004-2018 Internet Systems Consortium. All rights reserved. For info, please visit https://www.isc.org/software/dhcp/ Config file: /var/dhcpd6.conf Database file: /var/dhcpd6.leases PID file: /var/run/dhcpd6.pid Wrote 0 NA, 0 TA, 0 PD leases to lease file. No subnet6 declaration for br0 (no IPv6 addresses). ** Ignoring requests on br0. If this is not what you want, please write a subnet6 declaration in your dhcpd.conf file for the network segment to which interface br0 is attached. ** Not configured to listen on any interfaces! If you think you have received this message due to a bug rather than a configuration issue please read the section on submitting bugs on either our web page at www.isc.org or in the README file before submitting a bug. These pages explain the proper process and the information we find helpful for debugging. exiting. [stop_upnp:20437] Stop miniupnpd! (wanIf=ppp0) upnpctrl(down): MINIUPNPD did not start! rtk_tr247_mcast_igmpproxy_config 1924: rtk_tr247_mcast_port_entry_find_by_port_id FAIL ! Reset register status... 4 cpu WLAN0 Dispatch mode: 1, cpu: 0 CMD: /bin/sh -c echo 1 > /proc/sys/net/ipv6/conf/br0/dad_transmits [resetUsbDevice]reset /sys/bus/usb/devices/usb1/authorized hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected usb usb1: authorized to connect [resetUsbDevice]reset /sys/bus/usb/devices/usb2/authorized hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usb usb2: authorized to connect [resetUsbDevice]reset /sys/bus/usb/devices/usb3/authorized hub 3-0:1.0: USB hub found hub 3-0:1.0: 1 port detected usb usb3: authorized to connect [resetUsbDevice]reset /sys/bus/usb/devices/usb4/authorized hub 4-0:1.0: USB hub found hub 4-0:1.0: 1 port detected usb usb4: authorized to connect [update_monitor_list_file:23737] process_name = systemd, action = 1 [update_monitor_list_file:23737] process_name = omci_app, action = 1 CMD: /bin/monitord System startup success ! ===== monitord ===== Debug message: off Monitor Timer: 15 sec. TP type is not supported in MacBridgePortPmhdDrvCfg: MacBriPortCfgData, 0x5 no hook mcast service no hook mcast service mcast_rg_prof_add(), cmd=3, profileId=1 mcast_rg_un_auth_join_bhvr_set(), cmd=20, profileId=1, unAuthJoinRqtBhvr=0 mcast_rg_last_mbr_query_intv_set(), cmd=19, profileId=1, lastMbrQueryIntval=10 mcast_rg_robustness_set(), cmd=15, profileId=1, robustness=0 no hook mcast service mcast_rg_query_intv_set(), cmd=17, profileId=1, queryIntval=125 mcast_rg_query_max_rsp_time_set(), cmd=18, profileId=1, queryMaxRspTime=100 no hook mcast service mcast_rg_us_igmp_tag_info_set(), cmd=21, profileId=1, tagCtrl=0, TCI=0x0000 mcast_rg_max_sim_group_set(),cmd=22, portId=0, maxGrpNum=0 mcast_rg_max_bw_set(), cmd=23, port =0, maxBw=0 mcast_rg_bw_enforce_set(), cmd=24, port =0, bwEnforceB=0 mcast_rg_mcast_profile_per_port_set() , cmd=1, profileId =1, portId=0 mcast_rg_igmp_function_set(), cmd=8, profileId=1, IGMPFun=0 mcast_rg_igmp_version_set() , cmd=7, profileId=1, version=2 mcast_rg_immediate_leave_set(), cmd=9, profileId=1, ImmediateLeave=0 mcast_rg_us_igmp_rate_set(), cmd=10, profileId=1, UsIGMPRate=0 mcast_rg_igmp_port_enable_set(), cmd=5, portId=0, SnoopingEnable=1 mcast_rg_igmp_port_enable_set(), cmd=5, portId=5, SnoopingEnable=1 mcast_rg_prof_add(), cmd=3, profileId=2 mcast_rg_un_auth_join_bhvr_set(), cmd=20, profileId=2, unAuthJoinRqtBhvr=0 mcast_rg_last_mbr_query_intv_set(), cmd=19, profileId=2, lastMbrQueryIntval=10 mcast_rg_robustness_set(), cmd=15, profileId=2, robustness=0 no hook mcast service mcast_rg_query_intv_set(), cmd=17, profileId=2, queryIntval=125 mcast_rg_query_max_rsp_time_set(), cmd=18, profileId=2, queryMaxRspTime=100 no hook mcast service