Nokia G-240G-E

Under Construction!
This page is currently under construction. You can edit the article to help completing it.

The Nokia/Alcatel-Lucent G-240G-E router is an ONT used by many ISPs and IAPs as a fiber modem to connect customers to their WiFi router. Manufactured by Nokia Shanghai Bell.

Nokia G-240G-E

Not supported yet. Work In Progress.

CPU Ram Flash Ethernet USB Serial JTAG Fiber Phone DSL
Econet EN7526GT @ 900 MHz 256MB 128MB 4x 10/100/1000 1x 2.0 Yes No Yes Yes No
Architecture MIPS
Vendor TrendChip/Ralink/EcoNet/Airoha/Mediatek
Bootloader Custom UBoot (TCboot)
System-On-Chip EcoNet EN7526GT aka EcoNet EN751221 - MIPS 34Kc V5.8
CPU/Speed 2 Thread 1 Core 900 MHz
RAM Chip Nanya NT5CC128M16JR-EK 256 MB DDR3L 1866Mhz
Flash Chip Macronix/MXIC MX35LF1GE4AB-Z4I 128 MB SPI NAND
Ethernet 4x GbE LAN (10/100/1000Mbit/s)
Fiber 1x GPON SC-APC via Semtech GN25L98 driver
Phone 2x RJ11 SIP & VoIP via Maxlinear/Intel SLLV5 aka Lantiq PEF32002 SLIC
Switch Built in to SoC
USB 1x 2.0
Serial Yes
GPIO Buttons 2 (Reset, LED)
GPIO LEDs 12 (1x RG + 11x G)
Power External 12V 2.0A, with a 3.0 X 5.5 X 12mm connector

View of the entire PCB and chipset layout

There 1 philips screw hidden under the label. Everything else pry opens with the plastic tabs.

It uses 115200 bps baud rate over UART.

Shows what pins to connect to for serial communication

Web GUI is at 192.168.1.254. Username is adminadmin and password is ALC#FGU (sometimes might be AdminGPON/ALC#FGU or ONTUSER/SUGAR2A041). The “Dynamic password” is '; /bin/sh; #.

ritool is a Nokia binary that manipulates the EEPROM settings of the Fiber transciever. To change GPON settings, in UART Uboot environment launch the “ritool” application with the following arguments:

ritool set OperatorID 0000 to allow change of GPON Serial Number (recommended to change back to 'ALCL' once done to prevent internal settings to change upon reset)

ritool set MACAddress xx:xx:xx:xx:xx:xx to change GPON MAC Address

ritool set MfrID XXXX to change Manufacturer or Vendor ID/First 4 letters of the SN

ritool set G984Serial xxxxxxxx to change GPON Serial Number/Last 8 characters of the SN

0x00000000-0x00040000 “bootloader”
0x00040000-0x00080000 “romfile”
0x00080000-0x002a9c9a “kernel”
0x002a9c9a-0x01529c9a “rootfs”
0x00080000-0x01080000 “tclinux”
0x01080000-0x8083e690 “kernel_slave”
0x8083e690-0xb437e690 “rootfs_slave”
0x01080000-0x02080000 “tclinux_slave”
0x02080000-0x04980000 “yaffs”
0x06e40000-0x07000000 “reservearea”

