Edimax BR-6208AC V2

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

DualBand AC WLAN Router.

Generic Router

Openwrt can be either installed by uploading the sysupgrade image via the default web interface. Or it can be installed through uboot with by providing the image from a tftp server and attach a serial console to tell uboot to do so.

CPU Ram Flash Network WLAN USB Serial JTag
MT7620A @ 580 MHz 64 MiB 16 MiB 4x 10/100 bgn No Yes ?
Architecture MIPS
Vendor Ralink
Bootloader U-Boot
System-On-Chip MediaTec MT7620A
CPU/Speed 580 MHz
Flash-Chip unknown
Flash size 16 MiB
RAM 64 MiB
Wireless MT7620 2.4GHz 802.11bgn
Ethernet 10/100 Mbit/s w/ vlan support
Switch MT7620A
USB
Serial Yes
JTAG Not populated

Insert photo of front of the casing

Insert photo of back of the casing

Insert photo of backside label

Insert photo of PCB

Remove the 4 screws and then pull the cover apart.

port.serial general information about the serial port, serial port cable, etc.

The PCB design is nice: all the serial pins are labeled. Only a header has to be soldered in place.

Serial connection parameters
for Edimax BR-6208AC V2
57600, 8N1, 3.3V

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

U-Boot 1.1.3 (Aug 2 2016 - 13:38:35) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fb4000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. ************** Init GPIO Pin Start ************** RALINK_GPIOMODE_UARTF=0x00009801 ************** Init GPIO Pin Done ************** spi_wait_nsec: 29 spi device id: ef 40 18 0 0 (40180000) find flash: W25Q128BV raspi_read: from:30000 len:1000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.1.2.0 -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Aug 2 2016 Time:13:38:35 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 5: Load ucos code to SDRAM via TFTP Client. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Booting image at bc070000 ... raspi_read: from:70000 len:40 Magic number at 0xBC070000 raspi_read: from:70014 len:40 Image Name: Linux Kernel Image Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 6270892 Bytes = 6 MB Load Address: 80000000 Entry Point: 8000c2f0 raspi_read: from:70054 len:5fafac Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 8000c2f0) ... ## Giving linux memsize in MB, 64 Starting kernel ... LINUX started... THIS IS ASIC Linux version 2.6.36+ (root@Robert.localdomain) (gcc version 3.4.2) #3 Thu Aug 4 10:06:15 CST 2016 The CPU feqenuce set to 580 MHz MIPS CPU sleep mode enabled. PCIE: bypass PCIe DLL. PCIE: Elastic buffer control: Addr:0x68 -> 0xB4 disable all power about PCIe CPU revision is: 00019650 (MIPS 24Kc) Software DMA cache coherency Determined physical RAM map: memory: 04000000 @ 00000000 (usable) Zone PFN ranges: Normal 0x00000000 -> 0x00004000 Movable zone start PFN for each node early_node_map[1] active PFN ranges 0: 0x00000000 -> 0x00004000 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 Kernel command line: console=ttyS1,57600n8 root=/dev/mtdblock5 console=ttyS0 PID hash table entries: 256 (order: -2, 1024 bytes) Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Primary instruction cache 64kB, VIPT, , 4-waylinesize 32 bytes. Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes Writing ErrCtl register=0007e926 Readback ErrCtl register=0007e926 Memory: 61960k/65536k available (2192k kernel code, 3576k reserved, 371k data, 164k init, 0k highmem) NR_IRQS:128 console [ttyS1] enabled Calibrating delay loop... 386.04 BogoMIPS (lpj=772096) pid_max: default: 32768 minimum: 301 Mount-cache hash table entries: 512 NET: Registered protocol family 16 RALINK_GPIOMODE = 1ab11d RALINK_GPIOMODE = 18b11d PPLL_CFG1=0xe78000 MT7620 PPLL lock PPLL_DRV =0x80080504 start PCIe register access RALINK_RSTCTRL = 2400000 RALINK_CLKCFG1 = 75afffc0 *************** MT7620 PCIe RC mode ************* PCIE0 enabled init_rt2880pci done bio: create slab <bio-0> at 0 vgaarb: loaded pci 0000:00:00.0: BAR 0: can't assign mem (size 0x80000000) pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] pci 0000:00:00.0: BAR 1: set to [mem 0x20200000-0x2020ffff] (PCI address [0x20200000-0x2020ffff] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff] pci 0000:01:00.0: BAR 0: set to [mem 0x20000000-0x200fffff] (PCI address [0x20000000-0x200fffff] pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff] pci 0000:01:00.1: BAR 0: set to [mem 0x20100000-0x201fffff] (PCI address [0x20100000-0x201fffff] pci 0000:00:00.0: PCI bridge to [bus 01-01] pci 0000:00:00.0: bridge window [io disabled] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff] pci 0000:00:00.0: bridge window [mem pref disabled] BAR0 at slot 0 = 0 bus=0x0, slot = 0x0 res[0]->start = 0 res[0]->end = 0 res[1]->start = 20200000 res[1]->end = 2020ffff res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0 res[0]->start = 20000000 res[0]->end = 200fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 bus=0x1, slot = 0x0 res[0]->start = 20100000 res[0]->end = 201fffff res[1]->start = 0 res[1]->end = 0 res[2]->start = 0 res[2]->end = 0 res[3]->start = 0 res[3]->end = 0 res[4]->start = 0 res[4]->end = 0 res[5]->start = 0 res[5]->end = 0 Switching to clocksource Ralink Systick timer NET: Registered protocol family 2 IP route cache hash table entries: 1024 (order: 0, 4096 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP reno registered UDP hash table entries: 256 (order: 0, 4096 bytes) UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) NET: Registered protocol family 1 Load Ralink Timer0 Module Load Ralink Timer1 Module squashfs: version 4.0 (2009/01/31) Phillip Lougher msgmni has been set to 121 io scheduler noop registered (default) Init GPIO Interrupt ***********Init LED Driver Finishing***************** Ralink_gpio_init_irq LED & GPIO & LAN Status Driver LED_VERSION Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x10000500 (irq = 37) is a 16550A serial8250: ttyS1 at MMIO 0x10000c00 (irq = 12) is a 16550A brd: module loaded deice id : ef 40 18 0 0 (40180000) W25Q128BV(ef 40180000) (16384 Kbytes) mtd .name = raspi, .size = 0x01000000 (0M) .erasesize = 0x00000010 (0K) .numeraseregions = 65536 Creating 8 MTD partitions on "raspi": 0x000000000000-0x000000030000 : "Bootloader" 0x000000030000-0x000000040000 : "Config" 0x000000040000-0x000000050000 : "Factory" 0x000000050000-0x000000070000 : "Cimage" 0x000000070000-0x000000190000 : "Kernel" 0x000000190000-0x000000fe0000 : "RootFS" 0x000000070000-0x000000fe0000 : "Uimage" 0x000000fe0000-0x000001000000 : "FreeSpace" rdm_major = 240 SMACCR1 -- : 0x000074da SMACCR0 -- : 0x38fb0786 Ralink APSoC Ethernet Driver Initilization. v3.0 256 rx/tx descriptors allocated, mtu = 1500! SMACCR1 -- : 0x000074da SMACCR0 -- : 0x38fb0786 PROC INIT OK! PPP generic driver version 2.4.2 NET: Registered protocol family 24 PPTP driver version 0.8.5 tun: Universal TUN/TAP device driver, 1.6 tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com> Ralink APSoC Hardware Watchdog Timer u32 classifier Performance counters on Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (968 buckets, 3872 max) ctnetlink v0.93: registering with nfnetlink. matchsize=264 xt_time: kernel timezone is -0000 GRE over IPv4 demultiplexor driver gre: can't add protocol ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Linux TCP cubic registered NET: Registered protocol family 17 @@@@@@@@@@@@@@@@@@@@@ Begin creat a_g_isolation proc @@@@@@@@@@@@@@@@ @@@@@@@@@@@@@@@@@@@@@ End of creat a_g_isolation proc @@@@@@@@@@@@@@@@ dnshijack L2TP core driver, V2.0 PPPoL2TP kernel driver, V2.0 L2TP IP encapsulation support (L2TPv3) L2TP netlink interface L2TP ethernet pseudowire support (L2TPv3) 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly on device 31:5. Freeing unused kernel memory: 164k freed init started: BusyBox v1.15.2 (2016-08-04 10:00:27 CST) starting pid 19, tty '': '/etc/rc.sh' cannot run '/etc/rc.sh': No such file or directory starting pid 20, tty '': '-/bin/sh' console. Algorithmics/MIPS FPU Emulator v1.5 BusyBox v1.15.2 (2016-08-04 10:00:27 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. Thu Aug 4 09:57:43 UTC 2016 BR-6278AC HW Setting...(by EEPROM) Non-default, exit! Set: phy[4].reg[0] = 3900 16384 bytes (0 MB) copied,0.018 seconds,0.000 MB/s gzip: invalid magic 32768 bytes (0 MB) copied,0.041 seconds,0.000 MB/s gzip: invalid magic / Started WatchDog Timer. Started WatchDog Timer. watchdog: ioRaeth v3.0 (ctTaskletl ,SkbRecycle0x) c0045 phy_tx_ring = 0x03543000, tx_ring = 0xa3543000 phy_rx_ring0 = 0x03544000, rx_ring0 = 0xa3544000 SMACCR1 -- : 0x000074da SMACCR0 -- : 0x38fb0786 70CDMA_CSG_CFG = 81000000 6 GDMA1_FWD_CFG = 20010000 failed: Inappropriate ioctl for device ==> WAN MTU 1500 device eth2 entered promiscuous mode Initialize rai0 interface ****************Use External RADIUS****************** Initialize ra0 interface ****************Use External RADIUS****************** >>> wireless_driver() >>> Loading 2.4G Wireless Driver >>> Loading rt2860v2_ap rt2860v2_ap: module license 'unspecified' taints kernel. Disabling lock debugging due to kernel taint === pAd = c06dd000, size = 924072 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 AP Driver version-2.7.2.0 RX DESC a35aa000 size = 2048 RTMP_TimerListAdd: add timer obj c077f4e8! RTMP_TimerListAdd: add timer obj c0741454! RTMP_TimerListAdd: add timer obj c0741428! RTMP_TimerListAdd: add timer obj c0741480! RTMP_TimerListAdd: add timer obj c07413fc! RTMP_TimerListAdd: add timer obj c06e53f0! RTMP_TimerListAdd: add timer obj c06e4c38! RTMP_TimerListAdd: add timer obj c06e53c0! RTMP_TimerListAdd: add timer obj c06e56fc! RTMP_TimerListAdd: add timer obj c06e563c! RTMP_TimerListAdd: add timer obj c06e566c! RTMP_TimerListAdd: add timer obj c06e8970! RTMP_TimerListAdd: add timer obj c06e81b8! RTMP_TimerListAdd: add timer obj c06e8940! RTMP_TimerListAdd: add timer obj c06e8c7c! RTMP_TimerListAdd: add timer obj c06e8bbc! RTMP_TimerListAdd: add timer obj c06e8bec! RTMP_TimerListAdd: add timer obj c06ebef0! RTMP_TimerListAdd: add timer obj c06eb738! RTMP_TimerListAdd: add timer obj c06ebec0! RTMP_TimerListAdd: add timer obj c06ec1fc! RTMP_TimerListAdd: add timer obj c06ec13c! RTMP_TimerListAdd: add timer obj c06ec16c! RTMP_TimerListAdd: add timer obj c06ef470! RTMP_TimerListAdd: add timer obj c06eecb8! RTMP_TimerListAdd: add timer obj c06ef440! RTMP_TimerListAdd: add timer obj c06ef77c! RTMP_TimerListAdd: add timer obj c06ef6bc! RTMP_TimerListAdd: add timer obj c06ef6ec! RTMP_TimerListAdd: add timer obj c06f29f0! RTMP_TimerListAdd: add timer obj c06f2238! RTMP_TimerListAdd: add timer obj c06f29c0! RTMP_TimerListAdd: add timer obj c06f2cfc! RTMP_TimerListAdd: add timer obj c06f2c3c! RTMP_TimerListAdd: add timer obj c06f2c6c! RTMP_TimerListAdd: add timer obj c06f5f70! RTMP_TimerListAdd: add timer obj c06f57b8! RTMP_TimerListAdd: add timer obj c06f5f40! RTMP_TimerListAdd: add timer obj c06f627c! RTMP_TimerListAdd: add timer obj c06f61bc! RTMP_TimerListAdd: add timer obj c06f61ec! RTMP_TimerListAdd: add timer obj c06f94f0! RTMP_TimerListAdd: add timer obj c06f8d38! RTMP_TimerListAdd: add timer obj c06f94c0! RTMP_TimerListAdd: add timer obj c06f97fc! RTMP_TimerListAdd: add timer obj c06f973c! RTMP_TimerListAdd: add timer obj c06f976c! RTMP_TimerListAdd: add timer obj c06fca70! RTMP_TimerListAdd: add timer obj c06fc2b8! RTMP_TimerListAdd: add timer obj c06fca40! RTMP_TimerListAdd: add timer obj c06fcd7c! RTMP_TimerListAdd: add timer obj c06fccbc! RTMP_TimerListAdd: add timer obj c06fccec! RTMP_TimerListAdd: add timer obj c0743c7c! RTMP_TimerListAdd: add timer obj c07434c4! RTMP_TimerListAdd: add timer obj c0743c4c! RTMP_TimerListAdd: add timer obj c0743f88! RTMP_TimerListAdd: add timer obj c0743cac! RTMP_TimerListAdd: add timer obj c0743cdc! RTMP_TimerListAdd: add timer obj c0743d0c! RTMP_TimerListAdd: add timer obj c0755e54! RTMP_TimerListAdd: add timer obj c0755f70! RTMP_TimerListAdd: add timer obj c0755e80! RTMP_TimerListAdd: add timer obj c074437c! RTMP_TimerListAdd: add timer obj c06e2504! RTMP_TimerListAdd: add timer obj c06e5a84! RTMP_TimerListAdd: add timer obj c06e9004! RTMP_TimerListAdd: add timer obj c06ec584! RTMP_TimerListAdd: add timer obj c06efb04! RTMP_TimerListAdd: add timer obj c06f3084! RTMP_TimerListAdd: add timer obj c06f6604! RTMP_TimerListAdd: add timer obj c06f9b84! RTMP_TimerListAdd: add timer obj c0744084! default ApCliAPSDCapable[0]=1 RTMPSetDefaultChannel() : default channel to 1 1. Phy Mode = 9 2. Phy Mode = 9 E2PROM: D0 target power=0xff20 E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = -1, D2 = 11, CalCode = 28 !!! RT6352_Temperature_Init : BBPR49 = 0xffffffff RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5 Current Temperature from BBP_R49=0xfffffff7 TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= 0, phase=3d) IQCalibration Start! IQCalibration Done! CH = 1, (gain= 0, phase= 2) TX IQ Calibration Done! internal ALC is not enabled in NVM ! MCS Set = ff ff 00 00 01 SYNC - BBP R4 to 20MHz.l The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8 @@@ ed_monitor_init : ===> RTMP_TimerListAdd: add timer obj c07be970! @@@ ed_monitor_init : <=== Main bssid = 74:da:38:fb:07:86 <==== rt28xx_init, Status=0 0x1300 = 00064300 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8 @@@ APStop: go to ed_monitor_exit()!! @@@ ed_monitor_exit : ===> @@@ ed_monitor_exit : <=== >>> wireless_driver() >>> Loading 5G Wireless Driver >>> Loading MT7610_ap === pAd = c0d02000, size = 1360280 === <-- RTMPAllocTxRxRingMemory, Status=0 <-- RTMPAllocAdapterBlock, Status=0 device_id =0x7650 ==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0xff000002 MACVersion = 0x76502000 load fw spent 16ms RX DESC a2bff000 size = 2048 RX1 DESC a2a84000 size = 2048 @@@ 7610 AdvContral=0 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Not Equal! IGMP Snooping Enable=1 1. Phy Mode = 49 2. Phy Mode = 49 ext_pa_current_setting = 1 MT76x0_TssiTableAdjust: upper_bound = 0x7F decimal: 127 MT76x0_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128 *** MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -16 -10 -4 * 0 * 6 13 19 127 127 127 127, offset=-8, tuning=1 MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -24 -18 -12 * -8 * -2 5 11 119 119 119 119, offset=-8, tuning=1 mp_temperature=0xfffffff9, step = +0 MT76x0_TssiTableAdjust: upper_bound = 0x7F decimal: 127 MT76x0_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128 *** MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -18 -13 -5 * -8 * 4 13 20 127 127 127 127, offset=-8, tuning=1 MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -26 -21 -13 * -8 * -4 5 12 119 119 119 119, offset=-8, tuning=1 mp_temperature=0xfffffff9, step = +0 3. Phy Mode = 49 AntCfgInit: primary/secondary ant 0/1 ChipStructAssign(): RALINK6590 hook ! bAutoTxAgcG = 1 MCS Set = ff 00 00 00 01 MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42 APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== Main bssid = 74:da:38:fb:07:87 <==== rt28xx_init, Status=0 MT76x0_Calibration - Channel = 42, bPowerOn = 1, bSaveCal = 1 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 42, param = 0x301, bSave = 1, CalibrationMode = 255 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 136, param = 0x401, bSave = 1, CalibrationMode = 255 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 155, param = 0x501, bSave = 1, CalibrationMode = 255 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_Calibration - Channel = 36, bPowerOn = 0, bSaveCal = 0 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 36, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_Calibration - Channel = 40, bPowerOn = 0, bSaveCal = 0 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 40, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_Calibration - Channel = 44, bPowerOn = 0, bSaveCal = 0 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 44, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_Calibration - Channel = 48, bPowerOn = 0, bSaveCal = 0 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 48, param = 0x701, bSave = 0, CalibrationMode = 255 @@@ ed_monitor_exit : ===> @@@ ed_monitor_exit : <=== MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=3, PrimCh=40, HT-CentCh=38, VHT-CentCh=42 APStartUp(): AP Set CentralFreq at 42(Prim=40, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) MT76x0_Calibration - Channel = 42, bPowerOn = 0, bSaveCal = 0 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== 0x1300 = 00064320 RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! <7610>The UUID Hex string is:bc329e001dd811b2860174da38fb0787 <7610>The UUID ASCII string is:bc329e00-1dd8-11b2-8601-74da38fb0787! <7610>The UUID Hex string is:bc329e001dd811b2860176da38f80787 <7610>The UUID ASCII string is:bc329e00-1dd8-11b2-8601-76da38f80787! <7610>The UUID Hex string is:bc329e001dd811b2860176da38f90787 <7610>The UUID ASCII string is:bc329e00-1dd8-11b2-8601-76da38f90787! <7610>The UUID Hex string is:bc329e001dd811b2860176da38fa0787 <7610>The UUID ASCII string is:bc329e00-1dd8-11b2-8601-76da38fa0787! <7610>The UUID Hex string is:bc329e001dd811b2860176da38fb0787 <7610>The UUID ASCII string is:bc329e00-1dd8-11b2-8601-76da38fb0787! <7610>The UUID Hex string is:bc329e001dd811b2860174da38fb0787 <7610>The UUID ASCII string is:bc329e00-1dd8-11b2-8601-74da38fb0787! edcca_tx_stop_start():stop tx edcca_tx_stop_start():start tx @@@ ed_monitor_exit : ===> @@@ ed_monitor_exit : <=== ==>MT76x0_WLAN_ChipOnOff(): OnOff:0, pAd->WlanFunCtrl:0xff000003, Reg-WlanFunCtrl=0xff000003 