User Tools

Site Tools


inbox:toh:comfast:comfast_cf-e130n_v2

COMFAST CF-E130N V2

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

The COMFAST CF-E130N is an outdoor 2.4 GHz wireless CPE. It is based on the Qualcomm Atheros QCA9531/9533 SoC, and features one RJ45 10/100 Mbps Ethernet port with PoE in and a 300 Mbps 2.4 GHz 802.11b/g/n radio connected to an internal 5 dBi atenna.

CF-E130N side view (image from comfast.com.cn) CF-E130N right view (image from comfast.com.cn) CF-E130N front view (image from comfast.com.cn) CF-E130N back view (image from comfast.com.cn) CF-E130N internal view (image from comfast.com.cn)

OpenWrt support

Not supported.

Hardware highlights

CPU Ram Flash Network WLAN USB Serial JTag
??? 64 MiB 8 MiB 1x 10/100(?) ??? None Yes ?

Hardware

Info

Architecture MIPS32
Vendor COMFAST
Bootloader U-Boot
System-On-Chip Qualcomm Atheros QCA9531/9533
CPU/Speed EXAMPLE 451 MHz
Flash-Chip
Flash size 2×8 MiB
RAM 64 MiB
Wireless 2.4GHz 802.11bgn
Ethernet 1x 10/100 Mbit/s port
Switch Qualcomm Atheros QCA9531
USB None
Serial Yes
JTAG EXAMPLE Not populated

FIXME 8 Mib or 16 MiB? The messages are really mixed.

Photos

Insert photo of front of the casing

Insert photo of back of the casing

Insert photo of backside label

CF-E130N PCB

Opening the case

To remove the cover and open the device, remove the two screws under the adhesive label (corners low). Then pull out the PCB+antenna block from the case.

Serial

port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:
Insert photo of PCB with markings for serial port

FIXME Replace EXAMPLE by real values.

Serial connection parameters
for COMFAST CF-E130N V2
EXAMPLE 115200, 8N1

JTAG

port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Bootlogs

OEM bootlog

U-Boot 1.1.4-ga1cd7d4b-dirty (May 31 2018 - 16:44:04)

ap143 - Honey Bee 2.0

DRAM: 64 MB Flash: 16 MB

eth0 link down FAIL eth1 link down FAIL Using eth0 device Tx Timed out ping failed; Hit any key to stop autoboot: 1  0 ## Booting image at 9f020000 …

 Image Name:   MIPS OpenWrt Linux-3.10.44
 Created:      2018-10-12   2:47:56 UTC
 Image Type:   MIPS Linux Kernel Image (lzma compressed)
 Data Size:    1060532 Bytes =  1 MB
 Load Address: 80060000
 Entry Point:  80060000
 Verifying Checksum at 0x9f020040 ...OK
 Uncompressing Kernel Image ... OK

No initrd ## Transferring control to Linux (at address 80060000) … ## Giving linux memsize in bytes, 67108864

