COMFAST CF-E538AC

Comfast CF-E538AC is a wall mounted access point powered exclusively via PoE. It has 2 Gigabit Ethernet ports and supports 802.11AC Wave2 MU-MIMO.

Comfast CF-E538AC front Comfast CF-E538AC back

Not supported.

Describe if there are any ongoing activities that might lead to OpenWrt support.

CPU Ram Flash Network WLAN USB Serial JTag
MediaTek MT7620DA @ 580 MHz 64 MiB 8 MiB 2x 10/100/1000 bgn/ac x Yes ?
Architecture MIPS
Vendor Ralink
Bootloader U-Boot
System-On-Chip MediaTek MT7620DA
CPU/Speed 580 MHz
Flash-Chip Winbond 25064JVS10
Flash size 8 MiB
RAM 64 MiB
Wireless MT7612E 5GHz 802.11ac-MT7620DA 2.4Ghz bgn
Ethernet 2x Gbit w/ vlan support
Switch Built-in SoC MediaTek MT7620DA
USB none
Serial 115200 8N1 (solder 4 pins) 3.3V
JTAG unknown

Comfast CF-E538AC - Front Comfast CF-E538AC - Back Top PCB front Top PCB back Bottom PCB front Bottom PCB back Flash Chip Windbond 25064 5Ghz Wireless Chip Mediatek MT7612EN Ethernet transceiver Realtek RTL8211F

The top case simply clips in with 2 clips per side (so 8 clips in total). Insert several thin sturdy devices (e.g. knives) to lift the clips away from the case until you can remove the top cover.

The device consists of 2 PCBs. The top and bottom PCBs are simply held in place and connected by 2×12 pins. Gently pull on the top PCB to remove it from the bottom PCB.

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Markings for the Serial Port can be found on the back-side of the top PCB (top left corner of this photo) Serial connector

As marked on the PCB (from left to right): RX | TX | GND | VCC The square marks PIN1 (VCC)

Alternative view from the top:

Serial connection parameters
for COMFAST CF-E538AC
115200, 8N1, 3.3V

port.jtag general information about the JTAG port, JTAG cable, etc.