Setup BRIDGE interface ifconfig: ioctl 0x8913 failed: No such device bridge br0 doesn't exist; can't delete it [bridge] Setup bridge... device eth2.1 entered promiscuous mode route: ioctl 0x890c failed: No such process route: ioctl 0x890c failed: No such process ==>MT76x0_WLAN_ChipOnOff(): OnOff:1, pAd->WlanFunCtrl:0xff000000, Reg-WlanFunCtrl=0xff000000 MACVersion = 0x76502000 load fw spent 16ms RX DESC a2bff000 size = 2048 RX1 DESC a2a84000 size = 2048 @@@ 7610 AdvContral=0 cfg_mode=14 cfg_mode=14 wmode_band_equal(): Band Not Equal! IGMP Snooping Enable=1 1. Phy Mode = 49 2. Phy Mode = 49 ext_pa_current_setting = 1 MT76x0_TssiTableAdjust: upper_bound = 0x7F decimal: 127 MT76x0_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128 *** MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -16 -10 -4 * 0 * 6 13 19 127 127 127 127, offset=-8, tuning=1 MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -24 -18 -12 * -8 * -2 5 11 119 119 119 119, offset=-8, tuning=1 mp_temperature=0xfffffff9, step = +0 MT76x0_TssiTableAdjust: upper_bound = 0x7F decimal: 127 MT76x0_TssiTableAdjust: lower_bound = 0xFFFFFF80 decimal: -128 *** MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -18 -13 -5 * -8 * 4 13 20 127 127 127 127, offset=-8, tuning=1 MT76x0_TssiTableAdjust: A Tssi[-7 .. +7] = -128 -128 -128 -128 -26 -21 -13 * -8 * -4 5 12 119 119 119 119, offset=-8, tuning=1 mp_temperature=0xfffffff9, step = +0 3. Phy Mode = 49 AntCfgInit: primary/secondary ant 0/1 ChipStructAssign(): RALINK6590 hook ! bAutoTxAgcG = 1 MCS Set = ff 00 00 00 01 MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=1, PrimCh=36, HT-CentCh=38, VHT-CentCh=42 APStartUp(): AP Set CentralFreq at 42(Prim=36, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== Main bssid = 74:da:38:fb:07:87 <==== rt28xx_init, Status=0 MT76x0_Calibration - Channel = 42, bPowerOn = 1, bSaveCal = 1 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 42, param = 0x301, bSave = 1, CalibrationMode = 255 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 136, param = 0x401, bSave = 1, CalibrationMode = 255 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 155, param = 0x501, bSave = 1, CalibrationMode = 255 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_Calibration - Channel = 36, bPowerOn = 0, bSaveCal = 0 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 36, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_Calibration - Channel = 40, bPowerOn = 0, bSaveCal = 0 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 40, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_Calibration - Channel = 44, bPowerOn = 0, bSaveCal = 0 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 44, param = 0x701, bSave = 0, CalibrationMode = 255 MT76x0_Calibration - Channel = 48, bPowerOn = 0, bSaveCal = 0 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 48, param = 0x701, bSave = 0, CalibrationMode = 255 @@@ ed_monitor_exit : ===> @@@ ed_monitor_exit : <=== MT76x0_ChipBBPAdjust():rf_bw=2, ext_ch=3, PrimCh=40, HT-CentCh=38, VHT-CentCh=42 APStartUp(): AP Set CentralFreq at 42(Prim=40, HT-CentCh=38, VHT-CentCh=42, BBP_BW=2) MT76x0_Calibration - Channel = 42, bPowerOn = 0, bSaveCal = 0 FullCalibration(): docal = [0006] valid bit[0] FullCalibration - Channel = 42, param = 0x701, bSave = 0, CalibrationMode = 255 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== 0x1300 = 00064320 RTMPDrvOpen(1):Check if PDMA is idle! RTMPDrvOpen(2):Check if PDMA is idle! <7610>The UUID Hex string is:bc329e001dd811b2860174da38fb0787 <7610>The UUID ASCII string is:bc329e00-1dd8-11b2-8601-74da38fb0787! <7610>The UUID Hex string is:bc329e001dd811b2860176da38f80787 <7610>The UUID ASCII string is:bc329e00-1dd8-11b2-8601-76da38f80787! <7610>The UUID Hex string is:bc329e001dd811b2860176da38f90787 <7610>The UUID ASCII string is:bc329e00-1dd8-11b2-8601-76da38f90787! <7610>The UUID Hex string is:bc329e001dd811b2860176da38fa0787 <7610>The UUID ASCII string is:bc329e00-1dd8-11b2-8601-76da38fa0787! <7610>The UUID Hex string is:bc329e001dd811b2860176da38fb0787 <7610>The UUID ASCII string is:bc329e00-1dd8-11b2-8601-76da38fb0787! <7610>The UUID Hex string is:bc329e001dd811b2860174da38fb0787 <7610>The UUID ASCII string is:bc329e00-1dd8-11b2-8601-74da38fb0787! route: ioctl 0x890c failed: No such process route: ioctl 0x890c failed: No such process edcca_tx_stop_start():stop tx device rai0 entered promiscuous mode RX DESC a35aa000 size = 2048 RTMP_TimerListAdd: add timer obj c077f4e8! RTMP_TimerListAdd: add timer obj c0741454! RTMP_TimerListAdd: add timer obj c0741428! RTMP_TimerListAdd: add timer obj c0741480! RTMP_TimerListAdd: add timer obj c07413fc! RTMP_TimerListAdd: add timer obj c06e53f0! RTMP_TimerListAdd: add timer obj c06e4c38! RTMP_TimerListAdd: add timer obj c06e53c0! RTMP_TimerListAdd: add timer obj c06e56fc! RTMP_TimerListAdd: add timer obj c06e563c! RTMP_TimerListAdd: add timer obj c06e566c! RTMP_TimerListAdd: add timer obj c06e8970! RTMP_TimerListAdd: add timer obj c06e81b8! RTMP_TimerListAdd: add timer obj c06e8940! RTMP_TimerListAdd: add timer obj c06e8c7c! RTMP_TimerListAdd: add timer obj c06e8bbc! RTMP_TimerListAdd: add timer obj c06e8bec! RTMP_TimerListAdd: add timer obj c06ebef0! RTMP_TimerListAdd: add timer obj c06eb738! RTMP_TimerListAdd: add timer obj c06ebec0! RTMP_TimerListAdd: add timer obj c06ec1fc! RTMP_TimerListAdd: add timer obj c06ec13c! RTMP_TimerListAdd: add timer obj c06ec16c! RTMP_TimerListAdd: add timer obj c06ef470! RTMP_TimerListAdd: add timer obj c06eecb8! RTMP_TimerListAdd: add timer obj c06ef440! RTMP_TimerListAdd: add timer obj c06ef77c! RTMP_TimerListAdd: add timer obj c06ef6bc! RTMP_TimerListAdd: add timer obj c06ef6ec! RTMP_TimerListAdd: add timer obj c06f29f0! RTMP_TimerListAdd: add timer obj c06f2238! RTMP_TimerListAdd: add timer obj c06f29c0! RTMP_TimerListAdd: add