mcast_rg_us_igmp_tag_info_set(), cmd=21, profileId=2, tagCtrl=0, TCI=0x0000 mcast_rg_max_sim_group_set(),cmd=22, portId=1, maxGrpNum=0 mcast_rg_max_bw_set(), cmd=23, port =1, maxBw=0 mcast_rg_bw_enforce_set(), cmd=24, port =1, bwEnforceB=0 mcast_rg_mcast_profile_per_port_set() , cmd=1, profileId =2, portId=1 mcast_rg_igmp_function_set(), cmd=8, profileId=2, IGMPFun=0 mcast_rg_igmp_version_set() , cmd=7, profileId=2, version=2 mcast_rg_immediate_leave_set(), cmd=9, profileId=2, ImmediateLeave=0 mcast_rg_us_igmp_rate_set(), cmd=10, profileId=2, UsIGMPRate=0 mcast_rg_igmp_port_enable_set(), cmd=5, portId=1, SnoopingEnable=1 mcast_rg_igmp_port_enable_set(), cmd=5, portId=5, SnoopingEnable=1 mcast_rg_prof_add(), cmd=3, profileId=3 mcast_rg_un_auth_join_bhvr_set(), cmd=20, profileId=3, unAuthJoinRqtBhvr=0 mcast_rg_last_mbr_query_intv_set(), cmd=19, profileId=3, lastMbrQueryIntval=10 mcast_rg_robustness_set(), cmd=15, profileId=3, robustness=0 no hook mcast service mcast_rg_query_intv_set(), cmd=17, profileId=3, queryIntval=125 mcast_rg_query_max_rsp_time_set(), cmd=18, profileId=3, queryMaxRspTime=100 no hook mcast service mcast_rg_us_igmp_tag_info_set(), cmd=21, profileId=3, tagCtrl=0, TCI=0x0000 mcast_rg_max_sim_group_set(),cmd=22, portId=2, maxGrpNum=0 mcast_rg_max_bw_set(), cmd=23, port =2, maxBw=0 mcast_rg_bw_enforce_set(), cmd=24, port =2, bwEnforceB=0 mcast_rg_mcast_profile_per_port_set() , cmd=1, profileId =3, portId=2 mcast_rg_igmp_function_set(), cmd=8, profileId=3, IGMPFun=0 mcast_rg_igmp_version_set() , cmd=7, profileId=3, version=2 mcast_rg_immediate_leave_set(), cmd=9, profileId=3, ImmediateLeave=0 mcast_rg_us_igmp_rate_set(), cmd=10, profileId=3, UsIGMPRate=0 mcast_rg_igmp_port_enable_set(), cmd=5, portId=2, SnoopingEnable=1 mcast_rg_igmp_port_enable_set(), cmd=5, portId=5, SnoopingEnable=1 mcast_rg_prof_add(), cmd=3, profileId=4 mcast_rg_un_auth_join_bhvr_set(), cmd=20, profileId=4, unAuthJoinRqtBhvr=0 mcast_rg_last_mbr_query_intv_set(), cmd=19, profileId=4, lastMbrQueryIntval=10 mcast_rg_robustness_set(), cmd=15, profileId=4, robustness=0 no hook mcast service mcast_rg_query_intv_set(), cmd=17, profileId=4, queryIntval=125 mcast_rg_query_max_rsp_time_set(), cmd=18, profileId=4, queryMaxRspTime=100 no hook mcast service mcast_rg_us_igmp_tag_info_set(), cmd=21, profileId=4, tagCtrl=0, TCI=0x0000 mcast_rg_max_sim_group_set(),cmd=22, portId=3, maxGrpNum=0 mcast_rg_max_bw_set(), cmd=23, port =3, maxBw=0 mcast_rg_bw_enforce_set(), cmd=24, port =3, bwEnforceB=0 mcast_rg_mcast_profile_per_port_set() , cmd=1, profileId =4, portId=3 mcast_rg_igmp_function_set(), cmd=8, profileId=4, IGMPFun=0 mcast_rg_igmp_version_set() , cmd=7, profileId=4, version=2 rtk_tr247_multicast_apply 3239: SUCESS ! mcast_rg_immediate_leave_set(), cmd=9, profileId=4, ImmediateLeave=0 mcast_rg_us_igmp_rate_set(), cmd=10, profileId=4, UsIGMPRate=0 mcast_rg_igmp_port_enable_set(), cmd=5, portId=3, SnoopingEnable=1 mcast_rg_igmp_port_enable_set(), cmd=5, portId=5, SnoopingEnable=1 mcast_rg_prof_add(), cmd=3, profileId=5 mcast_rg_un_auth_join_bhvr_set(), cmd=20, profileId=5, unAuthJoinRqtBhvr=0 mcast_rg_last_mbr_query_intv_set(), cmd=19, profileId=5, lastMbrQueryIntval=10 mcast_rg_robustness_set(), cmd=15, profileId=5, robustness=0 no hook mcast service mcast_rg_query_intv_set(), cmd=17, profileId=5, queryIntval=125 mcast_rg_query_max_rsp_time_set(), cmd=18, profileId=5, queryMaxRspTime=100 no hook mcast service mcast_rg_us_igmp_tag_info_set(), cmd=21, profileId=5, tagCtrl=0, TCI=0x0000 mcast_rg_max_sim_group_set(),cmd=22, portId=5, maxGrpNum=0 mcast_rg_max_bw_set(), cmd=23, port =5, maxBw=0 mcast_rg_bw_enforce_set(), cmd=24, port =5, bwEnforceB=0 mcast_rg_mcast_profile_per_port_set() , cmd=1, profileId =5, portId=5 mcast_rg_igmp_function_set(), cmd=8, profileId=5, IGMPFun=0 mcast_rg_igmp_version_set() , cmd=7, profileId=5, version=2 mcast_rg_immediate_leave_set(), cmd=9, profileId=5, ImmediateLeave=0 mcast_rg_us_igmp_rate_set(), cmd=10, profileId=5, UsIGMPRate=0 mcast_rg_igmp_port_enable_set(), cmd=5, portId=5, SnoopingEnable=1 rtk_tr247_multicast_new_port_create 3067: portId=0 existed(mibIndex=0) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_new_port_create 3067: portId=0 existed(mibIndex=0) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_new_port_create 3067: portId=0 existed(mibIndex=0) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! TP type is not supported in MacBridgePortPmhdDrvCfg: MacBriPortCfgData, 0x6 delete pq for tcont [0] fail TP type is not supported in MacBridgePortPmhdDrvCfg: MacBriPortCfgData, 0x7 delete pq for tcont [0] fail delete pq for tcont [0] fail TP type is not supported in MacBridgePortPmhdDrvCfg: MacBriPortCfgData, 0x8 delete pq for tcont [0] fail delete pq for tcont [0] fail delete pq for tcont [0] fail TP type is not supported in MacBridgePortPmhdDrvCfg: MacBriPortCfgData, 0x9 enter pptp video uni 4.omci set catv on !!!!!! set CATV_ENABLE=1 Test data to proceed: Anig pOmciMsg->content[0]: 7 Begin to get catv parameter catv_inoptpower,temp_date1_16bit=0x 0 temp_date1_16bit = 0.0 End to get catv parameter mib set tableIndex Anig rtk_tr247_multicast_new_port_create 3067: portId=0 existed(mibIndex=0) ! rtk_tr247_multicast_new_port_create 3067: portId=5 existed(mibIndex=1) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_apply 3239: SUCESS ! rtk_tr247_multicast_new_port_create 3067: portId=1 existed(mibIndex=2) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_new_port_create 3067: portId=1 existed(mibIndex=2) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_new_port_create 3067: portId=1 existed(mibIndex=2) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_new_port_create 3067: portId=1 existed(mibIndex=2) ! rtk_tr247_multicast_new_port_create 3067: portId=5 existed(mibIndex=1) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_apply 3239: SUCESS ! rtk_tr247_multicast_new_port_create 3067: portId=2 existed(mibIndex=3) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_new_port_create 3067: portId=2 existed(mibIndex=3) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_new_port_create 3067: portId=2 existed(mibIndex=3) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_new_port_create 3067: portId=2 existed(mibIndex=3) ! rtk_tr247_multicast_new_port_create 3067: portId=5 existed(mibIndex=1) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_apply 3239: SUCESS ! rtk_tr247_multicast_new_port_create 3067: portId=3 existed(mibIndex=4) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_new_port_create 3067: portId=3 existed(mibIndex=4) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_new_port_create 3067: portId=3 existed(mibIndex=4) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_new_port_create 3067: portId=3 existed(mibIndex=4) ! rtk_tr247_multicast_new_port_create 3067: portId=5 existed(mibIndex=1) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_fin0 d_by_profile_id FAIL (profileId=65535) ! [41;33m ===> Do flow flush <=== [0m rtk_tr247_multicast_apply 3239: SUCESS ! 