Unknown

U-Boot 1.1.3 (May 25 2019 - 17:08:41) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fb0000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. spi_wait_nsec: 29 spi device id: ef 40 17 0 0 (40170000) find flash: W25Q64BV raspi_read: from:30000 len:1000 raspi_read: from:30000 len:1000 ============================================ Ralink UBoot Version: 4.3.0.0 -------------------------------------------- ASIC 7620_MP (Port5<->Phy) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:May 25 2019 Time:17:08:41 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes raspi_read: from:40028 len:6 netboot_common, argc= 3 NetTxPacket = 0x83FE5000 KSEG1ADDR(NetTxPacket) = 0xA3FE5000 NetLoop,call eth_halt ! NetLoop,call eth_init ! Trying Eth0 (10/100-M) Waitting for RX_DMA_BUSY status Start... done Using Eth0 (10/100-M) device TFTP from server 192.168.1.10; our IP address is 192.168.1.1 TIMEOUT_COUNT=10,Load address: 0x80800000 Loading: *T T Please Input new ones /or Ctrl-C to discard Input device IP (192.168.1.1) Input server IP (192.168.1.10) Input Linux Kernel filename () netboot_common, argc= 3 KSEG1ADDR(NetTxPacket) = 0xA3FE5000 NetLoop,call eth_halt ! NetLoop,call eth_init ! Trying Eth0 (10/100-M) Using Eth0 (10/100-M) device TFTP from server 192.168.1.10; our IP address is 192.168.1.1 TIMEOUT_COUNT=10,Load address: 0x80100000 Loading: *T T raspi_erase_write: offs:50000, count:0 Done! Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. default: 3  0 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 Image Name: MIPS OpenWrt Linux-3.18.9 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1231356 Bytes = 1.2 MB Load Address: 80000000 Entry Point: 80000000 raspi_read: from:50040 len:12c9fc Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... [ 0.000000] Linux version 3.18.9 (malinan@oracle.tecmint.com) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 Thu Sep 12 15:51:50 CST 2019 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: Ralink MT7620A ver:2 eco:6 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is Comfast CF-E538AC [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Initmem setup node 0 [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=0006f81b [ 0.000000] Readback ErrCtl register=0006f81b [ 0.000000] Memory: 61028K/65536K available (2688K kernel code, 156K rwdata, 604K rodata, 192K init, 194K bss, 4508K reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:256 [ 0.000000] CPU Clock: 580MHz [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.000000] genirq: Flags mismatch irq 7. 00014600 (timer) vs. 00014600 (systick) [ 0.000000] Calibrating delay loop... 766.77 BogoMIPS (lpj=3833856) [ 0.040000] pid_max: default: 32768 minimum: 301 [ 0.040000] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.040000] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) [ 0.050000] pinctrl core: initialized pinctrl subsystem [ 0.050000] NET: Registered protocol family 16 [ 0.310000] PCI host bridge /pcie@10140000 ranges: [ 0.310000] MEM 0x0000000020000000..0x000000002fffffff [ 0.310000] IO 0x0000000010160000..0x000000001016ffff [ 0.320000] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.320000] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.330000] rt2880_gpio 10000660.gpio: registering 32 gpios [ 0.330000] rt2880_gpio 10000660.gpio: registering 32 irq handlers [ 0.330000] rt2880_gpio 10000688.gpio: registering 1 gpios [ 0.330000] rt2880_gpio 10000688.gpio: registering 1 irq handlers [ 0.340000] PCI host bridge to bus 0000:00 [ 0.340000] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] [ 0.340000] pci_bus 0000:00: root bus resource [io 0xffffffff] [ 0.340000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.350000] pci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguring [ 0.350000] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 0.350000] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 0.360000] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff] [ 0.360000] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref] [ 0.360000] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] [ 0.370000] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit] [ 0.370000] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref] [ 0.370000] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.370000] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff] [ 0.380000] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref] [ 0.380000] pci 0000:00:00.0: card - bus=0x0, slot = 0x0 irq=0 [ 0.380000] pci 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4 [ 0.380000] Switched to clocksourcestick [ 0.390000] NET: Registered protocol family 2 [ 0.390000] TCP established hash table entries: 1024 (order: 0, 4096 bytes) [ 0.400000] TCP bind hash table entries: 1024 (order: 0, 4096 bytes) [ 0.400000] TCP: Hash tables configured (established 1024 bind 1024) [ 0.410000] TCP: reno registered [ 0.410000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.420000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.430000] NET: Registered protocol family 1 [ 0.430000] rt-timer 10000100.timer: maximum frequency is 2441Hz [ 0.430000] futex hash table entries: 256 (order: -1, 3072 bytes) [ 0.470000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.470000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.470000] msgmni has been set to 119 [ 0.490000] io scheduler noop registered [ 0.490000] io scheduler deadline registered (default) [ 0.490000] drivers/phy/phy-ralink-usb.c:ralink_usb_phy_probe[147] [ 0.490000] drivers/phy/phy-ralink-usb.c:ralink_usb_phy_probe[161] [ 0.510000] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.510000] console [ttyS0] disabled [ 0.510000] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a 16550A [ 0.530000] console [ttyS0] enabled [ 0.530000] console [ttyS0] enabled [ 0.530000] bootconsole [early0] disabled [ 0.530000] bootconsole [early0] disabled [ 0.550000] m25p80 spi32766.0: found s25fl064k, expected en25q64 [ 0.550000] m25p80 spi32766.0: s25fl064k (8192 Kbytes) [ 0.550000] 