timer obj c06f2cfc! RTMP_TimerListAdd: add timer obj c06f2c3c! RTMP_TimerListAdd: add timer obj c06f2c6c! RTMP_TimerListAdd: add timer obj c06f5f70! RTMP_TimerListAdd: add timer obj c06f57b8! RTMP_TimerListAdd: add timer obj c06f5f40! RTMP_TimerListAdd: add timer obj c06f627c! RTMP_TimerListAdd: add timer obj c06f61bc! RTMP_TimerListAdd: add timer obj c06f61ec! RTMP_TimerListAdd: add timer obj c06f94f0! RTMP_TimerListAdd: add timer obj c06f8d38! RTMP_TimerListAdd: add timer obj c06f94c0! RTMP_TimerListAdd: add timer obj c06f97fc! RTMP_TimerListAdd: add timer obj c06f973c! RTMP_TimerListAdd: add timer obj c06f976c! edcca_tx_stop_start():start tx RTMP_TimerListAdd: add timer obj c06fca70! RTMP_TimerListAdd: add timer obj c06fc2b8! RTMP_TimerListAdd: add timer obj c06fca40! RTMP_TimerListAdd: add timer obj c06fcd7c! RTMP_TimerListAdd: add timer obj c06fccbc! RTMP_TimerListAdd: add timer obj c06fccec! RTMP_TimerListAdd: add timer obj c0743c7c! RTMP_TimerListAdd: add timer obj c07434c4! RTMP_TimerListAdd: add timer obj c0743c4c! RTMP_TimerListAdd: add timer obj c0743f88! RTMP_TimerListAdd: add timer obj c0743cac! RTMP_TimerListAdd: add timer obj c0743cdc! RTMP_TimerListAdd: add timer obj c0743d0c! RTMP_TimerListAdd: add timer obj c0755e54! RTMP_TimerListAdd: add timer obj c0755f70! RTMP_TimerListAdd: add timer obj c0755e80! RTMP_TimerListAdd: add timer obj c074437c! RTMP_TimerListAdd: add timer obj c06e2504! RTMP_TimerListAdd: add timer obj c06e5a84! RTMP_TimerListAdd: add timer obj c06e9004! RTMP_TimerListAdd: add timer obj c06ec584! RTMP_TimerListAdd: add timer obj c06efb04! RTMP_TimerListAdd: add timer obj c06f3084! RTMP_TimerListAdd: add timer obj c06f6604! RTMP_TimerListAdd: add timer obj c06f9b84! RTMP_TimerListAdd: add timer obj c0744084! edcca_tx_stop_start(cnt=10000,time=0x80):stop MTx,macStatus=0x1! edcca_tx_stop_start():stop tx default ApCliAPSDCapable[0]=1 RTMPSetDefaultChannel() : default channel to 1 1. Phy Mode = 9 2. Phy Mode = 9 E2PROM: D0 target power=0xff20 E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = -1, D2 = 10, CalCode = 26 !!! RT6352_Temperature_Init : BBPR49 = 0xffffffff RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5 Current Temperature from BBP_R49=0xfffffff7 TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= f, phase= 1) IQCalibration Start! IQCalibration Done! CH = 1, (gain= 0, phase= 2) TX IQ Calibration Done! internal ALC is not enabled in NVM ! MCS Set = ff ff 00 00 01 SYNC - BBP R4 to 20MHz.l edcca_tx_stop_start():start tx The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8 @@@ ed_monitor_init : ===> RTMP_TimerListAdd: add timer obj c07be970! @@@ ed_monitor_init : <=== Main bssid = 74:da:38:fb:07:86 <==== rt28xx_init, Status=0 0x1300 = 00064300 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== route: ioctl 0x890c failed: No such process route: ioctl 0x890c failed: No such process device ra0 entered promiscuous mode br0: port 3(ra0) entering forwarding state br0: port 3(ra0) entering forwarding state br0: port 2(rai0) entering forwarding state br0: port 2(rai0) entering forwarding state br0: port 1(eth2.1) entering forwarding state br0: port 1(eth2.1) entering forwarding state route: ioctl 0x890c failed: No such process route: ioctl 0x890c failed: No such process route: ioctl 0x890c failed: No such process route: ioctl 0x890c failed: No such process Static DHCP Leases disable! route: ioctl 0x890c failed: No such process route: ioctl 0xbr0: port 3(ra0) entering forwarding state 89br0: port 2(rai0) entering forwarding state 0cbr0: port 1(eth2.1) entering forwarding state failed: No such process Set: phy[1].reg[0] = 3900 Set: phy[2].reg[0] = 3900 Set: phy[3].reg[0] = 3900 Set: phy[1].reg[0] = 3300 Set: phy[2].reg[0] = 3300 Set: phy[3].reg[0] = 3300 br0: port 3(ra0) entering forwarding state br0: port 3(ra0) entering forwarding state br0: port 2(rai0) entering forwarding state br0: port 2(rai0) entering forwarding state br0: port 1(eth2.1) entering forwarding state br0: port 1(eth2.1) entering forwarding state Set: phy[1].reg[0] = 3900 Set: phy[2].reg[0] = 3900 Set: phy[3].reg[0] = 3900 Set: phy[1].reg[0] = 3300 Set: phy[2].reg[0] = 3300 Set: phy[3].reg[0] = 3300 Setup WAN interface kill: you need to specify whom to kill Close Wan(eth2.2) Interface!! device eth2 is not a slave of br0 device eth2.1 is already a member of a bridge; can't enslave it to bridge br0. =====config-vlan.sh Start 3 LLLLW====== Special Tag Disabled REG_ESW_WT_MAC_ATC is 0x7ff0002 done. Set: phy[4].reg[0] = 3300 ********************************************************************** * Enable WSC_UPnP * ********************************************************************** ********************************************************************** * Enable LLTD * ********************************************************************** killall: lld2d: no process killed libupnp: using UDP SSDP_PORT = 1900 libupnp: using UDP SSDP_PORT = 1900 killall: snmpd: no process killed udhcpc (v1.15.2) started into eth2.2.deconfig ------> 802.1x--------->Enter ------> 802.1x------>Exit killall: radiusd: no process killed RADIUS server disable !! kill: you need to specify whom to kill dns_hijack_enabled = 1 ********************************************************************** * FREE Page,Dentries and Inodes Cache * ********************************************************************** >>> Update system time every 30min MemFree: 40380 kB Cached: 3212 kB >>> Check new fw version is every week 7 00:00. >>> Close iQsetup killall: crond: no process killed boa: server version Boa/0.94.14rc21 boa: server built Aug 4 2016 at 10:01:13. boa: starting server pid=1021, port 80 No dnrd daemon found. Exiting. cat: can't open '/etc/resolv.conf': No such file or directory Notice: caching turned off killall: gpio: no process killed ralink_gpio:ioctl