0 rtk_tr247_multicast_new_port_create 3067: portId=5 existed(mibIndex=1) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_new_port_create 3067: portId=5 existed(mibIndex=1) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! rtk_tr247_multicast_new_port_create 3067: portId=5 existed(mibIndex=1) ! rtk_tr247_multicast_apply_port 2741: rtk_tr247_mcast_profile_entry_find_by_profile_id FAIL (profileId=65535) ! smuxctl failed(ret=-1) return errno(19) No such device smuxctl failed(ret=-1) return errno(19) No such device smuxctl failed(ret=-1) return errno(19) No such device cfg_mib_update_fn:4313 delay mib commit rtk_tr247_multicast_new_port_create 3067: portId=5 existed(mibIndex=1) ! [SMUX] nas0_0 carrier on !!! br0: port 5(nas0_0) entered forwarding state [RTM_OMCI] OMCI br0: port 5(nas0_0) entered forwarding state configuration is completed! IPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready 4 cpu [SMUX] nas0_0 carrier off !!! cmd:echo 37 > /var/interface/uptime/nas0_0 subr_qos_3.c: setupQosRuleChain 5643 [SMUX] nas0_0 carrier on !!! subr_qos_3.c: setupQdisc 6510 subr_qos_3.c: setup_prio_queue 5807 Cannot find device "imq0" unknown cmd(50) subr_qos_3.c: setupDefaultQdisc 6557 RTNETLINK answers: No such file or directory subr_qos_3.c: setupCarChain 2742 iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables v1.4.18: Couldn't load target `car_filter_us':No such file or directory Try `iptables -h' or 'iptables --help' for more information. iptables v1.4.18: Couldn't load target `car_filter_ds':No such file or directory Try `iptables -h' or 'iptables --help' for more information. iptables: No chain/target/match by that name. iptables v1.4.18: Couldn't load target `car_traffic_qos_us':No such file or directory Try `iptables -h' or 'iptables --help' for more information. iptables v1.4.18: Couldn't load target `car_traffic_qos_ds':No such file or directory Try `iptables -h' or 'iptables --help' for more information. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. iptables: Too many links. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. ip6tables: No chain/target/match by that name. ip6tables: No chain/target/match by that name. ip6tables: No chain/target/match by that name. ip6tables: No chain/target/match by that name. ip6tables v1.4.18: Couldn't load target `car_filter_us':No such file or directory Try `ip6tables -h' or 'ip6tables --help' for more information. ip6tables v1.4.18: Couldn't load target `cabr0: port 5(nas0_0) entered forwarding state r_filter_ds':No such file or directory Try `ip6tables -h' or 'ip6tables --help' for more information. ip6tables: No chain/target/match by that name. ip6tables v1.4.18: Couldn't load target `car_traffic_qos_us':No such file or directory Try `ip6tables -h' or 'ip6tables --help' for more information. ip6tables v1.4.18: Couldn't load target `car_traffic_qos_ds':No such file or directory Try `ip6tables -h' or 'ip6tables --help' for more information. ip6tables: No chain/target/match by that name. ip6tables: No chain/target/match by that name. ip6tables: Too many links. ip6tables: No chain/target/match by that name. ip6tables: No chain/target/match by that name. Chain 'car_traffic_qos_ebt' doesn't exist. Illegal target name 'car_traffic_qos_ebt'. Chain 'car_traffic_qos_ebt' doesn't exist. subr_qos_3.c: setupCarQdisc 2849 RTNETLINK answers: No such file or directory RTNETLINK answers: No such file or directory subr_qos_3.c: rtk_qos_smuxdev_qos_us_rule_flush 7934 subr_qos_3.c: setupIPQ 6736 [setupLanItfMap:810] lan_itf_map.map[1].name:eth0.2.0 [setupLanItfMap:810] lan_itf_map.map[2].name:eth0.3.0 [setupLanItfMap:810] lan_itf_map.map[3].name:eth0.4.0 [setupLanItfMap:810] lan_itf_map.map[4].name:eth0.5.0 subr_qos_3.c: setupDefaultQdisc 6557 [1;33;46m<subr_qos_3.c 6834 setupIPQ> [mConfig QoS total upstream 2097144 Kbps downstream 1024000 Kbps [1;33;46m<fc_api.c 4031 rtk_fc_total_upstream_bandwidth_set> [mbandwidth=2097144 mib_info_id: get mib info id failed! (id=555) iptables v1.4.18: Couldn't load target `TCP_SMALLACK_PROTECT':No such file or directory Try `iptables -h' or 'iptables --help' for