6 ofpart partitions found on MTD device spi32766.0 [ 0.570000] Creating 6 MTD partitions on "spi32766.0": [ 0.570000] 0x000000000000-0x000000030000 : "u-boot" [ 0.570000] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.580000] 0x000000040000-0x000000050000 : "factory" [ 0.580000] 0x000000050000-0x0000007c0000 : "firmware" [ 0.580000] 2 uimage-fw partitions found on MTD device firmware [ 0.580000] 0x000000050000-0x00000017ca3c : "kernel" [ 0.580000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.580000] 0x00000017ca3c-0x0000007c0000 : "rootfs" [ 0.580000] mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only [ 0.580000] mtd: device 5 (rootfs) set to be root filesystem [ 0.580000] 1 squashfs-split partitions found on MTD device rootfs [ 0.580000] 0x000000630000-0x0000007c0000 : "rootfs_data" [ 0.580000] 0x0000007c0000-0x000000800000 : "configs" [ 0.580000] 0x000000800000-0x000001000000 : "reserve" [ 0.580000] mtd: partition "reserve" is out of reach -- disabled [ 0.580000] libphy: mdio: probed [ 0.580000] ralink_soc_eth 10100000.ethernet: connected port 4 to PHY at mdio-bus:04 [uid=001cc916, driver=Generic PHY] [ 0.580000] ralink_soc_eth 10100000.ethernet: connected port 5 to PHY at mdio-bus:05 [uid=001cc916, driver=Generic PHY] [ 0.580000] ralink_soc_eth 10100000.ethernet: loaded mt7620 driver [ 0.580000] ralink_soc_eth 10100000.ethernet eth0: ralink at 0xb0100000, irq 5 [ 0.580000] rt2880_wdt 10000120.watchdog: Initialized [ 0.580000] TCP: cubic registered [ 0.580000] NET: Registered protocol family 17 [ 0.580000] bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. [ 0.580000] Bridge firewalling registered [ 0.580000] 8021q: 802.1Q VLAN Support v1.8 [ 0.580000] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 0.580000] Freeing unused kernel memory: 192K (80360000 - 80390000) [ 3.200000] init: Console is alive [ 3.200000] init: - watchdog - [ 6.280000] init: - preinit - [ 7.500000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 7.550000] random: mktemp urandom read with 8 bits of entropy available Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 10.450000] jffs2: notice: (390) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (1 unchecked, 0 orphan) and 1 of xref (0 dead, 0 orphan) found. [ 10.480000] mount_root: switching to jffs2 overlay [ 10.520000] procd: - early - [ 10.520000] procd: - watchdog - [ 11.380000] procd: - ubus - [ 12.700000] procd: - init - Please press Enter to activate this console. [ 14.480000] gre: GRE over IPv4 demultiplexor driver [ 14.480000] ip_gre: GRE over IPv4 tunneling driver [ 14.490000] i2c /dev entries driver [ 14.500000] u32 classifier [ 14.510000] input device check on [ 14.510000] Actions configured [ 14.520000] Mirror/redirect action on [ 14.530000] nf_conntrack version 0.5.0 (956 buckets, 3824 max) [ 14.600000] Ebtables v2.0 registered [ 14.610000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 14.690000] Netfilter messages via NETLINK v0.30. [ 14.730000] xt_time: kernel timezone is -0000 [ 14.750000] ctnetlink v0.93: registering with nfnetlink. [ 14.770000] PPP generic driver version 2.4.2 [ 14.790000] PPP MPPE Compression module registered [ 14.790000] NET: Registered protocol family 24 [ 20.910000] 8021q: adding VLAN 0 to HW filter on device eth0 [ 20.930000] ralink_soc_eth 10100000.ethernet eth0: port 4 link up (100Mbps/Full duplex) [ 20.930000] ralink_soc_eth 10100000.ethernet eth0: port 5 link up (100Mbps/Full duplex) [ 20.970000] device eth0.1 entered promiscuous mode [ 20.970000] device eth0 entered promiscuous mode [ 20.970000] br-lan: port 1(eth0.1) entered forwarding state [ 20.990000] br-lan: port 1(eth0.1) entered forwarding state [ 21.030000] device eth0.2 entered promiscuous mode [ 21.030000] br-wan: port 1(eth0.2) entered forwarding state [ 21.050000] br-wan: port 1(eth0.2) entered forwarding state [ 23.180000] br-lan: port 1(eth0.1) entered forwarding state [ 23.190000] br-wan: port 1(eth0.2) entered forwarding state configs:do check configs [ 34.650000] register rt2860 [ 34.650000] [ 34.650000] [ 34.650000] === pAd = c0781000, size = 2104016 === [ 34.650000] [ 34.650000] <-- RTMPAllocTxRxRingMemory, Status=0 [ 34.650000] <-- RTMPAllocAdapterBlock, Status=0 [ 34.650000] pAd->CSRBaseAddress =0xc0680000, csr_addr=0xc0680000! [ 34.650000] device_id =0x7662 [ 34.650000] ==>rlt_wlan_chip_onoff(): OnOff:1, Reset= 1, pAd->WlanFunCtrl:0x0, Reg-WlanFunCtrl=0x20a [ 34.650000] chip_id1=, chip_id2=7612, pAd->MACVersion=0x76623000 [ 34.650000] chip_id1=0x0, chip_id2=0x7612, pAd->MACVersion=0x76623000 [ 34.650000] RtmpChipOpsEepromHook::e2p_type=0, inf_Type=5 [ 34.650000] RtmpEepromGetDefault::e2p_dafault=2 [ 34.650000] NVM is efuse and the information is too less to bring up the interface [ 34.650000] Force to use Flash mode [ 34.650000] NVM is FLASH mode (pAd->flash_offset = 0x48000) [ 34.650000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai [ 35.060000] build time = [ 35.070000] 20141115060606a [ 35.070000] rom patch for E3 IC [ 35.070000] [ 35.070000] platform = [ 35.070000] ALPS [ 35.070000] hw/sw version = [ 35.080000] ŠŠ [ 35.080000] patch version = [ 35.090000]  [ 35.110000] FW Version:0.0.00 Build:1 [ 35.110000] Build Time:201607111443____ [ 35.110000] fw for E3 IC [ 35.360000] RX[0] DESC a1c04000 size = 4096 [ 35.360000] RX[1] DESC a1c05000 size = 4096 [ 35.400000] E2pAccessMode=2 [ 35.400000] cfg_mode=14 [ 35.400000] cfg_mode=14 [ 35.400000] wmode_band_equal(): Band Not Equal! [ 35.420000] APSDCapable[0]=0 [ 35.420000] APSDCapable[1]=0 [ 35.420000] APSDCapable[2]=0 [ 35.420000] APSDCapable[3]=0 [ 35.420000] APSDCapable[4]=0 [ 35.420000] APSDCapable[5]=0 [ 35.420000] APSDCapable[6]=0 [ 35.440000] APSDCapable[7]=0 [ 35.440000] APSDCapable[8]=0 [ 35.440000] APSDCapable[9]=0 [ 35.440000] APSDCapable[10]=0 [ 35.440000] APSDCapable[11]=0 [ 35.440000] APSDCapable[12]=0 [ 35.450000] APSDCapable[13]=0 [ 35.460000] APSDCapable[14]=0 [ 35.460000] APSDCapable[15]=0 [ 35.460000] default ApCliAPSDCapable[0]=0 [ 35.660000] Key1Str is Invalid key length(0) or Type(1) [ 35.670000] Key1Str