BGA IC Xtal:1 DDR3 init. DRAMC init done. Calculate size. DRAM size=256MB Set new TRFC. ddr-1066 7512DRAMC V1.3.2 (0) Set SPI Flash Clock to 25 Mhz EN751221 at Mon Mar 16 14:09:58 CST 2020 version 1.1 free bootbase Memory size 256MB Set SPI Flash Clock to 25 Mhz spi_nand_probe: mfr_id=0xc2, dev_id=0x12 Dected SPI NAND Flash : _SPI_NAND_DEVICE_ID_MXIC35LF1G, Flash Size=0x8000000 bmt pool size: 81 BMT & BBT Init Success tclinux partition size = 0x1000000, real size = 0x149ae24 tclinux partition size < its real size tclinux_slave partition size = 0x1000000, real size = 0xb32fa972 tclinux_slave partition size < its real size boardType: G240GE_CI Press any key in 3 secs to enter boot command mode. .................... commit = 0 next_active = 0 image0_is_valid = 1 image1_is_valid = 0 boot_fail_num = 6 read OpreatorID succeed = XXXX leave bootloader-image0_is_valid = 1 leave bootloader-image1_is_valid = 0 #######select0 0x80000 #######kernel_size 2268314 #######kernel_size 2293760 Decompress to 80002000 free_mem_ptr=80750000 free_mem_ptr_end=807B0000 from main *********run kernel 0******** trx_header_len = 256 kernel_size = 2293760 Uncompressing [LZMA] ... done. Initializing cgroup subsys cpuset Initializing cgroup subsys cpu Initializing cgroup subsys cpuacct Linux version 3.18.21 (buildmgr@AONTDH77) (gcc version 4.9.3 (Buildroot 2015.08.1) ) #4 SMP Mon Mar 16 14:13:34 CST 2020 ISPRAM0: PA=00500000,Size=00010000,enabled memsize:256MB EcoNet EN751221 SOC prom init bootconsole [early0] enabled CPU0 revision is: 00019558 (MIPS 34Kc) Determined physical RAM map: memory: 0fffe000 @ 00002000 (usable) Wasting 64 bytes for tracking 2 unused pages Zone ranges: Normal [mem 0x00002000-0x0fffffff] Movable zone start for each node Early memory node ranges node 0: [mem 0x00002000-0x0fffffff] Initmem setup node 0 [mem 0x00002000-0x0fffffff] Detected 1 available secondary CPU(s) Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes PERCPU: Embedded 9 pages/cpu @81203000 s5728 r8192 d22944 u36864 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 65022 Kernel command line: es=1 PID hash table entries: 1024 (order: 0, 4096 bytes) Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Writing ErrCtl register=0006dc4d Readback ErrCtl register=0006dc4d nmi base is 8124c200 Memory: 252984K/262136K available (5176K kernel code, 198K rwdata, 940K rodata, 196K init, 273K bss, 9152K reserved) SLUB: HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1 Hierarchical RCU implementation. NR_IRQS:64 tc3162_time_init: Init bus timeout and watchdog plat_set_irq_affinity: cpu 0 plat_set_irq_affinity: cpu 0 vpe_id 0 plat_set_irq_affinity: irq_vpe0 1 irq_vpe1 0, irq = 10 plat_set_irq_affinity: irq num 10 plat_set_irq_affinity: cpu 0 plat_set_irq_affinity: cpu 0 vpe_id 0 plat_set_irq_affinity: irq_vpe0 1 irq_vpe1 0, irq = 33 plat_set_irq_affinity: irq num 33 CPU frequency 900.00 MHz plat_time_init: Entered, mips_timer_ack ptr is [800075d0] Using 200.000 MHz high precision timer. r4k_clockevent_init: setup_irq OK, irq is [31] console [ttyS0] enabled console [ttyS0] enabled bootconsole [early0] disabled bootconsole [early0] disabled Calibrating delay loop... 597.60 BogoMIPS (lpj=2988032) pid_max: default: 32768 minimum: 301 Security Framework initialized Mount-cache hash table entries: 1024 (order: 0, 4096 bytes) Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes) Initializing cgroup subsys devices Initializing cgroup subsys freezer Initializing cgroup subsys debug 34K sync es set to 1. Config7: 0x80080500 ISPRAM0: PA=00500000,Size=00010000,enabled Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes. Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes CPU1 revision is: 00019558 (MIPS 34Kc) Synchronize counters for CPU 1: done. Brought up 2 CPUs NET: Registered protocol family 16 PCIe driver version: 751221.5.20170807 MT7512_pcie_init check pcie link up status: isRC0_LINKUP=0 isRC1_LINKUP=0 PCI-E RC0 & RC1 can not link up usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 8 NET: Registered protocol family 20 Switched to clocksource MIPS NET: Registered protocol family 2 TCP established hash table entries: 2048 (order: 1, 8192 bytes) TCP bind hash table entries: 2048 (order: 2, 16384 bytes) TCP: Hash tables configured (established 2048 bind 2048) TCP: reno registered UDP hash table entries: 256 (order: 1, 8192 bytes) UDP-Lite hash table entries: 256 (order: 1, 8192 bytes) NET: Registered protocol family 1 TC3162 hardware watchdog module loaded. futex hash table entries: 512 (order: 2, 16384 bytes) squashfs: version 4.0 (2009/01/31) Phillip Lougher ntfs: driver 2.1.31 [Flags: R/W DEBUG]. jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc. msgmni has been set to 494 NET: Registered protocol family 38 io scheduler noop registered (default) ttyS0 at I/O 0xbfbf0003 (irq = 1, base_baud = 7200) is a TC3162 ECNT ring buffer init success brd: module loaded SPI Flash Init Start Found no SPI flash device IS_SPIFLASH=0x0, IS_NANDFLASH=0x2, (0xBFA10114)=0x6) SPI_NAND_Flash_init: before init, mtx_mode_tog=0xl9, manaul_en=0x1 spi_nand_probe: mfr_id=0xc2, dev_id=0x12 Dected SPI NAND Flash : _SPI_NAND_DEVICE_ID_MXIC35LF1G, Flash Size=0x8000000 spi nand flash tc3162: flash device 0x01000000 at 0x1c000000 EN7512 mtd init: spi nand probe enter [spi_nand_setup] : Enter nand: device found, Manufacturer ID: 0xc2, Chip ID: 0x12 nand: Macronix _SPI_NAND_DEVICE_ID_MXIC35LF1G nand: 128MiB, SLC, page size: 2048, OOB size: 64 nand_scan_ident ok [spi_nand_setup]: chip size = 0x8000000, erase_shift=0x11 calc_bmt_pool_size : need_valid_block_num=0x51, total_block=0x400 bmt pool size: 81 BMT & BBT Init Success Creating 16 MTD partitions on "EN7512-SPI_NAND": 0x000000000000-0x000000040000 : "bootloader" 0x000000040000-0x000000080000 : "romfile" 0x000000080000-0x000000380000 : "kernel" 0x000000380000-0x000002280000 : "rootfs" 0x000002280000-0x000002580000 : "kernel_slave" 0x000002580000-0x000004480000 : "rootfs_slave" 0x000004480000-0x000004780000 : "kernel_oflt" 0x000004780000-0x000005380000 : "rootfs_oflt" 0x000005380000-0x000005b80000 : "config" 0x000005b80000-0x000006780000 : "log" 0x000006780000-0x000006d80000 : "extfs" 0x000006d80000-0x000006dc0000 : "bosa" 0x000006dc0000-0x000006e00000 : "flag" 0x000006e00000-0x000006e40000 : "flagback" 0x000006e40000-0x000006e80000 : "ri" 0x000006e80000-0x000006ec0000 : "riback" commit = 0 next_active = 0 image0_is_valid = 1 image1_is_valid = 0 boot_fail_num = 7 active = 0 start rootfs select img A 3 PPP generic driver version 2.4.2 PPP BSD Compression module registered PPP Deflate Compression