GPIO REG info.irq = 1 Channel_Number 2 ~ 10 Min_Channel_Number = 2 Min_Channel_Count = 0 2.4G AutoThe 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8 Channel=2 @@@ APStop: go to ed_monitor_exit()!! @@@ ed_monitor_exit : ===> @@@ ed_monitor_exit : <=== br0: port 3(ra0) entering forwarding state RX DESC a35aa000 size = 2048 RTMP_TimerListAdd: add timer obj c077f4e8! RTMP_TimerListAdd: add timer obj c0741454! RTMP_TimerListAdd: add timer obj c0741428! RTMP_TimerListAdd: add timer obj c0741480! RTMP_TimerListAdd: add timer obj c07413fc! RTMP_TimerListAdd: add timer obj c06e53f0! RTMP_TimerListAdd: add timer obj c06e4c38! RTMP_TimerListAdd: add timer obj c06e53c0! RTMP_TimerListAdd: add timer obj c06e56fc! RTMP_TimerListAdd: add timer obj c06e563c! RTMP_TimerListAdd: add timer obj c06e566c! RTMP_TimerListAdd: add timer obj c06e8970! RTMP_TimerListAdd: add timer obj c06e81b8! RTMP_TimerListAdd: add timer obj c06e8940! RTMP_TimerListAdd: add timer obj c06e8c7c! RTMP_TimerListAdd: add timer obj c06e8bbc! RTMP_TimerListAdd: add timer obj c06e8bec! RTMP_TimerListAdd: add timer obj c06ebef0! RTMP_TimerListAdd: add timer obj c06eb738! RTMP_TimerListAdd: add timer obj c06ebec0! RTMP_TimerListAdd: add timer obj c06ec1fc! RTMP_TimerListAdd: add timer obj c06ec13c! RTMP_TimerListAdd: add timer obj c06ec16c! RTMP_TimerListAdd: add timer obj c06ef470! RTMP_TimerListAdd: add timer obj c06eecb8! RTMP_TimerListAdd: add timer obj c06ef440! RTMP_TimerListAdd: add timer obj c06ef77c! RTMP_TimerListAdd: add timer obj c06ef6bc! RTMP_TimerListAdd: add timer obj c06ef6ec! RTMP_TimerListAdd: add timer obj c06f29f0! RTMP_TimerListAdd: add timer obj c06f2238! RTMP_TimerListAdd: add timer obj c06f29c0! RTMP_TimerListAdd: add timer obj c06f2cfc! RTMP_TimerListAdd: add timer obj c06f2c3c! RTMP_TimerListAdd: add timer obj c06f2c6c! RTMP_TimerListAdd: add timer obj c06f5f70! RTMP_TimerListAdd: add timer obj c06f57b8! RTMP_TimerListAdd: add timer obj c06f5f40! RTMP_TimerListAdd: add timer obj c06f627c! RTMP_TimerListAdd: add timer obj c06f61bc! RTMP_TimerListAdd: add timer obj c06f61ec! RTMP_TimerListAdd: add timer obj c06f94f0! RTMP_TimerListAdd: add timer obj c06f8d38! RTMP_TimerListAdd: add timer obj c06f94c0! RTMP_TimerListAdd: add timer obj c06f97fc! RTMP_TimerListAdd: add timer obj c06f973c! RTMP_TimerListAdd: add timer obj c06f976c! RTMP_TimerListAdd: add timer obj c06fca70! RTMP_TimerListAdd: add timer obj c06fc2b8! RTMP_TimerListAdd: add timer obj c06fca40! RTMP_TimerListAdd: add timer obj c06fcd7c! RTMP_TimerListAdd: add timer obj c06fccbc! RTMP_TimerListAdd: add timer obj c06fccec! RTMP_TimerListAdd: add timer obj c0743c7c! RTMP_TimerListAdd: add timer obj c07434c4! RTMP_TimerListAdd: add timer obj c0743c4c! RTMP_TimerListAdd: add timer obj c0743f88! RTMP_TimerListAdd: add timer obj c0743cac! RTMP_TimerListAdd: add timer obj c0743cdc! RTMP_TimerListAdd: add timer obj c0743d0c! RTMP_TimerListAdd: add timer obj c0755e54! RTMP_TimerListAdd: add timer obj c0755f70! RTMP_TimerListAdd: add timer obj c0755e80! RTMP_TimerListAdd: add timer obj c074437c! RTMP_TimerListAdd: add timer obj c06e2504! RTMP_TimerListAdd: add timer obj c06e5a84! RTMP_TimerListAdd: add timer obj c06e9004! RTMP_TimerListAdd: add timer obj c06ec584! RTMP_TimerListAdd: add timer obj c06efb04! RTMP_TimerListAdd: add timer obj c06f3084! RTMP_TimerListAdd: add timer obj c06f6604! RTMP_TimerListAdd: add timer obj c06f9b84! RTMP_TimerListAdd: add timer obj c0744084! default ApCliAPSDCapable[0]=1 1. Phy Mode = 9 2. Phy Mode = 9 E2PROM: D0 target power=0xff20 E2PROM: 40 MW Power Delta= 0 3. Phy Mode = 9 AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! Initialize RF Central Registers for E3 !!! Initialize RF Channel Registers for E2 !!! Initialize RF Channel Registers for E3 !!! Initialize RF DCCal Registers for E2 !!! Initialize RF DCCal Registers for E3 !!! D1 = -1, D2 = 10, CalCode = 26 !!! RT6352_Temperature_Init : BBPR49 = 0xffffffff RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff5 Current Temperature from BBP_R49=0xfffffff9 TX BW Filter Calibration !!! RX BW Filter Calibration !!! LOFT Calibration Done! IQCalibration Start! IQCalibration Done! CH = 0, (gain= 1, phase=3e) IQCalibration Start! IQCalibration Done! CH = 1, (gain= 0, phase= 2) TX IQ Calibration Done! internal ALC is not enabled in NVM ! MCS Set = ff ff 00 00 01 The 8-BSSID mode is enabled, the BSSID byte5 MUST be the multiple of 8 @@@ ed_monitor_init : ===> RTMP_TimerListAdd: add timer obj c07be970! @@@ ed_monitor_init : <=== Main bssid = 74:da:38:fb:07:86 <==== rt28xx_init, Status=0 0x1300 = 00064300 @@@ ed_monitor_init : ===> @@@ ed_monitor_init : <=== br0: port 3(ra0) entering forwarding state br0: port 3(ra0) entering forwarding state [AutoCheckFW] Run 1 [AutoCheckFW] 09:58:41 [AutoCheckFW] sleep 75 sec.. [AutoCheckFW] 09:59:56 curl: (6) Couldn't resolve host 'www.edimax.com' [AutoCheckFW] Run 2 [AutoCheckFW] 10:00:00 [AutoCheckFW] sleep 75 sec.. [AutoCheckFW] 10:01:15 curl: (6) Couldn't resolve host 'www.edimax.com' edcca_tx_stop_start(cnt=10000,time=0x80):stop MTx,macStatus=0x1! edcca_tx_stop_start():stop tx [AutoCheckFW] Run 3 [AutoCheckFW] 10:01:18 [AutoCheckFW] sleep 75 sec.. edcca_tx_stop_start():start tx edcca_tx_stop_start(cnt=10000,time=0x80):stop MTx,macStatus=0x1! edcca_tx_stop_start():stop tx [AutoCheckFW] 10:02:33 curl: (6) Couldn't resolve host 'www.edimax.com' [AutoCheckFW] http://www.edimax.com/fw/wifirouter/BR-6208ACv2/wifirouter_fw_info.txt [AutoCheckFW] Download error, exit! edcca_tx_stop_start():start tx edcca_tx_stop_start():stop tx edcca_tx_stop_start():start tx edcca_tx_stop_start(cnt=10000,time=0x80):stop MTx,macStatus=0x1! edcca_tx_stop_start():stop tx edcca_tx_stop_start():start tx edcca_tx_stop_start(cnt=10000,time=0x80):stop MTx,macStatus=0x1! edcca_tx_stop_start():stop tx