is Invalid key length(0) or Type(1) [ 35.670000] Key1Str is Invalid key length(0) or Type(1) [ 35.670000] Key1Str is Invalid key length(0) or Type(1) [ 35.690000] Key1Str is Invalid key length(0) or Type(1) [ 35.690000] Key1Str is Invalid key length(0) or Type(1) [ 35.690000] Key1Str is Invalid key length(0) or Type(1) [ 35.690000] Key1Str is Invalid key length(0) or Type(1) [ 35.710000] Key2Str is Invalid key length(0) or Type(1) [ 35.710000] Key2Str is Invalid key length(0) or Type(1) [ 35.710000] Key2Str is Invalid key length(0) or Type(1) [ 35.720000] Key2Str is Invalid key length(0) or Type(1) [ 35.730000] Key2Str is Invalid key length(0) or Type(1) [ 35.730000] Key2Str is Invalid key length(0) or Type(1) [ 35.740000] Key2Str is Invalid key length(0) or Type(1) [ 35.740000] Key2Str is Invalid key length(0) or Type(1) [ 35.750000] Key3Str is Invalid key length(0) or Type(1) [ 35.760000] Key3Str is Invalid key length(0) or Type(1) [ 35.760000] Key3Str is Invalid key length(0) or Type(1) [ 35.760000] Key3Str is Invalid key length(0) or Type(1) [ 35.770000] Key3Str is Invalid key length(0) or Type(1) [ 35.780000] Key3Str is Invalid key length(0) or Type(1) [ 35.780000] Key3Str is Invalid key length(0) or Type(1) [ 35.790000] Key3Str is Invalid key length(0) or Type(1) [ 35.790000] Key4Str is Invalid key length(0) or Type(1) [ 35.800000] Key4Str is Invalid key length(0) or Type(1) [ 35.810000] Key4Str is Invalid key length(0) or Type(1) [ 35.810000] Key4Str is Invalid key length(0) or Type(1) [ 35.810000] Key4Str is Invalid key length(0) or Type(1) [ 35.830000] Key4Str is Invalid key length(0) or Type(1) [ 35.830000] Key4Str is Invalid key length(0) or Type(1) [ 35.830000] Key4Str is Invalid key length(0) or Type(1) [ 35.890000] 1. Phy Mode = 49 [ 35.890000] get_chl_grp:illegal channel (167) [ 35.910000] get_chl_grp:illegal channel (167) [ 35.910000] get_chl_grp:illegal channel (169) [ 35.910000] get_chl_grp:illegal channel (169) [ 35.910000] get_chl_grp:illegal channel (171) [ 35.920000] get_chl_grp:illegal channel (171) [ 35.930000] /home/malinan/work/new/OPENWRT/trunk/build_dir/target-mipsel_24kec+dsp_uClibc-0.9.33.2/linux-ramips_mt7620/mt76x2e-3.0.4.0/rlt_wifi_ap/../rlt_wifi/chips/mt76x2.c:2899 assert (ad->TxPower[choffset].Channel == 42)failed [ 35.950000] Country Region from e2p = ffff [ 35.950000] mt76x2_read_temp_info_from_eeprom:: is_temp_tx_alc=0, temp_tx_alc_enable=0 [ 35.960000] mt76x2_read_tx_alc_info_from_eeprom:: is_ePA_mode=0, ePA_type=3 [ 35.970000] mt76x2_read_tx_alc_info_from_eeprom:: [5G band] high_temp_slope=0, low_temp_slope=0 [ 35.970000] mt76x2_read_tx_alc_info_from_eeprom:: [2G band] high_temp_slope=0, low_temp_slope=0 [ 35.970000] mt76x2_read_tx_alc_info_from_eeprom:: [5G band] tc_lower_bound=0, tc_upper_bound=0 [ 35.970000] mt76x2_read_tx_alc_info_from_eeprom:: [2G band] tc_lower_bound=0, tc_upper_bound=0 [ 35.970000] mt76x2_get_external_lna_gain::LNA type=0x11, BLNAGain=0x0, ALNAGain0=0x0, ALNAGain1=0x0, ALNAGain2=0x0 [ 35.970000] 2. Phy Mode = 49 [ 35.970000] 3. Phy Mode = 49 [ 35.970000] andes_pci_fw_init [ 35.970000] 0x1300 = 00073200 [ 35.970000] AntCfgInit: primary/secondary ant 0/1 [ 35.970000] andes_load_cr:cr_type(2) [ 35.970000] ChipStructAssign(): MT76x2 hook ! [ 35.970000] @@@ BuildChannel # 36 :: Pwr0 = 30, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 @@@ BuildChannel # 40 :: Pwr0 = 30, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 @@@ BuildChannel # 44 :: Pwr0 = 30, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 @@@ BuildChannel # 48 :: Pwr0 = 30, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 @@@ BuildChannel # 52 :: Pwr0 = 30, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 @@@ BuildChannel # 56 :: Pwr0 = 30, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 @@@ BuildChannel # 60 :: Pwr0 = 30, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 @@@ BuildChannel # 64 :: Pwr0 = 30, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 @@@ BuildChannel # 149 :: Pwr0 = 30, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 @@@ BuildChannel # 153 :: Pwr0 = 30, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 @@@ BuildChannel # 157 :: Pwr0 = 30, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 @@@ BuildChannel # 161 :: Pwr0 = 30, Pwr1 =30, Flags = c0, RemainingTimeForUse=0 @@@ BuildChannel # 165 :: Pwr0 = 30, Pwr1 =30, Flags = 0, RemainingTimeForUse=0 RTMPSetPhyMode: channel is out of range, use first channel=36 [ 35.970000] MCS Set = ff ff 00 00 01 [ 36.360000] TX0 power compensation = 0x38 [ 36.380000] TX1 power compensation = 0x38 COMFAST login: [ 41.770000] mt76x2_bbp_adjust():rf_bw=2, ext_ch=3, PrimCh=56, HT-CentCh=54, VHT-CentCh=58 [ 41.890000] APStartUp(): AP Set CentralFreq at 58(Prim=56, HT-CentCh=54, VHT-CentCh=58, BBP_BW=2) [ 41.930000] mt76x2_calibration(channel = 58) [ 42.360000] Main bssid = 20:0d:b0:75:3a:9e [ 42.370000] mt76x2_reinit_agc_gain:original agc_vga0 = 0x5c, agc_vga1 = 0x5c [ 42.370000] mt76x2_reinit_agc_gain:updated agc_vga0 = 0x5c, agc_vga1 = 0x5c [ 42.380000] mt76x2_reinit_hi_lna_gain:original hi_lna0 = 0x27, hi_lna1 = 0x27 [ 42.390000] mt76x2_reinit_hi_lna_gain:updated hi_lna0 = 0x27, hi_lna1 = 0x27 [ 42.390000] original vga value(chain0) = 5c [ 42.400000] original vga value(chain1) = 5c [ 42.400000] <==== rt28xx_init, Status=0 [ 42.410000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai root[ 42.410000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai [ 42.450000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai BusyBox v1.26.2 () built-in shell (ash) root@COMFAST:~# [ 42.520000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai [ 42.520000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai [ 42.520000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai [ 42.520000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=rai [ 42.520000] get_dev_name_prefix(): dev_idx = 1, dev_name_prefix=apclii [ 42.520000] RTMPDrvOpen(1):Check if PDMA is idle! [ 42.520000] RTMPDrvOpen(2):Check if PDMA is idle! [ 43.200000] device rai0 