module registered NET: Registered protocol family 24 751221 USB PHY config, enable port0 port1 USB driver version: 751221.kernel3.3.20170822 port 0 u2_slew_rate_calibration FM_OUT value = 147(0x00000093) SR calibration value = 4 port 1 u2_slew_rate_calibration FM_OUT value = 146(0x00000092) SR calibration value = 4 xhci-hcd xhci-hcd: xHCI Host Controller xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 1 plat_set_irq_affinity: cpu 0 plat_set_irq_affinity: cpu 0 vpe_id 0 plat_set_irq_affinity: cpu 1 plat_set_irq_affinity: cpu 1 vpe_id 0 plat_set_irq_affinity: irq_vpe0 1 irq_vpe1 1, irq = 18 plat_set_irq_affinity: irq num 18 xhci-hcd xhci-hcd: irq 18, io mem 0x1fb90000 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected xhci-hcd xhci-hcd: xHCI Host Controller xhci-hcd xhci-hcd: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected usbcore: registered new interface driver cdc_acm cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters usbcore: registered new interface driver usbserial usbcore: registered new interface driver usbserial_generic usbserial: USB Serial support registered for generic usbcore: registered new interface driver cypress_m8 usbserial: USB Serial support registered for DeLorme Earthmate USB usbserial: USB Serial support registered for HID->COM RS232 Adapter usbserial: USB Serial support registered for Nokia CA-42 V2 Adapter usbcore: registered new interface driver ftdi_sio usbserial: USB Serial support registered for FTDI USB Serial Device hidraw: raw HID events driver (C) Jiri Kosina usbcore: registered new interface driver usbhid usbhid: USB HID core driver Netfilter messages via NETLINK v0.30. nf_conntrack version 0.5.0 (3952 buckets, 15808 max) nf_tables: (c) 2007-2009 Patrick McHardy <kaber@trash.net> nf_tables_compat: (c) 2012 Pablo Neira Ayuso <pablo@netfilter.org> TCP: cubic registered Initializing XFRM netlink socket NET: Registered protocol family 10 ip6_tables: (C) 2000-2006 Netfilter Core Team sit: IPv6 over IPv4 tunneling driver NET: Registered protocol family 17 NET: Registered protocol family 15 bridge: automatic filtering via arp/ip/ip6tables has been deprecated. Update your scripts to load br_netfilter if you need this. l2tp_core: L2TP core driver, V2.0 l2tp_ppp: PPPoL2TP kernel driver, V2.0 l2tp_netlink: L2TP netlink interface 8021q: 802.1Q VLAN Support v1.8 plat_set_irq_affinity: cpu 0 plat_set_irq_affinity: cpu 0 vpe_id 0 plat_set_irq_affinity: cpu 1 plat_set_irq_affinity: cpu 1 vpe_id 0 plat_set_irq_affinity: irq_vpe0 1 irq_vpe1 1, irq = 1 plat_set_irq_affinity: irq num 1 tc3162ser_startup VFS: Mounted root (squashfs filesystem) readonly on device 31:3. Freeing unused kernel memory: 196K (8062f000 - 80660000) mipsmt_sys_sched_setaffinity new_mask origin value is 00000003 mipsmt_sys_sched_setaffinity new_mask changed value is 00000001 UBI: attaching mtd8 to ubi0 UBI: scanning is finished UBI: attached mtd8 (name "config", size 8 MiB) to ubi0 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 64, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 4/2, WL threshold: 4096, image sequence number: 0 UBI: available PEBs: 0, total reserved PEBs: 64, PEBs reserved for bad PEB handling: 0 UBI: background thread "ubi_bgt0d" started, PID 566 UBI device number 0, total 64 LEBs (8126464 bytes, UBI: attaching mtd9 to ubi1 7.8 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) UBI: scanning is finished UBI: attached mtd9 (name "log", size 12 MiB) to ubi1 UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes UBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048 UBI: VID header offset: 2048 (aligned 2048), data offset: 4096 UBI: good PEBs: 96, bad PEBs: 0, corrupted PEBs: 0 UBI: user volume: 1, internal volumes: 1, max. volumes count: 128 UBI: max/mean erase counter: 3/1, WL threshold: 4096, image sequence number: 0 UBI: available PEBs: 0, total reserved PEBs: 96, PEBs reserved for bad PEB handling: 0 UBI: background thread "ubi_bgt1d" started, PID 568 UBI device number 1, total 96 LEBs (12189696 bytes, 11.6 MiB), available 0 LEBs (0 bytes), LEB size 126976 bytes (124.0 KiB) UBIFS: background thread "ubifs_bgt0_0" started, PID 571 UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 0, volume 0, name "configfs" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 6348800 bytes (6 MiB, 50 LEBs), journal size 1396736 bytes (1 MiB, 11 LEBs) UBIFS: reserved for root: 0 bytes (0 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID F69B2EA6-DAC0-4FDF-9B53-1D6E5C6B2F77, small LPT model UBIFS: background thread "ubifs_bgt1_0" started, PID 573 UBIFS: recovery needed UBIFS: recovery completed UBIFS: mounted UBI device 1, volume 0, name "logfs" UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes UBIFS: FS size: 10412032 bytes (9 MiB, 82 LEBs), journal size 1904640 bytes (1 MiB, 15 LEBs) UBIFS: reserved for root: 0 bytes (0 KiB) UBIFS: media format: w4/r0 (latest is w4/r0), UUID 133C24EE-1AD4-4B44-AE0E-BB7BD68D3147, small LPT model committed:0 actived:0 sh: can't open '/usr/exe/ckpswd.sh' random: sed urandom read with 45 bits of entropy available ln: /etc/Wireless/RT2860AP_AC/RT30xxEEPROM.bin: No such file or directory buildinfo : 3FE46606BGCA40 we are now image0 ! update image_version from bootup system no need to update image0 version Loading RI driver... install nand_drv driver! scfg module install ok. [hcfg] try to load /usr/cfg/hcfg/3FE48157AAAA.cfg GPIO ledconf special handler Loading SDK modules... ===========tune parmeter=========== /usr/exe/sdk_moudles.sh: line 13: can't create /proc/sys/net/netfilter/nf_conntrack_icmp_timeout: nonexistent directory /usr/exe/sdk_moudles.sh: line 19: can't create /proc/net/skbmgr_4k_limi: nonexistent directory insmod eth driver netif_napi_add() called with weight 128 on device eth qdmamgr_lan set ratelimit Exec. Successful Exec. Successful and the accuracy is 8kbps Exec. Successful and the accuracy is 8kbps insmod pon driver chmod: /lib/modules/3.18.21/gre.ko: Read-only file system chmod: /lib/modules/3.18.21/ip_gre.ko: Read-only file system chmod: /lib/modules/3.18.21/ipip.ko: Read-only file system insmod koffload driver insmod: can't insert '/lib/driver/koffload.ko': unknown symbol in module or invalid parameter qdmamgr_wan set ratelimit Exec. Successful Exec. Successful and the accuracy is 8kbps Exec. Successful and the accuracy is 8kbps sys memwl bfb51534 0xa0000801 // set the DS BC to 800pps speed limit // FR ALU02592454 ethphxcmd set ratelimit BC MC 64*7pps on switch *reg=0000211c value:68070707 *reg=0000221c value:68070707 *reg=0000231c value:68070707 *reg=0000241c value:68070707 *reg=0000261c value:4a0c0c0c (ext_switch:1) *reg=0000261c value:4a0c0c0c (ext_switch:0) ethphxcmd set ratelimit MLD IGMP PPPOE ARP RARP PAE BPDU DHCPV6 DHCPV4 *reg=0000001c value:00106010 *reg=00000020 value:00160016 *reg=00000024 value:04100210 *reg=000000a4 value:00100010 *reg=00000020 value:00160016 (ext_switch:0) insmod hw_nat.ko done ====bind irq to cpu===== sh: XXXA: unknown operand sys memwl bfb50284 0x00000003 sys memwl bfb50294 0x00000000 sys memwl bfb50298 0x00000000 sys memwl BFB50300 0x00000000 sys memwl BFB50304 0x00000000 sys memwl BFB50308 0x00000000 sys memwl BFB5030C 0x00000000 sys memwl BFB50310 0x00000000 sys memwl BFB50314 0x00000000 sys memwl BFB50318 0x00000000 sys memwl BFB5031C 0x00000000 sys memwl BFB50320 0x00000000 sys memwl BFB50324 0x00000000 sys memwl BFB50328 0x00000000 sys memwl BFB5032C 0x00000000 sys memwl bfaf2000 0x7f7f0010 sys memwl bfac030c 0x80000000 Loading Dying Gasp driver... Loading NetlinkMsg driver... Loading WIFI driver... Loading GPIOMGR driver... Loading GPIOLED driver... Loading BTN driver... button_task_init: btn_get_cfgtbl success btn_poll_task_init: kthread_run btn_poll_task success btn_event_task_init: success Loading BOSA driver... Semtech.GN25L98 ***creat bosa symbol link*** ***load GN25L98 bosa*** Loading USB driver... there is 1 usb port on board There is 1 USB port no board, insmod USB drivers Loading VLANCTL driver... Loading PHYADPT driver... Loading FWDRV driver... Loading IGMP driver... igmpdrv k_igmp_drv_init igmpmap IgmpMapFilterConfig IPTV Filter mode changed from 1 to 5 Loading DHCP driver Loading VOIP driver... There is 2 POTS, voice supported insmod mtk seperated slic solution init mod-ksocket init mod-acodec init mod-foip3 pid 1124's current affinity mask: 1 pid 1124's new affinity mask: 2 taskset: invalid number '0x8' pid 1134's current affinity mask: 1 pid 1134's new affinity mask: 2 pid 1132's current affinity mask: 1 pid 1132's new affinity mask: 2 pid 1133's current affinity mask: 1 pid 1133's new affinity mask: 2 insmod lantiq driver [Write]pin_no 254 write value is 1 [Write]pin_no 254 write value is 0 [Write]pin_no 254 write value is 1 Loading KLPD driver... Loading KCLOGS driver... Start applications... Copy omci capability files... /usr/exe/mtk_setup.sh: line 66: copy_omci_cfg_files: not found Start appmgr... [startup] appmgr starting [startup] runing /bin/messagebus start & 2 [startup] runing /sbin/msgmgr & $Starting system message bus: cat: can't open '/configs/valgrind_module.cfg': No such file or directory Start_voice... 2 cp: can't stat '/usr/etc/alcatel/config/vpp_tr69': No such file or directory [startup] runing /sbin/ledmgr & /bin/sh: /sbin/ledmgr: not found [startup] runing /sbin/wifihostd & [startup] runing /sbin/ndk_wand & [startup] runing /sbin/rgwd & [startup] loading cfgmgr [startup] runing /sbin/cfgmgr [IPC_TIMER]Start timer ... [ndbus][dbus][1230: 0x77cb5310][24.297236][wa][ndk_timer][ndbusMainLoop:555]Main thread errno address:0x77cb5778 [ndbus][dbus][1230: 0x77ab6500][24.384538][wa][ndk_timer][thread_entry:463]Child thread errno address:0x77ab6968 ====================@Voice started@================= Start web server... system_call+150: touch /tmp/WLAN_IS_RUNNING Start diagnosis ... self test... opid = XXXX partNumber = 3FE48157AAAA variant = AA BOSA module access OK! phy[1]_id = 0x3a29412 phy[2]_id = 0x3a29412 phy[3]_id = 0x3a29412 phy[4]_id = 0x3a29412 No usb device detected on the board USBc SLIC TYPE: SLIC ERROR logrotate: Logdir /var/log/ missing Generating syslog.conf syslogd starting klogd starting [ndbus][dbus][1250: 0x771ef330][26.534069][wa][wifihostd][ndbusMainLoop:555]Main thread errno address:0x771ef798 [ndbus][dbus][1250: 0x76a58500][26.536784][wa][wifihostd][thread_entry:463]Child thread errno address:0x76a58968 Daemon silent 120 second! cp: can't stat '/etc/xmpp.conf': No such file or directory ndk wand starting ... rgw_wan_init rgwd starting ... [ndbus][dbus][1291: 0x77eb9320][28.100109][fa][rgwd][ndbusTransmit:104]an error occurred on (0x772b80) when nokia.ndk.dnsproxy.itf.api:LoadHostsCache, ms=5000 : The name nokia.ndk.dnsproxy was not provided by any .service files [ndbus][dbus][1284: 0x77907000][28.186493][wa][ndk_wand][ndbusMainLoop:555]Main thread errno address:0x77907468 [ndbus][dbus][1284: 0x772874f0][28.214288][wa][ndk_wand][thread_entry:463]Child thread errno address:0x77287958 sh: root: unknown operand initMemoryMngt(): potsNum = 2, adjust_syssemi_size = 692224, adjust_sysheap_size = 614400 common_pools: need 149248 bytes memory msgbuf_pool_appl: need 117584 bytes memory[startup] cfgmgr is running nr_commands=0,max_links=200 redirect_mode_set 139 mode=2 nr_commands=1,max_links=200 nr_commands=2,max_links=200 nr_commands=3,max_links=200 can't open configuration file [//etc/vtysh.conf] Hello, Welcome to User CLI (version 0.95). SipwStartup, fetched maxPrtZips=2 user> nr_commands=4,max_links=200 === MsgHandler::initTable : partNumber =3FE48157AAAA === enter getCurrentLineMap... nr_commands=5,max_links=200 GVHW initialization, current onu_maxlines 2 is Use NSB intel SLIC driver for mtk nr_commands=6,max_links=200 [startup] cfgmgr start loading DB iptables: No chain/target/match by that name. [ndbus][dbus][1291: 0x77eb9320][31.825457][wa][rgwd][ndbusMainLoop:555]Main thread errno address:0x77eb9788 [ndbus][dbus][1291: 0x777ca4f0][31.828239][wa][rgwd][thread_entry:463]Child thread errno address:0x777ca958 Create sipwQ =65538 nr_commands=7,max_links=200 VDSP_GetInstance:275 nr_commands=8,max_links=200 [Adam] Change log level to (EVA_LOG_ERR). [GDI] Change log level to (EVA_LOG_ERR). #sipcommon_root start nr_commands=9,max_links=200 #InitCommon start nr_commands=10,max_links=200 nr_commands=11,max_links=200 nr_commands=12,max_links=200 leave tm_event() [startup] cfgmgr after loading database [sys] yapi registerContainer(cid): 4 nr_commands=13,max_links=200 nr_commands=14,max_links=200 nr_commands=15,max_links=200 #pmc start #vm start 1970-01-01 00:00:33[in][VOIP]exe_entry.c:113:#vm start #linetest start SLID Disabled1970-01-01 00:00:33[in][VOIP]exe_entry.c:120:#linetest start nr_commands=16,max_links=200 start load custom config Wan System Configuration ======================================================= model: 0 defaultGwMode: 0 staticDefaultGwItfName: policyRoutingMode: 1 dnsMode: 1 serialNumber: ALCLFC3CDB86 oui: 302364 pppConLostMode: 0 operatorId: XXXX snInOp60Rule: 0 dhcpIntervalMode: 0 op60OperatorMode: 1 dhcpMaxInitTimer: 0 dhcpMaxSessTimer: 16 upLinkWorkMode: Normal isBrgSupported: 0 ======================================================= [startup] cfgmgr