U-Boot 1.1.3 (Aug 2 2016 - 13:38:35) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fb4000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. ************** Init GPIO Pin Start ************** RALINK_GPIOMODE_UARTF=0x00009801 ************** Init GPIO Pin Done ************** spi_wait_nsec: 29 spi device id: ef 40 18 0 0 (40180000) find flash: W25Q128BV raspi_read: from:30000 len:1000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.1.2.0 -------------------------------------------- ASIC 7620_MP (Port5<->None) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:Aug 2 2016 Time:13:38:35 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 5: Load ucos code to SDRAM via TFTP Client. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 0 3: System Boot system code via Flash. ## Booting image at bc070000 ... raspi_read: from:70000 len:40 Magic number at 0xBC070000 raspi_read: from:70014 len:40 Image Name: MIPS OpenWrt Linux-5.15.147 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 2456406 Bytes = 2.3 MB Load Address: 80000000 Entry Point: 80000000 raspi_read: from:70054 len:257b56 Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... [ 0.000000] Linux version 5.15.147 (builder@buildhost) (mipsel-openwrt-linux-musl-gcc (OpenWrt GCC 12.3.0 r24893-b34e6de7da) 12.3.0, GNU ld (GNU Binutils) 2.40.0) #0 Wed Jan 24 12:08:36 2024 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is Edimax BR-6208AC v2 [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240 [ 0.000000] Kernel command line: console=ttyS0,57600 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000000] Writing ErrCtl register=0007e006 [ 0.000000] Readback ErrCtl register=0007e006 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 55492K/65536K available (5972K kernel code, 607K rwdata, 1292K rodata, 1208K init, 225K bss, 10044K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns [ 0.000000] systick: enable autosleep mode [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns [ 0.000002] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns [ 0.015581] Calibrating delay loop... 385.84 BogoMIPS (lpj=1929216) [ 0.087809] pid_max: default: 32768 minimum: 301 [ 0.098157] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.112584] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.138216] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns [ 0.157695] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.171425] pinctrl core: initialized pinctrl subsystem [ 0.183562] NET: Registered PF_NETLINK/PF_ROUTE protocol family [ 0.196012] thermal_sys: Registered thermal governor 'step_wise' [ 0.693171] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.716133] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.728737] rt2880_gpio 10000638.gpio: registering 16 gpios [ 0.739746] rt2880_gpio 10000638.gpio: registering 16 irq handlers [ 0.752455] rt2880_gpio 10000660.gpio: registering 32 gpios [ 0.763532] rt2880_gpio 10000660.gpio: registering 32 irq handlers [ 0.777894] PCI host bridge to bus 0000:00 [ 0.785966] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] [ 0.799579] pci_bus 0000:00: root bus resource [io 0x10160000-0x1016ffff] [ 0.813252] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.829059] pci 0000:00:00.0: [1814:0801] type 01 class 0x060400 [ 0.840958] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 0.853409] pci 0000:00:00.0: reg 0x14: [mem 0x00000000-0x0000ffff] [ 0.865953] pci 0000:00:00.0: supports D1 [ 0.873818] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.887642] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.903793] pci 0000:01:00.0: [14c3:7650] type 00 class 0x028000 [ 0.915664] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff] [ 0.928233] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.940555] pci 0000:01:00.1: [14c3:8650] type 00 class 0x0d1100 [ 0.952421] pci 0000:01:00.1: reg 0x10: [mem 0x00000000-0x000fffff] [ 0.964982] pci 0000:01:00.1: supports D1 [ 0.972795] pci 0000:01:00.1: PME# supported from D0 D1 D3hot D3cold [ 0.987738] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 1.000807] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 1.013960] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 1.027080] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 1.040928] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x201fffff] [ 1.054427] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] [ 1.067938] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff] [ 1.081434] pci 0000:01:00.1: BAR 0: assigned [mem 0x20100000-0x201fffff] [ 1.094932] pci 0000:00:00.0: PCI bridge to [bus 01] [ 1.104782] pci 0000:00:00.0: bridge window [mem 0x20000000-0x201fffff] [ 1.118834] clocksource: Switched to clocksource systick [ 1.131140] NET: Registered PF_INET protocol family [ 1.141049] IP idents hash table entries: 2048 (order: 2, 16384 bytes, linear) [ 1.156563] tcp_listen_portaddr_hash hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 1.173339] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear) [ 1.188662] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 1.203899] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 1.217918] TCP: Hash tables configured (established 1024 bind 1024) [ 1.230743] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.243682] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 1.257984] NET: Registered PF_UNIX/PF_LOCAL protocol family [ 1.269287] PCI: CLS 0 bytes, default 32 [ 1.277183] rt-timer 10000100.timer: maximum frequency is 1220Hz [ 1.294239] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 1.314534] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 1.326089] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 1.347303] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252) [ 1.364977] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled [ 1.381308] printk: console [ttyS0] disabled [ 1.389832] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103 [ 1.409481] printk: console [ttyS0] enabled [ 