entered promiscuous mode [ 43.200000] br-lan: port 2(rai0) entered forwarding state [ 43.210000] br-lan: port 2(rai0) entered forwarding state [ 43.650000] device rai7 entered promiscuous mode [ 45.460000] br-lan: port 2(rai0) entered forwarding state [ 46.270000] [ 46.270000] [ 46.270000] === pAd = c0b5e000, size = 872656 === [ 46.270000] [ 46.270000] <-- RTMPAllocTxRxRingMemory, Status=0 [ 46.280000] <-- RTMPAllocAdapterBlock, Status=0 [ 46.290000] AP Driver version-2.7.1.6 [ 46.300000] RX DESC a1b07000 size = 2048 [ 46.320000] RTMP_TimerListAdd: add timer obj c0bf5388! [ 46.320000] RTMP_TimerListAdd: add timer obj c0bbed50! [ 46.320000] RTMP_TimerListAdd: add timer obj c0bc15ac! [ 46.330000] RTMP_TimerListAdd: add timer obj c0bc166c! [ 46.340000] RTMP_TimerListAdd: add timer obj c0bc172c! [ 46.340000] RTMP_TimerListAdd: add timer obj c0bc17ec! [ 46.340000] RTMP_TimerListAdd: add timer obj c0bc18ac! [ 46.350000] RTMP_TimerListAdd: add timer obj c0bc196c! [ 46.360000] RTMP_TimerListAdd: add timer obj c0bc1a2c! [ 46.360000] RTMP_TimerListAdd: add timer obj c0bc1aec! [ 46.370000] RTMP_TimerListAdd: add timer obj c0bc1bac! [ 46.370000] RTMP_TimerListAdd: add timer obj c0bc1c6c! [ 46.380000] RTMP_TimerListAdd: add timer obj c0bc1d2c! [ 46.380000] RTMP_TimerListAdd: add timer obj c0bc1dec! [ 46.390000] RTMP_TimerListAdd: add timer obj c0bc1eac! [ 46.390000] RTMP_TimerListAdd: add timer obj c0bc1f6c! [ 46.400000] RTMP_TimerListAdd: add timer obj c0bc202c! [ 46.400000] RTMP_TimerListAdd: add timer obj c0bc20ec! [ 46.410000] RTMP_TimerListAdd: add timer obj c0bbed24! [ 46.420000] RTMP_TimerListAdd: add timer obj c0bbed7c! [ 46.420000] RTMP_TimerListAdd: add timer obj c0bc1580! [ 46.420000] RTMP_TimerListAdd: add timer obj c0bc1640! [ 46.430000] RTMP_TimerListAdd: add timer obj c0bc1700! [ 46.440000] RTMP_TimerListAdd: add timer obj c0bc17c0! [ 46.440000] RTMP_TimerListAdd: add timer obj c0bc1880! [ 46.440000] RTMP_TimerListAdd: add timer obj c0bc1940! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1a00! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1ac0! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1b80! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1c40! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1d00! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1dc0! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1e80! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1f40! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc2000! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc20c0! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bbecf8! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc15d8! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1698! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1758! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1818! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc18d8! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1998! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1a58! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1b18! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1bd8! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1c98! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1d58! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1e18! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1ed8! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc1f98! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc2058! [ 46.450000] RTMP_TimerListAdd: add timer obj c0bc2118! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b66044! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b65c38! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b66014! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b66350! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b66290! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b662c0! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b69258! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b68e4c! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b69228! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b69564! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b694a4! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b694d4! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b6c46c! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b6c060! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b6c43c! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b6c778! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b6c6b8! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b6c6e8! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b6f680! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b6f274! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b6f650! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b6f98c! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b6f8cc! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b6f8fc! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b72894! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b72488! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b72864! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b72ba0! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b72ae0! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b72b10! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b75aa8! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b7569c! [ 46.450000] RTMP_TimerListAdd: add timer obj c0b75a78! [ 46.770000] RTMP_TimerListAdd: add timer obj c0b75db4! [ 46.770000] RTMP_TimerListAdd: add timer obj c0b75cf4! [ 46.770000] RTMP_TimerListAdd: add timer obj c0b75d24! [ 46.790000] RTMP_TimerListAdd: add timer obj c0b78cbc! [ 46.790000] RTMP_TimerListAdd: add timer obj c0b788b0! [ 46.790000] RTMP_TimerListAdd: add timer obj c0b78c8c! [ 46.790000] RTMP_TimerListAdd: add timer obj c0b78fc8! [ 46.810000] RTMP_TimerListAdd: add timer obj c0b78f08! [ 46.810000] RTMP_TimerListAdd: add timer obj c0b78f38! [ 46.810000] RTMP_TimerListAdd: add timer obj c0b7bed0! [ 46.810000] RTMP_TimerListAdd: add timer obj c0b7bac4! [ 46.830000] RTMP_TimerListAdd: add timer obj c0b7bea0! [ 46.830000] RTMP_TimerListAdd: add timer obj c0b7c1dc! [ 46.830000] RTMP_TimerListAdd: add timer obj c0b7c11c! [ 46.840000] RTMP_TimerListAdd: add timer obj c0b7c14c! [ 46.850000] RTMP_TimerListAdd: add timer obj c0bc11cc! [ 46.850000] RTMP_TimerListAdd: add timer obj c0bc0dc0! [ 46.850000] RTMP_TimerListAdd: add timer obj c0bc119c! [ 46.860000] RTMP_TimerListAdd: add timer obj c0bc14d8! [ 46.870000] RTMP_TimerListAdd: add timer obj c0bc11fc! [ 46.870000] RTMP_TimerListAdd: add timer obj c0bc122c! [ 46.870000] RTMP_TimerListAdd: add timer obj c0bc125c! [ 46.890000] RTMP_TimerListAdd: add timer obj c0bcbcf4! [ 46.890000] RTMP_TimerListAdd: add timer obj c0bcbe10! [ 46.890000] RTMP_TimerListAdd: add timer obj c0bcbd20! [ 46.900000] RTMP_TimerListAdd: add timer obj c0bc329c! [ 46.900000] RTMP_TimerListAdd: add timer obj c0b63504! [ 46.910000] RTMP_TimerListAdd: add timer obj c0b66718! [ 46.920000] RTMP_TimerListAdd: add timer obj c0b6992c! [ 46.920000] RTMP_TimerListAdd: add timer obj c0b6cb40! [ 46.920000] RTMP_TimerListAdd: add timer obj c0b6fd54! [ 46.930000] RTMP_TimerListAdd: add timer obj c0b72f68! [ 46.940000] RTMP_TimerListAdd: add timer obj c0b7617c! [ 46.940000] RTMP_TimerListAdd: add timer obj c0b79390! [ 46.940000] RTMP_TimerListAdd: add timer obj c0bc2fa8! [ 47.220000] APSDCapable[0]=1 [ 47.220000] APSDCapable[1]=1 [ 47.220000] APSDCapable[2]=1 [ 47.220000] APSDCapable[3]=1 [ 47.220000] APSDCapable[4]=1 [ 47.220000] APSDCapable[5]=1 [ 47.240000] APSDCapable[6]=1 [ 47.240000] APSDCapable[7]=1 [ 47.240000] APSDCapable[8]=1 [ 47.240000] APSDCapable[9]=1 [ 47.240000] APSDCapable[10]=1 [ 47.240000] APSDCapable[11]=1 [ 47.240000] APSDCapable[12]=1 [ 47.260000] APSDCapable[13]=1 [ 47.260000] APSDCapable[14]=1 [ 47.260000] APSDCapable[15]=1 [ 47.260000] default ApCliAPSDCapable[0]=1 [ 47.460000] Key1Str is Invalid key length(0) or Type(1) [ 47.460000] Key1Str is Invalid key length(0) or Type(1) [ 47.470000] Key1Str is Invalid key length(0) or Type(1) [ 47.480000] Key1Str is Invalid key length(0) or Type(1) [ 47.480000] Key2Str is Invalid key length(0) or Type(1) [ 47.490000] Key2Str is Invalid key length(0) or Type(1) [ 47.500000] Key2Str is Invalid key length(0) or Type(1) [ 47.500000] Key2Str is Invalid key length(0) or Type(1) [ 47.500000] Key3Str is Invalid key length(0) or Type(1) [ 47.520000] Key3Str is Invalid key length(0) or Type(1) [ 47.520000] Key3Str is Invalid key length(0) or Type(1) [ 47.520000] Key3Str is Invalid key length(0) or Type(1) [ 47.520000] Key4Str is Invalid key length(0) or Type(1) [ 47.540000] Key4Str is Invalid key length(0) or Type(1) [ 47.540000] Key4Str is Invalid key length(0) or Type(1) [ 47.540000] Key4Str is Invalid key length(0) or Type(1) [ 47.580000] RTMPSetDefaultChannel() : default channel to 1 [ 47.580000] 1. Phy Mode = 9 [ 47.600000] 2. Phy Mode = 9 [ 47.600000] E2PROM: D0 target power=0xff20 [ 47.600000] E2PROM: 40 MW Power Delta= 0 [ 47.600000] 3. Phy Mode = 9 [ 47.600000] AntCfgInit: primary/secondary ant 0/1 Initialize RF Central Registers for E2 !!! [ 47.620000] Initialize RF Central Registers for E3 !!! [ 47.620000] Initialize RF Channel Registers for E2 !!! [ 47.620000] Initialize RF Channel Registers for E3 !!! [ 47.640000] Initialize RF DCCal Registers for E2 !!! [ 47.640000] Initialize RF DCCal Registers for E3 !!! [ 47.640000] D1 = 2, D2 = 10, CalCode = 19 !!! [ 47.660000] RT6352_Temperature_Init : BBPR49 = 0x2 [ 47.660000] RT6352_Temperature_Init : TemperatureRef25C = 0xfffffff8 [ 47.660000] Current Temperature from BBP_R49=0x1 [ 47.680000] TX BW Filter Calibration !!! [ 47.760000] RX BW Filter Calibration !!! [ 48.210000] LOFT Calibration Done! [ 48.210000] IQCalibration Start! [ 48.230000] IQCalibration Done! CH = 0, (gain= 0, phase= 2) [ 48.230000] IQCalibration Start! [ 48.250000] IQCalibration Done! CH = 1, (gain= 0, phase= 2) [ 48.250000] TX IQ Calibration Done! [ 48.330000] RXIQ si=2103, sq=1970, riq=47, bbpval 2103, vga_idx 0 [ 48.330000] RXIQ si=4743, sq=4471, riq=118, bbpval 4743, vga_idx 2 [ 48.330000] RXIQ si=7546, sq=7111, riq=188, bbpval 7546, vga_idx 3 [ 48.350000] RXIQ si=11702, sq=11023, riq=316, bbpval 11702, vga_idx 4 [ 48.350000] Sigma_i=1081, Sigma_q=1049, R_iq=3160 [ 48.350000] RXIQ Sigma_i=1081, Sigma_q=1049, R_iq=3160 [ 48.350000] RXIQ G_imb=-3, Ph_rx=6 [ 48.370000] RXIQ si=405, sq=397, riq=0, bbpval 405, vga_idx 0 [ 48.370000] RXIQ si=3531, sq=3475, riq=23, bbpval 3531, vga_idx 5 [ 48.370000] RXIQ si=5581, sq=5496, riq=54, bbpval 5581, vga_idx 6 [ 48.390000] RXIQ si=8646, sq=8504, riq=48, bbpval 8646, vga_idx 7 [ 48.390000] RXIQ si=13239, sq=13036, riq=92, bbpval 13239, vga_idx 8 [ 48.390000] Sigma_i=1150, Sigma_q=1141, R_iq=920 [ 48.400000] RXIQ Sigma_i=1150, Sigma_q=1141, R_iq=920 [ 48.410000] RXIQ G_imb=-1, Ph_rx=1 [ 48.410000] MCS Set = ff ff 00 00 01 [ 48.480000] SYNC - BBP R4 to 20MHz.l [ 52.130000] RTMP_TimerListAdd: add timer obj c0bc3584! [ 52.330000] br-wan: received packet on eth0.2 with own address as source address [ 52.400000] Main bssid = 20:0d:b0:75:3a:9d [ 52.410000] <==== rt28xx_init, Status=0 [ 52.440000] 0x1300 = 00064320 [ 52.450000] br-wan: received packet on eth0.2 with own address as source address [ 53.000000] device ra0 entered promiscuous mode [ 53.000000] br-lan: adding interface ra0 with same address as a received packet [ 53.000000] br-lan: port 4(ra0) entered forwarding state [ 53.000000] br-lan: port 4(ra0) entered forwarding state [ 53.450000] br-wan: received packet on eth0.2 with own address as source address [ 53.640000] device ra7 entered promiscuous mode [ 54.640000] br-wan: received packet on eth0.2 with own address as source address [ 54.640000] br-lan: received packet on eth0.1 with own address as source address [ 55.000000] br-lan: port 4(ra0) entered forwarding state [ 57.680000] br-lan: received packet on eth0.1 with own address as source address [ 61.190000] ralink_soc_eth 10100000.ethernet eth0: port 5 link down