syncdata2rgwd [ndbus][dbus][1291: 0x77eb9320][34.831641][fa][rgwd][ndbusTransmit:104]an error occurred on (0x772b80) when nokia.ndk.lanhostd:FindLanhostEntry, ms=5000 : The name nokia.ndk.lanhostd was not provided by any .service files [startup] cfgmgr syncdata2rgwd done sh: can't create /proc/sys/net/bridge/bridge-nf-filter-vlan-tagged: nonexistent directory sal_netModelInit:L1816 [DEBUG]: to be implemented for brcm Fill DB initial values. ERR sal_hgu_init: t=35:123 Invoked Function stl_LogServerObject() is called Function stl_LogServerObject() is called Function stl_LogServerObject() is called Function stl_LogServerObject() is called Function stl_LogServerObject() is called Function stl_LogServerObject() is called Function stl_LogServerObject() is called InstanceAlias is OFF [startup] cfgmgr entering main loop [ndbus][dbus][1386: 0x7796b000][35.917060][wa][cfgmgr][ndbusMainLoop:555]Main thread errno address:0x7796b478 [ndbus][dbus][1386: 0x761e34f0][35.920693][wa][cfgmgr][thread_entry:463]Child thread errno address:0x761e3968 sh: /sbin/agent: not found init usb succeed! [startup stage1_boot 0/71] -> cfgmgr cfg_bootevtmgr [startup] cfgmgr find_voip_interface out [ndbus][dbus][1477: 0x7771d000][36.210125][wa][ramond][ndbusMainLoop:555]Main thread errno address:0x7771d478 [ndbus][dbus][1477: 0x7734b4f0][36.212312][wa][ramond][thread_entry:463]Child thread errno address:0x7734b968 [startup] cfgmgr find_voip_interface out [startup] cfgmgr running /sbin/evtmgr & [startup stage1_boot 0/71] <- cfgmgr cfg_bootevtmgr [76ms] [startup stage1_boot 1/71] -> cfgmgr cfg_bootUplinkMgr tr181_enabled: TR181 = 0 [startup stage1_boot 1/71] <- cfgmgr cfg_bootUplinkMgr [63ms] [startup stage1_boot 2/71] -> cfgmgr cfg_bootDeviceInfo [startup] cfgmgr: InternetGatewayDevice.DeviceInfo.X_ASB_COM_AbstractSerialNumber is ALCLFC3CDB86 [startup stage1_boot 2/71] <- cfgmgr cfg_bootDeviceInfo [275ms] [startup stage1_boot 3/71] -> cfgmgr cfg_bootUps [startup stage1_boot 3/71] <- cfgmgr cfg_bootUps [60ms] [startup stage1_boot 4/71] -> cfgmgr cfg_bootportMgr [startup stage1_boot 4/71] <- cfgmgr cfg_bootportMgr [144ms] [startup stage1_boot 5/71] -> cfgmgr cfg_bootomciMgr UPS main() is starting........ [startup stage1_boot 5/71] <- cfgmgr cfg_bootomciMgr [273ms] [startup stage1_boot 6/71] -> cfgmgr cfg_bootcfmMgr [startup stage1_boot 6/71] <- cfgmgr cfg_bootcfmMgr [112ms] [startup stage1_boot 8/71] -> cfgmgr cfg_bootSfuPreCfgFlag [startup stage1_boot 8/71] <- cfgmgr cfg_bootSfuPreCfgFlag [44ms] [startup stage1_boot 9/71] -> cfgmgr cfg_bootCleanWanData PortMgr main() is starting........ isInitializedCfmTxRx >>>isBatteryPower(0), isBatteryMissing(0), isBatteryFailure(0), isBatteryLow(0) >>>>>>SAL_ChangeLEDByPowerState BoardType=25 [startup stage1_boot 9/71] <- cfgmgr cfg_bootCleanWanData [795ms] [startup stage1_boot 14/71] -> cfgmgr cfg_bootWan cfm_register_callback init succeeded, error = 0x00000000 EthOAM -> ethOAM_RawSock_Init() -> OK [startup] evtmgr: starting without voip interface [01-01 00:00:39][OMCI]isInitializedParser() [startup] evtmgr: enter main loop. libONU_HGUSinglePort() PPTP=All [01-01 00:00:39][OMCI]********OMCI Config Data Begin**************** [01-01 00:00:39][OMCI]****ONU Type : 0 [01-01 00:00:39][OMCI]****max lan num : 4 [01-01 00:00:39][OMCI]****max wifi num: 0 [01-01 00:00:39][OMCI]****max wifi id start: 4 [01-01 00:00:39][OMCI]****check wifi state: no [01-01 00:00:39][OMCI]****voip stream map port: 5 [01-01 00:00:39][OMCI]**Reset igmp snooping. **port 0 config by omci: 1 [01-01 00:00:39][OMCI]****port 1 config by omci: 1 [01-01 00:00:39][OMCI]****port 2 config by omci: 1 [01-01 00:00:39][OMCI]****port 3 config by omci: 1 [01-01 00:00:39][OMCI]****dscp to Pbit for untag Config By OMCI: yes [01-01 00:00:39][OMCI]****support double tag rules us: yes [01-01 00:00:39][OMCI]****support double tag rules ds: yes [01-01 00:00:39][OMCI]****support pbit Unmatch Rules: yes [01-01 00:00:39][OMCI]****support Bcast Unmatch Rules: no [01-01 00:00:39][OMCI]****support omci manage HGU port: no [01-01 00:00:39][OMCI]****HGU single port=false [01-01 00:00:39][OMCI]****support omci replace after ranging : no [01-01 00:00:39][OMCI]****support Dynamic Tpid : no [01-01 00:00:39][OMCI]****support Cox : no [01-01 00:00:39][OMCI]****factory mode: 0 [01-01 00:00:39][OMCI]****support 1588 : no [01-01 00:00:39][OMCI]****support SyncE : no [01-01 00:00:39][OMCI]********OMCI Config Data End**************** [01-01 00:00:39][OMCI] user_port class domain =================================== [01-01 00:00:39][OMCI] 1 ETH SFU [01-01 00:00:39][OMCI] 2 ETH SFU [01-01 00:00:39][OMCI] 3 ETH SFU [01-01 00:00:39][OMCI] 4 ETH SFU [01-01 00:00:39][OMCI] 5 POTS SFU [01-01 00:00:39][OMCI]=================================== Set inetnert LED mode is same: 0 opid = XXXX partNumber = 3FE48157AAAA variant = AA BOSA module access OK! phy[1]_id = 0x3a29412 phy[2]_id = 0x3a29412 phy[3]_id = 0x3a29412 phy[4]_id = 0x3a29412 No usb device detected on the board USBc SLIC TYPE: SLIC ERROR opid = XXXX partNumber = 3FE48157AAAA variant = AA BOSA module access OK! phy[1]_id = 0x3a29412 phy[2]_id = 0x3a29412 phy[3]_id = 0x3a29412 phy[4]_id = 0x3a29412 No usb device detected on the board USBc SLIC TYPE: SLIC ERROR libigmp_getPacketIsolation() get packet isolation is 1 [01-01 00:00:39][OMCI]InitPortStream() maxPort=4, enet=4,moca=0 [01-01 00:00:39][OMCI]InitPortStream:: ONU type is SFU EthManageItf::getInstance: without switch. Bridge-Interface:[1]'s type:[0]. be ready to set Priority for Bridge-Interface:[1]. get the port:[1]'s PhyPort:[0] info for Board:[G-240G-E] Success. hal_eth_set_port_domain userport 1, domain isHGU 0 ,type:0 Bridge-Interface:[2]'s type:[0]. be ready to set Priority for Bridge-Interface:[2]. get the port:[2]'s PhyPort:[1] info for Board:[G-240G-E] Success. hal_eth_set_port_domain userport 2, domain isHGU 0 ,type:0 Bridge-Interface:[3]'s type:[0]. be ready to set Priority for Bridge-Interface:[3]. get the port:[3]'s PhyPort:[2] info for Board:[G-240G-E] Success. hal_eth_set_port_domain userport 3, domain isHGU 0 ,type:0 Bridge-Interface:[4]'s type:[0]. be ready to set Priority for Bridge-Interface:[4]. get the port:[4]'s PhyPort:[3] info for Board:[G-240G-E] Success. hal_eth_set_port_domain userport 4, domain isHGU 0 ,type:0 is_xfp: sfp_get_type fail, ret=-1 RSSI_lib_get: getSFPPartNumber failed >>>>>>>>printThresh ponRxHighThresh = -7.000571 ponRxLowThresh = -27.958799 ponTxHighThresh = 6.000031 ponTxLowThresh = -0.499761 ponBiasHighThresh = 70.000000 ponBiasLowThresh = 1.000000 ponTempLowThresh = -5.000000 ponTempHighThresh = 85.000000 