more information. iptables: No chain/target/match by that name. iptables: No chain/target/match by that name. ip6tables v1.4.18: Couldn't load target `TCP_SMALLACK_PROTECT':No such file or directory Try `ip6tables -h' or 'ip6tables --help' for more information. ip6tables: No chain/target/match by that name. ip6tables: No chain/target/match by that name. mib_info_id: get mib info id failed! (id=556) 4 cpu RTNETLINK answers: File exists Open file /var/run/dhcpcV6.leases.nas0_0 fail ! [41;33m ===> Do flow flush <=== [0m 0 0 [rtk_pcie_host_shutdown] reset device using GPIO 40 [rtk_pcie_host_shutdown] reset device using GPIO 39 PCIE0 reset pin is set to GPIO 40 PCIE1 reset pin is set to GPIO 39 num = 0x[1], val = 0x[0]
OpenWrt bootlog
WIP: Only bootlog of initramfs at the moment
Bismarck Preloader 3.7 II: LPLR:11261 PLR:5cb134c9 BD:23062109 TK:msdk-4.8.5-mips-EB-3.18-u0.9.33-m32ut-170828_lunapro-171213 II: TLB initial done: .ro section works! .text and .ro sections work! II: cg_cpu_pll_init done II: cg_sram_pll_init done II: CPU0 1150MHz, CPU1 600MHz, DDR3 666MHz, LX 200MHz, SRAM 500MHz, SPIF 100MHz II: apro_otp_setup_fcn(fc) AK: ******* DRAM calibration version: v5.6 ******* AK: MEMPLL[31/63/95/127/159/191/223]=907f, c0000210, 64237c0, 320f0030, fff, a7f, 0 AK: TP=3, VD=1, CC=3, OT=2, EP=0, EB=0 ZQ: Clock: ODT/OCD=60/48, zq_zctrl_prog=0x c08033e, zq_zctrl_status=0x20a144 ZQ: Address: ODT/OCD=60/80, zq_zctrl_prog=0x1c080332, zq_zctrl_status=0x20a100 ZQ: DQ: ODT/OCD=60/60, zq_zctrl_prog=0x2c080338, zq_zctrl_status=0x20a122 ZQ: DQS: ODT/OCD=60/60, zq_zctrl_prog=0x3c080338, zq_zctrl_status=0x20a122 ZQ: INTERAL DDR3, ZQCL done, ZQCS Enable AK: MRS: mr[0]=0x101a50, mr[1]=0x110004, mr[2]=0x120010, mr[3]=0x130000 AK: Start DDR_Calibration AK: Bit/max_r_s/max_r_l/max_w_s/max_w_l Bit/max_r_s/max_r_l/max_w_s/max_w_l [ 0] 0 1f 0 1d [16] 0 1f 0 1f [ 1] 0 1f 0 1f [17] 0 1f 0 1f [ 2] 0 1f 0 1f [18] 0 1f 0 1f [ 3] 0 1f 0 1f [19] 0 1f 0 1f [ 4] 0 1f 0 1f [20] 0 1f 0 1f [ 5] 0 1f 0 1f [21] 0 1f 0 1f [ 6] 0 1f 0 1f [22] 0 1f 0 1f [ 7] 0 1f 0 1f [23] 0 1f 0 1f [ 8] 0 1f 0 1f [24] 0 1f 0 1f [ 9] 0 1f 0 1f [25] 0 1f 0 1f [10] 0 1f 0 1f [26] 0 1f 0 1f [11] 0 1f 0 1f [27] 0 1f 0 1f [12] 0 1f 0 1f [28] 0 1f 0 1f [13] 0 1f 0 1f [29] 0 1f 0 1f [14] 0 1f 0 1f [30] 0 1f 0 1f [15] 0 1f 0 1f [31] 0 1f 0 1f AK: Finish DDR_Calibration AK: DRAM size=0x10000000, tRFC[2]=0x165(nS), tREF=1729(nS) AK: DCR=0x21321003, DTR[0:2]=0x99655828, 0x909061f, 0x6f19000 II: Change Stack from 0x9f002edc to 0x806fffe0 II: U-boot Magic Number is 0x27051956 II: Inflating U-Boot (0x80700040 -> 0x83c00000)... OK II: Starting U-boot... U-Boot 2020.01 (Jun 21 2023 - 11:08:33 +0800) Board: RTL9607Cv2, MIPS interAptiv:1150MHz RLX5281:600MHz LX:200MHz DDR3:666MHz SCLK:100MHz ICACHE: 64KB (32-byte/4-way/512-set) DCACHE: 32KB (32-byte/4-way/256-set) DRAM: Physical 256 MiB, uboot useable size 256 MiB NAND: SPI NAND: 0xEFAA21, Mode(111/111) Create bbt: NAND: 128 MiB Loading Environment from NAND... OK In: serial Out: serial Err: serial II: Init Software Patch! II: sw_test II: Configurate otto_flash_layout Saving Environment to NAND... Erasing redundant NAND... Erasing at 0x100000 -- 100% complete. Writing to redundant NAND... OK OK NAND read: device 0 offset 0x0, size 0xe0000 917504 bytes read: OK CRC32 for 81c80000 ... 