Starting kernel …

[ 0.000000] Linux version 3.10.44 (dingtengfei@oracle.tecmint.com) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 unknown) ) #1 Fri Oct 12 10:47:07 CST 2018 [ 0.000000] bootconsole [early0] enabled [ 0.000000] CPU revision is: 00019374 (MIPS 24Kc) [ 0.000000] SoC: Qualcomm Atheros QCA9531 ver 2 rev 0 [ 0.000000] Clocks: CPU:650.000MHz, DDR:392.871MHz, AHB:216.666MHz, Ref:25.000MHz [ 0.000000] Determined physical RAM map: [ 0.000000] memory: 04000000 @ 00000000 (usable) [ 0.000000] Initrd not found or empty - disabling initrd [ 0.000000] Zone ranges: [ 0.000000] Normal [mem 0x00000000-0x03ffffff] [ 0.000000] Movable zone start for each node [ 0.000000] Early memory node ranges [ 0.000000] node 0: [mem 0x00000000-0x03ffffff] [ 0.000000] Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. [ 0.000000] Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16256 [ 0.000000] Kernel command line: board=COMFAST-CF-E130N console=ttyS0,115200 mtdparts=spi0.0:64k(u-boot)ro,64k(art)ro,1536k(kernel),6400k(rootfs),64k(configs),64k(nvram)ro,7936k@0x20000(firmware) rootfstype=squashfs,jffs2 noinitrd [ 0.000000] PID hash table entries: 256 (order: -2, 1024 bytes) [ 0.000000] Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) [ 0.000000] Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) [ 0.000000] Writing ErrCtl register=00000000 [ 0.000000] Readback ErrCtl register=00000000 [ 0.000000] Memory: 61280k/65536k available (2273k kernel code, 4256k reserved, 592k data, 204k init, 0k highmem) [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1 [ 0.000000] NR_IRQS:51 [ 0.000000] Calibrating delay loop… 432.53 BogoMIPS (lpj=2162688) [ 0.050000] pid_max: default: 32768 minimum: 301 [ 0.050000] Mount-cache hash table entries: 512 [ 0.060000] NET: Registered protocol family 16 [ 0.070000] MIPS: machine is COMFAST CF-E130N [ 0.510000] ar724x-pci ar724x-pci.0: PCIe link is down [ 0.510000] registering PCI controller with io_map_base unset [ 0.520000] bio: create slab <bio-0> at 0 [ 0.530000] PCI host bridge to bus 0000:00 [ 0.530000] pci_bus 0000:00: root bus resource [mem 0x10000000-0x11ffffff] [ 0.540000] pci_bus 0000:00: root bus resource [io 0x0000] [ 0.540000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff] [ 0.550000] Switching to clocksource MIPS [ 0.550000] NET: Registered protocol family 2 [ 0.560000] TCP established hash table entries: 512 (order: 0, 4096 bytes) [ 0.560000] TCP bind hash table entries: 512 (order: -1, 2048 bytes) [ 0.570000] TCP: Hash tables configured (established 512 bind 512) [ 0.570000] TCP: reno registered [ 0.580000] UDP hash table entries: 256 (order: 0, 4096 bytes) [ 0.580000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes) [ 0.590000] NET: Registered protocol family 1 [ 0.610000] squashfs: version 4.0 (2009/01/31) Phillip Lougher [ 0.610000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) © 2001-2006 Red Hat, Inc. [ 0.620000] msgmni has been set to 119 [ 0.630000] io scheduler noop registered [ 0.630000] io scheduler deadline registered (default) [ 0.640000] Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled [ 0.670000] serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A [ 0.670000] console [ttyS0] enabled, bootconsole disabled [ 0.670000] console [ttyS0] enabled, bootconsole disabled [ 0.680000] ath79-spi ath79-spi: master is unqueued, this is deprecated [ 0.690000] m25p80 spi0.0: found en25qh64a, expected m25p80 [ 0.700000] m25p80 spi0.0: en25qh64a (8192 Kbytes) [ 0.710000] 7 cmdlinepart partitions found on MTD device spi0.0 [ 0.710000] Creating 7 MTD partitions on “spi0.0”: [ 0.720000] 0x000000000000-0x000000010000 : “u-boot” [ 0.720000] 0x000000010000-0x000000020000 : “art” [ 0.730000] 0x000000020000-0x0000001a0000 : “kernel” [ 0.740000] 0x0000001a0000-0x0000007e0000 : “rootfs” [ 0.750000] mtd: device 3 (rootfs) set to be root filesystem [ 0.750000] 1 squashfs-split partitions found on MTD device rootfs [ 0.760000] 0x000000530000-0x0000007e0000 : “rootfs_data” [ 0.760000] 0x0000007e0000-0x0000007f0000 : “configs” [ 0.770000] 0x0000007f0000-0x000000800000 : “nvram” [ 0.780000] 0x000000020000-0x0000007e0000 : “firmware” [ 0.810000] libphy: ag71xx_mdio: probed [ 0.810000] eth0: Atheros AG71xx at 0xba000000, irq 5 [ 1.370000] ag71xx-mdio.1: Found an AR934X built-in switch [ 1.410000] eth1: Atheros AG71xx at 0xb9000000, irq 4 [ 1.970000] ag71xx ag71xx.0: connected to PHY at ag71xx-mdio.1:04 [uid=004dd042, driver=Generic PHY] [ 1.980000] TCP: cubic registered [ 1.980000] NET: Registered protocol family 17 [ 1.990000] 8021q: 802.1Q VLAN Support v1.8 [ 2.000000] VFS: Mounted root (squashfs filesystem) readonly on device 31:3. [ 2.010000] Freeing unused kernel memory: 204K (8032d000 - 80360000) [ 2.940000] init: Console is alive [ 2.940000] init: - watchdog - [ 3.950000] init: - preinit - Press the [f] key and hit [enter] to enter failsafe mode Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level [ 8.170000] jffs2: notice: (383) jffs2_build_xattr_subsystem: complete building xattr subsystem, 2 of xdatum (0 unchecked, 0 orphan) and 13 of xref (0 dead, 2 orphan) found. [ 8.180000] mount_root: switching to jffs2 overlay 529+0 records in 529+0 records out 377+0 records in 377+0 records out [ 8.300000] procd: - early - [ 8.300000] procd: - watchdog - [ 8.930000] procd: - ubus - [ 9.950000] procd: - init - Please press Enter to activate this console. [ 11.680000] i2c /dev entries driver [ 11.700000] u32 classifier [ 11.700000] input device check on [ 11.700000] Actions configured [ 11.710000] Mirror/redirect action on [ 11.720000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea [ 11.730000] Backport generated by backports.git backports-20140320-37-g5c33da0 [ 11.740000] ip_tables: (C) 2000-2006 Netfilter Core Team [ 11.760000] nf_conntrack version 0.5.0 (960 buckets, 3840 max) [ 11.770000] Netfilter messages via NETLINK v0.30. [ 11.820000] xt_time: kernel timezone is -0000 [ 11.930000] PPP generic driver version 2.4.2 [ 11.940000] PPP MPPE Compression module registered [ 11.950000] NET: Registered protocol family 24 [ 12.030000] ieee80211 phy0: Atheros AR9531 Rev:2 mem=0xb8100000, irq=47 [ 20.820000] device eth1 entered promiscuous mode [ 20.850000] br-lan: port 1(eth1) entered forwarding state [ 20.850000] br-lan: port 1(eth1) entered forwarding state [ 21.380000] heart_beat uses obsolete (PF_INET,SOCK_PACKET) configs:do check configs [ 21.830000] br-lan: port 1(eth1) entered disabled state [ 24.510000] device wlan0 entered promiscuous mode [ 31.760000] br-lan: port 2(wlan0) entered forwarding state [ 31.770000] br-lan: port 2(wlan0) entered forwarding state [ 33.770000] br-lan: port 2(wlan0) entered forwarding state


OpenWrt bootlog

COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


Notes

Tags

This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
inbox/toh/comfast/comfast_cf-e130n_v2.txt · Last modified: 2019/11/06 02:23 by kryma