U-Boot 1.1.3 (May 25 2019 - 17:08:41) Board: Ralink APSoC DRAM: 64 MB relocate_code Pointer at: 83fb0000 enable ephy clock...done. rf reg 29 = 5 SSC disabled. ****************************** Software System Reset Occurred ****************************** spi_wait_nsec: 29 spi device id: ef 40 17 0 0 (40170000) find flash: W25Q64BV raspi_read: from:30000 len:1000 *** Warning - bad CRC, using default environment ============================================ Ralink UBoot Version: 4.3.0.0 -------------------------------------------- ASIC 7620_MP (Port5<->Phy) DRAM component: 512 Mbits DDR, width 16 DRAM bus: 16 bit Total memory: 64 MBytes Flash component: SPI Flash Date:May 25 2019 Time:17:08:41 ============================================ icache: sets:512, ways:4, linesz:32 ,total:65536 dcache: sets:256, ways:4, linesz:32 ,total:32768 ##### The CPU freq = 580 MHZ #### estimate memory size =64 Mbytes raspi_read: from:40028 len:6 netboot_common, argc= 3 NetTxPacket = 0x83FE5000 KSEG1ADDR(NetTxPacket) = 0xA3FE5000 NetLoop,call eth_halt ! NetLoop,call eth_init ! Trying Eth0 (10/100-M) Waitting for RX_DMA_BUSY status Start... done Using Eth0 (10/100-M) device TFTP from server 192.168.1.10; our IP address is 192.168.1.1 TIMEOUT_COUNT=10,Load address: 0x80800000 Loading: *T T Please Input new ones /or Ctrl-C to discard Input device IP (192.168.1.1) Input server IP (192.168.1.10) Input Linux Kernel filename () netboot_common, argc= 3 KSEG1ADDR(NetTxPacket) = 0xA3FE5000 NetLoop,call eth_halt ! NetLoop,call eth_init ! Trying Eth0 (10/100-M) Using Eth0 (10/100-M) device TFTP from server 192.168.1.10; our IP address is 192.168.1.1 TIMEOUT_COUNT=10,Load address: 0x80100000 Loading: *T T raspi_erase_write: offs:50000, count:0 Done! Please choose the operation: 1: Load system code to SDRAM via TFTP. 2: Load system code then write to Flash via TFTP. 3: Boot system code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. default: 3  0 3: System Boot system code via Flash. ## Booting image at bc050000 ... raspi_read: from:50000 len:40 Image Name: MIPS OpenWrt Linux-5.4.75 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 1939550 Bytes = 1.8 MB Load Address: 80000000 Entry Point: 80000000 raspi_read: from:50040 len:1d985e Verifying Checksum ... OK Uncompressing Kernel Image ... OK No initrd ## Transferring control to Linux (at address 80000000) ... ## Giving linux memsize in MB, 64 Starting kernel ... [ 0.000000] Linux version 5.4.75 (user@OpenWRT-build) (gcc version 8.4.0 (OpenWrt GCC 8.4.0 r14926-41b867165d)) #0 Thu Nov 12 17:21:55 2020 [ 0.000000] Board has DDR2 [ 0.000000] Analog PMU set to hw control [ 0.000000] Digital PMU set to hw control [ 0.000000] SoC Type: MediaTek MT7620A ver:2 eco:6 [ 0.000000] printk: bootconsole [early0] enabled [ 0.000000] CPU0 revision is: 00019650 (MIPS 24KEc) [ 0.000000] MIPS: machine is Comfast CF-E538AC [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, PIPT, no aliases, linesize 32 bytes [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Initmem setup node 0 [mem 0x0000000000000000-0x0000000003ffffff] [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 16240 [ 0.000000] Kernel command line: console=ttyS0,115200 rootfstype=squashfs,jffs2 [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes, linear) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes, linear) [ 0.000000] Writing ErrCtl register=0006fa20 [ 0.000000] Readback ErrCtl register=0006fa20 [ 0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off [ 0.000000] Memory: 57568K/65536K available (4581K kernel code, 204K rwdata, 1020K rodata, 1228K init, 205K bss, 7968K reserved, 0K cma-reserved) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS: 256 [ 0.000000] random: get_random_bytes called from start_kernel+0x32c/0x518 with crng_init=0 [ 0.000000] CPU Clock: 580MHz [ 0.000000] clocksource: systick: mask: 0xffff max_cycles: 0xffff, max_idle_ns: 583261500 ns [ 0.000000] systick: enable autosleep mode [ 0.000000] systick: running - mult: 214748, shift: 32 [ 0.000000] clocksource: MIPS: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6590553264 ns [ 0.000010] sched_clock: 32 bits at 290MHz, resolution 3ns, wraps every 7405115902ns [ 0.007591] Calibrating delay loop... 385.02 BogoMIPS (lpj=770048) [ 0.045483] pid_max: default: 32768 minimum: 301 [ 0.050172] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.057231] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.071377] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns [ 0.080858] futex hash table entries: 256 (order: -1, 3072 bytes, linear) [ 0.087553] pinctrl core: initialized pinctrl subsystem [ 0.093223] NET: Registered protocol family 16 [ 0.359510] PCI host bridge /pcie@10140000 ranges: [ 0.364127] MEM 0x0000000020000000..0x000000002fffffff [ 0.369186] IO 0x0000000010160000..0x000000001016ffff [ 0.397486] rt2880_gpio 10000600.gpio: registering 24 gpios [ 0.402965] rt2880_gpio 10000600.gpio: registering 24 irq handlers [ 0.409323] rt2880_gpio 10000688.gpio: registering 1 gpios [ 0.414672] rt2880_gpio 10000688.gpio: registering 1 irq handlers [ 0.421401] PCI host bridge to bus 0000:00 [ 0.425383] pci_bus 0000:00: root bus resource [mem 0x20000000-0x2fffffff] [ 0.432007] pci_bus 0000:00: root bus resource [io 0xffffffff] [ 0.437753] pci_bus 0000:00: root bus resource [??? 0x00000000 flags 0x0] [ 0.444343] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.452084] pci 0000:00:00.0: [1814:0801] type 01 class 0x060400 [ 0.457904] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x7fffffff] [ 0.463964] pci 0000:00:00.0: reg 0x14: [mem 0x20200000-0x2020ffff] [ 0.470124] pci 0000:00:00.0: supports D1 [ 0.473946] pci 0000:00:00.0: PME# supported from D0 D1 D3hot [ 0.481721] pci 0000:01:00.0: [14c3:7662] type 00 class 0x028000 [ 0.487603] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x000fffff 64bit] [ 0.494188] pci 0000:01:00.0: reg 0x30: [mem 0x00000000-0x0000ffff pref] [ 0.500766] pci 0000:01:00.0: PME# supported from D0 D3hot D3cold [ 0.508714] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01 [ 0.515122] pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01 [ 0.521556] pci 0000:00:00.0: BAR 0: no space for [mem size 0x80000000] [ 0.527942] pci 0000:00:00.0: BAR 0: failed to assign [mem size 0x80000000] [ 0.534701] pci 0000:00:00.0: BAR 8: assigned [mem 0x20000000-0x200fffff] [ 0.541303] pci 0000:00:00.0: BAR 9: assigned [mem 0x20100000-0x201fffff pref] [ 0.548315] pci 0000:00:00.0: BAR 1: assigned [mem 0x20200000-0x2020ffff] [ 0.554918] pci 0000:01:00.0: BAR 0: assigned [mem 0x20000000-0x200fffff 64bit] [ 0.562030] pci 0000:01:00.0: BAR 6: assigned [mem 0x20100000-0x2010ffff pref] [ 0.569021] pci 0000:00:00.0: PCI bridge to [bus 01] [ 0.573840] pci 0000:00:00.0: bridge window [mem 0x20000000-0x200fffff] [ 0.580429] pci 0000:00:00.0: bridge window [mem 0x20100000-0x201fffff pref] [ 0.587555] workqueue: max_active 576 requested for napi_workq is out of range, clamping between 1 and 512 [ 0.602223] clocksource: Switched to clocksource systick [ 0.608820] NET: Registered protocol family 2 [ 0.613959] tcp_listen_portaddr_hash hash table entries: 512 (order: 0, 4096 bytes, linear) [ 0.622116] TCP established hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.629525] TCP bind hash table entries: 1024 (order: 0, 4096 bytes, linear) [ 0.636369] TCP: Hash tables configured (established 1024 bind 1024) [ 0.642683] UDP hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.649039] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes, linear) [ 0.656092] NET: Registered protocol family 1 [ 0.660372] PCI: CLS 0 bytes, default 32 [ 0.667314] rt-timer 10000100.timer: maximum frequency is 1220Hz [ 0.675534] workingset: timestamp_bits=14 max_order=14 bucket_order=0 [ 0.690114] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.695778] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc. [ 0.723550] Serial: 8250/16550 driver, 2 ports, IRQ sharing disabled [ 0.730954] printk: console [ttyS0] disabled [ 0.735165] 10000c00.uartlite: ttyS0 at MMIO 0x10000c00 (irq = 20, base_baud = 2500000) is a Palmchip BK-3103 [ 0.744781] printk: console [ttyS0] enabled [ 0.744781] printk: console [ttyS0] enabled [ 0.753251] printk: bootconsole [early0] disabled [ 0.753251] printk: bootconsole [early0] disabled [ 0.769028] spi spi0.0: force spi mode3 [ 0.783054] spi-nor spi0.0: s25fl064k (8192 Kbytes) [ 0.788103] 4 fixed-partitions partitions found on MTD device spi0.0 [ 0.794598] Creating 4 MTD partitions on "spi0.0": [ 0.799507] 0x000000000000-0x000000030000 : "u-boot" [ 0.805642] 0x000000030000-0x000000040000 : "u-boot-env" [ 0.812154] 0x000000040000-0x000000050000 : "factory" [ 0.818514] 0x000000050000-0x000000800000 : "firmware" [ 0.828253] 2 uimage-fw partitions found on MTD device firmware [ 0.834375] Creating 2 MTD partitions on "firmware": [ 0.839465] 0x000000000000-0x0000001d989e : "kernel" [ 0.845608] 0x0000001d989e-0x0000007b0000 : "rootfs" [ 0.851701] mtd: device 5 (rootfs) set to be root filesystem [ 0.859454] 1 squashfs-split partitions found on MTD device rootfs [ 0.865845] 0x0000004c9000-0x0000007b0000 : "rootfs_data" [ 0.873311] libphy: Fixed MDIO Bus: probed [ 0.887334] gsw: setting port4 to gmac mode [ 0.892108] libphy: mdio: probed [ 0.897381] mtk_soc_eth 10100000.ethernet: connected port 4 to PHY at mdio-bus:04 [uid=001cc916, driver=Generic PHY] [ 0.908503] mtk_soc_eth 10100000.ethernet: connected port 5 to PHY at mdio-bus:05 [uid=001cc916, driver=Generic PHY] [ 0.919488] mtk_soc_eth 10100000.ethernet: loaded mt7620 driver [ 0.926345] mtk_soc_eth 10100000.ethernet eth0: mediatek frame engine at 0xb0100000, irq 5 [ 0.935331] rt2880_wdt 10000120.watchdog: Initialized [ 0.941991] NET: Registered protocol family 10 [ 0.951875] Segment Routing with IPv6 [ 0.955863] NET: Registered protocol family 17 [ 0.960492] 8021q: 802.1Q VLAN Support v1.8 [ 0.982480] VFS: Mounted root (squashfs filesystem) readonly on device 31:5. [ 0.996632] Freeing unused kernel memory: 1228K [ 1.001283] This architecture does not have kernel memory protection. [ 1.007860] Run /sbin/init as init process [ 1.202152] random: fast init done [ 2.670479] init: Console is alive [ 2.674354] init: - watchdog - [ 4.589318] kmodloader: loading kernel modules from /etc/modules-boot.d/* [ 4.959267] kmodloader: done loading kernel modules from /etc/modules-boot.d/* [ 4.969362] init: - preinit - [ 6.884146] random: jshn: uninitialized urandom read (4 bytes read) [ 6.977820] random: jshn: uninitialized urandom read (4 bytes read) [ 7.144684] random: jshn: uninitialized urandom read (4 bytes read) [ 8.075417] 8021q: adding VLAN 0 to HW filter on device eth0 Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.150693] urandom_read: 4 callbacks suppressed [ 8.150702] random: procd: uninitialized urandom read (4 bytes read) [ 8.395798] mtk_soc_eth 10100000.ethernet eth0: port 4 link up (100Mbps/Full duplex) [ 8.403895] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (100Mbps/Full duplex) [ 8.817985] mount_root: jffs2 not ready yet, using temporary tmpfs overlay [ 8.829913] urandom-seed: Seed file not found (/etc/urandom.seed) [ 8.925865] mtk_soc_eth 10100000.ethernet eth0: port 4 link down [ 8.932171] mtk_soc_eth 10100000.ethernet eth0: port 5 link down [ 8.960577] procd: - early - [ 8.963835] procd: - watchdog - [ 9.159010] procd: - watchdog - [ 9.162660] procd: - ubus - [ 9.352958] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.361369] random: ubusd: uninitialized urandom read (4 bytes read) [ 9.376537] procd: - init - Please press Enter to activate this console. [ 10.579277] kmodloader: loading kernel modules from /etc/modules.d/* [ 10.850233] Loading modules backported from Linux version v5.8-0-gbcf876870b95 [ 10.857632] Backport generated by backports.git v5.8-1-0-g79400d9e [ 10.925076] xt_time: kernel timezone is -0000 [ 10.945813] urngd: jent-rng init failed, err: 2 [ 11.101572] mt76x2e 0000:01:00.0: card - bus=0x1, slot = 0x0 irq=4 [ 11.108237] mt76x2e 0000:01:00.0: ASIC revision: 76120044 [ 11.185194] mt76x2e 0000:01:00.0: ROM patch build: 20141115060606a [ 11.197468] mt76x2e 0000:01:00.0: Firmware Version: 0.0.00 [ 11.203146] mt76x2e 0000:01:00.0: Build: 1 [ 11.207337] mt76x2e 0000:01:00.0: Build Time: 201507311614____ [ 11.218616] mt76x2e 0000:01:00.0: Firmware running! [ 11.316002] PPP generic driver version 2.4.2 [ 11.324237] NET: Registered protocol family 24 [ 11.389058] rt2800_wmac 10180000.wmac: loaded eeprom from mtd device "factory" [ 11.396525] ieee80211 phy1: rt2x00_set_rt: Info - RT chipset 6352, rev 0500 detected [ 11.404468] ieee80211 phy1: rt2x00_set_rf: Info - RF chipset 7620 detected [ 11.505598] kmodloader: done loading kernel modules from /etc/modules.d/* [ 20.510372] random: crng init done [ 43.022387] jffs2_scan_eraseblock(): End of filesystem marker found at 0x0 [ 43.046559] jffs2_build_filesystem(): unlocking the mtd device... [ 43.046642] done. [ 43.054958] jffs2_build_filesystem(): erasing all blocks after the end marker... [ 43.709059] 8021q: adding VLAN 0 to HW filter on device eth0 [ 43.769599] br-lan: port 1(eth0.1) entered blocking state [ 43.775216] br-lan: port 1(eth0.1) entered disabled state [ 43.781164] device eth0.1 entered promiscuous mode [ 43.786115] device eth0 entered promiscuous mode [ 44.726854] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready [ 44.757459] mtk_soc_eth 10100000.ethernet eth0: port 5 link up (100Mbps/Full duplex) [ 44.794638] mtk_soc_eth 10100000.ethernet eth0: port 4 link up (100Mbps/Full duplex) [ 44.815970] br-lan: port 1(eth0.1) entered blocking state [ 44.821562] br-lan: port 1(eth0.1) entered forwarding state [ 44.858417] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready [ 92.299757] done. [ 92.301771] jffs2: notice: (1807) jffs2_build_xattr_subsystem: complete building xattr subsystem, 0 of xdatum (0 unchecked, 0 orphan) and 0 of xref (0 dead, 0 orphan) found. [ 92.544673] overlayfs: upper fs does not support tmpfile. BusyBox v1.31.1 () built-in shell (ash) _______ ________ __ | |.-----.-----.-----.| | | |.----.| |_ | - || _ | -__| || | | || _|| _| |_______|| __|_____|__|__||________||__| |____| |__| W I R E L E S S F R E E D O M ----------------------------------------------------- OpenWrt SNAPSHOT, r14926+1-41b867165d ----------------------------------------------------- === WARNING! ===================================== There is no root password defined on this device! Use the "passwd" command to set up a new password in order to prevent unauthorized SSH logins. -------------------------------------------------- root@OpenWrt:/#


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2021/01/06 13:47
  • by polystera