81d5ffff ==> 65d8241a Net: LUNA GMAC Warning: eth device name has a space! Hit any key to stop autoboot: 1 0 Phoebus# tftpboot ${freeAddrs} openwrt-realtek-rtl960x-bt-pon_bt-g711ax-initramfs-kernel.bin swcore_init Using LUNA GMAC device TFTP from server 192.168.1.7; our IP address is 192.168.1.3 Filename 'openwrt-realtek-rtl960x-bt-pon_bt-g711ax-initramfs-kernel.bin'. Load address: 0x83000000 Loading: *################################################################# ################################################################# ################################################################# ################################################################# ################################################################# ############################################ 852.5 KiB/s done Bytes transferred = 5409659 (528b7b hex) Phoebus# bootm ## Booting kernel from Legacy Image at 83000000 ... Image Name: MIPS OpenWrt Linux-6.18.2 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 5409595 Bytes = 5.2 MiB Load Address: 80100000 Entry Point: 80100000 Verifying Checksum ... OK Uncompressing Kernel Image [ 0.000000] Linux version 6.18.2 (binguy@binpc) (mips-openwrt-linux-musl-gcc (OpenWrt GCC 14.3.0 r32359+35-22a69dfa4a) 14.3.0, GNU ld (GNU Binutils) 2.44) #0 SMP Sun Dec 21 12:43:26 2025 [ 0.000000] SoC Type: Realtek RTL9607C subtype 18 rev B (6831) [ 0.000000] printk: legacy bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 0001a120 (MIPS interAptiv (multi)) [ 0.000000] MIPS: machine is BT-PON BT-G711AX [ 0.000000] earlycon: ns16550a0 at MMIO 0x18002000 (options '115200n8') [ 0.000000] printk: legacy bootconsole [ns16550a0] enabled [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Using appended Device Tree. [ 0.000000] OF: reserved mem: Reserved memory: No reserved-memory node in the DT [ 0.000000] VPE topology {2,2} total 4 [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] HighMem empty [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x000000000fffffff] [ 0.000000] percpu: Embedded 12 pages/cpu s18640 r8192 d22320 u49152 [ 0.000000] pcpu-alloc: s18640 r8192 d22320 u49152 alloc=12*4096 [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Kernel command line: earlycon [ 0.000000] printk: log buffer data + meta data: 131072 + 409600 = 540672 bytes [ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes, linear) [ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes, linear) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 65536 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=4, Nodes=1 [ 0.000000] rcu: Hierarchical RCU implementation. [ 0.000000] Tracing variant of Tasks RCU enabled. [ 0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies. [ 0.000000] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1 rcu_task_cpu_ids=4. [ 0.000000] NR_IRQS: 256 [ 0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention. [ 0.000000] Failed to get CPU clock: -2 [ 0.000000] CPU frequency from device tree: 1150MHz [ 0.000000] clocksource: GIC: mask: 0xffffffffffffffff max_cycles: 0x10939a911d9, max_idle_ns: 440795210078 ns [ 0.000003] sched_clock: 64 bits at 1150MHz, resolution 0ns, wraps every 2199023255551ns [ 0.009262] clocksource: realtek_otto_timer: mask: 0xfffffff max_cycles: 0xfffffff, max_idle_ns: 38225208801 ns [ 0.020677] Calibrating delay loop... 761.03 BogoMIPS (lpj=3805184) [ 0.067552] pid_max: default: 32768 minimum: 301 [ 0.080877] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.089046] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.112018] rcu: Hierarchical SRCU implementation. [ 0.117387] rcu: Max phase no-delay instances is 1000. [ 0.124778] smp: Bringing up secondary CPUs ... [ 0.131119] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.131159] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.131170] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.131249] CPU1 revision is: 0001a120 (MIPS interAptiv (multi)) [ 0.171370] Counter synchronization [CPU#0 -> CPU#1]: passed [ 0.209488] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.209527] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.209538] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.209585] CPU2 