ponVolHighThresh = 3.600000 ponVolLowThresh = 3.000000 ponTempLowWarnThresh = 0.000000 ponTempHighWarnThresh = 80.000000 ponVolHighWarnThresh = 3.470000 ponVolLowWarnThresh = 3.130000 ponBiasHighWarnThresh = 0.000000 ponBiasLowWarnThresh = 0.000000 ponRxHighWarnThresh = 0.000000 ponRxlLowWarnThresh = 0.000000 ponTxHighWarnThresh = 0.000000 ponTxLowWarnThresh = 0.000000 iptables: No chain/target/match by that name. [01-01 00:00:39][OMCI]get qid failed,errno=2,err=No such file or directory [01-01 00:00:39][OMCI]get qid failed,errno=2,err=No such file or directory [OMCI]HAL_OMCI_FUNC_GET_PONTAG PORT_CONFIG_DATA message received timer created successfully with id 538f18 timer created successfully with id 538fa8 Voice Service PortMgr Created! timer created successfully with id 539180 timer created successfully with id 539210 Eth Service PortMgr Created! timer created successfully with id 538fb8 timer created successfully with id 5393a8 Wifi PortMgr Created! timer created successfully with id 539220 timer created successfully with id 539548 Usb PortMgr Created! [01-01 00:00:39][OMCI]reset_all_tsched ... ip6tables: No chain/target/match by that name. [startup stage1_boot 14/71] <- cfgmgr cfg_booigmpdrv k_igmp_ioctl_set_port_type:571 Eth_1 port_type =0 tWigmpbl hal_kernel_create_vlan_entry_id:2317 Eth_1 create entryId(4294967295) NOT SUPPORT! an [2357ms] [startup stage1_boot 16/71] -> cfgmgr cfg_bootIGMP igmpIntLanPortType begin! igmpIntLanPortTypigmpdrv k_igmp_ioctl_set_port_type:571 Eth_2 port_type =0 eigmpbl hal_kernel_create_vlan_entry_id:2317 Eth_2 create entryId(4294967295) NOT SUPPORT! isSupportLan(1), lanPortNum(4)! GM:hal_igmp_set_uni_port_type uniport 1 type 0igmpInitLanPortType: set portClass(0), userPort(1), portType(0) GM:higmpdrv k_igmp_ioctl_set_port_type:571 Eth_3 port_type =0 aligmpbl hal_kernel_create_vlan_entry_id:2317 Eth_3 create entryId(4294967295) NOT SUPPORT! _igmp_set_uni_port_type uniport 2 type 0igmpInitLanPortType: set portClass(0), userPort(2), portType(0) free one time entry GM:higmpdrv k_igmp_ioctl_set_port_type:571 Eth_4 port_type =0 aigmpbl hal_kernel_create_vlan_entry_id:2317 Eth_4 create entryId(4294967295) NOT SUPPORT! l_igmp_set_uni_port_type uniport 3 type 0igmpInitLanPortType: set portClass(0), userPort(3), portType(0) GM:hal_igmp_set_uni_port_type uniport 4 type 0igmpInitLanPortType: set portClass(0), userPort(4), portType(0) igmpInitWifiPortType begin rutIgmp_init() rutMld_startMldProxy rutMld_stopMldProxy macMT7530Setqosparam(): port 1 qos_mode 0 halmacMT7530Setqosparam(): port 2 qos_mode 0 _qos_init_ds_qos_switch: port 0, rt 0 halmacMT7530Setqosparam(): port 3 qos_mode 0 _qos_init_ds_qos_switch: port 1, rt 0 halmacMT7530Setqosparam(): port 4 qos_mode 0 _qos_init_ds_qos_switch: port 2, rt 0 hal_qos_init_ds_qos_switch: port 3, rt 0 method = HW_NAT_TAB_CLEAN killall: mld: no process killed No need to set wan info, wanIfName= done [startup stage1_boot 16/71] <- cfgmgr cfg_bootIGMP [274ms] [startup stage1_boot 17/71] -> cfgmgr cfg_bootSfuLan method = HW_NAT_TAB_CLEAN done 1970-01-01 00:00:40[in]cfgmgr Add LANHostCfg: flag=(0);DHCPServerEnable=0;DHCPServerConfigurable=1;MinAddress=192.168.1.64;MaxAddress=192.168.1.253;SubnetMask=255.255.255.0;DHCPLeaseTime=86400; method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done Sorry, rule does not exist. method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done brctl: bridge br0: File exists method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done ifconfig: SIOCGIFFLAGS: No such device be ready to create the interface:[gpon0][gpon0.ani][0]. be ready to get the interface:[gpon0.ani],wanNum:[0]'s macAddr. [MAC_ASSIGN]get_assigned_mac name: gpon0.ani is not wan conn [MAC_ASSIGN]new if, will assign mac by vlanctl. [MAC_ASSIGN]save_assigned_mac name: gpon0.ani is not wan conn [MAC_ASSIGN]save fail. method = HW_NAT_TAB_CLEAN done be ready to create the interface:[gpon0.ani][veip0][0]. be ready to get the interface:[veip0],wanNum:[0]'s macAddr. [MAC_ASSIGN]get_assigned_mac name: veip0 is not wan conn [MAC_ASSIGN]new if, will assign mac by vlanctl. [MAC_ASSIGN]save_assigned_mac name: veip0 is not wan conn [MAC_ASSIGN]save fail. method = HW_NAT_TAB_CLEAN done be ready to create the interface:[gpon0.ani][voip0][0]. be ready to get the interface:[voip0],wanNum:[0]'s macAddr. [MAC_ASSIGN]get_assigned_mac name: voip0 is not wan conn [MAC_ASSIGN]new if, will assign mac by vlanctl. [MAC_ASSIGN]save_assigned_mac name: voip0 is not wan conn [MAC_ASSIGN]save fail. method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done method = HW_NAT_TAB_CLEAN done [01-01 00:00:42][OMCI]saveMsgQueueInfo qid=327690,key=0x30030351 [01-01 00:00:42][OMCI]save new key=0x30030351, qid=327690 to /tmp/omci.q.log rut_initHguAddLan2Bridge........... [01-01 00:00:42][OMCI]thread_id=1961657584 [01-01 00:00:42][OMCI]pid=1698 [01-01 00:00:42][OMCI]saveMsgQueueInfo qid=360459,key=0x1030351 [01-01 00:00:42][OMCI]save new key=0x1030351, qid=360459 to /tmp/omci.q.log libQos_GetOmciQosInfo() get omci qos config is 0 enter hal_lpd_init [01-01 00:00:42][OMCI]evtNotifyHandleFunInit ... [01-01 00:00:42][OMCI]CfgmgrevtNotifyHandleFunInit ... libigmp_GetIGMPMaxGroups() get igmp max group is 256 [01-01 00:00:42][OMCI]configMcastFlow ... lib_get_voipType voiceType 1 lib_get_WifiAsDot11_Status() get PreferWifiAsdot11 is 0 [01-01 00:00:42][OMCI]ConvLayer: enter omci_cvp_proxy_init. [01-01 00:00:42][OMCI]ConvLayer: ONU works with OMCI mode. [01-01 00:00:42][OMCI]saveMsgQueueInfo qid=98307,key=0x61110111 [01-01 00:00:42][OMCI]save new key=0x61110111, qid=98307 to /tmp/omci.q.log omci_cvp_proxy_init: g_vppQ message queue [458766] has been created omci_cvp_proxy_init: register GMI: CVP[01-01 00:00:42][OMCI]saveMsgQueueInfo qid=458766,key=0x61110108 [01-01 00:00:42][OMCI]save new key=0x61110108, qid=458766 to /tmp/omci.q.log ********event message queue has been created[01-01 00:00:42][OMCI]saveMsgQueueInfo qid=491535,key=0x61110109 [01-01 00:00:42][OMCI]save new key=0x61110109, qid=491535 to /tmp/omci.q.log omci_cvp_proxy_init: g_eventQ message queue [491535] has been created omci_cvp_proxy_init: register GMI: CVP for alarm[01-01 00:00:42][OMCI]start cvp_event_proc thread [01-01 00:00:42][OMCI]>>>>getSwVerInfo(),imageBank:0,version:3FE46606BGCA40 [01-01 00:00:42][OMCI]special_process_depended_board: call swdl_commit. [01-01 00:00:42][OMCI]OMCI_LIB: OmciMain:: got 'ONU_SWIMAGE_INFO' with value 0x3 [01-01 00:00:42][OMCI]>>>>getSwVerInfo(),imageBank:1,version:3FE46606BGCA40 [01-01 00:00:42][OMCI]start download_ftpprof_proc thread [01-01 00:00:42][OMCI]start