1.409481] printk: console [ttyS0] enabled [ 1.426056] printk: bootconsole [early0] disabled [ 1.426056] printk: bootconsole [early0] disabled [ 1.465178] spi spi0.0: force spi mode3 [ 1.474323] spi-nor spi0.0: w25q128 (16384 Kbytes) [ 1.484043] 6 fixed-partitions partitions found on MTD device spi0.0 [ 1.496783] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions [ 1.511415] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions [ 1.526320] Creating 6 MTD partitions on "spi0.0": [ 1.535913] 0x000000000000-0x000000030000 : "u-boot" [ 1.548657] 0x000000030000-0x000000040000 : "u-boot-env" [ 1.560881] 0x000000040000-0x000000050000 : "factory" [ 1.574525] OF: Bad cell count for /palmbus@10000000/spi@b00/flash@0/partitions [ 1.590026] 0x000000050000-0x000000070000 : "cimage" [ 1.603981] 0x000000070000-0x000000fe0000 : "firmware" [ 1.616022] 2 uimage-fw partitions found on MTD device firmware [ 1.627935] Creating 2 MTD partitions on "firmware": [ 1.637843] 0x000000000000-0x000000257baa : "kernel" [ 1.647743] mtd: partition "kernel" doesn't end on an erase/write block -- force read-only [ 1.667548] 0x000000257baa-0x000000f70000 : "rootfs" [ 1.677541] mtd: partition "rootfs" doesn't start on an erase/write block boundary -- force read-only [ 1.697218] mtd: setting mtd6 (rootfs) as root device [ 1.708626] 1 squashfs-split partitions found on MTD device rootfs [ 1.721078] 0x0000005b0000-0x000000f70000 : "rootfs_data" [ 1.734287] 0x000000fe0000-0x000001000000 : "freespace" [ 1.778741] gsw: setting port4 to ephy mode [ 1.787525] mtk_soc_eth 10100000.ethernet: mdio-bus disabled [ 1.799112] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver [ 1.811796] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 1.829100] rt2880_wdt 10000120.watchdog: Initialized [ 1.841194] NET: Registered PF_INET6 protocol family [ 1.858556] Segment Routing with IPv6 [ 1.865965] In-situ OAM (IOAM) with IPv6 [ 1.873996] NET: Registered PF_PACKET protocol family [ 1.884174] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this. [ 1.910606] 8021q: 802.1Q VLAN Support v1.8 [ 1.944477] VFS: Mounted root (squashfs filesystem) readonly on device 31:6. [ 1.965179] Freeing unused kernel image (initmem) memory: 1208K [ 1.977013] This architecture does not have kernel memory protection. [ 1.989862] Run /sbin/init as init process [ 3.424958] init: Console is alive [ 3.432558] init: - watchdog - [ 5.237045] mtk_soc_eth 10100000.ethernet eth0: port 2 link up (100Mbps/Full duplex) [ 5.943924] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 6.095343] usbcore: registered new interface driver usbfs [ 6.106449] usbcore: registered new interface driver hub [ 6.117214] usbcore: registered new device driver usb [ 6.136612] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver [ 6.153445] fsl-ehci: Freescale EHCI Host controller driver [ 6.166812] ehci-platform: EHCI generic platform driver [ 6.184141] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver [ 6.199344] ohci-platform: OHCI generic platform driver [ 6.220133] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 6.239210] init: - preinit - [ 8.869703] random: jshn: uninitialized urandom read (4 bytes read) [ 9.109327] random: jshn: uninitialized urandom read (4 bytes read) [ 9.419634] random: jshn: uninitialized urandom read (4 bytes read) [ 10.506485] 8021q: adding VLAN 0 to HW filter on device eth0 [ 10.532644] random: procd: uninitialized urandom read (4 bytes read) Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 11.745327] jffs2: notice: (351) jffs2_build_xattr_subsystem: complete building xattr subsystem, 6 of xdatum (0 unchecked, 1 orphan) and 7 of xref (1 dead, 0 orphan) found. [ 11.779690] mount_root: switching to jffs2 overlay [ 11.799221] overlayfs: upper fs does not support tmpfile. [ 11.822572] urandom-seed: Seeding with /etc/urandom.seed [ 11.979320] procd: - early - [ 11.985535] procd: - watchdog - [ 12.483941] procd: - watchdog - [ 12.490982] procd: - ubus - [ 12.698046] random: ubusd: uninitialized urandom read (4 bytes read) [ 12.714641] random: ubusd: uninitialized urandom read (4 bytes read) [ 12.727904] random: ubusd: uninitialized urandom read (4 bytes read) [ 12.749203] procd: - init - Please press Enter to activate this console. [ 13.826327] random: ubusd: uninitialized urandom read (4 bytes read) [ 13.839532] random: ubus: uninitialized urandom read (4 bytes read) [ 14.421882] random: jshn: uninitialized urandom read (4 bytes read) [ 14.961496] kmodloader: loading kernel modules from /etc/modules.d/* [ 15.726073] Loading modules backported from Linux version v6.5-0-g2dde18cd1d8f [ 15.740563] Backport generated by backports.git v5.15.92-1-56-g5fb2ccb6b9e8 [ 16.832882] PPP generic driver version 2.4.2 [ 16.853960] NET: Registered PF_PPPOX protocol family [ 16.909207] mt76x0e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4 [ 16.922010] mt76x0e 0000:01:00.0: ASIC revision: 76100002 [ 16.963526] mt76x0e 0000:01:00.0: Firmware Version: 0.1.00 [ 17.223282] mt76x0e 0000:01:00.0: EEPROM ver:01 fae:00 [ 17.234238] mt76x0e 0000:01:00.0: registering led 'mt76-phy0' [ 17.458096] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected [ 17.517591] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 7620 detected [ 17.622224] kmodloader: done loading kernel modules from /etc/modules.d/* [ 36.731727] random: crng init done [ 36.738529] random: 68 urandom warning(s) missed due to ratelimiting [ 66.815316] 8021q: adding VLAN 0 to HW filter on device eth0 [ 66.899807] br-lan: port 1(eth0.1) entered blocking state [ 66.910672] br-lan: port 1(eth0.1) entered disabled state [ 66.921888] device eth0.1 entered promiscuous mode [ 66.931449] device eth0 entered promiscuous mode [ 67.121911] br-lan: port 1(eth0.1) entered blocking state [ 67.132744] br-lan: port 1(eth0.1) entered forwarding state [ 67.852187] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 156.104261] urngd: v1.0.2 started.


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/01/25 00:25
  • by phoebe