revision is: 0001a120 (MIPS interAptiv (multi)) [ 0.258492] Counter synchronization [CPU#0 -> CPU#2]: passed [ 0.295732] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.295767] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.295778] MIPS secondary cache 256kB, 8-way, linesize 32 bytes. [ 0.295833] CPU3 revision is: 0001a120 (MIPS interAptiv (multi)) [ 0.335961] Counter synchronization [CPU#0 -> CPU#3]: passed [ 0.371882] smp: Brought up 1 node, 4 CPUs [ 0.378299] Memory: 235688K/262144K available (8379K kernel code, 647K rwdata, 1720K rodata, 11324K init, 244K bss, 25080K reserved, 0K cma-reserved, 0K highmem) [ 0.397523] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.408828] posixtimers hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 0.417304] futex hash table entries: 1024 (32768 bytes on 1 NUMA nodes, total 32 KiB, linear). [ 0.432019] pinctrl core: initialized pinctrl subsystem [ 0.440419] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.447655] thermal_sys: Registered thermal governor 'step_wise' [ 0.447963] FPU Affinity set after 15220 emulations [ 0.472771] clocksource: Switched to clocksource realtek_otto_timer [ 0.487956] NET: Registered PF_INET protocol family [ 0.493714] IP idents hash table entries: 4096 (order: 3, 32768 bytes, linear) [ 0.502845] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.512211] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 0.520887] TCP established hash table entries: 2048 (order: 1, 8192 bytes, linear) [ 0.529495] TCP bind hash table entries: 2048 (order: 3, 32768 bytes, linear) [ 0.537625] TCP: Hash tables configured (established 2048 bind 2048) [ 0.545702] MPTCP token hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.554181] UDP hash table entries: 256 (order: 2, 14336 bytes, linear) [ 0.561645] UDP-Lite hash table entries: 256 (order: 2, 14336 bytes, linear) [ 0.570525] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 0.578918] workingset: timestamp_bits=14 max_order=16 bucket_order=2 [ 0.589200] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.595925] jffs2: version 2.2 (NAND) (SUMMARY) (ZLIB) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.628411] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.637437] printk: legacy console [ttyS0] disabled [ 0.644512] 18002000.uart: ttyS0 at MMIO 0x18002000 (irq = 22, base_baud = 12500000) is a 16550A [ 0.654577] printk: legacy console [ttyS0] enabled [ 0.654577] printk: legacy console [ttyS0] enabled [ 0.665337] printk: legacy bootconsole [early0] disabled [ 0.665337] printk: legacy bootconsole [early0] disabled [ 0.677542] printk: legacy bootconsole [ns16550a0] disabled [ 0.677542] printk: legacy bootconsole [ns16550a0] disabled [ 0.723105] brd: module loaded [ 0.730790] spi-nand spi0.0: Winbond SPI NAND was found. [ 0.737101] spi-nand spi0.0: 128 MiB, block size: 128 KiB, page size: 2048, OOB size: 64 [ 0.747020] 5 fixed-partitions partitions found on MTD device spi0.0 [ 0.754368] Creating 5 MTD partitions on "spi0.0": [ 0.759784] 0x000000000000-0x0000000e0000 : "u-boot" [ 0.769420] 0x0000000e0000-0x000000100000 : "u-boot-env" [ 0.777601] 0x000000100000-0x000000120000 : "u-boot-env2" [ 0.787445] 0x000000120000-0x000000140000 : "static_conf" [ 0.798392] 0x000000140000-0x000007d80000 : "ubi" [ 0.911730] i2c_dev: i2c /dev entries driver [ 0.926762] NET: Registered PF_INET6 protocol family [ 0.935661] Segment Routing with IPv6 [ 0.939840] In-situ OAM (IOAM) with IPv6 [ 0.944459] NET: Registered PF_PACKET protocol family [ 0.950179] 8021q: 802.1Q VLAN Support v1.8 [ 0.989912] UBI: auto-attach mtd4 [ 0.993765] ubi0: attaching mtd4 [ 1.702836] random: crng init done [ 1.933224] ubi0: scanning is finished [ 2.034770] ubi0: attached mtd4 (name "ubi", size 124 MiB) [ 2.041033] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes [ 2.048793] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 [ 2.056410] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096 [ 2.064194] ubi0: good PEBs: 994, bad PEBs: 0, corrupted PEBs: 0 [ 2.070888] ubi0: user volume: 5, internal volumes: 1, max. volumes count: 128 [ 2.078951] ubi0: max/mean erase counter: 5/2, WL threshold: 4096, image sequence number: 163500012 [ 2.089052] ubi0: available PEBs: 303, total reserved PEBs: 691, PEBs reserved for bad PEB handling: 20 [ 2.099598] ubi0: background thread "ubi_bgt0d" started, PID 355 [ 2.099750] clk: Disabling unused clocks [ 2.163099] Freeing unused kernel image (initmem) memory: 11324K [ 2.169830] This architecture does not have kernel memory protection. [ 2.177046] Run /init as init process [ 2.181125] with arguments: [ 2.184436] /init [ 2.186960] with environment: [ 2.190444] HOME=/ [ 2.193078] TERM=linux [ 2.588355] init: Console is alive [ 2.592561] init: - watchdog - [ 2.607933] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 2.616595] gpio_button_hotplug: loading out-of-tree module taints kernel. [ 2.626094] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 2.638663] init: - preinit - ls: /sys/class/net/lan*: No such file or directory BusyBox v1.37.0 (2025-12-21 12:43:26 UTC) multi-call binary. Usage: basename FILE [SUFFIX] | -a FILE... | -s SUFFIX FILE... Strip directory path and SUFFIX from FILE -a All arguments are FILEs -s SUFFIX Remove SUFFIX (implies -a) [ 2.981381] mtdblock: MTD device 'u-boot-env2' is NAND, please consider using UBI block devices instead. [ 3.146226] mtdblock: MTD device 'u-boot-env2' is NAND, please consider using UBI block devices instead. [ 3.311961] mtdblock: MTD device 'u-boot-env' is NAND, please consider using UBI block devices instead. Cannot parse config file '/etc/fw_env.config': No such file or directory Failed to find NVMEM device Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 7.823065] procd: - early - [ 7.826630] procd: - watchdog - [ 8.410796] procd: - watchdog - [ 8.414758] procd: - ubus - [ 8.473005] procd: - init - Please press Enter to activate this console. [ 8.891783] kmodloader: loading kernel modules from /etc/modules.d/* [ 8.963232] kmodloader: done loading kernel modules from /etc/modules.d/* [ 9.684542] urngd: v1.0.2 started. [ 10.369823] mtdblock: MTD device 'u-boot-env2' is NAND, please consider using UBI block devices instead. [ 10.533729] mtdblock: MTD device 'u-boot-env2' is NAND, please consider using UBI block devices instead. [ 10.699603] mtdblock: MTD device 'u-boot-env' is NAND, please consider using UBI block devices instead. BusyBox v1.37.0 (2025-12-21 12:43:26 UTC) built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r32359+35-22a69dfa4a ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- OpenWrt recently switched to the "apk" package manager! OPKG Command APK Equivalent Description ------------------------------------------------------------------ opkg install <pkg> apk add <pkg> Install a package opkg remove <pkg> apk del <pkg> Remove a package opkg upgrade apk upgrade Upgrade all packages opkg files <pkg> apk info -L <pkg> List package contents opkg list-installed apk info List installed packages opkg update apk update Update package lists opkg search <pkg> apk search <pkg> Search for packages ------------------------------------------------------------------ For more information visit: https://openwrt.org/docs/guide-user/additional-software/opkg-to-apk-cheatsheet root@OpenWrt:~#