cached_message_proc thread [01-01 00:00:42][OMCI]start dhcp_result_notify_omcilib_proc thread [01-01 00:00:42][OMCI]initialized success [01-01 00:00:42][OMCI]zeroman xml not exist [01-01 00:00:42][OMCI] [01-01 00:00:42][OMCI]start [01-01 00:00:42][OMCI]start [01-01 00:00:42][OMCI]vendorProfile=/configs/alcatel/config/ftpprofile.xml [01-01 00:00:42][OMCI]msg truncated,msgrcv size=33,expected size=112 [01-01 00:00:42][OMCI]response error,expect txn_id=1,resp txn_id=2 [01-01 00:00:42][OMCI]ERROR Send MSG_CVP_FILEDOWNLOADED_NOTIFY_REQ error [01-01 00:00:42][OMCI]profilePath=/configs/alcatel/config/ftpprofile.xml [01-01 00:00:42][OMCI]msg_id=853969 not supported rut_initHguAddLan2Bridge........... [01-01 00:00:42][OMCI]receive MSG_DHCP_RESULT_NOTIFY_TO_OMCILIB,IpHostDataConfigured=0,DisableIpHostDate=0 [01-01 00:00:42][OMCI]valid_fields=0 [01-01 00:00:42][OMCI]defaultNextHop=0 [01-01 00:00:42][OMCI]voipClientIpAddr=1000000 [01-01 00:00:42][OMCI]subnetmask=0 [01-01 00:00:42][OMCI]ftpServerIpAddr=0 [01-01 00:00:42][OMCI]primaryDnsServerIpAddr=0 [01-01 00:00:42][OMCI]secondaryDnsServerIpAddr=0 [01-01 00:00:43][OMCI]OMCI_LIB: Success to create OMCI mib upload share memory, pointer 0x716b6000 nr_commands=17,max_links=200 [01-01 00:00:43][OMCI]checkPonLEDStatus:Fiber disconnected #########################G240WF/G240GE:LED:onustate:1################################ ds_sec=-1 Error: either "to" is duplicate, or "v99" is a garbage. Inside GatewayUniSupp_1Itf::GatewayUniSupp_1Itf constructor iptables: No chain/target/match by that name. getVppEventQid: VPP EVENT message queue [491535] has been createdip6tables: No chain/target/match by that name. PWRSHED_ATTR_SET message received! PwrShed Timers are eth<0> pots<0> ces<0> video<0> xdsl<0> restore<0>, and batteryStatus is <0> [01-01 00:00:43][OMCI]getLoidAuthInfo() exit @ 0m:43s:423ms, : nr_commands=[01-01 00:00:43][OMCI] - create_instance_auto() act_plugInUnitType = 47 18,max_links=200 create auto instanmce gateway uni ME succesful create auto instanmce gateway uni ME succesful create auto instanmce gateway uni ME succesful Error: either "to" is duplicate, or "v99" is a garbage. create auto instanmce gateway uni ME succesful [01-01 00:00:43][OMCI] - create_instance_auto() act_plugInUnitType = 32 OMCI_LIB: VOIP: indexID: 1 OMCI_LIB: No of voip ports after assignment is :2 Error: either "to" is duplicate, or "v99" is a garbage. total no of ports in pots sub card 6 POTS_PORT found with instance ID=513--port no=4 UNI-G auto created for POTS UNI with port num=:4 POTS_PORT found with instance ID=514--port no=5 UNI-G auto created for POTS UNI with port num=:5 [01-01 00:00:43][OMCI]getLoidAuthInfo() exit @ 0m:43s:580ms, : AnigSupp_1 creat [01-01 00:00:43][OMCI]>>>>configLoopDetect(mgmt=1,close_mode=1,detect_interval=2000,rcv_interval=300) enter hal_lpd_set_trans_interval enter hal_lpd_set_restore_interval enter hal_lpd_set_port_info enter hal_lpd_set_port_info enter hal_lpd_set_port_info enter hal_lpd_set_port_info Mib Upload for GatewayUniSupp_1Itf ME Error: either "to" is duplicate, or "v99" is a garbage. rut_initHguAddLan2Bridge........... [01-01 00:00:43][OMCI]special_process_depended_board: call swdl_commit. [01-01 00:00:43][OMCI]OMCI_LIB: Got swImageInfo = 3, standby = 1 [01-01 00:00:43][OMCI]OMCI_LIB: Got swImageInfo = 0, standby = 3 [01-01 00:00:43][OMCI]OMCI_LIB: Got swImageInfo = 0, standby = 5 get slid pwd: 44454641554c54000000 setOmciIK pwd: len=36 44 45 46 41 55 4c 54 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 setOmciIK sn: len=8 41 4c 43 4c fc 3c db 86 hal_mtk_activate_gponlink:31 ret=0 rut_initHguAddLan2Bridge........... iptables: Resource temporarily unavailable. iptables: Bad rule (does a matching rule exist in that chain?). ip6tables: Bad rule (does a matching rule exist in that chain?). enable_t38_same_with_voice 0 [01-01 00:00:44][OMCI]msg truncated,msgrcv size=112,expected size=116 Chain INPUT_FW_VOIP (0 references) Chain INPUT_FW_VOIP (0 references) iptables: Bad rule (does a matching rule exist in that chain?). ip6tables: Bad rule (does a matching rule exist in that chain?). iptables: No chain/target/match by that name. ip6tables: No chain/target/match by that name. iptables v1.4.16.3: unknown option "mangle" Try `iptables -h' or 'iptables --help' for more information. ip6tables v1.4.16.3: unknown option "mangle" Try `ip6tables -h' or 'ip6tables --help' for more information. sed: /etc/dhcpsnoop.conf: No such file or directory sed: /etc/dhcpsnoop.conf: No such file or directory [ndbus][dbus][1291: 0x77eb9320][44.896331][fa][rgwd][ndbusTransmit:104]an error occurred on (0x772b80) when nokia.ndk.dnsproxy.itf.api:LoadHostsCache, ms=5000 : The name nokia.ndk.dnsproxy was not provided by any .service files 1970-01-01 00:00:44[in]cfgmgr Create LANIP: flag=(0);Enable=1;IPInterfaceIPAddress=192.168.1.254;IPInterfaceSubnetMask=255.255.255.0; [startup] cfgmgr rut_setupFireWallChain iptables: Chain already exists. [startup] iptables-restore: [SETUP_CHAIN] xtables-multi iptables-restore -n /tmp/iptablesV4_1386_1; rm /tmp/iptablesV4_1386_1 [iptables-restore] restore /tmp/iptablesV4_1386_1(63 entries) took 0.54s, totalCmd took 1.191. [startup] cfgmgr rut_setupIpv4DosProtection [startup] iptables-restore: [DOS_PROT_TCP] xtables-multi iptables-restore -n /tmp/iptablesV4_1386_2; rm /tmp/iptablesV4_1386_2 iptables: No chain/target/match by that name. ip6tables: No chain/target/match by that name. iptables: No chain/target/match by that name. getVppEventQid: VPP EVENT message queue [491535] has been creatediptables v1.4.16.3: DSCP: bad value for option "--set-dscp", or out of range (0-63). Try `iptables -h' or 'iptables --help' for more information. ip6tables v1.4.16.3: DSCP: bad value for option "--set-dscp", or out of range (0-63). Try `ip6tables -h' or 'ip6tables --help' for more information. enable_t38_same_with_voice 0 [iptables-restore] restore /tmp/iptablesV4_1386_2(6 entries) took 1.132s, totalCmd took 2.323. [startup] iptables-restore: [SUB_DOS_PROT] xtables-multi iptables-restore -n /tmp/iptablesV4_1386_3; rm /tmp/iptablesV4_1386_3 [iptables-restore] restore /tmp/iptablesV4_1386_3(15 entries) took 0.51s, totalCmd took 2.374. [startup] iptables-restore: [SUB_DOS_PROT] xtables-multi iptables-restore -n /tmp/iptablesV4_1386_4; rm /tmp/iptablesV4_1386_4 getVppEventQid: VPP EVENT message queue [491535] has been createdenable_t38_same_with_voice 0 [iptables-restore] restore /tmp/iptablesV4_1386_4(7 entries) took 0.43s, totalCmd took 2.417. [01-01 00:00:46][OMCI]imgVersionStrsion=3FE46606BGCA40 [01-01 00:00:46][OMCI]pImgVersionNum=6.2.0.140 iptables v1.4.16.3: Couldn't find match `unclean' Try `iptables -h' or 'iptables --help' for more information. [startup] cfgmgr rut_setupIpv4DosProtection done ip6tables-restore: line 41 failed [iptables-restore-v6] restore /tmp/iptablesV6_1386_1(77 entries) took 0.33s, totalCmd took 3.33. ip6tables v1.4.16.3: Couldn't find target `DOS_LOG_AND_DROP' Try `ip6tables -h' or 'ip6tables --help' for more information. ip6tables v1.4.16.3: Couldn't find target `DOS_LOG_AND_DROP' Try `ip6tables -h' or 'ip6tables --help' for more information. ip6tables v1.4.16.3: Couldn't find target `DOS_PROT_TCP' Try `ip6tables -h' or 'ip6tables --help' for more information. ip6tables: No chain/target/match by that name. ip6tables v1.4.16.3: Couldn't find target `DOS_LOG_AND_DROP' Try `ip6tables -h' or 'ip6tables --help' for more information. ip6tables v1.4.16.3: Couldn't find target `DOS_PROT_UDP' Try `ip6tables -h' or 'ip6tables --help' for more information. ip6tables v1.4.16.3: Couldn't find target `DOS_LOG_AND_DROP' Try `ip6tables -h' or 'ip6tables --help' for more information. ip6tables: No chain/target/match by that name. ip6tables v1.4.16.3: Couldn't find target `DOS_LOG_AND_DROP' Try `ip6tables -h' or 'ip6tables --help' for more information. ip6tables v1.4.16.3: Couldn't find target `DOS_PROT_ICMP' Try `ip6tables -h' or 'ip6tables --help' for more information. [startup] cfgmgr rut_setupFireWallChain done iptables: No chain/target/match by that name. [startup] iptables-restore: [NAT] xtables-multi iptables-restore -n /tmp/iptablesV4_1386_5; rm /tmp/iptablesV4_1386_5 [iptables-restore] restore /tmp/iptablesV4_1386_5(28 entries) took 0.33s, totalCmd took 3.324. [startup] cfgmgr rut_InitIptablesNat done [startup] cfgmgr insertModuleInfo [startup] cfgmgr insertModuleInfo done 1970-01-01 00:00:47[in]DosProtection enable [startup] cfgmgr rut_setupDropAckRule [startup] iptables-restore: [DROP_ACK] xtables-multi iptables-restore -n /tmp/iptablesV4_1386_6; rm /tmp/iptablesV4_1386_6 set obc limitation successful[iptables-restore] restore /tmp/iptablesV4_1386_6(20 entries) took 0.57s, totalCmd took 3.427. [startup] cfgmgr rut_setupDropAckRule done [startup] cfgmgr rut_setupFixedHostServiceRulesForFilter UserAgentPort=5060 liuchi localPortMin=22456 localPortMax=22584 liuchi [startup] iptables-restore: [FWLEVEL] xtables-multi iptables-restore -n /tmp/iptablesV4_1386_7; rm /tmp/iptablesV4_1386_7 [iptables-restore] restore /tmp/iptablesV4_1386_7(44 entries) took 0.82s, totalCmd took 3.700. ip6tables-restore: line 3 failed [iptables-restore-v6] restore /tmp/iptablesV6_1386_2(50 entries) took 0.112s, totalCmd took 3.812. [startup] cfgmgr rut_setupFixedHostServiceRulesForFilter done (non VFSP) [startup] cfgmgr rutIpt_initIpFilterOutChain [startup] iptables-restore: [IP_FILTER] xtables-multi iptables-restore -n /tmp/iptablesV4_1386_8; rm /tmp/iptablesV4_1386_8 [iptables-restore] restore /tmp/iptablesV4_1386_8(25 entries) took 0.37s, totalCmd took 3.849. [startup] cfgmgr rutIpt_initIpFilterOutChain done conntrack v1.0.0 (conntrack-tools): Invalid IP address `--dport' Try `conntrack -h' or 'conntrack --help' for more information. [startup] iptables-restore: [LAN_ACCESS] xtables-multi iptables-restore -n /tmp/iptablesV4_1386_9; rm /tmp/iptablesV4_1386_9 [iptables-restore] restore /tmp/iptablesV4_1386_9(7 entries) took 0.56s, totalCmd took 3.925. ip6tables-restore: line 2 failed [iptables-restore-v6] restore /tmp/iptablesV6_1386_3(6 entries) took 0.86s, totalCmd took 4.11. killall: dropbear: no process killed enter hal_lpd_init enter hal_lpd_set_port_info enter hal_lpd_set_port_info enter hal_lpd_set_port_info enter hal_lpd_set_port_info Function rutIpt_portalLoidWeb() is called Starting Dropbear SSH server: [startup stage1_boot 17/71] <- cfgmgr cfg_bootSfuLan [7563ms] [startup on_idle 20/71] -> cfgmgr cfg_bootWlan [startup on_idle 20/71] <- cfgmgr cfg_bootWlan [0ms] UplinkMgrCfg: WorkMode: 0 DetectMethod: 0 VFSPUplinkMgrTrack: Interval: 5 DataBackupMode: 0 SwitchToMobileFlag: 0 MobileDisconnectIdleTime: 600 IsActiveLanHostAvailable_m: 0 ICMPQueryInterval: 4 Gateway: DNSQueryInterval: 4 DNSQueryUrl: DataWanToMobileDelayTime: 0 DataMobileToWanDelayTime: 0 dropbear. [ndbus][dbus][1500: 0x7729a320][48.565715][wa][uplinkmgr][ndbusMainLoop:555]Main thread errno address:0x7729a798 [ndbus][dbus][1500: 0x7561d4f0][48.568044][wa][uplinkmgr][thread_entry:463]Child thread errno address:0x7561d968 [startup on_idle 26/71] -> cfgmgr cfg_bootLog [startup on_idle 26/71] <- cfgmgr cfg_bootLog [25ms] [startup on_idle 28/71] -> cfgmgr cfg_bootpppoeemulation sh: /sbin/pppoeemulation: not found [startup on_idle 28/71] <- cfgmgr cfg_bootpppoeemulation [13ms] [startup on_idle 30/71] -> cfgmgr cfg_bootArpWan wanlived starting with pid 2202 wand starting ... interval = 60 net.ipv4.ping_group_range = 0 0 [startup on_idle 30/71] <- cfgmgr cfg_bootArpWan [167ms] led_mode=0 is_intercept_enabled=0 [ndbus][dbus][2205: 0x77185000][50.102383][wa][wanlived][ndbusMainLoop:555]Main thread errno address:0x77185468 [ndbus][dbus][2205: 0x76b084f0][50.105303][wa][wanlived][thread_entry:463]Child thread errno address:0x76b08958 [startup on_idle 38/71] -> cfgmgr cfg_bootUser ONTUSER adminadmin [startup on_idle 38/71] <- cfgmgr cfg_bootUser [828ms] [startup on_idle 39/71] -> cfgmgr cfg_bootFtp killall: utelnetd: no process killed telnetd: starting max_connection=8 port: 23; interface: any; login program: /bin/login killall: proftpd: no process killed [startup on_idle 39/71] <- cfgmgr cfg_bootFtp [386ms] [startup on_idle 48/71] -> cfgmgr cfg_bootAlg [startup on_idle 48/71] <- cfgmgr cfg_bootAlg [664ms] [startup on_idle 54/71] -> cfgmgr cfg_bootSecurity killall: detect: no process killed [startup on_idle 54/71] <- cfgmgr cfg_bootSecurity [160ms] [startup on_idle 57/71] -> cfgmgr cfg_bootP2P [startup on_idle 57/71] <- cfgmgr cfg_bootP2P [1ms] [startup on_idle 70/71] -> cfgmgr cfg_bootBufferBloatEffectFlag [startup on_idle 70/71] <- cfgmgr cfg_bootBufferBloatEffectFlag [3ms] prepare to reset boot_fail_num reset boot_fail_num = 0 done current image is :image0 image0_version=3FE46606BGCA40 image1_version=3FE46606BGCA40 commit =[0] next_active =[0] image0_is_valid =[1] image1_is_valid =[0] boot_fail_num =[0]


COPY HERE THE BOOTLOG ONCE OPENWRT IS INSTALLED AND RUNNING


This website uses cookies. By using the website, you agree with storing cookies on your computer. Also you acknowledge that you have read and understand our Privacy Policy. If you do not agree leave the website.More information about cookies
  • Last modified: 2024/03/05 08:39
  • by alexceltare2